Lenovo Y470/Y570

Hardware
Maintenance
Manual
 Note:
Before using this information and the product it supports, be sure to read the general information
under “Notices” on page 98.

First Edition (March 2011)

© Copyright Lenovo 2011. All rights reserved.
LENOVO products, data, computer software, and services have been developed exclusively at private
expense and are sold to governmental entities as commercial items as defined by 48 C.F.R. 2.101 with
limited and restricted rights to use, reproduction and disclosure.
LIMITED AND RESTRICTED RIGHTS NOTICE: If products, data, computer software, or services are
delivered pursuant a General Services Administration “GSA” contract, use, reproduction, or disclo-
sure is subject to restrictions set forth in Contract No. GS-35F-05925.
© 2011 Lenovo
 Contents
About this manual........................................iv 1030 Hard disk drive(HDD)/Memory/
Mini PCI Express Card slot compartment
Safety information.........................................1 cover .............................................................. 36
General safety ...................................................... 2 1040 Hard disk drive ................................... 37
Electrical safety .................................................... 3 1050 Optical drive........................................ 39
Safety inspection guide ...................................... 5 1060 DIMM ................................................... 40
Handling devices that are sensitive to 1070 PCI Express Mini Card for wireless
electrostatic discharge......................................... 6 LAN/WAN and TV Card .......................... 41
Grounding requirements ................................... 6 1080 Keyboard.............................................. 44
Safety notices: multilingual translations.......... 7 1090 Keyboard bezel ................................... 49
Laser compliance statement............................. 14 1100 System board ....................................... 53
Important service information ...................16 1110 LCD unit............................................... 57
Strategy for replacing FRUs............................. 16 1120 Fan assembly and Heat Sink
Strategy for replacing a hard disk assembly........................................................ 60
drive .............................................................. 17 1130 CPU....................................................... 62
Important notice for replacing a system 1140 Base cover, speakers and bluetooth
board ............................................................. 17 card ................................................................ 63
Important information about replacing RoHS 1150 LCD front bezel................................... 67
compliant FRUs ................................................. 18 1160 LCD panel, LCD cable and
hinges............................................................. 69
General checkout ........................................19 1170 Integrated camera ............................... 72
What to do first .................................................. 20 1180 Antenna assembly and LCD
Power system checkout .................................... 21 cover .............................................................. 73
Checking the AC adapter........................... 21 Locations ............................................................. 74
Checking operational charging ................. 21 Front view ..................................................... 74
Checking the battery pack ......................... 22 Right-side view ............................................ 75
Bottom and Left-side view ......................... 76
Related service information .......................23
Parts list ............................................................... 77
Restoring the factory contents by using OneKey
Overall ........................................................... 78
Recovery ............................................................. 23
LCD FRUs ..................................................... 85
Restore of factory default ........................... 23
Keyboard....................................................... 88
Using recovery discs ................................... 23
Keyboard....................................................... 91
Passwords........................................................... 24
Miscellaneous parts ..................................... 93
Power-on password .................................... 24
AC adapters.................................................. 94
Supervisor password .................................. 24
Power cords .................................................. 95
Power management .......................................... 25
Screen blank mode ...................................... 25 Notices ......................................................... 98
Sleep (standby) mode ................................. 25 Trademarks......................................................... 99
Hibernation mode ....................................... 26

Lenovo Y470/Y570 ......................................27

Specifications ..................................................... 27
Status indicators ................................................ 29
Fn key combinations ......................................... 31
FRU replacement notices.................................. 32
Screw notices................................................ 32
Removing and replacing an FRU.................... 33
1010 Battery pack......................................... 34
1020 Dummy card ....................................... 35

iii
 About this manual
This manual contains service and reference information for the following
Lenovo product:
IdeaPad Y470/Y570
Use this manual to troubleshoot problems.
The manual is divided into the following sections:
• The common sections provide general information, guidelines, and safety
information required for servicing computers.
• The product-specific section includes service, reference, and product-specific
parts information.

Important:
This manual is intended only for trained servicers who are familiar with
Lenovo products. Use this manual to troubleshoot problems effectively.
Before servicing a Lenovo product, make sure to read all the information
under “Safety information” on page 1 and “Important service information”
on page 16.

iv
 Safety information

Safety information
This chapter presents the following safety information that you need to get
familiar with before you service a Lenovo computer:
• “General safety” on page 2
• “Electrical safety” on page 3
• “Safety inspection guide” on page 5
• “Handling devices that are sensitive to electrostatic discharge” on page 6
• “Grounding requirements” on page 6
• “Safety notices: multilingual translations” on page 7
• “Laser compliance statement” on page 14

1
 Lenovo Y470/Y570 Hardware Maintenance Manual

General safety

Follow these rules below to ensure general safety:

• Observe a good housekeeping in the area where the machines are put during
and after the maintenance.
• When lifting any heavy object:
1. Make sure that you can stand safely without slipping.
2. Distribute the weight of the object equally between your feet.
3. Use a slow lifting force. Never move suddenly or twist when you attempt
to lift it.
4. Lift it by standing or pushing up with your leg muscles; this action could
avoid the strain from the muscles in your back. Do not attempt to lift any
object that weighs more than 16 kg (35 lb) or that you think is too heavy for
you.
• Do not perform any action that causes hazards to the customer, or that makes
the machine unsafe.
• Before you start the machine, make sure that other service representatives
and the customer are not in a hazardous position.
• Please remove covers and other parts in a safe place, away from all
personnel, while you are servicing the machine.
• Keep your toolcase away from walk areas so that other people will not trip it
over.
• Do not wear loose clothing that can be trapped in the moving parts of the
machine. Make sure that your sleeves are fastened or rolled up above your
elbows. If your hair is long, fasten it.
• Insert the ends of your necktie or scarf inside clothing or fasten it with the
nonconductive clip, about 8 centimeters (3 inches) from the end.
• Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for
your clothing.
Attention: Metal objects are good electrical conductors.
• Wear safety glasses when you are hammering, drilling, soldering, cutting
wire, attaching springs, using solvents, or working in any other conditions
that may be hazardous to your eyes.
• After service, reinstall all safety shields, guards, labels, and ground wires.
Replace any safety device that is worn or defective.
• Reinstall all covers correctly before returning the machine to the customer.
• Fan louvers on the machine help to prevent the overheating of internal
components. Do not obstruct fan louvers or cover them with labels or
stickers.

2
 Safety information

Electrical safety

Observe the following rules when working on electrical equipments.

Important:
Use only approved tools and test equipments. Some hand tools have
handles covered with a soft material that does not insulate you when
working with live electrical currents.
Many customers have rubber floor mats near their machines that contain
small conductive fibers to decrease electrostatic discharges. Do not use such
kind of mat to protect yourself from electrical shock.

• Find the room emergency power-off (EPO) switch, disconnecting switch, or

electrical outlet. If an electrical accident occurs, you can then operate the
switch or unplug the power cord quickly.
• Do not work alone under hazardous conditions or near the equipment that
has hazardous voltages.
• Disconnect all power before:
– Performing a mechanical inspection
– Working near power supplies
– Removing or installing main units
• Before you start to work on the machine, unplug the power cord. If you
cannot unplug it, ask the customer to power-off the wall box that supplies
power to the machine, and to lock the wall box in the off position.
• If you need to work on a machine that has exposed electrical circuits, observe
the following precautions:
– Ensure that another person, familiar with the power-off controls, is near
you.
Attention: Another person must be there to switch off the power, if
necessary.
– Use only one hand when working with powered-on electrical equipment;
keep the other hand in your pocket or behind your back.
Attention: An electrical shock can occur only when there is a complete
circuit. By observing the above rule, you may prevent a current from
passing through your body.
– When using testers, set the controls correctly and use the approved probe
leads and accessories for that tester.
– Stand on suitable rubber mats (obtained locally, if necessary) to insulate
you from grounds such as metal floor strips and machine frames.
Observe the special safety precautions when you work with very high voltages;
instructions for these precautions are in the safety sections of maintenance
information. Be extremely careful when you measure the high voltages.
• Regularly inspect and maintain your electrical hand tools for safe operational
condition.
• Do not use worn or broken tools and testers.
• Never assume that power has been disconnected from a circuit. First, check it
to make sure that it has been powered off.

3
 Lenovo Y470/Y570 Hardware Maintenance Manual

• Always look carefully for possible hazards in your work area. Examples of
these hazards are moist floors, nongrounded power extension cables, power
surges, and missing safety grounds.
• Do not touch live electrical circuits with the reflective surface of a plastic
dental mirror. The surface is conductive; such touching can cause personal
injury and machine damage.
• Do not service the following parts with the power on when they are removed
from their normal operating places in a machine:
– Power supply units
– Pumps
– Blowers and fans
– Motor generators
and similar units. (This practice ensures correct grounding of the units.)
• If an electrical accident occurs:
– Use caution: do not become a victim yourself.
– Switch off the power.
– Send the victim to get medical aid.

4
 Safety information

Safety inspection guide

The purpose of this inspection guide is to assist you in identifying potential

unsafe conditions. As each machine was designed and built, required safety
items were installed to protect users and service personnel from injury. This
guide addresses only those items. You should use good judgment to identify
potential safety hazards due to attachment of non-Lenovo features or options not
covered by this inspection guide.

If any unsafe conditions are present, you must determine how serious the
apparent hazard could be and whether you can continue without first correcting
the problem.

Consider these conditions and the safety hazards they present:

• Electrical hazards, especially primary power (primary voltage on the frame
can cause serious or fatal electrical shock)
• Explosive hazards, such as a damaged CRT face or a bulging capacitor
• Mechanical hazards, such as loose or missing hardware

To determine whether there are any potential unsafe conditions, use the
following checklist at the beginning of every service task. Begin the checks with
the power off, and the power cord disconnected.

Checklist:
1. Check exterior covers for damage (loose, broken, or sharp edges).
2. Turn off the computer. Disconnect the power cord.
3. Check the power cord for:
a. A third-wire ground connector in good condition. Use a meter to measure
third-wire ground continuity for 0.1 ohm or less between the external
ground pin and the frame ground.
b. The power cord should be the type specified in the parts list.
c. Insulation must not be frayed or worn.
4. Check for cracked or bulging batteries.
5. Remove the cover.
6. Check for any obvious non-Lenovo alterations. Use good judgment as to the
safety of any non-Lenovo alterations.
7. Check inside the unit for any obvious unsafe conditions, such as metal filings,
contamination, water or other liquids, or signs of fire or smoke damage.
8. Check for worn, frayed, or pinched cables.
9. Check that the power-supply cover fasteners (screws or rivets) have not been
removed or tampered with.

5
 Lenovo Y470/Y570 Hardware Maintenance Manual

Handling devices that are sensitive to electrostatic discharge

Any computer part containing transistors or integrated circuits (ICs) should be

considered sensitive to electrostatic discharge (ESD). ESD damage can occur
when there is a difference in charge between objects. Protect against ESD damage
by equalizing the charge so that the machine, the part, the work mat, and the
person handling the part are all at the same charge.

Notes:
1. Use product-specific ESD procedures when they exceed the
requirements noted here.
2. Make sure that the ESD protective devices you use have been certified
(ISO 9000) as fully effective.

When handling ESD-sensitive parts:

• Keep the parts in protective packages until they are inserted into the product.
• Avoid contact with other people.
• Wear a grounded wrist strap against your skin to eliminate static on your
body.
• Prevent the part from touching your clothing. Most clothing is insulative and
retains a charge even when you are wearing a wrist strap.
• Use the black side of a grounded work mat to provide a static-free work
surface. The mat is especially useful when handling ESD-sensitive devices.
• Select a grounding system, such as those listed below, to provide protection
that meets the specific service requirement.

Notes:
The use of a grounding system to guard against ESD damage is desirable but
not necessary.

– Attach the ESD ground clip to any frame ground, ground braid, or green-
wire ground.
– When working on a double-insulated or battery-operated system, use an
ESD common ground or reference point. You can use coax or connector-
outside shells on these systems.
– Use the round ground prong of the ac plug on ac-operated computers.

Grounding requirements

Electrical grounding of the computer is required for operator safety and correct
system function. Proper grounding of the electrical outlet can be verified by a
certified electrician.

6
 Safety information

Safety notices: multilingual translations

The safety notices in this section are provided in English, French, German,
Hebrew, Italian, Japanese, and Spanish.

Safety notice 1
Before the computer is powered on after FRU replacement, make sure all
screws, springs, and other small parts are in place and are not left loose
inside the computer. Verify this by shaking the computer and listening for
rattling sounds. Metallic parts or metal flakes can cause electrical shorts.
Avant de remettre l’ordinateur sous tension après remplacement d’une unité
en clientèle, vérifiez que tous les ressorts, vis et autres pièces sont bien en
place et bien fixées. Pour ce faire, secouez l’unité et assurez-vous qu’aucun
bruit suspect ne se produit. Des pièces métalliques ou des copeaux de métal
pourraient causer un court-circuit.
Bevor nach einem FRU-Austausch der Computer wieder angeschlossen
wird, muß sichergestellt werden, daß keine Schrauben, Federn oder andere
Kleinteile fehlen oder im Gehäuse vergessen wurden. Der Computer muß
geschüttelt und auf Klappergeräusche geprüft werden. Metallteile oder-
splitter können Kurzschlüsse erzeugen.

Prima di accendere l’elaboratore dopo che é stata effettuata la sostituzione di

una FRU, accertarsi che tutte le viti, le molle e tutte le altri parti di piccole
dimensioni siano nella corretta posizione e non siano sparse all’interno
dell’elaboratore. Verificare ciò scuotendo l’elaboratore e prestando
attenzione ad eventuali rumori; eventuali parti o pezzetti metallici possono
provocare cortocircuiti pericolosi.

Antes de encender el sistema despues de sustituir una FRU, compruebe que

todos los tornillos, muelles y demás piezas pequeñas se encuentran en su
sitio y no se encuentran sueltas dentro del sistema. Compruébelo agitando el
sistema y escuchando los posibles ruidos que provocarían. Las piezas
metálicas pueden causar cortocircuitos eléctricos.

