An incomplete compendium of micrometers and their makers

© Peter Marks, 2011

Photos copyright their respective owners.

Table of Contents
What’s with all the micrometers? 4
The care & feeding of your micrometer 8

Almond Company 12 H&Hip 79

Ames 12 Hilger & Watts 80
Hommell Werke 80
Bailey 13 F. W. Horstmann Co. 81
BESTOOL-KANON 13
Betz 15 International Tool Co. 81
Boker 15
Brownie Tool 16 C. E. Johansson AB 82
Brown & Sons (Chicago) 50
Kalibr 83
Cadillac Gage Company 51 Keilpart 85
E.J. Cady & Co. 52 K. K. System 85
Robert W. Carson 52 Kukenis 86
Cary Le Locle 53 Kroeplin GmbH 86
Central Die Casting 53
Central Scientific Company 54 L.. 87
The Central Tool Company 54 Chas. Lowinson 88
James Chesterman & Co. 61 The Lufkin Rule Co. 89
Chicago Brand 61 LX 98

Davis & Thompson Co. 62 Mahr 99

Deltronic Corporation 62 C & E Marshall Co. 101
Ferdinand Durand 63 Louis Marx and Company 101
Massachusetts Tool Co. 102
E.D.A. 63 Massi 102
Elgin National Watch Co. 64 Mauser Werke 103
Etalon 64 MG 104
Millers Falls Co. 105
Federal Products Co. 68 Mitutoyo 107
Feinmess Suhl GambH 68 Montgomery Ward 114
Flechel & Brown 69 Moore & Wright 114
Fleming Machine Company 69 MTG, Inc. 116
Forsberg Mfg. Co. 71 Mueller Gages Co. 116
Fred V. Fowler Company 71 Muskegon Tool Industries, Inc. 117
W. Fox & Sons 73 MZB 117
Fulton 74
Nachi 117
Glastonbury Southern Gage 74 National 117
Goodell-Pratt 75 Neue Berliner Messingwerke 118
Greenfield Tap & Die (GTD) 77 Nippon Seisoku 118
NSK 118
HDT International 77
Helios Messtechnik GmbH & co. KG 78 Pacific Gage Co, Inc. 122
Henry L. Hanson 79 PAV 122
2
Pi Tape Corporation 123 Swiss Precision Industries 185
Pierre Roch S.A.R.L. 123 Syracuse Twist Drill Co. 186
BZG Polyplan 124 Tavannes Machine Co. S.A. 186
Lufkin / Pratt & Whitney 125
TESA 188
Rank Taylor Hobson Ltd. 126 Toyo Seiki Co. Ltd. 190
Reed & Prince Mfg. Co. 127 Triumph 190
Reed Small Tool Works 127 Tubular Micrometer Company (Tumico) 191
Regal Beloit, Inc. 129 Turner 194
Rimat Tool Co. 130
Union Tool Co. 194
Sawyer Tool Co. 130 Unknown makers 195
George Scherr Co. 130 The Van Keuren Co. 203
Scherr-Tumico Company 132
Louis Schopper 137 VIS/SPI/etc. 204
Schmutz Mfg. Co. 138
Scru Meter 139 Warszawa 204
Sears Roebuck and Co. 140 Welch 204
Seidensticker 144 Wells Brothers Company 205
Shardlow Micrometers, Ltd. 145 A.J. Wilkinson & Co. 205
J. T. Slocomb Co. 146 WJZ Gage & Tool Corp. 206
Sonoike Manufacturing Co. 153 Woodman Mfg. and Supply Co. 206
Sorensen Center-Mikes, Inc. 154
Standard 154 Carl Zeiss Jena 206
L. S. Starrett Co. 156 Zeus 208
Steinmeyer 181 Zim Manufacturing Co. 208
C. Stiefelmayer 183
Stoetling Co. 184 Miscellaneous items 208
Sunnen Products Co. 184
Supreme 184
Swedish Gage Co. 185

3
What’s with all the
micrometers?

One might reasonably ask why so many microm- attempted, failed, and successful competitive differ-
eters -- and why might I want to take one or more of entiation.
them home with me?
This history of a this iconic tool also illuminates the
The quick answer is that most any engineer, archi- manufacture of interchangeable parts; the great pat-
tect, or anyone with a pretense to understanding the ent sweepstakes of the late 1800’s (when inventors
physical world ought to have at least a 0-1” microm- rather than lawyers were driving the process); a
eter of good quality. And, ideally, provide them for surge in manufacturing with WWI; the subsequent
their kids, nieces, nephews, and anyone else they decline and mergers of companies during the Great
think ought to acquire some sort of mechanical lit- Depression; huge demand during World War II;
eracy. post-WWII industrialization; the eternal optimism
of entrepreneurs for more than a century; the trend
How can we appreciate nano without understand-
toward conglomerates; and the recent crush toward
ing .001” and .0001” and .00001” (or .01mm and
globalization.
.001mm) along the way?
There are also modest stories of company survival.
My collection began with various types needed for
For example, how one family company (the Central
accurate work in my home shop. It started with just
Tool Co.) survived for a hundred years, despite a
a 0-1” micrometer back during my college years.
middling product; how many manufacturing greats
Along the way, I started using some micrometers as
entered and then failed to survive in this business;
hands-on examples in seminars of how companies
and even how Sears Roebuck & Co. went from the
try to differentiate themselves from the competi-
greatest thing in sales and distribution to poor prod-
tion.
uct management, fuzzy thinking, and decline.
The micrometer is the iconic tool of the Industrial
Revolution. Although its form has remained es- Customer “$APPEALS” is an acronym that covers
sentially unchanged for 150 years (try that with the eight ways that people differentiate one product
your MP3 player) its design and manufacturing from another. Understanding how customers make
evolution punctuate a timeline of industry from the their buying decisions – and what might be done
mid 1800’s to today. to win more of those decisions – is a key to effec-
tive product development, manufacturing, distribu-
Want to see what the Great Depression and Great tion, marketing, and sales. Most any product can
Recession have in common? It shows up in the his- be used to illustrate the principles; but few products
tory (and consolidation) of micrometer makers. have the 150 year history of the micrometer to draw
from in providing lessons.
Wonder how Germany, England, Japan, Russia, and
the U.S. geared up to fight World War II? And how The $ in $APPEALS reflects price differentia-
they fared thereafter? It’s reflected there as well. tion. It ranges from a signal of quality and prestige
(high price) to a strategy to win good-enough-for-
Customer $APPEALS me buyers (low price). Competition. A hundred
manufacturers have entered – and many exited – the
market. Some tried to compete solely on low price.
Some of you may know of my “$APPEALS” ru-
bric; based on research into how we humans choose Others have aimed to produce all-in-one measur-
what product or service to buy. The 150 year his- ing products – with fewer tools needed. The “in-
tory of the micrometer provides scores of cases of terchangeable anvil” micrometer is one example
4
that aims to retain quality, with fewer micrometers signed – my Art Deco micrometer from Louis
needed, but at the cost of convenience. Schopper (Leipzig) is an example. Still others have
fancy logos, cool cases, elaborate in-store displays,
For decades there has been a pattern of newly indus- and the like.
trializing countries entering our market with lower
priced tools. We’ve seen this with Japan, Poland, Companies like Brown & Sharpe also experimented
and most recently China as examples. Years ago, with modern adornments – almost the automotive
2:1 price differences were common. Today 10:1 tail fin equivalent of protective plastic pads and the
differences are common. Indeed, vast disparities in like.
production costs have recently pushed many quality
manufacturers out of the precision hand tools busi- The second P in Customer $APPEALS is for Per-
ness – or to have their branded tools made in China formance. While emotion is a key to any buying
-- as they migrate to higher margin products (coor- decision, the rational decision is dominated by price
dinate measuring machines and the like). and performance – how well does the product do
its intended job? In this case, the question is how
The A in $APPEALS stands for Availability. quickly and accurately can a user make a measure-
Many of the competitive battles in any market are ment?
based on distribution: getting customers what they
want, when and where they want it. At least a score There have been hundreds of micrometer patents
of companies have entered the micrometer business aimed at getting a competitive edge in one way or
with excellent products, but failed to get widespread another. Performance issues might be divided into
distribution. Still others managed to find a niche. three broad categories.
For example, most large industrialized countries The first includes the introduction of various types
have a top two or so national suppliers. In the US to make different measures. We have outside, inside,
this would be Starrett and Brown & Sharpe, who height, depth, thread, gear, tubing, groove, bore, etc.
battled each other for more than a century. micrometers. There are easily two dozen types to
Other suppliers found niches. For example, Scherr- measure the tiniest watch parts to hot steel coming
Tumico sought government sales and Central Tool off a rolling mill. We’ve also added new function-
concentrated on automotive service markets. Oth- ality in the electronic age, such as instant English/
ers concentrate of watchmaking and jewelry trades. metric units conversions and automated acquisition
We also find companies making micrometers for of readings for statistical process control.
sales through various branded channels (many dif- The second category includes improvements aimed
ferent suppliers for Sears/Craftsman, Slocomb for at higher accuracy within a type. The principle of
Snap-On, Central Tool for lab suppliers like Welch the micrometer is based on manufacturing a pre-
and so on). cision screw – of exact and unvarying pitch -- and
Pure distributors have also held sway; such as the mating it to a nut (actually an entire frame) of equal
Scherr component of Scherr-Tumico, Fowler, and accuracy. Users must typically rely upon brand
SPI – “Swiss Precision Instruments” – which is now reputation and their own calibration labs to judge
more likely to import cheap Chinese tools as any- this.
thing either Swiss or particularly precise. Another issue in accuracy is carefully control-
ling the pressure generated between the anvils as
The first P in Customer $APPEALS is for Packag-
the screw thread is tightened. Slight differences in
ing. It refers to the visual differences between prod-
torque/pressure can easily change the measurement
ucts; everything from the product itself, to its boxes,
and even damage the tool or part. For this reason,
the look of the stores that sell it, and so on.
a large variety of friction thimbles, ratchets, spring
Micrometer makers have tried a variety of tweaks to pressure gages, and the like have been developed.
differentiate their products. Some have chromed Van Keuren even made a “light wave micrometer”
finishes and others paint. Some are elegantly de- that used optical fringes to judge and control pres-
5
sure. Such features as carefully hardened and ground
screws, hardened or carbide anvils, and special nut
A third and final performance measure is capacity. designs to take up wear can greatly extend the ac-
Outside micrometers commonly come in sets of six curate working life. Almost all quality microme-
from one to six inches in capacity. Larger sizes, to ters have some sort of adjustment to take up wear
two or three feet diameters, are commonly available. in the spindle – often a sort of split and adjustable
The largest capacity precision gage in this collection nut. Cheap micrometers lack this. As just one ex-
(not really a micrometer) is a Pi tape that reads up ample, dating back to the late 1800’s, Slocomb de-
to 8’ in diameter to .001 inches. signed a unique two-part nut with a spring in be-
The E in Customer $APPEALS is for Ease of use tween. These kept their micrometers in adjustment
refers to all the other sensory inputs a customer/ for many years – and also contributed to long life.
user will use to differentiate between products. A company’s own network of sales, service, and sup-
Ease translates to easier and faster measurement; port is also part of “assurances.”
and sometimes a delight in use. Among the ways
manufacturers have attempted to gain an edge: The L in Customer $APPEALS is for Life cycle
costs include all the costs a customer may incur af-
Easier reading through better verniers, larger thim- ter the original purchase. For more complex prod-
bles and graduations, mechanical digital and then ucts, these may be many times the purchase cost.
electronic digital readouts. Some amazing me-
chanical digital micrometers have been produced One of the reasons the product architecture of mi-
over the years. crometers has changed so little, is that it has proven
durable. Early electronic micrometers, while less
Faster use through “speeders” or sliders that allow durable, still had at their heart a precision screw
near instant adjustment to size. Etalon also pio- mechanism. So, the biggest unanticipated cost of
neered a “Micro Rapid” thread that advanced and micrometer use is errors in measurement. These
retracted four times as fast as a conventional mi- can cause scrapped parts, field failures, and the like.
crometer, with no loss of accuracy.
Manufacturers have provided a variety of means to
The elusive “feel” that quite correctly inspires a help assure accuracy. Some concentrate on ease of
sense of confidence as a micrometer thimble spins reading by less experienced users. Others include
smoothly – neither too loose nor too tight and nev- tools and services for easier calibration and repair.
er a hitch – down to a firm close. As just an ex- Most micrometers larger than 0-1”, for example, will
ample, some early Chinese micrometers cloned the have come with a “standard” to check their use.
look of makes like Etalon and Mitutoyo. But when
the anvils were closed there was a sort of squishy And finally, the S in Customer $APPEALS is
feel – indicating lack of parallelism in the faces and for Social Sanctions (and Standards) includes all
backlash in the screw/nut of the cheaper units. the people, opinions, experts, regulations, and the
like that influence the buying decision. There are
Ergonomic design, with dimensions to better fit the
standards (ISO, DIN, JIS . . .) , for example, for mi-
hands.
crometer accuracy. Most important, though, has
Lightweight design, especially in larger sizes. For been brand reputation. One of the interesting as-
example, the Tubular Micrometer Co. (Tumico) pi- pects of human decision-making is that we like to
oneered a hollow vacuum sealed frame, for example. keep things simple. This often means that we have
a fairly limited consideration set –the best known
The A in Customer $APPEALS is for Assurances and best distributed brands get the lion’s share of the
refers to customers’ fears of what might go wrong business. This often translates to a top two or so
and how the manufacturer goes about allaying these (think Coke and Pepsi, followed by Dr. Pepper) in
fears. For micrometers, one issue is long term reli- many industries.
ability. Will the micrometer stay in calibration?
In some cases, brand reputation may be higher or
6
lower than might be warranted by actual prod- pears on union pins, tie tacks, logos, and more. It’s
uct quality. While opinions will vary, Starrett is sometimes a give-away gift for valued customers
a company with a great reputation which makes a (e.g. promotional micrometers) and an award for
wide range of very good, but not stellar products. achievement (e.g. the Chrysler Master Technician
Scherr-Tumico is a company that made many equal- Award micrometer included in this collection).
ly good micrometers to Starrett, but with a fraction
of the brand loyalty. The steps companies made to Here, as another example, is a Masonic presentation
increase or limit their brand equity are often illus- micrometer from Great Britain:
trated.

Exploring product differentiation

Anyhow, I ended up gradually acquiring examples

of micrometers just to make a point about product
differentiation. For example, the US or European
version and its Chinese clone. Or, examples of how
Starrett and Browne and Sharpe battled each other
over features and patents.
I also acquired multiple examples of some clas-
sic micrometers just to give away to kids. They’d
measure and compare the thickness of their hair.
“Count” a stack of paper by measuring the thick- This iconic status may also explain why so many
ness of a few, and then the thickness of a stack. And machine tool manufacturers at one point decided
so on. Here and there these young folks went on to to enter the business of making micrometers (hey,
become architects, engineers, guitar makers, or sci- that’s cool, our very own micrometers) only to later
entists – though probably due only in the slightest find it was easier to make good tools than to make
to my interest in their interests. a profit.
It also became clear, the more I learned, that the Still later, it seemed like I might eventually write a
precision screw thread was, perhaps, the seminal Connections-like history of this (liberally illustrat-
invention (apart from steel making) of the indus- ed with examples) sometime when I was 80 years or
trial age. Without it we wouldn’t have machine tool so old and bored. Each manufacturer has a com-
feeds and threads. We wouldn’t know how to make petitive story. Hundreds of designers tried to find
gears. The basis of precision manufacturing and in- a way to however subtly differentiate their product.
terchangeable parts would be lost. Even the step- One can even construct a sort of timeline, marked
per systems behind semiconductor masks wouldn’t with the introduction of various micrometer exam-
be possible. So, there’s a sort of “Connections” (re- ples and how they mirror the economy, culture, and
member James Burke?) story here. At some point politics of their times.
we may look back fondly on the period from the late
1800’s through the 1900’s and consider the microm- All of which is to say that I now have a **** load of
eter one of its key artifacts. It turns out that most micrometers and allied precision tools, many pretty
anyone can carry a 100-year-old exemplar of the cool (at least to me), and not much time to use them
dawn of the Industrial Revolution (an 1880’s mi- myself, give them away to kids, use them as product
crometer) in their pocket. Try that with a Bessemer differentiation examples, or write the book.
converter . . .
So, the idea is that everyone with any pretense to
The micrometer is the iconic tool of the machine technical sense needs at least one or two microm-
tool industry, machinists, and toolmakers. It ap- eters. 100% of your donation will go to a scholar-
7
ship fund, with Brad Holtz, David Ullman, and oth- • calibration
ers deciding who gets the nod. The prices are set • steel versus carbide anvils
reasonably. Chances are you won’t find the same • refurbishing spindles and anvils
• micrometer locks
type and condition of tool much cheaper elsewhere. • storage
In a few cases the tools are rare enough you may • what influences prices
never find another one. • cosmetic defects and repairs
• micrometer stands
Everyone needs at least a 0-1” micrometer (a.k.a. • which ones to buy
“mic” or “mike”). Your curious children, neighbor • notes about condition
kids, nieces and nephews will also benefit from the
gift of a micrometer and an afternoon spent mea- Restoring your mic
suring everything in sight. There are some excel-
lent micrometers here for $25 and under – buy a Some of these tools may have been sitting for de-
bunch for your First Robotics crew! There is even a cades, with congealed oil. In other cases they
“six pack” listed here. have been sprayed (by me) with a light coating of
Boeshield – a waxy rust inhibitor suited for preci-
If you’re more than slightly mechanical, you might sion tools. A smooth feel can often be restored by
find good use in a larger set. If you know lots of just opening and closing (gently) the micrometer a
kids, you might walk away with several of the still- few times.
iconic-but-less-expensive mics.
In almost all other cases it can be restored by un-
Some of these instruments are just so cool, they be- screwing the thimble, washing the threads inside
long on your desk. Get the inclinometer to tell if and out with a solvent (lighter fluid, lacquer thin-
your colleagues are on the level. Keep a huge mi- ner, etc.) and working a drop of pure light oil (Star-
crometer to size up the situation at hand. Have a rett, 3-in-1, any pure10 weight oil) into the threads.
height gage to show your aspirations. Don’t use WD-40 -- it leaves a gummy residue.
You might also express your heritage or compare Don’t attempt to disassemble an analog Slocomb
design cultures. There are American, Brazilian, mic or a mechanical or electrical digital mic un-
Chinese, English, French, German, Italian, Japa- less you know what you’re doing. The old Slocomb
nese, Polish, Russian, Swedish, and Swiss mics here. mics have a cool self-adjusting nut (two halves, with
Some, even, from Lichtenstein. aligning teeth, and a spring in between. Many of
My hope is that those of you at COFES will have these end up with one half stuck in the back of the
some fun with this; that most of you will end up with thimble from inexperienced folks disassembling
a great deal on one or more cool tools; that some them. This can be fixed, but only by making a tool
you give one or more away to spur a younger per- from brass tubing. Mechanical and electronic digi-
son’s interest in technology; and that we’ll all help tal mics can lose their registration if disassembled.
a high potential student deal with the sometimes- As a side note, you may wish to remove labels on
insurmountable costs of college. the boxes or cleanup dirty and marked cases. Start
with a citrus based cleaner such as Goo Gone or
The care & feeding of your Goof Off. Let it soak in and then remove the label,
dirt, or markings. The spindle wear nut (common
micrometer to most better analog mics) may also have to be ad-
This covers: justed for free play.

• tight spindles
• disassembly of analog mics Adjusting your mic
• carefully removing labels
• spindle wear adjustment Before attempting to adjust a micrometer (to zero
• micrometer adjustment
with a 1” mic or with a precise “standard” on a
8
larger mics), be sure the anvils and standards are threaded spindle from the thimble. It’s often a ta-
completely clean. It is common for micrometers pered fit, retained by a screw at the end of the thim-
to read about .001 high, just due to residue on the ble.
anvils. A 1” mic can be cleaned by lightly screwing
down on a piece of paper (with cotton rag content, Cheap micrometers come with somewhat soft steel
not polished/smooth clay content) and gently pull- anvils, which may or may not be flat and parallel.
ing it out. Good micrometers may come with harder anvils (ei-
ther tool steel or carbide) that are built and checked
Once the anvils are clean you can check and adjust for flatness and parallelism. These checks are
for accuracy at the low end (zero or small standard) made with optical flats and parallels, placed under
size. Minor adjustments are commonly made a monochromatic light, with the optical fringes read
(most Starrett, B&S, Mitutoyo etc.) by ever so slight- to check flatness and parallelism. The gage block
ly turning the barrel with the fixed indications using sets noted above can also check for out-of-parallel
a tiny pin spanner wrench. Scherr-Tumico mics lo- anvils by checking at different rotation points.
cate the adjustment barrel/spanner on the thimble.
Steel anvils are fine for ordinary use. Carbide anvils
Some of the micrometers here may not have their will last longer in frequent use and abrasive envi-
original adjustment spanners included. I’ve sent ronments. However, they are also subject to chip-
along s a box with a hundred or so replacements. ping (which is common when large mics are used
Find one that fits your mic if needed. The pin or for checking work on a lathe).
hook end should fit the appropriate barrel or thim-
ble. The other end may be a spanner for the spindle Worn steel anvils on a top quality mic can refur-
wear adjustment nut. These are also available at low bished by lapping them back to calibration (this was
cost from most industrial suppliers. typically done with a Van Keuren micrometer lap-
ping kit). Chipped carbide anvils can be replaced
The screw thread on a good micrometer will be of and lapped. Either step is only worth doing for the
such high quality (and so resistant to wear) that a very best micrometers. Unless you have the equip-
mic that is adjusted properly at one point will be in ment, send it to someone like the Long Island Indi-
calibration at every other point. In practice, threads cator Co.
wander and there is backlash and wear. Different
grades of micrometer will also have rolled threads
Micrometer locks
(not so accurate) and lathe cut or ground threads
(potentially very accurate). Grinding also allows
the use of hardened and thus more wear resistant Many of these mics will have a micrometer lock.
steels. These are usually pretty easy to figure out; though
care in orientation may be needed if you disassem-
If utmost accuracy is needed, micrometers are ble and then attempt to reassemble your microm-
checked with a special series of gage blocks that eter. Be aware that some Starrett and other mics
test the thread at different sizes and rotations of the with a round knurled lock have a sort of tiny cam
spindle. Checking at different rotations also checks and roller mechanism. Take care if you disassemble
for parallelism of the anvils. For your purposes, if this not to lose the tiny roller.
you have a good mic and want .0001 accuracy, then
adjust it using a standard very near the size you will
Storing your mic
be measuring.
Some older mics make the adjustment at the junc- Micrometers should be put away with a gap between
tion of the frame and anvil. Interchangeable anvil the anvils. First, any trapped humidity can result
mics have adjusting nuts on the various spindles. in corrosion. Second, you don’t want to take the
chance someone will turn down hard on the anvils
Major adjustments, which should rarely if ever be
and distort the frame. If you’re concerned about
needed, are commonly made by disassembling the
9
rust and long term storage, Boeshield spray can help I’m one of the few foolish enough to be interested for
protect your tools. It leaves a thin waxy finish that all three of the above reasons; as well as the some-
is easily wiped free with a light oil when you need times brilliant and sometimes horribly misguided
to use the tool. In general, precision tools are best attempts of companies at product differentiation
stored below 55% relative humidity, which provides over the decades.
a safety margin for condensation and is usually low
enough to inhibit mold formation on cases and the Many perfectly functioning micrometers may
like. come with cosmetic defects. For example, most
large companies have a calibration program which
requires that each precision measuring tool be
What makes a micrometer more or less ex- marked or engraved in some way for traceability
pensive? and annual calibration. In other cases there may
be wear to painted surfaces, light surface rust, and
There are at least three main reasons why buyers the like. Many of these cosmetic defects can be re-
will spend more or less. paired. Light surface rust to knurled parts can of-
ten be removed with a fine brass wire wheel. Light
First and foremost is the utility, accuracy, and re- rust to smooth surfaces can be removed by using
liability of the micrometer. Even with standard very fine silicon carbide sandpaper (e.g. 600-900
outside micrometers, new versions may range from grit) and oil. Be sure to remove every bit of grit
about $10 (lower cost Chinese imports) to $350 and don’t touch the measuring surfaces. Painted
(for example, high quality Swiss-made micrometers frames can be repainted. Wrinkle and hammertone
with great attention to detail). In addition, designs finish paints (both common in micrometer frames)
for special purposes will tend to be expensive – of- are also available in spray cans.
ten as much as $400 (e.g. good V-anvil micrometer)
to over $1000 (e.g. a well made bore micrometer or Note that in some cases, such as with very old and
very large sizes). The Cary Le Locle bench microm- rare instruments in basically good condition, such
eter in this collection was originally around $3000. restorations may affect value. In any case, rough
methods such as sand blasting and heavy wire
Second is the collector market, based on the rarity wheels should be avoided.
of the micrometer. Age and condition, the inclu-
sion of old patent dates, and the like are factors in A variety of micrometer stands have been made
this. There are also collectors for small microm- over the years, to clamp micrometer frames in a
eters (e.g. ½” capacity); and not so many for large somewhat upright position. These have the advan-
micrometers. Collectors have paid $2000 or more tages of leaving one hand free and also reducing the
for some rare micrometers; with many in the $500 thermal effects of direct handling. The Mitutoyo
range. type of stand and its clones are probably dominant
today; and a few examples will be in the group for
Third, is a variety of special intrigues affecting price. donation. These are recommended, also, for a cool
Mauser gun collectors like Mauser micrometers. micrometer that might benefit from a stand. Get
Optical collectors like Zeiss micrometers. Others a large micrometer and stand – and hold down the
will judge by country of origin, favorite brands, re- fort.
ally cool mechanical features, and the like. Given
the dozens of manufacturing companies that have
entered and exited the micrometer market, some Picking a micromenter
are bought because of a past connection to the com-
pany. In some cases there will be both really cool So, which ones should you buy? Remember, your
features and rarity; such as some early mechanical donation is doing at least triple duty. First, the pro-
digital micrometers, the Polyplan 0-4” set, or the ceeds go to a engineering / technical student with
Van Keuren Light Wave Micrometer in this collec- both a bright future and a need for help. Second, if
tion. you give what you acquire to another aspiring stu-
10
dent, you (and the stories and experiences that go feels good in your hand. Some folks like the feel
along with it) will get a second chance to nudge the of a micrometer with a light frame and a smaller
world to a slightly better orbit. Third, in many cases thimble (for example, the widely sold Starrett #436
these have been set at bargain prices. Newer ones series). Others (myself included) prefer a larger
are often at a fraction of new price. Older and rarer and easier to read thimble.
ones are often at significantly less than final auction
prices for equal examples.
Some notes about condition
To me, this best micrometer to give away to an as-
piring engineer or scientist is one that has a bit of a Finally, some notes about condition. These mi-
story, that retains its accuracy, that doesn’t cost a crometers were packed up in early August, 2011 and
fortune, and inspires some pride of ownership. then spirited away to a storage locker in Arizona.
Hopefully, they will remain in as-packed condition
Often, I’ve acquired several instances of microm-
(within original cases if present, plastic bags etc.)
eters that seemed (to me) to fit the bill. If you’re
over the next few months. Seems unlikely they’ll
overwhelmed by choices, let me suggest one of these
get too much humidity in Arizona. Anyhow, if a
models:
condition is listed, it’s my quick, subjective take at
• Starrett #232 0-1/2” micrometers. These tiny the time of packing. You should inspect these for
micrometers fit anywhere, work well for their yourself.
size, and make a good gift.
Micrometers listed as near new or near mint will
• B&S #1 micrometers with fixed-friction
thimbles; either US (ideally before 1980) look new from a distance, but might have faint rubs
or Swiss made. Choose a recent (last four to the paint or chrome. Excellent won’t be far be-
decades) micrometer with good ergonomics hind. Very good condition should function well but
and accuracy. have more signs of use. Generally, non-original
• B&S #15 micrometers with an 1884 patent markings will be noted – and you wouldn’t expect
date. These offer a bit of history in a simple to find them on a near new or mint condition mi-
and robust design that’s still likely to be use- crometer unless they’re specifically noted.
ful.
Age wlll also be a factor – a century old micrometer
• B&S #233RS bench micrometers. Call me won’t be expected to be spotless and such things as
crazy, but these would look nice on your
desk. ratchets and locks may be worn.

• Goodell-Pratt / Millers falls micrometers There aren’t many poor condition mics included
with the small speeder and thimble mounted here (with the exception of a box of 25 examples
ratchet. Good ergonomics in a WWII era in mostly working, but poor cosmetic condition. A
tool. few are included due to their age or rarity. Note
• Recent Lufkin/Pratt & Whitney micrometers also that a micrometer may still be quite accept-
with the larger thimbles. able for use, while having markings, stains, etc. that
• Mitutoyo non-rotating spindle micrometers wouldn’t delight a collector.
(#106-102). Indeed, most Mitutoyo microm- Prices are low enough in many cases that you can be
eters are pretty good.
the first kid on your block with some rare instances
• A early Slocomb micrometer in good condi- . . . and still afford a handful of interesting examples
tion. for all the other kids on the block or in your extend-
There is a large variety of other great makers to con- ed family.
sider – many of superior quality (and cost) -- as de- The collection includes examples from a bit more
scribed in the following pages. than 120 makers and distributors, as well as exam-
One of the important steps is to find a model that ples of tools from other than micrometer makers to
round out the story on precision measuring.
11
Almond Company
The company began in Brooklyn, NY but was moved to Ashburnham, Mass in 1912. Manufacturing of
micrometers ceased in 1930, perhaps due in part to both competition and the depressed economy of the
time.
Item #001
Almond Co. 0-1” micrometer marked No. 140.
Decimal equivalents on the frame. This is marked
Ashburnham, Mass. Good condition

$35 donation

Item #002
Almond Co. 0-1 and 1-2” micrometers with
straight knurled thimbles.
The 0-1” is .0001 reading and has a ratchet. Collect-
ible, dating from 1912-1930. And given the name, us-
able as both micrometers and nut crackers.

$55 donation

Item #003
Almond Co. 0-1 and 2-3” micrometers with tra-
ditional diagonal knurled thimbles.
The 0-1” is .0001 reading. Collectible, dating from
1921-1930.

$55 donation

Ames
B. C. Ames (Waltham, Mass) was founded by Bliss Charles Ames (cool name) in 1896. Early maker of
dial gage heads and still a maker of dial gages.
Ames was the maker of the unique “Scru Meter” indicator and likely the entire patent-applied-for thread
gage noted in its own listing.

12
Bailey
W.H. Bailey & Son, Ltd. (London) was incorporated in 1906. To the best of my knowledge this provider
of medical supplies ceased operation around 1970.

Item #004
W.H. Bailey & Son head and neck (or medical /
forensic) calipers.
These read directly in parts of an inch. This set of cali-
pers has been thrown in just to measure outsize intelli-
gence of those at COFES. Brad will demonstrate; hav-
ing volunteered to earn his certification in phrenology.

