[B.] oe Beta Three Norm Series Multi-channel power amplifier 2 enannelsATTENTIONS A The product complies with standard safety regulations. Incorrect operations may cause fire or electric shock. Please follow strictly the operation steps for device installation and repair. A. Be ware of high voltage in the device, do not open the chassis. > Do not touch the output terminals marked with 4 when the device is on working condition. Keep good cooling. The ventilation shall not covered and blocked by any objects. For rack n, make sure there is at least 10 cm space away from the venti Do not insert any metal parts or inflammable objects to the device due to high risk of electric shock and fire. Do not expose the device to rain or at high humidity places. Do not put any sundries onto the device. Make sure to use the same components to do repair or replacement for the ones marked with & Make sure the local voltage is in compliance with the device. Select suitable impedance, do not work overload for long time. Take off power plug from mains when the device is not used for long PrP rr PrP bP Pb Please consult local dealers or technicians to do repair works. ™ SYMBOLS: The equilateral triangle with lightning bolt warns the user of dangerous voltage levels localized within the cabinet. The equilateral triangle with exclamatory mark means the important operation in the user's manual. This is a patented product, please respect the Intellectual Property Law.CATALOGUE 1, Introduction P41 "2. Parameters p2 3, Installation P3 4, Front panel P4 5, _ Indicators on front panel P4 6, _Rearpanel P5 7, Power supply P7 8, Input/Output connectors P7 9, Function setup and cable connection P8 10, Operations P9 11, Protection and the cooling system P9 12, Troubles and trouble shootings P10 13, Safety attentions Pi ‘Manufacturer reserves rights for any product upgrade. Please be understandable thal the ‘new information does not be informed in time. Pictures in the manual are for reference only, all details are subject to the real product-M= x 7p) tts enc al Fer Lf } 1. INTRODUCTION £ Thanks for selecting our product. poten Ga Maxima aa Norm series multi-channel professional amplifier is designed with a stable and high officiont structure for thermal dissipation. The design adopts advanced simple output circuit along with precise detection and protection that achieve superior stability. The innovative temperature control and MF adjustment make Norm series also a more efficient performance. i The standardization and diversification of Norm series fully meet the different requirements of PA sound reinforcement. The various connectors and simple controls ensure more application convenience. Features: ‘© Multiple power levels / channels for flexible system installations. © Versatile ways to set up: channel input link-» power output. © Innovative MF adjustment to control the distortion of middle frequency when the amplifier iC |. works on big output. 3 ¥y # Low distortion, low noise, high-speed driving for amplification to make powerful and ~ | S © clean sound. a * {The advanced heat management system ensures efficient cooling and all heating J 8 t ‘components are working in a stable way. & ~ “D~ © Clearindicators and touch-proof volume knobs on the front panel. f% < © easy to disassemble the chassis fordust cleaning. & = SO nm T~ .” Norm series is built to be putinto the most tough situation to drive sound reinforcement, ‘with its high reliability, long product life, and severe circuit protections being considered = > = bythe manufacturer. <— Please read carefully the user's manual the chapters for input, output, and power ae a ~ connection Read completely the manual to know best asviees or prot parang > ; and use high performance of your products. z, WANG 28. a (oe(wus Lypepn|>u ajpuey)uwogE x wMESy x mNIES 0.08 ~ 0,S2- eanyeradwiay aBes03s 5 0p~2,01- aunvesadwiay Bupjiom 5 wIKXb SUL EIX BIKE neu, BKX? soypauu0> nduy ____#HO9/2HOs AOzL-001 3¥ | surert 3Peq 011401) wo4y Mose ‘paeds ue} ajqelseR | Suyjoo sed burping cr + Fan sod Buipuiae+ rN no 9804 | spppeuv0> nding o40z< Indus pasuejeq yAOL HPNE AP SPPUREL anoz-rHoe apsot> Ly ZH4Z/ZHO9" 5 B® %S0'O> e023 2HO2' BO %SZ0'O> 601 | By9L Syst | Syst | SxvL Saxe xz, | Bxct MOO! | MOoST ‘mooot | moost T woo5 | ‘mooot | moss ‘Moss moost een TE HI Sitemfoone= 0° ‘moss. ‘moot | moss moss mosv @@HD| ‘ool moss ‘M009 Mow 009 mow ‘moos | Moov ss9yuidwe jauuey>-¢ GAN) ye pure dt SHEN Toss moos maar nose (aH) ‘epee a) _=2uepaduyanduy ‘asuodsoy Aouenba1y I+QHL%S'0 ‘m9 | Go omod paiey415.0mm - 401.5mm 390.0mm 26mm4, FRONT PANEL Take