7
 Lenovo Y470/Y570 Hardware Maintenance Manual

Safety notice 2
DANGER
Some standby batteries contain a small amount of nickel and cadmium. Do
not disassemble a standby battery, recharge it, throw it into fire or water, or
short-circuit it. Dispose of the battery as required by local ordinances or
regulations. Use only the battery in the appropriate parts listing. Use of an
incorrect battery can result in ignition or explosion of the battery.
Certaines batteries de secours contiennent du nickel et du cadmium. Ne les
démontez pas, ne les rechargez pas, ne les exposez ni au feu ni à l’eau. Ne
les mettez pas en court-circuit. Pour les mettre au rebut, conformez-vous à
la réglementation en vigueur. Lorsque vous remplacez la pile de sauvegarde
ou celle de l’horloge temps réel, veillez à n’utiliser que les modèles cités dans
la liste de pièces détachées adéquate. Une batterie ou une pile inappropriée
risque de prendre feu ou d’exploser.
Die Bereitschaftsbatterie, die sich unter dem Diskettenlaufwerk befindet,
kann geringe Mengen Nickel und Cadmium enthalten. Sie darf nicht
zerlegt, wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser
ausgesetzt werden. Bei der Entsorgung die örtlichen Bestimmungen für
Sondermüll beachten. Beim Ersetzen der Bereitschafts-oder Systembatterie
nur Batterien des Typs verwenden, der in der Ersatzteilliste aufgeführt ist.
Der Einsatz falscher Batterien kann zu Entzündung oder Explosion führen.

Alcune batterie di riserva contengono una piccola quantità di nichel e

cadmio. Non smontarle, ricaricarle, gettarle nel fuoco o nell’acqua né
cortocircuitarle. Smaltirle secondo la normativa in vigore (DPR 915/82,
successive disposizioni e disposizioni locali). Quando si sostituisce la
batteria dell’RTC (real time clock) o la batteria di supporto, utilizzare
soltanto i tipi inseriti nell’appropriato Catalogo parti. L’impiego di una
batteria non adatta potrebbe determinare l’incendio o l’esplosione della
batteria stessa.

Algunas baterías de reserva contienen una pequeña cantidad de níquel y

cadmio. No las desmonte, ni recargue, ni las eche al fuego o al agua ni las
cortocircuite. Deséchelas tal como dispone la normativa local. Utilice sólo
baterías que se encuentren en la lista de piezas. La utilización de una batería
no apropiada puede provocar la ignición o explosión de la misma.

8
 Safety information

Safety notice 3
DANGER
The battery pack contains small amounts of nickel. Do not disassemble it,
throw it into fire or water, or short-circuit it. Dispose of the battery pack as
required by local ordinances or regulations. Use only the battery in the
appropriate parts listing when replacing the battery pack. Use of an
incorrect battery can result in ignition or explosion of the battery.
La batterie contient du nickel. Ne la démontez pas, ne l’exposez ni au feu ni
à l’eau. Ne la mettez pas en court-circuit. Pour la mettre au rebut,
conformez-vous à la réglementation en vigueur. Lorsque vous remplacez la
batterie, veillez à n’utiliser que les modèles cités dans la liste de pièces
détachées adéquate. En effet, une batterie inappropriée risque de prendre
feu ou d’exploser.
Akkus enthalten geringe Mengen von Nickel. Sie dürfen nicht zerlegt,
wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetzt
werden. Bei der Entsorgung die örtlichen Bestimmungen für Sondermüll
beachten. Beim Ersetzen der Batterie nur Batterien des Typs verwenden, der
in der Ersatzteilliste aufgeführt ist. Der Einsatz falscher Batterien kann zu
Entzündung oder Explosion führen.

La batteria contiene piccole quantità di nichel. Non smontarla, gettarla nel

fuoco o nell’acqua né cortocircuitarla. Smaltirla secondo la normativa in
vigore (DPR 915/82, successive disposizioni e disposizioni locali). Quando
si sostituisce la batteria, utilizzare soltanto i tipi inseriti nell’appropriato
Catalogo parti. L’impiego di una batteria non adatta potrebbe determinare
l’incendio o l’esplosione della batteria stessa.

Las baterías contienen pequeñas cantidades de níquel. No las desmonte, ni

recargue, ni las eche al fuego o al agua ni las cortocircuite. Deséchelas tal
como dispone la normativa local. Utilice sólo baterías que se encuentren en
la lista de piezas al sustituir la batería. La utilización de una batería no
apropiada puede provocar la ignición o explosión de la misma.

9
 Lenovo Y470/Y570 Hardware Maintenance Manual

Safety notice 4
DANGER
The lithium battery can cause a fire, an explosion, or a severe burn. Do not
recharge it, remove its polarized connector, disassemble it, heat it above
100°C (212°F), incinerate it, or expose its cell contents to water. Dispose of
the battery as required by local ordinances or regulations. Use only the
battery in the appropriate parts listing. Use of an incorrect battery can result
in ignition or explosion of the battery.
La pile de sauvegarde contient du lithium. Elle présente des risques
d’incendie, d’explosion ou de brûlures graves. Ne la rechargez pas, ne
retirez pas son connecteur polarisé et ne la démontez pas. Ne l’exposez pas
à une temperature supérieure à 100°C, ne la faites pas brûler et n’en exposez
pas le contenu à l’eau. Mettez la pile au rebut conformément à la
réglementation en vigueur. Une pile inappropriée risque de prendre feu ou
d’exploser.
Die Systembatterie ist eine Lithiumbatterie. Sie kann sich entzünden,
explodieren oder schwere Verbrennungen hervorrufen. Batterien dieses
Typs dürfen nicht aufgeladen, zerlegt, über 100 C erhitzt oder verbrannt
werden. Auch darf ihr Inhalt nicht mit Wasser in Verbindung gebracht oder
der zur richtigen Polung angebrachte Verbindungsstecker entfernt werden.
Bei der Entsorgung die örtlichen Bestimmungen für Sondermüll beachten.
Beim Ersetzen der Batterie nur Batterien des Typs verwenden, der in der
Ersatzteilliste aufgeführt ist. Der Einsatz falscher Batterien kann zu
Entzündung oder Explosion führen.

La batteria di supporto e una batteria al litio e puo incendiarsi, esplodere o

procurare gravi ustioni. Evitare di ricaricarla, smontarne il connettore
polarizzato, smontarla, riscaldarla ad una temperatura superiore ai 100
gradi centigradi, incendiarla o gettarla in acqua. Smaltirla secondo la
normativa in vigore (DPR 915/82, successive disposizioni e disposizioni
locali). L’impiego di una batteria non adatta potrebbe determinare
l’incendio o l’esplosione della batteria stessa.

La batería de repuesto es una batería de litio y puede provocar incendios,

explosiones o quemaduras graves. No la recargue, ni quite el conector
polarizado, ni la desmonte, ni caliente por encima de los 100°C (212°F), ni la
incinere ni exponga el contenido de sus celdas al agua. Deséchela tal como
dispone la normativa local.

10
 Safety information

Safety notice 5
If the LCD breaks and the fluid from inside the LCD gets into your eyes or
on your hands, immediately wash the affected areas with water at least for
15 minutes. Seek medical care if any symptoms caused by the fluid are
present after washing.
Si le panneau d’affichage à cristaux liquides se brise et que vous recevez dans
les yeux ou sur les mains une partie du fluide, rincez-les abondamment
pendant au moins quinze minutes. Consultez un médecin si des symptômes
persistent après le lavage.
Die Leuchtstoffröhre im LCD-Bildschirm enthält Quecksilber. Bei der
Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Der
LCD-Bildschirm besteht aus Glas und kann zerbrechen, wenn er
unsachgemäß behandelt wird oder der Computer auf den Boden fällt. Wenn
der Bildschirm beschädigt ist und die darin befindliche Flüssigkeit in
Kontakt mit Haut und Augen gerät, sollten die betroffenen Stellen
mindestens 15 Minuten mit Wasser abgespült und bei Beschwerden
anschließend ein Arzt aufgesucht werden.

Nel caso che caso l’LCD si dovesse rompere ed il liquido in esso contenuto
entrasse in contatto con gli occhi o le mani, lavare immediatamente le parti
interessate con acqua corrente per almeno 15 minuti; poi consultare un
medico se i sintomi dovessero permanere.

Si la LCD se rompe y el fluido de su interior entra en contacto con sus ojos o

sus manos, lave inmediatamente las áreas afectadas con agua durante
15 minutos como mínimo. Obtenga atención medica si se presenta algún

11
 Lenovo Y470/Y570 Hardware Maintenance Manual

Safety notice 6
DANGER
To avoid shock, do not remove the plastic cover that protects the lower part
of the inverter card.
Afin d’éviter tout risque de choc électrique, ne retirez pas le cache en
plastique protégeant la partie inférieure de la carte d’alimentation.
Aus Sicherheitsgründen die Kunststoffabdeckung, die den unteren Teil der
Spannungswandlerplatine umgibt, nicht entfernen.

Per evitare scosse elettriche, non rimuovere la copertura in plastica che

avvolge la parte inferiore della scheda invertitore.

Para evitar descargas, no quite la cubierta de plástico que rodea la parte baja
de la tarjeta invertida.

Safety notice 7
DANGER
Though the main batteries have low voltage, a shorted or grounded battery
can produce enough current to burn personnel or combustible materials.
Bien que le voltage des batteries principales soit peu élevé, le court-circuit ou
la mise à la masse d’une batterie peut produire suffisamment de courant
pour brûler des matériaux combustibles ou causer des brûlures corporelles
graves.
Obwohl Hauptbatterien eine niedrige Spannung haben, können sie doch bei
Kurzschluß oder Erdung genug Strom abgeben, um brennbare Materialien
zu entzünden oder Verletzungen bei Personen hervorzurufen.

Sebbene le batterie di alimentazione siano a basso voltaggio, una batteria in

corto circuito o a massa può fornire corrente sufficiente da bruciare materiali
combustibili o provocare ustioni ai tecnici di manutenzione.

Aunque las baterías principales tienen un voltaje bajo, una batería

cortocircuitada o con contacto a tierra puede producir la corriente suficiente
como para quemar material combustible o provocar quemaduras en el
personal.

12
 Safety information

Safety notice 8
DANGER
Before removing any FRU, turn off the computer, unplug all power cords
from electrical outlets, remove the battery pack, and then disconnect any
interconnecting cables.
Avant de retirer une unité remplaçable en clientèle, mettez le système hors
tension, débranchez tous les cordons d’alimentation des socles de prise de
courant, retirez la batterie et déconnectez tous les cordons d’interface.
Die Stromzufuhr muß abgeschaltet, alle Stromkabel aus der Steckdose
gezogen, der Akku entfernt und alle Verbindungskabel abgenommen sein,
bevor eine FRU entfernt wird.

Prima di rimuovere qualsiasi FRU, spegnere il sistema, scollegare dalle prese

elettriche tutti i cavi di alimentazione, rimuovere la batteria e poi scollegare
i cavi di interconnessione.

Antes de quitar una FRU, apague el sistema, desenchufe todos los cables de
las tomas de corriente eléctrica, quite la batería y, a continuación, desconecte
cualquier cable de conexión entre dispositivos.

13
 Lenovo Y470/Y570 Hardware Maintenance Manual

Laser compliance statement

Some models of Lenovo computer are equipped from the factory with an optical
storage device such as a CD-ROM drive or a DVD-ROM drive. Such devices are
also sold separately as options. If one of these drives is installed, it is certified in
the U.S. to conform to the requirements of the Department of Health and Human
Services 21 Code of Federal Regulations (DHHS 21 CFR) Subchapter J for Class
1 laser products. Elsewhere, the drive is certified to conform to the requirements
of the International Electrotechnical Commission (IEC) 825 and CENELEC EN 60
825 for Class 1 laser products.

If a CD-ROM drive, a DVD-ROM drive, or another laser device is installed, note

the following:

CAUTION
Use of controls or adjustments or performance of procedures other than
those specified herein might result in hazardous radiation exposure.
O uso de controles, ajustes ou desempenho de procedimentos diferentes
daqueles aqui especificados pode resultar em perigosa exposição à radiação.

Pour éviter tout risque d’exposition au rayon laser, respectez les consignes
de réglage et d’utilisation des commandes, ainsi que les procédures décrites.
Werden Steuer- und Einstellelemente anders als hier festgesetzt verwendet,
kann gefährliche Laserstrahlung auftreten.

L’utilizzo di controlli, regolazioni o l’esecuzione di procedure diverse da

quelle specificate possono provocare l’esposizione a.

El uso de controles o ajustes o la ejecución de procedimientos distintos de los

aquí especificados puede provocar la exposición a radiaciones peligrosas.

Opening the CD-ROM drive, the DVD-ROM drive, or any other optical storage
device could result in exposure to hazardous laser radiation. There are no
serviceable parts inside those drives. Do not open.

14
 Safety information

A CD-ROM drive, a DVD-ROM drive, or any other storage device installed may
contain an embedded Class 3A or Class 3B laser diode. Note the following:

DANGER
Emits visible and invisible laser radiation when open. Do not stare into the
beam, do not view directly with optical instruments, and avoid direct
exposure to the beam.
Radiação por raio laser ao abrir. Não olhe fixo no feixe de luz, não olhe
diretamente por meio de instrumentos óticos e evite exposição direta com o
feixe de luz.

Rayonnement laser si carter ouvert. Évitez de fixer le faisceau, de le regarder

directement avec des instruments optiques, ou de vous exposer au rayon.
Laserstrahlung bei geöffnetem Gerät. Nicht direkt oder über optische
Instrumente in den Laserstrahl sehen und den Strahlungsbereich meiden.
Kinyitáskor lézersugár ! Ne nézzen bele se szabad szemmel, se optikai
eszközökkel. Kerülje a sugárnyalábbal való érintkezést!
Aprendo l’unità vengono emesse radiazioni laser. Non fissare il fascio, non
guardarlo direttamente con strumenti ottici e evitare l’esposizione diretta al
fascio.

Radiación láser al abrir. No mire fijamente ni examine con instrumental

óptico el haz de luz. Evite la exposición directa al haz.

15
 Lenovo Y470/Y570 Hardware Maintenance Manual

Important service information

This chapter presents the following important service information:
• “Strategy for replacing FRUs” on page 16
– “Strategy for replacing a hard disk drive” on page 17
– “Important notice for replacing a system board” on page 17
• “Important information about replacing RoHS compliant FRUs” on page 18

Important:
BIOS and device driver fixes are customer-installable. The BIOS and device
drivers are posted on the customer support site:
http://consumersupport.lenovo.com/.

Strategy for replacing FRUs

Before replacing parts:

Make sure that all software fixes, drivers, and BIOS downloads are installed
before replacing any FRUs listed in this manual.
After a system board is replaced, ensure that the latest BIOS is loaded to the
system board before completing the service action.
To download software fixes, drivers, and BIOS, follow the steps below:
1. Go to http://consumersupport.lenovo.com/.
2. Enter the serial number or select a product or use Lenovo smart
downloading.
3. Select the BIOS/Driver/Applications and download.
4. Follow the directions on the screen and install the necessary software.

