Field Charger/Power Supply

FCPS-24FS6 & FCPS-24FS8

FCPS-24FS6E & FCPS-24FS8E
FCPS-24FS6C & FCPS-24FS8C
Installation Manual

H1
Document 51883
4/14/2011 Rev:
P/N 51883:H1 ECN 11-237
 Fire Alarm System Limitations
While a fire alarm system may lower insurance rates, it is not a substitute for fire insurance!
An automatic fire alarm system—typically made up of Heat detectors do not sense particles of combustion and
smoke detectors, heat detectors, manual pull stations, audible alarm only when heat on their sensors increases at a predeter-
warning devices, and a fire alarm control panel with remote mined rate or reaches a predetermined level. Rate-of-rise
notification capability—can provide early warning of a develop- heat detectors may be subject to reduced sensitivity over time.
ing fire. Such a system, however, does not assure protection For this reason, the rate-of-rise feature of each detector
against property damage or loss of life resulting from a fire. should be tested at least once per year by a qualified fire pro-
The Manufacturer recommends that smoke and/or heat detec- tection specialist. Heat detectors are designed to protect
tors be located throughout a protected premise following the property, not life.
recommendations of the National Fire Protection Association IMPORTANT! Smoke detectors must be installed in the
Standard 72 (NFPA 72), manufacturer's recommendations, same room as the control panel and in rooms used by the sys-
State and local codes, and the recommendations contained in tem for the connection of alarm transmission wiring, communi-
the Guides for Proper Use of System Smoke Detectors, which cations, signaling, and/or power. If detectors are not so
are made available at no charge to all installing dealers. located, a developing fire may damage the alarm system, crip-
These documents can be found at http://www.systemsen- pling its ability to report a fire.
sor.com/html/applicat.html. A study by the Federal Emer- Audible warning devices such as bells may not alert people
gency Management Agency (an agency of the United States if these devices are located on the other side of closed or
government) indicated that smoke detectors may not go off in partly open doors or are located on another floor of a building.
as many as 35% of all fires. While fire alarm systems are Any warning device may fail to alert people with a disability or
designed to provide early warning against fire, they do not those who have recently consumed drugs, alcohol or medica-
guarantee warning or protection against fire. A fire alarm sys- tion. Please note that:
tem may not provide timely or adequate warning, or simply
may not function, for a variety of reasons: • Strobes can, under certain circumstances, cause seizures
in people with conditions such as epilepsy.
Smoke detectors may not sense fire where smoke cannot
reach the detectors such as in chimneys, in or behind walls, on • Studies have shown that certain people, even when they
roofs, or on the other side of closed doors. Smoke detectors hear a fire alarm signal, do not respond or comprehend the
also may not sense a fire on another level or floor of a building. meaning of the signal. It is the property owner's responsi-
A second-floor detector, for example, may not sense a first- bility to conduct fire drills and other training exercise to
floor or basement fire. make people aware of fire alarm signals and instruct them
on the proper reaction to alarm signals.
Particles of combustion or “smoke” from a developing fire
may not reach the sensing chambers of smoke detectors • In rare instances, the sounding of a warning device can
because: cause temporary or permanent hearing loss.

• Barriers such as closed or partially closed doors, walls, or A fire alarm system will not operate without any electrical
chimneys may inhibit particle or smoke flow. power. If AC power fails, the system will operate from standby
batteries only for a specified time and only if the batteries have
• Smoke particles may become “cold,” stratify, and not reach been properly maintained and replaced regularly.
the ceiling or upper walls where detectors are located.
Equipment used in the system may not be technically com-
• Smoke particles may be blown away from detectors by air patible with the control panel. It is essential to use only equip-
outlets. ment listed for service with your control panel.
• Smoke particles may be drawn into air returns before Telephone lines needed to transmit alarm signals from a
reaching the detector. premise to a central monitoring station may be out of service
The amount of “smoke” present may be insufficient to alarm or temporarily disabled. For added protection against tele-
smoke detectors. Smoke detectors are designed to alarm at phone line failure, backup radio transmission systems are rec-
various levels of smoke density. If such density levels are not ommended.
created by a developing fire at the location of detectors, the The most common cause of fire alarm malfunction is inade-
detectors will not go into alarm. quate maintenance. To keep the entire fire alarm system in
Smoke detectors, even when working properly, have sensing excellent working order, ongoing maintenance is required per
limitations. Detectors that have photoelectronic sensing the manufacturer's recommendations, and UL and NFPA stan-
chambers tend to detect smoldering fires better than flaming dards. At a minimum, the requirements of NFPA 72 shall be
fires, which have little visible smoke. Detectors that have ion- followed. Environments with large amounts of dust, dirt or
izing-type sensing chambers tend to detect fast-flaming fires high air velocity require more frequent maintenance. A main-
better than smoldering fires. Because fires develop in different tenance agreement should be arranged through the local man-
ways and are often unpredictable in their growth, neither type ufacturer's representative. Maintenance should be scheduled
of detector is necessarily best and a given type of detector monthly or as required by National and/or local fire codes and
may not provide adequate warning of a fire. should be performed by authorized professional fire alarm
Smoke detectors cannot be expected to provide adequate installers only. Adequate written records of all inspections
warning of fires caused by arson, children playing with should be kept.
matches (especially in bedrooms), smoking in bed, and violent
explosions (caused by escaping gas, improper storage of Limit-C1-2-2007

flammable materials, etc.).

2 FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011
 Installation Precautions
Adherence to the following will aid in problem-free installation with long-term reliability:
WARNING - Several different sources of power can be Like all solid state electronic devices, this system may
connected to the fire alarm control panel. Disconnect all operate erratically or can be damaged when subjected to light-
sources of power before servicing. Control unit and associ- ning induced transients. Although no system is completely
ated equipment may be damaged by removing and/or insert- immune from lightning transients and interference, proper
ing cards, modules, or interconnecting cables while the unit is grounding will reduce susceptibility. Overhead or outside aerial
energized. Do not attempt to install, service, or operate this wiring is not recommended, due to an increased susceptibility
unit until manuals are read and understood. to nearby lightning strikes. Consult with the Technical Ser-
CAUTION - System Re-acceptance Test after Software vices Department if any problems are anticipated or encoun-
Changes: To ensure proper system operation, this product tered.
must be tested in accordance with NFPA 72 after any pro- Disconnect AC power and batteries prior to removing or
gramming operation or change in site-specific software. Re- inserting circuit boards. Failure to do so can damage circuits.
acceptance testing is required after any change, addition or Remove all electronic assemblies prior to any drilling, filing,
deletion of system components, or after any modification, reaming, or punching of the enclosure. When possible, make
repair or adjustment to system hardware or wiring. All compo- all cable entries from the sides or rear. Before making modifi-
nents, circuits, system operations, or software functions known cations, verify that they will not interfere with battery, trans-
to be affected by a change must be 100% tested. In addition, former, or printed circuit board location.
to ensure that other operations are not inadvertently affected,
at least 10% of initiating devices that are not directly affected Do not tighten screw terminals more than 9 in-lbs. Over-
by the change, up to a maximum of 50 devices, must also be tightening may damage threads, resulting in reduced terminal
tested and proper system operation verified. contact pressure and difficulty with screw terminal removal.

This system meets NFPA requirements for operation at 0-49º This system contains static-sensitive components.
C/32-120º F and at a relative humidity 93% ± 2% RH (non- Always ground yourself with a proper wrist strap before han-
condensing) at 32°C ± 2°C (90°F ± 3°F). However, the useful dling any circuits so that static charges are removed from the
life of the system's standby batteries and the electronic com- body. Use static suppressive packaging to protect electronic
ponents may be adversely affected by extreme temperature assemblies removed from the unit.
ranges and humidity. Therefore, it is recommended that this Follow the instructions in the installation, operating, and pro-
system and its peripherals be installed in an environment with gramming manuals. These instructions must be followed to
a normal room temperature of 15-27º C/60-80º F. avoid damage to the control panel and associated equipment.
Verify that wire sizes are adequate for all initiating and indi- FACP operation and reliability depend upon proper installation.
cating device loops. Most devices cannot tolerate more than a Precau-D1-9-2005
10% I.R. drop from the specified device voltage.

FCC Warning
WARNING: This equipment generates, uses, and can Canadian Requirements
radiate radio frequency energy and if not installed and This digital apparatus does not exceed the Class A limits
used in accordance with the instruction manual may for radiation noise emissions from digital apparatus set
cause interference to radio communications. It has been out in the Radio Interference Regulations of the Cana-
tested and found to comply with the limits for class A dian Department of Communications.
computing devices pursuant to Subpart B of Part 15 of
FCC Rules, which is designed to provide reasonable Le present appareil numerique n'emet pas de bruits
protection against such interference when devices are radioelectriques depassant les limites applicables aux
operated in a commercial environment. Operation of this appareils numeriques de la classe A prescrites dans le
equipment in a residential area is likely to cause interfer- Reglement sur le brouillage radioelectrique edicte par le
ence, in which case the user will be required to correct ministere des Communications du Canada.
the interference at his or her own expense.

LiteSpeed™ is a trademark; and FireLite® Alarms is a registered trademark of Honeywell International Inc. Microsoft® and Windows® are registered
trademarks of the Microsoft Corporation.
©2011 by Honeywell International Inc. All rights reserved. Unauthorized use of this document is strictly prohibited.

FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011 3

Software Downloads
In order to supply the latest features and functionality in fire alarm and life safety technology to our customers, we make
frequent upgrades to the embedded software in our products. To ensure that you are installing and programming the latest
features, we strongly recommend that you download the most current version of software for each product prior to
commissioning any system. Contact Technical Support with any questions about software and the appropriate version for
a specific application.

Documentation Feedback
Your feedback helps us keep our documentation up-to-date and accurate. If you have any comments or suggestions about
our online Help or printed manuals, you can email us.
Please include the following information:
•Product name and version number (if applicable)
•Printed manual or online Help
•Topic Title (for online Help)
•Page number (for printed manual)
•Brief description of content you think should be improved or corrected
•Your suggestion for how to correct/improve documentation
Send email messages to:
[email protected]
Please note this email address is for documentation feedback only. If you have any technical issues, please contact
Technical Services.

