Solid State Relay(SSR)
What is SSR?
SSR = Solid State Relay, the main job of SSR is switching
higher-quality AC, or AC load using low DC Voltage .SSR
relay switch off and on thousand times speed where
normal relay can do only for some times .
Employ semiconductor switching elements-thyristors,
triacs, diodes, transistors & optical semiconductors called
photocouplers to isolate input and output signals.
Features of SSR
• Enable high-speed and high-frequency switching
• Unlimited number of switching operations
• Consist of semiconductors, so there is no contact
Operation of SSR
• Use a control circuit and a separate circuit for
switching the load
• When voltage is applied to the input of the SSR, the relay is
energized by a light-emitting diode
• The light from the diode is beamed into a light-
sensitive semiconductor
• In case of zero-voltage crossover relays, semiconductor
conditions the control circuit to turn on the output SSR at
the next zero-voltage crossover
• In case of nonzero-voltage crossover relays, the
output SSR is turned on at the precise voltage
occurring at the time
Structure of SSR
• Comprised of different kinds of semiconductor materials
• Consist of Transistors, LED, Resistor, Thyristors,
Capacitor etc
Hardware Connection of single phase SSR
Solid state relay widely used in industry to control
high switching load like heater. Pin 3 & 4 input
terminal. Suppose 24VDC is supplied to the terminal
3 & 4 then solid state relay energized. Pin 1 & 2
normally open contact is output terminal. This solid
state relay turn ON only AC load. Suppose 220VAC is
connected to pin 1. Pin 2 is connected to a 220VAC
light. Another terminal of light is connected to
neutral. When 24VDC is supplied to the input
terminal through a push switch then output NO
contact becomes NC and turns ON the light. Keep in
mind that, this solid state relay only turn ON AC load
notDC.
General Specification
• Input Voltage: 4~32 VDC
• Turn Off Voltage: <3.5 VDC
• Trigger Current: 12 mA(max)
• Control Method: Zero Cross
• Leakage Current: 5 mA(max)
• Response Time: 8.3 ms(60Hz)
• Input Immunity: 2KV
• Isolation Strength: 4kVms
• Housing Material: ABS
• Circumstance: -40⁰C ~ +80⁰C: 35~85%RH
SSR by IAEC
Imported From: FOTEK Controls Co. Ltd. Mainly
3 types of SSR is imported
1. ESR Series 2. SSR Series
ESR-25DA SSR-25DA
SSR-40DA
SSR-50DA
3. TSR Series SSR-75DA
TSR 40DA SSR-75LA
TSR 75DA
Model Guiding
SSR - 40 D A H R
Product: Input Output Output Control
Output
SSR=Single Method: Voltage: Voltage Method:
Current:
Phase Solid D=4~32 VDC A=AC Volt Range: R=Rando
10=10A
State Module L=4~20 mA D=DC Volt H=High m
25=25A
TSR=Three 40=40A Voltage Control
Phase Solid 50=50A Type Type
State Module 75=75A Blank= Blank=
ESR=Three Standard Zero
Phase High Type Cross
Power Solid Control
State Module Type
ESR-25DA
• High Power
Three Phase Solid
State Module
• Load Voltage:
24~380VAC
• Terminal Type
SSR-25DA SSR-40DA
Single Phase Solid State Module Single Phase Solid State Module
Terminal Type Terminal Type
Rated Current: 25A Rated Current: 40A
Surge Current: 275A Surge Current: 410A
SSR-50DA SSR-75DA
Single Phase Solid State Module Single Phase Solid State Module
Terminal Type Terminal Type
Rated Current: 50A Rated Current: 75A
Surge Current: 550A Surge Current: 820A
SSR-75LA TSR-75DA
Single Phase Solid State Module Three Phase Solid State Module
Terminal Type Terminal Type
Rated Current: 75A Rated Current: 75A
Surge Current: 820A Surge Current: 820A
TSR-40DA
Three Phase Solid
State Module
Terminal Type
Rated Current: 40A
Surge Current: 410A