16
 Important service information

Use the following strategy to prevent unnecessary expense for replacing and
servicing FRUs:
• If you are instructed to replace an FRU, but the replacement does not solve
the problem, reinstall the original FRU before you continue.
• Some computers have both a processor board and a system board. If you are
instructed to replace either of them, and replacing one of them does not solve
the problem, reinstall that board, and then replace the other one.
• If an adapter or a device consists of more than one FRU, any of the FRUs may
be the cause of the error. Before replacing the adapter or device, remove the
FRUs one by one to see if the symptoms change. Replace only the FRU that
changed the symptoms.
Attention: The setup configuration on the computer you are servicing may have
been customized. Running Automatic Configuration may alter the settings. Note
the current configuration settings (using the View Configuration option); then,
when service has been completed, verify that those settings remain in effect.

Strategy for replacing a hard disk drive

Always try to run a low-level format before replacing a hard disk drive. This will
cause all customer data on the hard disk to be lost. Make sure that the customer
has a current backup of the data before performing this action.
Attention: The drive startup sequence in the computer you are servicing may
have been changed. Be extremely careful during write operations such as
copying, saving, or formatting. If you select an incorrect drive, data or programs
can be overwritten.

Important notice for replacing a system board

Some components mounted on a system board are very sensitive. Improper
handling can cause damage to those components, and may cause a system
malfunction.
Attention: When handling a system board:
• Do not drop the system board or apply any excessive force to it.
• Avoid rough handling of any kind.
• Avoid bending the system board and hard pushing to prevent cracking at
each BGA (Ball Grid Array) chipset.

17
 Lenovo Y470/Y570 Hardware Maintenance Manual

Important information about replacing RoHS compliant FRUs

RoHS, The Restriction of Hazardous Substances in Electrical and

Electronic Equipment Directive (2002/95/EC) is a European Union legal
requirement affecting the global electronics industry. RoHS requirements
must be implemented on Lenovo products placed on the market after June
2006. Products on the market before June 2006 are not required to have
RoHS compliant parts. If the original FRU parts are non-compliant,
replacement parts can also be non-compliant. In all cases if the original
FRU parts are RoHS compliant, the replacement part must also be RoHS
compliant.

Note: RoHS and non-RoHS FRU part numbers with the same fit and function are
identified with unique FRU part numbers.

Lenovo plans to transit to RoHS compliance well before the implementation date
and expects its suppliers to be ready to support Lenovo’s requirements and
schedule in the EU. Products sold in 2005 and 2006 will contain some RoHS
compliant FRUs. The following statement pertains to these products and any
product Lenovo produces containing RoHS compliant FRUs.

RoHS compliant FRUs have unique FRU part numbers. Before or after the RoHS
implementation date, failed RoHS compliant parts must always be replaced with
RoHS compliant ones, so only the FRUs identified as compliant in the system
HMM or direct substitutions for those FRUs may be used.

Products marketed before June 2006 Products marketed after June 2006
Current or Replacement Current or Replacement
original part FRU original part FRU
Non-RoHS Can be Non-RoHS
Non-RoHS Can be RoHS
Must be RoHS Must be RoHS
Non-RoHS Can sub to RoHS
RoHS Must be RoHS

Note: A direct substitution is a part with a different FRU part number that is
automatically shipped by the distribution center at the time of the order.

18
 General checkout

General checkout
This chapter presents the following information:
• “What to do first” on page 20
• “Power system checkout” on page 21

Before you go to the checkout, make sure to read the following important notes:

Important notes:
• Only certified trained personnel can service the computer.
• Before replacing any FRU, read the entire page on removing and
replacing FRUs.
• When you replace FRUs, use new nylon-coated screws.
• Be extremely careful during such write operations as copying,
saving, or formatting. Drives in the computer that you are servicing
sequence might have been altered. If you select an incorrect drive, data
or programs might be overwritten.
• Replace an FRU only with another FRU of the correct model. When
you replace an FRU, make sure that the machine model and the FRU part
number are correct by referring to the FRU parts list.
• An FRU should not be replaced just because of a single,
unreproducible failure. Single failures can occur for a variety of reasons
that have nothing to do with a hardware defect, such as cosmic radiation,
electrostatic discharge, or software errors. Consider replacing an FRU
only when a problem recurs. If you suspect that an FRU is defective,
clear the error logs and run the test again. If the error does not recur, do
not replace the FRU.
• Be careful not to replace a nondefective FRU.

19
 Lenovo Y470/Y570 Hardware Maintenance Manual

What to do first

When you do return an FRU, you must include the following information in the
parts exchange form or parts return form that you attach to it:
1. Name and phone number of servicer
2. Date of service
3. Date on which the machine failed
4. Date of purchase
5. Procedure index and page number in which the failing FRU was detected
6. Failing FRU name and part number
7. Machine type, model number, and serial number
8. Customer’s name and address

Note for warranty: During the warranty period, the customer may be
responsible for repair costs if the computer damage was caused by misuse,
accident, modification, unsuitable physical or operating environment, or
improper maintenance by the customer.
The following is a list of some common items that are not covered under
warranty and some symptoms that might indicate that the system was subjected
to stress beyond normal use.
Before checking problems with the computer, determine whether the damage is
covered under the warranty by referring to the following list:

The following are not covered under warranty:

• LCD panel cracked from the application of excessive force or from being
dropped
• Scratched (cosmetic) parts
• Distortion, deformation, or discoloration of the cosmetic parts
• Plastic parts, latches, pins, or connectors that have been cracked or broken by
excessive force
• Damage caused by liquid spilled into the system
• Damage caused by the improper insertion of a PC Card or the installation of
an incompatible card
• Improper disk insertion or use of an optical drive
• Diskette drive damage caused by pressure on the diskette drive cover, foreign
material in the drive, or the insertion of a diskette with multiple labels
• Damaged or bent diskette eject button
• Fuses blown by attachment of a nonsupported device
• Forgotten computer password (making the computer unusable)
• Sticky keys caused by spilling a liquid onto the keyboard
• Use of an incorrect AC adapter on laptop products

The following symptoms might indicate damage caused by nonwarranted

activities:
• Missing parts might be a symptom of unauthorized service or modification.
• If the spindle of a hard disk drive becomes noisy, it may have been subjected
to excessive force, or dropped.

20
 General checkout

Power system checkout

To verify a symptom, follow the steps below:

1. Turn off the computer.
2. Remove the battery pack.
3. Connect the AC adapter.
4. Make sure that power is supplied when you turn on the computer.
5. Turn off the computer.
6. Disconnect the AC adapter and install the charged battery pack.
7. Make sure that the battery pack supplies power when you turn on the
computer.

If you suspect a power problem, see the appropriate one of the following power
supply checkouts:
• “Checking the AC adapter” on page 21
• “Checking operational charging” on page 21
• “Checking the battery pack” on page 22

Checking the AC adapter

You are here because the computer fails only when the AC adapter is used.
• If the power-on indicator does not turn on, check the power cord of the AC
adapter for correct continuity and installation.
• If the computer does not charge during operation, go to “Checking
operational charging”.
To check the AC adapter, follow the steps below:
1. Unplug the AC adapter cable from the computer.
2. Measure the output voltage at the plug of the AC adapter cable. See the
following figure:

Pin Voltage (V DC)

1 +20

2 0

2
1

Note: Output voltage for the AC adapter pin No. 2 may differ from the one you
are servicing.
3. If the voltage is not correct, replace the AC adapter.
4. If the voltage is acceptable, do the following:
• Replace the system board.
• If the problem persists, go to “Lenovo Y470/Y570” on page 27.
Note: Noise from the AC adapter does not always indicate a defect.

Checking operational charging

To check whether the battery charges properly during operation, use a
discharged battery pack or a battery pack that has less than 50% of the total
power remaining when installed in the computer.

21
 Lenovo Y470/Y570 Hardware Maintenance Manual

Perform operational charging. If the battery status indicator or icon does not
light on, remove the battery pack and let it return to room temperature. Reinstall
the battery pack. If the charge indicator or icon is still off, replace the battery
pack.

If the charge indicator still does not light on, replace the system board. Then
reinstall the battery pack. If it is still not charged, go to the next section.

Checking the battery pack

Battery charging does not start until the Power Meter shows that less than 95%
of the total power remains; under this condition the battery pack can charge to
100% of its capacity. This protects the battery pack from being overcharged or
from having a shortened life.

To check your battery, move your cursor to the Power Meter icon in the icon tray
of the Windows® taskbar and wait for a moment (but do not click it), and the
percentage of battery power remaining is displayed. To get detailed information
about the battery, double-click the Power Meter icon.

Note: If the battery pack becomes hot, it may not be able to be charged. Remove
it from the computer and leave it at room temperature for a while. After it cools
down, reinstall and recharge it.

To check the battery pack, follow the steps below:

1. Turn off the computer.
2. Remove the battery pack and measure the voltage between battery terminals
1 (+) and 7 (-). See the following figure:

Terminal Voltage (V DC)

1 +0 to +14
7(-)
6(-)
5 7 Ground (-)
3 4
2(+)
1(+)
3. If the voltage is less than +11.0 V DC, the battery pack has been discharged.
Note: Recharging will be continued for at least 3 hours, even though the
indicator does not light on.
If the voltage is still less than +11.0 V DC after recharging, replace the battery.
4. If the voltage is more than +11.0 V DC, measure the resistance between
battery terminals 5 and 7. The resistance must be 4 to 30 KΩ.
If the resistance is not correct, replace the battery pack. If the resistance is
correct, replace the system board.

22
 Related service information

Related service information

This chapter presents the following information:
• “Restoring the factory contents by using Recovery Disc Set” on page 23
• “Passwords” on page 24
• “Power management” on page 25

Restoring the factory contents by using Recovery Disc Set

When the hard disk drive or solid state drive is replaced because of a failure, no
product recovery program is on the new drive. In this case, you must use the
Recovery Disc Set for the computer. Order the Recovery Disc Set and the drive at
the same time so that you can recover the new drive with the pre-installed
software when they arrive.
The Recovery Disc Set consists of the following set of DVDs to restore the
computer to the original factory configuration.

Start Recovery Disc (one disc)

This disc is used to format the hard disk drive and initiate the recovery process.

Operating System Recovery Disc (one or more discs)

This disc restores the Microsoft Windows operating system.

Applications and Drivers Recovery Disc (one or more discs)

This disc restores the pre-installed applications and drivers on the computer.

Supplemental Recovery Disc

This disc contains additional content, such as software for specific models and
updates to the software that was preloaded on the computer. Not all recovery
disc sets come with a Supplemental Recovery Disc.

To restore the computer to the original factory configuration using the recovery
disc set, do the following:
1. Insert the bootable Start Recovery Disc into the optical drive.
2. Start the computer. When the Lenovo logo comes up, immediately press F12;
on the boot sequence menu, select the optical drive as the first boot-up device.
The computer will boot from the Start Recovery Disc. Follow the on-screen
instructions to begin the recovery process.
3. Read the license. If you agree with the terms, select I accept these terms and
conditions and then click Next.
4. Insert the Operating System Recovery Disc when prompted and click Yes to
begin the operating system recovery process.
5. Insert the Applications and Drivers Recovery Disc when prompted and then
click OK to begin the applications and drivers recovery process.
6. If you have a Supplemental Recovery Disc, insert it when prompted and click
Yes. If you do not have a Supplemental Recovery Disc, click No.

23
 Lenovo Y470/Y570 Hardware Maintenance Manual

7. When all of the data has been copied from the last disc in the set, remove the
disc and restart the computer.

Note: The remainder of the recovery process is fully automated and no

action is required by you. The computer will restart into the Windows
desktop several times and you might experience periods when no activity is
apparent on the screen for several minutes at a time. This is normal.

8. When the recovery process is complete, the Welcome to the Microsoft

Windows screen is displayed. Follow the instructions on the screen to
complete the Windows setup.

Passwords

As many as three passwords may be needed for any Lenovo computer: the
power-on password (POP), the hard disk password (HDP), and the supervisor
password (SVP).
If any of these passwords has been set, a prompt for it appears on the screen
whenever the computer is turned on. The computer does not start until the
password is entered.
Exception: If only an SVP is installed, the password prompt does not appear
when the operating system is booted.

Power-on password
A power-on password (POP) protects the system from being powered on by an
unauthorized person. The password must be entered before an operating system
can be booted.

Hard-disk password
There are two hard-disk passwords (HDPs):
+ User HDP - for the user
+ Master HDP - for the system administrator, who can use it to get access to the
hard disk drive even if the user has changed the user HDP
Attention: If the user HDP has been forgotten, check whether a master HDP has
been set. If it has, it can be used for access to the hard disk drive. If no master
HDP is available, neither Lenovo nor Lenov authorized service technicians
provide any services to reset either the user or the master HDP, or to recover data
from the hard disk drive. The hard disk drive can be replaced for a scheduled fee.

Supervisor password
A supervisor password (SVP) protects the system information stored in the BIOS
Setup Utility. The user must enter the SVP in order to get access to the BIOS
Setup Utility and change the system configuration.

Attention: If the SVP has been forgotten and cannot be made available to the
servicer, there is no service procedure to reset the password. The system board
must be replaced for a scheduled fee.

24
 Related service information

Power management

Note: Power management modes are not supported for APM operating system.

To reduce power consumption, the computer has three power management

modes: screen blank, sleep (standby), and hibernation.

Screen blank mode

If the time set on the “Turn off monitor” timer in the operating system expires,
the LCD backlight turns off. You can also turn off the LCD backlight by pressing
Fn+F2.

To end screen blank mode and resume normal operation, press any key.

Sleep (standby) mode

When the computer enters sleep (standby) mode, the following events occur in
addition to what occurs in screen blank mode:
• The LCD is powered off.
• The hard disk drive is powered off.
• The CPU stops.

To enter sleep (standby) mode, press Fn+F1.

In certain circumstances, the computer goes into sleep (standby) mode

automatically:
• If a “suspend time” has been set on the timer, and the user does not do any
operation with the keyboard, the hard disk, the parallel connector, or the
diskette drive within that time.
• If the battery indicator is amber, indicating that the battery power is low.
(Alternatively, if Hibernate when battery becomes low has been selected in
the “Power Management Properties” window, the computer goes into
hibernation mode.)

To cause the computer to return from sleep (standby) mode and resume the
operation, do one of the following:
• Press the Fn key.
• Open the lid.
• Turn on the power switch.

Also, in the following event, the computer automatically returns from sleep
(standby) mode and resumes the operation:
• The time set on the resume timer elapses.

Note: The computer does not accept any input immediately after it enters sleep
(standby) mode. Wait a few seconds before taking any action to reenter
operation mode.

25
 Lenovo Y470/Y570 Hardware Maintenance Manual

Hibernation mode
In hibernation mode, the following occurs:
• The system status, RAM, VRAM, and setup data are stored on the hard disk.
• The system is powered off.

To cause the computer to enter hibernation mode, follow the steps below:
• If you are using the ACPI operating system and have defined one of the
following actions as the event that causes the system to go into hibernation
mode, perform that action:
– Closing the lid.
– Pressing the power button.