4 FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011

 Table of Contents
Section 1: System Overview .................................................................................................... 8
1.1: General...........................................................................................................................................................8
1.2: Features..........................................................................................................................................................8
1.3: Start-up Procedure .........................................................................................................................................9
1.4: Jumpers ........................................................................................................................................................10
1.4.1: Jumper JP1 - Ground Fault Detection ...............................................................................................10
1.4.2: Jumpers JP2 and JP3: Coded/Noncoded Input Selection ..................................................................10
1.5: LED Indicators.............................................................................................................................................10
1.6: Specifications...............................................................................................................................................10
1.7: General.........................................................................................................................................................13
Section 2: Installation............................................................................................................. 14
2.1: Backbox Mounting ......................................................................................................................................14
2.2: NAC Circuit Wiring.....................................................................................................................................16
2.2.1: Style Y (Class B) ...............................................................................................................................16
2.2.2: ZNAC-4 Class A Option Module......................................................................................................16
2.3: Addressable Module Mounting ...................................................................................................................17
2.4: NEC Power-limited Wiring Requirements ..................................................................................................18
Section 3: Programming Options.......................................................................................... 19
3.1: DIP Switch Settings .....................................................................................................................................20
3.2: Programmable Features Description............................................................................................................21
3.2.1: Synchronization Type Selection........................................................................................................21
Maximum Number of Strobes for Synchronization .............................................................................21
3.2.2: Synchronization Mode - Master/Slave ..............................................................................................21
3.2.3: AC Fail Delay/Aux. Trouble Relay Function....................................................................................22
3.2.4: Input/Output Function .......................................................................................................................22
Auxiliary Power Control ......................................................................................................................23
3.2.5: Charger Enable/Disable.....................................................................................................................23
3.2.6: Door Closers ......................................................................................................................................23
Section 4: Trouble Supervision ............................................................................................. 25
4.1: Supervision via FACP Notification Appliance Circuit................................................................................25
4.1.1: Supervision of FACP to FCPS wiring...............................................................................................25
4.1.2: Supervision of FCPS-24FS Faults.....................................................................................................25
4.1.3: Aux. Trouble Relay/AC Fail Relay ...................................................................................................25
4.2: AC Loss Reporting Delay............................................................................................................................26
Section 5: Applications .......................................................................................................... 27
5.1: Controlling Four NACs With One Input and Selective Silence ..................................................................27
5.2: Controlling Three NACs and One Door Holder With One Input................................................................29
5.3: Split Temporal Mode of Operation..............................................................................................................31
5.4: Remote Supply With Resettable and Nonresettable Power.........................................................................33
5.5: Master FACP with Slave FCPS-24FS Power Supply..................................................................................35
5.6: Master FCPS-24FS Power Supply Connected to FACP..............................................................................36
5.7: Canadian Applications.................................................................................................................................36
Section 6: Power Supply Requirements ............................................................................... 38
6.1: Overview......................................................................................................................................................38
6.2: Calculating the AC Branch Circuit..............................................................................................................38
6.3: Calculating the System Current Draw .........................................................................................................39
6.3.1: Overview ...........................................................................................................................................39
6.3.2: How to Calculate System Current Draw ...........................................................................................39
6.4: Calculating the Battery Size ........................................................................................................................41
6.4.1: NFPA Battery Requirements .............................................................................................................41
6.4.2: Selecting and Locating Batteries .......................................................................................................41

FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011 5

Table of Contents

Appendix A: Wire Requirements........................................................................................... 43

Index ........................................................................................................................................ 44

6 FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011

 It is imperative that the installer understand the requirements of the Authority Having Jurisdiction
(AHJ) and be familiar with the standards set forth by the following regulatory agencies:
• Underwriters Laboratories Standards
• NFPA 72 National Fire Alarm Code

Before proceeding, the installer should be familiar with the following documents.

NFPA Standards
NFPA 72 National Fire Alarm Code
NFPA 70 National Electrical Code

Underwriters Laboratories Documents:

UL 464 Audible Signaling Appliances
UL 864 Standard for Control Units for Fire Protective Signaling Systems
UL 1638 Visual Signaling Appliances
UL 1971 Signaling Devices for Hearing Impaired

CAN/ULC - S524-01 Standard for Installation of Fire Alarm Systems

CAN/ULC-S527-99 Standard for Control Units for Fire Alarm Systems

Other:
NEC Article 250 Grounding
NEC Article 300 Wiring Methods
NEC Article 760 Fire Protective Signaling Systems
Applicable Local and State Building Codes
Requirements of the Local Authority Having Jurisdiction (LAHJ)
Canadian Electrical Code, Part 1

Other Fire•Lite Documents:

Device Compatibility Document Document #15384

This product has been certified to comply with the requirements in the Standard for Control Units
and Accessories for Fire Alarm Systems, UL 864, 9th Edition. Operation of this product with prod-
ucts not tested for UL 864, 9th Edition has not been evaluated. Such operation requires the
approval of the local Authority Having Jurisdiction (AHJ).

FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011 7

 Section 1: System Overview
The FCPS-24FS6 is a 6 amp power supply and the FCPS-24FS8 is an 8 amp power supply. Each
FCPS-24FS power supply is a compact, cost-effective, remote power supply and battery charger
which provides ADA compatible strobe synchronization. Each remote power supply consists of a
filtered 24 VDC output that can be configured to drive four Style Y (Class B) NACs (Notification
Appliance Circuits). The four circuits can be configured for Style Z (Class A) with the optional
ZNAC-4 Class A converter module. Alternatively, the four output circuits may be configured as 24
VDC resettable or nonresettable power outputs. The input circuits, which control the power supply
operation, are triggered by the reverse polarity of an NAC or by a 12 VDC or 24 VDC power
source. The power supplies are compatible with 12 VDC and 24 VDC control panels.
The FCPS-24FS6E and FCPS-24FS8E offer the same features as the FCPS-24FS6 and FCPS-
24FS8 respectively but allow connection to 220/240 VAC. Unless otherwise specified, the infor-
mation in this manual applies to both the 110/120 VAC versions and the 220/240 VAC versions of
the power supplies.
The FCPS-24FS6C and FCPS-24FS8C are the Canadian versions which offer the same features as
the FCPS-24FS6 and FCPS-24FS8 respectively. Unless otherwise specified, the information in this
manual also applies to the Canadian versions of the power supplies.

1.1 General
The FCPS-24FS power supplies can be used as remotely mounted power supplies and battery char-
gers to power four noncoded or coded NACs. The Main FACP (Fire Alarm Control Panel) NAC(s)
is connected to the remote power supply input circuit(s). When the control input circuit activates
due to reverse polarity of the NAC from the FACP, the power supply will activate its Notification
Appliance Circuits.
During the inactive or nonalarm state, the power supply supervises its NAC field wiring for short
and open conditions. AC fail, battery, charger and ground fault troubles will also be monitored by
the power supply. If an NAC or power supply fault is detected, the power supply Normally-Closed
Trouble contact will open.
If an alarm condition occurs and the NAC is activated, the supervision is disabled and the Notifica-
tion Appliance Circuit is no longer supervised (except for shorts). Supervision of other power sup-
ply faults such as low battery, AC loss, ground fault and battery charger trouble will continue and
may be monitored via the Trouble relay contacts.

1.2 Features
• Self-contained in a lockable cabinet
• 24 VDC remote power supply
• Outputs are completely power-limited
• Two optically-isolated input/control circuits, compatible with 12 VDC and 24 VDC control
panel NACs
• Four output circuits:
– Fully filtered power
– Four 24 VDC Style Y (Class B) NACs (special application)
– Optional ZNAC-4 Class A converter module for conversion to Style Z NACs
– Alternatively, all four circuits may be configured as 24 VDC special application power
outputs
– Output circuits may be configured as resettable or nonresettable
• NAC Trouble LED - blinks to indicate the number of the circuit in trouble
• Maximum current available for any one output circuit: 3.0 amps

8 FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011

Start-up Procedure System Overview

• Maximum total continuous current available:

– 4.0 amps for FCPS-24FS6
– 6.0 amps for FCPS-24FS8
• Maximum total short term current (one hour maximum):
– 6.0 amps for FCPS-24FS6
– 8.0 amps for FCPS-24FS8
• Integral supervised battery charger for lead acid batteries only
• Capable of charging 7.0 AH to 18.0 AH (Amp Hour) batteries
• Fully supervised power supply, battery and NACs
• Selectable Strobe Synchronization for NACs (System Sensor, Gentex and Wheelock)
• Coded signal synchronization
• Fixed terminal blocks for field wiring capable of accepting 12 - 22 AWG wire
• Selectable Ground Fault detection by jumper JP1
• Power supply trouble Form-C relay contacts (fail-safe)
• Optional delay of AC loss reporting for 2 hours
• Auxiliary Special Application Power Output for SLC modules (500 mA maximum) with
optional reset for 4-wire smoke detectors
• Mounting location for optional addressable control module

1.3 Start-up Procedure

1. Configure the power supply jumpers as described in “Jumpers” on page 10.
2. Install the power supply as described in“Installation” on page 14.
3. Program the power supply as described in “Programming Options” on page 19.
4. Wire the power supply circuits, referring to the options described in“Trouble Supervision” on
page 25 and the application examples in“Applications” on page 27.
5. Connect primary power source wiring while observing the following:
– Make certain that the AC mains circuit breaker is off before making any wiring connections
between the mains and the power supply.
– Make certain primary power source is 120 VAC, 60 Hz, 3.2 amps.
– Run a pair of wires (with ground conductor) from the protected premises main breaker box
to TB1 of the power supply main circuit board.
– Use 14 AWG (1.6 mm O.D.) or heavier gauge wire with 600V insulation.
6. Apply power to the power supply using the following procedure:
– Apply AC power by turning on the AC mains circuit breaker connected to the power supply.
– Connect a properly charged battery to connector JP4 on the power supply main circuit
board.

FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011 9

System Overview Jumpers

1.4 Jumpers
CAUTION: DISCONNECT POWER
! REMOVE ALL POWER (AC & DC) BEFORE CUTTING OR MOVING ANY JUMPERS.

1.4.1 Jumper JP1 - Ground Fault Detection

The Ground Detection circuit monitors for zero impedance between the power supply and ground.
Jumper JP1 is located in the top right section of the power supply circuit board. Cutting JP1 will
disable ground fault detection by the power supply. This should only be done if ground faults are
being monitored by a panel connected to the FCPS power supply.

1.4.2 Jumpers JP2 and JP3: Coded/Noncoded Input Selection

Jumpers JP2 and JP3 are located in the top right section of the power
supply circuit board. JP2 is used for Control Input Circuit #1 and
JP3 is used for Control Input Circuit #2. The position of these jump- JP3 JP2
ers will depend on the type of signal being fed to the input circuits:

24s8jp3b.wmf
• If the source voltage to the input circuit is a noncoded (steady
voltage) input signal, the jumper for the corresponding input
circuit should be in the default position which jumpers the
jumpers
bottom two pins (as illustrated in drawing at left).
Jumper positions shown
• If the source voltage to the input circuit is coded (variable for noncoded (steady)
voltage), the jumper for the corresponding input circuit should source voltage
be moved to jumper the top two pins.

