Scribd
Upload
618 views3 pages

Welding Procedure Specification

1) This document provides a welding procedure specification for manual shielded metal arc welding (SMAW) of butt, tee, and lap joints in A-36 steel from 4.8mm to 38mm thick. 2) The filler metal is E7018 electrode with a diameter of 3.2mm. Welding parameters are 110-140 amps and 22-26 volts. Travel speed is 6-12 cm/min for the root and hot passes and fill and cap. 3) Joint preparation includes machining and grinding. Backing is allowed but not required. There are no preheat or post weld heat treatment requirements.

Uploaded by

Mark Jason M. Brual
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
618 views3 pages

Welding Procedure Specification

1) This document provides a welding procedure specification for manual shielded metal arc welding (SMAW) of butt, tee, and lap joints in A-36 steel from 4.8mm to 38mm thick. 2) The filler metal is E7018 electrode with a diameter of 3.2mm. Welding parameters are 110-140 amps and 22-26 volts. Travel speed is 6-12 cm/min for the root and hot passes and fill and cap. 3) Joint preparation includes machining and grinding. Backing is allowed but not required. There are no preheat or post weld heat treatment requirements.

Uploaded by

Mark Jason M. Brual
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 3

Sheet 1 of 3 (WPS)

PRE’D M.J.M.BRUAL
CHK’D R.V.CONTRERAS
APP’D R.C.GUICO
WELDING PROCEDURE SPECIFICATION

WPS No. NPMSI -016 Rev. 0 DATE 13-JUNE-2019


Rev. 1 DATE. 9-SEPT-2019
Supporting PQR No. NPMSI-017
Welding Process (es) SMAW Type Manual
JOINTS

Joint No. Joint Design: Butt, Tee, Lap


Backing Yes No. Detail of joint Design
Backing Material N/A
Method of Fit Up Refer on page 3 ( See page 3 of 3 )
Edge Preparation Machining & Grinding
Other None
BASE METAL

P. NO. 1 Group No. 1 to P. No. 8 Group No. 1


Specification Type & Grade A-36 to A-36
Thickness Range:
Groove 4.8mm to 38mm
Fillet Unlimited to
Pipe Dia. Range: N/A to
Max. Pass Th’k. Limit 12mm to
Other None
POSITION

Position of Groove ALL


Welding Progression: Up Down
Position of Fillet ALL
Other None

FILLER METAL

F. No. 4 /
A. No. 1 /
Spec No. (SFA) SFA 5.1 /
AWS No. (Class) E 7018 /
Deposited Weld Metal:
Thickness Range: Groove 38mm
Fillet Unlimited
Electrode Flux (Class) N/A
Brand Name of Flux
WELDING PROCEDURE SPECIFICATION Sheet 2 of 3 (WPS)

PREHEAT: Yes No POST HEAT: Yes No

Preheat Temp. Ambient Post heat Temp. Not required


Interpass Temp Not required. Holding Time Not required
Method N/A Method Not required
Other None Other None
POSTWELD HEAT TREATMENT: Yes No

Temperature Range Not required


Holding Time N/A
Increasing & Decreasing Rate Not required
Other None
GAS

Shielding Gas (es) No Flow Rate N/A


Percent Composition 99.99% Gas Backing NO_n/ __
Increasing & Decreasing Rate N/A
Other None
ELECTRICAL CHARACTERISTIC & TECHNIQUE

Tungsten Electrode Size N/A Type N/A


Mode of Metal Transfer for GMAW N /A
Electrode Wire Feed Speed Range N/A
Bead: String Weave Orifice or Gas Cup size N /A
Initial & Interpass Cleaning: SS Brushing Grinding Other
Pass (per side): Multi Single Electrode: Multi Single
Method of Back Gouging N/A
Other None
Filler Metal Current Travel Speed
Weld Welding Class Dia. Type Amp. Volt Range Remarks
Layer Process mm Polar Range Range (cm/min)

1 to 2 SMAW E7018 3.2mm DCRP 110-140 22-26 6-12 Root to Hot pass

22-26 6-12 Fill & Cap


3 to Cap SMAW E7018 3.2mm DCRP 110-140

Prepared by: Checked by: Approved by: JGSPC

_Mark Jason M. Brual__ Ruel V. Contreras Ronnie Guico_______


QA/QC Inspector Project Manager NPMSI President CEO
WELDING PROCEDURE SPECIFICATION Sheet 3 of 3

You might also like