$30 donation

BESTOOL-KANON
BESTOOL-KANON (Japan) was established as the Kanon caliper laboratory in 1938 and changed its
name to Nakamura Mfg. Co in 1943. Since then it has made such products as torque wrenches, CMMs,
and digital calipers. It’s a relatively small company; under 100 employees. It isn’t clear if they made their
own micrometers or were supplied by another manufacturer. However, the designs are subtly different
than the usual NSK and Mitutoyo examples.
Item #005
BESTOOL-KANON 0-1” micrometer with satin
chromed frame, plastic thermal pads, ratchet,
lock, and .0001” vernier.
Marked “PAT. PEND” on reverse side pad, but of such
conventional design it’s hard to see why a patent might
be granted. This example is in good working condi-
tion but has engraved QC numbers.

$15 donation

13
Item #006
BESTOOL-KANON 0-1” micrometer with blue
hammer paint frame, plastic thermal pads,
ratchet, lock, and .0001” vernier.
Likely of later manufacture than the previous example;
with straight line knurling of the thimble.

$20 donation

Item #007
“PII” micrometer 0-1” with basically identical
construction to the blue hammer paint Kanon
example.
Includes the same ratchet, the same straight knurled
thimble, the same lock, the same 0001” vernier and the
same paint. Minor differences in the rounded opening
frame and pads, which now include decimal equiva-
lents. Almost surely from the same factory. The “PII”
may be for “Phase II” – which is a US distributor (man-
ufacturer?) founded in 1981. Phase II now sells mostly
Chinese-made tools into the US; though Mexico and
Venezuela are also listed among their locations. If so,
this micrometer would date from a time when Japan
was considered a lower cost producer; probably about
25-30 years ago. Very good condition.

$25 donation

14
Item #008
“SPI” micrometer 0-1” with identical thimble,
ratchet, and lock construction to the PII and
later BESTOOL-KANON examples.
The frame is a “modern” angular design in satin chrome
with a painted plate with decimal equivalents attached.
SPI stands for “Swiss Precision Industries” – once an
importer and distributor of some Swiss tools and in-
creasingly an importer of lower cost tools. This tool
likely dates from a time when Japan was considered
a lower cost producer; perhaps the 70’s or early 80’s.
Tool is marked with a small inscription “PMW18.
Note also a Scherr-Tumico labeled micrometer other-
wise identical to the SPI micrometer above.

$25 donation

Betz
Item #009
Betz head and neck calipers.

$20 donation

Boker
Item #010
Boker 0-10mm micrometer.
Nicely made with an old-style anvil adjustment. My
assumption is that this is from Boker (Boeker), a Ger-
man maker of hand tools. The company traces its roots
back to the 17th century. Today the Boker company is
best known for its knives. This looks to be a microm-
eter made after WWII.

$25 donation

15
Brownie Tool
Brownie Tool Co. (Minooka, Illinois). The small-town company is pretty much a mystery. The company
went to the trouble to have the BROWNIE name forged into a variety of frame sizes. It also made a fairly
complex set – with an inside mic plus 0-4” outside mics in a fitted tray. However the overall execution
lacks finesse. Then, there’s the Brownie name. An attempt to be Brown & Sharpe’s kid brother? Named
“Brownie” for the fudge factor in execution? This is your very own mystery to take up with the History
Channel in a visit to Minooka?
One of the cautions about using a micrometer is that it shouldn’t be tightened as if it were a C-clamp.
However, I’ve also seen an example of a C-clamp with what appears to be the same “Brownie” name cast
(forged??) into its frame.
This may explain some of the slightly perverse design sense behind these micrometers.
Item #011
Brownie 0-1” micrometer in original case.
The History Channel artifact!
$20 donation

Item #012
Brownie 0-1” micrometer

$12 donation

Item #013
Brownie 0-1” micrometer with no case.

$10 donation

16
Item #014
Brownie 0-4” outside mic set plus and inside mic
set in the bottom half of a fitted case.
The largest size micrometer is a bit clever; perhaps the
only interchangeable spindle micrometer ever made?
Every other maker changes the anvils. This instead has
two spindles. One for the 2-3” size and one for the 3-4”
size. Calibration is through a screw set into the end of
the thimble. Also included is an inside micrometer of
somewhat clumsy design. The entire set is likely rare,
though not in the sense of rarified. These do work, but
are likely better suited as warnings about entrepreneur-
ship.

$50 donation

17
Brown & Sharpe
Brown & Sharpe (Providence, RI) began as D. equivalents stamped on the frame cost about $120,
Brown & Son in 1833. After his father left the busi- while the simpler frame design of the REX models
ness in 1841, Joseph R. Brown operated under his was equivalent to about $75. The REX design with
own name. By 1850 he had created a linear dividing a square throat frame (compared to a semi-circu-
engine, the first of its kind, and began making and lar throat) had the advantage of reaching deeper to
selling precision machinists’ rules. something like 1” plate.
Lucian Sharpe began as Brown’s apprentice and, in The B&S plant grew from 6.5 acres of floor space
1853, became a partner as the company was named in 1896 to nearly 32 acres in 1925. Throughout it’s
J.R. Brown & Sharpe. In 1868, the company was many years B&S was an innovator in both machine
reorganized as Brown & Sharpe Mfg. Co. tools and precision measuring tools. During World
War II it had 11,000 employees.
A year earlier (1867) Joseph Brown and Lucian
Sharpe attended the Paris Exposition and saw a As with most suppliers, World War II was a time of
Palmer micrometer, arguably the world’s first. They both increased output and material shortages. A
developed an improved version in 1868. February 1, 1943 booklet lists hundreds of product
numbers as “Items Temporarily Withdrawn from
An example of their improved design – an 1878 pat- the No. 34 Small Tools Catalog and the #142 Gener-
ent sheet metal gauge – is included in the collection. al Catalog.” This included a long litany of microm-
A January 22, 1884 patent covered an improved eters; and all those with tungsten carbide measuring
method of taking up wear between the spindle and surfaces.
“nut” – and several micrometers in the collection Henry Dexter Sharpe was Chairman in 1949, with
include this patent date. By the mid 1880’s the Henry D. Sharpe, Jr. taking the position of presi-
Brown & Sharpe micrometer acquired a form that’s dent in 1951 and Chairman in 1996. In 1964, B&S
basically familiar today. moved its operations from Providence to North
A November 6, 1894 patent indicates a B&S ratchet Kingston, RI.
stop. Brown & Sharpe partnered with and then acquired
The December 30, 1902 patent covers a method of the Swiss firm TESA in 1967, while keeping the
spindle locking using a knurled roll with a sort of TESA brand active. Many of their Swiss-made mi-
cam lock surrounding the spindle. Earlier designs crometers will have both B&S and TESA versions,
often used a much less convenient front-side lock- differing only in the branding.
ing nut, compressing a split collet that protruded By 1980 there was less emphasis on machine tools
into the open frame area. Later designs used a lock- and more on metrology. During much of it’s long
ing lever, with a sort of cam form built into it. life B&S battled Starrett as the leading US makers
Brown & Sharpe were also keen promoters of the of precision tools.
apprenticeship system. A number of excellent engi- The company unionized after WWII; and a 1981
neers and managers were developed over the years; strike decades later proved costly. Management
and even after the deaths of the founders (J. R. (Dan Roach was president at this point) wanted to
Brown in 1876 and Lucian Sharpe in 1899). Fam- continue a no-layoffs policy, but with much greater
ily members participated in company management flexibility.
over the next many decades.
Sixteen hundred machinists, worried about the
B&S was early to recognize the need for both pre- privileges of seniority, walked off their jobs in what
mium and economy levels of tools and in 1915 in- became the nation’s longest lasting and one of its
troduced its “REX” micrometers. In today’s dol- most contentious strikes. The strike officially ended
lars, their polished steel micrometers with decimal
18
in 1998, with B&S winning a Pyrrhic court victory. is as well or better known for coordinate measur-
My guess, based only on having a front row seat to ing machines as its legacy of hand measuring tools.
the UAW and Ford in the 1970’s is that there was Hexagon moved B&S operations to Connecticut
plenty of blame to go around. In any case, most of in 2005; and employment in Rhode Island is down
the more recent B&S micrometers in this collection from about to 11,000 at its high to essentially zero.
were made in the 1960’s or 1970’s or in the Swiss
TESA plant. One source of a more complete history is: http://
www.fundinguniverse.com/company-histories/
In 2001 Brown & Sharpe (and with it, TESA) were Brown-amp;-Sharpe-Manufacturing-Co-Compa-
acquired by the Hexagon Metrology division of ny-History.html
Hexagon AB. Today, the Brown & Sharpe brand

Item #015
Brown & Sharpe April 23, 1878 patent pocket
sheet metal gauge.
Brown & Sharpe credits itself with inventing the
world’s first practical micrometer – and this is an early
example. As to who developed the “first” microm-
eter in commercial production, the French “Palmer”
micrometer of 1848 usually gets that credit. Interest-
ingly, it was called the “Palmer screw” in Spanish, quite
rightly emphasizing the role of precision screw making
in its manufacture. Years earlier (1805) the mechani-
cal genius Henry Maudslay created a single microm-
eter capable of reading .0001 as the arbiter of accuracy
in his own shop. Still earlier, (1639) a precision screw
was used by William Gascoigne for astronomical mea-
suring purposes.
B&S started making their version, a sheet metal gauge,
in 1867. Notable features include the split-frame and
tightening bolt to take up wear on the screw, and the
anvil adjustment to adjust and take up wear on the an-
vil.
$?? donation

19
Item #016
(though not so marked) Brown & Sharpe
“world’s first practical micrometer.”
While this small micrometer doesn’t look like much,
it cost about twice what an iPhone or iPad costs today
in terms of the one or two week’s wages needed to ac-
quire it. This example has a hole drilled in the frame
by the original owner. While one explanation would
be to keep it handy, another would be to show it off
somewhat like a pocket watch. One might expect a
bit of both. Other examples of this mic have sold for
$700+, but with less wear. Indeed, I’m told the same
mic but of more recent vintage (marked #1, and less
valuable since that was a later version) but less wear
(making it more valuable) recently sold for more than
$850 at a Martin J. Donnelly auction. Despite the age,
this instance looks to have retained its .001 accuracy.

$250 donation

Item #017
Brown & Sharpe “Improved Micrometer Cali-
per” as seen in their 1887 catalog.
1878 and 1884 patent dates, with no number on the
micrometer and the old style thimble. It’s marked with
a fancy stamp (owner? company?) in addition to the
B&S identification. This has suffered numerous dings
etc. over the years, but is still working. Despite the
well (and not so well) used condition, it might be fun
to have.
$30 donation

20
Item #018
#1 Brown & Sharpe 0-1” micrometer with fixed-
friction thimble, slant-line graduations, .0001”
vernier, carbide anvils, and a lock.
Decimal equivalents on the chrome frame. Marked
(on the thimble) as No. Kingston, RI origin. This one
has some signs of wear, a rubbed out marking, and a bit
of a shine to the chrome.
Good working condition in a hinged wood case. It in-
cludes a separate engineering data sheet from North
Kingston.

$30 donation

Item #019
#1 Brown & Sharpe 0-1” micrometer with fixed-
friction thimble, slant-line graduations, .0001”
vernier, carbide anvils, and a lock.
Decimal equivalents on the chrome frame. The thim-
ble has a narrow groove in it (a design element added
to show the fixed versus friction position of the thim-
ble) and is marked with the No. Kingston, RI origin.
Excellent condition in a hinged wood case.

$45 donation

Item #020
#1 Swiss-made Brown & Sharpe 0-1” micrometer
with fixed-friction thimble, a lock, and .0001”
vernier.
This is the same satin chrome frame design as the #599-
1-32 and #599-1 below, but with a different all-steel
thimble design, marked Swiss Made on the smooth
portion. Same tough black plastic lever lock. Mint
condition in its original cardboard box and mahogany
wood case.

$65 donation

21
Item #021
#1 (#599-1-32) Swiss-made Brown & Sharpe
0-1” micrometer with speeder, fixed-friction
thimble, a lock, and .0001” vernier.
Decimal equivalents on the satin chrome frame (along
with “Swiss Made”). The speeder, friction thimble, and
lever lock are a tough black plastic. Great handling
mic. Mint condition in its original cardboard box.

$60 donation

Item #022
#1 (#599-1) Brown & Sharpe 0-1” micrometer
with speeder, fixed-friction thimble, a lock, and
.0001” vernier.
This appears essentially identical to the Swiss-made
#599-1-32 above, but no country of origin is marked
on the micrometer. Same decimal equivalents on the
satin chrome frame. Same speeder, friction thimble,
and lever lock made from a tough black plastic. Great
handling mic. Near mint condition in its original card-
board box.

$55 donation

Item #023
#1 etc. Brown & Sharpe SIX PACK.
Models #1,#8, #10, #11, #11RS etc. Some with slant
lines, four with .0001” verniers, three with convertible
fixed/friction thimbles. These are all in good working
condition, but each has some sort of cosmetic flaw. If
you are sponsoring something like a First Robotics
team here’s a way to make a sort of double donation (to
this scholarship and to the recipients).

$40 donation for the six pack

22
Item #025
#2 Brown & Sharpe 0-1” micrometer with satin
chrome frame, decimal equivalents, fixed-fric-
tion thimble, slant lines, and .0001” vernier.
Marked Pat. No. 2,357,066 on the back. Well designed
micrometer in very good condition with cracked plas-
tic case.

$45 donation

Item #026
#4 Brown & Sharpe 0-1/2” micrometer with an
1884 patent date.
This has wear and damage to the thimble’s knurling.
Decimal equivalents on the frame are all readable. A
good representation of an early micrometer that might
bring $300 in very good condition.

$30 donation

Item #027
#4A Brown & Sharpe 0-1/2” micrometer with a
ratchet, lock, and 1894 and 1902 patent dates.
Works great, with some tarnished spots that should
clean up.
$55 donation

Item #028
#4A Brown & Sharpe 0-1/2” micrometer with a
ratchet, lock, and 1894 and 1902 patent dates.
This one has both anvils rounded. Similar age and
condition to the example above.
$55 donation

Item #029
#4A Brown & Sharpe 0-.5” micrometer with
1891 and 1902 patent dates engraved.
Still quite accurate as well as collectible.

$40 donation

23
Item #030
#4 (but not so marked) Brown & Sharpe 0-1”
micrometer with fixed-friction thimble, carbide
anvils, .0001” vernier, and plain dark gray wrin-
kle finish frame.
Brown & Sharpe retired #4 for ½” micrometers and
started using it for 1” mics. This example is from
around the time of catalog STM-2 (1965). B&S noted
that all its micrometers had completely interchange-
able parts – and for this one I changed the barrel from
slant line to straight line graduations – using the slant
line barrel elsewhere. B&S soon began to offer new
versions of slightly cost-reduced micrometers, without
the satin chrome frame and lock. Like this example,
these had the same precision spindle, thimble, etc. as
their top line models. Excellent condition with origi-
nal cardboard box and (cracked) plastic case.
$40 donation

Item #031
#5RS Brown & Sharpe 0-1/2” micrometer from
the B.C. (Before Chrome) days.
Ratchet, lock, and decimal equivalents in original fin-
ger jointed wood box. A 1928 dated patent number is
on the frame. A tiny micrometer that looks new.

$70 donation

Item #032
#8 Brown & Sharpe 0-1” micrometer with 1884,
1890, and 1894 patent dates.
Ratchet, front lock, side-setting anvil, and decimal
equivalents. Very good condition.

$50 donation

24
Item #033
#10 Brown & Sharpe 0-1” micrometer with front
lock and 1890, 1894, and 1900 patent dates on
the frame.
Ratchet and decimal equivalents on the frame. Very
good condition in worn hinged leather case.

$40 donation

Item #034
#10S Brown & Sharpe 0-1” micrometer in stain-
less steel.
Includes patent numbers 1,629,406 and 1,654,843
(around 1927) around the thimble. Includes a ratchet,
lock, decimal equivalents, and a .0001” vernier. Pretty
much flawless design and condition, in a hinged wood
box.

$65 donation

Item #035
#10S Brown & Sharpe 0-1” micrometer in stain-
less steel.
No patent numbers on this one, but same design as
the #10S above. Near perfect in its original (Bakelite?)
clamshell case.

$65 donation

25
Item #036
#10 Brown & Sharpe 0-1” Digit-Mike with plas-
tic digital thimble and black frame.
This was announced in catalog STM-6 (1972). The
ingenious direct reading mechanism had been around
before – as part of the TESA partnership. With this
version, B&S decided to differentiate itself by going
all black. It also tried to cost-reduce by changing the
housing to plastic. This same micrometer head has
also been seen on Moore & Wright micrometers (who
undoubtably sourced it from B&S/TESA).
There’s a bad news / good news story to this. The bad
news is that every example I’ve seen has micro cracking
to the plastic – a design, material, and process not fully
in control. The good news is that most every example
is still fully functional, including all those here. This
one is in good condition.

$35 donation

Item #037
#10 Brown & Sharpe 0-1” Digit-Mike with plas-
tic digital thimble and black frame.
Another example of the micrometer announced in cat-
alog STM-6 (1972). As the one above, it has carbide
anvils, a lock and decimal equivalents on the frame.
And, as above, the country of origin (Switzerland?
US?) is not marked. This one has more wear and con-
dition issues; but is still fully functional.

$25 donation

Item #038
#10 Brown & Sharpe 0-1” Digit-Mike with plas-
tic digital thimble and black frame, 1972 plus.
Fair to good condition, with paint loss.

$30 donation

26
Item #039
#10-100 Brown & Sharpe 0-25mm Digit-Mike.
Swiss made with a satin chrome frame and the Digit-
Mike mechanism housed in a plastic body. Includes
a lock and thermal pads on the frame. A # marking
is etched neatly on the back of the frame. This exhib-
its the micro cracking common to all the Digit-Mikes
with plastic housings (earlier and later they were met-
al). By the 1987 catalog, B&S Digit Mikes returned to
a metal housing, with an angular sort of satin chrome
frame with molded thermal pads. This older one works
well and has an overall good appearance. It comes in
a TESA holster-like case that could use a bit of plastic
mender.

$40 donation

Item #040
#10 and #20-10 Brown & Sharpe pair of Digit-
Mikes.
These both have satin chrome frames, locks, and
plastic housings for the direct readout. The 0-1” has
decimal equivalents. The 1-2” has thermal pads (with
“Swiss Made” noted on the front one) and a wood case.
Very nice micrometers, despite the “historic” micro-
cracking issue.

$110 for the pair

Item #041
#11 Brown & Sharpe “REX” 0-1” micrometer in
original wood box (the box carries the #11).
Adjustment is the old style moveable anvil retained by
a side screw. This has a square frame design and deci-
mal equivalents on the thimble. Very good condition;
likely from around catalog #27 (1916) to #29 (1924).

$50 donation

27
Item #042
#11 (but not so marked) “REX” 0-1” micrometer
marked “Pat. Pending” on the frame.
Decimal equivalents on the thimble or otherwise as
above, but adds a ratchet. Give the patent pending,
this is likely one of the very earliest REX micrometers.
Good condition.

$55 donation

Item #043
#11 (but not so marked) B&S “REX” micrometer
0-1” with a ratchet and center roll lock.
This is a somewhat later version, with damage to the
paint and knurl. Still, a good way to have an instance
of Brown & Sharpe’s early attempt at two-tier pricing
for its micrometers.

$20 donation

Item #044
#11RS Brown & Sharpe 0-1” micrometer with
ratchet and satin chrome frame.
Repainted frame, otherwise good user micrometer.

$15 donation

Item #045
#11A Brown & Sharpe 0-1” micrometer.
What’s unusual about this one is the bright chrome
thimble and frame. It may have belonged to some-
one at a chrome plating outfit? Ratchet and “I-beam”
style frame normally seen in enamel or wrinkle finish.
Hinged wood box.

$40 donation

28
Item #046
#11RS? Brown & Sharpe 0-1” micrometer.
Possibly built around 1960. This has carbide anvils, a
satin chrome thimble, ratchet, and (unlike most #11
examples) a center roll lock. The frame is the “I-beam”
style in wrinkle black. Very nice condition, save a bit
of chromed tape covering an ID marking.

$30 donation

Item #047
#12RS (marked #12 on the frame) Brown &
Sharpe 0-1” micrometer in satin chrome with
a ratchet, lock, and decimal equivalents on the
frame.
This style first appears in catalog #35 (1951) and has a
larger thimble, satin chrome finish, and carbide anvils.
Good touch and mint condition. Includes its original
case.

$50 donation

Item #048
#12B Brown & Sharpe 0-1” stainless steel mi-
crometer with a ratchet, lock, and decimal
equivalents on the frame.
The ratchet is broken; but a replacement is included in
the box. Calibrate the mic when you make the switch.
Very good condition.

$30 donation

Item #049
#13RS (marked 13B on the frame) Brown &
Sharpe 0-1” micrometer in stainless steel.
Same features and design as the #13RS examples.
Good condition, but initialed “G.E.” on the back and
in a rough (Bakelite?) case. Main attraction – stainless
steel with all the features (ratchet, lock, equivalents,
and vernier reading).

$35 donation

29
Item #050
#13RS (marked 13 on the frame) Brown & Sharpe
0-1” micrometer with a ratchet, lock, and .0001”
vernier.
This has a 1928 patent number marked on the thimble
and a Sept. 15, 1925 patent date finely marked around
the ratchet. The main change is a square cutout frame.
Excellent condition.

$45 donation

Item #051
#13RS Brown & Sharpe 0-1” micrometer with a
ratchet, lock, and .0001” vernier.
Has patent numbers from 1927 and 1928 on the thim-
ble and decimal equivalents on the frame. Excellent
condition, less “Spring” engraved on the inside of the
frame. Since this is a before-chrome finish microm-
eter, that marking can be easily removed if you wish.
Very nice mic with every feature.

$45 donation

Item #052
#13RS Brown & Sharpe 0-1” micrometer with a
ratchet, lock, and .0001” vernier.
Has patent numbers from 1927 and 1928 on the t
himble and decimal equivalents on the frame. Good
condition, no markings, in its original hinged (Bake-
lite?) case.

$45 donation

Item #053
#13RS, #48RS, and #52RS set of Brown & Sharpe
micrometers in a black fitted case.
All have the 1927-28 patent numbers engraved on their
thimbles. As B&S planned for this set, the 1” and 2”
sizes have decimal equivalents and a .0001” vernier.
All have ratchets and locks. This is a near-antique set,
in great condition, with an ease of use and accuracy
that holds up to the best modern standards.

$150 donation

30
Item #054
#13 Brown & Sharpe 0-1” micrometer with
.0001” vernier, a lock, and decimal equivalents
on the satin chrome frame.
Marked “Patent Pending” on the thimble. Fairly recent
vintage with the larger thimble diameter. This is after
the 1920’s-30’s examples and before the fixed-friction
thimble designs. Excellent condition in like-new wood
case.
$35 donation

Item #055
#14 Brown & Sharpe 0-1/2” English Gauge mi-
crometer with gauge equivalents on the frame.
Rounded anvil. Fair condition with wear and tarnish.

$15 donation

Item #056
#15 Brown & Sharpe 0-1” micrometer with the
very old thimble style and 1878 and 1884 patent
dates.
Decimal equivalents on the frame. Super old microm-
eter, with overall tarnish, but clear original markings
and no non-original markings. Quite good for its age.
Includes the old case in poor condition.

$90 donation

Item #057
#15 Brown & Sharpe 0-25mm micrometer with
old style thimble and 1878 and 1884 patent dates.
Very good condition – it looks like metric micrometers
didn’t get much use a century ago here in the States . . .

$80 donation

31
Item #058
#15 Brown & Sharpe 0-1” micrometer with 1884
patent date.
Anvil screws in/out to adjust. Very good condition for
its age.

$70 donation

Item #059
#15 Brown & Sharpe 0-1” micrometer with deci-
mal equivalents on the frame and screw-in anvil
adjustment.
Heavy construction and large numerals for ease of
reading, including in steel mills. An old mic approach-
ing mint condition in its original wood box.

$60 donation

Item #060
#15 Brown & Sharpe 0-1” micrometer with deci-
mal equivalents on the frame and screw-in anvil
adjustment.
Heavy construction and large numerals for ease of
reading, including in steel mills. This is a second ex-
ample, whose only flaw is a faint (can’t read it) inscrip-
tion light on the back of the frame.

$40 donation

Item #061
#17 Brown & Sharpe 0-1” micrometer with a
side screw lock.
This is the heavy frame design for gauging hot metal,
from the early A.C. (After Chrome) days. Some flaws
in the chrome, but overall good function and appear-
ance.

$25 donation

32
Item #062
#19 Brown & Sharpe 0-1” micrometer with the
very old style thimble (with a single narrow
knurl at the end).
Frame is marked with 1878 and 1884 patent dates plus
decimal equivalents. Very old micrometer. A few
small dings to the frame, but otherwise very good con-
dition.

$70 donation

Item #063
#19RS (marked #19 on the frame) Brown &
Sharpe 0-25mm micrometer in black hinged
case.
Plain steel finish with a 1925 patent date on the speed-
er/ratchet. Adjustment is through side-mounted screw
holding the frame-side anvil. Includes a B&S 1” round
standard. Fair condition.

$25 donation

Item #064
#19RS (marked #19 on the frame) Brown &
Sharpe 0-1” micrometer in hinged wood case.
Includes ratchet and decimal equivalents. Tarnished,
though still good condition.

#25 donation

Item #065
#19 Brown & Sharpe 0-25mm micrometer.
Plain steel finish. Adjustment through side-mounted
screw holding the frame-side anvil. Very good condi-
tion.

$25 donation

33
Item #066
#19 Brown & Sharpe 0-1” micrometer.
Plain steel, no ratchet. Same adjustment as the #19RS
metric mic. Clear markings, no engravings, works well.

$15 donation

Item #067
#20 Brown & Sharpe 0-1” micrometer with the
side screw anvil adjustment and just an 1884
patent date on the frame.
Includes a ratchet, decimal equivalents on the frame,
and a .0001” vernier. This model appears in my 1899
(#101), 1900 (#102) and 1907 (#109) catalogs and
probably dates from that era. Some dings, but overall
good condition with no extra markings. Wood box
and paperwork.

$45

Item #068
#22 Brown & Sharpe 0-1” micrometer with an
1894 patent (along with decimal equivalents) on
the frame.
Includes a side clamp screw for the spindle. This mi-
crometer appears in the 1899 catalog. Very good con-
dition in wood box.

$65 donation

Item #069
#31 Brown & Sharpe 0-2” micrometer.
Similar to the #45 but significantly older. Has an 1884
patent date on the back, the old single-knurled thimble
and an unusual spindle lock. Excellent condition with
a 1” standard and a well worn box. Valuable microm-
eter.

$100 donation

34
Item #070
#38 Brown and Sharpe 1-2” micrometer with
1902 patent date and decimal equivalents.
$20 donation

Item #071
#45 Brown & Sharpe 0-2” micrometer with 1884,
1887, 1890, 1894 (faintly), and 1900 patent dates
on the frame.
Must have been very proud of their patent history when
this was made. This has a missing front lock nut. The
original stampings are clear, but this has a well worn
look to it.

$20 donation

Item #072
#45 Brown & Sharpe 0-2” micrometer with 1884
and 1902 patent dates on the frame.
No non-original marks. Ratchet, locks, etc. are all in
good working condition. The decimal equivalents still
look sharp.

$45 donation

Item #073
#45 Brown & Sharpe 0-2” micrometer with 1884,
1890 and 1902 patent dates on the frame.
This is in outstanding condition for its age, still clean
and bright. Includes an old case.

$70 donation

35
Item #074
#45 Brown & Sharpe 0-2” micrometer, probably
from the 1940’s.
Includes ratchet, lock, decimal equivalents, etc. Excel-
lent condition, with a B&S 1” standard, in wood box.

$50 donation

Item #075
#48 Brown & Sharpe 1-2” micrometer with 1902
patent date, with standard, in wood box.
$35 donation

Item #076
#48 Brown & Sharpe 1-2” micrometer, 1928 pat-
ent number, in good plush fitted case.
Has 1” round standard, a lock, and decimal equiva-
lents. Very good condition save for initials discretely
place inside the throat of the micrometer – easy to re-
move without changing the appearance of the microm-
eter. You might match this up with a #53.

$45 donation

Item #077
#48 Brown & Sharpe 1-2” micrometer.
Looks close to new. This had it all, beginning in the
1950’s: satin chrome, ratchet, lock, decimal equiva-
lents, carbide anvils, and a .0001” vernier. In good case
with 1” round B&S standard.

$45 donation

Item #078
#48 Brown & Sharpe 1-2” micrometer, near the
same condition as the above.
Satin chrome, ratchet, lock, decimal equivalents, car-
bide anvils, and a .0001” vernier. No case.

$35 donation

36
Item #079
#52 Brown & Sharpe 2-3” micrometer with
ratchet, front side lock, and side screw anvil ad-
justment type.
Has 1890, 1894, and 1900 patent dates on rear of frame.
Good condition in original case, which includes a rare-
ly seen B&S standard of the 2” round type. Pair it with
a similar vintage 1-2” mic.

$50 donation

Item #080
#53 Brown & Sharpe 2-3” micrometer with
ratchet, center lock, and .0001” vernier.
Very nice condition, with a standard, in plush fitted
case. Pair this with a B&S #48, also in plain steel finish
steel.

$40 donation

Item #081
#59 Brown & Sharpe 0-1” micrometer with the
square REX-style frame and marked “Patent
Pending” on the thimble.
Includes a center lock. The enamel on the frame is
rough, but the overall feel and adjustment is still good.

$25 donation

Item #082
#59 Brown & Sharpe 0-1” micrometer with a
lock.
This is dated after the “REX” designs, but before
chrome. Good condition, except worn enamel on the
frame. Hinged wood box could use a clean up.

$20 donation

37
Item #083
#61 Brown & Sharpe 1-2” micrometer with the
square B&S trademark and a 1902 patent date
on the back of the frame.
Includes a center roll lock.

$40 donation

Item #084
#62 Brown & Sharpe 1-2” micrometer with the
same lock, trademark and 1902 patent date as
the #61.
The difference is that this one has a .0001” vernier.
Good condition.

$50 donation

Item #085
#65, #63, #61, #10 set of four Brown & Sharpe
micrometers; all with a December 30, 1902 pat-
ent date engraved on the back of the frame.
Fairly uncommon to find a group of hundred year old
micrometers in such relatively good condition. Each
has a lock and all the larger sizes have an older style of
B&S frame. The calibration adjustment is at the anvil
end. The 0-1” is a #10 with a .0001” vernier, a ratchet,
and decimal equivalents on the frame. The 1-2” is a
#61 with a ratchet and lock. The 2-3” is a #63 with a
ratchet and lock. The 3-4” is a #65 with a lock and a
slightly more recent date (along with the #10) since it
uses the “square logo” that first appeared around 1905.
The others are likely close to the patent date. These
look to still have the accuracy one might get with a
modern set, with a bit of history as well.

$120 donation for set of 4

38
Item #086
#71 Brown & Sharpe micrometer 0-.3”
with a patent date of November 6, 1894. Fairly rare,
old, and in excellent condition for its age. The large
flat anvils are especially useful for measuring paper and
other compressible materials.

$55 donation

Item #087
#75?? #233? Brown & Sharpe 0-1/2” bench mi-
crometer.
The micrometer is completely unmarked, yet identi-
cal in style, details (ratchet, etc.), and dimensions to
various B&S micrometers going back to the late 1890’s.
The earliest version of these were attached from the
bottom (like this one). Later version had a bench mic
frame, beginning around 1929. What’s different from
those seen in my catalogs (1892, 1899, 1900 on . . . ) is
the old-style adjustment system with an adjustable an-
vil locked with a sideways screw. One knowledgeable
source suggests this example was made between 1916
and 1920. In any case, this remains a silky smooth
micrometer that would do well mounted to a new base.