1.5 LED Indicators

• AC Power on (green) LED - indicates AC power is present
• Ground Fault (yellow) LED - indicates a ground fault condition (zero impedance to ground)
• Battery Trouble (yellow) LED - indicates low or no battery
• NAC Trouble (yellow) LED - indicates a Notification Appliance Circuit trouble (blinks once
for Circuit 1 trouble, twice for Circuit 2 trouble, three times for Circuit 3 trouble and four times
for Circuit 4 trouble. Note that multiple circuits in trouble will cause the LED to blink the
number of the circuit with the highest number)
• ChargerTrouble/AC Loss (yellow) LED - indicates a charger fault or loss of AC power:
– If AC is applied to the power supply without a battery connected, both the Charger
Trouble/AC Loss LED and Battery Trouble LED will turn on simultaneously, indicating that
a battery is not connected.
– When a battery is connected and the power supply is in Normal Mode, if the battery voltage
drops too low or the battery is disconnected, only the Battery Trouble LED will turn on.
– When a battery is connected and the charger develops a problem, only the Charger
Trouble/AC Loss LED will turn on.

1.6 Specifications
Refer to Figure 1.1 on page 12 for terminal locations.
Primary AC Power - TB1
• FCPS-24FS6(C) & FCPS-24FS8(C): 120 VAC, 60 Hz, 3.2 amps maximum
• FCPS-24FS6E & FCPS-24FS8E: 240 VAC, 50 Hz, 1.6 amps maximum
• Wire size: minimum #14 AWG with 600V insulation

10 FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011

Specifications System Overview

Control Input Circuits - TB4, Terminals 3 (+) & 4 (-) and 7 (+) & 8 (-)
• Trigger Input Voltage: 9 to 32 VDC
• Input Current Draw in Alarm Polarity:
– 16 to 32 volts, 2.0 mA maximum per input
– 9 to 16 volts, 1.0 mA maximum per input
NAC/Output Circuits - TB2, Terminals 1 (+) & 2 (-), 3 (+) & 4 (-), 5 (+) & 6 (-) and
7 (+) & 8 (-) alarm polarity
• Supervised, Special Application and power-limited
• Voltage Rating: 24 VDC filtered
• Current:
– Maximum for any one circuit - 3.0 amps
– Maximum total continuous current for all output:
FCPS-24FS6 - 4.0 amps
FCPS-24FS8 - 6.0 amps
– Maximum total short term current (one hour maximum) for all outputs:
FCPS-24FS6 - 6.0 amps
FCPS-24FS8 - 8.0 amps
• Output Circuit Types:
– Four Style Y NACs (require 4.7 KEnd-of-Line Resistors) or
Style Z NACs using the optional ZNAC-4 Class A converter module
OR
– Four resettable or nonresettable 24 VDC power outputs
• Refer to the Fire•Lite Device Compatibility Document #15384 for listed compatible devices.
• For wiring requirements, refer to “Wire Requirements” on page 43.
Trouble Relay Contact Rating - TB5
• Fail-safe Form-C relay (normally energized, transfers with loss of power)
• 5.0 amps @ 24 VDC or 5.0 amps @ 30 VAC
Secondary Power (battery) Charging Circuit - JP4
• Supervised, nonpower-limited
• Supports lead acid type batteries only
• Float Charge Voltage: 27.6 VDC
• Maximum Charge Current: 1.5 A
• Battery fuse (F1) 15A, 32V (Canadian version is nonreplaceable 12A, 32V)
• Maximum Battery Capacity: 18.0 AH
• Minimum Battery Capacity: 7.0 AH
• Power supply draws maximum standby current of 65 mA from batteries
Auxiliary Special Application Power Output - TB4 Terminals 9 (+) & 10 (-)
• Special application power
• Power-limited, nonsupervised
• Voltage Rating: 24 VDC
• Current:
– 170 mA maximum with internal 7.0 Amp Hour batteries

FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011 11

System Overview Specifications

– 500 mA maximum with external 18.0 Amp Hour batteries

Power-limited, Supervised,
Special Application
in NAC Mode
Nonpower-limited
To Transformer #1 NAC/Out 1 +
To Transformer #2 NAC/Out 1 -
Trouble Relay
NAC/Out 2 + Form-C Fail-safe
Supervised, NAC/Out 2 - Nonsupervised
Nonpower-limited NAC/Out 3 + (shown energized)
Earth NAC/Out 3 - Normally Open
AC Neutral NAC/Out 4 + Normally Closed
AC Hot Common
NAC/Out 4 -
OUT4 OUT3 OUT2 OUT1
- NAC4 + - NAC3 + - NAC2 + - NAC1 + TB2
AUX TBL
EARTH NEUT HOT NO NC COM
TB5
8 7 6 5 4 3 2 1
TB1
3 2 1
JP1 Ground Fault
Detection
(cut to disable)
see Note at
bottom of the
J2
JP1
page.
TRANSFORMER 2

J3
J3
JP2
ZNAC-4 Connector
JP2 & JP3
JP3
J1
Coded/Noncoded
Input Selection
TRANSFORMER 1

Auxiliary Output AUX - 10

500 mA Special - Aux. Common
Application Power* AUX + 9
+ Aux. 24 VDC*
IN2- 8
- Control Input 2
IN2+ 7
+ Control Input 2
OUT1- 6
- Out Common
OUT1+ 5
+ Out/Trouble Contact
IN1- 4
F1 - Control Input 1
IN1+ 3
+ Control Input 1
2

24fs8brd.wmf
SYNC IN -
- Sync Input
SYNC IN + 1
- + AC
GND NAC AC/
FLT BATT TRBL CHGR
SW1
ON + Sync Input
JP4 1 2 3 4 5 6 7 8 TB4
BATTERY

JP4 Supervised
+ Battery SW1 *Note: Auxiliary Power
- Battery LEDs Programming Output is power-limited
18 AH, 24 VDC but not supervised
Nonpower-
Charger Trouble/AC Loss (yellow) DIP Switches
F1 (change switch
limited NAC Trouble (yellow)
Battery Fuse settings only
Battery Trouble (yellow) when all power
15A, 32V
(Canadian version Ground Fault (yellow) (AC & DC) is
is nonreplaceable removed)
AC Power (green)
12 A, 32V)
Figure 1.1 FCPS-24FS Board Layout

NOTE: Cutting Ground Fault jumper JP1 voids UL/NFPA Style/Class identifications for circuits
unless Ground Faults are being monitored by an FACP connected to the power supply. Cut
jumper JP1 only if a panel connected to the power supply is monitoring for Ground Faults or with
the approval of AHJ (Authority Having Jurisdiction).

12 FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011

General System Overview

1.7 General
The FCPS may be used in a number of different applications. It may be used as a remotely-
mounted power supply and battery charger where it can provide up to four coded or noncoded, syn-
chronized or nonsynchronized NACs (Notification Appliance Circuits). Alternatively, output #4
can be used as a door holder circuit which will provide a steady 24 VDC output until an alarm con-
dition or AC fail condition causes it to drop to 0 VDC following a 10 second delay. All four out-
puts can also provide power.

Style Y NAC
Note: All NAC or Door
outputs can be Holder Power
converted to Style Z Style Y NAC Style Y NAC Style Y NAC FCPS Trouble
Output #4 Output #3 Output #2 Output #1 Contact Output
with a ZNAC-4
option module

24 VDC Specific
AC Power Application Power

Input/Output Functions are Programmable

by SW1 DIP Switch Settings NAC Control
Input #2
(from FACP)

NAC Control
Input #1
(from FACP)

Sync. Input

24fsblok.wmf

Battery Charger

Figure 1.2 Simplified FCPS Block Diagram

One possible application for the FCPS remote power supply utilizes the NAC repeater feature. In
this application, one or two NACs are connected from the main FACP to the remote power supply
control input circuits. When the control input circuits are activated by the reverse polarity of the
NACs, the power supply will activate its corresponding output circuits as programmed by SW1
DIP switch configuration (refer to Table 3.1 on page 20).
During the inactive state, the remote power supply supervises its NAC field wiring for short and
open conditions. If a fault is detected, the power supply will enter a trouble condition and illumi-
nate the NAC Trouble LED. When the NACs are activated, the supervision is disabled and the cir-
cuits are no longer supervised (except for short circuit conditions). Supervision of other power
supply faults such as low battery, battery charger trouble, ground fault and AC loss will continue
and may be monitored via the power supply trouble relay.
If an application requires that all four outputs activate at the same time, only one NAC is required
from the FACP. For this application, the NAC is connected to control input circuit #1 and SW1
DIP switch is set for this operation.

FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011 13

 Section 2: Installation
Carefully unpack the system and check for shipping damage. Select a location for the cabinet that
is in a clean, dry, vibration-free area where extreme temperatures are not encountered. The area
should be readily accessible with sufficient room to easily install and maintain the power supply.
Locate the top of the cabinet approximately five feet above the floor with the hinge mounting on
the left. Determine the number of conductors required for the devices to be installed and determine
the appropriate knockouts. All wiring must be in accordance with the National and/or Local codes
for fire alarm systems and power supplies.

2.1 Backbox Mounting

CAUTION: STATIC SENSITIVE COMPONENTS
! THE CIRCUIT BOARD CONTAINS STATIC-SENSITIVE COMPONENTS. ALWAYS GROUND
YOURSELF WITH A PROPER WRIST STRAP BEFORE HANDLING ANY BOARDS SO THAT
STATIC CHARGES ARE REMOVED FROM THE BODY. USE STATIC SUPPRESSIVE PACKAGING
TO PROTECT ELECTRONIC ASSEMBLIES.

1. Remove the PC board and transformers from the backbox before installing backbox. Set the
board and transformers aside in a safe, clean place. Avoid static discharge which may damage
static sensitive components on the board.
2. Mark and predrill holes for the top two keyhole mounting bolts.
3. Install two upper fasteners in the wall with the screw heads protruding approximately ¼”.
4. Using the upper keyholes, mount the backbox over the two screws.
5. Mark the lower two holes, remove the backbox from the wall and drill the mounting holes.
6. Mount the backbox, install the remaining fasteners and tighten all screws.
7. When the location is dry and free of construction dust, reinstall the PC board and transformers
and continue with the installation.
8. IMPORTANT! Make certain to connect the supplied grounding strap between the Earth
terminal on TB1 (AC Terminal Block) of the main circuit board and the chassis ground stud as
illustrated in Figure 2.1:

Earth Terminal on TB1 (AC Terminal Block)

Mounting Plate

Grounding Strap

Ground Stud
24fsgrnd.wmf

Backbox

Figure 2.1 Grounding Strap

14 FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011

Backbox Mounting Installation

Top
2.875” (7.3 cm)

Depth = 3.050”
Backbox = 14.5” (7.75 cm)
(36.8 cm)

0.75”
(1.9 cm) 2.7”
9.1” (23.1 cm) (6.86cm)

Ground Stud

10.625”
(26.99 cm)
Height=15.00” Mounting Plate Pem Studs
(38.10 cm)

fcpscabb.wmf
Backbox Mounting Holes

Bottom 1.125” (2.868 cm)

Figure 2.2 Backbox Mounting Dimensions

FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011 15

Installation NAC Circuit Wiring

2.2 NAC Circuit Wiring

2.2.1 Style Y (Class B)
The standard configuration for NACs is Style Y (Class B) as shown in Figure 2.3.

4.7K ELR

Alarm Polarity Shown Horn Strobe

Horn Strobe

Horn Strobe

24fsclsb.wmf
FCPS-24FS Circuit Board

Figure 2.3 NAC Style Y (Class B)

2.2.2 ZNAC-4 Class A Option Module

The ZNAC-4 is an optional Class A conversion module which mounts to connector J3 on the upper
right side of the FCPS-24FS circuit board. This module allows the FCPS-24FS6 or FCPS-24FS8 to
support Style Z (Class A) Notification Appliance Circuits.

