7.
Level 2 Repair
7-1. Components on the Rear Case
Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
7. Level 2 Repair
7-2. Pre-requisite
Tweezers / Disass'y Stick / Screw Driver Anti-static Gloves
Anti-static Mat Hot Plate
A OCTA Disassembly Holder OCTA Disassembly Upper
Ethyl Alcohol Cotton Swab
Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
7. Level 2 Repair
7-3. Parts which must be changed after repair
BOM A code Image Remarks
SVC BACK GLASS OUT
[GH81-14351A]
Replace for
Back Glass repair
SVC BACK GLASS IN
[GH81-14352A]
Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
7. Level 2 Repair
7-4. Disassembly
1 1) SOC 68% : Put the device in the chamber 2 Unscrew 12 Point and disassemble SIM Tray1,
for 10~20 minutes under 70℃. 2 from device
2) SOC 68% : Put the device in the chamber for
10~20 minutes under 60℃.
3) Detach the Back Glass.
※ Caution ※ Caution
1) Be care of scratch 1) Be care of scratch
3 Disassemble Upper Rear. 4 Finally Disassemble Rear of bottom side.
(Use disassemble hole left side of Rear to detach it) (Use disassemble hole left side of Rear to detach it)
※ Caution ※ Caution
1) Be care of Rear damage 1) Be care of Rear and connector damage
Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
7. Level 2 Repair
6 Detach Battery connect and the other
5 Unscrew PBA 3 points.
connectors. (7 Points, except for Front Camera
connector)
※ Caution ※ Caution
1) Be careful not to damage the PBA 1) Be care of connector/cable damage
7 Detach main PBA from Front. 8 Detach other components.
SUB Camera
Receiver Prox Sensor
MAIN Camera
Battery
Detach PBA
Motor
Ear Jack
※ Caution ※ Caution
1) Be care of PBA damage 1) Be care of several kinds of damage
Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
7. Level 2 Repair
7-5. Aassembly
1 Attach components on Front.
(RCV module, Sensor FPCB, Motor) and then 2 Attach PBA assy In Front Assy.
Press RCV. (PBA+ Front)
SUB
Receiv Prox
MAIN
Motor PCB 15°angle
Ear
※ Caution
※ Caution
1) Be care of FPCB damage and tilt
1) Be care of chip damage nearby screw point
2) Be care of press power/time
3 Attach Battery connect and the other 4 Screw PBA 3 points.
connectors. (7 Points) (Torque:1.2 Kgf·cm±7%)
Attach Front Camera on PBA.
※ Caution ※ Caution
1) Be care of connector damage. 1) Be careful not to damage the PBA
Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
7. Level 2 Repair
5 Assemble Rear of bottom side. 6 Assemble Upper Rear.
※ Caution ※ Caution
1) Be care of scratch and REAR damage 1) Be care of scratch and REAR damage
Screw 12 Point and Assemble SIM Tray1, 2 on
7 device 8 Attach Back Glass.
(Torque:1.3 Kgf·cm±7%)
※ Caution ※ Caution
1) Be care of chip damage nearby screw point. 1) Be care of scratch and tilt.
Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
7. Level 2 Repair
9 Press Back Glass.(1N for 1minute) 10 Do water resistance test(WRT)
※ Caution ※ Caution
1) Be care of scratch. 1) Be care of scratch.
11 If fail WRT doing debugging(sealing or etc) If connector problem, disassemble & remove
12 gasket
※ Caution ※ Caution
1) Be care of scratch. 1) Be care of PBA damage
Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
7. Level 2 Repair
13 Use O-ring(GzH81-14271A) on IF CON 14 ※ Remove USB Dispensing on PBA.
Reassemble & Re WRT Insert O-Ring on PBA.
※ Caution ※ Caution
1) Be care of scratch. 1) Be careful not to damage the PBA
Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