$100 donation

Item #088
#102 Brown & Sharpe heavy micrometer caliper
1-2” with a heavy ratchet and lock. I-beam style
frame.
Uncommon mic in good condition.

$65 donation

Item #089
#176-1 Brown & Sharpe 0-1” multi-anvil mi-
crometer.
English made, with a friction thimble, lock, and .0001”
vernier. Tiny bit of wear to a printed number, but
overall excellent condition. Comes with a B&S clam-
shell case.

$70 donation

39
Item #090
#176 Brown & Sharpe 0-1” multi-anvil microm-
eter with extra anvils and case.
This was made by B&S at their No. Kingston plant. Note
the different design of a B&S multi-anvil mic made in
England. All satin chrome with fixed-friction thimble
and lock. Cool micrometer in near mint condition.
Last one I noticed on eBay went for $139+ without the
box and extras (8/2/08).

$75 donation

Item #091
#200, #201, and #202 Brown & Sharpe 0-3”
mechanical digital micrometers with rotating cube
windows. These are mechanical marvels, easy to read
and very accurate. Given the high cost of manufac-
turing and a selling price well above electronic digital
micrometers ($300 to $400 each a decade ago), these
Swiss-made mics are hard to find and may be increas-
ingly valued. Set is older style in excellent shape, ex-
cept that the foam linings of the cases have been re-
moved due to deterioration.

$290 donation

Item #092
#215 Brown and Sharpe 0-1” disk micrometer.
This is a B.C. (Before Chrome) era model with its
wooden box and paperwork. Center roll lock and dec-
imal equivalents on the frame. Very good condition.
$45 donation

Item #093
#215-like Brown and Sharpe 1-2” disk microm-
eter.
A good match to the 0-1” Before Chrome model above.
Painted frame.

$35 donation

40
Item #094
#215 Brown and Sharpe 0-1” disk micrometer.
This is an A.C. (After Chrome) era model with the larg-
er fixed-friction thimble, a lever lock, slant line gradu-
ations, and a .0001” vernier. Decimal equivalents on
the frame.

$50 donation

Item #095
#219 Brown & Sharpe 0-1” blade micrometer
with black wrinkle frame and original card-
board box.
Overall very good shape, with just the faintest inscrip-
tion at the end of the thimble (easily covered with a bit
of Mylar tape). Blade micrometers are meant reach
into small features, such as snap-ring and cylinder-ring
grooves. Good ones (like this) run about $200-300.

$85 donation

Item #096
#221-1 Brown & Sharpe 2-3” blade micrometer
in near new condition with original case.
This one is made in England. This size is prized by
internal combustion engine enthusiasts; anyone with
pistons in the 2-3” size. It’s not just a blade microm-
eter, it’s of an age when most everything in England
was groovy.

$110 donation

Item #097
#225 Brown & Sharpe 0-1/2” “English Gage” mi-
crometer with ball anvil and ratchet.
The elegantly cut-away style frame has gage equivalents
(1 to 30) stamped in its small frame. This plain steel
style is seen in the B&S 1941 catalog (#34) but not its
1951 catalog (#35). Excellent condition.

$55 donation

41
Item #098
#229 Brown & Sharpe Swiss-made wire microm-
eter.
Measures most anything within its geometric con-
straints. All satin chrome. Gorgeous tool in original
case.

$60 donation

Item #099
#232 Brown & Sharpe 0-1/2” paper gauge mi-
crometer.
Half inch flat anvils and 2” deep frame. Satin chrome
thimble and wrinkle finish frame. Lightly marked.

$35 donation

Item #100
#233RS Brown & Sharpe 0-.5” bench microm-
eter, self-contained in a fitted wood box.
Includes large thimble, directly reading in .0001” in-
crements, and a ratchet. Beautiful little micrometer in
excellent condition. The enclosed paperwork dates it
from 1950. #1 example.

$90 donation

Item #101
#233RS Brown & Sharpe 0-.5” bench microm-
eter, self-contained in a fitted wood box.
Includes large thimble, directly reading in .0001” in-
crements, and a ratchet. Beautiful little micrometer in
excellent condition. The enclosed paperwork dates it
from 1953. #2 example.

$90 donation

42
Item #102
#233RS Brown & Sharpe 0-1/2” bench microm-
eter of 1950+ vintage.
Has a ratchet, carbide anvils, and a large satin chrome
spindle that reads directly to .0001.” This has the #1712
stamped and will look better without the broken but
included case. #3 example.

$45 donation

Item #103
#237 Brown & Sharpe 0-1” by 3” deep throat
micrometer (a.k.a. “rolling mill gauge”) with a
ratchet.
Adjustment is by a set-screw retained anvil (older
style). This style of frame etc. was phased out during
the WWI years. Very good condition in a good case.

$70 donation

Item #104
#239 Brown & Sharpe 1” by 6” deep throat mi-
crometer with a finger hold through the frame.
Same idea as the #237 rolling mill gauge; but with a
deeper frame. Very good condition.

$80 donation

Item #105
#245 Brown & Sharpe 0-1/2” bench micrometer
in hinged wood case.
Direct reading to .0001” on either the large thimble or
dial comparator. Ugly (but restorable) finger-jointed
wood case with very nice and highly accurate microm-
eter within. Includes a lock, measuring platform, and
retractable anvil. These cost $350 four decades ago; a
bit less than $2000 in today’s dollars.

$150 donation

43
Item #106
#245 Brown & Sharpe 0-1/2” bench micrometer
in hinged wood case.
Direct reading to .0001” on either the large thimble or
dial comparator. Nice finger-jointed wood case with
very nice and highly accurate micrometer within. In-
cludes a lock, measuring platform, and retractable an-
vil. Even better condition than the #245 above.

$170 donation

Item #107
#250 Brown & Sharpe inside micrometer .2” to
1” range.
This style first appeared in the early 1900’s. Excellent
cosmetic and working condition.

$50 donation

Item #108
#252 Brown & Sharpe .5” to 1.5” inside microm-
eter.
An older style (polished steel) in its original black
leather case. Case is marked “141” – the micrometer
is in near mint condition.

$45 donation

Item #109
#263 Brown & Sharpe 1-2” inside micrometer, as
seen in the Museum of Modern Art collection!
This includes a small micrometer head, two inter-
changeable rods, two spacers, and a small adjustment
wrench – all in the original wood box. It’s also one of
the handful of tools selected by MOMA curators for
display.

$55 donation

44
Item #110
#599-1-9999 Brown & Sharpe new old stock fit-
ted mahogany wood case, itself in the original
cardboard box.
As furnished with many #1 and other 0-1” and 0-25”
micrometers. Consider this if you buy a naked pride-
of-ownership micrometer – a more modest approach.

$15 donation

Item #111
#599-3-36 Brown & Sharpe 2-3” micrometer.
Swiss made with fixed-friction thimble. Black frame
with a control number on the back; otherwise very
good. This would round out a high quality 1” and 2”
pair.

$30 donation
Item #112
#599-10-100-1 Brown & Sharpe 0-25mm Digit-
Mike.
Swiss made. New old stock direct reading micrometer
in original packaging. See other Digit-Mikes listed un-
der #10.

$95 donation

Item #113
#599-40-110-1 Brown & Sharpe 75-100mm Dig-
it-Mike.
Swiss made. Excellent condition in wood box (foam
needs replacing).

$95 donation

Item #114
#599-20-6 Brown & Sharpe 1-2” micrometer.
Fixed-friction thimble, slant line graduations. Very
good condition in original cardboard box.

$25 donation

45
Item #115
#599-20-3 Brown & Sharpe 1-2” micrometer.
Fixed-friction thimble, slant line graduations, plus lock
and carbide faces. Excellent condition in original card-
board box.

$30 donation

Item #116
#599-281-10-1 Brown & Sharpe/TESA 20-25mm
hole micrometer (Intrimik); for measuring bore
diameters to an accuracy of .005mm.
This is marked TESA (Swiss made) on the tool and B&S
on its original box; probably from a time when B&S
had just bought TESA. It’s included here to give one
example of three point internal measurements. The
advantage of a 3-point hole micrometer compared to
2-point alternatives is both greater ease of measuring
and the ability to detect out-of-round conditions. In-
deed, many holes have lobing; and there is even a tool
to drill square holes! New price on these is $549 (Long
Island Indicator, etc.). This one looks to have been
checked into the Bendix calibration lab in 1978, and
never used. It’s mint. Most shops (including mine)
will have a wide range to cover various bore sizes, from
makers like B&S, Fowler/Bowers, Lufkin/Etalon, and
Mitutoyo.

$100 donation

Item #117
#605 (but not yet so numbered) Brown & Sharpe
depth micrometer 0-2.5”with a 4” base.
This style, with the notched/adjustable rod and no
model number engraved dates from the early 1900’s..
Very nice condition and still accurate.

$50 donation

46
Item #118
#1011 Brown & Sharpe 0-1” satin chrome mi-
crometer with a fixed-friction thimble, carbide
anvils, decimal equivalents, and a lock.
Patent number 2,357,066 marked on the back. Very
well made micrometer (Providence, RI origin) from re-
cent decades Slant line graduations and .0001” vernier.
Well designed (better than most current versions) in
excellent condition. Includes original plastic box.

$50 donation

Item #119
#1011 Brown & Sharpe 0-1” satin chrome mi-
crometer with a fixed-friction thimble, carbide
anvils, decimal equivalents, and a lock.
This differs slightly from the above. Patent number
2,357,066 marked on the back; along with “Pat. Pend-
ing” and the model number 1011 (which is on the front
of the other example). From the B&S Providence, RI
plant. Same excellent design and condition as the
above example, in a previous owner’s box.

$50 donation

Item #120
Brown and Sharpe 0-3” micrometer set in like-
new B&S fitted plush case
(itself in the original cardboard box). Includes a near
perfect all-satin B&S #1 with all the options and deci-
mal equivalents, plus the intended matching 1-2” and
2-3” (near mint) with wrinkle frames and standards.
All are North Kingston made with convertible friction/
fixed thimbles, locks, carbide faces, and .0001” reading
verniers. A really nice set.

$175 donation

47
Item #121
New old stock Brown & Sharpe
interchangeable anvil mic for 0-4” range. Makes a
good complement to a 0-1” mic; setting the larger mic
to size as needed.

$80 donation

Item #122
Brown & Sharpe
0-3” mechanical digital micrometers (Digit-Mikes)
of a different design than the 200 series. These are
easy to read and very accurate. The 2-3” size is from
the last years of manufacture; after B&S figured that
foam linings would deteriorate. Given the high cost of
manufacturing and a selling price well above electronic
digital micrometers (over $1200 for the three), these
Swiss-made mics will be increasingly valued. Mics are
in essentially new shape, at a fraction of new cost.

$290 donation

48
Item #123
Brown & Sharpe 0-6” micrometer set in B&S fit-
ted wood case.
The micrometers were made in North Kingston, RI and
include convertible friction/fixed thimbles, slant line
graduations, lever locks, carbide anvils and calibration
standards. Accurate with a comfortable (IMO) feel.
This was my personal set. Very good condition over-
all. See the 6-7” micrometer below to fill our your set
to a lucky and sometimes useful 7.

$385 donation

Item #124
Brown & Sharpe 6-7” micrometer; a comple-
ment to the 0-6” set.
Dingy wood case hides an excellent condition microm-
eter with fixed/friction thimble, carbide anvils, a lock,
and calibration standard. Perfect match to the 0-6” set.

$35 with 0-6” set; otherwise $65

Item #125
B&S / Valco crimp-height micrometer in mint
condition.
Totally unmarked satin chrome frame with mechanical
digital mechanism (B&S “Digit-Mike”) with a lock and
friction thimble all made by Brown and Sharpe. The
anvils are specially shaped to measure the integrity of
electrical crimp connections.

$55 donation

Item #126
B&S / York Machinery & Supply Co. (York, PA)
crimp height micrometer with a body made by
Brown & Sharpe’s North Kingston facility.
All satin chrome with convertible friction/fixed thim-
ble and lock. The anvils are shaped to measure the
integrity of electrical crimp connections. Essentially
mint condition.

$40 donation

49
Item #127
B&S 50-75mm micrometer with fixed-friction
thimble, carbide anvils, and a lock.
No number on the micrometer. Good condition.

$20 donation

Item #128
Swiss-made Brown & Sharpe 0-1” micrometer
with fixed-friction thimble, carbide anvils, black
frame, and a .0001” vernier.
No number on the micrometer. This one is distin-
guished by the straight line knurling on the thimble
and the plastic (those have held up OK) lever for the
lock. It also has a slight convexity to both anvils. Like
many of the similar B&S models this is a pride-of-own-
ership mic. Excellent condition in hinged wood box.

$55 donation

Brown & Sons (Chicago)

Item #129
Brown & Sons 0-1” micrometer with ratchet,
lock, and decimal equivalents.
Marked No. 100 on reverse side of the frame. Fairly
decent build, but with a thimble whose size, number-
ing, and knurling look much like the “Brownie” mi-
crometers.

$20 donation.

50
Cadillac Gage Company
(Detroit, MI ) was a division of Ex-Cell-O Corporation by about 1956. In addition to precision gage
manufacture, primarily for the auto industry, it made guns and many Vietnam-era military vehicles.
Textron acquired Cadillac Gage in 1986 and merged it with their Marine division (to become Marine &
Land Systems) in 1994 -- all focusing on the defense industry .
Item #130
Cadillac Pla-Chek 0-6” height gage, plus a 6” ris-
er; made in West Germany.
The large diameter micrometer head reads directly to
.0001” and steps are placed at every inch increment to
touch off a test indicator. Forget Coordinate Measur-
ing Machines (much less laser scanning) – this is what
I saw being used in Ford and other auto factory QC
labs back in the 70’s.

$110 donation for gage and riser

51
E.J. Cady & Co.
(Chicago, Illinois) was founded by Elijah Jess Cady. He became a commissioned paper broker in 1881
and started his business in 1893. By 1915 he had invented and was making paper micrometers, paper
scales, and burst testers. The family-owned company (five generations) describes itself as “precision mea-
suring and testing instruments since 1893.”
Item #131
E. J. Cady &Co “Automatic Micrometer” meant
for measuring paper thickness.
Graduated in .001, 1/64, and point sizes. A reliable de-
sign, with older examples such as this one still in fine
working condition.

$90 donation

Robert W. Carson
Inventor of the Carson Electronic Micrometer
Item #132
Carson Electronic Micrometer 0-1” (patented
Nov. 17, 1942) with precise vertical measuring
head and vacuum tube power box.
Paperwork for patent #2,302,104 is included. This is a
nifty Buck Rogers era micrometer with .00001 sensitiv-
ity (10 millionths – around the range of the Van Keur-
en Light Wave micrometer). Condition or accuracy
is not known. A prudent person might run it at half
voltage (with a Powerstat / autotransformer) for while
to reform any electrolytic capacitors hiding in the chas-
sis. Or, open it up and take a look first. Marked “49”
inside the control box; perhaps the 49th unit in a small
production lot? Very good cosmetic condition.

$120 donation for the set

52
Cary Le Locle
(Le Locle, Switzerland) was a maker of micrometers, comparators, gauge blocks, and other precision
tools; and was located amidst the vibrant Swiss watchmaking industry. Cary became part of TESA; and,
along with Brown & Sharpe, it became part of Hexagon AB. Cary remains active as a TESA brand.
Item #133
Cary Le Locle 0-15mm bench micrometer with a
.001mm comparator.
This is a gorgeous bit of Swiss wizardry, built to watch
tolerances (including a fully jeweled movement in the
comparator) and sold into the watchmaking industry.
The satin chrome thimble reads directly to .01mm and
has a plastic cover to avoid thermal effects. There is
also a spindle lock (it sort of hard ratchets in this posi-
tion), which allows either fixed comparative measure-
ments or smooth direct rotation. A wide variety of
specialized anvils are available. Four extra pairs of dif-
ferent types are included – themselves worth roughly
the donation price. The micrometer includes a parts
support and an anvil release. At the time this was
likely built, it cost about as much as a VW bug. Near
perfect condition in original wood case.

$500 donation

Central Die Casting

Casting (Chicago, IL) were makers of the inexpensive
Handi-Mikes (a.k.a. “The Mighty Midget).

Item #134
Handi-Mike
(USA) 0-.5” with die cast frame. Inexpensive microm-
eter, typically sold through five-and-dime stores such
as Woolworth’s.

$7 donation

Item #135
Handi-Mike (USA) 0.5” with chrome plated
frame.
$12 donation

53
Item #136
Handy (USA) 0.5” micrometer
with die cast frame. Likely an earlier version of the
Handi-Mike.

$7 donation

Central Scientific Company

– see Scherr-Tumico.

The Central Tool Company

The Central Tool Company (variously of Provi- the automotive market (slightly higher standard),
dence, Auburn/Cranston, RI) has a long history, be- and in making micrometers for others to distribute
ginning in 1908, trying to find niches in the highly under their own brand names. The Central Tool
competitive precision tools business. The company Co. more recently calls itself Central Tools and has
has since been in the same location since 1912 with built mics branded “MG,” “National,” and “MG/
early micrometers marked “Auburn” and later ones National.” The MG/National Specialty Co. was
marked “Cranston.” Some early analog microme- located in N.Y. city. Central also built gold-tone
ters were nicely made; and their mechanical digital versions for Chrysler to use as graduation gifts for
micrometers were a competitive high point in terms its “Master Technician” automotive students. The
of technical sophistication. In later years their mi- Welch Scientific Co. sold Central-built micrometers
crometers have been of moderate quality (still us- under its own brand name. I also have Central-built
able and accurate), but often built to a price point. mics with the logos “MAC” and an intertwined
Toward the last half of the twentieth century the “MW.” Perhaps most to its credit is that the com-
company specialized in tools for trade schools (for pany recently celebrated its 100th anniversary, still
example, lower priced “Apprentice” micrometers), as a family-owned company.
Item #137
This example is a mint condition Welch Scien-
tific Company
micrometer built for them by Central Tool. Give it to
a chemist friend.

$20 donation

Item #138
W.M. Welch Manufacturing Co. 0-25mm mic
made by the Central Tool Co.

$20 donation

54
Item #139
This example is a Chrysler Award micrometer.
It’s hard to know if Master Technicians were delighted
to receive a micrometer or a bit disappointed to get the
equivalent of a Timex instead of a Rolex. In any case,
the spindle of this one is stiff from years of congealed
oil and no use. Perhaps buy it to impress your friends
at Fiat, the new owners of Chrysler?

$20 donation

Item #140
This is a 0-100mm interchangeable anvil set,
built to a higher standard (friction thimble, etc.) than
many Central micrometers. It would be an affordable
way to add metric capabilities.

$55 donation

Item #141
This is an older 0-4” interchangeable anvil set,
built to a higher standard than many Central microm-
eters. It has analog reading to tenths and a mechanical
digital readout for hundredths and thousandths. The
anvils also change easily.

$55 donation

Item #142
Omega 0-1” micrometer made by the Central
Tool Co.
This is the same micrometer sold as under the MG and
Sears brands as an apprentice micrometer.

$12 donation

55
Item #143
0-1” & 1-2” set of “Apprentice” micrometers un-
der the MG/National brand,
designed to be sold through schools to the students of
various US apprentice programs. The set has the ba-
sics, a friction/ratchet and sufficient accuracy to mea-
sure .001. The 1” size even has the added cost of a frac-
tion/decimal table on the frame – a likely requirement
for students. Good set for a mechanically inclined
child. Despite the “National” name, they won’t destroy
a national treasure in a few years of abuse. Accuracy
adjustment is by a screw to the anvil.

$30 donation

Item #144
This is a 0-25mm & 25-50mm set under the MG
brand.
It is built to a higher standard than their “Apprentice”
series, including a better adjustment to zero, a lock,
and an adjustment for spindle wear. Prepare someone
for a metric future!

$40 donation

Item #145
Set of five Central Tools (Cranston, R.I.) mi-
crometers covering the range 0 to 5”
These are of decent quality with locks, a ratchet thim-
ble, and the usual goodies. The 0-1” has a chrome
frame with decimal equivalents. A U.S. made set in
mostly near new condition, perhaps 40-50 years old, at
a bargain cost

$95 donation

56
Item #146
0-1” MG Tool micrometer made by Central Tool
Co.
Factory inspection date of May 10, 1969. This has fea-
tures that are fairly uncommon for Central, including
a friction (rather than ratchet) thimble, a knurled type
(rather than lever) lock, and carbide anvils. Probably
the best Central mic of this era. Slightly stiff thimble –
needs an oil change.

$30

Item #147
Set of 3 Central Tools micrometers.
The largest (2-3”) of the lot is branded “MW” and has
seen use and wear. All have locks and a friction thim-
ble and all are from the Cranston, RI facility. Good
entry level user set.

$40 donation

Item #148
Set of four “MW” micrometers made by the Cen-
tral Tool Co.
Equipped with locks, ratchet, and .0001 verniers. Black
wrinkle frame. A reasonable quality user set.

$45 donation

Item #149
The what-happens-when-engineers-are-in-
charge micrometer.
Jacques patent (April 25, 1911 etc.) for the direct read-
ing digital mechanism. 3-4” size. This is one of the
earlier mechanical digital mics and a sophisticated
and robust design. Near a century later, it still works
just fine. However, it would not be surprising that the
manufacturing cost was greater than many could af-
ford.

$70 donation

57
Item #150
The what-happens-when-MBA’s-take-over three
pack.
For an example of what product differentiation might
look like, when engineers are in charge, take a look
at my Central Tool Co. “Jacques patent” mechanical
digital micrometer built almost 100 years ago. For
an example when less technically inclined folks are in
charge, check out these micrometers sold under the
Central, MG, and MAC names and only the slightest
product differentiation (the locks, chrome or wrinkle
black frames). One wonders if MAC tools resold these
mics; the quality would be just barely adequate for the
brand in my opinion. It’s now a standard practice
(think of Whirlpool, Kenmore, Roger, and KitchenAid
plus tiny SKU differences that might price match guar-
antees a joke). Still, to its credit, Central Tools is still a
going company. Three mics, one donation. Buy it for
a budding MBA, a business professor, or send it in an
unmarked envelope to your boss’s boss?

$50 donation

Item #151
Central Tool Co. 0-6” beam micrometer marked
Pat. Pend.
(Patent Pending). Early micrometer in good condi-
tion. Has initials on the rear side (BTC), which could
be removed with wet/dry paper. The idea of this de-
sign was to get the reach and versatility of calipers, with
the accuracy of a micrometer. Similar beam microm-
eters were made in the late 1800’s and early 1900’s by
Starrett (some examples in this collection), Brown &
Sharpe, and others

$95 donation

Item #152
Central Tools .3 to 1.3” disk brake micrometer.
To measure brake rotor thickness, thickness variation,
and score depths (the pointed end). Actually pretty
well built for the task; though a deeper throat is now
common.

$30 donation

58
Item #153
Central Tool Co. 0-15mm watchmaker’s mi-
crometer.
Tiny anvils for small parts and to fit in grooves. Nicely
made older micrometer, from the Auburn era.
$35 donation

Item #154
Central Tools 0-3” micrometer set in padded
black case.
This is an older set (1930’s?) of good quality construc-
tion.

$60 donation

Item #155
Central Tool Co. 0-1” and 1-2” micrometers;
among the earlier ones made (likely 1920’s; pre-
Depression).
One unique feature of these is the knurled collar sur-
round the frame and spindle. One presumes the pur-
pose of the screw hole was to provide an oiling point?

$45 donation

Item #156
Older style Central Tool Co. 0-1” micrometer
with a cool logo on the back side
(only time I’ve seen this) and paperwork referring to
the 1918 patent for the friction thimble

$30 donation

59
Item #157
Early 1-2” Central Tool Co. micrometer.
The frame design is very similar to early (e.g. the 1902
patent set) B&S micrometers, but with a calibration
adjustment (front of the thimble) that looks like Reed.
Hard to know who was

$30 donation

Item #158
One of the earlier Central Tool Co. metric mi-
crometers, 0-25mm.
“Certified Accuracy!”

$25 donation

Item #159
Satin chrome Central Tool Co. 0-1” micrometer
with friction thimble and wood box.

$25 donation

Item #160
Nice, older Central Tool Co. (Auburn) 1-2” mic
with widely spaced and easily read decimal equivalents
of fractions front and back. Pair it with one of the 0-1”
mics. Includes a standard.

$25 donation

Item #161
Central Tool Co. 0-1” ball end mic with satin
chrome, decimal equivalents, ratchet lock, and
wood box.
The ball end anvil is designed to fit inside tubing and
pipe to measure its thickness. It can also be used to
measure most flat pieces.

$25 donation

60
Item #162
Central Tools, Inc. 0-1” mechanical digital mic
made by Slocomb.
Slocomb makes a very good mechanical digital mi-
crometer (with patents going back decades). So, here’s
a very good tool, with a somewhat lesser brand (IMO)
affixed. Pretty cool, with .0001 vernier, friction thim-
ble, carbide faces, and pretty much mint condition.
Donation is half of new price (years ago).

$45 donation

James Chesterman & Co.

(Sheffield, England) was established in 1829. Known as a quality maker of patent measuring tapes, rules,
and other precision measuring instruments. The company was still publishing an extensive catalog (124
pages) in 1954. In 1963 an amalgamation with John Rabone & Sons created Rabone Chesterman; which
was subsequently bought by Stanley Tools. A book titled “The first 200 years: a short history of Rabone
Chesterman Limited” was published in 1984.
Item #163
Chesterman 0-1” micrometer, all satin chrome
with ratchet, lock, .0001 vernier, and decimal
equivalents on the frame.
Well made in excellent condition. Probably dating be-
fore 1963.

$45 donation

Chicago Brand
is an importer of low cost chinese tools.
Item #164
Chicago Brand 0-1” and 0-25mm electronic dig-
ital micrometer 0-1” -- unused in original wood
box.
You decide – compare with the Mitutoyo digital elec-
tronic micrometer – fair trade?

$25 donation

61
Davis & Thompson Co.
(Milwaukee, Wis.) was established in 1918. It is listed in American Machinist, Volume 53 (1920) as
the maker of the Davis Duplex Continuous Milling Machine. This was a complex affair; with multiple
spindles for end milling to length. The company is still listed as doing business in Wisconsin.
Item #165
Davis & Thompson 10-13” adjustable range mi-
crometer with a hollow chromed frame.
This has a bright chrome frame, similar to those made
by the Tubular Micrometer Co., fitted to a Brown &
Sharpe #294 micrometer head, with ratchet. This is of
a type made from the 1920’s to 50’s. The chrome has
small flaws, but the overall appearance is pretty good.

$60 donation

Deltronic Corporation
(Santa Ana, CA) is best know as a manufacturer of thread and plug gages, along with optical comparators
and video inspection systems. The company boasts “the name Deltronic has become synonymous with
accurate measurement” (the emphasis theirs). The core competency, at least for the gages, is precision
grinding. The plug gage here is just for kicks; though note that these are commonly made to 40 mil-
lionths tolerances; and can make reasonably good mic standards.
Item #166
Deltronic “Go” (green) “No Go (red) plug gage
for those who see the hole ¾ full.
If California companies can have “talking sticks” to
help run their meetings, some project manager can
surely use this to give a thumbs up (green!) or thumbs
down (red).

$12 donation

62
Ferdinand Durand
(Paris). Judging from the one example of a micrometer, this appears to be an older company. The only
reference to company history I’ve found is this 1920 catalog ---- and a smilar 1932-dated Durand catalog:
Catalogue Illustré De La Manufacture De Petit Outillage Mécanique Et D Instruments De Précision.

Item #167
Fernand Durand 150mm micrometer.
An older style micrometer with a lock and thermal pads
similar to that used by Starrett around 1900. The frame
appears to be carefully sawn by hand, then cleaned up
on a grinder. Overall, excellent quality. Note the tiny
(eagle??) logo by the fixed anvil. I’d be inclined to clean
it up, make a stand, and gently clasp a Dassault CD be-
tween the anvils?

$55 donation

E.D.A.
(France)
Item #168
0-15mm micrometer sold by HR (distributor) into the
watch and clockmaking industry. Very nicely made
small metric micrometer.

$30 donation

63
Elgin National Watch Co.
(Chicago, IL) was incorporated August, 1864. The opened their watchmaker’s college in 1921 and closed
it in 1985. A possible connection to their “Sapphire Tipt” micrometer is that all civilian work was sus-
pended during WWII to concentrate on military watches, chronometers, and Sapphire bearings for aim-
ing systems.
Item #169
Elgin 0-1” micrometer with sapphire jewel
tipped anvils made for them by the Tubular Mi-
crometer Co.
Mint condition with .0001 vernier in a fitted wood
case. This was undoubtedly destined for their affiliated
watchmakers and watch shops. The notion of sapphire
anvils is an interesting (and costly) bit of differentiation
for that trade. Probably dates to the 1950’s.

$125 donation

Etalon
(Rolle, Suisse/Switzerland) was originally a brand of Pierre Roch S.A.R.L. “Etalon” is from the French
étalon, meaning both a stallion and a standard in metrology – and the company’s logo shows a stallion
rearing high. The first US filing for this trademark was in 1947. A 1985 trademark filing shows TESA S.a.
and Pierre Roch, S.a.R.L. as joint applicants. Etalon (as well as some tools marked Roch) are now best
known as a TESA brands. TESA itself is now (along with Brown & Sharpe) part of the Hexagon Metrol-
ogy Group.

Item #170
Etalon 0-1” micrometer with a speeder, friction
thimble, lock, and carbide anvils.
The Etalon logo nicely molded into the front pad. Top
quality micrometer with signs of careful use; more a
“user” than “collector” micrometer.

$40 donation

64
Item #171
Etalon
0-1” Microrapid micrometer. Possibly the finest “feel”
of any micrometer made. It has a precisely made
double pitch, double start screw that covers .100” per
revolution; rather than the more customary .025” per
rev. It’s much faster to use; opening and closing 4x
faster (not 2x as suggested below for the metric units).
Here’s what Long Island Indicator (one of the finest
dealers/service companies for precision instruments)
has to say:
“. . . available only in metric: 0-25mm, 25-50mm, 50-75mm,
and 75-100mm. The inch versions were discontinued some
time ago much to the chagrin of many a discerning machin-
ist. The thimble on this metric micrometer has 100 gradua-
tions rather than the standard 50 graduations. Reading this
scale is faster and less prone to error. Plus, you only have to
turn the thimble half as much as the regular micrometer so
the anvils open and close quickly. Hence, “micro-rapid.” For
this tool alone it’s worth switching to metric.”

The new metric units cost over $300. Due to their

scarcity, used English-measure versions often draw
near-new prices. This (English measure!) example is
in excellent mechanical condition with cosmetic signs
of wear.

$130 donation

65
Item #172
Etalon
(Swiss) set of 3 micrometers 0-1, 1-2, and 2-3” All
in very nice condition, with the 2-3” looking new. Et-
alon was/still is considered by many to be the finest
manufacturer of micrometers. Some features of this
mic include a slightly larger (easier to read) thimble,
a smooth friction “ratchet” for repeatable pressure, a
Euro style vernier scale (easier to read), and plastic
pads designed to limit heat transfer and distortion to
the micrometer frame. However, the main feature is
the high quality of the micrometer screw itself. Etalon
micrometers, under the TESA umbrella, are now of a
slightly different design, incorporating a cost-reduced
plastic lock and friction thimble – these “vintage” ones
are arguably made to a slightly higher standard. The
donation price is less than you’d pay for just one of
newer versions ($199 to $339 depending on size).

