Scribd
Upload
247 views6 pages

اختبار الشد

This document discusses tensile testing of materials and defines key terms related to stress-strain behavior. It provides data from a tensile test on a 14mm mild steel rod, including load, elongation, and fracture point. The task is to plot the stress-strain diagram and determine mechanical properties including proportional limit, modulus of elasticity, yield point, ultimate strength, and rupture strength.

Uploaded by

Ihab El-Sayed
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
247 views6 pages

اختبار الشد

This document discusses tensile testing of materials and defines key terms related to stress-strain behavior. It provides data from a tensile test on a 14mm mild steel rod, including load, elongation, and fracture point. The task is to plot the stress-strain diagram and determine mechanical properties including proportional limit, modulus of elasticity, yield point, ultimate strength, and rupture strength.

Uploaded by

Ihab El-Sayed
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

– Linear elastic: elongation in the specimen that is proportional to the applied

load.
– Stress-strain curves

– Engineering stress: the ratio of the applied load P, to the original cross-sectional
area, Ao, of the specimen.

• Engineering stress equation: σ = P/Ao

• Engineering strain equation: e = (l-lo)/lo

• Yield Stress: the stress at which permanent (plastic) deformation occurs.

• Permanent (plastic) deformation: stress and strain are no longer proportional.

• Ultimate tensile strength (UTS): the maximum engineering stress.

• If the specimen is loaded beyond its UTS it begins to “neck.”

• Fracture stress: the engineering stress at fracture.

• Modulus of elasticity: ratio of stress to strain in the elastic region.

• Modulus of elasticity equation: E = σ/e

• This linear relationship is known as Hooke’s Law.


• Poisons Ratio: the ratio of the lateral strain to the longitudinal strain.

• Ductility: extent of plastic deformation that the material undergoes before fracture.

• Two measures of ductility:

– Total elongation: (lf-lo)/lo x 100%

– Reduction of Area: (Ao-Af)/Ao x 100%

• True-stress: ratio of the load, P, to the instantaneous cross-sectional area, A, of the


specimen.

• True-strain: the sum of all the instantaneous engineering strains.

– True-stress equation: σ = P/A

– True-strain equation: e = ln(l/lo)

The following data were recorded during the tensile test of a 14-mm-diameter
mild steel rod. The gage length was 50 mm.

Load (N) Elongation (mm) Load (N) Elongation (mm)


0 0 46 200 1.25
6 310 0.010 52 400 2.50
12 600 0.020 58 500 4.50
18 800 0.030 68 000 7.50
25 100 0.040 59 000 12.5
31 300 0.050 67 800 15.5
37 900 0.060 65 000 20.0
40 100 0.163 65 500 Fracture
41 600 0.433

Plot the stress-strain diagram and determine the following mechanical


properties: (a) proportional limits; (b) modulus of elasticity; (c) yield point; (d)
ultimate strength; and (e) rupture strength.

Problem 203
The following data were recorded during the tensile test of a 14-mm-diameter
mild steel rod. The gage length was 50 mm.

Load (N) Elongation (mm) Load (N) Elongation (mm)


0 0 46 200 1.25
6 310 0.010 52 400 2.50
12 600 0.020 58 500 4.50
18 800 0.030 68 000 7.50
25 100 0.040 59 000 12.5
31 300 0.050 67 800 15.5
37 900 0.060 65 000 20.0
40 100 0.163 65 500 Fracture
41 600 0.433

Plot the stress-strain diagram and determine the following mechanical


properties: (a) proportional limits; (b) modulus of elasticity; (c) yield point; (d)
ultimate strength; and (e) rupture strength.

Area, A = 0.25π(142) = 49π mm2


Length, L = 50 mm
Strain = Elongation/Length
Stress = Load/Area

Load (N) Elongation (mm) Strain (mm/mm) Stress (MPa)

Elongation Strain Stress


Load (N)
(mm) (mm/mm) (MPa)
0 0 0 0
6 310 0.010 0.0002 40.99
12 600 0.020 0.0004 81.85
18 800 0.030 0.0006 122.13
25 100 0.040 0.0008 163.05
31 300 0.050 0.001 203.33
37 900 0.060 0.0012 246.20
40 100 0.163 0.0033 260.49
41 600 0.433 0.0087 270.24
46 200 1.250 0.025 300.12
52 400 2.500 0.05 340.40
58 500 4.500 0.09 380.02
68 000 7.500 0.15 441.74
59 000 12.500 0.25 383.27
67 800 15.500 0.31 440.44
65 000 20.000 0.4 422.25
61 500 Failure 399.51

399.51

The area of the circle of given diameter d is: A=14πd2A=14πd2


Note that 1/4 = 0.25 in decimal form.

You might also like