Also, the computer goes into hibernation mode automatically in either of the
following conditions:
• If a “hibernation time” has been set on the timer, and if the user does not do
any operation with the keyboard, the hard disk drive, the parallel connector,
or the diskette drive within that time.
• If the timer conditions are satisfied in suspend mode.

When the power is turned on, the computer returns from hibernation mode and
resumes operation. The hibernation file in the boot record on the hard disk drive
is read, and system status is restored from the hard disk drive.

26
 Lenovo Y470/Y570

Lenovo Y470/Y570
This chapter presents the following product-specific service references and
product-specific parts information:
• “Specifications” on page 27
• “Status indicators” on page 29
• “FRU tests” on page 31
• “Fn key combinations” on page 31
• “FRU replacement notices” on page 32
• “Removing and replacing an FRU” on page 33
• “Locations” on page 74
• “Parts list” on page 77

Specifications

The following table lists the specifications of the Lenovo Y470/Y570:

Table 1. Specifications
Feature Description
Processor • Intel Huron River
Core Chipset • Intel HM65
Bus architecture • DDR3: 800, 1066, 1333MT/s for Dual Core CPU
• DDR3: 800, 1066, 1333MT/s for Quad Core CPU (Y470)
• DDR3: 800, 1066, 1333, 1600MT/s for Quad Core CPU
(Y570)
• DMI × 4, 2.5Gb/s
• FDI 8 lanes (2channels), 2.7Gt/s
• PCI Express
Graphic Chipset • Intel integrated
• Nvidia N12P-GT (Y470)
• NVIDIA N12P-GT1 (Y570)
Display • 14.0 HD WLED Panel, gloss Flat type, 1366×768 pixels,
220 nit (Y470)
• 15.6 HD LED Panel, Wedge type, 1366×768 pixels,
220 nit (Y570)
Standard • DDR3 1333 SODIMM (×2), Support Dual Channel
memory
CMOS RAM • 256 bytes
Hard disk drive • 2.5" SATA 250/320/500GB (5400rpm)
• 2.5" SATA 320/500/750GB (7200rpm)
Solid-state drive • 32G/64G, (Select models only)
Optical drive • 9.5 mm tray-in DVD Rambo/Blue Ray Combo/Rambo

27
 Lenovo Y470/Y570 Hardware Maintenance Manual

Table 1. Specifications (continued)

Feature Description
I/O port • External monitor connector
• Stereo headphone jack
• Microphone jack
• RJ45 × 1
• USB 2.0 × 2 + E-SATA + USB combo × 1
• 6-in-1 card reader
MODEM slot • N/A
TV • N/A (Y470)
• DVB-T/ATSC/DMB-T (Y570)
Audio • 1/8" Stereo Headphone Output Jack
• 1/8" Input Jack Microphone
• Built-in stereo speakers
• Built-in microphone
Video • CRT port × 1
• HDMI port × 1
Ethernet (on the
• 10/100/1000 Ethernet
system board)
PCI Express Mini • Wimax/WIFI × 1
Card slot • SSD × 1
WLAN • Intel 802.16e Wimax
• Intel 802.11 a/b/g/n WIFI
WWAN • N/A
Bluetooth
• BCM92070 BT2.1 EDR, (Select models only)
wireless
Keyboard • Numberic Keyboard
Touch pad • Two clicks with Dome
Finger Print
• N/A
Reader
Integrated
• 2.0M pixies
camera
Battery • 5600mAh, 6 cell Li-ion Battery, 62Wh
• 4400mAh, 6 cell Li-ion Battery, 48Wh
AC adapter • 90 W/120 W
Pre-installed • Windows Win7 Ultimate/Home premium/Home Basic,
operating system 32/64bit

28
 Lenovo Y470/Y570

Status indicators

The system status indicators below show the computer status:

a b c

d
e
f
g

29
 Lenovo Y470/Y570 Hardware Maintenance Manual

Table 2. Status indicators

Indicator Meaning
a Caps lock White: Caps Lock mode is enabled. You can enter all
alphabetic characters (A-Z) in uppercase without
pressing the Shift key. To enable or disable Caps
Lock mode, press the CapsLk key.
b Num lock White: The separate numeric keypad on the keyboard is
enabled. To enable or disable the numeric keypad,
press the Num Lock key.
c Drive in use White: Data is being read from or written to the hard disk
drive, or the optical disk drive. When this indicator
is on, do not put the computer into standby mode or
turn off the computer.
Note: Do not move the system while the white drive-in-use
light is on. Sudden physical shock could cause drive errors.
d Touchpad White: The touchpad is disabled.

e Power on White: System is enabled.

Blinking white:
System is in sleep mode.
off: System is in hibernate mode or shut down.
f Battery Blinking amber: (500ms off/1s on)
status The remaining power of the battery is less than 5%
of its capacity.
Blinking amber: (100ms off/3.2s on)
The battery is being charged with the remaining
power between 5% and 20% of its capacity.
Amber: The computer is operating on battery power with
the remaining power between 5% and 20% of its
capacity.
Blinking white:
The battery is being charged with the remaining
power between 20% and 80% of its capacity.
White: The remaining power of the battery is more than
80% of its capacity, or the computer is operating on
battery power with the remaining power between
20% and 80% of its capacity.
g Wireless White: The wireless LAN radio is turned on and connected
status to AP.
Blinking white:
The wireless LAN is switched on and the radio of it
is also turned off, or the wireless LAN radio is
turned on and not connected to AP.
Flashing white:
The wireless LAN radio is turned on and data is
being transmitted.
Off: The wireless LAN is switched off and the radio of it
is also turned off.
h GPU switch White: GPU switching is enabled.
indicator

30
 Lenovo Y470/Y570

Fn key combinations

The following table shows the function of each combination of Fn with a function
key.
Table 4. Fn key combinations
Fn + Esc: Turn on/off the integrated camera.
Fn + F1: Enter sleep mode.
Fn + F2: Turn on/off the backlight of the LCD screen.
Fn + F3: Open the interface for the display device switch to
select this notebook or an external display.
Fn + F4: Open the interface for display resolution settings.
Fn + F5: Open the interface for integrated wireless devices
settings (on/off).
Fn + F6: Enable/Disable the touchpad.
Fn + F8 (Y470): Enable/Disable the numeric keypad.
Fn + F9: Start/Pause playback of Windows Media Player.
Fn + F10: Stop playback of Windows Media Player.
Fn + F11: Skip to the previous track.
Fn + F12: Skip to the next track.
Fn + Insert (Y570):
Enable/Disable the scroll lock.
Fn + PgUp (Y470):
Fn + PrtSc: Activate the system request.
Fn + Home: Activate the pause function.
Fn + End: Activate the break function.
Fn + PgDn (Y470): Activate the insert function.
Fn + ↑ / ↓: Increase/Decrease display brightness.
Fn + → / ←: Increase/Decrease sound volume.

31
 Lenovo Y470/Y570 Hardware Maintenance Manual

FRU replacement notices

This section presents notices related to removing and replacing parts. Read this
section carefully before replacing any FRU.

Screw notices
Loose screws can cause a reliability problem. In the Lenovo computer, this
problem is addressed with special nylon-coated screws that have the following
characteristics:
• They maintain tight connections.
• They do not easily come loose, even with shock or vibration.
• They are harder to tighten.
• Each one should be used only once.

Do the following when you service this machine:

• Keep the screw kit in your tool bag.
• Always use new screws.
• Use a torque screwdriver if you have one.

Tighten screws as follows:

• Plastic to plastic
Turn an additional 90° after the screw head touches the surface of the plastic
part:
more than 90°

(Cross-section)

• Logic card to plastic

Turn an additional 180° after the screw head touches the surface of the logic
card:
more than 180°

(Cross-section)

• Torque driver
If you have a torque screwdriver , refer to the “Torque” column for each step.
• Make sure that you use the correct screws. If you have a torque screwdriver,
tighten all screws firmly to the torque shown in the table. Never use a screw
that you removed. Use a new one. Make sure that all screws are
tightened firmly.
• Ensure torque screwdrivers are calibrated correctly following country
specifications.

32
 Lenovo Y470/Y570

Removing and replacing an FRU

This section presents exploded figures with the instructions to indicate how to
remove and replace the FRU. Make sure to observe the following general rules:
1. Do not attempt to service any computer unless you have been trained and
certified. An untrained person runs the risk of damaging parts.
2. Before replacing any FRU, review “FRU replacement notices” on page 32.
3. Begin by removing any FRUs that have to be removed before the failing FRU.
Any of such FRUs are listed at the top of the page. Remove them in the order
in which they are listed.
4. Follow the correct sequence in the steps to remove the FRU, as given in the
figures by the numbers in square callouts.
5. When turning a screw to replace an FRU, turn it in the direction as given by
the arrow in the figure.
6. When removing the FRU, move it in the direction as given by the arrow in the
figure.
7. To put the new FRU in place, reverse the removal procedures and follow any
of the notes that pertain to replacement. For information about connecting
and arranging internal cables, see “Locations” on page 74.
8. When replacing an FRU, use the correct screw as shown in the procedures.

DANGER
Before removing any FRU, turn off the computer, unplug all power cords
from electrical outlets, remove the battery pack, and then disconnect any of
the interconnecting cables.

Attention: After replacing an FRU, do not turn on the computer until you have
made sure that all screws, springs, and other small parts are in place and none
are loose inside the computer. Verify this by shaking the computer gently and
listening for rattling sounds. Metallic parts or metal flakes can cause electrical
short circuits.

Attention: The system board is sensitive to, and can be damaged by, electrostatic
discharge. Before touching it, establish personal grounding by touching a
ground point with one hand or using an electrostatic discharge (ESD) strap
(P/N 6405959) to remove potential shock reasons.

Note: The illustrations used in this section are of the Lenovo Y570, unless
otherwise stated.

33
 Lenovo Y470/Y570 Hardware Maintenance Manual

1010 Battery pack

DANGER
Only use the battery specified in the parts list for your computer. Any other
battery could ignite or explode.

Figure 1. Removal steps of battery pack

Unlock the manual battery latch a. Holding the spring-loaded battery latch in
the unlocked position b, remove the battery pack in the direction shown by the
arrow c.

a
1

When installing: Install the battery pack along the slide rails of the slot. Then
make sure that the battery release lever is in the locked position.

34
 Lenovo Y470/Y570

1020 Dummy card

For access, remove this FRU:

• “1010 Battery pack” on page 34

Figure 2. Removal steps of dummy cards

Remove the dummy card in the direction shown by arrows a b .

1
2

35
 Lenovo Y470/Y570 Hardware Maintenance Manual

1030 Hard disk drive(HDD)/Memory/Mini PCI Express Card

slot compartment cover

For access, remove this FRU:

• “1010 Battery pack” on page 34

Figure 3. Removal steps of HDD/Memory/Mini PCI Express Card slot/TV Card slot
compartment cover
Loosen the screws a that secure the compartment cover. Remove the
compartment cover b .
Y470:

a
a a
a
a

Y570:

a
a a a
a a

b
a

36
 Lenovo Y470/Y570

1040 Hard disk drive

For access, remove these FRUs in order:

• “1010 Battery pack” on page 34
• “1030 Hard disk drive(HDD)/Memory/Mini PCI Express Card slot
compartment cover” on page 36

Attention:
• Do not drop the hard disk drive or apply any physical shock to it.
The hard disk drive is sensitive to physical shock. Improper handling
can cause damages and permanent loss of data.
• Before removing the drive, suggest the customer to backup all the
information on it if possible.
• Never remove the drive while the system is operating or is in suspend
mode.

Figure 4. Removal steps of hard disk drive

Remove the frame fixing screws a .

37
 Lenovo Y470/Y570 Hardware Maintenance Manual

Pull the tab in the direction shown by arrow b .

Take out the hard disk drive secured in a metal frame c .

Step Screw (quantity) Color Torque

a M2.5 × 4 mm, flat-head, nylok-coated Black 1.5 ~ 2.0 kgfcm
(1)
M2.5 × 10 mm, flat-head, nylok-coated Black 1.5 ~ 2.0 kgfcm
(1)

When installing: Make sure that the HDD connector is attached firmly.

38
 Lenovo Y470/Y570

1050 Optical drive

For access, remove this FRU:

• “1010 Battery pack” on page 34

Figure 5. Removal steps of optical drive

Remove the screw a , insert a screwdriver into the screw hole and push the
optical drive in the direction shown by arrow b . Pull the optical drive out in the
direction shown by arrow c.

Step Screw (quantity) Color Torque

a M2.5 × 10 mm, flat-head, nylokcoated Black 1.5 ~ 2.0 kgfcm
(1)

39
 Lenovo Y470/Y570 Hardware Maintenance Manual

1060 DIMM

For access, remove these FRUs in order:

• “1010 Battery pack” on page 34
• “1030 Hard disk drive(HDD)/Memory/Mini PCI Express Card slot
compartment cover” on page 36

Figure 6. Removal steps of DIMM

Release the two latches on both edges of the socket at the same time in the
direction shown by arrows a, and then unplug the DIMM in the direction
shown by arrow b.

a a

Note: If only one DIMM is used on the computer you are servicing, the card must
be installed in SLOT-0 ( : lower slot), but not in SLOT-1 ( : upper slot).
z

When installing: Insert the notched end of the DIMM into the socket. Push the
DIMM firmly, and pivot it until it snaps into the place. Make sure that it is firmly
fixed in the slot and difficult to be moved.

40
 Lenovo Y470/Y570

1070 PCI Express Mini Card for wireless LAN/WAN and TV

Card

For access, remove these FRUs in order:

• “1010 Battery pack” on page 34
• “1030 Hard disk drive(HDD)/Memory/Mini PCI Express Card slot
compartment cover” on page 36

Figure 7. Removal steps of PCI Express Mini Card for wireless LAN/WAN and TV Card
Disconnect the two wireless LAN cables (black, white) a, and then remove the
screw b.
Y470:
b

Y570:
b

In step a, unplug the jacks by using the removal tool antenna RF connector
(P/N: 08K7159), or pick up the connectors with your fingers and gently unplug
them in the direction shown by arrows.

Notes: wireless LAN card has 2 cables in step a .

Wireless LAN card in some models may have 3 cables in step a.

Step Screw (quantity) Color Torque

b M2 × 3 mm, flat-head, nylok-coated (1) Black 1.0 ~ 1.5 kgfcm

41
 Lenovo Y470/Y570 Hardware Maintenance Manual

Figure 7. Removal steps of PCI Express Mini Card for wireless LAN/WAN and TV Card
(continued)
Remove the card in the direction shown by arrow c .
Y470:

Y570:

When installing:
• In models with a wireless LAN card that has two antenna connectors, plug
the black cable (1st) (MAIN) into the jack labeled 1, and the white cable (2nd)
(AUX) into jack labeled 2 on the card.
• In models with a wireless LAN card that has three antenna connectors, plug
the black cable (1st) (MAIN) into the jack labeled 1, the grey cable (3rd) into
jack labeled 3, and the white cable (2nd) (AUX) into jack labeled 2 on the
card.

