PROJECT NAME:

P.T.S.C MODULAR BUILDING

DONE BY A.D CHECKED BY A.D DATE 4/17/2019
Z-PURLINS ATTACHED TO THROUGH- REVISION:
TITLE:
FASTENED ROOF 1.0
REFERENCE Output
AISI Cold

Neutral axis
Formed (
Steel Spec. 0.8"
2012

4.5"
0.07"

Neutral axis

4.5"

2.5"

The geometric properties are as follows:

Z-SECTION- 9CS2.5x070

 
  0.07 in.
  9.00 in.
  2.5 in.
'  0.188 in
  0.8 in.
  1.05 in.2

 12.2 in.4
  0.828 in.4

 2.71 in.3
&  2.470 in.3
  0.447 in.3
  0.89 in.
)  3.9 in.
*  0.0017 in.4
(  14.2 in.6
%  29500 ksi
The material properties are as follows:

ASTM A653SQ Gr 33
Fy= 55 ksi.
Fu= 45 ksi.

!  #
ℎ ,   14 ft.

 
ℎ  14 °
! 

 " 
ℎ  3 ft.
   20 psf
   2.5 psf
     ⊥ 22 psf

  7.277 lb./ft.  0.007 kip/ft.

  58.22 lb./ft.  0.058 kip/ft.
  66 lb./ft.  0.066 kip/ft.
 PROJECT NAME:
P.T.S.C MODULAR BUILDING
DONE BY A.D CHECKED BY A.D DATE 4/17/2019
Z-PURLINS ATTACHED TO THROUGH- REVISION:
TITLE:
FASTENED ROOF 1.0
REFERENCE Output

From Chapter 2 of ASCE/SEI 7, the required flexural strength is:

+,  1.20 1 1.634  0.10 kip/ft.

+ 2
5,   2.496 kip-ft.
8
+
GH
  0.713 kips
2

At location of maximum positive moment

The section is assumend to be fully braced against lateral torsional buckling, but sitorsional buckling and
yielding strengths must be calculated

Calculating the allowable distorsional buckling strengths per section C3.1.4.

The elastic distortional buckling stress , Fd

The cross section has a single web and single edge -stiffened flange as required by Section C3.1.4(a)
considering the contribution of the attached roof panel , which ahas a rotational stiffness

78  0.300 kip-in./rad./in

From Table II-7/II/9

78&  0.378 kip
78  0.0118 in2
78&  0.354 kip
78  0.0025 in2

There is no significant moment gradient in the vicinity of the maximum positive moment β=1.0

The elastic distortional buckling stress, Fd

7;& 7;& 7;
C3.1.4-6 90  :  72.42 ksi.
7; 1 7;

C3.1.4-4 5  < 9  149.1 kip-in.

C3.1.4-5 5=40  < 90  196.3 kip-in.

C3.1.4-3 >0  5 /5=40  0.871 > 0.674

C.D C.D
5=40 5=40
C3.1.4-2 5@  1 A 0.22 5  127.9 kip-in.
5 5
EF 5@  9.589 kip-ft. > 2.50 kip-ft O.k

The design strength based on initiation of yielding per section C3.1.1(a)

C3.1.1.1-1 5  <& 9  135.9 kip-in.

A5.1.1-1 EF 5@  10.19 kip-ft. > 2.50 kip-ft O.k
 PROJECT NAME:
P.T.S.C MODULAR BUILDING
DONE BY A.D CHECKED BY A.D DATE 4/17/2019
Z-PURLINS ATTACHED TO THROUGH- REVISION:
TITLE:
FASTENED ROOF 1.0
REFERENCE Output

The allowable lateral-torsional buckling strength per Section C3.1.2.1(b)

  47.3 in.
S  1
(F  1.67

V M%
C3.1.2.18 T&  M  103.1 ksi.
S 

1 V M %(
C3.1.2.1-9 T&U  W* 1  116.9 ksi.
 ) M SU U M
(F ) 
C3.1.2.1-4 9&  T& TU  277.1 ksi.
<

C3.1.2.1-1 9=  55 ksi.

EF 5@  10.19 kip-ft. > 2.50 kip-ft O.k

Strength for shear only (section C3.2 )

GH  0.71 kips

ℎ   A 2
A 2'  8.485 in.

Since the web is unreinforced

7I  5.34
K  0.3
ℎ
%7I /9  54 <  121.2 > 80.81  1.51 %7I /9

Using Eq.C3.2.1-4 9I  9.693 ksi.

C3.2.1-1 EG@  E 9I  5.469 kips > 0.71 kip-ft O.k

Strength for combined bending and shear (Section C3.3.3)

M M
L
5 GN
1  0.278 < 1.0 O.k
EF 5@
) EF G@
Web crippling strength (Section C3.4)

Where
O  90 °
'  0.188 in.
P  5 in.

From Table C3.4.1-2 ( 4

(4  0.14
(Q  0.35
(R  0.02
E  0.85
 PROJECT NAME:
P.T.S.C MODULAR BUILDING
DONE BY A.D CHECKED BY A.D DATE 4/17/2019
Z-PURLINS ATTACHED TO THROUGH- REVISION:
TITLE:
FASTENED ROOF 1.0
REFERENCE Output

' P ℎ
Eq C3.4.1-1 E!@  E(U M 9 sin O 1 A (4 1 1 (Q 1 A (R  2.18 kips > 0.71 kips O.k

Check Uplift Loads

Strength for bending only (section D6.1.1) Required strength

By inspection ,load combination 0.9D + 1.0W controls

5H  0.95\ 1 1.05  1.777 kips

Design Strength
' 0.6 assuming all 15 conditions of section D6.1.1 are satisfied

Eq D6.1.1-1 EF 5@  '<& 9  6.113 kip-ft > 1.78 kip-ft O.k