Horn Strobes
Alarm Polarity
Shown
ZNAC-4

ZNAC-4 Option Module

J3
24fsclsa.wmf

FCPS-24FS Circuit Board

Figure 2.4 Style Z (Class A) NACs using ZNAC-4 Option Module

16 FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011

Addressable Module Mounting Installation

2.3 Addressable Module Mounting

The FCPS-24FS has been designed to allow the mounting of an addressable control, relay or moni-
tor module on the main circuit board inside the power supply cabinet with the module status LED
visible through the closed door. This allows power to be fed from the FCPS-24FS Auxiliary Power
output directly to the module, if needed, without running the power wires outside the cabinet. As an
example, Figure 2.5 illustrates wiring from the Auxiliary power output terminals to a CMF-300
control module’s terminals 3 (-) and 4 (+).

NOTE: The optional module mounting kit (P/N 90286) is required to install an addressable
module on the power supply main circuit board. The kit includes four female/female and four
male/female standoffs as well as four mounting screws.

*If the SLC device does not match the one in this figure,
refer to the SLC manual wiring conversion charts for leg-
acy and newer versions of the modules.

standoff standoff

standoff standoff

24fsmodltpH.wmf
Module Installation female/female standoffs
1. Remove FCPS-24FS main circuit board from
mounting plate by removing four corner screws.
2. Install four male/female standoffs through bottom of
board in holes indicated in illustration above.
female/female standoffs
3. Screw four female/female standoffs to male ends of
standoffs installed in Step 2 to secure in place.
4. Place addressable module over standoffs installed in mounting screw
Step 3 and secure with supplied screws.
24fsmodinstl.wmf

5. Reinstall main circuit board on mounting plate and addressable module

wire module as show in illustration above.

Figure 2.5 Mounting Module In FCPS-24FS Cabinet

FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011 17

Installation NEC Power-limited Wiring Requirements

2.4 NEC Power-limited Wiring Requirements

Power-limited and nonpower-limited circuit wiring must remain separated in the cabinet. All
power-limited circuit wiring must remain at least 0.25” away from any nonpower-limited circuit
wiring. Furthermore, all power-limited circuit wiring and nonpower-limited circuit wiring must
enter and exit the cabinet through different conduits. One such example of this is shown below.
Your specific application may require different conduit knockouts to be used. Any conduit knock-
outs may be used. For power-limited applications, use of conduit is optional.

AC Power Output Circuits Relay Contacts

Nonpower-limited Power-limited Circuits Nonpower-limited Circuit

Input Circuits
Power-limited Circuit

Specific Application
Power & SLC are
Power-limited Circuits

*If the SLC device does

not match the one in this
figure, refer to the SLC
manual wiring conver-
sion charts for legacy
and newer versions of
the modules.
24fspwrltpH.wmf

Figure 2.5 Power-limited Wiring Example

18 FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011

 Section 3: Programming Options
This section describes the programming options available via DIP switch settings. The FCPS can
be field programmed using option DIP switch SW1 which is located in the lower center of the cir-
cuit board. Refer to the following illustration for switch location and DIP switch placement in the
ON and OFF positions.
Important: Change DIP switch settings only when all power (AC & DC) is removed.

24fsswitc.wmf

Switches 1 through 7 shown

in OFF (Open) position

Switch 8 shown in
ON (Closed) position

Figure 3.1 Field Programming DIP Switches

FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011 19

Programming Options DIP Switch Settings

3.1 DIP Switch Settings

The following table lists the FCPS programmable features and the switch settings required to select
a particular feature. A detailed description of each feature is presented in the following pages.

SW1 DIP Switch ON OFF

1 This switch works in conjunction with switch 2 to determine the Strobe Synchronization Type1.
2 1 OFF, 2 OFF = no sync (steady +24V) - default
1 OFF, 2 ON = System Sensor
1 ON, 2 OFF = Gentex
1 ON, 2 ON = Wheelock
3 FCPS configured for Slave Synchronization FCPS configured for Master Synchronization - default
4 Delay AC Fail Reporting for 2 Hours - default No Delay in AC Fail Reporting
Aux. Trouble Relay responds to all troubles Aux. Trouble Relay responds only to AC Fail/Brownout
Internal Trouble contact responds to AC loss Internal Trouble contact does not respond to AC loss
5 This switch works in conjunction with switch 6 to determine Input to Output functions
6 5 OFF, 6 OFF = General Alarm - default
• FCPS configured as Master (switch 3 OFF), NAC Outputs 1 through 42 are controlled by Control Input #1;
Sync Input is ignored.
• FCPS configured as Slave (switch 3 ON), NAC Outputs 1 through 42 are controlled by Control Input #1;
Sync Input is monitored3.
• Resettable or nonresettable Auxiliary Power Output is available from TB4 Terminals 9 & 10. Control Input
#2 determines if reset will occur (must go from On to Off for a minimum 6 second reset to occur).
• Output #4 function follows DIP switch 8 setting.
5 OFF, 6 ON = Split Alarm
• FCPS configured as Master (switch 3 OFF), NAC Outputs 1 & 2 are controlled by Control Input #1 and
Outputs 3 & 42 are controlled by Control Input #2; Sync Input is ignored.
• FCPS configured as Slave4 (switch 3 ON), NAC Outputs 1 & 2 are controlled by Control Input #1 and
Outputs 3 & 42 are controlled by Control Input #2; Sync Input is monitored3.
• Only nonresettable Auxiliary Power is available from TB4 Terminals 9 & 10.
• Output #4 function follows DIP switch 8 setting.
5 ON, 6 OFF = Split Temporal
• FCPS configured as Master (switch 3 OFF), Control Input #1 controls NAC Outputs 1 & 2 and Control Input
#2 controls Outputs 3 & 42 which will generate a Temporal code signal without sync; Sync Input is ignored.
• FCPS configured as Slave (switch 3 ON), Control Input #1 controls NAC Outputs 1 & 2 and Control Input #2
controls Outputs 3 & 42 which will generate a Temporal code signal without sync; Sync Input is monitored
for Outputs 1 & 23.
• Only nonresettable Auxiliary Power is available from TB4 Terminals 9 & 10.
• Output #4 function follows DIP switch 8 setting.
5 ON, 6 ON = Selective Silence
• FCPS configured as Master (switch 3 OFF), NAC Outputs 1 through 42 are controlled by Control Input #1;
Sync Input is ignored.
• Control Input #2 determines when Selective Silence for all outputs will occur5
• Only nonresettable Auxiliary Power is available from TB4 Terminals 9 & 10.
• Output #4 function follows DIP switch 8 setting.
7 Disable Charger Enable Charger - default
8 Output Circuit #4 = Door Holder Output Circuit #4 = NAC - default

Table 3.1 DIP Switch Settings

1 Strobe Synchronization only works with non-coded NACs.
2 If Door Closer function is selected (switch 8 ON), Output 4 does not function as an NAC, therefore sync input is
ignored for it.
3 If no synchronization is selected by switches 1 & 2, the Sync Input is ignored.
4 When using Split Alarm with power supply configured for Slave Mode, System Sensor cannot be used (use
System Sensor with Master Mode only).
5 Selective Silence allows the silencing of the sounder portion of a horn/strobe combination device without turning
off the strobe.

20 FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011

Programmable Features Description Programming Options

3.2 Programmable Features Description

3.2.1 Synchronization Type Selection
Synchronization is a feature that controls the activation of notification appliances in such a way that
all devices will turn on and off at exactly the same time. This is particularly critical when activat-
ing strobes which must be synchronized to avoid random activation and a potential hazard or con-
fusion. The FCPS can be programmed to operate with a variety of manufacturer’s devices. Note
that strobe synchronization works only with non-coded NACs.
DIP switches 1 and 2 are used to select the type of synchronization as listed below:

DIP Switch 1 DIP Switch 2 Synchronization Type

OFF OFF no synchronization (steady 24V)
OFF ON System Sensor
ON OFF Gentex
ON ON Wheelock

Table 3.2 Sync Type Settings

Maximum Number of Strobes for Synchronization

The total current draw for each Notification Appliance Circuit cannot exceed 3.0 amps. Refer to
the manufacturer’s documentation supplied with the strobes to determine the maximum current
draw for each strobe and ensure that the circuit maximum is not exceeded.
To ensure proper strobe and circuit operation, there is also a limit to the number of strobes that can
be attached to each circuit. Following is a table of the strobes that have been tested with the power
supply and the maximum number that can be connected to each NAC when using the lowest can-
dela settings. Make sure that the NAC maximum current is not exceeded:

Strobe Manufacturer FCPS-24FS6 (max. strobes) FCPS-24FS8 (max. strobes)

System Sensor 51 51
Wheelock 30 40
Gentex 39 39

3.2.2 Synchronization Mode - Master/Slave

The FCPS power supply can be configured for Master or Slave Synchronization by setting DIP
switch 3 ON for Slave or OFF for Master mode.
In some installations, it is necessary to synchronize the flash timing of all strobes in the system for
ADA compliance. Strobes accomplish this by monitoring very short timing pulses on the NAC
power which are created by an FACP with synchronization capability. When installed at the end of
a NAC wire run, this power supply can track (that is follow) the strobe synchronization timing
pulses on the existing NAC wire run. This maintains the overall system flash timing of the addi-
tional strobes attached to this power supply.
When this power supply is configured as a sync generator (Master Synchronization mode), the
Sync Input terminals are not used. The power supply is the originator of the strobe synchronization
pulses on its NAC outputs. In sync generator mode, the sync type (System Sensor, Wheelock, or
Gentex) is selectable via DIP switches 1 and 2.
When this power supply is configured as a sync follower (Slave Synchronization mode), the power
supply’s NAC outputs track the strobe synchronization pulses present at the supply’s Sync Input
terminals. The pulses originate from an upstream FACP or other power supply. Some FACPs pro-
vide synchronization timing pulses from a dedicated sync output connector. Connect the FCPS

FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011 21

Programming Options Programmable Features Description

sync input terminals to the FACP sync output connector instead of the FACP NAC.
Note that the Synchronization Type configured by DIP switches 1 and 2 must be set to the same type
as the signal being fed to the Sync Input circuit in the event that Selective Silence is employed.
Important! In Slave Mode, if the Input is active, but no signal is present on the Sync Input circuit,
the power supply will turn the NACs on steady until a sync signal appears. The NACs will turn off
when the Input becomes inactive.
Also in Slave Mode, if the Input is active and the Sync Input is suddenly lost (FCPS or wiring fail-
ure), there will be a three second period when NAC outputs are indeterminate. After this three sec-
ond period, the power supply will turn the NACs on steady until the Input becomes inactive.