42
 Lenovo Y470/Y570

Figure 7. Removal steps of PCI Express Mini Card for wireless LAN/WAN and TV Card
Y570: Disconnect the TV card cable d , and then remove the screw e .

e
d

Y570: Remove the card in the direction shown by arrow f .

Step Screw (quantity) Color Torque

e M2.0 × 3 mm, flat-head, nylokcoated Black 1.0 ~ 1.5 kgfcm
(1)

43
 Lenovo Y470/Y570 Hardware Maintenance Manual

1080 Keyboard

For access, remove this FRU:

• “1010 Battery pack” on page 34

Figure 8. Removal steps of keyboard

Y470: Remove eight screws a , four screws b and three screws c .

a
c b
c b b
c b a
a a
a
a
a
a

Y470: Lift the cap sensor board in the direction shown by arrow d.

Step Screw (quantity) Color Torque

a M2.5 × 8 mm, flat-head, nylokcoated(8) Black 1.5 ~ 2.0 kgfcm
b M2.0 × 2 mm, flat-head, nylokcoated(4) Black 1.0 ~ 1.5 kgfcm
c M2.0 × 3 mm, flat-head, nylokcoated(3) Black 1.0 ~ 1.5 kgfcm

44
 Lenovo Y470/Y570

Figure 8. Removal steps of keyboard (continued)

Y470: Remove two screws e . Lift the keyboard a little f, and then detach the
connector in the direction shown by arrow g.

Step Screw (quantity) Color Torque

e M2.0 × 3 mm, flat-head, nylokcoated (2) Black 1.0 ~ 1.5 kgfcm

45
 Lenovo Y470/Y570 Hardware Maintenance Manual

Figure 8. Removal steps of keyboard (continued)

Y570: Remove the screw a.
a

Y570: Loosen the keyboard with fingers in the direction shown by arrow b.

Step Screw (quantity) Color Torque

a M2.5 × 8 mm, flat-head, nylokcoated (1) Black 1.5 ~ 2.0 kgfcm

46
 Lenovo Y470/Y570

Figure 8. Removal steps of keyboard (continued)

Y570: Lift the keyboard a little c , and then detach the connector in the direction
shown by arrow d.

Y570: Lift the keyboard cover in the direction shown by arrow e.

47
 Lenovo Y470/Y570 Hardware Maintenance Manual

Figure 8. Removal steps of keyboard (continued)

Loosen two screws f to remove the power board.

f f

Step Screw (quantity) Color Torque

f M2.0 × 2 mm, flat-head, nylokcoated (2) Black 1.0 ~ 1.5 kgfcm

48
 Lenovo Y470/Y570

1090 Keyboard bezel

For access, remove these FRUs in order:

• “1010 Battery pack” on page 34
• “1030 Hard disk drive(HDD)/Memory/Mini PCI Express Card slot
compartment cover” on page 36
• “1050 Optical drive” on page 39
• “1080 Keyboard” on page 44

Figure 9. Removal steps of keyboard bezel

Y570: Remove twelve screws a , four screws b and three screws c on the
bottom.
aa a
c b
cc bb
a b a
a a a
a
a
a
a

Step Screw (quantity) Color Torque

a M2.5 × 8 mm, flat-head, nylokcoated (12) Black 1.5 ~ 2.0 kgfcm
b M2 × 2 mm, flat-head, nylok-coated (4) Black 1.0 ~ 1.5 kgfcm
c M2 × 3 mm, flat-head, nylok-coated (3) Black 1.0 ~ 1.5 kgfcm

49
 Lenovo Y470/Y570 Hardware Maintenance Manual

Figure 9. Removal steps of keyboard bezel (continued)

Y470: Remove the screw d.

Y570: Remove two screws d .

d
d

Step Screw (quantity) Color Torque

d Y470: M2.5 × 4 mm, flat-head, nylok- Black 1.5 ~ 2.0 kgfcm
coated (1)
Y570: M2.5 × 8 mm, flat-head, nylok- Black 1.5 ~ 2.0 kgfcm
coated (2)

50
 Lenovo Y470/Y570

Figure 9. Removal steps of keyboard bezel (continued)

Y470: Detach and the LCD connector in the direction shown by arrow e and
the FPC connector in the direction shown by arrow f . Unplug the microphone
connector in the direction shown by arrow g .

g
e

Y570: Detach and the LCD connector in the direction shown by arrow e and
the FPC connectors in the direction shown by arrow f .

When installing: Make sure that all the FPC connectors, microphone connectors
and LCD connector are attached firmly.

51
 Lenovo Y470/Y570 Hardware Maintenance Manual

Figure 9. Removal steps of keyboard bezel (continued)

Remove the keyboard bezel in the direction shown by arrow h.

52
 Lenovo Y470/Y570

1100 System board

Important notices for handling the system board:

When handling the system board, bear the following in mind.
• Be careful not to drop the system board on a bench top that has a hard
surface, such as metal, wood, or composite.
• Avoid rough handling of any kind.
• In the whole process, make sure not to drop or stack the system board.
• If you put a system board down, make sure to put it only on a padded
surface such as an ESD mat or conductive corrugated material.

For access, remove these FRUs in order:

• “1010 Battery pack” on page 34
• “1020 Dummy card” on page 35
• “1030 Hard disk drive(HDD)/Memory/Mini PCI Express Card slot
compartment cover” on page 36
• “1040 Hard disk drive” on page 37
• “1050 Optical drive” on page 39
• “1060 DIMM” on page 40
• “1070 PCI Express Mini Card for wireless LAN/WAN and TV Card” on
page 41
• “1080 Keyboard” on page 44
• “1090 Keyboard bezel” on page 49

53
 Lenovo Y470/Y570 Hardware Maintenance Manual

Figure 10. Removal steps of system board

Y470: Loosen the screw a . Unplug three microphone connectors in the
direction shown by arrows b .

1
2

Step Screw (quantity) Color Torque

a M2.0 × 3 mm, flat-head, nylok-coated (1) Black 1.0 ~ 1.5 kgfcm

54
 Lenovo Y470/Y570

Y570: Loosen four screws a . Unplug three microphone connectors in the

direction shown by arrows b .

1 1

When installing: Make sure that all the connectors are attached firmly.

Step Screw (quantity) Color Torque

a M2.5 × 5 mm, flat-head, nylok-coated (4) Black 1.5 ~2.0 kgfcm

55
 Lenovo Y470/Y570 Hardware Maintenance Manual

Figure 10. Removal steps of system board (continued)

Remove the system board in the direction shown by arrow c.

a a

When installing: When attaching the system board to the base cover, adjust the
placement of the wireless radio switch as shown in , and make sure that both
of the audio jack and the microphone jack are attached to the holes on the base
cover as shown in . Improper placement of the switch or those jacks might
cause a damage.

56
 Lenovo Y470/Y570

1110 LCD unit

For access, remove these FRUs in order:

• “1010 Battery pack” on page 34
• “1020 Dummy card” on page 35
• “1030 Hard disk drive(HDD)/Memory/Mini PCI Express Card slot
compartment cover” on page 36
• “1040 Hard disk drive” on page 37
• “1050 Optical drive” on page 39
• “1060 DIMM” on page 40
• “1070 PCI Express Mini Card for wireless LAN/WAN and TV Card” on
page 41
• “1080 Keyboard” on page 44
• “1090 Keyboard bezel” on page 49
• “1100 System board” on page 53

Figure 11. Removal steps of LCD unit

Y470: Remove five screws a and two screws b .

1 1 1 1

2 2 1

Step Screw (quantity) Color Torque

a M2.5 × 6 flat-head, nylok-coated (5) White 1.5 ~2.0 kgfcm
b M2.5 × 4 flat-head, nylok-coated (2) Black 1.5 ~2.0 kgfcm

57
 Lenovo Y470/Y570 Hardware Maintenance Manual

Y570: Release the antenna cables from the cable guides in the direction shown by
arrows a. Remove three screws b.

2
2

1
1

Step Screw (quantity) Color Torque

b M2.5 × 5 mm, flat-head, nylok-coated Black 2.0 ~ 2.5 kgfcm
(3)

When installing:
• Route the antenna cables along the cable guides. As you route the cables,
make sure that they are not subjected to any tension. Tension could cause the
cables to be damaged by the cable guides, or a wire to be broken.
• Make sure that the LCD connector is attached firmly and make sure that you
do not pinch the antenna cables when you attach the LCD assembly. Route
the LCD cable along the cable guides.

58
 Lenovo Y470/Y570

Figure 11. Removal steps of LCD unit (continued)

Remove the LCD unit in the direction shown by arrows c.

59
 Lenovo Y470/Y570 Hardware Maintenance Manual

1120 Fan assembly and Heat Sink assembly

For access, remove these FRUs in order:
• “1010 Battery pack” on page 34
• “1020 Dummy card” on page 35
• “1030 Hard disk drive(HDD)/Memory/Mini PCI Express Card slot
compartment cover” on page 36
• “1040 Hard disk drive” on page 37
• “1050 Optical drive” on page 39
• “1060 DIMM” on page 40
• “1070 PCI Express Mini Card for wireless LAN/WAN and TV Card” on
page 41
• “1080 Keyboard” on page 44
• “1090 Keyboard bezel” on page 49
• “1100 System board” on page 53

Figure 12. Removal steps of fan assembly and heat sink assembly
Y470: Detach the fan connector in the direction shown by arrow a and loosen
six screws b to lift the fan assembly.

2
2
2 2 2

When installing: Make sure that the fan connector is attached firmly to the
system board.

Step Screw (quantity) Color Torque

b M2.0 × 3.2 mm, flat-head, nylok-coated (6) Black 1.0 ~ 1.5 kgfcm

60
 Lenovo Y470/Y570

Figure 12. Removal steps of fan assembly and heat sink assembly (continued)
Y570: Detach the fan connector in the direction shown by arrow a and loosen
seven screws b to lift the fan assembly.

2
2 2
2

2 2
2

Step Screw (quantity) Color Torque

c M2. × 6.5 mm, flat-head, nylok-coated White 1.5 ~ 2,0 kgfcm
(7)

61
 Lenovo Y470/Y570 Hardware Maintenance Manual

1130 CPU

For access, remove these FRUs in order:

• “1010 Battery pack” on page 34
• “1020 Dummy card” on page 35
• “1030 Hard disk drive(HDD)/Memory/Mini PCI Express Card slot
compartment cover” on page 36
• “1040 Hard disk drive” on page 37
• “1050 Optical drive” on page 39
• “1060 DIMM” on page 40
• “1070 PCI Express Mini Card for wireless LAN/WAN and TV Card” on
page 41
• “1080 Keyboard” on page 44
• “1090 Keyboard bezel” on page 49
• “1100 System board” on page 53
• “1120 Fan assembly and Heat Sink assembly” on page 60

Attention: CPU is extremely sensitive. When you service the CPU, avoid any
kind of rough handling.

Figure 13. Removal steps of CPU

Rotate the head of the screw in the direction shown by arrow a to release the
lock, then remove the CPU in the direction shown by arrow b .

When installing: Place the CPU on the CPU socket in the direction shown by
arrow , and then rotate the head of the screw in the direction shown by arrow
to secure the CPU.

62
 Lenovo Y470/Y570

1140 Base cover, speakers and bluetooth card

For access, remove these FRUs in order:

• “1010 Battery pack” on page 34
• “1020 Dummy card” on page 35
• “1030 Hard disk drive(HDD)/Memory/Mini PCI Express Card slot
compartment cover” on page 36
• “1040 Hard disk drive” on page 37
• “1050 Optical drive” on page 39
• “1060 DIMM” on page 40
• “1070 PCI Express Mini Card for wireless LAN/WAN and TV Card” on
page 41
• “1080 Keyboard” on page 44
• “1090 Keyboard bezel” on page 49
• “1110 LCD unit” on page 57
• “1100 System board” on page 53

Figure 14. Removal steps of base cover, speakers and bluetooth card
Loosen four screws a , and then remove the speakers b .
Y470:

a
a

b a

a
b

63
 Lenovo Y470/Y570 Hardware Maintenance Manual

Y570:

1
1
2
1
1
2

Step Screw (quantity) Color Torque

a M2.0 × 2 flat-head, nylok-coated (4) White 1.0 ~ 1.5 kgfcm

Y470: Loosen the screw c , then remove the USB in the direction shown by
arrow d .

3
4

When installing: Make sure that the power connector is attached firmly.

Step Screw (quantity) Color Torque

c M2.0 × 3. mm, flat-head, nylok-coated (1) Black 1.0 ~ 1.5 kgfcm

64
 Lenovo Y470/Y570

Figure 14. Removal steps of base cover and bluetooth card (continued)
Remove the power assembly in the direction shown by arrow e .

Remove the bluetooth card in the direction shown by arrow f .

65
 Lenovo Y470/Y570 Hardware Maintenance Manual

Note: Applying labels to the base cover

The new base cover FRU is shipped with a kit containing labels of several
kinds. When you replace the base cover, you need to apply the following
label:

The following labels need to be peeled off from the old base cover, and need
to be put on the new base cover.
Palm-rest Label
Brazil Label (BT)
BT Label for US/CA/TW or Indonesia Label for BT
Malaysia SIRIM BT Label
Malaysia SIRIM WLAN Label
WLAN Label for BRAZIL or WLAN Label for ISRAEL
WLAN Label for US/CA/TW or WLAN Label for INDONESIA
INDONESIA D-SIDE LABEL
PRC/MTM CODE
COA Label

For some models, you also need to apply one or two FCC labels. Check the
old base cover; if it has one or two FCC labels, find duplicates of them in the
label kit and apply them to the new base cover.

For the location of each label, refer to the following figure:

c f
d e g
h
i

66
 Lenovo Y470/Y570

1150 LCD front bezel

For access, remove these FRUs in order:

• “1010 Battery pack” on page 34
• “1020 Dummy card” on page 35
• “1030 Hard disk drive(HDD)/Memory/Mini PCI Express Card slot
compartment cover” on page 36
• “1040 Hard disk drive” on page 37
• “1050 Optical drive” on page 39
• “1060 DIMM” on page 40
• “1070 PCI Express Mini Card for wireless LAN/WAN and TV Card” on
page 41
• “1080 Keyboard” on page 44
• “1090 Keyboard bezel” on page 49
• “1100 System board” on page 53
• “1110 LCD unit” on page 57

Figure 15. Removal steps of LCD front bezel

Remove two screws a .