$180 donation

Item #173
Set of 2 Etalon
(Swiss) micrometers 0-1” and 1-2” Etalon was/is con-
sidered by many to be the finest manufacturer of mi-
crometers. Some features of this mic include a slight-
ly larger (easier to read) thimble, a smooth friction
“ratchet” for repeatable pressure, a Euro style vernier
scale (easier to read), and plastic pads designed to limit
heat transfer and distortion of the micrometer frame.
However, the main feature is the high quality of the mi-
crometer screw itself. Etalon micrometers, under the
TESA umbrella, are now of a slightly different design,
incorporating a cost-reduced plastic friction thimble.

$85 donation

66
Item #174
Etalon 0-1” indicating micrometer with com-
parator dial reading to .0001” and a push button
anvil release.
The comparator as well as the vernier read to .0001”
This is an earlier version of the Etalon comparator,
lacking the adjustable part support seen in later mod-
els.

$60 donation

Item #175
Etalon 0-1” indicating micrometer in box.
Includes a lock, a built-in part support, a .00005”
comparator, an anvil release, and a original fitted box.
These cost well over $1000 new, and draw $400 or so
used at auction. This one is in good cosmetic condi-
tion, but could use a cleaning (congealed oil). This
type is designed for accurate repetitive measurements.
Cool mic.

$250 donation

Item #176
Etalon 0-1” indicating micrometer.
Includes a lock, a built-in part support, a .00005”
comparator, an anvil release, and a original fitted box.
These cost well over $1000 new, and draw $400 or so
used at auction. This one is in average cosmetic condi-
tion and very good operating condition..

$225 donation

67
Federal Products Co.
was founded in 1918. Now part of the Mahr Group and is known as Mahr Federal Inc.

Item #177
Federal 200P 0-1” indicating micrometer in
original black plastic case.
Both the vernier and comparator read to .0001” The
mic is a dull satin chrome, with a lock and anvil release.
Has the original owners name (Dorian Shainin) on the
back and needs a cleaning. The front looks near new
and is marked “Pat. Pending.”

$50 donation

Feinmess Suhl GambH

(Suhl, Germany) was founded as Friedrich Keilpart & Co. in 1878 for the manufacture of calipers and
gages. It was nationalized as Feinmesszeugfabrik Suhl in 1952. By 1970 it was taken over by the VEB
Carl Zeiss Jena conglomerate. It 1992 it became part of August Steinmeyer GmbH & Co. A quality
maker now known as Feinmess Suhl or FMS Suhl.
Item #178
Feinmesszeugfabrik group of three microm-
eters: 75-100mm, 125-150mm, and 175-mm in
original wood boxes.
A very good design with an effective speeder and
ratchet position, locks, carbide faces, thermal pads, etc.
The included standards have an effective alignment
mechanism for ease of use. The large thimbles make
readings easier. All three are in overall good condi-
tion. The clinker in all this was that they came to me
skipping 25mm sizes at a time. The unfinished proj-
ect was to make a 25mm anvil extension so this would
cover the entire range from 75 to 175mm. These likely
date from past 1952 to 1970, but look modern.

$150 donation

68
Flechel & Brown
(Toledo, O.)

Item #179
Flechel & Brown 0-1” micrometer with ratchet,
lock, and decimal equivalents on the frame.
Nicely made, of a standard design seen worldwide. The
maker of this mic appears identical to the maker of the
Fulton (steamship logo) mic noted elsewhere. Identi-
cal ratchet, thimble, lock, and lettering of the decimal
equivalents to that mic. The only difference is that
the Flechel & Brown has a cut-away frame design, de-
signed to let it reach in slightly tighter places.

$30 donation

Fleming Machine Company

(Worcester, Mass) spun off its small tools division as the Fleming Mfg. Company in 1929. The Black
& Decker company history notes B&D as having purchased Fleming Machine Co. (perhaps the other
manufacturing assets) in 1929.
So, consider these micrometers as bridging between the Roaring Twenties(Machine Co.) and the Great
Depression (Manufacturing Co.). I have three sets of their 0-4” interchangeable anvil micrometers; pos-
sibly “cornering the market!?”. The better condition and more valuable ones have the older Fleming Ma-
chine Co. label and pre-date 1929. It appears the company didn’t survive the depression; despite selling
a good quality product. Given some similarities in design, it is thought the micrometers may have been
made by Reed Small Tool Works, which itself struggled to survive and was eventually sold to the Tubular
Micrometer Company.
Item #180
Fleming Machine Co. 0-1” micrometer;
early 20’s? Well worn, but looks to have retained its
accuracy. Send it to a friend from Worcester, Mass?

Donation $15

69
Item #181
Fleming Machine Co. 0-4” interchangeable anvil
micrometer set #1.
This is the best condition and most complete set. It is
one of the older “Machine Co.” examples, predating the
1929 name change. The 2” standard was missing and
has been replaced by its Starrett equivalent.

$100 donation

Item #182
Fleming Machine Co. 0-4” interchangeable anvil
micrometer set #2.
This is a very good condition set, with all its anvils, but
missing the 2” standard and adjustment spanner. It is
one of the older “Machine Co.” examples, predating the
1929 name change.

$70 donation

Item #183
Fleming Machine/Manufacturing Co. 0-3” inter-
changeable anvil micrometer set #3.
This is in a well worn wood box marked “Mfg. Co.”
with a micrometer marked “Machine Co.” The frame
carries a cursive script “Fleming” and also the model
No. 1204. It’s missing the 3-4” anvil, the 2” standard,
and its small wrench.

$35 donation

Item #184
Fleming inside micrometer with rods for the
range 1.5 to 5 inches.
The box is marked Fleming Manufacturing Co. while
the micrometer itself is marked Fleming Machine Co.
and model no. 1225. Good condition, with a bit of
history.

$35 donation

70
Forsberg Mfg. Co.
(Bridgeport, Conn.) was active around 1926 through the 1950’s, was founded by a former employee of
Crescent Tool Co., and made a variety of hand tools. This according to vintagemachinery.org.

Item #185
“THOR” branded 0-1” micrometer with an alu-
minum die cast frame (including a fake lock,
cast in) and a speeder at the end.
Another entry in the low cost made-in-America
sweepstakes

$15 donation

Item #186
“VIKING” branded 1-2” micrometer with an
aluminum die cast frame (including a fake lock,
cast in) and a ratchet at the end.

$15 donation / $25 for the pair of Forsberg mics

Fred V. Fowler Company

(Auburndale, Mass.) is a US distributor of precision tools. In years past, they distributed Helios (Germa-
ny), NSK (Japan) and other micrometers. The company goes back to at least 1973 (their catalog #972).

Item #187
Fowler 0-1” disk micrometer likely made by NSK
in Japan.
Includes ratchet, lock, original wood case,, and original
blue painted frame. Well made, in very good condi-
tion, except for a “Machine Side” marking in the paint
on the rear side (this could easily be touched up). A
useful disk size; not too big, not too small.

$45 donation

71
Item #188
Fowler 0-1” tubing micrometer. Very good con-
dition, but it’s wood case is missing its sliding
lid.
No country of origin is noted; but possibly a Polish im-
port. While no tubing mics appear in the 1973 Fowler
catalog, mics with similar thimbles and thermal pads
(e.g. disc and thread mics) do. At that time, much of
the stock was from Poland. Compare to the Starrett
#569 micrometer for a similar type.

$25 donation

Item #189
Fowler 0-1” and 1-2” mechanical digital mi-
crometers made for them by NSK (Nippon Seiko Ka-
bushik Kaisha, a.k.a. Japan Micrometer Mfg. Co). The
main advantage is faster and easier reading. .0001”
can be read through the vernier. The 1” size is in very
good working condition. The 2” size is new old stock
complete in its original packaging and wooden case.
The quality is comparable to Mitutoyo (excellent) and
indeed the design looks as if some elements had been
“borrowed.” Note that the NSK Japan factory is no lon-
ger making micrometers.
While mechanical digital micrometers have been
largely replaced in industry by electronic digital mi-
crometers, these still have a couple advantages. First,
they’re cool in a clunky geeky way. Second, you’ll nev-
er leave a battery in them only to find years later that it
has leaked and destroyed the micrometer.

$110 donation

Item #190
Fowler Digitrix II 0-1” electronic digital mi-
crometer, made for them by NSK.
This was one of the earlier hand held electronic mi-
crometers (for the earliest, see the Moore & Wright
example). In working condition, once the battery is
inserted. The blue case is in fair condition, the mi-
crometer inside is very good.

$40 donation

72
Item #191
Fowler apprentice machinist’s kit in blue vinyl
case with fitted interior.
Marked “Made in Germany” but includes Fowler
branded quality tools from Germany (e.g. Helios),
the UK (e.g. Rabone Chesterman) and the US. All
in excellent condition. Helios 0-1” micrometer with
friction thimble, all-satin chrome, lever lock, carbide
anvils, and decimal equivalents. Helios 0-6” stainless
steel dial caliper with .001” on the dial and direct read-
ing of mm. U.S.A. 6” combination square and center-
head, plus a depth gage with both rule and pin attach-
ments. Also, a thread gauge, scriber, dividers, center
punch, and satin chrome rule.

$150 donation

W. Fox & Sons

Smethwick, England. The company was formed in 1949 and last filed accounts in 1980. It’s original
manufacturing facility (conveniently located on Brewery St.) is shown in a 1951 photo, just prior to its
demolition. A 1962 photo shows a new facility, also on Brewery St.

Item #192
W. Fox & Sons 0-.5” micrometer.
A couple of these have surfaced for sale; often ascribed
(due to the open thread and measuring wheel look)
as belonging to the late 1800’s. Indeed, it does a bit
like B&S and other mics of that era. In reality this is a
heavy duty micrometer meant for gauging cold rolled
etc. steel. The finger hold and large wheel allow one
hand operation. One might guess this is circa 1950-
1980, given what little is known (above) about the com-
pany. A search for the UK Registered Design 839947
(inscribed on the tool) can be made.

$40 donation

73
Fulton
The first precision tools I’ve seen marked “Fulton” were revolution counters (speed indicators) listed in
a circa 1900 Montgomery & Co. (NY) catalog. Montgomery & Co. was established in 1876, this was
catalog #21, and tools from Brown & Sharpe and Starrett tools from about 1900 appear in within. Ken
Cope (his “Makers of American Tools) says that Fulton was a house brand of Montgomery & Co, itself
located at 125 Fulton St, NYC.
The United Hardware & Tool Corp. (located at 74 Reade St., NY with branches in Boson and Chicago)
1925 catalog features 79 pages of Fulton branded (complete with steamship logo) tools, including the
micrometer type seen below. All Fulton tools were unconditionally guaranteed by United Hardware to
be free from defects.
The Fulton brand appears still later in 1930’s Sears catalogs.
Item #193
Fulton 0-1” micrometer with a ratchet, lock, and
cool steamboat logo (FULTON name stamped
over a steam-driven paddle wheel boat).
It is marked “No. 108 R” See the “Flechel & Brown”
(Toledo, O.) for a micrometer probably made at the
same factory.

$35 donation

Glastonbury Southern Gage

Item #194
Glastonbury Southern Gage (GSG) #16-1/2E
surveillance master.
These are used to check micrometers from 0 to 6” sizes
in ½” increments. New, they’re around $700. Excel-
lent condition with cover and wood base. Start your
own highly precise pyramid scheme.

$100 donation

74
Goodell-Pratt
Goodell-Pratt was formed when William Pratt two- inch sizes. These Micrometers are the same as
bought control of Goodell Bros. in 1899. A vic- the Nos.112R and 20R described in our catalog with
tim of the depression, Goodell-Pratt was merged the following exceptions.
into the Millers Falls Company in 1931. William
Pratt, the president of Goodell-Pratt at the time The lock nut and ratchet mechanism have been
of the merger remained a member of the Millers eliminated and the decimal equivalents are etched
Falls board of directors until his death in 1946. The on the barrel instead of the frame. The savings in
Goodell-Pratt name remained on tools until at least production costs are passed on to you while the in-
part way through WWII; probably due to both the creased production is part of our contribution to
reputation of the Goodell Pratt name (Millers Falls the War Effort.
was new to micrometers) and out of deference to The same high degree of accuracy, fine workman-
board member William Pratt. ship and finish for which Goodell-Pratt Precision
Here’s the wording on a slip of paper enclosed with tools have always been known are faithfully main-
the WWII-era micrometers: tained.

“To help meet the tremendous demand for Mi- GOODELL-PRATT COMPANY, Greenfield, Mass”
crometers required for the Victory Program our History of the company here: http://oldtoolheaven.
entire production of Optical Micrometers has been com/related/goodell-pratt-history.htm
concentrated on the No.112R and No. 20, one- to

Item #195
Goodell-Pratt
0-1” micrometer. Rare early 1900’s style tool, distin-
guished by a unique spindle locking mechanism.

$35 donation

Item #196
Goodell-Pratt 0-1” micrometer with speeder,
lock, all steel frame.
Decimal equivalents on the spindle. Marked with a T
on the reverse side.

$25 donation

75
Item #197
Goodell-Pratt 1-2” micrometer, all steel finish,
with plain frame, and the old style Goodell-Pratt
spindle lock.
This might possibly be WWII production, saving the
time of adding decimal equivalents. Very good condi-
tion.

Donation $25

Item #198
Goodell-Pratt 1-2” micrometer, all steel finish,
with decimal equivalents on the frame, and the
old style Goodell-Pratt spindle lock.
Apart from the decimal equivalents, identical to the
micrometer above. Very good condition.

Donation $30

Item #199
Goodell-Pratt 0-3” interchangeable anvil mi-
crometer, with one anvil.
This has owners’ markings (possible to polish out) and
a loose lock. It would be useful, though, as a pair to
the Goodell-Pratt 3-6” interchangeable anvil microm-
eter and its anvils (below); covering a range from 0-6
inches.

$12 donation

76
Item #200
Goodell-Pratt
3-6” interchangeable anvil micrometer (comes with
three different anvils to cover the 3-6” range). This
is an early 1900’s style tool, distinguished by a unique
spindle locking mechanism. While thoroughly us-
able and accurate, this is as much of a collector’s item.
The company was formed when William Pratt bought
control of Goodell Bros. in 1899 and was for years a
maker to high quality tools. A victim of the depres-
sion, Goodell-Pratt was merged into the Millers Falls
Company in 1931; though the Goodell-Pratt brand re-
mained on tools for a decade or so after.

$85 donation

Greenfield Tap & Die (GTD)

was founded in 1912 and is now part of Kennametal. It did not make micrometers (though it did buy
Wells Brothers, maker of a unique thread micrometer). That said, one of their gages is included to pro-
vide background for the Slocomb and Mitutoyo double spindle micrometers.

Item #201
GTD “Go/No-Go” gage.
The anvils are adjusted to the high limit and low limit
of a part; and were used for in-process gauging.

HDT International
(Paramount, CA) is a supplier of Chinese-made gage blocks, micrometers, etc.

Item #202
HDT 0-1” indicating micrometer with a non-re-
sponsive comparator.
The more pointed comparison is between this unit
(about $160 new) and higher quality units (about $500
new). From the outside, this looks like an acceptable
quality mic. From the inside?? Might be fun to try
to repair – better entertainment than a reality show.
More likely a cautionary tale.

$20 object lesson

77
Helios Messtechnik GmbH & co. KG
(Germany) was founded by Wilhelm Schneider in 1910 as a “factory for measuring instruments.” In
1920 Otto Kern joined the company and it was named “Schneider & Kern.” In 1973 it became a wholly
subsidiary of Mayer & Cie and became known as Helios Messtechnik. It was later acquired by the Mahr
Group of Goettingen, Germany in 2006. Overall a good quality maker. The friction thimble design of
some of its micrometers is particularly effective.
Item #203
Helios 0-1” micrometer with satin chrome
frame, ratchet, lock, and .0001” vernier.
Includes decimal equivalents on the thimble and a
cardboard box. Excellent condition.

$30 donation

Item #204
Helios 0-1” micrometer with satin chrome
frame, ratchet, lock, and .0001” vernier.
Includes decimal equivalents on the thimble, carbide
anvils, thermal pads, and a Helios-marked fitted wood
box. A step up in features from the other example. Ex-
cellent condition.

$40 donation

Item #205
Helios / Fowler 0-1” micrometer with satin
chrome frame, friction thimble, lock, and .0001”
vernier.
Complete with original brown soft case, mint condi-
tion, and a good match for the micrometer below.

$35 donation.

Item #206
Helios 1-2” micrometer, also marked with the
Fowler (US distributor) logo.
Friction thimble, lock, carbide anvils, and .0001” verni-
er. All satin chrome with decimal equivalents on ther-
mal pads affixed to the frame. Complete with original
brown soft case. Mint condition.

$40 donation

78
Henry L. Hanson
(Worcester, Mass); with once source indicating a 1937 trademark registration for the Ace brand. Better
known as a maker of taps and dies sold through a variety of consumer-oriented hardware stores. Sears
Roebuck sold a “Fulton” branded micrometer of identical design to Hanson’s mics.
Item #207
Ace 0-1” micrometer with aluminum die cast
frame and friction/speeder.
Low cost mic sold non-professional channels.

$10 donation

Item #208
Ace 0-1” micrometer with a chrome plate over an
aluminum die cast frame and a friction/speeder.
This one has decimal equivalents stamped into the
thimble and would have been slightly costlier to make.

$12 donation

H&Hip
is a brand affixed to Chinese import tools; usually of fairly good manufacture.
Item #209
H&Hip 0-.5+” conventional micrometer
new in original packaging. A useful quality compari-
son to several decades of earlier small/inexpensive mi-
crometers.

$15 Donation

Item #210
H&Hip 0-1/2” rapid acting (.050 per revolution)
micrometer with speeder and large friction
thimble that reads directly to .0005 in.
Surprisingly good micrometer for the price (another
was disassembled to see). This opens and closes at
twice the rate of a typical micrometer (while the Etalon
MicroRapid is at four times the rate). New in box.

$45 donation

79
Hilger & Watts
Item #210.1
Hilger & Watts (England) clinometer
Able to read (through the tiny “telescope”) angles to
about 5 second accuracy. The base can be leveled to
zero by placing it on an extremely flat surface and ad-
justing the base knob until it reads zero when reversed
exactly in place. Fairly hard to find – the only seller of
one I could find wants $2100 for theirs.

$40 Donation

Hommell Werke
Hermann Hommel founded his workshop in 1876 and, according to one source, began making precision
measuring tools in Idar-Oberstein by 1893. Along the way it made a number of incredible machines
(e.g. http://www.lathes.co.uk/hommel/) and a number of micrometers. The company apparently liked
a sort of mottled paint job unique to it – it appeared on machines (dating to the 1930’s) and many of its
micrometers. The company was take over by Thyssen AG in 1990 and demerged in 1997 (management
buy out). As of 2000 it became part of Jenoptik’s metrology business.
Item #211
Hommelwerke 0-1” mechanical digital microm-
eter with friction thimble/speeder.
An uncommon example in good working condition.
Has a manufacturer’s engraving of 10705 on the reverse
side of the thimble and a plaque proclaiming patents in
Germany, the USA, Switzerland, France, and Italy. The
wood case is embossed with the Hommell logo, but
also has a Hartmetall (sintered carbide?) label.

$40 Donation

Item #212
Hommelwerke 0-1” mechanical digital microm-
eter with friction thimble/speeder.
A second example of an uncommon mic. Includes a
lock and carbide anvils, with the paint in fairly good
condition. A plaque on the reverse side proclaims pat-
ents in Germany, the USA, Switzerland, France, and
Italy.

$40 donation

80
Item #213
Hommelwerke 0-25mm micrometer.
Well made with a push button to lock the spindle, a
large ratchet, and the usual mottled finish. The paint
is mostly worn, the chrome and working parts are very
good.

$30 donation

F. W. Horstmann Co.
(Irvington, NJ) were makers of a patented (beginning in 1919 by Frederick W. Horstmann) indicating
caliper.

Item #214
F. W. Horstmann patent indicating caliper.
This would be set to the desired dimension, with the
indicator reading .0001” divisions under and over. A
forerunner of the indicating micrometer.

$45 donation

International Tool Co.

(San Leandro, CA)
Item #215
International Tool Co. inside micrometer set
with measuring rods for 3” – 12” range.
Comes in a heavy black thermoplastic case, in good
condition.

$35 donation

81
C. E. Johansson AB
(Eskilstuna, Sweden) was founded by Carl Edvard Johansson in 1911. Also known as CEJ. Prior to that
time (1890’s) he invented and perfected the gage block (“Jo block”) system – a major breakthrough in
precision measurement. The process of manufacture was a trade secret for many years. An American
company (Poughkeepsie, NY) was formed around 1918 and later sold and moved to the Ford Motor Co.
See also the Swedish Gage Co. entry. The Swedish company (CE Johansson AB) is now part of the me-
trology conglomerate, Hexagon Engineering.

Item #216
C. E. Johansson -- CEJ – 0-1” micrometer.
From the inventor of gage blocks. See, also, the en-
try for the Swedish Gage Co. The square frame allows
deeper measurements on rectilinear parts near the full
1” size.

$25 donation
Item #217
C. E. Johansson 0-1” micrometer
#M 106 E with ratchet, lock, satin chrome, decimal
equivalents, and blond (it is a Swede) wood case. Sold
through Sears Roebuck of all folks, with circa 1958 pa-
perwork.

$30 donation

Item #218
C. E. Johansson (CEJ) #117 disk micrometer with
0-20mm range.
The flat anvils extend the normal range of use to soft-
er materials and some tight spaces. Includes friction
thimble, lock, and original red/black molded case.
Very good condition.

$45

Item #219
C. E. Johansson (CEJ) #103E micrometer 1-2” in
original wood box.
Includes friction / speeder, lock, and decimal equiva-
lents on the frame Would pair nicely with a 0-1” CEJ
mic.

$30 donation

82
Item #220
C. E. Johansson wire micrometer #M92E with
0 - .5” capacity, .0001” vernier, friction thimble,
and original wood case.
Meant for easily measuring wires, pins, etc. but will
accommodate many other parts. Nicely made small
micrometer in excellent condition.

$50 donation

Kalibr
(Moscow) is a large plant, founded in 1932, to make micrometers and other precision tools. The one
example I have of an early micrometer looks to have largely borrowed a Starrett design. More recent
examples (cold war era) have a heavy (heroic?!) style.

Item #221
Kalibr 0-25mm micrometer.
Perhaps from the 1930’s or 40’s when Stalin was con-
solidating power and establishing state industries? Of
standard design; looking much like an early 1900’s
Starrett design (the front lock etc.). Marked with what
is likely a model number (1933r, with the r likely for
the year of manufacture -- or possibly for ratchet) and
a No. 21898. It is marked only with a K and a reversed
N; which is KU in the Cyrillic alphabet. Nicely made;
showing how the same basic design was duplicated
by many manufacturers.” A different Kalibr logo is
engraved on all other micrometers in this collection
(which are also of much heavier construction); but the
same KU logo is embossed in one wood box.

$45 donation.

Item #222
Kalibr 0-25mm micrometer with satin chrome,
lock, and ratchet.
Heavy duty! In wood box embossed with a KU (re-
versed N) logo.

$40 donation

83
Item #223
Kalibr 0-25mm black wrinkle frame micrometer
with ratchet and lock.
Marked “USSR” and 1979r. Fitted plastic box. Mint
condition.

$35 donation

Item #224
Kalibr 0-25mm gray painted frame micrometer
with ratchet and lock.
Marked “USSR” and numbered 7419. Comes with
original paperwork, dated 1991, and fitted plastic case.
Mint condition.

$40 donation

Item #225
Kalibr (Russian) 0-25mm thread micrometer
with 9 pairs of anvils in a fitted gray plastic case.
Includes friction “ratchet” and lock. A Cyrillic inscrip-
tion on the thimble and case, but otherwise excellent.
The anvils will fit many other thread mics, including
a slightly loose (by maybe .01mm) fit to Mitutoyo. A
very good quality Cold War era thread mic, at a frac-
tion of replacement cost.

$95 donation

Item #226
Kalibr 0-100 mm depth micrometer, reading
in .01mm, with four rods and both calibration
standards.
The usual robust Russian construction, from the depths
of the Cold War. Near new condition. If you don’t
want to measure (which it’s fully qualified to do), af-
fix your commissar’s rubber stamp to the bottom in a
warning, address, or ?? message of your choice.

$50 donation

84
Item #227
Kalibr (USSR)
A robust set of four Cold-War era Russian metric mi-
crometers. While of heavier construction than most of
their worldwide counterparts (companies like Starrett
asked that customers pay extra for the heavy frames),
these are nicely made with carbide anvils, a large (easy
to read) thimble, locks, and a good ratchet. Keep a set
in your bomb shelter, to help restart civilization as we
know it??

$180 donation for the set

Keilpart
(Germany) is the predecessor company of Feinmess Suhl. Here’s one of their micrometers and its case:
Item #228
Keilpart micrometer and case
Unknown origin

not part of the collection

K. K. System
(Germany) – a maker of watchmaker’s gages.
Item #229
K.K. System 0-8mm wire micrometer.
Overall cylinder-like form designed so it is easy to lay a
wire or pin between the anvils.

$30 donation

85
Kukenis
– likely a highly skilled toolmaker, but possibly part of a short run.

Item #230
Kukenis 0-1” thread micrometer?
This is a beautifully made micrometer, using a mid 20th
century Brown & Sharpe spindle for its thread. The
knife-edge anvils were likely for measuring threads. A
testament to machining skills and the notion of mak-
ing one’s own tools.

$55 donation

Kroeplin GmbH
(Germany) was founded by Henrich Carl Kroeplin (a master watchmaker) in 1883. The company now
makes a series of quick reading gages, including the “Quicktest.” The Dyer Company (Lancaster, PA) is
one of their US distributors.

Item #231
Dyer/Kroeplin Schnelltaster (!) 0-1” by .0025. T
his is a quick reading instrument with a deep (16”)
throat for getting to various points inside large sheets.
While used in industry, it is prized by musical instru-
ment makers and others who need to know the thick-
ness of wood sounding boards and the like. The wood-
en case bears Dyer’s model #334-005.

$135 donation

86
Item #232
Dyer/Kroeplin deep reach (over 6” x 6”) gage
with dial thickness readings 0 to .4” by .001.
This type of gage is suited to situations where a thick-
ness must be measured over an obstruction, such as a
flange. It is also used by stringed instrument makers to
measure through the center hole. The long spindle is
removable with just a twist to better access the measur-
ing point. Comes in a large wood Dyer case marked
Model #363-000 (US 066K) with a Kroeplin-made
Quicktest indicating mechanism. Like new except for
quality control number; which a quick blast of black
wrinkle spray paint could deal with. Be the first kid on
your block to have one of these – or better yet find a
grateful guitar maker.

$120 donation

L..
is a USSR maker. The logo (three Cyrillic letters within a diamond) would sound somewhat like el ee eh
when pronounced (based on my dim recollection of high school Russian).

Item #233
L.. 0-25mm indicating micrometer with push
button anvil release; reading to 2 micrometers.
Precise micrometer in excellent condition. Includes
original case and adjustment spanner. I don’t know
the history of the maker, but the longer inscription on
the comparator dial translates to “Made in the USSR.”

$120 donation

87
Item #234
?? Russian-made
50-75mm indicating micrometer. Similar to the above
indicator micrometer, but with the anvil release reposi-
tioned. Same adjustment wrench, dial, etc. Includes
a still-wrapped 50mm standard. Excellent condition,
with the exception that the foam was removed from
the case. Like Mitutoyo, the Russians were a victim of
foam rot. Left alone, the foam gradually turns to a cor-
rosive goo. Caught this one in time; other than the
case interior it’s near new.
The graphic logotype in the center of the comparator
shows two errors “measuring” a Mobius strip look-
ing bit. The case is marked (in Cyrillic) “Micrometer
Model 02202.”

$120 donation

Chas. Lowinson
(NYC) was the sole agent of a thread count micrometer manufactured by the Chronik Brothers, also of NY.
Earlier versions of this were patented by A. Chronik on Oct. 20, 1908 and Sept. 20, 1910 (Pat.#970,795)
and remain essentially in its original form (despite a “refresh” of the patent in 1929).

Item #235
Lowinson thread count micrometer.
You know those sheets or garments that claim 400
threads per inch? This instrument, somewhat te-
diously, tells the true story. This is engraved with a
later patent number (#1740970) dating from Dec. 24,
1929. Near mint condition in case, with paperwork.

$70 donation

88
The Lufkin Rule Co.
The Lufkin Rule Co. (Cleveland, Ohio and later the means of adjustment.
Small Tools Division, Saginaw, Mich.) was founded
by Edward Taylor Lufkin in 1869. Lufkin, born Feb. The depression years were difficult for Lufkin, while
1948, enlisted at the age of 16 (Mar. 1864) with the business for precision tools rebounded during
Ohio Volunteers in the Civil War. World War II.

Shortly after serving in the war, he founded the E.T. Precision small tool manufacturing was discontin-
Lufkin Board and Log Rule Manufacturing Co. at ued by Lufkin in 1966. The business was bought
age 21. About fifteen years later, between 1883- in November 1966 and briefly run by the Pratt &
1885, investors bought out his interests and named Whitney Machine Tools Div. (Hartford, Conn.) of
it The Lufkin Rule Co. Around 1890 the company Colt Industries. Both Lufkin and Pratt & Whitney
introduced the first flexible steel tape to the US. struggled for distribution in a market dominated by
Brown & Sharpe and Starrett. Lufkin itself (measur-
The company began manufacturing micrometers ing tapes, etc.) was bought by Cooper Industries in
and other precision hand tools beginning in 1919. 1967.
My earliest Lufkin Small Tools catalog (#2) shows
seven pages of similar-looking all steel microm- The older Lufkin micrometers, with the smaller di-
eters with an August 1, 1922 patent date. Many ameter thimbles, have a similar feel to the very com-
later Lufkin micrometers are marked with pat- mon Starrett 436 series. Lufkin’s micrometers from
ent numbers #1,568.296, issued January 5, 1926; later years, with the larger satin-chrome thimbles,
#1,940,475, issued in 1933; and #2,212,910, issued are among my favorites and several examples have
in 1940. The 1926 patent is for a roller type spindle been acquired. Despite being discontinued 40
lock and the 1933 and 1940 patents both relate to years ago, these have excellent quality and feel.

Item #236
No. 9A Lufkin height gage attachment in origi-
nal cardboard box and No. 680B Lufkin inside
micrometer set in original fitted wood case.
The inside micrometer set measures from 1.5 to 12”
and includes a handle for ease of handling in deeper
spaces. The #9A attachment converts the inside mi-
crometer set to a height gage. Note the subtle colors
from hardening and tempering this gage. Very good
condition on both.

$75 donation for the pair of #9A and #680B

89
Item #237
No. 111 Lufkin “Millmens” 0-1” micrometer
with original vinyl pouch, cardboard box and
paperwork.
Heavy satin chrome frame with decimal equivalents on
the front and 1940 patent number on back. This mi-
crometer was designed to handle rough use in a steel
mill; but looks to have had a relatively easy life.