3.2.3 AC Fail Delay/Aux. Trouble Relay Function

The AC Fail Delay feature provides the option to delay generation of a trouble signal upon the loss
of AC power. In addition, the operation of the Aux. Trouble Relay is altered.
• DIP switch 4 set to the ON position will delay the generation of an AC Loss/brownout trouble
signal for 2 hours. In addition, the Aux. Trouble Relay will immediately respond to all trouble
conditions on the power supply.
• DIP switch 4 set to the OFF position will allow the FCPS to generate a trouble signal
immediately on the loss of AC power. In addition, the Aux. Trouble Relay will respond only
to AC power fail/brownout conditions.
Refer to “Supervision of FCPS-24FS Faults” on page 25, for operation of internal NAC trouble
relay in response to AC loss.

3.2.4 Input/Output Function

DIP switches 5 and 6 are used to determine the Input Control circuits that will activate the four out-
put circuits and the function of the output circuits. For example, to configure a General Alarm
operation in which Input Control Circuit #1 activates all four output NACs, DIP switches 5 and 6
are both set to the OFF position. In this configuration, the Sync Input circuit is ignored if the power
supply is set as a Master but will be monitored if the supply is set as a Slave. In addition, if the
Auxiliary Power output is set as a resettable output, the circuit connected to Control Input Circuit
#2 will control the auxiliary power reset function.
The following table details the four possible input/output configurations:
DIP Switch 5 DIP Switch 6 Input/Output Function
OFF OFF General Alarm
• FCPS configured as Master (switch 3 OFF), NAC Outputs 1 through 41 are controlled by
Control Input #1; Sync Input is ignored.
• FCPS configured as Slave (switch 3 ON), NAC Outputs 1 through 42 are controlled by
Control Input #1; Sync Input is monitored2.
• Resettable or nonresettable Auxiliary Power Output is available from TB4 Terminals 9 & 10.
Control Input #2 determines if reset will occur (must go from On to Off for a minimum 6
second reset to occur).
OFF ON Split Alarm
• FCPS configured as Master (switch 3 OFF), NAC Outputs 1 & 2 are controlled by Control
Input #1 and Outputs 3 & 41 are controlled by Control Input #2; Sync Input is ignored.
• FCPS configured as Slave3 (switch 3 ON), NAC Outputs 1 & 2 are controlled by Control
Input #1 and Outputs 3 & 41 are controlled by Control Input #2; Sync Input is monitored2.
• Only nonresettable Auxiliary Power is available from TB4 Terminals 9 & 10.

Table 3.3 Input/Output Configurations

22 FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011

Programmable Features Description Programming Options

ON OFF Split Temporal

• FCPS configured as Master (switch 3 OFF), Control Input #1 controls NAC Outputs 1 & 2
and Control Input #2 controls Outputs 3 & 41 which will generate a Temporal code signal
without sync; Sync Input is ignored.
• FCPS configured as Slave (switch 3 ON), Control Input #1 controls NAC Outputs 1 & 2 and
Control Input #2 controls Outputs 3 & 41 which will generate a Temporal code signal without
sync; Sync Input is monitored for Outputs 1 & 22.
• Only nonresettable Auxiliary Power is available from TB4 Terminals 9 & 10.
ON ON Selective Silence4
• FCPS configured as Master (switch 3 OFF), NAC Outputs 1 through 41 are controlled by
Control Input #1; Sync Input is ignored.
• Control Input #2 determines when Selective Silence for all outputs will occur.
• Only nonresettable Auxiliary Power is available from TB4 Terminals 9 & 10

Table 3.3 Input/Output Configurations

1 If Door Closer function is selected (switch 8 ON), Output 4 does not function as an NAC, therefore sync input is
ignored for Output 4.
2 If no synchronization is selected by switches 1 & 2, the Sync Input is ignored.
3 When using Split Alarm with power supply configured for Slave Mode, System Sensor cannot be used (use
System Sensor with Master Mode only).
4 Selective Silence allows the silencing of the sounder portion of a horn/strobe combination device without turning
off the strobe.

Auxiliary Power Control

The 24 VDC Auxiliary power from TB4 Terminals 9(+) & 10(-) can be resettable or nonresettable
power only when the power supply is configured for General Alarm operation. For all other con-
figurations, the auxiliary power output is only nonresettable.
In the General Alarm configuration, the Auxiliary power output can be made resettable by applying
a steady signal to Control Input 2 (positive 12 to 24 VDC on TB4 Terminal 7 and common on Ter-
minal 8). Temporarily removing the voltage or reversing the polarity will cause the Auxiliary
power output to reset for 6 seconds.

3.2.5 Charger Enable/Disable

The FCPS-FS battery charger can be disabled to accommodate an external battery charger. Setting
DIP switch 7 to the default setting of OFF will enable the battery charger. Setting DIP switch 7 to
the ON position will disable the charger. It should only be disabled if an external battery charger is
being used for the FCPS-FS.

3.2.6 Door Closers

Output Circuit #4 can be configured as an NAC or door closer circuit. Setting DIP switch 8 to the
OFF position will configure Output Circuit #4 as an NAC. Setting DIP switch 8 to the ON position
will configure only Output Circuit #4 as a door closer circuit which will provide a steady 24 VDC
to door holders until an alarm or AC fail condition removes the power following a 10 second delay.

FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011 23

 Notes

24 FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011

 Section 4: Trouble Supervision

4.1 Supervision via FACP Notification Appliance Circuit

4.1.1 Supervision of FACP to FCPS wiring
The FACP (Fire Alarm Control Panel) supervises the connection between itself and the FCPS-24FS
via the control panels NAC End-of-Line Resistor (ELR). The ELR must be installed at the FCPS
end of the circuit, after the last notification appliance on the circuit. If no additional devices are
connected from the FCPS Control Input terminals, the ELR must be connected across terminals 5
& 6 for Control Input Circuit #1 and across terminals 7 & 8 for Control Input Circuit #2. An open
or short anywhere on the control panel’s NAC or power supply NAC will be detected at the FACP
as a NAC trouble.
IMPORTANT: If additional notification appliances are connected to the Out terminals 5 & 6 of
Control Input Circuit #1 or extended from Control Input Circuit #2 Terminals 7 & 8, the ELR must
be installed after the last device on the circuit.

4.1.2 Supervision of FCPS-24FS Faults

The FACP will detect FCPS power supply faults as an open circuit condition on its NAC. An inter-
nal trouble contact is located between TB4 Terminal 3 (In+) and TB4 Terminal 5 (Out+). Any of
the following conditions will cause the trouble contact to open, provided the FACP Notification
Appliance Circuit is not in alarm. The following trouble conditions will cause a general NAC trou-
ble:
• A field wiring fault on the NAC output of the power supply
• An AC fail condition at the power supply (only if SW1 switch 4 is ON and a 2 hour delay has
expired. If SW1 switch 4 is OFF, the Internal Trouble contact will not respond to an AC fail
condition)
• A battery fail condition at the power supply
• A battery charger fail on the power supply
• A ground fault condition on the power supply (zero impedance between power supply and
ground)
Any power supply trouble will break the connection between the FACP and the ELR connected to
Control Input #1 provided the FACP’s NAC is not in alarm. The FACP’s ELR must be placed after
the last notification appliance connected to FCPS terminals 5 & 6 on TB4 or, if no devices are con-
nected to these terminals, the ELR must be connected directly across terminals 5 & 6.
If trouble monitoring is required when the power supply is in alarm, the Trouble Relay at TB5 can
be used for this purpose. An addressable monitor module may be used to monitor these contacts.
Refer to “Aux. Trouble Relay/AC Fail Relay” on page 25 in the following section.

NOTE: Control Input #2 (terminals 7 & 8) cannot be used to supervise the power supply for
internal troubles, but an ELR is still required for FACP wiring supervision.

4.1.3 Aux. Trouble Relay/AC Fail Relay

The FCPS-24FS power supply has one fail-safe Form-C aux. trouble relay located at TB5. The
contacts can be monitored by an FACP input circuit or an addressable monitor module as illustrated
below. The Aux. Trouble Relay responds to FCPS-24FS power supply troubles depending on the
setting of SW1 switch 4.

FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011 25

Trouble Supervision AC Loss Reporting Delay

• With SW1 switch 4 set to the ON position, AC Fail/brownout reporting will be delayed 2 hours
and the following trouble conditions will cause the normally energized Aux. Trouble Relay to
change states regardless of whether the panel is in alarm or standby:
– An AC fail condition at the power supply
– A battery fail condition at the power supply
– A battery charger fail on the power supply
– A ground fault condition on the power supply (zero impedance between the power supply
and ground
– A field wiring fault on the NAC output of the power supply. (If the panel is in alarm, only a
short circuit on the NAC will be detected as a trouble)

NOTE: The NAC Trouble LED will indicate which NAC circuit is in trouble by blinking once for
Circuit 1, twice for Circuit 2, three times for Circuit 3 and four times for Circuit 4. If more than one
circuit is in trouble, the LED will blink the highest circuit number in trouble.

• With SW1 switch 4 set to the OFF position, AC Fail/brownout reporting will occur
immediately and the Aux. Trouble Relay will change state only for AC Fail/brownout
conditions. A monitor module can be used to monitor the relay for AC fail.

SLC

Monitor Module ELR

NO
NC
T7

T6
FCPS-24FS6/8
Aux. Trouble Relay Monitor Module*

*If the SLC device does not

match the one in this figure, refer
to the SLC manual wiring con-
version charts for legacy and
newer versions of the modules.

4.2 AC Loss Reporting Delay

The reporting of AC loss to a central station is usually delayed in order to prevent multiple trans-
missions of AC loss and restoral, thus allowing AC power to stabilize. When a host FACP is pro-
grammed to delay AC loss reporting, the FCPS-24FS must be configured to delay the reporting of
AC fail. This is accomplished by setting SW1 DIP switch 4 to the ON position. This will prevent
AC loss from being reported as a trouble condition for two hours.
Changing the AC Loss Reporting setting will also affect the functioning of the Trouble Relay.
Refer to “Aux. Trouble Relay/AC Fail Relay” on page 25.
Note that the FCPS-24FS power supply will immediately indicate loss of AC power by turning off
the AC Power LED and turning on the Charger Trouble/AC Loss LED, regardless of the setting of
SW1 DIP switch 4.

26 FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011

 Section 5: Applications

5.1 Controlling Four NACs With One Input and Selective

Silence
NOTE: The Relay Module is required only for this application with the power supply set as Master.
If the power supply is set as Slave, the Relay Module is not required. In Slave mode, selective
silence (horn mute) is provided by the FACP through the sync input.

In this application, the power supply has been set as a master with synchronized outputs and selec-
tive silence (see SW1 switch settings in following illustration). All four FCPS-24FS output cir-
cuits, which are shown as NACs (Notification Appliance Circuits), can be controlled from one
input such as an addressable control module as illustrated in Figure 5.1. The control module can be
powered from the FCPS-24FS auxiliary 24 VDC power output (TB4, Terminals 9 & 10) and super-
vised by an EOL relay. An addressable relay module, programmed as an alarm output and a
silenceable point, can be used as a selective silence input.

FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011 27

Applications Controlling Four NACs With One Input and Selective Silence

The control module is shown to demonstrate the use of a remotely mounted device associated with
an addressable fire alarm control panel. The module could be replaced with any circuit capable of
polarity reversal, such as an FACP NAC.

Note: All NACs are supervised and power-limited

Use listed ELR

ELR not required for (4.7K) to terminate
Style Z (Class A) NAC Style Y (Class B)
NAC

Horn/Strobes Horn/Strobes
Alarm Polarity Shown Alarm Polarity Shown

Style Y (Class B)
Style Z (Class A)

Output/NAC 4

24fsapp7tpH.wmf
Internal Trouble Contact
ZNAC-4
Output/NAC 3
Option Module
Output/NAC 2
Output/NAC 1
FCPS-24FS

FCPS-24FS has been set for

Selective Silence and Relay
SW1 Switch Settings
1 & 2 = sync (any setting but OFF/OFF) End-of-Line Resistor Module has been programmed
3 = OFF (master) supplied with Control at FACP as a silenceable point
4 = OFF (no AC Fail reporting delay)
Module so it can perform selective
5 = ON (selective silence) silence when its Normally Open
6 = ON
7 = OFF (charger enabled) contact (8 & 10) closes in
8 = OFF (circuit 4 NAC function) T11 T11 alarm, then opens when silence
T10
T9
T1
T2 SLC T10
T9
T1
T2 SLC is invoked at the FACP.
T8 T3 T8 T3
T7 T4
T5
T7
T6
T4
T5
Note: the Relay Module can be
T6
mounted on the power supply
inside the cabinet. This allows
Relay Module* power wiring to remain inside
Control Module* the cabinet.
EOL Power
*If the SLC device does not match the one in this figure, Supervision Relay
refer to the SLC manual wiring conversion charts for EOLR-1
legacy and newer versions of the modules. (energized)

Figure 5.1 Controlling Four Outputs With One Input

The following notes apply to Figure 5.1 on page 28.

1. When the FCPS-24FS power supply is in an inactive state (control module not active), a
trouble on the power supply will result in an open circuit condition on the control module
output circuit (monitored by End-of-Line Resistor across TB4, Terminals 5 & 6). As an
alternative, the trouble contacts at TB5 of the power supply can also be used for independent
trouble monitoring.
2. The addressable relay module must be programmed as a silenceable point at the FACP to allow
selective silence of horn/strobe devices. The Normally Open contact of the relay module is
connected between TB4 Terminal 7 (IN2 +) and Terminal 9 (Aux. Power +).
3. Do not loop wires under screw terminals. Break wires to maintain proper supervision.
4. An End-of-Line Resistor must be installed between TB4, Terminals 5 & 6 for control module
wiring supervision (the ELR value is dependent on the module employed).

28 FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011

Controlling Three NACs and One Door Holder With One Input Applications

5. Supervise the power wiring between the FCPS-24FS auxiliary 24 VDC output on TB4,
Terminals 9 & 10 with an EOL relay (P/N: EOLR-1).
6. For a list of compatible devices, refer to the Fire•Lite Device Compatibility Document #15384.
7. IMPORTANT! When the power supply is programmed for both Selective Silence and Slave
Mode, TB4 Terminal 7 (IN+) must be jumpered to Terminal 9 (AUX+) and Terminal 8 (IN-)
must be jumpered to Terminal 10 (AUX-). The FACP will control the Selective Silence feature
with this configuration.
If the terminals are not jumpered as indicated, the horn portion of the horn/strobes will be
silenced at all times.

SYNC SYNC IN+ IN- OUT+ OUT- IN2+ IN2- AUX+ AUX-
1 2 3 4 5 6 7 8 9 10
TB4

5.2 Controlling Three NACs and One Door Holder With One
Input
In this application, the power supply has been set as a master with synchronized outputs. All four
FCPS-24FS output circuits, three NACs and one door holder, can be controlled from one input such
as an addressable control module as illustrated in Figure 5.2. The control module can be powered
from the FCPS-24FS auxiliary 24 VDC power output (TB4, Terminals 9 & 10).

FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011 29

Applications Controlling Three NACs and One Door Holder With One Input

The control module is shown to demonstrate the use of a remotely mounted device associated with
an addressable fire alarm control panel. The module could be replaced with any circuit capable of
polarity reversal, such as an FACP Notification Appliance Circuit.
Note: All NACs are supervised and power-limited

ELR not required for

Style Z (Class A) NAC Use listed ELR
(4.7K) to
terminate Style Y
(Class B) NAC
Door Holder
Horn/Strobes
Alarm Polarity Horn/Strobes
Door Holder
Shown Alarm Polarity
Shown

Style Z (Class A)
Style Y (Class B)

Door Holder Circuit 4

Internal Trouble Contact
ZNAC-4 Output/NAC 3
Option Module Output/NAC 2
Output/NAC 1
FCPS-24FS

SW1 Switch Settings

1 & 2 = sync (any setting but OFF/OFF)
3 = OFF (master)
4 = OFF (no AC Fail reporting delay)
SLC 5 = OFF (general alarm)
6 = OFF
End-of-Line Resistor
7 = OFF (charger enabled)
supplied with Control
8 = ON (circuit 4 door holder)
Module

24fsapp6tpH.wmf
Control Module*
*If the SLC device does not match the one in this
figure, refer to the SLC manual wiring conversion
charts for legacy and newer versions of the modules.

Figure 5.2 Controlling Three NACs and One Door Holder With One Input

The following notes apply to Figure 5.2 on page 30.

1. The Output 4 door holder circuit will deactivate 10 seconds after Control Input #1 is activated
or AC power is lost.
2. When the FCPS-24FS power supply is in an inactive state (control module not active), a
trouble on the power supply will result in an open circuit condition on the control module
output circuit (monitored by an End-of-Line Resistor across Terminals 5 & 6). As an
alternative, the trouble contacts at TB5 of the power supply can also be used for independent
trouble monitoring.
3. Do not loop wires under screw terminals. Break wires to maintain proper supervision.

30 FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011

Split Temporal Mode of Operation Applications

4. An End-of-Line Resistor must be installed between terminals 5 & 6 for control module wiring
supervision (the ELR value is dependent on the module employed).
5. For a list of compatible devices, refer to the Fire•Lite Device Compatibility Document #15384.

5.3 Split Temporal Mode of Operation

In this application, the power supply has been set as a master with two synchronized and two non-
synchronized outputs as determined by the Split Temporal mode feature. Control Input #1 (TB4,
Terminals 3 & 4) is connected to an addressable control module which will cause the synchronized

FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011 31

Applications Split Temporal Mode of Operation

power supply output circuits 1 & 2 to turn on. Control Input #2 (TB4, Terminals 7 & 8) is con-
nected to an FACP Notification Appliance Circuit which is used to activate the power supply’s tem-
poral output circuits 3 & 4.

Note: All NACs are supervised and power-limited

ELR not required for

Style Z (Class A) NAC - +
Use listed ELR
(4.7K) to - +
terminate Style Y
- + (Class B) NAC
Bells
- + Bells
- +
TB2 - +
- -
8 -NAC4+
OUT4 TB2
7 -
+ 8

-NAC4+
+

OUT4
7
+

Style Z (Class A) Style Y (Class B)

8
-NAC4+ -NAC3+ -NAC2+ -NAC1+ TB2 AUX TBL Temporal Bell Circuit 4
Internal Trouble Contact 7 OUT4
6
Temporal Bell Circuit 3
OUT3 OUT2

5
ZNAC-4
4
Option Module Horn/Strobe Circuit 2
SYNC IN -
SYNC IN +

3
OUT1+
OUT1-

FCPS-24FS 2
AUX +
AUX -
IN1-

OUT1
IN2+

Horn/Strobe Circuit 1
IN1+

IN2-

J3

1
TB4

3
NO NC COM

1 2 3 4 5 6 7 8 9 10 2
End-of-Line 1
JP3

JP1

TB5

Resistor supplied
JP2

with Control Module

FACP NAC SW1 Switch Settings
SLC End-of-Line 1 & 2 = sync (any setting but
Resistor OFF/OFF)
3 = OFF (master)
T11
T11 4 = OFF (no AC Fail reporting delay)
T10 T1
T10 T1
NAC 5 = ON
24fsapp5tpH2.wmf
T2
T9
T9
T8
T2
T3 Split Temporal
T8
T7
T7
T3
T4
T4
(steady, FACP 6 = OFF
T5
T6
T6 T5
no sync) 7 = OFF (charger enabled)
8 = OFF (circuit 4 NAC)

Control Module*

*If the SLC device does not match the one in this
figure, refer to the SLC manual wiring conversion
charts for legacy and newer versions of the modules.

Figure 5.3 Split Temporal Mode Application

32 FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011

Remote Supply With Resettable and Nonresettable Power Applications

The following notes apply to Figure 5.3 on page 32.

1. When the FCPS-24FS power supply is in an inactive state (control module not active), a
trouble on the power supply will result in an open circuit condition on the control module
output circuit (monitored by an End-of-Line Resistor across Terminals 5 & 6). As an
alternative, the trouble contacts at TB5 of the power supply can also be used for independent
trouble monitoring.
2. Do not loop wires under screw terminals. Break wires to maintain proper supervision.
3. An End-of-Line Resistor must be installed between terminals 5 & 6 for control module wiring
supervision (the ELR value is dependent on the module employed) and across terminals 7 & 8
for FACP NAC wiring supervision (the ELR value is dependent on the NAC).
4. For a list of compatible devices, refer to the Device Compatibility Document.

5.4 Remote Supply With Resettable and Nonresettable Power

The FCPS-24FS can be used as a remote stand-alone power supply to provide power to any devices
that require filtered, resettable or nonresettable power. The FCPS-24FS6 can provide up to 4 amps
of continuous current and the FCPS-24FS8 can provide up to 6 amps of continuous current. The
power supply must be set for Split Alarm mode. Output circuits 1 & 2 are configured as resettable
power outputs by connecting the resettable power from an FACP to Control Input 1 Terminals 3(+)
& 4(-) on TB4 of the FCPS-24FS. Output circuits 3 & 4 are configured as nonresettable power out-
puts by connecting jumpers between the auxiliary 24 VDC output on TB4 to the Control Input 2
terminals on TB4 [Terminals 9(+) to 7(+) and 10(-) to 8(-)].

NOTE: All four outputs can be configured as resettable or all four can be configured as
nonresettable by setting the power supply for General Alarm and then connecting a resettable
power source to Control Input 1 or a nonresettable power source, such as the Aux. Power output
of the FCPS-24FS, to Control Input 1.

FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011 33

Applications Remote Supply With Resettable and Nonresettable Power

For addressable panel applications, an addressable monitor module can be used to monitor the trou-
ble contact of the FCPS-24FS and the resettable power connection from the FACP using an End-of-
Line power supervision relay. If the FCPS-24FS enters a trouble condition, the Normally Closed
trouble contact will open and if the resettable power from the FACP is lost, the Normally Closed
power supervision relay contact will open.

SLC
Power Output 4
Nonresettable
FCPS-24FS
Power Output 3
Nonresettable
Power Output 2
Resettable
Power Output 1
Resettable
T11
T10 T1
T9 T2
T8 T3
T7 T4
T6 T5

End-of-Line Resistor supplied Monitor Module*

with Monitor Module *If the SLC device does
not match the one in this
figure, refer to the SLC SLC
manual wiring conversion
EOL Power charts for legacy and newer
Supervision

24fsapp4tpH.wmf
versions of the modules.
SW1 Switch Settings Relay
24 VDC EOLR-1
Resettable 1 = OFF
Power 2 = OFF No Sync (energized)
3 = OFF (master)
FACP 4 = ON (Aux Trouble Relay responds
to all troubles)
5 = OFF
Split Alarm
6 = ON
7 = OFF (charger enabled)
8 = OFF (circuit 4 NAC)

Figure 5.4 Remote Power Supply Application

The following notes apply to Figure 5.4 on page 34.

1. An End-of-Line Resistor must be installed between TB5, Terminal 1 (trouble relay common)
and the monitor module input circuit for module wiring supervision (the ELR value is
dependent on the module employed).
2. An End-of-Line power supervision relay must be connected between TB4, Terminals 5 & 6.
The Normally Closed (when energized) power supervision relay contact must be in series with
the End-of-Line Resistor referred to in note 1.
3. Do not loop wires under screw terminals. Break wires to maintain proper supervision.
4. For a list of compatible devices, refer to the Fire•Lite Device Compatibility Document #15384.

34 FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011

Master FACP with Slave FCPS-24FS Power Supply Applications

5.5 Master FACP with Slave FCPS-24FS Power Supply

In this application, an FCPS-24FS power supply, configured as a Slave unit, is connected to a mas-
ter FACP programmed for synchronized output. The power supply should be set for synchroniza-
tion which matches the FACP programming.

SW1 Switch Settings

1 & 2 = sync (any setting
Standby Polarity Shown Internal Trouble 8
but OFF/OFF)

-NAC4+ -NAC3+ -NAC2+ -NAC1+ TB2

OUT4
7
Contact 6 3 = ON (slave)

OUT3 OUT2
5
FACP 4 4 = OFF (no AC Fail

SYNC IN -
SYNC IN +
3
reporting delay)

OUT1+
OUT1-

AUX +
AUX -
2

IN2-
IN1+

IN2+
IN1-

OUT1
5 = OFF general alarm

J3
1
FCPS-24FS
6 = OFF

TB4
3

NO NC COM
AUX TBL
1 2 3 4 5 6 7 8 9 10 2
1 7 = OFF (charger enabled)
8 = OFF (circuit 4 NAC)

JP3

JP1

TB5
ELR

JP2
See Note 3

NAC1 -
(programmed
for sync)
+

24fsapp1c.wmf
Figure 5.5a: Supervised Master/Slave Connections (Filtered, Synchronized NAC Source)

SW1 Switch Settings

1 & 2 = sync (any setting
Internal Trouble 8
7
-NAC4+ -NAC3+ -NAC2+ -NAC1+ TB2
OUT4
but OFF/OFF)
Standby Polarity Shown Contact 6
3 = ON (slave)
OUT3 OUT2

5
4
4 = OFF (no AC Fail
SYNC IN -
SYNC IN +

3
FACP
OUT1+
OUT1-

AUX +

reporting delay)
AUX -

2
IN2-
IN1+

IN2+
IN1-

OUT1
J3

1
5 = OFF
TB4

3
NO NC COM

6 = OFF
AUX TBL

1 2 3 4 5 6 7 8 9 10 2
1
7 = OFF (charger enabled)
JP3

JP1

TB5

ELR
JP2

8 = OFF (circuit 4 NAC)

Remote Sync
-
Output
+ 24fsapp1b.wmf

Figure 5.5b: Supervised Master/Slave Connections (Remote Sync Source)

Figure 5.5 Supervised Master/Slave Connections

The following notes apply to both illustrations in Figure 5.5 on page 35

1. Refer to NFPA 72, Chapter 4-4, Visible Characteristics, Public Mode.
2. Use only devices from the same manufacturer in each system.
3. If the FACP has a dedicated sync output connector, wire the remote sync output connector to
the FCPS Sync In terminals TB4 terminals 1 & 2. Refer to the Supervised Master/Slave
Connections (Remote Sync Source) in Figure 5.5b.

FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011 35

Applications Master FCPS-24FS Power Supply Connected to FACP

5.6 Master FCPS-24FS Power Supply Connected to FACP

In this application, a master FCPS-24FS power supply, set for synchronization, is connected to an
FACP with nonsynchronized output.

-NAC4+ -NAC3+ -NAC2+ -NAC1+ TB2

OUT4
Internal Trouble 7
Contact 6

OUT3 OUT2
Standby Polarity Shown 5
4

SYNC IN -
SYNC IN +
3

OUT1+
OUT1-
FACP

AUX +
AUX -
2

IN2-
IN1+

IN2+
IN1-

24fsapp11b.wmf
OUT1
J3
FCPS-24FS 1

TB4
3

NO NC COM
AUX TBL
1 2 3 4 5 6 7 8 9 10 2
1
NAC with no

JP3

JP1

TB5
syncronization

JP2
ELR for
- FACP
SW1 Switch Settings
1 & 2 = sync (any setting
NAC1 NAC
but OFF/OFF)
+ 3 = OFF (master)
4 = OFF (No AC Fail
Reporting Delay)
5 = OFF general alarm
6 = OFF
7 = OFF (charger enabled)
8 = OFF (circuit 4 NAC)

Figure 5.6 Supervised FACP to Master Connections (nonsynchronized source)

The following notes apply to this illustration

1. Refer to NFPA 72, Chapter 4-4, Visible Characteristics, Public Mode.
2. Use only devices from the same manufacturer in each system.

5.7 Canadian Applications

Canadian applications, per ULC, require the following:
• The FCPS-24FS power supply must be used as a Notification Appliance Circuit extender only.
The TB2 terminals cannot be configured as auxiliary power outputs.
• The host FACP must monitor for all ground fault conditions. The Ground Fault Detection
circuit on the FCPS-24FS power supply must be disabled by cutting jumper JP1.

36 FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011

Canadian Applications Applications

• The negative (-) battery terminal of the FCPS-24FS power supply must be connected to the
negative (-) battery terminal of the host FACP.

NAC Outputs only

Cut JP1

24fsCanadiantpH.wmf
Battery - Battery -

FCPS Power Supply Host FACP

*If the SLC device does not match the one in this figure, refer to the SLC man-
ual wiring conversion charts for legacy and newer versions of the modules.

FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011 37

 Section 6: Power Supply Requirements

6.1 Overview
This section contains instructions and tables for calculating power supply currents in alarm and
standby conditions. This is a four-step process, consisting of the following:
1. Calculating the total amount of AC branch circuit current required to operate the system
2. Calculating the power supply load current for non-fire and fire alarm conditions and
calculating the secondary (battery) load
3. Calculating the size of batteries required to support the system if an AC power loss occurs
4. Selecting the proper batteries for your system

6.2 Calculating the AC Branch Circuit

The power supply requires connection to a separate, dedicated AC branch circuit, which must be
labeled FIRE ALARM. This branch circuit must connect to the line side of the main power feed
of the protected premises. No other non-fire alarm equipment may be powered from the fire alarm
branch circuit. The branch circuit wire must run continuously, without any disconnect devices,
from the power source to the power supply. Overcurrent protection for this circuit must comply
with Article 760 of the National Electrical Codes as well as local codes. Use 14 AWG (2.00 mm2)
wire with 600 volt insulation for this branch circuit.
Use Table 6.1 to determine the total amount of current, in AC amperes, that must be supplied to the
system.

Number of Current Draw Total Current

Device Type
Devices (AC amps) per Device

FCPS-24FS6/8(C) 3.2
or 1 x or =
FCPS-24FS6/8E 1.6

[ ] [ ] x [ ] =

[ ] [ ] x [ ] =

Sum Column for AC Branch Current Required =

Table 6.1 120/240 VAC Branch Circuit Requirements

38 FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011

Calculating the System Current Draw Power Supply Requirements

6.3 Calculating the System Current Draw

6.3.1 Overview
The power supply must be able to power all internal and external devices continuously during the
non-fire alarm condition. To calculate the non-fire alarm load on the power supply when primary
power is applied, use Calculation Column 1 in Table 6.3 on page 40. The power supply must sup-
port a larger load current during a fire alarm condition. To calculate the fire alarm load on the
power supply, use Calculation Column 2 in Table 6.3 on page 40. The secondary power source
(batteries) must be able to power the system during a primary power loss. To calculate the non-fire
alarm load on the secondary power source, use Calculation Column 3 in Table 6.3 on page 40.
When calculating current draw and the battery size, note the following:
• Primary refers to the main power source for the power supply.
• Secondary refers to the power supply’s backup batteries.
• All currents are given in amperes (A). Table 6.2 shows how to convert milliamperes and
microamperes to full amperes.

To convert... Multiply Example

Milliamperes (mA) to mA x 0.001 3 mA x 0.001 = 0.003 A

amperes (A)

Microamperes (A) to A x 0.000001 300 A x 0.000001 = 0.0003 A

amperes (A)

Table 6.2 Converting to Full Amperes

6.3.2 How to Calculate System Current Draw

Use Table 6.3 on page 40 to calculate current draws as follows:
1. Enter the quantity of devices in all three columns.
2. Enter the current draw where required. Refer to the Fire-Lite Device Compatibility Document
for compatible devices and their current draws.
3. Calculate the current draws for each in all columns.
4. Sum the total current for each column.
5. Copy the totals from Column 2 and Column 3 to Table 6.3 on page 40.
Following are the types of current that can be entered into Table 6.3 on page 40.
 Calculation Column 1 - The primary supply current load that the power supply must
support during a non-fire alarm condition, with AC power applied
 Calculation Column 2 - The primary supply current load the power supply must support
during a fire alarm condition, with AC power applied
 Calculation Column 3 - The standby current drawn from the batteries in a non-fire alarm
condition during a loss of AC power

FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011 39

Power Supply Requirements Calculating the System Current Draw

Table 6.3 contains three columns for calculating current draws. For each column, calculate the cur-
rent and enter the total (in amperes) in the bottom row. When finished, copy the totals from Calcu-
lation Column 2 and Calculation Column 3 to Table 6.4 on page 41.