Step Screw (quantity) Color Torque

a Y470: M2.0 × 4 mm, flat-head, White 1.0 ~ 1.5 kgfcm
nylokcoated (2)
Y570: M2.5 × 5 mm, flat-head, White 1.5 ~ 2.0 kgfcm
nylokcoated (2)

67
 Lenovo Y470/Y570 Hardware Maintenance Manual

Remove the LCD front bezel in the direction shown by arrows b .

2
2

68
 Lenovo Y470/Y570

1160 LCD panel, LCD cable and hinges

For access, remove these FRUs in order:

• “1010 Battery pack” on page 34
• “1020 Dummy card” on page 35
• “1030 Hard disk drive(HDD)/Memory/Mini PCI Express Card slot
compartment cover” on page 36
• “1040 Hard disk drive” on page 37
• “1050 Optical drive” on page 39
• “1060 DIMM” on page 40
• “1070 PCI Express Mini Card for wireless LAN/WAN and TV Card” on
page 41
• “1080 Keyboard” on page 44
• “1090 Keyboard bezel” on page 49
• “1100 System board” on page 53
• “1110 LCD unit” on page 57
• “1150 LCD front bezel” on page 67

Figure 16. Removal steps of LCD panel, LCD cable and hinges
Y470: Remove four screws a. Unplug the integrated camera connector in the
direction shown by arrow b. Lift the LCD panel in the direction shown by
arrows c.

2 1

1
3

3
3

When installing: Make sure that the connector is attached firmly.

Step Screw (quantity) Color Torque

a M2.0 × 3 mm, flat-head, nylokcoated (4) Black 1.0 ~ 1.5 kgfcm

69
 Lenovo Y470/Y570 Hardware Maintenance Manual

Figure 16. Removal steps of LCD panel, LCD cable and hinges (continued)
Y470: Remove five screws d and the hinges in the direction shown by arrows
e.
4

4 4

4
5

Y570: Remove four screws f . Unplug the integrated camera connector in the
direction shown by arrow g . Lift the LCD panel with hinges in the direction
shown by arrows h .

Step Screw (quantity) Color Torque

d M2.0 × 3 mm, flat-head, nylokcoated (5) Black 1.0 ~ 1.5 kgfcm

70
 Lenovo Y470/Y570

Figure 16. Removal steps of LCD panel, LCD cable and hinges (continued)

Note: The LCD cables are attached to the LCD panel by a metal connector.

Peel off the adhesive tape and detach the connector in the direction shown by
arrow f .

When installing: Make sure that the metal connector is attached firmly.

71
 Lenovo Y470/Y570 Hardware Maintenance Manual

1170 Integrated camera

For access, remove these FRUs in order:

• “1010 Battery pack” on page 34
• “1020 Dummy card” on page 35
• “1030 Hard disk drive(HDD)/Memory/Mini PCI Express Card slot
compartment cover” on page 36
• “1040 Hard disk drive” on page 37
• “1050 Optical drive” on page 39
• “1060 DIMM” on page 40
• “1070 PCI Express Mini Card for wireless LAN/WAN and TV Card” on
page 41
• “1080 Keyboard” on page 44
• “1090 Keyboard bezel” on page 49
• “1100 System board” on page 53
• “1110 LCD unit” on page 57
• “1150 LCD front bezel” on page 67
• “1160 LCD panel, LCD cable and hinges” on page 69

Figure 17. Removal steps of integrated camera

Note: The integrated camera is stuck on the top center of the LCD cover.
Remove the integrated camera from the LCD cover a .

When installing: Stick the integrated camera to the top center of the LCD cover
and ajust the placement of it to make sure the connector is attached firmly.

72
 Lenovo Y470/Y570

1180 Antenna assembly and LCD cover

For access, remove these FRUs in order:

• “1010 Battery pack” on page 34
• “1020 Dummy card” on page 35
• “1030 Hard disk drive(HDD)/Memory/Mini PCI Express Card slot
compartment cover” on page 36
• “1040 Hard disk drive” on page 37
• “1050 Optical drive” on page 39
• “1060 DIMM” on page 40
• “1070 PCI Express Mini Card for wireless LAN/WAN and TV Card” on
page 41
• “1080 Keyboard” on page 44
• “1090 Keyboard bezel” on page 49
• “1100 System board” on page 53
• “1110 LCD unit” on page 57
• “1150 LCD front bezel” on page 67
• “1160 LCD panel, LCD cable and hinges” on page 69

Figure 18. Removal steps of antenna assembly and LCD cover

Peel off the adhesive tapes securing the antenna boards, release the
cables from the cable guide, and then remove the antenna assembly in the
direction shown by arrows a .

When installing: Route the antenna cables along the cable guides and secure the
antenna boards with adhesive tapes. As you route the cables, make sure that they
are not subjected to any tension. Tension could cause the cables to be damaged
by the cable guides, or a wire to be broken.

73
 Lenovo Y470/Y570 Hardware Maintenance Manual

Locations

Front view
a Integrated camera
b Built-in microphone
c Wireless module antennas
d Computer display
e Speaker
f Power button
g OneKey Rescue System button
h System status indicators
i Touchpad
j Memory card slot
k GPU( Graphics Processing Unit) switch (Select models only)
l Integrated wireless device switch (Select models only)
m Thermal management button
n OneKey Theater button
o Volume buttons

c b ab
c
d
h
g
f
o
e
n
m

i e

h
j

k
l

74
 Lenovo Y470/Y570

Right-side view
a Kensington slot
b AC power adapter jack
c Optical drive
d TV-in jack(Select models only)
e USB port
f eSATA/USB combo port
Y470:

1
2
5
3

Y570:

2
3
4
5
5

75
 Lenovo Y470/Y570 Hardware Maintenance Manual

Bottom and Left-side view

a VGA port
b HDMI port
c Fan louvers
d RJ-45 port
e USB port (Y470)
eSATA/USB combo port (Y570)
f USB port
g Microphone jack
h Headphone jack
i Battery latch - spring loaded
j Battery pack
k Battery latch - manual
l Hard disk drive (HDD)/Memory/Mini PCI Express Card slot compartment

9 10
11

1
2
3
4
5
12
7 6
8

76
 Lenovo Y470/Y570

Parts list

This section presents the following service parts:

• “Overall” on page 78
• “LCD FRUs” on page 85
• “Keyboard” on page 88
• “Miscellaneous parts” on page 93
• “AC adapters” on page 94
• “Power cords” on page 95

Notes:
• Each FRU is available for all types or models, unless specific types or
models are specified.

77
 Lenovo Y470/Y570 Hardware Maintenance Manual

Overall

2
3

4
5

b
6
f 8

7
9 9

10 10

Y470 Y570
11

12 13
14
16 15

c h
18
17

19

20

21

e
a d
b

25 22 23
24

78
 Lenovo Y470/Y570

Table 5. Parts list—Overall

No. FRU FRU no. CRU ID

1 LCD unit (see “LCD FRUs” on page 85.)

2 Keyboard (see “Keyboard” on page 88.)
3 PIQY0 KEYBOARD COVER (Y470) 31049917 N
3 PIQY1 KEYBOARD COVER (Y570) 31049885 N
4 PIQY0 POWER BOARD 11013487 N
5 PIQY0 CAP SENSOR BOARD W/CABLE (Y470) 31049916 N
5 PIQY1 CAP SENSOR BOARD W/CABLE (Y570) 31049884 N
6 PIQY0 UPPER CASE W/TP (Y470) 31049922 N
6 PIQY1 UPPER CASE W/TP (Y570) 31049887 N
7 PIQY0 TP BUTTON BOARD W/CABLE 31049919 N
8 PIQY0 TP MODULE MYLAR (Y470) 31049921 N
9 PIQY0 MB OPT 1G QC U2 W/BT/HDMI (Y470) 11013488 N
9 PIQY0 MB OPT 2G DC U3 W/BT/HDMI (Y470) 11013489 N
9 PIQY0 MB OPT 2G QC U2 W/BT/HDMI (Y470) 11013490 N
9 PIQY0 MB OPT 2G DC U2 W/BT/HDMI (Y470) 11013491 N
9 PIQY0 MB OPT 2G QC U3 W/BT/HDMI (Y470) 11013492 N
9 PIQY0 MB OPT 1G DC U3 W/BT/HDMI (Y470) 11013493 N
9 PIQY0 MB OPT 1G QC U3 W/BT/HDMI (Y470) 11013494 N
9 PIQY0 MB OPT 1G DC U2 W/BT/HDMI (Y470) 11013495 N
9 PIQY0 MB OPT 1G QC U2 W/HDMI WO/BT (Y470) 11013496 N
9 PIQY0 MB OPT 2G DC U3 W/HDMI WO/BT (Y470) 11013497 N
9 PIQY0 MB OPT 2G QC U2 W/HDMI WO/BT (Y470) 11013498 N
9 PIQY0 MB OPT 2G DC U2 W/HDMI WO/BT (Y470) 11013499 N
9 PIQY0 MB OPT 2G QC U3 W/HDMI WO/BT (Y470) 11013500 N
9 PIQY0 MB OPT 1G DC U3 W/HDMI WO/BT (Y470) 11013501 N
9 PIQY0 MB OPT 1G QC U3 W/HDMI WO/BT (Y470) 11013502 N
9 PIQY0 MB OPT 1G DC U2 W/HDMI WO/BT (Y470) 11013503 N
9 PIQY1 MB DIS 1G QC U3 W/BT/HDMI WO/TV 11013471 N
(Y570)
9 PIQY1 MB OPT 1G QC U3 W/BT/HDMI WO/TV 11013472 N
(Y570)
9 PIQY1 MB DIS 1G QC U2 W/BT/HDMI WO/TV 11013473 N
(Y570)
9 PIQY1 MB OPT 1G QC U2 W/BT/HDMI WO/TV 11013474 N
(Y570)
9 PIQY1 MB DIS 1G DC U3 W/BT/HDMI WO/TV 11013475 N
(Y570)
9 PIQY1 MB OPT 1G DC U3 W/BT/HDMI WO/TV 11013476 N
(Y570)
9 PIQY1 MB DIS 1G DC U2 W/BT/HDMI WO/TV 11013477 N
(Y570)
9 PIQY1 MB OPT 1G DC U2 W/BT/HDMI WO/TV 11013478 N
(Y570)
9 PIQY1 MB DIS 1G QC U3 W/TV/HDMI WO/BT 11013479 N
(Y570)

79
 Lenovo Y470/Y570 Hardware Maintenance Manual

Table 5. Parts list—Overall (continued)

No. FRU FRU no. CRU ID

9 PIQY1 MB OPT 1G QC U3 W/TV/HDMI WO/BT 11013480 N

(Y570)
9 PIQY1 MB DIS 1G QC U2 W/TV/HDMI WO/BT 11013481 N
(Y570)
9 PIQY1 MB OPT 1G QC U2 W/TV/HDMI WO/BT 11013482 N
(Y570)
9 PIQY1 MB DIS 1G DC U3 W/TV/HDMI WO/BT (Y570) 11013483 N
9 PIQY1 MB OPT 1G DC U3 W/TV/HDMI WO/BT 11013484 N
(Y570)
9 PIQY1 MB DIS 1G DC U2 W/TV/HDMI WO/BT 11013485 N
(Y570)
9 PIQY1 MB OPT 1G DC U2 W/TV/HDMI WO/BT 11013486 N
(Y570)
9 Y570 QC MB-OPT GT1 1GB USB2.0 W/BT TBD N
9 Y570 QC MB-OPT GT1 1GB USB3.0 W/BT TBD N
9 Y570 QC MB-DIS GT1 1GB USB2.0 W/BT TBD N
9 Y570 QC MB-DIS GT1 1GB USB3.0 W/BT TBD N
9 Y570 DC MB-OPT GT1 1GB USB2.0 W/BT TBD N
9 Y570 DC MB-OPT GT1 1GB USB3.0 W/BT TBD N
9 Y570 DC MB-DIS GT1 1GB USB2.0 W/BT TBD N
9 Y570 DC MB-DIS GT1 1GB USB3.0 W/BT TBD N
9 Y570 QC MB-OPT GT1 1GB USB2.0 WO/BT N/TV TBD N
9 Y570 QC MB-OPT GT1 1GB USB3.0 WO/BT N/TV TBD N
9 Y570 QC MB-DIS GT1 1GB USB2.0 WO/BT N/TV TBD N
9 Y570 QC MB-DIS GT1 1GB USB3.0 WO/BT N/TV TBD N
9 Y570 DC MB-OPT GT1 1GB USB2.0 WO/BT N/TV TBD N
9 Y570 DC MB-OPT GT1 1GB USB3.0 WO/BT N/TV TBD N
9 Y570 DC MB-DIS GT1 1GB USB2.0 WO/BT N/TV TBD N
9 Y570 DC MB-DIS GT1 1GB USB3.0 WO/BT N/TV TBD N
10 PIQY0 SD DOOR (Y470) 31049906 N
10 PIQY1 USB BOARD 2.0 W/SWTICH (Y570) 11013467 N
10 PIQY1 USB BOARD 3.0 W/SWTICH (Y570) 11013468 N
10 PIQY1 USB BOARD 2.0 WO/SWITCH (Y570) 11013469 N
10 PIQY1 USB BOARD 3.0 WO/SWITCH (Y570) 11013470 N
11 Intel i7-2820QM 2.30G 8M 4c D2 PGA processor 102001055 N
11 Intel I7-2720QM 2.20G 6M 4c D2 PGA processor 102001071 N
11 Intel I7-2630QM 2.0G 6M 4c D2 PGA processor 102001070 N
11 Intel I7-2620M 2.7G 4M 2c J1 PGA processor 102001069 N
11 Intel I5-2540M 2.6G 3M 2c J1 PGA processor 102001068 N
11 Intel I5-2520M 2.5G 3M 2c J1 PGA processor 102001067 N
11 Intel I5-2410M 2.3G 3M 2c J1 PGA processor 102001066 N
11 Intel I3-2310M 2.1G 3M 2c J1 PGA processor 102001065 N
12 PIQY0 THERMAL MODULE W/FAN FOR DUAL 31049913 N
CORE (Y470)
12 PIQY0 THERMAL MODULE W/FAN FOR QUAD 31049914 N
CORE (Y470)

80
 Lenovo Y470/Y570

Table 5. Parts list—Overall (continued)