$30 donation

Item #238
No. 111 Lufkin “Millmens” 0-1” micrometer
with original cardboard box and paperwork.
Heavy satin chrome frame with decimal equivalents on
the front and 1940 patent number on back. This mi-
crometer was designed to handle rough use in a steel
mill; but looks to be unused.

$40 donation

Item #239
No. 121 H Lufkin heavy steel mill micrometer
with a large thumb lock, provision for a handle
at the base of the frame, and large numbers for
reading at a distance.
Meant for measuring even if it was hot steel coming off
a line. Fine for plain cool measurements as well. This
one is in used condition, with no extraneous engrav-
ings.

$40 donation

Item #240
No. 121 H Lufkin heavy steel mill micrometer
with a large thumb lock, provision for a handle
at the base of the frame, and large numbers for
reading at a distance.
Meant for measuring even if it was hot steel coming off
a line. Fine for plain cool measurements as well. This
one is in very good condition.

$55 donation

90
Item #241
No. 822 H Lufkin 1-2” mill micrometer.
This is an earlier version of the Millmens micrometer
with the provision for a handle and large numbers; but
a smaller diameter spindle and Lufkin’s regular painted
frame (with ribs) at the time. Includes Lufkin’s 1940
patent number and looks to have seen a lot of use.
Handle is not original.

$25 donation

Item #242
No. 901A Lufkin Master Planer Gage with all its
accessories in an original fitted wood case.
Carries patent #2694861. The gage can be used in any
position and has a range from about 0” on the zig zag
scriber to about 10” using the various adapters and
the tall size up. Planer gages are used to set precise
heights; originally for metal planers and shapers but
now for a variety of purposes. Every major precision
tool maker carried these, often in two levels of qual-
ity (this is the wider, higher quality unit that is directly
comparable to Starrett #995). I picked Lufkin (among
B&S, Helios, Starrett, and others) to join COFES, just
for a bit of Lufkin nostalgia. Precisely made tool in
excellent condition.

$100 donation

Item #243
No 1610M Lufkin Rule Co. 0-13mm micrometer
in all satin chrome with a ratchet and 1940 pat-
ent number on back side.
Near mint condition micrometer in a small size.

$45 donation

91
Item #244
No. 1621 Lufkin 0-1” all satin chrome microm-
eter in older style (smaller diameter thimble)
with 1940 patent number on back.
Includes a knurled roll type lock and decimal equiva-
lents. Excellent condition in original cardboard box.

$30 donation

Item #245
No. 1641 Lufkin Rule Co. 0-1” micrometer with
an Aug. 1, 1922 patent date on the back.
Includes ratchet, lock, and decimal equivalents
stamped into the frame. These sold for $10 in the mid
20’s – about $108 today. Nice shape.

$30 donation

Item #246
No. 1641 Lufkin Rule Co. 0-1” micrometer with
an Aug. 1, 1922 patent date on the back.
Includes ratchet, lock, and decimal equivalents
stamped into the frame – identical to the micrometer
above, with a rougher action to the ratchet.

$25 donation

Item #247
No 1641 Lufkin 0-1” micrometer with all satin
frame and newer style (larger) thimble with
ratchet at end.
Includes lever lock, decimal equivalents, and a black
Lufkin case. Very good condition, with Lufkin’s 1940
patent number engraved on thimble.

$35 donation

92
Item #248
No. 1641V Lufkin 0-1” micrometer with all satin
frame; similar to above but with a roller lock
rather than lever lock; the addition of a .0001
vernier; and the 1940 patent number is located
on the end of the thimble.
Has decimal equivalents and the large ratchet on the
end of the thimble. Very good condition in original
cardboard box with paperwork and spanner. Likely
mid 1950’s build date.

$40 donation

Item #249
No. CT1641 Lufkin 0-1” micrometer.
Mint condition in original vinyl pouch and cardboard
box. All satin chrome, ratchet at end of thimble, car-
bide tips, and decimal equivalents. Beautiful microm-
eter.

$45 donation

Item #250
No CT1642V Lufkin 1-2” micrometer.
A series mate to the Lufkin CT1641 micrometer, but
with a .0001” vernier and in average rather than mint
condition. No non-original markings. Includes a black
Lufkin case.

$20 donation

Item #251
No. CT1641V Lufkin micrometer.
As above, with the addition of vernier markings. Slows
slight signs of use. Nice mic.

$40 donation

93
Item #252
No. 1661V CT 0-1” and No. 1662 1-2” Lufkin mi-
crometers sold as a set.
These are mint condition micrometers with dull
chrome finishes all over, lever locks, friction thimbles
with a fixed portion at the end, and decimal equiva-
lents stamped into the frames. The 0-1” is in its origi-
nal cardboard box and has carbide anvils and a .0001”
vernier. The 1-2” is in its black leatherette box and
includes a Lufkin Rule Co. standard (1” diameter). Re-
ally nice pair.

$100 donation for the pair

Item #253
No. 1661V 0-1” and No. 1962V 1-2” Lufkin mi-
crometers sold as a set.
These are in near mint condition in original cardboard
boxes. Both have satin chrome friction thimbles with
a fixed portion at the end, lever locks, and a 1940 pat-
ent number marked on the thimble. The 0-1” is all-
satin chrome with decimal equivalents. The 1-2” has a
black wrinkle finish frame.

$90 donation for the pair

Item #254
No. CT1661V Pratt & Whitney 0-1” micrometer
with .0001 inch vernier (the “V” in the model)
and carbide tipped (the “CT).
Satin chrome with friction thimble and decimal equiv-
alents. Identical the Lufkin #1661V micrometers of
later vintage. This one has a previous owner’s markings
lightly affixed. Good working condition.

$15 donation

94
Item #255
No. 1811 Lufkin Rule Co. 0-1” micrometer with
satin chrome thimble and green wrinkle finish
frame with stiffening ribs.
1940 patent number. Excellent condition with original
box and paperwork. This looks to have been sitting
in its box for most of 50-70 years; with a slightly stiff
thimble from congealed oil – easily replaced.

$30 donation

Item #256
Nos. 1841 (0-1”), 1822 (1-2”), and 1823 (2-3”)
Lufkin Rule Co. micrometers.
These are all of the same design, with steel thimbles,
roller type locks, painted frames with the older style
ribs, and 1922 and 1926 patent dates stamped on the
back. A set of three earlier Lufkin micrometers. In
good condition for their age, and still accurate.

$85 donation

Item #257
Nos. 1822 (1-2”) and 1823 (2-3”) Lufkin Rule Co.
micrometers.
Similar to the above #1822 and #1823 micrometers but
with a more recent satin chromed thimble and a 1940
patent number stamped on the back. Paint wear, but
otherwise good condition.

$50 donation

Item #258
No. 1911 Lufkin 0-1” micrometer with satin
chrome thimble and dark green frame.
Has 1933 and 1940 patent numbers on the back. Good
condition, with minor paint wear, in Lufkin black vel-
vet-lined case.

$30 donation

95
Item #259
No. 1911 Lufkin 0-1” micrometer with 1940 pat-
ent number noted on the larger (newer) style
satin chrome thimble.
Black wrinkle frame; good condition.

$20 donation

Item #260
No. 1911C Lufkin Rule Co. 0-1” point microm-
eter for use as a thread comparator and reaching
into grooves and other tight spaces.
Marked with 1933 and 1940 patent numbers on the
back.

$25 donation

Item #261
No. 1913 (2-3”) and No. 1914 (3-4”) Lufkin Rule
Co. micrometers.
Plain steel thimbles, painted frames, with 1933 and
1940 patent numbers stamped on the back. Back side
raised pad on each has a tracking number, otherwise
good. Possibly a good way to extend a 0-2” set.

$40 donation

Item #262
No. 1941 Lufkin Rule Co. 0-1” micrometer with
older style (smaller diameter) thimble in origi-
nal wood box.
Steel finish thimble, conventional ratchet, roller lock,
and enameled frame. Includes 1926, 1933, and 1940
patent numbers. Very good condition.

$35 donation

96
Item #263
Nos. 1941 (0-1”) and 1942 (1-2”) Lufkin microm-
eters with steel thimbles, ratchets, and roller
type locks.
Rounded style painted frames. The 0-1” has 1926,
1933, and 1940 patent numbers stamped, plus a re-
painted frame. The 1-2” has the same design but ear-
lier manufacture, with 1922, 1926, and 1933 patent
numbers.

$35 donation

Item #264
No. 1941 Lufkin 0-1” micrometer with large
ratchet at end of satin chrome thimble.
Includes lever lock and black wrinkle frame. Includes
original wood box (marked) with a near mint mic in-
side.

$35 donation

Item #265
Nos. 1941 (0-1”) and 1942 (1-2”) Lufkin mi-
crometers with large satin chrome thimbles (de-
sirable newer style) and wrinkle black frames.
Both include a large diameter ratchet at the end of the
thimble and a lever lock. Very good condition.

$85 donation

Item #266
Nos. 1942 (1-2”) and 1943 (2-3”) Lufkin Rule
Co. micrometers.
Steel finish thimbles with roller locks and conventional
painted frames with 1933 and 1940 patent numbers
stamped on the rear pad. Some signs of wear, but no
markings and overall good condition. Add a 0-1” mic
to complete a small set?

$45 donation

97
Item #267
No. 1961 Lufkin 0-1” micrometer in worn condi-
tion.
Similar micrometer as the Pratt & Whitney model No.
1961 below; but this one has a roller type lock and has
seen significant use.

$10 donation

Item #268
Lufkin 0-4” interchangeable anvil micrometer
set,
complete and near mint condition in a wood case.
Patent number 2,212,910; which was issued in 1940.
Likely of WWII or slightly later manufacture.

$75 donation

Item #269
No. 2630 Lufkin 0-1/2” ball anvil micrometer in
all chrome with decimal equivalents and 1940
patent number on back side.
Cut-away frame allows tubing measurements. No
non-original markings, but mic needs calibration and
chrome is worn.

$15 donation

LX
is the sole marking on speed indicators made by Manufacturer’s Belt Hook Co. of Chicago, Illinois; be-
ginning around 1920.

Item #270
$10 donation

98
Mahr
(Carl Mahr, Esslingen, Germany). Founded in 1861 and one of the world’s finest makers of precision
tools. The Mahr Group is still focused on metrology, with main locations in Germany (Gottingen, Es-
slingen, and Jena), the Czech Republic (Probostov), the US (with Mahr/Federal in Providence, RI), and
China (Souzhou). The US operations are known as Mahr Federal. Mahr also acquired SIP and Helios
Messtechnik (in 2006). The company’s analog micrometers are beautifully made and they are also known
for indicating micrometers using their own high precision indicators (Millimess, etc.). The merger with
Federal Products in 1999 added to its presence in the US. In general, the current line of micrometers is
priced at the very top range; somewhat limiting sales.
Item #271
Mahr 0-25mm micrometer with extra large (easy
read) thimble, satin chrome, a ratchet, lock, and
fitted wood case.
Excellent micrometer in like new condition. This is a
$300+ micrometer priced new (measurementdepot.
com).

$80 donation

Item #272
Mahr 0-20mm disc micrometer with satin
chrome, ratchet, lock, and fitted wood case.
The large flat anvils are handy for soft materials and
reaching such details as gear teeth. A very well made
micrometer, with a company marking (Design Insight)
and another below that. This is a $400+ micrometer
(measurementdepo.com) if bought new.

$70 donation

Item #273
Mahr 0-1” indicating micrometer #40SF with a
.0001” indicator, anvil release, and fitted wood
case.
The indicator can probably be interpolated to 50 mil-
lionths. Older style micrometer with signs of some
wear, but fully operational. The pushbutton retracts
the anvil for repeat measurements. Probably a $1000
micrometer if still made. Would look and work great
if paired to a micrometer stand and the bit of chipped
black paint touched up.

$70 donation

99
Item #274
Mahr 0-1” bench micrometer with Millimess
fully jeweled dial comparator and fitted wood
case.
Extra large thimble. Very good cosmetic condition,
and in need of calibration. Has adjustable platform
and small diameter anvils for measuring small parts.
Additional types of anvils are available from Mahr.

$125 donation

Item #275
Mahr 0-1” and 0-25mm thread micrometers
(two fitted wooden boxes).
These are being grouped together because the thread
measuring anvils can be shared between both mics (use
the Mitutoyo thread anvils as a guide to US and metric
equivalents – basically the larger the thread pitch the
large the “point” and “V” pair). Both mics are in excel-
lent condition and cost a bit over $500 each new ($1000
total).

$110 donation for the pair

Item #276
Mahr 0-1” indicating micrometer of exceptional
accuracy.
This comes with a Supramess comparator graduated in
20 millionths of an inch, an anvil release, and a lock; all
in the original black fitted wooden case. The compara-
tor has a small knurled knob which is used to adjust the
comparator to zero. This is in excellent cosmetic and
operating condition – and was very costly when still
manufactured. Note: should the indicator become
slightly sticky through storage, it can likely be restored
by pressing the anvil release a few times. It works fine
at the present writing.

$160 donation.

100
Item #277
Mahr 2-4” indicating micrometer with Millimess
.00005” fully jeweled dial comparator.
Used but fully operational. Lightly marked “SPECO
#3” by the original owner. The anvil adjusts to cover
2-3” or 3-4” and can also be retracted (lever arm) for
ease of measurement. A new Millimess dial compara-
tor, alone, is about $200.

$60 donation

C & E Marshall Co.

Item #278
Watch-Craft 0-15mm bench micrometer made
by C & E Marshall Co.
Nice mic with an adjustable parts platform and a fric-
tion thimble reading directly in .01mm. Calibration is
through loosening the screw at the end of the thimble.

$60 donation

Louis Marx and Company

(New York City) was founded in 1919 and made die cast and other toys until 1978. The company was
wildly successful, even through the Depression, up through 50’s – when it was the largest toy company
in the world.

Item #279
Marx toy micrometer #1 0 - .5” Marx toy mi-
crometer #2 0 - .5”
There’s something to be said for a culture where min-
iature tools – including micrometers – are kids toys.
Today the toys are sought by collectors.

$12 donation each

101
Massachusetts Tool Co.
The company was an early (now antique) offshoot of Goodell-Pratt.

Item #280
Massachusetts Tool Co. (Greenfield, Mass.)
0-1”micrometer with a patent date of Feb. 20,
1884 and 0-3” interchangeable anvil microm-
eter,
likely dating from 1910 to the 1920’s but having the
same general design as the 1884 patent.
The same design micrometers, including the same gen-
tly curved spindle and the unique locking mechanism
(cool), were later sold under the Goodell-Pratt name
(see the Goodell-Pratt 6” interchangeable anvil mi-
crometer for comparison). This interchangeable anvil
mic comes with only one anvil, for the 1-2” size. I’ve
included a standard, and it is spot on.

$80 donation (two micrometers)

Massi
Item #281
Massi 0-20mm micrometer stamped “Gehärtet”
(German for “hardened”) on the frame along
with the Massi logo.
This mimics an older exposed thread style micrometer.
However, that type was frequently exported in the 50’s
and later as a low cost option to sell into watchmaking
etc. channels. This is a bit better made than some of
those; but almost surely of that genre. Looks to be rea-
sonably accurate.

$25 donation

102
Mauser Werke
Yep, same as the famed German arms manufacturer, beginning around 1870. It’s not entirely clear (to
me) when micrometer production began. Some suggest this was just after WWI as the company dealt
restrictions on arms manufacture and aimed to diversify amidst economic challenges. Others point to a
period of time around (just before, during, or after) WWII. Today, Mauser tools end up being collected
by both precision tool and arms enthusiasts. As far as I can tell Mauser’s precision tools business was
first sold to Roch and eventually Hexagon. The Mauser micrometer designs, while beautifully executed,
haven’t shown up under other brand names to the best of my knowledge.

Item #282
Mauser 0-25mm micrometer
with an unusual collar fixed around the thimble. Prob-
ably the earliest of all the Mauser mics on display.

$30 donation

Item #283
Mauser 0-25mm micrometer with robust wrin-
kle black frame, lock, and ratchet.
Nicely made, with no particularly unique features. The
Mauser logo cast in relief into the frame is a nice touch.
This appears to be an earlier micrometer.

$50 donation

Item #284
Mauser 0-25mm micrometer, green enamel,
with lock and ratchet.
Beautifully made. Almost surely post 1950 and per-
haps even as late as 1980’s.

$50 donation

103
Item #285
Mauser 0-25mm bench micrometer, fitted with a
.001mm reading dial indicator.
This has the same mechanical digital mechanism as
the 1-2” Mauser example, but with no need of a fric-
tion thimble. Measurement pressure is controlled by
a spring mechanism in the anvil. Bench micrometers
are meant for precision measurements and compari-
son – typically an order of magnitude finer than hand
held micrometers. These has an adjustable platform to
hold parts between the anvils, a retracting anvil, and an
indicator. The part is measured until “0” appears. Re-
petitive measurements and use the plus/minus .001mm
indications on the dial.
It isn’t clear what brand comparator was originally fit-
ted to this micrometer; likely Swiss or German rather
Mitutoyo. However the high precision indicator in-
cluded is alone worth $200 (.001mm = .0000394”).
You might also consider acquiring the other Mauser
mechanical digital indicator along with this (or at least
take a picture), to better prove its Mauser provenance.

$190 donation

Item #286
Mauser 1-2” mechanical digital micrometer.
Probably uneconomical to produce, but a fine example
of German engineering. Compare the (near identical)
mechanical digital thimble with the Mauser 0-25mm
bench micrometer also on view. This same mechanical
digital mechanism has also appeared on micrometers
under the German “MZB” brand.

$70 donation

MG
--see Central Tool Company

104
Millers Falls Co.
Miller Falls Co. (Greenfield, Mass) was a long-time Note the lack of a lock and decimal equivalents:
supplier of tools, founded in 1868. 1n 1931, near
the beginning of the depression, it acquired the Millers Falls also acquired the Union Tool Co. in
Goodell-Pratt Co. including its lines of precision 1957. For more history: http://www.oldtoolheaven.
tools, and its large Greenfield, Mass plant – where com/history/history10.htm
Millers Falls subsequently moved its headquar- One Millers Falls micrometer design of ergonomic
ters. The Goodell-Pratt name and their designs note includes a small (and thus fast) knurled speed-
remained on many Millers Falls tools for a decade er on the end of the thimble with a ratchet wheel
or so more. Indeed, the Millers Falls micrometers just inside it. This was a convenient arrangement
were likely made on the same Goodell-Pratt equip- and makes the old mics still nice to use if they are in
ment and with many of the same employees for a good condition. This design is, I think, one of those
period of time. that make an ideal gift to a mechanically inclined
During WWII, shortages of material and manpower student. It’s good enough to be useful day in and
forced the suspension of some tools. However, out. Given that most of these micrometers were
micrometers were in demand and a slightly labor- “born” about the same time as baby boomers (e.g.
reduced version but of equal measuring accuracy 60 years ago give or take), it can also start a discus-
was made during this period. sion that ranges widely.
Here’s an example of the model made during WWII.

Item #287
Millers Falls 0-1” micrometer in wood box with
a lock and their unique speeder and ratchet.
Satin chrome, .0001 reading, and very nice condition.

$35 donation

Item #288
Millers Falls company merger pack, consisting
of two essentially identical 0-1”
micrometers in fitted leatherette cases.
The first example came with a Goodell-Pratt case and a
Goodell-Pratt micrometer that could date from either
before or a bit after the merger with Millers Falls. The
second example came to me with a Millers Falls card-
board box, a Goodell-Pratt case, and a Millers Falls mic
within. Apparently they had a stock of the Goodell-
Pratt cases. Both mics in nice condition, with decimal
equivalents on the thimble.

$60 donation

105
Item #289
Millers Falls No. 701R micrometer 0-1” with
speeder, lock, 0001” vernier, and black frame.
Nice mic complete with a wood case.

$30 donation

Item #290
Millers Falls No. 112R micrometer 0-1” with
speeder, ratchet, lock, decimal equivalents and
the original wood box.
Nice mic for an aspiring engineer willing to take care
of it.

$35 donation

Item #291
Matched pair of Millers Falls No. 112R and 20R
micrometers 0-1” and 1-2” with speeders, ratch-
ets, locks, and decimal equivalents.
Great set covering the most commonly measured
range.

$55 donation

Item #292
Millers Falls 20R micrometer 1-2” with decimal
equivalents on the thimble.
Average condition; showing some signs of wear from
use.

$20 donation.

106
Mitutoyo
(Tokyo) was founded by Yehan Numata in 1934. The first commercially available micrometer was pro-
duced in 1937. As with English and German makers, demand for micrometers increased along with
production for WWII. Mitutoyo’s Kamata factory was burned to the ground during the war, but pro-
duction of micrometers restarted in 1947 with full production in 1949. Perhaps aided by a fresh start,
Mitutoyo has gone on to become one of the world’s great full-line precision instrument manufacturers.
In many ways, it now out competes such century-and-a-half old stalwarts as B&S and Starrett in hand
instruments.

Item #293
Mitutoyo > Poland two pack.
A typical Mitutoyo 0-1” micrometer and its Polish 0-1”
counterpart, as Poland liberalized and emerged as an
export manufacturer in the 80’s. Note the similar
hammertone painted frame style, lock, carbide anvils,
graduations, and friction thimble. Not an exact copy,
but a clear emulation. Both mics are excellent for use,
both with verniers and all the usual features. The nod
goes to Mitutoyo for quality, but the Polish mics are
still quite accurate. See also “VIS” – the same Polish
micrometer with a brand name affixed.

$45 donation

Item #294
Mitutoyo #102-121 (0-1”) and #102-122 (1-2”)
micrometers.
Mitutoyo quality is world class and these are higher end
examples, with a carbide anvils, sturdy chrome finish,
thermal pads, ratchet, lock, and .0001 vernier. The
0-1” is like new, the 1-2” has had some wear, mostly
to the case and pads. Very nice set for decades of use.
Current price (they are a contemporary design) for
these would be about $250 for the pair.

$115 donation

107
Item #295
Mitutoyo #106-102 0-1” mint condition in wood
case.
Mitutoyo is one of the world’s finest makers of precision
tools and Japan’s leading company in this field. This
particular model has several unique features. First, it
has a non-rotating spindle. This has the advantage of
not placing any torque on the material to be measured
and also of reducing wear on the anvils. Second, it
is very easy to read, with a large thimble, large gradu-
ations, every thousandth numbered, an easy to read
vernier. Third, it has outstanding ergonomics (similar
to the Etalon Microrapid, but without the fast feeding
screw) with a right-sized speeder and an excellent fric-
tion thimble. Fourth, it has an outstanding “feel” com-
parable to the very best models. I’ve acquired every
good condition example of this uncommon microm-
eter I could find; at the time thinking they would be the
perfect “congratulations” for outstanding technology
students. These are still available new, around $290.

$120 donation

Item #296
#106-102 0-1” micrometer
in near mint condition in wood case.

$110 donation

Item #297
#106-102 0-1” micrometer
very good condition, no case (blue bag) with slight
wear to front plastic pad.

$95 donation

108
Item #298
#106-102 0-1” micrometer
very good condition, no case, with new thermal pads

$95 donation

Item #299
Mitutoyo 0-1” and 1-2” micrometers; both .0001
reading with carbide anvils, ratchets and locks.
The 0-1” is all satin chrome with a plain yellow sticker
on the back; model 101-113 in original plastic case and
paperwork. The 1-2” is model 103-262 with a green
hammertone frame.

$50 donation for 2 mics

Item #300
Mitutoyo 0-1” model #293-721electronic digital
micrometer in new condition with box, original
paperwork, etc.
Battery is included but not installed. Instantly choose
between English and metric units, set a new zero
point, hold a measure, etc. Also includes an SPC (sta-
tistical process control) output port. This connects to
external readouts. Mitutoyo is generally considered
to make the best electronic micrometers and calipers
-- and this is a good example. Chinese clones have ap-
peared of this mic, but their quality level is much lower
(e.g. the circuit boards are sloppy in comparison) and
their batteries run down much faster.

$110 donation

109
Item #301
Mitutoyo 1-2” model #293-722 electronic digital
micrometer in excellent condition; and a good
mate to the micrometer above.
Has the box, measuring standard, etc. A battery is in-
cluded but not installed. Instantly choose between
English and metric units, set a new zero point, hold a
measure, etc. Also includes an SPC (statistical process
control) output port. This connects to external read-
outs. A good pair to model #293-721.

$100 donation; $195 paired with 0-1” above.

Item #302
Mitutoyo 0-1” micrometer with all satin chrome
frame, carbide anvils, friction ratchet, lock, dec-
imal equivalents, and .0001” vernier.
Nice mic in very good condition (no markings, accu-
rate).

$35 donation

Item #303
Mitutoyo 0-1” micrometer #103-135 with green
hammertone frame, friction thimble, lock, and
.0001 reading vernier.
Mitutoyo is one of the few manufacturers making the
same model micrometer in different factories; and this
one is made in Brazil. Mic has a QC control numbers
obscured. It looks pretty good and is in accurate op-
erating condition.

$20 donation

Item #304
Mitutoyo 0-1” micrometer #103-135 with green
hammertone frame, friction thimble, lock, and
.0001 reading vernier.
Same design and model number as above, but made in
Japan rather than Brazil. Unmarked condition with
slight wear on the rear plastic pad.

$25 donation

110
Item #305
Mitutoyo 0-25mm mechanical digital microm-
eter #193-111.
Near new condition with no signs of wear to the pads,
etc. Includes ratchet, lock, and .001mm vernier. New
price on these, for a slightly cost-reduced version, is
$142 (Amazon.com).

$50 donation

Item #306
Mitutoyo 25-50mm mechanical digital microm-
eter #193-102.
Near new condition with no signs of wear to the pads,
etc. Includes ratchet and lock. This would be a great
pair with the corresponding Mitutoyo 0-25mm me-
chanical digital mic (#193-111) above.

$50 donation

Item #307
Mitutoyo 25-50mm micrometer #101-116.
This is new old stock, with the mic still sealed in its
original plastic bag. Includes an all satin chrome
frame, the older style stamped steel lock (not plastic), a
friction thimble, and standard. New cost about $110
(and this example is new, complete with case).

$40 donation

Item #308
Mitutoyo #143-121 with extended caliper-type
anvils meant to reach into tight places.
Works fine for regular measurements as well. Green
hammertone frame, a ratchet, and .001” reading. Mi-
tutoyo is the only modern manufacturer (AFAIK) to
make such a micrometer. Still in current production,
at around $310 (Amazon discount price). This one is
in very good condition, with slight signs of wear on the
rear pad (where it rests).

$95 donation

111
Item #309
Mitutoyo #143-121 and #143-122 micrometers
with extended caliper-type anvils meant to reach
into grooves and tight places.
Works fine for regular measurements as well. Green
hammertone frame, a ratchet, lock, and .001” reading.
Includes both 0-1” and 1-2” sizes. Mitutoyo is the only
modern manufacturer (AFAIK) to make such a mi-
crometer. Still in current production, at about $650
for the pair. These are in excellent condition.

$195 donation for the pair

Item #310
Mitutoyo #112-177 point micrometer (sharp 15
degree points) in excellent condition with case.
These are meant for reaching even smaller features than
can be reached with blade and caliper type microm-
eters. Know someone whose life’s a pit? Measure the
precise depths of their despair. A bit over $165 new.

$65 donation

Item #311
Mitutoyo #112-237 point micrometer (sharp 30
degree carbide points).
This is similar to the model #112-177, but with carbide
tips and a 30o rather than 15o point. These are meant
for reaching small features such as grooves and the web
thickness of drills. This one is in very good shape, no
extra markings, but a couple of paint dings etc. from
light use. About $170 new.

$60 donation

112
Item #312
Mitutoyo #227-101 low pressure 0-25mm mi-
crometer.
The low anvil pressure device and readout allow ac-
curate measurements in soft materials. Yet another
unique method of controlling pressure for accuracy.
This has a friction thimble. Mint condition in original
case and cardboard sleeve.

$90 donation

Item #313
Mitutoyo 0-25mm double-headed micrometer
#113-102 in near new condition.
This is what happens when micrometers have Siamese
twins. The idea is that one spindle can be set to the
high tolerance and the other to the low tolerance to
create an instant “go, no-go” gage. Slocomb pioneered
this and is the only other company I’ve seen to make
one. Light blue hammertone frame, with carbide an-
vils and two locks. It will work fine for regular mea-
surements as well. Keep it around and tell people you
always want a second opinion. Still available; a bit over
$200.

$90 donation

Item #314
Mitutoyo Model No. 510-101 0-25mm indicating
micrometer in mint condition.
Includes a .001mm comparator, anvil release, and lock.
Light blue hammertone frame finish. Eminently accu-
rate and useful. Kinda cool. Support the MKS system
of units!

$100 donation

113
Montgomery Ward
Item #315
Montgomery Ward Powr-Kraft inside microm-
eter set with a 1.5” to 8” range -- made for them
by the Central Tool Co. around 1966.
Satin chrome, in good condition in its original black
case and instruction slip.

$40 donation

Moore & Wright

Moore & Wright (Sheffield etc., England) was 1945. Shaw embarked on making M&W a full
founded in 1906 by Frank Moore. Over the years range supplier. The company was acquired by the
it became a full range and world-class supplier Neill Tools Group in 1970 (Shardlow was another
much like B&S and Starrett in the US and Mitu- Neill acquisition). To its credit, the company went
toyo in Japan. Indeed, there is so much competi- on the create the world’s first hand-held digital mi-
tive give and take among leading suppliers that crometer (the Micro 2000), for which it received the
many examples of tools look to be copied back and Queens Award for Technological Achievement in
forth; and sometimes manufactured for each other. 1977.
For example, the 1970 M&W catalog (printed
before any mention of the Neill acquisition) M&W is now part of the Bowers Metrology Group,
shows mechanical digital mechanisms the same as with factories in the UK and China. It appears
used in Brown & Sharpe and likely sourced from that many recent micrometers (2009 catalog) are
Switzerland. Other designs closely copy Mitutoyo sourced from China. All in all, another chapter in
(enamel frame mics) and Starrett (mics with deci- the consolidation of precision tools manufacture.
mal equivalents on the thimble). I addition to generally high quality for most of its
The peak of production may have been WWII. years, one neat feature of the M&W outside mics
Ownership passed from Frank Moore to his daugh- is a pointer tally, useful in repetitive measurement
ter. She, in turn, sold it to the John Shaw Co. in comparisons.
Item #316
Moore & Wright #961BY all satin chrome 0-1”
mic
with friction thimble, pointer tally, lock, and decimal
equivalents. Old eyeglass style case.

$30 donation

114
Item #317
Moore & Wright #965F 0-1” mic
from the Handsworth factory (since leveled). One of
the later designs before cost-reducing much of the line.
Enamel frame, friction thimble, lever lock. Probably
built not too long of Neill acquired M&W.

$25 donation

Item #318
Moore & Wright #961B (0-1”) mic in satin
chrome, with lock, ratchet, etc.
Comes with original packaging, outstanding condi-
tion, and likely from a period not too long after the
Neill acquisition.

$35 donation

Item #319
Moore & Wright #965 (0-1”) and #966 (1-2”) mi-
crometers.
Good quality mics with decimal equivalents on the
thimble (much as Starrett did in the mid 1900’s before
cost-reducing the #436 line)

$45 donation

Item #320
Moore & Wright #961 (0-1”) and #966 (1-2”) mi-
crometers.
The 1” is in an older eyeglass style case, very nicely
made in all satin chrome. The 2”is a wood case. Both
are near mint.