the 4-channel model as sample: ' Com 4, Power switch ower 6. Channel-B volume knob 2, Overdrive / Error indicator (same foreach channel) 7, Channel-C volume knob 3, Signal output indicator (same foreach channel) 8 Channel-D volume knob 4, Power indicator ( same for each channel ) 9, Ventilation hole 5, Channel-A volume knob "5. INDICATORS ON FRONT PANEL PWR power indicator, power on SIGNAL signal output indicator for each seperated channel SIGNAL signal indicator is equivalent to outputs paralleled on the circuit. When the Gain is turned to minimum and whether there is input signal, the signal indicator will not light up. CLIP / ERR output overdrive / error indicator for each seperated channel When input signal is too big, the CLIP / ERR indicator lights up. Too strong and continuous clip may cause damage to the speaker and sound. Please reduce gain or signal input when the clip is too frequentCLIP/ ERR for more indications: (next page) 1.CLIP/ ERR lights up when the amplifier is powered on during self-examine process, The process has not any output and after 2s examination, CLIP / ERR lights off. 2.CLIP / ERR lights up when the amplifier is short circuit or at too low impedance, however it can be off by turn off volume. Please check the loading impedance and output connection. 3.CLIP/ ERR lights up when device temperature is over the limit and output is temporarily cut off. Please turn off the amplifier, improve the cooling condition, and clean the ventilation. 4.CLIP / ERR lights up when defection appears, if you are not sure the problems, please consult techni 6. REAR PANEL ~ 2-Channel model. 1.Channel-A signal input (XLR) 7.Channel-B power output (binding post ) 3 2.Channel-B signal input (XLR) 8.Channel-A power output (NL4) ol 3.Link-A signal output (XLR) 9.Channel-B power output (NL4) 4.Link-B signal output (XLR) 10.Power cord \ 5. Switch for link or normal mode 11.Fuse 6.Channel-A power output (binding post) —_12.Ventilation hole3-channel model 0 " 15 10 1.Channel-A signal input (XLR) 2.Channel-B signal input (XLR) 3.Channel-C signal input (XLR) 4.Link-B signal output (XLR) 5.Link-A signal output (TRS) 6.Channel-A power output (binding post ) 7.Channel-B power output (binding post ) 8.Channel-C power output (binding post ) 4-channel 1.Channel-A signal input (XLR) 2.Channel-B signal input (XLR) 3.Channel-C signal input (XLR) 4.Channel-C signal input (XLR) 5.Link-A signal output (TRS) 6.Channel-A power output (binding post ) 7.Channel-B power output (binding post ) 8.Channel-C power output (binding post ) 9.Channel-D power output (binding post ) Sz pusde USaY come Mste reo" oX2, & liek Be ‘ PET Rwy s lero? 4 es P W os, 3012 4 13, 9.Channel-A power output (NL4) 10.Channel-B power output (NL4) 11.Channel-C power output (NL4) 12.Switch for link or normal mode. 13..Power cord 14.Fuse 15.Ventilation hole. U.Channel-A power output (NL4) 11.Channel-B power output (NL4) 12.Channel-C power output (NL4) 13.Channel-D power output (NL4) 14. Switch for link or normal mode. 15.Power cord 16.Fuse ae 17.Nentilation hole.7. POWER SUPPLY a Make sure the local voltage complies with the voltage requirement indicated at the back of amplifier b.Make sure the power cord and socket are good, the plug type matches the socket. ¢.Make sure the amplifier is well connected to earth. Pull out plug after power off. e.Select the power volume based on power consumption indicated in the data sheet. 8. INPUT / OUTPUT CONNECTORS i Input connectors ‘The product is designed with balanced input circuit to lower noise, please use balanced connection for the device. ‘A Note: If your signal output device is an unbalanced circuit design, please do not use single core shielded wire, connect the negative pole of dual core wire to earth and make balanced input connection to get equivalent noise restrain There is a XLR socket for each channel. In LINK mode, the input sockets are in parallel, you can input signal to any channel socket. In different models, there are XLR and TRS socket for link output, which is paralleled with the input socket. You can connect the other amplifier from the output socket and even link in groups. This link method is very convenient, but link too much will cause signal interference or lost. ‘A Note: In LINK mode, do not input signal to both channel sockets at the same time, which will cause abnormal operations. ie APT out gut Ge a + Wl Output connectors inp € SS out put There are one group binding post and one NL4 MP socket as power output connector for each channel, which are in parallel connection. For each channel, the red binding post connects positive pole of power output while the black binding post connects negative pole. The 1+ leg of NL4 socket connects positive pole of power output while 1- leg connects negative pole. A Note: For each channel, do noy drys the speaker whose impedance is less than 4ohm, which may cause abnormal or overheat use ‘A Note: The output voltage may cause electric shock. Make sure the amplifier is off when you connect the speaker. Do not touch the naked part between amplifier output and the speaker wire.