No. FRU FRU no. CRU ID

12 PIQY1 THERMAL MODULE FOR DC W/FAN (Y570) 31049881 N

12 PIQY1 THERNAL MODULE FOR QC W/FAN (Y570) 31049882 N
13 DDRIII 1333 1GB, SAM M471B2873FHS-CH9 11011936 **
13 DDRIII 1333 1GB, RAM RMT1910MD66E7F-1333 11012427 **
13 DDRIII 1333 1GB, HYN HMT112S6DFR8C-H9 N0 11012767 **
13 DDRIII 1333 1GB, RAM RMT3010EF48E7W-1333 11012634 **
13 DDRIII 1333 1GB, RAM RMT3010EF48E7L-1333 11012975 **
13 DDRIII 1333 1GB, SHA SY321NG08HBF 11012810 **
13 DDRIII 1333 2GB, SAM M471B5773CHS-CH9 11012630 **
13 DDRIII 1333 2GB, HYN HMT325S6BFR8C-H9 N0 11012197 **
13 DDRIII 1333 2GB, RAM RMT3020EF48E8W-1333 11012633 **
13 DDRIII 1333 2GB, RAM RMT3020EF48E8L-1333 11012974 **
13 DDRIII 1333 2GB, SHA SY321NH08HAF 11012809 **
13 DDRIII 1333 2GB, RAM RMT1950MD58E8F-1333 11012213 **
13 DDRIII 1333 2GB, NAN NT2GC64B88B0NS-CG 11012761 **
13 DDRIII 1333 4GB, SAM M471B5273CH0-CH9 11011934 **
13 DDRIII 1333 4GB, HYN HMT351S6BFR8C-H9 N0 11012199 **
13 DDRIII 1333 4GB, MIC MT16JSF51264HZ-1G4D1 11012320 **
13 DDRIII 1600 1GB, M471B2873FHS-CK0 TBD **
13 DDRIII 1600 2GB, M471B5773CHS-CK0 (2Gb based) TBD **
13 DDRIII 1600 2GB, HMT325S6BFR8C-PB N0 (Rev B/ TBD **
2Gb/44nm)
13 DDRIII 1600 4GB, M471B5273CH0-CK0 TBD **
13 DDRIII 1600 4GB, HMT351S6BFR8C-PB N0 (Rev B/ TBD **
2Gb/44nm)
14 PIQY0 SD DUMMY CARD (Y470) 31049915 **
14 PIQY1 SD DUMMY CARD (Y570) 31049874 **
15 WLAN card, WiFi 2x2 AG (N) + WiMAX, Intel 6250NX 20002321 **
MOW M PCIE NB HMC
15 WLAN card,WiFi 2x2 AG (N) + WiMAX, Intel 6150GX 20002529 **
MOW M PCIE NB HMC
15 WLAN card,WiFi 2x2 AG (N) + WiMAX, Intel 6250GX 20002388 **
MOW M PCIE NB HMC
15 WLAN card,WiFi 1x2 BG (N) + WiMAX, Intel 6150NX 20002484 **
MOW M PCIE NB HMC
15 WLAN card,WiFi 2x2 AGN, Intel 6205N MOW M PCIE 20002533 **
NB HMC
15 WLAN card,WiFi 1x2 BGN, Intel 1000N MOW M PCIE 20002329 **
NB HMC
15 WLAN card,WiFi 3x3 AGN, Cbt RT3593 MOW M PCIE 20002516 **
NB HMC
15 WLAN card,WiFi 2x2 BGN, Cbt BCM43227 MOW M 20002506 **
PCIE NB HMC
15 WLAN card,WiFi 2x2 BGN, Liteon HB97 MOW M PCIE 20002525 **
NB HMC
15 WLAN card,WiFi 1x1 BGN, Cbt BCM4313 MOW M 20002505 **
PCIE NB HMC

81
 Lenovo Y470/Y570 Hardware Maintenance Manual

Table 5. Parts list—Overall (continued)

No. FRU FRU no. CRU ID

15 WLAN card,WiFi 1x1 BGN, Liteon AR9285 HB95 BGN 20002357 **

MOW NB
15 WLAN card,WiFi 2x2 BGN+BT, Cbt BCM43225HMB 20002511 **
BGN+BT HMC
15 WLAN card,WiFi 2x2 BGN+BT, Liteon WB197 20002520 **
BGN+BT HMC
15 WLAN card,WiFi 1x1 BGN+BT, Cbt BCM4313HMGB 20002501 **
BGN+BT HMC
15 WLAN card,WiFi 1x1 BGN+BT, Liteon WB195 20002524 **
BGN+BT HMC
16 PIQY1 TV DOOR(Y570) 31049870 N
17 PIQY1 TV TUNER MODULE DMB-T AVEMADIA 31049875 N
(Y570)
17 PIQY1 TV TUNER MODULE DMB-T YUAN (Y570) 31049876 N
17 PIQY1 TV TUNER MODULE ATSC AVE (Y570) 31049877 N
17 PIQY1 TV TUNER MODULE DVB-T AVE (Y570) 31049878 N
17 PIQY1 TV TUNER MODULE DVB-T YUAN (Y570) 31049879 N
18 Bluetooth card, BT2.1&BT3.0, Fcn BCM92070 BT2.1 20002266 N
EDR Flash U NB
18 Bluetooth card, BT2.1&BT3.0,USI BCM92070 BT2.1 20002326 N
EDR Flash U NB
19 Battery pack,Y470 Pana L10P6F01 3S2P 62Wh bty (IC), 121001154 *
3S2P 6cell
19 Battery pack,Y470 Celx/SDI L10C6F01 3S2P 62Wh bty, 121001074 *
3S2P 6cell
19 Battery pack,Y470 Sanyo L10S6F01 3S2P 62Wh bty, 121001073 *
3S2P 6cell
19 Battery pack,Y470 Pana L10P6Y01 3S2P 48Wh bty (IC), 121001151 *
3S2P 6cell
19 Battery pack,Y470 Pana L10P6Y01 3S2P 48Wh bty (IC), 121001108 *
3S2P 6cell
19 Battery pack,Y470 Pana L10P6Y01 3S2P 48Wh bty (IC), 121001107 *
3S2P 6cell
20 PIQY0 LOWER CASE FOR DC (Y470) 31049926 *
20 PIQY0 LOWER CASE FOE QC (Y470) 31049927 *
20 PIQY1 LOWER CASE W/TV/SWITCH (Y570) 31049890 *
20 PIQY1 LOWER CASE W/TV WO/SWITCH (Y570) 31049891 *
20 PIQY1 LOWER CASE WO/TV W/SWITCH (Y570) 31049892 *
20 PIQY1 LOWER CASE WO/TV/SWITCH (Y570) 31049893 *
21 Hard disk drive, 320G 5400rpm SATA, Hitachi 16004059 *
HTS545032B9A300
21 Hard disk drive, 320G 5400rpm SATA, WD 4K sector 16004853 *
21 Hard disk drive, 320G 5400rpm SATA, HGST 16005024 *
HTS543232A7A384
21 Hard disk drive, 320G 5400rpm SATA, Seagate 16005211 *
ST320LT020
21 Hard disk drive, 320G 5400rpm SATA, Toshiba 16004642 *
MK3265GSX
21 Hard disk drive, 500G 5400rpm SATA, Hitachi 16004058 *
HTS545050B9A300

82
 Lenovo Y470/Y570

Table 5. Parts list—Overall (continued)

No. FRU FRU no. CRU ID

21 Hard disk drive, 500G 5400rpm SATA, WD5000BPVT- 16004846 *

24HXZT1
21 Hard disk drive, 500G 5400rpm SATA, Seagate 16004189 *
ST9500325AS
21 Hard disk drive, 500G 5400rpm SATA, Toshiba 16004643 *
MK5065GSX
21 Hard disk drive, 640G 5400rpm SATA, WD6400BPVT- 16004847 *
24HXZT1
21 Hard disk drive, 640G 5400rpm SATA, Toshiba 16004644 *
MK6465GSX
21 Hard disk drive, 640G 5400rpm SATA, Seagate 16005046 *
ST9640320AS
21 Hard disk drive, 640G 5400rpm SATA, Toshiba 16005335 *
MK6475GSX
21 Hard disk drive, 750G 5400rpm SATA, WD 16004848 *
WD7500BPVT-24HXZT1
21 Hard disk drive, 750G 5400rpm SATA, Seagate 16005333 *
ST9750423AS
21 Hard disk drive, 750G 5400rpm SATA, Toshiba 16005334 *
MK7575GSX
21 Hard disk drive, 320G 7200rpm SATA, Hitachi 16004530 *
HTS725032A9A364
21 Hard disk drive, 320G 7200rpm SATA, Seagate 16004533 *
ST9320423AS
21 Hard disk drive, 320G 7200rpm SATA, WD 16005212 *
WD3200BEKT
21 Hard disk drive, 320G 7200rpm SATA, HGST 16005027 *
HTS723232A7A364
21 Hard disk drive, 320G 7200rpm SATA, Seagate 16005030 *
ST320LT007
21 Hard disk drive, 500G 7200rpm SATA, Hitachi 16004531 *
HTS725050A9A364
21 Hard disk drive, 500G 7200rpm SATA, Seagate 16004532 *
ST9500420AS
21 Hard disk drive, 500G 7200rpm SATA, WD 16004850 *
WD5000BEKT-24KA9T0
21 Hard disk drive, 750G 7200rpm SATA, Seagate 16005332 *
ST9750420AS
21 Hard disk drive, 750G 7200rpm SATA, TBD TBD *
21 Solid-state drive , mSATA 32G,Samsung 16005083 *
MZMPA032HMCD
21 Solid-state drive , mSATA 64G, Samsung 16005084 *
MZMPA064HMDR
21 Solid-state drive , mSATA 64G, Toshiba 16005081 *
THNSNB064GMCJ
21 Solid-state drive , mSATA 128G, Samsung 16005085 *
MZMPA128HMFU
21 Solid-state drive , mSATA 128G, Toshiba 16005082 *
THNSNB128GMCJ
22 PIQY0 HDD MYLAR 31049935 **
23 ODD, 12.7 Rambo Tray, HLDS GT33N Tray in Rambo 25011474 **
23 ODD, 12.7 Rambo Tray, PLDS DS-8A5S Tray in Rambo 25011187 **

83
 Lenovo Y470/Y570 Hardware Maintenance Manual

Table 5. Parts list—Overall (continued)

No. FRU FRU no. CRU ID

23 ODD, 12.7 Rambo Tray, Optiarc AD-7710H Tray in 25011218 **

Rambo
23 ODD, 12.7 Rambo Tray, TSST TS-L633F Tray in Rambo 25011201 **
23 ODD, 12.7 Rambo Tray, PSN UJ8B1 Tray in Rambo 25013478 **
23 ODD, 12.7 Rambo Tray, PSN UJ8A0 Tray in Rambo 25011472 **
23 ODD, 12.7 BD Combo Tray, HLDS GT33N Tray in 25011473 **
Rambo
23 ODD, 12.7 BD Combo Tray, HLDS GT33N Tray in 25011471 **
Rambo
23 ODD, 12.7 BD Combo Tray, HLDS GT33N Tray in 25011217 **
Rambo
23 ODD, 12.7 BD Rambo Tray, PSN UJ240AF Tray in BD 25011518 **
Rambo
23 ODD, 12.7 BD Rambo Tray, Optiarc BD-5740H Tray in 25011517 **
BD Rambo
24 PIQY0 ODD PANEL BLUE-RAY (Y470) 31049910 **
24 PIQY0 ODD PANEL RAMBO (TRAY IN) (Y470) 31049909 **
24 PIQY1 ODD PANEL RAMBO (TRAY IN) (Y570) 31049872 **
24 PIQY1 ODD PANEL BLUE-RAY (Y570) 31049873 **
25 PIQY0 THERMAL DOOR FOR QUAD CORE (Y470) 31049907 N
25 PIQY0 THERMAL DOOR FOR DUAL CORE (Y470) 31049908 N
25 PIQY1 THERMAL DOOR (Y570) 31049871 N

84
 Lenovo Y470/Y570

LCD FRUs
In Lenovo Y470/Y570, there are following types of LCDs.
• “14.0-in. HD TFT” Y470
• “15.6-in. HD TFT” Y570

8
7

10

10

85
 Lenovo Y470/Y570 Hardware Maintenance Manual

14.0-in. HD TFT (Y470)

Table 6. Parts list—14.0-in. HD TFT

No. FRU FRU no. CRU ID

1 PIQY0 LCD BEZLE W/CAREMA HOLE 31049928 N

3 14.0 HD LED Panel, AUO B140XW03 V0 HD G LED1 18003943 N
NB
3 14.0 HD LED Panel, CMI N140BGE-L41 HD G F CE 18004804 N
LED1 NB
3 14.0 HD LED Panel, LGD LP140WH2-TLQ1 HD G 18003937 N
LED1 NB
3 14.0 HD LED Panel, SEC LTN140AT20-L01 HD G F CE 18004803 N
LED1 NB
3 14.0 HD LED Panel, BOE HT140WXB-300 HD G F CE 18004802 N
LED1 NB
3 14.0 HD LED Panel, CPT CLAA140WB01AJ HD G F CE 18004801 N
LED1 NB
4 PIQY0 LCD HINGE L+R 31049929 N
7 PIQY0 CAMERA 2.0M 31049934 N
8 PIQY0 LVDS CABLE 30PIN 31049930 N
9 PIQY0 LCD COVER W/LOGO 31049933 N
10 PIQY0 ANNTAN FOR WIFI/WIMAX 31049931 N
10 PIQY0 ANNTAN FOR WIFI/WIMAX/MIMO 31049932 N

86
 Lenovo Y470/Y570

15.6-in. HD TFT (Y570)

Table 7. Parts list—15.6-in. HD TFT

No. FRU FRU no. CRU ID

1 PIQY1 LCD BEZLE W/3D Remoter 31049897 N

1 PIQY1 LCD BEZEL WO/3D Remoter 31049898 N
2 PIQY1 SCREW MYLAR 31049894 N
3 15.6 HD LED Panel, AUO B156XW02 V2 HD G LED1 18003797 N
NB
3 15.6 HD LED Panel, CMI N156BGE-L21 HD G W LED1 18004787 N
NB
3 15.6 HD LED Panel, LGD LP156WH4-TLA1 HD G W 18004786 N
LED1 NB
3 15.6 HD LED Panel, SEC LTN156AT16-L01 HD G W 18004785 N
LED1 NB
3 15.6 HD LED Panel, CPT CLAA156WB11A HD G W 18004563 N
LED1 NB
3 15.6 HD LED 3D Panel, CMI N156B6-L3D HD G LED1 18004608 N
NB
3 15.6 HD LED 3D Panel, CPT CLAA156WS01A HD G 18004609 N
LED1 NB
4 PIQY1 LCD HINGE L+R 31049899 N
5 PIQY1 IR MODULE 31049895 N
6 PIQY1 IR CABLE 31049896 N
7 PIQY0 CAMERA 2.0M 31049934 N
8 PIQY1 LVDS CABLE 30PIN 31049901 N
8 PIQY1 LVDS CABLE 40PIN FOR 3D PANEL 31049902 N
9 PIQY1 LCD COVER W/LOGO FOR NON-3D 31049903 N
9 PIQY1 LCD COVER W/LOGO FOR 3D TBD N
10 PIQY1 ANTENNA FOR WIFI/WIMAX 31049904 N
10 PIQY1 ANTENNA FOR WIFI/WIMAX/MIMO 31049905 N