$55 donation

Item #321
Moore & Wright 0-1” Braille micrometer for-
merly owned by the Sperry Gyroscope Co, Ltd.
(see the slip of paper within). Somewhat amazing as
a tool and very amazing when one considers the users.

$90 donation

115
Item #322
Moore & Wright 0-1” bench micrometer with
very large “pearl chrome plated” thimble, direct
reading in ten thousandths of an inch.
This shows up as model No. 476 in Moore & Wright’s
1952 catalogue. It has a speeder on the end; with its
original wood case and paperwork. Near new condi-
tion with a silky feel.

$100 donation

Item #323
Moore & Wright “Micro 2000” electronic digital
micrometer.
Mid 70’s. Recognized as the world’s first hand-held
digital micrometer. This unit is in good cosmetic
condition, but there was a break in the charger plug
and the (35 year old?) NiCad batteries are surely dead.
Possibly restorable. Maybe just an artifact, complete
with its “Patent Pending” notice.

$50 donation.

MTG, Inc.
was founded in 1967 and has began making a modular line of hand-held indicating gages 1970. Small
company, well respected in its niche.

Item #324
MTG internal gage frame with fingers and Ger-
man-made .0005” comparator.
This is set to a desired internal measurement, inserted
using plunger to retract the fingers, with deviations
noted on the comparator dial. Can be set up with dif-
ferent fingers to measure bores, grooves, internal fea-
tures, and the like. Costly gage, in excellent condition.

$225 donation

Mueller Gages Co.

(Pasadena, then San Gabriel, CA) was founded in 1949.

116
Muskegon Tool Industries, Inc.
(Muskegon, MI) was founded in 1958. It focuses on tools for drilling and boring.

Item #325
Muskegon 0-6.5” bore setting gage.
This is set to zero with gage blocks, and then used to
check and set various boring tools. Includes a .0001”
reading Starrett dial comparator. Near mint condition
in nice fitted wood case.

$90 donation

MZB
(Germany). Some of their tools are marked “Western Zone.” Possibly the same company as Messzeug-
bau Reichenbach GMBH?? My example looks to be made for export.

Item #326
MZB 0-1” micrometer,
nice overall construction will all the usual higher end
features (satin chrome, lock, ratchet, decimal equiva-
lents).

$25 donation

Nachi
(Japan) dates to 1889. They started making micrometers in the late 30’s.
Item #327
Nachi
0-25mm, 25-50mm, and 50-75mm micrometers in
original fitted wood boxes. Long ratchet / speeder,
and lock. A standard all-steel micrometer design seen
worldwide. As best I can tell this set (3) of microm-
eters dates from the late 30’s to before or after WWII.
These are still quite usable; and also make an interest-
ing comparison to US and other mics of the same era.

$90 donation

National
-see Central Tool Company

117
Neue Berliner Messingwerke
(Berlin). English translation: must “messing” around means metalwork. Patents assigned to this com-
pany go back to the late 1800’s and early 1900’s (including a US patent granted in 1909).

Item #328
Neue Berliner Messingwerke
0-15mm micrometer with brass frame and nicely
knurled steel frame. Perhaps as much as 100 years old?

$30 donation

Nippon Seisoku
(Tokyo, Japan) roughly translates as Japan proper/correct. Logotype is a curved “N” superimposed over
an “S” with in a circle.

Item #329
Nippon Seisoku 25-50mm interchangeable anvil
thread micrometer.
Includes three anvil pairs to cover threads from .6 to
3mm, original wood box, ratchet, and lock. Satin
chrome thimble and plain steel frame. The 4mm di-
ameter anvil size will fit at least some Mauser and Fein-
mess thread micrometers.

$40 donation.

NSK
(Tokyo, Japan). Nippon Seiko Kabushik Kaisha, a.k.a. Japan Micrometer Mfg. Co., began in 1916 as Ja-
pan’s first bearing manufacturer. NSK started development work on micrometers in the early 30’s, along
with Japanese competitors like Mitutoyo, Misuiseiki, and Fugikochi.
NSK made a variety of precision products, and were distributed in the US by Fred V. Fowler (marked
NSK/Fowler) to the manufacturing industry and by Snap-on to the automotive industry. Draper brand-
ed mics were also made by NSK. The NSK Japan factory is no longer making micrometers according to
one source. These are of high quality, and very similar in such details as the lock to Mitutoyo.
Item #330
NSK 0-1” micrometer in original plastic case
with 1968 factory calibration report (“A” rating)
and original paperwork, chamois cloth, etc.
Model AA02 with all satin chrome frame, .001 reading,
ratchet, and machined lever lock. Like new.

$30 donation

118
Item #331
NSK 0-1” micrometer with friction thimble,
lock, carbide anvils, and .0001 vernier.
Good condition but unmarked (painted) thermal pads.
Excellent “user” micrometer.

$25 donation

Item #332
NSK 0-1” micrometer with gray hammertone
frame, friction thimble, lock, carbide anvils, and
.0001” reading vernier.
Good cosmetic (no markings) and working condition.

$25 donation

Item #333
NSK 0-1” micrometer #UAAB02 in original
wood box.
Gray hammertone frame with ratchet and .0001” ver-
nier. Likely one of their earlier mics, given the wood
case, the stamped frame inscription versus plastic
pads, and the wood rather than plastic case. Late 50’s
or early 60’s? Very good condition.

$30 donation

Item #334
NSK 0-1” micrometer in gray case marked
#YUXB 01-1.
Grey hammertone frame, friction thimble, lock, and
.0001” reading vernier with original paperwork. Mic
inside is in mint condition.

$30 donation

119
Item #335
NSK 0-1” micrometer with carbide anvils,
a ratchet, machined lever lock, .0001” vernier, satin
chrome frame, and plastic thermal pads. Also in-
cludes a 1967 factory test report showing zero screw
thread errors and an “A” rating, plus an NSK manual.
Note that the box description and the micrometer do
not match; though this does appear to be a circa 1967
or earlier mic. Mic is in excellent condition, except-
ing some cosmetic delamination from within the clear
plastic pads

$35 donation

Item #336
NSK matched set of four mechanical digital mi-
crometers with gray hammertone frames, .001”
mechanical readouts, and .0001” verniers.
Includes ratchets and locks. Very good quality, on par
with Mitutoyo and with some unique features such as
easy zero setting. While all four micrometers are in
very good to excellent condition, there are some differ-
ences. The 0-1” looks near new, but has no case. The
1-2” looks like new old stock and has its original wood
case, standard, adjustment tools (which work for all
mics in the set), and manual. The manual is clear, but
with a few “charming” bits of translation. The 2-3”
size is in very good shape. It includes a standard but
no case. The 3-4” size looks near new, with its origi-
nal wood case, standard, tools, and paperwork. NSK
no longer makes micrometers; but an equivalents set of
Mitutoyo mechanical digital micrometers would cost
about $800 today. These are accurate mics, easy to
read.

$195 donation for the set of 4

120
Item #337
NSK matched set of two mechanical digital mi-
crometers with gray hammertone frames, .001”
mechanical readouts, and .0001” verniers.
Includes ratchets and locks. Very good quality, on par
with Mitutoyo and with some unique features such as
easy zero setting. The 0-1” mic is in very good condi-
tion, with no case. The 1-2” micrometer looks to be
near new, with its original wood case, standard, adjust-
ment tools (which work for both mics in the set), and
manual. NSK no longer makes micrometers; but an
equivalent set of Mitutoyo mechanical digital microm-
eters would cost about $400 today. These are accurate
mics and easy to read.

$95 donation for the pair

Item #338
NSK 0-2” micrometer with anvil adapter to mea-
sure 0-1” (which is removed for 1-2” measure-
ments).
The mic looks like new, but has a cracked gray plastic
case. It includes a ratchet, lock, and all satin chrome
frame. The adapter idea goes back about a hundred
years.

$50 donation

Item #339
NSK #YUX01 (0-1”) and #YUX02 (1-2”) analog
micrometers.
Mint condition.

$115 donation

Item #340
NSK #YUX01 (0-1”) and #YUX02 (1-2”) analog
micrometers.
The 0-1” in this set has a small flaw – it is lightly marked
“QA” for quality assurance dept. on the back. similar in
such details as the lock to Mitutoyo.

$95 donation

121
Pacific Gage Co, Inc.
(Hermosa Beach, CA)

Item #341
Pacific Gage Co. “Height Master” 0-16” height
gage, with large .001” direct reading microm-
eter head.
An interesting design (many had a continuous beam),
included mainly because a COFES tables full of mi-
crometers will be a little less boring with something
standing above the ray. These are used on a large sur-
face plate to lay out and measure work (see also the
Cadillac gage). A Mitutoyo .001 test indicator (with
reversing switch, indicator clamp, height gage adapter,
and height gage clamp have been included so it can be
set up to give a sense of use. It might also be used
with a sharp scriber. Includes the 16” height gage, fit-
ted case, and .001” Mitutoyo test indicator.

$120 donation

PAV
(Liechtenstein). High quality supplier of precision tools, still in business.
Item #342
PAV 0-25mm micrometer
with heavier and easier to read construction than most.
Ratchet, lock, thermal pads, satin chrome, in wood
box. Excellent.

$50 donation

122
Pi Tape Corporation
was founded in the mid-40’s (company information can be found at www.pitape.com ). The idea seems
obvious in retrospect. Make a very precise steel tape where 3.14159... inches is marked as an inch, put
a vernier on the end to measure to .001, and wrap the whole flexible tape around cylindrical objects to
determine their diameter. Obvious, perhaps, but ignored in a century of prior measurement art. This
may be because no one was making many highly precise cylindrical objects until we started making tur-
bines, jet engines, rockets and the like? Not a micrometer (no screw thread), but a worthy competitor for
measuring large work.

Item #343
84 to 96” Pi Tape in open aluminum case.
Formerly owned by Airco Temescal, which made
things such as large stainless steel vacuum chambers
– maybe up to the 8’ diameter of this tape. Dirty case,
clean Pi tape.

$30 donation

Pierre Roch S.A.R.L.

(Rolle, Switzerland). The company adopted the Etalon trademark after WWII. A fine quality maker,
it’s micrometers and other precision measuring tools became part of TESA. TESA then became part of
Hexagon.
Item #344
P.ROCH 175-200mm micrometer marked
“PROCH” and “ROLLE, SUISSE” within a shield-
shaped logo and a Swiss cross.
Includes a ratchet, knurled circling type lock, wrinkle
black frame, large plastic thermal pads, and a black
leatherette case. “PROCH” is almost surely Pierre
Roch (P.ROCH) of Rolle, Switzerland and bears some
resemblance to that company’s subsequent Etalon mi-
crometers. Fine quality micrometer of conventional
design.

$65 donation

123
BZG Polyplan
(Geneva)

Item #345
Elaborate 0-4” micrometer set with Microfix
rapid/mechanical digital thimble.
This is the most gorgeous, bordering on anal reten-
tive toolmaker’s micrometer set I’ve seen. Only the
Swiss would have made it. It includes a very high qual-
ity rapid thread thimble, exactly as also seen in some
rare Steinmeyer micrometers (also in the collection)
and similar to the famed Etalon Microrapid. What
makes this set unique is a set of 9 attachments, built
to gage block tolerances, that expand the range in 1”
increments up to 4.” The set then includes six different
anvil types for a wide variety of measurements. these
include a small circular base to use it as a bench mi-
crometer and others to use it as a standard microm-
eter (attached), a V-angle (3 point and concentricity),
pin micrometer (tubing etc.), blade (small spaces), and
triangle (thread?) micrometer. I’ve never seen anoth-
er example of this micrometer and doubt it could be
made for much less than $2000 today.

$400 donation

124
Lufkin / Pratt & Whitney
began in 1860 as a maker of guns and gun making machinery – using the then-innovative idea of inter-
changeable parts. By 1885 they were making a precision measuring machine; by 1918 “Hoke blocks”
(following the general idea of “Jo blocks”); and by 1926 they introduced their first Supermicrometers.
Their famed aircraft engine business (now part of United Technologies) was an offshoot of Pratt & Whit-
ney Machine Tool around 1925. P&W acquired Lufkin’s precision tools business in November 1966.
Pratt & Whitney marked micrometers are of identical design and high quality to the last Lufkin microm-
eters.

Item #346
Pratt & Whitney set of 3 micrometers 0-3” made
by Lufkin.
Lufkin made gorgeous precision tools, as well as the
carpenter’s rules it is better know for. This set is from
right around the time that Pratt & Whitney acquired
Lufkin, with the 0-1” and 1-2” mics marked P&W, but
the (identical model) 2-3” mic marked Lufkin. Nice
mics with a bit of business and competitive history be-
hind them.

$90 donation

Item #347
No. 1961 Pratt & Whitney 0-1” micrometer in
near mint condition.
Nice mic with satin chrome friction thimble, lever lock,
and black wrinkle paint frame.

$35 donation

125
Item #348
Pratt & Whitney precision end measures and in-
side micrometers, in original wood box.
Includes two micrometer heads and nine precision
rods (made to gage block tolerances) ranging from 1”
to 12” in length. Lined up together they provide more
than 36” of range, with .0001” increments set on the
micrometer heads. The Moore Tool Company, with its
Moore jig bores established a unique method of precise
coordinate measurement – to even tighter tolerances
than were possible with a precision screw. Basically, a
set of gages like these were laid in a sort of tray on the
X or Y axis (thus two micrometer heads, one for each
axis) and the jig bore table moved to a hard stop. These
appear to be in very good condition, with QC calibra-
tion numbers on the mic heads.

$70 donation

Rank Taylor Hobson Ltd.

Item #349
Rank Taylor Hobson #142/43 type TB 100 Mi-
croptic Clinometer in fitted wood case with in-
structions.
Not exactly a micrometer (though precision screws
drive the angular adjustments) and a “micrometer
scale” vernier is used to measure angles to 10 seconds
of arc. Angles are read through the eyepiece at the
top. I decided it was cool enough to include for the
discerning COFES crowd. Now you can truly know if
your colleagues are on the level. As can be seen with
the enclosed paperwork, these were pricey bits of me-
chanical ingenuity, still fetching around $1600 on the
used market/

$395 donation

126
Reed & Prince Mfg. Co.
(Worcester, Mass) was incorporated in 1902 by Edgar Reed and others. It acquired micrometer patents
dating to 1901 and soon began making micrometers. Reed’s son (E. Howard Reed) took over the com-
pany and formed the Reed Small Tool Works in 1916.
Item #350
R&P Mfg. Co. 0-1” with chrome plated frame.
This dates between 1902 and 1916; likely before WWI.

$30 donation

Reed Small Tool Works

1916 to circa 1945 was formed out of Reed & Prince Mfg. Co. By 1921 it was manufacturing microm-
eters for sale by others; including Cenco, Fleming, and others. The micrometer business was sold to the
Tubular Micrometer Co.; probably just after WWII. Reed designs showed up as solid frame micrometers
in the Tubular Micrometer / Tumico / Scherr-Tumico lines.
Item #351
Reed Small Tool Works 0-1” micrometer with a
patent date of Jan 1901 engraved on the thimble.
A nicely designed and forged frame along with the
thimble-based adjustment design that would (slight-
ly modified as it moved down the thimble) continue
through to Scherr-Tumico days.

$30 donation

Item #352
Reed Small Tool Works 0-1” micrometer with a
cool set of decimal equivalents pressed into the
frame.
Excepting the equivalents markings, this is essentially
the same design as the plain forged frame. It has the
early style of adjustment, with the spanner hole to-
wards the end of the thimble. Early 1900’s.

$35 donation

127
Item #353
Reed Small Tool Works 0-1” micrometer with all
the features; pressed decimal equivalents in the
frame, a ratchet, and a lock.
Nice mic with a bit of history. Has the older location
for the adjustment spanner. Reference “A.”

$45 donation

Item #354
Reed Small Tool Works #901 0-1” microm-
eter with decimal equivalents conventionally
stamped.
Includes .0001” reading vernier. I suspect this came
as either a cost reduction to their forged frames or a
response to requests for easier readability.
Otherwise, typical Reed design.

$25 donation

Item #355
Reed Small Tool Works #901 0-1” microm-
eter with decimal equivalents conventionally
stamped.
Similar to the other #901 example with plain stamped
decimal equivalents, a ratchet and lock -- but without
the vernier markings.

$20 donation

Item #356
Reed Small Tool Works 0-1” micrometer with
what would become their classic black frame
(continued in style with Tumico and Scherr-Tu-
mico).
Includes .0001” reading vernier. It would be easy to
improve the cosmetic condition of this mic; and the ac-
curacy is good. Reference “B.”

$25 donation

128
Item #357
Reed Small Tool Works 1-2” micrometer.
Classic frame with .0001” vernier and a lock. This
would make a nice set with the micrometer marked
“Reference A” – also with a lock.

$30 donation / $65 for this plus “A”

Item #358
Reed Small Tool Works 1-2” micrometer with
.0001” vernier and no lock.
This would make a good set with the micrometer
marked “Reference B.”

$25 donation / $40 for this plus “B”

Regal Beloit, Inc.

began in 1955 (as Beloit Tool) in a roller skating rink in Beloit, WI; moved to South Beloit, IL in 1961;
renamed itself Regal-Beloit in 1969; and moved its headquarters to Beloit, WI in 1991. Typical products
were cutting tools and gear boxes. After a series of acquisitions it is now a sort of electrical conglomerate
with around $2 billion annual sales.
Item #359
Regal Beloit marked 0-1” and 0-25mm combi-
nation metric and inch micrometer made by the
Ambrose Shardlow Co. (Sheffield, England).
A clever combination inch and metric micrometer. I
presume that Regal Beloit thought this would be a sen-
sible companion product to cutting tools?? Note the
dual scales on the barrel and thimble. Near mint con-
dition, with soft case. Well made, with ratchet thimble,
a unique push button lock, and instructions for read-
ing.

$40 donation

129
Rimat Tool Co.
(Glendale, CA)

Item #359
Rimat bore micrometer .7” to .9” range.
Carefully made tool from a seldom seen maker.

$30 donation

Sawyer Tool Co.

(Athol, then Fitchburg, then Ashburnham, MA) was founded by Burnside Sawyer in 1894. Montgom-
ery & Co was an early distributor beginning even earlier (1891). The company moved from Athol to
Fitchburg in 1902. The company was sold to Carl Hubbell in 1908 (who was also involved with the T.R.
Almond Co.) and moved to Ashburnham in 1912.
Item #360
Sawyer Tool Co. inside micrometer set in origi-
nal black leather case.
It’s marked “Fitchburg,” dating it from 1902 to 1912.
Very good condition, with four of its spacers.

$50 donation

George Scherr Co.

(NY) The company advertised in such places as Popular Mechanics and Popular Science (1942-48) and,
as a distributor, affixed its name to such products as Mauser vernier calipers and indicating mics and Tu-
mico micrometers. The only (undated) catalog I’ve seen dates from about 1950; listing the 1950 edition
(14th) of Machinery’s Handbook.
Item #361
Scherr 0-1” micrometer made for them by Reed
(or, later, Tumico).
Satin chrome thimble, .0001 reading, in good shape.
Reference X.

$20 donation

130
Item #362
Scherr 1-2” micrometer made for them by Reed.
.0001 reading. Slight paint wear, scratches.

$15 donation / $30 for this plus “X” above

Item #363
Scherr 0-1” and 1-2” micrometer set with .0001
verniers.
Made for Geo. Scherr Co. by Reed (or possibly Tumico
after acquiring Reed). A vintage set, probably from the
late 40’s or early 50’s, that looks to be accurate and in
good condition. Includes ratchets and locks.

$50 donation

Item #364
Geo. Scherr Co. 0-1” branded micrometer likely
made for them by either Reed Small Tool Works
or the Tubular Micrometer Co.
The date is likely around the time Reed sold to Tubular.
Includes ratchet, lock, .0001 vernier, and all chrome
frame. Marked #901 and of the same basic design of
Reed Small Tool Works #901 and later #901 Tumico
micrometers.

$30 donation

Item #365
Geo. Scherr Co. 1-2” micrometer made for them
by the Tubular Micrometer Co.
Reed design frame with .0001” vernier. Good example
of how one thing leads to another. Scherr puts its house
brand on Tumico mics. Later, the companies merge to
form Scherr-Tumico.

$30 donation

131
Scherr-Tumico Company
Scherr-Tumico Company (St. James, Minnesota) of the Reed designs.
has a heritage going back decades. It started just
(before?) after WWII as the Tubular Micrometer The company has always made good quality mi-
Company (Tumico) and was famous for its light- crometers, but was a perennial runner up to Star-
weight vacuum sealed tubular micrometer frames. rett and Brown & Sharpe in brand recognition (and
Especially in larger sizes these were easier to use. also a good example of how the top two suppliers
Along the way it acquired the micrometer business in a market often dominate; as in Pepsi and Coke
of Reed Small Tool Works which itself dates back to versus Dr. Pepper etc.) It’s niche for many years
1902 as the Reed & Prince Company. Later, the Tu- was selling precision tools to the US government.
bular Micrometer Company merged with a preci- Scherr-Tumico also built micrometers for others
sion tools distributor, the George Scherr Company, to sell under their brand name. These included the
to become Scherr-Tumico; probably around 1960. Central Scientific Company (laboratory equipment)
At some point it was part of the Rank organization and Sears Roebuck. As with many US suppliers it
(e.g. Rank Scherr-Tumico, Inc.). More recently it most recently started selling Chinese-made tools;
has gone by the name S-T Industries and also estab- usually of a somewhat lower quality. The old US-
lished the Accupro brand. made micrometers are, in my opinion, equivalent in
quality to the Starrett #436 series, but not nearly so
The smaller micrometers (including several sets well known.
available here) may have solid frames along the lines
Item #366
Scherr-Tumico 0-1” micrometer; listed in their
1961 catalog as the new “190” series.
This is a well designed micrometer with a speeder at
the end, a large thimble-base ratchet with a soft action,
and a nicely detailed lock. Lead error is held to less
than 50 millionths (as with all of S-T’s ground screws)
and the “Silver Mist” chrome frame includes decimal
equivalents. Try it.

$40 donation

Item #367
Scherr-Tumico tubing micrometer 0-1” with
black wrinkle frame, ratchet, and lock.
This is designed for measuring the wall thickness of
tubing and pipe. Works for a variety of other measure-
ments as well. Excellent condition apart for a spot or
two of paint wear.

$40 donation

132
Item #368
Scherr-Tumico 0-1” and 1-2” pair of microm-
eters in their own fitted wood boxes.
Black wrinkle frames, ratchets, locks, and .0001 verni-
ers. Good quality micrometers in near mint condi-
tion. 1 of 2.

$60 donation for the pair

Item #369
Scherr-Tumico 0-1” and 1-2” pair of microm-
eters in their own fitted wood boxes.
Black wrinkle frames, ratchets, locks, and .0001 verni-
ers. Good quality micrometers in near mint condi-
tion. 2 of 2.

$60 donation for the pair

Item #370
Scherr-Tumico 0-1” x 3” deep throat micrometer
with wrinkle black frame, in original wood box.
Includes ball end anvils, a ratchet, and lock. Near new
condition.

$45 donation

133
Item #371
Scherr-Tumico 0-1” by 12” deep throat microm-
eter.
The heavy frame allows accurate measurements deep
into sheet materials (metal, paper, plastic . . .). This
was formerly owned by Tektronix, Inc. and other than
numbering the gage for quality control in 1987, it looks
to be unused. Here’s the urban legend (I’m making this
up) you can spread: Tektronix bought this to better
control sheet metal thickness for it’s amazing new (way
back when) 4014 storage tube workstations. However,
just as they bought it, demand for storage tubes tanked.
That leaves this as one of the remaining manufactur-
ing artifacts from a period some of us can remember.
FWIW, a new 12” deep throat micrometer runs about
$300.

$100 donation

Item #372
Scherr-Tumico 0-1” test stand with huge (3”)
thimble, reading directly in .0001”
A costly micrometer head in like new condition ($435
new) mated to a fixture designed for checking the lin-
earity of dial indicators. Includes a Central Tools 0-1”
dial indicator. By leaving a plug gage (or the indicator)
in the fixture it can be used as a bench micrometer, af-
ter adjusting to zero.

$80 donation

Item #373
Scherr-Tumico 1-2” micrometer in fitted black
case. ratchet, lock, and all chrome design.
Nice working condition, but cosmetic damage to the
tubular frame (presently covered by chromed film).

$25 donation

134
Item #374
S-T Industries Accupro “Gold” new old stock set
of gage blocks.
Import, but calibrated. In a useful range for checking
and calibrating micrometers.

$35 donation

Item #375
S-T Industries Accupro “Gold” new old stock set
of gage blocks.
Import, but calibrated. In a useful range for checking
and calibrating all those micrometers you’ve so gener-
ously bought. Second instance.

$35 donation

Item #376
Scherr-Tumico set of three “850 series” microm-
eters; 0-1, 1-2, and 2-3 inches.
Black wrinkle finish solid frames of the Reed-origin
design. “Silver Mist Chrome” thimbles, .0001” vernier
reading, with a somewhat unique spindle lock design.
Useful set of good quality micrometers.

$75 donation

Item #377
Scherr-Tumico 0-3” micrometer set (three
.0001” reading mics) in a fitted wooden case.
Like new condition with ratchets, locks, standards, and
black wrinkle finish frames. A nice set for use.

$90 donation

135
Item #378
Scherr-Tumico set of four micrometers 0-4” in
blue vinyl case.
Includes ratchets and locks. Black wrinkle paint is a bit
rough, but easily restored to like-new condition. Oth-
erwise, very good condition. Add the 4-5” and 5-6”
sizes for a complete 0-6” set for $140.

$70 donation.

Item #379
Scherr-Tumico 4-5” micrometer with .0001” ver-
nier, ratchet, lock, setting standard, and black
wrinkle frame.
Near mint, in old B&S case. USA made.

$40 donation; $35 if bought with 0-4”

Item #380
Scherr-Tumico 5-6” micrometer with .0001” ver-
nier, ratchet, lock, setting standard, and black
wrinkle frame.
Near mint, in old B&S case. USA made.

$45 donation; $35 if bought with 0-4” & 4-5”

Item #381
Scherr-Tumico / Accupro 0-6” micrometer set;
new old stock with original box and still-sealed
micrometers and standards.
.0001 reading with ratchets, locks, and wrinkle black
frames. A good US-made set that cost nearly $600 be-
fore manufacturing was moved to China. See, above,
for a 0-6” set at $140.

$245 donation

136
Item #382
Scherr-Tumico 2-6” and 6”-9” interchangeable
anvil micrometers
with the famous hollow frames in a black wrinkle fin-
ish. The 2-6” size is government surplus, complete,
and in near-new condition in its wood case. The 6-9”
size is in good shape, but with no case and just the 8-9”
anvils. However, it can use the anvils from the 2-6” set
to get a full range. This would be ideal for a hobby ma-
chinist who does most of the measuring with 0-1” and
1-2” mics, but occasionally needs to work with some-
thing larger. Two mics, one price.

$85 donation

Item #383
Central Scientific Co. 0-25mm micrometer built
for them by Scherr-Tumico.
Good quality mic for a budding scientist.

Donation $25

Louis Schopper
(Leipzig)
Item #384
Deep throat micrometer, including display stand.
Louis Schopper founded his Leipzig workshop in 1881,
aimed at the textile and paper industries. This is a
paper micrometer of exceptional and elegant design,
with flat anvils to avoid indenting the paper. As best I
can tell it was made in the 1920’s and influenced by Art
Deco design. Most micrometers destined for a manu-
facturing life were pretty much oblivious to fashion,
but perhaps the paper/graphics industry was an excep-
tion? In any case a rare and exceptional instrument.
Schopper’s company has now become WPM Leipzig
Testing Machines.

$150 donation

137
Schmutz Mfg. Co.
(Louisville, KY). Decorative brass plates with the maker’s distinctive logotype – probably meant to be
affixed to machinery -- have been found. The company is also famous in legal circles for its involvement
in a statute of limitations / product liability case.
Item #385
Schmutz / B&S 6-12” interchangeable anvil mi-
crometer.
This mic is a bit of a puzzle. The frame is clearly marked
with a Schmutz Mfg. Co. logo and no other identifica-
tion except the 6-12” size marking on the reverse side.
However, the frame is clearly an old style #57 B&S and
the actual micrometer head is a Brown & Sharpe and so
marked. This micrometer frame style first appeared in
B&S catalogs during WWI (first appearing in Catalog
#27, 1916) and was phased out for a different style af-
ter 1935 (Catalog #32). The micrometer spindle, lock,
and frame are in good shape, but it is missing all but
the 11-12” anvil. One could likely get a used 0-6” B&S
interchangeable mic set and use the anvils from that to
get full coverage to 12”. I’d be more inclined to restore
the paint on the frame, polish the bright bits, and clean
up the logo. The name “Schmutz” is worth the price of
admission alone; along with the company’s subsequent
legal woes. Here’s a micrometer a lawyer could love?

$55 donation

138
Scru Meter
Item #386
Scru Meter 0-1” thread gage with all chrome frame
marked Pat. Apl. (patent applied for). The indicator
dial is B.C. Ames (see their listing) and the tool was
probably made by them. The traditional method of
measuring thread sizes is the “three wire method.” It
involves using sets of precise wires of different diam-
eters which are set into the threads; two on one side
and one on the other. A measurement over the threads
then shows the actual pitch diameter.
The problem, which this invention solves, is keeping
the threads in place while holding a screw and manipu-
lating a micrometer. This includes 8 pairs of wires em-
bedded in anvils plus various setting standards. Rare
– the only one I’ve seen – and likely dating from the
early 1900’s (Ames indicators go back that far). An
imaginative person will have an idea of just who should
receive their very own Scru Meter. Fitted wood box
with sliding trays.