Calculation Column 3
Calculate Column 1 Calculate Column 2
Secondary, Non-Fire Alarm
Device Type Primary, Non-Fire Alarm Current Primary, Fire Alarm Current
Current
(amps) (amps)
(amps)

Qty X (current draw) = Total Qty X (current draw) = Total Qty X (current draw) = Total

Main Circuit 1 X [ 0.091] = 1 X [ 0.145] = 1 X [ 0.065] =

Board

Power [ ] X [ 0.025] = [ ] X [0.025 ] = [ ] X [ 0.025] =

Supervision Relay

NAC/Output #1 [ ] X[ ]=

NAC/Output #2 [ ] X[ ]=

NAC/Output #3 [ ] X[ ]=

NAC/Output #4 [ ] X[ ]=

Current Draw [ ]= [ ]= [ ]=
from TB4
Terminals 9 & 10

Sum each Primary Non-Alarm = Primary Alarm = Secondary Alarm =

column for totals

Table 6.3 System Current Draw Calculations

40 FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011

Calculating the Battery Size Power Supply Requirements

6.4 Calculating the Battery Size

Use Table 6.4 to calculate the total Standby and Alarm load in ampere hours (AH). This total load
determines the battery size (in AH) required to support the power supply under the loss of AC
power. Complete Table 6.4 as follows:
1. Enter the totals from Table 6.3 on page 40, Calculation Columns 2 and 3 where shown.
2. Enter the NFPA Standby and Alarm times. Refer to Section 6.4.1, “NFPA Battery
Requirements”.
3. Calculate the ampere hours for Standby and Alarm, then sum the Standby and Alarm ampere
hours.
4. Multiply the sum by the derating factor of 1.2 to calculate the proper battery size (in AH).
5. Write the ampere hour requirements on the Protected Premises label located inside the cabinet
door.

Secondary Standby Load Required Standby Time = AH

(total from Table 6.3 Calculation (24 or 60 hours)
Column 3)
[ ] X[ ]

Primary Alarm Load Required Alarm Time = AH

(total from Table 6.3 Calculation (for 5 min., enter 0.084,
Column 2) for 10 min., enter 0.168)
[ ] X[

Sum of Standby and Alarm Ampere Hours = AH

for nonULC applications, multiply by the Derating Factor1 X 1.2

for ULC applications, multiply by the Derating Factor1 X 2.5

Battery Size, Total Ampere Hours Required = AH

Table 6.4 Total Secondary Power Requirements at 24 VDC

1 Multiply by only one of the Derating Factors, depending on whether the power
supply is being used for a ULC (Canadian) application or nonULC application.

6.4.1 NFPA Battery Requirements

NFPA 72 Local and Proprietary Fire Alarm Systems require 24 hours of standby power followed by
5 minutes in alarm.

6.4.2 Selecting and Locating Batteries

Select batteries that meet or exceed the total ampere hours calculated in Table 6.4. The power sup-
ply can charge batteries in the 7 AH to 18 AH range. The power supply cabinet is capable of hous-
ing batteries up to 7 AH. Batteries larger than 7 AH require the BB-17F or other UL listed external
battery cabinet.

FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011 41

 Notes

42 FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011

 Appendix A: Wire Requirements
Connecting external system accessories to the main circuits must be carefully considered to ensure
proper operation. It is important to use the correct type of wire, gauge and run length for each cir-
cuit. The following table lists NAC wiring requirements for the FCPS-24FS6 and FCPS-24FS8
Field Charger Power Supply.

Max. CLASS-B CLASS-A

allowable Max. allowable wire pair lenth Max. allowable wire pair length
NAC Load (feet) (feet)
total loop
(Amps)
resistance AWG 12 AWG 14 AWG 16 AWG 18 AWG 12 AWG 14 AWG 16 AWG 18
(ohms) solid solid solid solid solid solid solid solid
0.25 6.00 1554 977 613 386 777 489 307 193
0.5 3.00 777 489 307 193 389 244 153 97
0.75 2.00 518 326 204 129 259 163 102 64
1.0 1.50 389 244 153 97 194 122 77 48
1.25 1.20 311 195 123 77 155 98 61 39
1.5 1.00 259 163 102 64 130 81 51 32
1.75 0.86 222 140 88 55 111 70 44 28
2.0 0.75 194 122 77 48 97 61 38 24
2.25 0.67 173 109 68 43 86 54 34 21
2.5 0.60 155 98 61 39 78 49 31 19
2.75 0.55 141 89 56 35 71 44 28 18
3.0 0.50 130 81 51 32 65 41 26 16

Table A.1 NAC Wiring Requirements for Power Supply

NOTE: Calculations are based on Direct-Current Resistance data for uncoated copper wire, per
National Electrical Code (2005 Edition) Table 8, Conductor Properties.

FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011 43

 Index
A Class A Converter Module 16
see also ZNAC-4 8
AC
Class B
Loss 8
see also Style Y 8
Loss Reporting Delay 26
Coded Input 10
AC fail
delay 22 Coded/Noncoded Input Selection 10
coding
see also AC loss reporting delay 22
NAC 8
AC loss
reporting delay 22 compatibility
input circuit 8
AC loss reporting
delay 9 control circuit 8
current 11
AC power 10
see also input circuit 11
current 10
voltage 11
LED 10
current
voltage 10
maximum continuous 9
activation
reverse polarity 8 maximum short term 9
standby 11
alarm condition 8
total continuous 11
applications 8
total short term 11
Auxiliary Power 9, 11
current 11
voltage 11 D
Auxiliary Power Control dimensions
see also resettable or nonresettable power backbox 15
23
E
B ELR
backbox dimensions 15 installation 25
battery see also End-of-Line Resistor 25
capacity 11 End-of-Line Resistor
charge current 11 see also ELR 25
charger capacity 9
float charge voltage 11
fuse F1 11
F
lead acid 9, 11 faults 25
maximum capacity 9 FCPS-24FS6 8
see also secondary power 11 FCPS-24FS8 8
trouble 8 Features 8
battery/charger trouble LED 10 filtered power 8
float charge voltage 11
Form-C
C see also Relay 9
cabinet
see also backbox 15
capacity
G
battery 11 ground fault 8
charge current ground fault detection 9, 10
maximum 11 Jumper JP1 10
charger trouble 8 ground fault LED 10
LED 10
circuit board I
layout 12 input

44 FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011

Index J–T

current 11 O
voltage 11
output
input circuit 8
circuit types 11
activation 8
maximum current 3.0 amps 11
compatibility 8
output circuit
see also control 11 current 11
installation 14
maximum current 8
see also NAC output 11
J Style 11
JP1 Jumper voltage rating 11
ground fault detection 10 output power 8
JP2 Jumper
Coded/Noncoded Input 10 P
JP3 Jumper
Power
Coded/Noncoded Input 10
nonresettable 8
Jumper
resettable 8
JP1 ground fault detection 9, 10
power supply
JP2 Coded/NonCoded Input 10 board layout drawing 12
JP3 Coded/Noncoded Input 10
connectors and jumpers 12
power supply requirements 38
L powering supply 38
LED power-limited 8
AC power 10 power-limited wiring 18
battery/charger trouble 10
Charger Trouble 10 R
Ground Fault 10
relay
NAC Trouble 10
trouble 8, 9, 11, 25
LED indicators 10
reporting delay
AC loss 26
M resettable power 23
mounting
see also installation 14 S
secondary power
N see also battery 11
NAC Special Application Power
activation 8 see also Auxiliary Power 11
coding 8 specifications 10
see also Notification Appliance Circuit 8 Startup Procedure 9
supervision 25 strobe synchronization 9
NAC Circuit Wiring 16 Style
NAC output see also NFPA Style 8
see also output circuit 11 Style Y
NAC style see also Class B 8
see alsoNFPA Style 8 supervision 8
NAC Trouble LED 10 NAC 25
NACs 9 trouble 25
NEC power-limited wiring requirements 18 synchronization
NFPA Style ADA compatible 8
see also Style 8 selectable 9
nonalarm state 8
Noncoded Input 10 T
nonresettable power 23
trouble
Notification Appliance Circuit supervision 25
see also NAC 8
trouble relay 8, 9, 11, 25

FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011 45

W–Z Index

contact rating 11
trouble supervision 8
troubles 25
power supply 8

W
wiring 9
AC power 10
power-limited 18

Z
ZNAC-4 16
see also Class A Converter Module 8

46 FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011

 Manufacturer Warranties and Limitation of Liability
Manufacturer Warranties. Subject to the limitations set forth herein,
Manufacturer warrants that the Products manufactured by it in its
Northford, Connecticut facility and sold by it to its authorized
Distributors shall be free, under normal use and service, from defects
in material and workmanship for a period of thirty six months (36)
months from the date of manufacture (effective Jan. 1, 2009). The
Products manufactured and sold by Manufacturer are date stamped at
the time of production. Manufacturer does not warrant Products that
are not manufactured by it in its Northford, Connecticut facility but
assigns to its Distributor, to the extent possible, any warranty offered
by the manufacturer of such product. This warranty shall be void if a
Product is altered, serviced or repaired by anyone other than
Manufacturer or its authorized Distributors. This warranty shall also
be void if there is a failure to maintain the Products and the systems in
which they operate in proper working conditions.
MANUFACTURER MAKES NO FURTHER WARRANTIES, AND
DISCLAIMS ANY AND ALL OTHER WARRANTIES, EITHER
EXPRESSED OR IMPLIED, WITH RESPECT TO THE PRODUCTS,
TRADEMARKS, PROGRAMS AND SERVICES RENDERED BY
MANUFACTURER INCLUDING WITHOUT LIMITATION,
INFRINGEMENT, TITLE, MERCHANTABILITY, OR FITNESS FOR
ANY PARTICULAR PURPOSE. MANUFACTURER SHALL NOT BE
LIABLE FOR ANY PERSONAL INJURY OR DEATH WHICH MAY
ARISE IN THE COURSE OF, OR AS A RESULT OF, PERSONAL,
COMMERCIAL OR INDUSTRIAL USES OF ITS PRODUCTS.
This document constitutes the only warranty made by Manufacturer
with respect to its products and replaces all previous warranties and is
the only warranty made by Manufacturer. No increase or alteration,
written or verbal, of the obligation of this warranty is authorized.
Manufacturer does not represent that its products will prevent any loss
by fire or otherwise.
Warranty Claims. Manufacturer shall replace or repair, at
Manufacturer's discretion, each part returned by its authorized
Distributor and acknowledged by Manufacturer to be defective,
provided that such part shall have been returned to Manufacturer with
all charges prepaid and the authorized Distributor has completed
Manufacturer's Return Material Authorization form. The replacement
part shall come from Manufacturer's stock and may be new or
refurbished. THE FOREGOING IS DISTRIBUTOR'S SOLE AND
EXCLUSIVE REMEDY IN THE EVENT OF A WARRANTY CLAIM.

Warn-HL-08-2009.fm

FCPS-24FS Series Instruction Manual — P/N 51883:H1 4/14/2011 47

 World Headquarters
1 Firelite Place
Northford, CT 06472-1653 USA
203-484-7161
fax 203-484-7118

www.firelite.com