UDC 621.882.215.1.091.4 ‘September 1986 Slotted pan head screws with large head Flachkopfschrauben mit Schlitz und groBem Kopt Supersedes August 1972 edition In keeping with current practice in standards published by the International Organization for Standardization (ISO),a comma hhas been used throughout as the decimal marker, Dimensions in mm 1 Dimensions Radiusing instead of Hae ‘chamfering permitted, at ie the manufacturer's discretion. —-} ve up toms SRB tees 1 Gincomplete thread: Srceesing M3 1.5 P maximum. a2 as specified in DIN 76 Part 1 (2P maximum) DIN 78-K or DIN 78-L thread ends, at the manufacturer's discretion. Thread size d m2 04 Nominal size| 16 2A 26 at 37 42 48 52 58 62 1) P= pitch of thread (coarse pitch thread) Continued on pages 2 to 4 164Page 2. DIN 921 Table (concluded) Thread size d M3 (M35) M4 MS M6 me M10 P os | ae oe | 1s | ta eae ee Go estas ees Pia etttacansiaadla Weiser! Wee . ~ res | gee | sr | 1557 | toaa | zaaa | c0ae f = 045 os 06 o7 0B 03 at 7 leemiees 18 2 24 27 ai ae | 48 es vse | are | 252 | ase | oa | ass | «7s nin. 1,68 | 228 295 365 | 445, Nominal size 08 | ee 1,2 . | ane | oa | roe | 120 | vos | ace | 2x0 om i 12 1st) 191 231 281 rae or | or | o2 | o2 | ov | a« | o# | : ae oo | 1 12 13 | 18 19 23 es us [sa | we | ow | to | ae | ae 1 ee 7 [oe [os TI 5 4a | 52 | «| 58 |e | 8 78 | a2 . i 10 : 98 10,2 | | 12 VW 123 | | | (14) 137 143 oe we | wy | 16s | (18) 7 i “183 | 2 | 197 | 203 [ag aioes atnen pin bo cand elon ste Tivoad sizes and intrmeate lengths given in brackets should be avoided i possible Slotted pan head screws are normally manufactured inthe range indicat by stepped lines 9 pitch of thread (coarse pitch thread). 165DIN 921 Page 3 2. Technical delivery conditions Material Steel Stainless steel Non-terrous metal General requirements AAs specified in DIN 267 Part 1 Tolerance class For sizes up to and including M1,4: 4hy; from size M1,6: 6g, Thread 4 Standard DIN 13 Part 15 Property class A150 58) is Reese (material) c4-50 properties?) ISO 898 Part 1 Standard (caipecsonein DIN 267 Part 11 DIN 267 Part 18 Permissible dimensional Product grade For sizes up to and including M1.4: F; from size M16: A (oviations and wp - (eviatons of fom Standard DIN 267 Part 6; ISO 4759 Part 1 Types and finishes with aitional information Named ‘As specified in DIN 962 ‘As processed. Bright Bright ‘Surface finish DIN 267 Part 2 shall apply with regard to surface roughness. DIN 267 Part 19 shall apply'with regard to permissible surface discontinuities. DIN 267 Part 9 shall apply with regard to electroplating ‘Acceptance inspection DIN 267 Part 5 shall apply with regard to acceptance inspection, ) Where cold drawn steels as specified in DIN 1651 are used, the following values of elongation at break, As, are permissible for sizes not exceeding M4, 5%; for sizes larger than M4 up to and including sizes not exceeding M8, 6%; for size M10,7%, 2) Cuzn = CU2 oF CUS (as specified in DIN 267 Part 18), at the manufacturer's discretion. 2) Other property classes or materials shall be subject to agreement, 3. Designation Designation of an MS slotted pan head screw with large head, of nominal length [= 10mm, assigned to property class 5.8") Pan head screw DIN 921~M5 x 10-58 ‘The DIN 4000- 2-1 tabular layout of article characteristics shall apply to screws conforming to this standard. 1) Where no property class or type of material is given in existing documentation, property class 5.8 shall apply. 166Page 4 DIN92t Standards referred to DIN 13 Part 18 DIN. 76 Part1 DIN 78 DIN 267 Part 1 DIN 267 Part 2 DIN 267 Part 5 DIN 267 Part 6 DIN 267 Part 9 DIN. 267 Part 11 DIN 267 Part 18 DIN 267 Part 19 DIN. 962 DIN 1651 DIN 4000 Part 2 ISO 898 Part 1 180 4759 Part 1 1SO metric screw threads; fUndamental deviations and tolerances for screw threads of 1mm and larger Thread run-outs and thread undercuts for ISO metric threads as specified in DIN 13 Thread ends; lengths of projection of thread ends for ISO metric screw threads as defined in DIN 13 Fasteners; technical delivery conditions; general requirements Fasteners; technical delivery conditions; types of finish and dimensional accuracy Fasteners; technical delivery conditions; acceptance inspection (modified version of ISO 3269, 1984 edition) Fasteners; technical delivery conditions; types of finish and dimensional accuracy for product grade F Fasteners; technical delivery conditions; components with electroplated coatings Fasteners; technical delivery conditions (with additions to SO 3506); corrosion-resistant stainless steel fasteners Fasteners; technical delivery conditions; components made of non-ferrous metals Fasteners; technical delivery conditions; surface discontinuities on bolts and screws Screws, bolts, studs and nuts; designations, types and finishes Froe cutting steels; technical delivery conditions Tabular layouts of article characteristics for bolts, studs and nuts Mechanical properties of fasteners; bolts, screws and studs Tolerances for fasteners; bolts, screws and nuts with thread diameters between 1,6 (inclusive) and 150mm (inclusive) and product grades A, B and C Previous editions 01.43, 0254, 0872 Amendments ‘The following amendments have been made in comparison with the August 1972 edition. a) Size M18 has been deleted because there is no demand for it. »b) The previous design m as specified in DIN 267 Part 2, April 1968 edition, has been replaced by product grade Fas specified in DIN 267 Part 6 and product grade A as specified in ISO 4759 Part 1. ©) Limiting dimensions calculated from the permissible tolerances have been included. ) Length /= 1mm has been deleted since it has proved impracticable. @) The technical delivery conditions have been amended. f) The content of the standard has been editor ly revised, 9) The example of designation has been amended. International Patent Classification F168 23/00 F168 35/00 167