$100 donation

139
Sears Roebuck and Co.
Sears Roebuck and Co. (Chicago, IL) was formally The 1975 catalog shows only Craftsman branded
formed in 1893. It revolutionized the catalog busi- mics; made for them by Scherr-Tumico and Mitu-
ness and early one provided most everything a toyo (mechanical digital).
homeowner might want (including the home, ap-
pliances, and furnishings) right through to farming, The 1980 catalog shows the same Craftsman-brand-
blacksmithing, and other equipment plus bicycles, ed Mitutoyo mechanical digital micrometer, a low
clothing, sporting goods, and even automobiles cost mic made by the Central Tool Co., and the bulk
from about 1905 to 1915.. The early catalogs are a of the Craftsman line made by Scherr-Tumico.
hoot. By 1990 the mechanical digital micrometers were
My 1901 Sears catalog shows a wide variety of tools, made by NSK (probably at slightly lower cost), the
including “Starrett’s Fay Patent” calipers; but not yet low cost apprentice micrometer made by the Cen-
micrometers. By 1927 Sears was also selling Fulton tral Tool Co. (Sears brand), and Scherr-Tumico
branded tools; which may also have been carried by made the bulk of the product line – but without the
Montgomery & Co (extensive tool catalog; with Ful- Craftsman brand name. Sears at that point was
ton looking much like a house brand) in the early downplaying its own brands, with more of a “brand
1900’s. The 1927 date is also when Sears registered central” strategy. The ST mics were offered in both
its “Craftsman” brand for tools; but it does not yet rolled (not so accurate, .001) and ground (more ac-
appear in that year’s catalog. By 1933 (likely ear- curate, .0001) threads.
lier; that’s the next catalog I have) Fulton was Sears’ By the 1995 catalog the NSK and Scherr-Tumico
economy brand for tools and Craftsman was the made mics (now Craftsman branded) were still
premium brand. Craftsman went on to become a there; along with Starrett micrometers.
respected brand for many decades; due to both the
quality and relative affordability of the tools and The 1997-1998 catalog shows both a Sears (NSK
their unconditional lifetime warranty. made, now demoted from “Craftsman” status) and
a Craftsman (Mitutoyo made) mechanical digital
While items were made to Sears specifications and micrometer. This must have been an interesting
branded by them, virtually everything was manufac- discussion with these competing Japanese suppli-
tured by someone else. On the micrometer front, ers and the Sears buyer. Both the Sears and Crafts-
perhaps a dozen different companies were suppliers man analog mics look to be made by Scherr Tumico
at one time or another. Goodell-Pratt looks to have (with rolled threads vs. ground threads setting the
made some early Craftsman micrometers; and the quality levels).
later Millers Falls.
By the 2000 catalog, Sears retained the Starrett mi-
The 1940 catalog shows a micrometer sourced from crometers as well as featuring “Craftsman” mechan-
Millers Falls. ical digital and electronic micrometers made by
Craftsman micrometers were made by the Central Mitutoyo. The Scherr-Tumico-made micrometers
Tool Co. in the early 1950’s. – after more than two decades of partnership --were
gone.
Sears also distributed a C.E. Johansson micrometer
in and around 1958. Machinists’ tools, including micrometers, com-
pletely disappeared in the 2004 catalog (kiss those
The 1960 hand tool catalog features Sears “best” customers goodbye), then reappeared in 2005. That
Craftsman micrometer on the front cover; made year’s catalog showed “special order” sets that look
for them by the Central Tool Co. It cost $16.98 at much like Chinese imports; but branded Crafts-
the time; about $125 in today’s dollars. In this same man. Starrett and S-T branded as Craftsman were
catalog (1960) Dunlap is the economy brand and also there.
Craftsman the top.
140
In 2008 and 2009 Sears once again killed off its – BMW’s 3,5, and 7 series or Mercedes C, E, and S
Craftsman branded micrometers, carrying only classes.
Starrett on special order.
Early on, Sears had two tiers. The original top tier
The current Craftsman Tools web site (2011) once was the Craftsman brand. The lower tier was vari-
again carries a variety of Craftsman-branded mi- ously branded “Fulton,” “Sears,” “Dunlap” (late 30’s
crometers with Scherr-Tumico back with analog to 1960 or so) and then the “Companion” brand.
micrometers and what looks to be a Chinese-made
“Craftsman” mechanical digital micrometer. There “Craftsman Commercial” and then “Craftsman Pro-
is also what might be a Starrett-made electronic mi- fessional” later added a third and top tier.
crometer sourced from China and sold as Crafts- With the influx of other brands (for example the
man. Taiwanese “GearWrench” in wrenches) Sears tool
The 2011 Sears web site also includes a variety of branding is now a bit chaotic. It has also been pos-
clearly Chinese micrometers branded “Skill Tech,” sible to find (e.g. with adjustable wrenches a decade
“KD Tools,” and “Chicago Brand.” The “Central ago) the lower priced Chinese import product that
Tools” branded micrometers shown may have also has better features and build quality than the higher
been sourced from China. All of these put Sears in priced US-made Craftsman product.
the position of offering undifferentiated products, Beginning around, say, 1990 the catalog/store busi-
at slightly higher prices than the competition for ness model was in decline. Perhaps Amazon.com
the same merchandise, with a somewhat less conve- and eBay – today’s retailing business model pio-
nient fulfillment process. neers -- will face similar issues long before their
In a sense, the history of micrometer sales at Sears own 100th anniversaries?
traces the business fortune of Sears. In recent decades Sears has made a number of
Early catalogs often show Sears offering three tiers moves that show a company managed more by ac-
of products. We humans tend to think we’re doing countants than retail wizards. For example, they
our homework with a consideration set of three; but sold off its parts division so that a third party could
quickly converge to a paired comparison. So, three jack up prices and alienate its customers. Later, the
tiers is just about right. By the mid 1960’s Sears was company was taken over by Kmart. Some Crafts-
the first company I know to have an explicit strategy man products, to the dismay of some once-loyal
of selling “good, better, and best” products. This customers, have dropped the unconditional war-
fits human decision making and is now widely seen. ranty and/or are being sourced from Asia.
Consider, for example, luxury cars with three levels

Item #387
Sears Craftsman 0-1” micrometer likely made
for them by Goodell-Pratt.
The desirable speeder and thimble-based ratchet de-
sign, plus a lock. Adjustment is through a screw at the
anvil end. Probably one of the first Craftsman-branded
mics; late 30’s to early 40’s. The 1933 catalog shows the
same Craftsman logo style with a micrometer clearly
made by Goodell-Pratt (with its unique lock at the rear
arc of the frame)

$35 donation

141
Item #388
Sears branded 0-1” micrometer made for them
by the Central Tool Co.
This has a friction speeder and silver painted frame,
just as the “Apprentice” micrometers noted elsewhere.
A cheap but usable micrometer.

$20 donation

Item #389
Sears “Fulton” 0-1” micrometer with chrome
plating over an aluminum die cast frame.
Includes friction/speeder and likely made for Sears by
Henry L. Hanson (see). Good condition.

$20 donation

Item #390
Sears “Companion” micrometer set 0-3” with
three micrometers in fitted black vinyl case.
Almost certainly made for them by the Central Tool
Co. Friction / ratchets and locks; and generally along
the lines of the “Apprentice” micrometers.

$35 donation

Item #391
Sears Craftsman 0-1” micrometer made by
Scherr-Tumico.
Satin chrome frame, .0001” vernier, ratchet, lock, and
decimal equivalents. Good quality micrometer in
good condition. This will have had ground threads.

$30 donation

Item #392
Sears Craftsman Commercial 0-1” micrometer
made by Scherr-Tumico. All satin chrome, carbide
faces, ratchet, .0001” vernier, decimal equivalents, and
lock. Top of the line. Example “A” in a clear front vinyl
case.

$35 donation

142
Item #393
Sears Craftsman Commercial 0-1” micrometer
made by Scherr-Tumico. All satin chrome, carbide
faces, ratchet, .0001” vernier, decimal equivalents, and
lock. Top of the line. Example “B” without a case and
signs of use (but no non-original markings).

$25 donation

Item #394
Sears Craftsman 0-1” micrometer in blue card-
board box (marked No. 4090) and made for them
by the Central Tool Co.
Painted frame marked “FORGED STEEL” with friction
“ratchet” and lock. The thimble would clean up a bit
with a brass brush.

$20 donation

Item #395
Sears Craftsman 0-1” micrometer in black
leatherette case, made in Germany.
Nice made of heavy construction, all satin chrome,
with a ratchet and lock. The Craftsman logo of is the
1970’s style.

$35 donation

Item #396
All satin Sears Craftsman 0-1” micrometer with
full satin chrome frame, vinyl pouch case, origi-
nal cardboard box and paperwork.
Model #40691 as appears in the 1960 Hand Tools cata-
log. The best micrometer they sold at that time, fea-
tured on the front cover of the catalog, and made for
them by the Central Tool Co.

$35 donation

143
Item #397
Sears Craftsman 0-1” micrometer with wrinkle
black frame and original box marked #38601.
Made for them by Scherr-Tumico with a ratchet and
lock. Near mint condition.

$25 donation

Item #398
Sears Craftsman 0-1” mechanical digital mi-
crometer made for them by the Central Tool Co.
In very good condition with carbide anvils, satin
chrome finish, a friction thimble and lock. I would
guess it to be mid to late 60’s

$45 donation

Item #399
Sears Craftsman Commercial 0-1” micrometer
with black wrinkle frame, vinyl tool pouch, and
original box marked #38624.
Includes ratchet, lock, and an effective but cost-reduced
calibration (set screw to spindle). Made for them by
Scherr-Tumico, with a ratchet and lock. While this
is a nicely made micrometer in mint condition, such
features as the screw-type lock and the lack of a vernier
really don’t merit the “Craftsman Commercial” name.
Confusion at Sears . . .

$30 donation

Seidensticker
(Oakland, U.S.A.)
Item #400
Seidensticker 4.5 to 7 pitch 0-1” thread microm-
eter.
Robust frame design with speeder and lock. The “Se-
idensticker” name and “Oakland – U.S.A” descriptions
stand out from the wrinkle black frame.

$30 donation

144
Shardlow Micrometers, Ltd.
(Sheffield, England). Also known as Ambrose Shardlow & Co. Ltd. I believe the company was founded
in 1869 based on this entry in the UK National Archives: http://www.nationalarchives.gov.uk/a2a/re-
cords.aspx?cat=1448-mnas&cid=-1#-1 A huge workshop was active in a wide variety of manufacturing
(especially crankshaft’s, including for the Spitfire) during WWII and thereafter. Apparently they began
manufacturing micrometers for their own use, perhaps seeing scarcity during the war, and also devel-
oped a metric version for sale abroad. The company was taken over by GKN in 1963. At some point,
Shardlow’s micrometer business was acquired by the Neill Tools Group (see the Moore & Wright entry).

Item #401
Ambrose Shardlow & Co. (Sheffield, England)
0-1” micrometer.
Carefully made, with a somewhat unusual lock mecha-
nism.

$40 donation

Item #402
Unique Shardlow 0-1” / 0-25mm micrometer
in belt hook case, complete with spanner inside the
case. An innovative (if somewhat hard to read) inch-
metric micrometer. Note the dual scales on the barrel
and thimble. Also includes a unique (but more expen-
sive to manufacture) and effective spindle lock. Well
made, with ratchet thimble. A version of this microm-
eter was made for Regal Beloit and likely others.

$35 donation

145
J. T. Slocomb Co.
J.T. Slocomb Co. (Providence, R.I.) was established a graphic trademark on catalogs and correspon-
in 1891 by John Tibbets Slocomb. His first inven- dence with a micrometer measuring the globe and
tion and product was a center drill; a type still the tag line “Slocomb micrometers are used all over
commonly used today. the world.” The company was then competing for
Slocomb writes that the first micrometer he ever third place or fourth market share at that point, be-
saw, in 1884, was made by A. J. Wilkinson – an hind Starrett and Brown & Sharpe.
example of which is in this collection. He then
worked briefly at Brown & Sharpe before inventing Slocomb sold the company to J.H. Drury (sales
“the longest lived micrometer that can be bought.” manager of Union Twist Drill) in 1914. Drury in-
His first micrometer was produced in 1893. corporated the firm as J.T. Slocomb Co. Edward
Blake, Jr. is listed as General Manager in Catalog
Slocomb was all about function – he defended #14 from about that time (1915). However, Ken-
his black painted frames in a “Machinery” article neth Cope (in his excellent “Maker’s of American
(which were mistaken for cast iron rather than Machinist’s Tools”) says that Slocomb was kept on
forged steel) while others were polishing theirs. as General Manager. Catalog #15 no longer lists
Instead, he talked about the special lathe he built anyone as General Manager.
to make precise micrometer screws, and the larger
spindle and high quality tool steel he used. Slo- The company introduced the “Davenport-Slocomb”
comb also felt that spindle locks weren’t necessary mechanical digital micrometer in 1920; based on
for micrometers – that they would just encourage its Davenport’s 1916 patent. A patent tubing microm-
use as a fixed gauge rather than a measuring instru- eter was introduced in 1917. A duplex micrometer
ment. for gauging was introduced in 1921. There are ex-
amples of each in the collection.
Many precision tools at the end of the 19th and be-
Court documents suggest the company was large-
ginning of the 20th centuries still relied on some
ly unprofitable from 1944 until it went in receiv-
custom fitting. Slocomb highlighted his use of “Jo
blocks” (see Johansson) and other high precisionership in 1952. The company was sold in 1953,
along with its micrometer-making jigs and fixtures,
tools to achieve truly interchangeable parts. His
best known invention is a two-piece adjustment and its manufacturing operations moved to South
Glastonbury, CT. The “SpeedMike” (a digital me-
nut with a spring in between. The overall effect of
chanical micrometer) was one of the featured tools
all these design and process elements was a long-
wearing micrometer. Many century-old examples in the new facility; and also sold under other brand
remain accurate today. names, including, Central Tools, Moore & Wright,
and Snap-on. It looks to be the same design as the
By 1915, perhaps earlier, the company was using 1916 patent.

Item #403
J. T. Slocomb 0-1/2” ball anvil micrometer, bear-
ing the 1896 and 1897 patent dates on the thim-
ble.
This wonderful small micrometer has a cut-away frame
(tube micrometer) allowing its use within tubing as
well as normal measurements. Overall excellent con-
dition.

$40 donation

146
Item #404
J. T. Slocomb 0-1/2” ball anvil micrometer, bear-
ing the 1896 and 1897 patent dates on the thim-
ble.
Same as above, with some paint loss (easily fixed) and
clean and sharp markings. Same cut-away frame.

$38 donation

Item #405
J. T. Slocomb 0-1/2” ball end anvil and spindle,
with friction speeder at end and 1896 and 1897
patent dates.
This doesn’t have the cut-away frame of the others and
may have been a special order for the double ball end
arrangement. Good condition considering its age.

$40 donation

Item #406
J. T. Slocomb 0-1” ball anvil tubing micrometer
with a cut-away frame.
Somewhat later manufacturing date; lacking the en-
graved patent dates.
$30 donation

Item #407
J.T. Slocomb 0-1” standard design micrometer
with friction speeder at the end.
Includes the 1896 and 1897 patent dates, along with
decimal equivalents, on the thimble.

$20 donation

147
Item #408
J.T. Slocomb 0-1” standard design micrometer
with plain thimble.
Still has the smooth drag that Slocomb mics are know
for – due to the split and spring-loaded adjustment
screw.

$15 donation

Item #409
Slocomb 0-1” micrometer with forged frame and
pressed decimal equivalents, first introduced in
1903.
Slocomb may have vigorously defended his plain black
enameled frames; but he also produced one of finest
looking polished frames made. These were forged,
then followed by a 300 ton stamping press to raise the
decimal equivalents. This mic, possibly a century old,
is in excellent cosmetic and working condition.

$40 donation

Item #410
J.T. Slocomb 0-1” micrometer with forged frame
and pressed decimal equivalents.
Includes 1896/97 patent dates, with the main differ-
ence being the desirable and somewhat uncommon
addition of a friction thimble. Looks and works well.

$45 donation

Item #411
J. T. Slocomb 0-1” micrometer with forged
frame, pressed decimal equivalents, plus a fric-
tion speeder at the end.
Includes the 1896/97 patent dates. Same polished
frame as above, with the 300 ton stamping to raise the
decimal equivalents. There is a small, lightly, and neat-
ly engraved inscription dating this mic to an owner in
Lubec, Maine, 1923. Excellent working condition.

$40 donation

148
Item #412
J. T. Slocomb 14-20 pitch and 0-1” capacity
thread micrometer.
Note the anvils. This has the desirable frame with
pressed decimal equivalents and the 1896/97 patent
dates. This is probably the most common thread range
many will use (I made lots of ¼-20 threads for camera
mounting equipment and it will also handle 5/16, 3/8,
and 7/16 NC threads). Very good cosmetic and work-
ing condition micrometer.

$35 donation

Item #413
J.T Slocomb 8-13 pitch and 0-1” capacity thread
micrometer.
Excellent condition, all-satin chrome finish from the
Glastonbury era.

$25 donation

Item #414
J.T. Slocomb 0-1” direct reading (mechani-
cal digital) micrometer, introduced nearly 100
years ago.
Fairly uncommon mic, in excellent condition. The
Davis-Slocomb 1916 patent date is pressed into the
frame, along with the decimal equivalents. The case is
not original; but for protection.

$100 donation

Item #415
Slocomb mechanical digital depth micrometer
with a streamlined look.
Sold to me by Lionel, with his neat cursive mark on
one side.

$30 donation

149
Item #416
J.T. Slocomb 0-1” all chrome micrometer.
Glastonbury (later) era in excellent condition.

$30 donation

Item #417
J.T. Slocomb set of three micrometers in original
fitted black velvet lined box.
Includes 0-1” with polished frame and decimal equiva-
lents, and standard 1-2” and 2-3” micrometers. All
have the 1896/97 patent dates and adjustment instruc-
tions are included. A nice set – usable and collectible.
Duel at .001” paces.

$100 donation

Item #418
J. T. Slocomb set of four micrometers, 0-1”, 1-2”,
2-3”, and 3-4” capacities.
Good measuring condition, but with worn paint on the
frames and no cases. A bargain for use.

$75 donation

Item #419
J.T. Slocomb set of four micrometers in original
two-tier fitted box.
All four micrometers have a black enamel frame,
speeder / friction thimbles and roll type locks. Set in-
cludes standards and adjustment instructions. Col-
lectible and usable.

$100 donation

150
Item #420
J. T. Slocomb fly type tool micrometer with
1896/97 patent dates.
Similar micrometers are meant for setting boring bars
and fly cutters prior to use. The graduations reflect
twice the actual spindle measurement, since a bored
out hole in a lathe will get twice as large as the move-
ment of the cutting tool (it cuts both sides of the bore).
This may have been a special order; since other fly type
tools had V anvils without the added precision of hard-
ened anvil pads. This can stand upright on a desk,
holding the cylindrical object of your own desire. Re-
store the bright bits and paint??

$40 donation

Item #421
J. T. Slocomb 0-1” and 1-2” SpeedMikes.
These are near new condition mechanical digital mi-
crometers. The 0-1” micrometer is all satin chrome in
its original plastic case. The 1-2” micrometer is the
same satin chrome thimble design, with a blank wrin-
kle frame. Both have a .0001” reading vernier. This is
a significantly more streamlined design than the Mitu-
toyo and NSK mechanical micrometers, with a heritage
that dates back to the original Davis-Slocomb patent.

$140 donation

Item #422
J. T. Slocomb 0-2” marked micrometer with
three interchangeable anvils to cover a range
that looks to be up to 2.5”
These are from Slocomb’s Glastonbury days and have
an unusual interchange design that looks to be accurate
and repeatable. Clean micrometer with just the slight-
est wear to the paint.

$35 donation

151
Item #423
J. T. Slocomb 0-1” snap gauge micrometer with
double spindles.
This one is in poor cosmetic condition with one re-
placed locking screw, but the chrome is clear and it
looks to be accurate. Not hard to restore the wrinkle
black paint if you want cosmetic perfection; and usable
as is.

$60 donation

Item #424
J. T. Slocomb 1-2” snap gauge micrometer with
double spindles.
This is free of previous owner’s markings (somewhat
rare for a gauge); from the earlier Providence factory.

$65 donation

Item #425
J. T. Slocomb large (8-9”) snap gauge microm-
eter.
I wouldn’t trust this for accuracy, but it looks pretty
cool. Put it in a micrometer stand and give it to a
doctor friend. That way, they’ll always have a second
opinion right at hand.

$50 donation

Item #426
Slocomb 0-1” x 3” deep throat mechanical digi-
tal micrometer with digits to .001” and a .0001”
vernier.
Glastonbury made. Faint control number marked on
the thimble. Needs adjustment, possibly recondition-
ing, and a new coat of wrinkle black paint.

$20 donation

152
Item #427
J. T. Slocomb 2-3” by 6” deep throat micrometer.
Glastonbury marked with black wrinkle frame. Mea-
sures features that can’t be reached by ordinary mi-
crometers. Unlike horse shoes, these need not be hung
open side up for best luck. Very good condition.

$70 donation

Item #428
J. T. Slocomb 3-4” by 9” deep throat micrometer.
Glastonbury marked with black wrinkle frame and a
match to the 2-3” size above. This one’s just bigger,
deeper. There’s a Watergate etc. joke somewhere here
about deep throat micrometers, which we’ll leave to
you. Very good condition.

$80 donation

Sonoike Manufacturing Co.

is (according to a Mitutoyo history of the micrometer), the first Japanese company to make a microm-
eter. The company had two main parts; one making machine tools and the other small tools. Their 1918
micrometer prototype was based on C.E. Johansson’s mode and by 1921 the company was exhibiting
micrometers at a Japanese machine tool show.
Item #429
Sonoike 0-25mm micrometer marked “Sonoike
Tokyo.”
This is of a completely conventional design – almost
identical to some German exports for example – but
made to a high standard. Someone at COFES may
be able to decipher the paperwork affixed to the lid –
which appears to be a detailed inspection report.

$30 donation

153
Sorensen Center-Mikes, Inc.
(Bridgeport, Conn). Makers of an ingenious device to measure the distance between hole centers to
.001”

Item #430
Sorensen Center-Mike to measure hole centers
from .24 to 7.4” apart.
In wood box with instructions and advertising bro-
chure. Likely late 50’s to 60’s. An unusual but still
useful tool

$50 donation

Standard
brand; as sold by Majestic Tool & Hardware Co. of Chicago, IL. The same unknown manufacturer made
a mic with a Chicago brand decal. The frame design looks to be copied from Slocomb. Cheap import?
US?

Item #431
“Standard” brand 0-1” micrometer with black
painted frame and cardboard box marked Ma-
jestic Tool & Hardware Co.
Low cost mic (poorly made) from an unknown maker.
The first wave of really cheap imports? A US manu-
facturer?

$10 donation

Item #432
“Standard” brand 1-2” micrometer with black
frame and slightly fancier knurled thimble.
Decal is largely missing.

$10 donation

154
Item #433
“Standard” brand 0-1” and 1-2” micrometers
with slightly fancier knurled thimbles.
$20 donation.

Item #434
“Chicago” brand 0-1” mic with the slightly fancy
thimble, as above.
$10 donation

155
L. S. Starrett Co.
L.S. Starrett Co. (Athol, MA) was founded in 1880 acquired the Athol Machine Co. in 1905.
by Laroy S. Starrett (1836-1922). Starrett received
early patents for a food chopper (1865; without By Catalogue No. 13 (1895) Starrett was making
the “it slices, it dices . . .” tag line), a washing ma- his #3 “speeded screw” micrometer – examples of
chine, and a food press (1873). The food chopper which are in the collection.
and press were later made by the Athol Machine Co. Beginning around 1902 (Catalogue #16) or earlier,
By 1876 he invented the combination square – in a Starrett tools have been marked with “L. S. Starrett
form which is still dominant today. Foreshadow- Co.” rather than “L.S. Starrett.” A old tool without
ing today’s patent battles, Starrett had a massive the “Co.” is likely from the late 1800’s.
battle with former associates of the Athol Machine
Co. over his combination square patent. Starrett Starrett now has manufacturing facilities in the US,
prevailed, at a cost, and saw patent strategy as a key Brazil, the United Kingdom, and China, with an-
to competitive success for the next several decades. nual sales around $250 million.
As a measure of his competitiveness, Starrett later
Item #435
#3 Starrett 0-1” micrometer with May 4, 1897
and Dec. 5, 1906 patent dates; protected in a
now-worn Starrett case.
In excellent condition for its age.

$50 donation

Item #436
#3 and #217 Starrett 0-1” and 1-2” micrometers;
looking great for centurions.
Both have the old three knurl thimble and front lock;
with 1890, 1891, and 1897 patent dates on the frame.
The 1” is slightly newer vintage with a (slipping) ratchet
and a 1900 patent date on the end of the thimble. The
2” has a plain thimble, made prior to the 1900 patent.
No extra markings – very good condition for their age.

$75 donation

156
Item #437
#2 Starrett 1-2” micrometer with old patent
dates.
All polished steel with a ratchet and lock. This has
1880, 1881, and 1897 patent dates on the frame and a
1900 date on the end of the thimble. Three knurls on
the thimble. A perfect mate to one of the century-old
#3 micrometers below; in very good condition.

$60 donation

Item #438
#2 Starrett 1-2” micrometer with patent dates of
May 4, 1897 and Dec. 10, 1907 stamped on the
back.
Good condition with all the usual #2 features for the
time.

$35 donation

Item #439
#2 Starrett 1-2” micrometer plus a #212 anvil ex-
tension for a range of 0-2 inches.
Frame has decimal equivalents and a December 30,
1902 patent date on the back. Very good condition.

$50 donation

Item #440
#2 Starrett 1-2” micrometer with 1880, 1881,
and 1897 patent dates.
Single knurl on the thimble and no 1900 patent date
suggest a late 1890’s build date. Rare micrometer in
poor condition with pitting (home electro polishing
might help) and deep scratches.

$30 donation

157
Item #441
#T2XFL Starrett 1-2” micrometer. Mint condi-
tion, modern design, in somewhat worn Starrett
clamshell case.
Includes friction thimble, lock, and decimal equiva-
lents on the frame. Factory marked “No. 2” on the
thimble. Stiff spindle from congealed oil – it will ease
up with cleaning and fresh oil. Pair this with a mint
condition #230F or #231-F micrometer.

$70 donation

Item #442
#3 old Starrett “Speeded Screw” micrometer
0-1” with 1890 and 1891 patent dates.
This is one of the first Starrett micrometers (with only
this model and single-knurl thimble type listed in their
1895 catalog No. 13). The “Speeded Screw” reference
is to the small diameter thimble at the back – the first
instance of this useful feature. An auction note is in-
cluded, showing a $295 final price for one example.

$150 donation

Item #443
Unbranded micrometer – but almost surely a rare Star-
rett example given both the very old style Starrett mi-
crometer body and a frame style the company briefly
used (more info under “unknown”)

$?? donation

Item #444
#3 Starrett 0-1” micrometer with old patent
dates.
Similar to the old #220 micrometer elsewhere, but
without the finger hold. This has 1880, 1881, and 1897
patent dates on the frame and a 1900 date on the end
of the thimble. Includes a ratchet and front-side roller
type lock. Old micrometer in original black case.

$60 donation

158
Item #445
#3 Starrett 0-1” micrometer with Dec. 30, 1902
patent date.
All polished steel with ratchet, lock, and decimal
equivalents. Tiny H.G. neatly stamped on the lower
frame. Includes Starrett wood box. We should all
look so good around 110 years old.

$30 donation

Item #446
#3 Starrett 0-1” micrometer with old patent
dates.
Another vintage example, in an old Starrett eyeglass
type case. This has 1880, 1881, and 1897 patent dates
on the frame and a 1900 date on the end of the thimble.
Includes a ratchet and front-side roller type lock.

$60 donation

Item #447
#3 and #226 Starrett 0-3” set in plush fitted black
case with standards.
This is an old set of three micrometers in good condi-
tion. The 0-1” micrometer is an all-steel #3. The 1-2”
and 2-3” have the heavier frames of the #226 series,
ratchets, and locks. Living history.

$100 donation

Item #448
#52 Starrett
surface gage with a patent date of March 21, 1882. The
date is visible around the top part of the collar holding
the scriber. There is a fine height adjustment knob and
lock in the base. The cutout in the circular base allows
the gage to scribe low to the base and, especially, to be
used as a depth gage. This is how parts were laid out a
century or more ago.

$35 donation

159
Item #449
#52 Starrett
surface gage in a larger size, probably dating from
around the 20’s. The Starrett name is inscribed on the
spindle about 5” up from the base. Note the fine height
adjustment knob. The cutout in the circular base allows
the gage to scribe low to the base and, especially, to be
used as a depth gage. Nice shape, still quite usable.

$30 donation

Item #450
#86 (though not so marked) Starrett 0-1” U.S.
standard sheet micrometer and weight indica-
tor.
The #86 designation appeared around 1900. This has
Starrett’s oldest style thimble (a single narrow knurl)
and dates from the 1890’s. It includes a stamped iron
sheet gauge on the front side of the frame and 1890 and
1891 patent dates on the rear side of the frame. An old
a rare micrometer in remarkably good condition for its
age.

$150 donation

Item #451
#124 Starrett inside micrometer (very common)
and a #447 (somewhat rare) mount to convert it
to a height gage.
Includes 9 extension rods and a half inch spacer to
cover a range up to 12” inside or height measurement.
For height measurement, the #447 attachment is used
on a flat surface plate. See the Lufkin listings for the
same idea, executed with even more flair. The #124 is
in good condition, with a slight tarnish on some rods
and one rod (8-9”) missing. The #447 attachment is in
very good condition

$65 donation for both kits

160
Item #452
#127 Starrett “United States Government mi-
crometer gage” with interchangeable anvils, a
capacity from 4 – 8”, and its original fitted oak
wood case.
These first appeared around 1902. “These gauges are
designed to meet the requirements of the Government
in making big guns and other work in the Ordnance
Department . . .” The nicely designed frame is covered
by a hard rubber – predating the age of plastics. The
thimble type and absence of a “127” marking suggest
this one was built around 1905.

$150 donation

Items #454 to 456

#128 Starrett six inch micrometer calipers.
Despite three examples, this is a fairly uncommon micrometer. All three include a front locking mi-
crometer head (dating from about 1900 on). The idea of this tool was to provide the range of calipers
with the precision of a micrometer. The beam has precisely located holes, allowing the head to be set at
one inch intervals. Typical eBay prices on these have been around $200 (e.g. $216.06 on 10/30/02 and
$237.50 on 5/17/2003).

Item #454
#128 Starrett six inch micrometer caliper, neatly
engraved “The Crosby Co.”, with patent dates to
1897 lightly stamped on the rear of the frame.
This one likely dates from 1902-1905. It has a thimble
style seen around 1902, but doesn’t have the front side
company that show up in Catalog #18 (circa 1905).

$135 donation

Item #455
#128 Starrett six inch micrometer caliper likely
dating from near the end of World War II (it has
the inch markings on the beam, that are first
shown in Catalog #22).
Somewhat rough condition (though no owner mark-
ings); but an example of an uncommon type.

$85 donation

161
Item #456
#128 Starrett six inch micrometer caliper.
I’d estimate this one from around the 1920’s. It looks
to still be accurate within the limitations of the design.
The L.S. Starrett Co. logo is shown on the fixed anvil
end of the beam.

$100 donation

Item #457
#175 Starrett 0-2” Inspector’s Micrometer with
ratchet, lock, standard, and two curved anvils;
all in original black fitted case.
This is meant to insert in plug holes to inspect the
thickness of boilers and pressure vessels. A clever
idea. New cost on these is $759 (Amazon.com). Giv-
en ASME’s corner on pressure vessel standards, a must
for ME’s!

$100 donation

Item #458
#202 Starrett 0-1” micrometer with old patent
dates.
Similar to the very old #3 micrometers elsewhere, but
without a cut-away frame or front lock. This has 1880,
1881, and 1897 patent dates on the frame and a 1900
date on the end of the thimble. Includes a ratchet and
decimal equivalents on the frame.

$55 donation

Item #459
#203 Starrett 0-1” micrometer in original black
leather covered case.
Pretty simple. No ratchet, no lock, just decimal equiv-
alents. First mic I owned, first year in college.

Gone to a college friend

162
Item #460
#205 Starrett steel mill micrometer 0-1” with
heavy all-satin chrome frame with decimal
equivalents, a large thumb lock, large numbers,
and a handle.
This type first appeared with catalog #26A around
1938. Just in time for our growing steel industry. This
example is in near mint condition, but with chipping to
the paint on the handle. No reason it won’t work fine
for ordinary .001” measurements.