| one 9. FUNCTION SETUP AND CABLE CONNECTION Ml Gain control altt pur Tum the gain knob clockwise on the front panel to increase gain, turn anticlockwise to decrease gain Note! The gain knob is not for amplifier power rather than amplification times for input signal Note! When the gain is turned too small (less than 12 o'clock position), the signal may be damaged in Pre-process, in which case, the amplifier cannot deliver full power by increase signal input. mal wn I Mode select and signal cable connection, = Connection diagram = eS sy a Diagram for plug connection SS 3 a Sine tgp ® = = ss roe ae — ©} profess or to connect cable. There is high voltage from output terminal when the device is working, be ware electric shock and make sure power off before connecting cable. A. Allthe input / output sockets and binding posts are located on back panel, please consult = Manufacturer shall not be responsible for any kind of device damages or human injures =< caused by incorrect operation aoe +e A, NORMAL MODE SE eS The factory setting is at NORMAL mode cine re =e as the right picture indicated gE xe oma sora Signal for two channels that ie closed to power switch play individually and ie ave amplified individually as well. 4S ae + LINK MODE g Turn to LINK mode as the right picture uNK___NoRMAL 3 indicated: the signal can be input to any - channel that is closed to power switch, a the same signal can be output from any NORMAL channellinked, Note: do not input signal to the linked aaa neither parallel the output terminals.) ™ eae10.OPERATIONS Please take the following steps: 1> Power on. a.make the correct setting and connection b.check if there is short output connection, check if there is incorrect low impedance: c.check local electricity to conform to the voltage of our product. d.make sure the switch is off, and the volume is minimum. e.connect to the main, turn on signal device and other processors. f. turn on the switch. g.turn the volume clockwise to a suitable level. 2> Power off a- turn the volume to minimum b- turn off the switch c- turn off signal device and other processors 44. PROTECTION AND COLLING SYSTE Efficient and secure circuit design for low defect rate and high protection to avoid damage to the sound system due to improper operation and application. Over-current and overdrive protection. Full protection to the power output IC regarding output overdrive, short circuit, wrong loading and incorrect wiring, Output DC protection and limit to HF to avoid damage to the system. Temperature protection in tough condition.12. TROUBLES AND TROUBLE SHOOTINGS Trouble shootings | Trouble Ne Sounding power 2 | Check if there is AC100-120V, 50/60Hz on the socket. indication = 3 | Check ifthe circuit breaker on real panel is shut off, push it back. 1 | Check ifthe signal cable is connected well. No sound, power indicator | 5 | Check ifthe signal device is on and its volume. is on, SIG indi is | Check if the amplifier volume is on. |” Check ithe signal inputs too high CLIP / ERR indicator flashes, - abnormal sound. 2. | Check if output connection is short, check the loading impedance and then restart the device. 4 | Checkand make sure the switch at rear panel is at LINK position In LINK mode, one EE a channel no sound, 2 | Check if channel volume is on.413. SAFETY ATTENTIONS SAFEFY REGULATIONS ABNORMAL PHENOMENA: Please tum off the power and pull out the plug when You find unusual sound or smell when operation _POWER CORDS PROTECTION Don't touch power cords with wet hands to avoid ‘electric shock. Don't put the cords in crowded people. AEEPAL (TER AND SUMDRV GOODS ONT OPEN THE COVERIENOT CUIDED ACAD ELECTAICAY LiL, OLE THEPOMER CORDS [OAYOM LREWHEN VOU DONT USE THIS LMToun pet Assigned pin 12 Signal GND Lr sv es Siynal CF) ae piv 3! Signal —) Pins oO utput Asian meat & Speakon) | INA A: CHA Sinat] ca PINAD): CH ND ; MULTI-CHANNEL POWER AMPLIFIER Mod: Norm 4.6 AC i ifs ~1ZoV. 60lHre,4,500VA Circuit Breaker: 30A /250V BO Per channel 600 W 4Q Pey channel 4,000 W yan 4G Audio + fach welegy 2Don gga tae a WV | Maa 14 CO. i * quan Dons —> loan | chine ov