RECTIFIER
PSR327
In: 230VAC
Out: 220VDC (2.7kW)
· Single-phase module 1/4 x 19’’, 3U Power supply modules of series PSR327 are com-
pact battery charging rectifiers with an optimized
with sinusoidal input current (PFC) switching principle and therefore with a very high
power density. The rectifier can be used in all DC
· Input overvoltage protection applications with or without battery.
· “Hot plug-in“ design with backplane Due to the modular concept and a high scalability
the user is able to equip the power supply with
connection
additional modules according to his actual power
· High power density profile. The chargers are very user friendly and can
be swapped and upgraded during operation.
· CAN-Bus interface
The devices get their operation parameters via
· Integrated decoupling from the DC bus the system wide CAN communication bus. After a
successful login a central monitoring unit controls
· Front-to-rear airflow with temperature- and monitors the devices. In case of CAN-Bus in-
terruption the modules operate continuously with
controlled fan cooling internal default values. The current sharing bet-
· Suitable for Pb and NiCd batteries ween the rectifier modules operates independent
of the CAN communication bus. Up to 4 modules
can be integrated in a 19” sub rack with 3U
(216V/50A).
DC power supply facilities with or without battery in
all areas of industry, power generation and power
distribution.
Type PSR327/220-12.5
Article code 101-027-188.00
Nominal input voltage 230VAC ±20%
Nominal input current 12.9AAC
Input frequency range 47-63Hz
Power factor >0.99 at Pnom >50%
Total harmonic distortion <5%
Efficiency ≥91%
Internal input fusing 16A (6.3x32mm)
Nominal output voltage 216VDC
Nominal output current @ 216V 12.5ADC
Nominal output power 2.7kW
Charge characteristic IV characteristic according to DIN41772/DIN41773; power limited
Adjustable output voltage range 170 - 295VDC
Default value of the charging voltage (factory set) 245.2VDC (2.27V/cell; lead acid battery); over CAN dongle settable for NiCd batteries
Output over voltage Vo> (factory set) 270VDC (2.5V/cell; lead acid battery); over CAN dongle settable for NiCd batteries
Voltage ripple ≤200mVpp
Dynamic accuracy of the charging voltage <3% Vnom at load changes between 10%-90%-10% Inom; transient time ≤1.5ms
Short circuit protection Continuously short circuit proof; 1x Inom
Parallel operation Yes; current sharing ≤10% Inom
Internal decoupling at the output Yes, in the positive output line
Internal output fuse 20A
LED signalling Operation (green), Vo OK (green), Vo> (red), Alarm (red)
Main processor 16Bit Fujitsu
Isolated signalling contacts “General fault”; relay COM/NO/NC, maximum contact load: 60VDC/500mA
Communications interface CAN-Bus, proprietary protocol
Ambient temperature Operation: -20°C to +55°C, storage: -40°C to +85°C
Cooling Fan cooling (temperature-controlled, r.p.m.-monitored)
Climatic conditions according to IEC 721-3-3 class 3K3/3Z1/3B1/3C2/3S2/3M2
Max. installation altitude ≤ 1500m
Audible noise <45dB (A)
Type of construction 1/4 x 19’’, 3U
Dimensions (W/H/D) 106.3/133/326.5mm
Weight approx. 3.9kg
Type of enclosure / Protection class IP20 (front panel) / 1
Colour Front panel: RAL 7035, neutral, black print RAL 9005
CE conformity yes
Compliance to safety standards EN60950-1; VDE0100 T410; VDE0110; EN50178; EN60146
Compliance to EMC standards EN55022/24 (ITE), class “A“; EN61000-4 T2-5
Electrical connector AC input, DC output and signalization: DIN41612-M-connector
Article code View Designation
102-327-318.HV01 Assembly set 19” sub rack 3U incl.
backplane for 3 pcs. rectifiers
PSR327/220 V and 1pcs. DC control-
ler UPC3-220 V; connection board
DCC-CB1 included in delivery.
102-327-408.HV01 Assembly set 19“ sub rack 3U incl.
backplane for 4 pcs. rectifiers
PSR327/220 V
301-003-898.02 Monitoring, controlling and signal-
ling unit (DC controller) UPC3-220 V
302-DCC-CB1.00 Connection board, necessary to
connect all measuring, control and
signalling wires over the sub rack to
the UPC3 (MSTB screw terminals)
(Spare part)
881-MEC-BPL.03.21.B Cover plate (with handle) to cover
not used PSR slots, 1/4 x 19’’, 3U;
RAL 7035
880-CAN-DNG.00 CAN dongle, supplied over CAN-Bus,
12V, incl. software
DS_PSR327_220V_2009_E_R01 - Subject to change without notice - Eltek Valere Industrial GmbH