87
 Lenovo Y470/Y570 Hardware Maintenance Manual

Keyboard
Table 8. Parts list—Keyboard

Language P/N CRU ID

English 25012027 **
U.K. English 25012100 **
Italian 25012099 **
Spanish 25012098 **
Turkish 25012097 **
Thai 25012096 **
Portuguese 25012095 **
Latin 25012094 **
Canadian English&French 25012093 **
Korean 25012092 **
Traditional Chinese 25012091 **
Russian 25012045 **
French 25012044 **
German 25012043 **
Chicony Arabic 25012042 **
Brazilian 25012041 **
Japanese 25012040 **
Dutch 25012039 **
Greek 25012038 **
Hebrew 25012037 **
Hungarian 25012036 **
Four Nordic countries 25012035 **
Y470
Belgian 25012034 **
Icelandic 25012033 **
Slovenian 25012032 **
Swiss 25012031 **
International English 25012030 **
Czechoslovakian 25012029 **
Bulgarian 25012028 **
English 25012136 **
U.K. English 25012760 **
Italian 25012759 **
Spanish 25012758 **
Turkish 25012757 **
Thai 25012756 **
Portuguese 25012755 **
Sunrex Latin 25012754 **
Canadian English&French 25012753 **
Korean 25012752 **
Traditional Chinese 25012751 **
Russian 25012750 **
French 25012749 **
German 25012748 **
Arabic 25012747 **

88
 Lenovo Y470/Y570

Table 8. Parts list—Keyboard

Language P/N CRU ID

Brazilian 25012746 **
Dutch 25012744 **
Greek 25012743 **
Hebrew 25012742 **
Hungarian 25012741 **
Four Nordic countries 25012740 **
Y470 Sunrex
Belgian 25012739 **
(continued) (continued)
Icelandic 25012738 **
Slovenian 25012737 **
Swiss 25012736 **
International English 25012735 **
Czechoslovakian 25012734 **
Bulgarian 25012733 **
English 25012135 **
U.K. English 25012710 **
Italian 25012709 **
Spanish 25012708 **
Turkish 25012707 **
Thai 25012706 **
Portuguese 25012705 **
Latin 25012704 **
Canadian English&French 25012703 **
Korean 25012702 **
Traditional Chinese 25012701 **
Russian 25012700 **
French 25012699 **
German 25012698 **
Y470 Darfon
Arabic 25012697 **
Brazilian 25012696 **
Dutch 25012694 **
Greek 25012693 **
Hebrew 25012692 **
Hungarian 25012691 **
Four Nordic countries 25012690 **
Belgian 25012689 **
Icelandic 25012688 **
Slovenian 25012687 **
Swiss 25012686 **
International English 25012685 **
Czechoslovakian 25012684 **
Bulgarian 25012683 **

89
 Lenovo Y470/Y570 Hardware Maintenance Manual

Table 8. Parts list—Keyboard (continued)

Language P/N CRU ID

Bulgarian 25013388 **
Czechoslovakian 25013389 **
International English 25013390 **
Swiss 25013391 **
Slovenian 25013392 **
Icelandic 25013393 **
Italian 25013413 **
Four Nordic countries 25013395 **
Hungarian 25013396 **
Hebrew 25013397 **
Greek 25013398 **
Dutch 25013399 **
Brazilian 25013400 **
Y470 NMB Arabic 25013401 **
(continued) (continued) German 25013402 **
French 25013403 **
Russian 25013404 **
Traditional Chinese 25013405 **
Korean 25013406 **
Canadian English&French 25013407 **
Latin 25013408 **
Portuguese 25013409 **
Thai 25013410 **
Turkish 25013411 **
Spanish 25013412 **
Belgian 25013394 **
U.K. English 25012762 **
English 25012763 **

90
 Lenovo Y470/Y570

Keyboard
Table 8. Parts list—Keyboard

Language P/N CRU ID

English 25011801 **
U.K. English 25011800 **
Italian 25011799 **
Spanish 25011798 **
Turkish 25011796 **
Thai 25011795 **
Portuguese 25011794 **
Latin 25011793 **
Canadian English&French 25011792 **
Korean 25011791 **
Traditional Chinese 25011790 **
Russian 25011789 **
French 25011788 **
German 25011787 **
Chicony Arabic 25011786 **
Brazilian 25011785 **
Japanese 25011784 **
Dutch 25011783 **
Greek 25011782 **
Hebrew 25011781 **
Y570 Hungarian 25011780 **
Four Nordic countries 25011779 **
Belgian 25011778 **
Icelandic 25011777 **
Slovenian 25011776 **
Swiss 25011775 **
International English 25011774 **
Czechoslovakian 25011772 **
Bulgarian 25011773 **
Bulgarian 25011714 **
Czechoslovakian 25011715 **
International English 25011716 **
Swiss 25011717 **
Slovenian 25011718 **
Icelandic 25011719 **
Darfon
Italian 25011720 **
Four Nordic countries 25011721 **
Hungarian 25011722 **
Hebrew 25011723 **
Greek 25011724 **
Dutch 25011725 **

91
 Lenovo Y470/Y570 Hardware Maintenance Manual

Table 8. Parts list—Keyboard

Language P/N CRU ID

Brazilian 25011727 **
Arabic 25011728 **
German 25011729 **
French 25011730 **
Russian 25011731 **
Traditional Chinese 25011732 **
Korean 25011733 **
Y570 Darfon Canadian English&French 25011713 **
(continued) (continued) Latin 25011734 **
Portuguese 25011735 **
Thai 25011736 **
Turkish 25011737 **
Spanish 25011738 **
Belgian 25011739 **
U.K. English 25011740 **
English 25011741 **

92
 Lenovo Y470/Y570

Miscellaneous parts
Table 9. Parts list—Miscellaneous parts

FRU P/N CRU ID

System miscellaneous parts: N

• (a) PIQY0 HDD BRACKET 31049912
• (b) PIQY0 ODD BRACKET 31049911
Cable miscellaneous parts: N
• (c) PIQY1 TV CABLE (Y570) 31049900
• (d) PIQY0 USB CABLE (Y470) 31049924
• (e) PIQY0 DC-IN CABLE (Y470) 31049923
• (e) PIQY1 DC-IN CABLE (Y570) 31049889
• (f) PIQY0 TP CABLE (Y470) 31049920
• (f) PIQY1 TP CABLE (Y570) 31049886
• (g) PIQY0 POWER BOARD CABLE (Y470) 31049918
• (g) PIQY1 POWER BOARD CABLE (Y570) 31049883
• (h) PIQY0 BLUETOOTH CABLE (Y470) 31049925
• (h) PIQY1 BLUETOOTH CABLE (Y570) 31049880
Note: Italicized letters in parentheses are references to the
exploded view in “Overall” on page 71.

93
 Lenovo Y470/Y570 Hardware Maintenance Manual

AC adapters
Table 10. Parts list—3-pin AC adapters

FRU P/N CRU ID

65W, Delta ADP-65KH BD 20V/3.25A adapter 36001929 N

65W, Liteon PA-1650-56LC adapter 36001651 N
65W, Brazil PA-1650-52LB 36001714 N
65W, Chicony CPA-A065 20V3.25A adapter 36001943 N

94
 Lenovo Y470/Y570

Power cords
A Lenovo power cord for a specific country or region is usually available only in
that country or region:
Table 11. Parts list—3-pin power cords

Region P/N CRU ID

CCC 145000602 *
• SSD YD-118-1+IEC53RVV+SSD-3-2B-1 1m
CCC 145000600 *
• LINETEK PC323+RVV300/300+LS15 1m
Argentina 145000599 *
• LINETEK LS15+H03VV-F+LP39 1m
Danmark 145000598 *
• LINETEK LS15+H03VV-F+LP-38 1m
Switzerland 145000597 *
• LINETEK LS15+H03VV-F+LP-37 1m
Brazil 145000596 *
• LINETEK LS15 H03VV-F LP26A 1m
Israel 145000595 *
• LINETEK LS15+H03VV-F+LP-41 1m
UL 145000594 *
• LINETEK LP-30B + SPT-2 + LS15 1m
UK 145000593 *
• LINETEK LP-61L+ H03VV-F+ LS15 1m
Indian 145000592 *
• LINETEK PE-361+ H05VV-F+ LS15 1m
Italy 145000591 *
• LINETEK LS15+H03VV-F+PE-336 1m
Korea 145000590 *
• LINETEK LS15+H05VV-F+LP-E04A 1m
Australia 145000589 *
• LINETEK LS15+H03VV-F+LP-23A 1m
Taiwan 145000588 *
• LINETEK LS15+VCTF+LP-53 1m
Japan 145000587 *
• LINETEK LS15+VCTF+LP-54 1m
Africa 145000586 *
• LINETEK LS15+H03VV-F+PE-364 1m
CE 145000585 *
• LINETEK LP-34+H03VV-F + LS15 1m
Argentina 145000567 *
• Longwell LP-24+H03VV-F+LS-18 1m
Danmark 145000566 *
• Longwell LP-40+H03VV-F+LS-18 1m
Switzerland 145000565 *
• Longwell LP-37+H03VV-F+LS-18 1m

95
 Lenovo Y470/Y570 Hardware Maintenance Manual

Table 11. Parts list—3-pin power cords (continued)

Region P/N CRU ID

Brazil 145000564 *
• Longwell LP-46+H03VV-F+LS-18 1m
Israel 145000563 *
• Longwell LP-41+H03VV-F+LS-18 1m
UL 145000562 *
• Longwell LP-30B+SPT-2 18AWG+LS-18 1m
UK 145000561 *
• Longwell LP-61L+H03VV-F+LS-18 1m
Indian 145000560 *
• Longwell LP-67+BIS+LS-18 1m
Italy 145000559 *
• Longwell LP-22+H03VV-F+LS-18 1m
Korea 145000558 *
• Longwell LP-486+KTLH03VV-F+LS-5 1m
Australia 145000557 *
• Longwell LP-23A+LFC-3R+LS-18 1m
Taiwan 145000556 *
• Longwell LP-71+VCTF+LS-33 1m
Japan 145000555 *
• Longwell LP-54+VCTF+LS-18 1m
Africa 145000554 *
• Longwell LP-39+H03VV-F+LS-18 1m
CE 145000553 *
• Longwell LP-34A+H03VV-F+LS-18 1m
CCC 145000538 *
• Volex LSG-31+RVV300/300+LS-18 1m
Argentina 145000528 *
• Volex LP-24+H03VV-F+LS-18 1m
Danmark 145000534 *
• Volex LP-40+H03VV-F+LS-18 1m
Switzerland 145000524 *
• Volex LP-37+H03VV-F+LS-18 1m
Brazil 145000527 *
• Volex LP-46+H03VV-F+LS-18 1m
Israel 145000526 *
• Volex LP-41+H03VV-F+LS-18 1m
UL 145000537 *
• Volex LP-30B+SPT-2 18AWG+LS-18 1m
UK 145000605 *
• Volex LP-61L+H03VV-F+LS-18 1m
Indian 145000536 *
• Volex LP-67+BIS+LS-18 1m
Italy 145000535 *
• Volex LP-22+H03VV-F+LS-18 1m

96
 Lenovo Y470/Y570

Table 11. Parts list—3-pin power cords (continued)

Region P/N CRU ID

Korea 145000533 *
• Volex LP-486+KTLH03VV-F+LS-5 1m
Australia 145000532 *
• Volex LP-23A+LFC-3R+LS-18 1m
Taiwan 145000531 *
• Volex LP-71+VCTF+LS-33 1m
Japan 145000530 *
• Volex LP-54+VCTF+LS-18 1m
CE 145000525 *
• Volex LP-34A+H03VV-F+LS-18 1m

97
 Lenovo Y470/Y570 Hardware Maintenance Manual

Notices
Lenovo may not offer the products, services, or features discussed in this
document in all countries. Consult your local Lenovo representative for
information on the products and services currently available in your area. Any
reference to a Lenovo product, program, or service is not intended to state or
imply that only that Lenovo product, program, or service may be used. Any
functionally equivalent product, program, or service that does not infringe any
Lenovo intellectual property right may be used instead. However, it is the user’s
responsibility to evaluate and verify the operation of any other product,
program, or service.
Lenovo may have patents or pending patent applications covering subject
matter described in this document. The furnishing of this document does not
give you any license to these patents.

LENOVO GROUP LTD. PROVIDES THIS PUBLICATION “AS IS” WITHOUT

WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON-
INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. Some jurisdictions do not allow disclaimer of express or implied
warranties in certain transactions, therefore, this statement may not apply to
you.
This information could include technical inaccuracies or typographical errors.
Changes are periodically made to the information herein; these changes will be
incorporated in new editions of the publication. Lenovo may make
improvements and/or changes in the product(s) and/or the program(s)
described in this publication at any time without notice.
The products described in this document are not intended for use in
implantation or other life support applications where malfunction may result in
injury or death to persons. The information contained in this document does not
affect or change Lenovo product specifications or warranties. Nothing in this
document shall operate as an express or implied license or indemnity under the
intellectual property rights of Lenovo or third parties. All information contained
in this document was obtained in specific environments and is presented as an
illustration. The result obtained in other operating environments may vary.
Lenovo may use or distribute any of the information you supply in any way it
believes appropriate without incurring any obligation to you.
Any references in this publication to non-Lenovo Web sites are provided for
convenience only and do not in any manner serve as an endorsement of those
Web sites. The materials at those Web sites are not part of the materials for this
Lenovo product, and use of those Web sites is at your own risk.

98
 Notices

Any performance data contained herein was determined in a controlled

environment. Therefore, the result obtained in other operating environments
may vary significantly. Some measurements may have been made on
development-level systems and there is no guarantee that these measurements
will be the same on generally available systems. Furthermore, some
measurements may have been estimated through extrapolation. Actual results
may vary. Users of this document should verify the applicable data for their
specific environment.

Trademarks

The following terms are either registered trademarks or trademarks of Lenovo in

the United States and/or other countries:
Lenovo®
Lenovo logo®
IdeaPad®
VeriFace®
OneKey Rescue® (OneKey Recovery, OneKey Antivirus)
APS®
Power Express®
Energy Management and ReadyComm®

The following terms are trademarks of Microsoft Corporation in the United

States, other countries, or both:
Windows®
Windows® 7

The following are trademarks of Intel Corporation or its subsidiaries in the

United States, other countries, or both:
Intel®
Intel®Core™ 2 Duo

Other company, product, or service names may be the trademarks or service

marks of others.

99