$100 donation

Item #461
#205 Starrett steel mill micrometer 0-1” with
heavy all-satin chrome frame with decimal
equivalents, a large thumb lock, large numbers,
and a handle.
This type first appeared with catalog #26A around 1938
(just in time for our growing steel industry). This ex-
ample is fairly good used condition, but with an identi-
fier (“HM1”) etched into the rear of the frame. Includes
handle. The method of handle attachment is different
from the above; with a screw through the handle and
into the frame – it may have been an early design, later
abandoned?

$65 donation

Item #462
#205 Starrett steel mill micrometer 0-1” with
heavy all-satin chrome frame with decimal
equivalents, a large thumb lock, and large num-
bers.
This one is missing its handle, but is in otherwise very
good condition. The type first appeared with catalog
#26A around 1938. Fit your own desktop stand?

$50 donation

163
Item #463
#207 Starrett 0-1” micrometer, all polished steel
with a center roll lock, a .0001” vernier, and a
June 2, 1914 patent date stamped into the back
of the frame.
A style commonly used for WWI production; that still
looks to be in good condition.

$45 donation.

Item #464
#207 Starrett 0-1” micrometer with a front side
lock and a .0001” reading vernier.
Lightly tarnished and scratched, but still personable
and accurate. This one is a bit of a puzzle. Catalog
#17 (1903) is the last one to show the #207 with a front
side lock. However, the thimble is of a later type. Per-
haps—a testament to interchangeable parts—it was
switched along the way? The #207 was retired, and
later used for can seam micrometers.

$20 donation

Item #465
#207/208 -style “can seam” micrometer in stain-
less steel.
Tiny Starrett micrometer head (with no model num-
ber stamped) and a specialized anvil for measuring the
seams on beverage cans. Marked with the “Canco” (the
American Can Company) logo near the anvil. Canco
itself went from being a part of the Dow Jones Indus-
trial Average to being a part of history. This mic is in
mint condition in a Starrett cardboard box. It would
also work as a wire micrometer.

$45 donation

164
Item #466
#209-F (and C) Starrett 0-1” micrometer with
all-satin frame, decimal equivalents, friction
thimble, and .0001” vernier.
Also includes the cut-way frame, often designated “C.”
This is another vintage micrometer where Starrett has
retired the number and later reused it (for a “Can Curl”
micrometer). Near mint condition, in Starrett card-
board box.

$40 donation

Item #467
#210-A Starrett 0-1” point micrometer.
For thread comparisons and small grooves (compare
to Lufkin No. 1911 C).

$25 donation

Item #468
#210-A Starrett 0-1” point micrometer.
Nice shape, but with slightly tarnished pads and a
frame (nicely) modified to fit in even tighter spaces.

$25 donation

Item #469
#211 Starrett 0-1” ball anvil micrometer; reach-
es into holes as small as 5/8 of an inch.
Satin chrome thimble with decimal equivalents. In-
cludes red Starrett #910 clamshell case. New, they’re
around $125 without the case. This is like new.

$45 donation

165
Item #470
#212 Starrett anvil attachment for two inch mi-
crometers; in original cardboard box.
Converts Starrett 2” micrometers to 0-1” reading.
Near mint condition.

$30 donation

Item #471
#212 Starrett anvil attachment for two inch mi-
crometers in used condition.
Converts Starrett 2” micrometers to 0-1” reading. Buy
one of the older Starrett 2” micrometers and have it do
double duty.

$20 donation

Item #472
#212 anvil extension and #2RL micrometer; for
a combined 0-2” range.
Satin chrome, with a center roll lock, ratchet, and deci-
mal equivalents on the frame; all in original black plush
fitted case. The #212 idea goes back to about 1900, but
this is a more recent vintage in excellent condition.

$65 donation

Item #473
#213 Starrett 1-2” micrometer with an old style
front locking nut and a single knurled thimble.
Essentially the same as an early #2 Starrett, with the
addition of a .0001” reading vernier. Worn look on the
back side of the frame; otherwise good.

$30 donation

166
Item #474
#215 Starrett 0-1/2” micrometer with ratchet
and decimal equivalents.
Missing the knurled lock nut.

Free to the first person who anyone who:

• 1) Buys more than $300 of mics. and
• 2) Plans to learn how to knurl on a lathe

Item #475
#216 Starrett 0-1/2” micrometer; predecessor
the #232 model.
Has a ratchet and decimal equivalents. Starrett retired
the number and later used it for their mechanical digi-
tal micrometers. A bit of tarnish and wear, but overall
very good.

$35 donation

Item #476
#216 Starrett 0-1” mechanical digital microm-
eter.
Recent ones have a cost-reduced painted frame. This
has the earlier (sleek!) all-satin chrome design. New
condition in its cardboard box, clamshell case, and pa-
perwork. Includes a friction thimble and lock.

$90 donation

Item #477
#217-C Starrett 1-2” micrometer in excellent
condition.
Bright steel with center roll lock and decimal equiva-
lents on the frame. The included 1” Starrett standard
shows it to be right on. Right on! Good match to an
earlier (no chrome for us) Starrett 0-1” mic.

$30 donation

167
Item #478
#220 Starrett 0-1” micrometer with finger-hold-
ing ring in original case.
This has the old style thimble with three knurled bands,
plus 1880, 1881, and 1897 patent dates on the frame
and a 1900 date on the end of the thimble. Includes
ratchet and front-side roller type lock. The number
220 was retired and then later used for Mul-T-Anvil
micrometers. Uncommon mic due to both the age and
the finger hold. A 12/24/02 auction price for an identi-
cal mic was $156.62.

$80 donation

Item #479
#220 Starrett 0-1” micrometer with finger-hold-
ing ring.
This has 1897 patent dates on the frame and a 1900
date on the end of the thimble. It will be slightly newer
than the example above. Note that the number 220
was retired by Starrett for a while and then later used
for Mul-T-Anvil micrometers. Uncommon mic.

$65 donation

Item #480
#220 Starrett 0-1” special (Braille) Mul-T-Anvil
micrometer in original cardboard box.
These multiple anvil micrometers allow special anvils
to be inserted. Pins, for example, can reach into tubes
and holes. A flat anvil can measure grooves to shoul-
ders. What’s rare about this one is that the graduations
are all in Braille. This surely beats the usual motiva-
tional poster hanging on corporate walls?

$80 donation

168
Item #481
#T221XL Starrett Hi-Precision micrometer.
This unusual micrometer measures directly in .0001”
and uses a constant pressure system for accurate and
repeatable measurements. New cost is $363 (Ama-
zon.com). This one is in mint condition in its origi-
nal cardboard box. A somewhat older vintage with a
patent number on the reverse side of the satin chrome
frame.

$95 donation

Item #482
#T221XL Starrett Hi-Precision micrometer.
This unusual micrometer measures directly in .0001”
and uses a constant pressure system for accurate and
repeatable measurements. New cost is $363 (Amazon.
com). Mint condition in its original modern eyeglass
type case.

$105 donation

Item #483
#222 Starrett 0-1” by 6” deep throat micrometer
with a ratchet.
Reaches deep into sheets as well as regular measure-
ments. The original and beat up fitted black case looks
to have kept the micrometer, it’s older style (decimal
equivalents) satin chrome thimble, and wrinkle black
painted frame in pristine condition.

$70 donation

Item #484
#223 Starrett 0-1/2” paper gauge micrometer
with ratchet, lock, and decimal equivalents in
#921 Starrett clamshell case.
Includes finger hold. All in very good condition.

$70 donation

169
Item #485
#223 Starrett 0-1/2” paper gauge micrometer
with ratchet, lock, and decimal equivalents.
Worn but working, with the interesting finger hold.

$25 donation

Item #486
#224-A Starrett 2-6” interchangeable anvil set
in original oak case.
Overall good condition with all four anvils and four
standards. A good way to extend one of the many
1-2” sets.

$65 donation

Item #487
#225 Starrett 0-1/2” vintage paper micrometer
with wide anvils.
Mint condition in small hinged black leather case. In-
cludes ratchet, lock, and decimal equivalents on the
frame. This has been superceded by the #223 paper
micrometer, with the #225 number going to wire mi-
crometers.

$100

Item #488
#225 tiny Starrett micrometer 0-.5” with 1890-
1897 patent dates engraved.
This is a fairly rare mic; but bit of a project – turning
an anvil to fit.

$25 donation

170
Item #489
#226 Starrett 1-2” micrometer two pack. One
has the plain steel and the other a satin chrome
thimble.
Something old, something new. Both are in good
shape; but there is only one front lock nut to share be-
tween them. Put it on whichever mic you want.

$30 donation for the pair

Item #490
#226RL Starrett 1-2” micrometer with steel
thimble; user modified for the blind.
This was custom machined with added elements. It’s
unclear if this is an early Starrett special or user modi-
fied. Compare to the other #226 Braille version, which
has different elements for reading. People rise to meet
the challenges facing them.

$70 donation

Item #491
#226RL Starrett 1-2” micrometer with satin
chrome thimble; Starrett special for the blind in
original cardboard box.
This was a custom order Starrett item, manufactured
after the other example. The system of markings is
consistent with the “Special” #220 Braille micrometer
listed elsewhere.

$70 donation

Item #492
#226 Starrett 1-2” and 2-3” micrometers with
ratchets, locks, and 1891 and 1897 patent dates
on the rear pads.
These have the desirable heavier frame style and are
in very good condition; even disregarding their age.
Mate them to a 0-1” Starrett for a micrometer set that
has both history and accuracy on its side.

$65 donation

171
Item #493
#226 Starrett 0-6” micrometer set with carbide
anvils, ratchets, and locks.
These are in a B&S case. These have a stronger and
heavier weight frame than Starrett’s ubiquitous #436
series. The 0-1” mic is an all-chrome #230. Both it
and the 1-2” mic have .0001” verniers. The chrome
is pretty much flawless; while there are minor flaws to
the paint. Note the clip-over pieces which are non-
original. Overall, a nice set in a fitted velvet lined case,
which while non-original, beats cardboard boxes.

$195 donation

Item #494
#228 Starrett 0-1” hub micrometer; all-satin
chrome with ratchet and roller type lock.
Includes original red Starrett snap case. Designed to
reach into areas such as pulley, wheel, and gear hubs;
but works fine for any measurement within its depth.
An engraving on the back has been covered with
chrome tape. Compare this to the #263 micrometer
head mated to a hub frame.

$35 donation

Item #495
#T230RL Starrett 0-1” micrometer with all satin
chrome frame, decimal equivalents, a ratchet,
and lock.
Reads to .0001” and is in very good condition. Nice
mic.

$30 donation

Item #496
#T230RL Starrett 0-1” micrometer with all satin
chrome frame, decimal equivalents, a ratchet,
and lock.
Reads to .0001” and is in very good condition. In-
cludes black Starrett leatherette case.

$35 donation

172
Item #497
#T230XFL Starrett 0-1” micrometer. Mod-
ern design with friction thimble, lock, all satin
chrome, .0001” vernier, carbide anvils, and deci-
mal equivalents.
Stamped No. 230 on the thimble. Pair this with the
#T2XLF in a red clamshell case. Near mint condition
in original cardboard box.

$55 donation

Item #498
#231 Starrett 0-1” micrometer – predecessor to
the same-featured and looking #230 but with an
all steel finish.
These older #231 models have a slightly more pro-
nounced cut away frame (for reaching tight spots).
This one is faintly scratched or marked in several plac-
es; but the ratchet, lock, and spindle all work fine. #1
example. New versions of this micrometer have added
thermal pads.

$20 donation

Item #499
#231 Starrett 0-1” micrometer – predecessor to
the same-featured and same looking #230 but
with an all steel finish.
Same as the #1 example, but somewhat brighter and
better condition. Call this the #2 example.

$25 donation

Item #500
#231 Starrett 0-1” micrometer with all-satin
chrome frame with decimal equivalents, a ratch-
et, lock, and .0001 vernier.
Very nice, but with the faintest inscription on the back.

$30 donation

173
Item #501
#231-F Starrett 0-1” micrometer. Modern de-
sign with friction thimble, lock, all satin chrome,
.0001” vernier, and decimal equivalents.
An excellent pair to the #This model number (stamped
No. 231-F on the thimble) has since been superceded
by #230. Near mint condition in original cardboard
box.

$55 donation

Item #502
#232 Starrett 0-1/2” micrometer. Identical to
those below (T232RL) except a slightly older
(better?) vintage with all satin chrome for even
the ratchet and lock.
Mint condition in older Starrett cardboard box.

$75 donation

Item #503
#232 Starrett 0-1/2” micrometer.
Identical to later T232RL mics; but bright chrome all
over. Good condition; lock ring needs work.

$35 donation

Item #504
#T232RL Starrett 0-1/2” micrometer. Like new
in original cardboard box – a great gift.
Tiny mic includes a ratchet, lock, and .0001” vernier.
May have a stiff action from sitting.

$75 donation

174
Item #505
#T232RL Starrett 0-1/2” micrometer. A second
mint condition micrometer in original card-
board box.
Last person I gave one of these to has turned into an
extremely gifted architect, specializing in LEED cer-
tified design. Tiny mic includes a ratchet, lock, and
.0001” vernier.

$75 donation

Item #506
#T232RL Starrett 0-1/2” micrometer.
A fourth #232 micrometer in excellent condition. No
box. These tiny mics fit anywhere from a pocket to an
auto ashtray to a purse. Justify a man-purse? Fit it to
a necklace for a bold fashion statement?

$55 donation

Item #507
#T232RL Starrett 0-1/2” micrometer.
Like those above, but with slight signs of use and no
case. Tiny mic includes a ratchet, lock, and .0001” ver-
nier.

$45 donation

Item #508
# 234 Starrett micrometer calibration standards.
There are two 5” (for up to 5-6” mics), two 4” (for 4-5”
mics, you get the idea, two 3”, four 2”, The 1” usually
runs around $20 new; going up a bit in cost with larger
lengths. If you want to be able to check and adjust –
and your mic doesn’t have one included . . .

$7 donation each

175
Item #509
#238RL Starrett heavy duty 0-1” micrometer
with all satin chrome, ratchet, lock, and decimal
equivalents on the frame.
This is designed for heavy work, such as grinding or
when using the micrometer with the lock fixed. De-
sired by some due to its heft, reliability, and relative
scarcity. Near mint condition in original cardboard
box with paperwork and adjustment wrench.

$70 donation

Item #510
#263 Starrett 0-1” micrometer head mated to an
shallow frame for use as a hub micrometer.
Hub micrometers are meant to reach into holes (e.g.
pulleys) and measure thickness. Well executed; per-
haps well enough to have been an early Starrett build
of this type micrometer?

$30 donation

Item #511
#436 Starrett 0-1” and 1-2” micrometers.
The Starrett #436 series has been one of the best selling
micrometers over a period of decades. These earlier
examples have the plain steel thimbles with decimal
equivalents, ratchets, and locks. Enamel black frames.
Larger “STARRETT” on the front pad. Everything
(spindle, ratchet, lock) works fine on these, but they
could use paint and polish all around.

$25 donation

Item #512
#436 Starrett 0-1” and 1-2” matched pair.
Older satin chrome spindle (decimal equivalents) and
black enamel frame. Good condition, with slight tar-
nish to the pads and control numbers in the paint. A
good father/son, mother/daughter and other permuta-
tions project to spiff it up like new.

$30 donation

176
Item #513
#436 Starrett 1-2” micrometers (two) showing
product evolution.
Both have older plain steel decimal equivalents thim-
bles. The first example has a deeper frame and “STAR-
RET” on the front pad (with the thimble headed to the
right). The second example has a center roll lock; with
the size and model designation on the “front” and the
Starrett name on the “back.” The paint is damaged on
both.

$30 donation

Item #514
#436 Starrett 2-3” micrometer with the deeper
frame style, decimal equivalents on the plain
steel thimble, a ratchet, and center lock.
Possible addition to matching age #3 and #2 mics.
Checks OK with a 2” standard.

$15 donation

Item #515
#436 Starrett 5-6” micrometer with the older
satin chrome spindle (decimal equivalents),
ratchet, lock, carbide anvils and black enamel
frame.
Very good, save for a bit of tarnish to the pad and
scratches in the paint – both easily fixed.

$25 donation

Item #516
#436 set of six Starrett micrometers 0-6” in Star-
rett wood case.
Mics have satin chrome thimbles with decimal equiva-
lents on them, dark ratchets, bright locking knurls, and
.0001” verniers. Carbide anvils on the two most com-
monly used (1” and 2”) Also includes Starrett stan-
dards within their own wood case.

$395 donation

177
Item #517
#436 Starrett 6-7” micrometer with older satin
chrome spindle (decimal equivalents), ratchet,
lock, and wrinkle black frame.
Perfect to add to the 0-6” set above. Excellent condi-
tion.

$35 donation

Item #518
#436M Starrett 125-150mm micrometer with
rounded anvils, friction thimble, and lock.
Very good condition, with a tiny P-6 in the pad.

$25 donation

Item #519
#436 special 1-2” steel mill micrometer. This
may be an earlier attempt (before 1938) at the
#205 steel mill micrometer or just a larger size
built to order.
It includes a standard Starrett #436 frame with an old-
er style satin chrome thimble with decimal equivalents
on it. The addition is a boss on the frame allowing a
wood handle to be affixed. A complement to the #205
micrometers listed elsewhere.

$60 donation

Item #520
#436 special 2-3” steel mill micrometer.
This is a later version (Starrett decal on the front pad),
with the same spindle and thimble design as the #205
series. It is mated to a #436 style frame with the added
boss, a wood handle, plus a thumb lock. The thimble
is engraved “Special.” This was destined for someone
who wanted a hot and heavy duty micrometer in a larg-
er size. Very good condition, with a tiny inscription in
the front pad.

$60 donation

178
Item #521
#447 Starrett height gage attachment.
for #124 inside micrometer.

Included with Item #451

Item #522
#486-1 Starrett 0-1” blade micrometer in near
mint condition.
Used to measure grooves in shafts. New, they’re $313
(Amazon.com).

$100 donation

Item #523
#569 Starrett 0-1” tubing micrometer.
Rather than the ball anvil type, this has a 3/16” mini-
mum diameter stem. Older style satin chrome thimble
with the decimal equivalents. With original (marked
up) cardboard box. Mic is in near mint condition.

$60 donation

Item #524
#576 Starrett 0-1/2” micrometer with rounded
anvil, satin chrome cut-away frame, decimal
equivalents, and ratchet.
Around $160 new. Very good, near excellent condi-
tion (a ding on the end of the frame).

$55 donation

Item #525
#576 tiny Starrett ball anvil micrometer 0-.5”
As above. Meant primarily for measuring the wall
thickness of tubing and pipe, but suitable for occasion-
al use on flat work as well.

$30 donation

179
Item #526
#650 – see Item #443.
Surely a Starrett, under the “unknown” sec-
tion for what may have been an early prototype
headed towards the #650 style.

Item #527
#733XFL-1 Starrett 0-1” electronic digital mi-
crometer with SPC output.
Includes friction thimble and lock and boasts “Ameri-
can Made” on the rear thermal pad. Newer ones may
now be made in China. Has a sort of Darth Vader-like
design that looks better than the equivalent Mitutoyo;
but the battery life isn’t as good. This is in like new
condition with its red Starrett case and paperwork.

$100 donation

Item #528
#914 “Handy Automotive Service Set” consist-
ing of #224-AA micrometer 0-4” and #452-B
cylinder gage.
Remember when everyone did their own work on cars?
This set likely dates from around 1954. It has the deci-
mal equivalents on the thimble (mostly abandoned for
a knurled thimble by 1955) but the then-newfangled
satin chrome plating. Given the case, it looks to have
been used on at least one engine. The tools, however,
appear have retained their accuracy.

$70 donation

Item #529
#1230 Starrett 0-1” all stainless steel microm-
eter.
The #230 / #231 style of micrometer, but built to be cor-
rosion resistant. Includes a ratchet, lock, and stamped
decimal equivalents on the frame. Mint condition in
Starrett eyeglass-type case.

$90 donation

180
Item #530
#T1230 Starrett 0-1” all stainless steel microm-
eter.
The #230 / #231 style of micrometer, but built to be
corrosion resistant. Includes a ratchet, lock, and
stamped decimal equivalents on the frame. Excellent
condition in soft vinyl case.

$70 donation

Item #531
Starrett “Special” 0-1/2” x 2” deep throat mi-
crometer with pointed anvils.
All satin-chrome with ratchet, lock, and decimal equiv-
alents on the frame. Like new condition in original
cardboard box with paperwork.

$45 donation

Item #532
Starrett “Special” large micrometer with point-
ed anvils, plus a black stand.
My thought was to get a 6-8” world globe and then
place the micrometer with the anvils located at the
poles. Follow the world’s happenings with greater pre-
cision.

$60 donation

Steinmeyer
(Germany); founded by August Steinmeyer in 1920, beginning with the manufacture of high quality
micrometers. The founder died in 1940 and his company acquired after the war, in 1950. August Stein-
meyer’s original house and attached workshop became the starting point for what is now an factory com-
plex on 8 acres. Steinmeyer made a variety of high quality micrometers, but now concentrates on ball
screws. So, the saga of precision screw manufacturing continues. Steinmeyer still makes micrometers,
but at the FMS (Feinmess) Suhl plant in Thuringia.
Item #532
Steinmeyer 0-1” micrometer.
All satin chrome with a ratchet, lock, and decimal
equivalents on the frame. Well made and very good
condition.

$35 donation

181
Item #533
Steinmeyer 0-1” blade micrometer with a stron-
ger frame, spindle, and larger thimble than most
competitors.
Very nicely made with a satin chrome finish, decimal
equivalents on the thimble, a ratchet, and large thermal
pads. These are costly mics, designed for reaching into
groove depths and other tight spaces. Marked as meet-
ing DIN standards. Excellent condition in a Steinmey-
er wood box.

$80 donation

Item #534
Steinmeyer 0-1” Microfix micrometer.
This is a slightly earlier version than the 0-1” mic in-
cluded in another listing with a 1-2” mic. It has a frac-
tion/decimal chart instead of thermal pads. It still
includes both a rapid precision screw (like the much
esteemed Etalon Microrapid) plus a reading window.
Note that this Microfix screw mechanism is the same
as found in an elaborate Polyplan (Geneve) microm-
eter set. A very high quality mic, even harder to find
than the Etalon Microrapid, but not quite as smooth in
operation due to the digital window.
$105 donation

182
Item #536
Steinmeyer 0-1” and 1-2” Microfix micrometers.
This pair of micrometers is a rare “Rolls Royce” sort of
endeavor. It includes both a rapid precision screw (like
the much esteemed Etalon Microrapid) plus a read-
ing window. It includes the fine finish, lock, thermal
pads, and pressure ratchet required of any top quality
micrometer. The 0-1” mic is in mint condition, with
all its paperwork (including a certificate of compliance
with DIN standards). The 1-2” mic came from an-
other source and is well used. It should clean up pretty
well. Judging from the enclosed standard, it also ap-
pears to be in perfect adjustment. Cool, rare, and col-
lectible; with a donation price less than the value of just
the 1” mic. Note that this Microfix screw mechanism
is the same as found in an elaborate Polyplan (Geneve)
micrometer set described elsewhere.

$220 donation

C. Stiefelmayer
(Esslingen, Germany) was founded by Carl Stiefelmayer in 1874 to produce measuring instruments. At
some point it made micrometers, witness our example. The company continues today as a producer of
various 3D metrology instruments and more.
Item #537
C. Stiefelmayer
0-50mm micrometer with original accessory anvil for
0-25mm and a basic frame for 25-50mm. Essentially
two micrometers in one. The accessory anvil idea was
also seen in early Starrett micrometers, more recent
Mitutoyo and NSK micrometers, and others). Includes
ratchet and lock. The frame style is along the lines of
some Brown & Sharpe mics from the early 1900’s.

$40 donation

183
Stoetling Co.
was founded in 1886 as the Chicago Laboratory Supply and Scale Co. It has long supplied psychometric
and other lab instruments.

Item #538
Stoelting/Krieg stereotaxic positioner No. 51200.
Here’s a macabre bit of mechanism; meant for probing
small minds. This is a jig meant for brain stimulus/re-
sponse research with rats. Put it your desk and get the
inevitable “what’s that?” question. Then, watch them
step away unsteadily as you explain . . . This is repeat-
able to .01mm in two axes and 1 degree of rotation.

$100 donation

Sunnen Products Co.

(St. Louis, MO) was founded in 1924. Leaders in a lot of boring (and we mean that in the best manufac-
turing sense) stuff.

Item #539
Sunnen 0-1” large thimble satin chrome mi-
crometer head; made for them by the Starrett
Co.
Reads directly in .0001” coming and going. This wants
to be put to use.

$35 donation.

Supreme
(Germany)
Item #540
Supreme 0-1” micrometer with long speeder /
ratchet (nice design feature – allows use of the
speeder without engaging the ratchet)
with a lock and the typical black fitted case of German
export mics. Nicely made, likely during the time when
Germany was split East and West. It looks to have once
had an applied label with decimal equivalents. See also
the “Unknown 0-1” micrometer with long speeder /
ratchet . . .”

$30 donation

184
Swedish Gage Co.
(Eskilstuna, Sweden) – see also the CEJ (Johansson) company. The Swedish Gage Co. is noted (Google e-
book) in the 1917 Machinery (Volume 23) as having been capitalized under this name. The management
apparently remained the same as C. E. Johansson AB, founded in 1911. Johansson is best noted for the
invention of gage blocks (“Jo blocks”) in 1896; with his first Swedish patent granted in 1901 – an amazing
technical achievement for the time. The first set of gage blocks sold here went the Henry Leland at Cadil-
lac Automobile Company around 1908. Henry Ford made a significant investment in the company; and
Johansson himself moved to Detroit around 1923.

Item #541
Swedish Gage Co. 1 3/8 to 2” bore gage in wood
box, as sold in Detroit.
The patent numbers place this in the early 1930’s. One
of the four supplied “legs” is adjusted exactly to size for
the desired bore size. Measured differences are shown
as plus or .001 and .0001 through a clever dual read-
ing indicator. On each side of the measuring leg there
is a pair of spring-loaded retracting pins to center the
indicator in the bore.

$75 donation

Item #542
Set of 3 Swedish micrometers
(Eskilstuna, Sweden) from the Swedish Gage Co.
These share the standard design features of high qual-
ity micrometers established among most makers by the
early 1920’s or so – a ratchet thimble, a spindle lock,
a .0001 reading vernier and so on. In many ways the
standard micrometers from the US (e.g. Starrett, B&S),
Japan (see the Nachi set), Germany, and the U.K. (e.g.
Moore & Wright) are variants on this theme. Howev-
er, these three have a bit of pedigree. Carl E. Johansson
invented the gage block in 1896 – and with the help of
Henry Ford it became the world standard as a mea-
surement reference. Johansson’s CEJ Company also
of Eskilstuna was the forerunner maker of these mics.
This set was still in use (see the calibration stickers) in
1981. Given the Ford connection, and significant pen-
etration of Swedish precision instruments into Detroit
(through Ford), it’s likely these were used by an auto
supplier of the time.

$85 donation

Swiss Precision Industries

– SPI – is a distributor
185
Syracuse Twist Drill Co.
was founded prior to 1885 in Syracuse, NY.

Item #543
Syracuse Twist Drill Co (S.T.D. Co
(Syracuse, NY) 0-6” micrometer. Patented by John
Sweet March 10, 1885 and sometimes known as Sweets
Measuring Machine. Marked 582 along with “S.T.D.
Co.” and the Sweets System patent date. A rare pre-
cision tool, about 125 years old, from a city that was
once a manufacturing center. It is adjusted to size
with gage blocks or micrometer standards. Note (from
a calibration sticker) this looks to still have been used
as recently as 1987 – a testament to its robust design.
This should be restored to like-new condition. Bring
the frame to bare metal, add new black enamel, care-
fully polish the bright bits, and make a stand. It will
then happily reside on any engineer’s desk.

$170 donation

Tavannes Machine Co. S.A.

(Tavannes, Switzerland). Tavannes Watch Co. was founded by master watchmaker Henri-Frédéric San-
doz in 1891. The company grew; in part as the Swiss railroad system made accurate timekeeping neces-
sary. In 1923 the company began to make machine tools for the Swiss watch industry. The Smithsonian
notes literature from the Tavannes Machine Co. from the mid 1950’s. Contemporary watch industry cat-
alogs also list the Tavannes / Bergeon horizontal micrometer (below) for well over £600 (about $1000).
Item #544
Tavannes 0-1” bench micrometer with large sat-
in chrome rapid spindle and with a .0001” ver-
nier.
Sold through the watch supply company Bergeron,
Moore & Wright and others. Like all the Tavannes
micrometers listed here, it has the same micrometer
head as the fancier vertical model. Includes a friction/
speeder and a fast-acting (.050/rev) thread. Wrinkle
black painted body. Tavannes sells at least a dozen dif-
ferent anvil combinations for these micrometers. This
has the standard type. Very good condition, with a bit
of paint loss below the measuring area.

$80 donation

186
Item #545
Tavannes 0-1” bench micrometer with large sat-
in chrome rapid spindle and with a .0001” ver-
nier.
As above, with case and better condition. Note that
the anvils of these bench micrometers are replaceable
in different configurations; this has anvils of a some-
what larger than standard diameter – which is good for
all but the smallest features. The case is marked with
the dealer or owner’s information (Albert S. Roethelli
Co., NY). Inside, there’s a calibration notice from 1992.
Excellent condition.

$100 donation

Item #546
Tavannes/Bulova 0-25mm bench micrometer
with plain steel thimble directly reading in
.01mm.
In a custom case marked Tavannes, with the thimble
end marked Bulova Watch Co. #9023. Likely sold
to Bulova watch repair outlets. Wrinkle black painted
body and what look to be small carbide anvils. Good
condition.

$80 donation

187
Item #547
Tavannes 0-1” vertical design “instrument mak-
ers” micrometer, perhaps dating from the 50’s.
Looks a bit like a microscope in aspect, with a tilting
vertical black wrinkle finish frame and a height adjust-
able “stage” with a rotating dial to hold various pin and
arbor sizes. The large dull chrome thimble is marked
“Swiss Made” and has a friction/speeder. It has a rapid
acting screw (advancing .050 rather than .025 per rev-
olution) and easily reads in widely spaced .001 incre-
ments plus a .0001” vernier. Pretty cool.

$90 donation

TESA
(Switzerland) was founded in 1941 as “Telephone SA.” One of the world’s top providers of micrometers
for many years. The company initials TSA appear on its MINMETAL micrometers prior to renaming
the company TESA in 1945.It developed TESA “IMICRO” bore gages in 1950; with some of them being
sold under brand names such as Shardlow (England). The ingenious TESAMASTER digital mechanical
micrometer (with a sort of rotating cube mechanism) was introduced in 1957; and distributed by Brown
& Sharpe in the US. The company essentially merged into B&S in 1967. Around 1993, recession hit
many precision measuring companies and TESA acquired Mercer Ltd., ROCH France (and its subsid-
iary Mauser), and Compac Geneve.
Brown & Sharpe (and TESA with it) was then taken over by the Hexagon AB (a large metrology conglom-
erate) in 2001. Cary (exquisite bench micrometers for the watchmaking industry – of which I have two
examples) was also folded into the mix around this time.
Item #548
TESA (then, TSA) MINMETAL metric microm-
eter 0-25mm ;
probably manufactured between the company’s found-
ing in 1941 and its name change to TESA in 1945.
Very well made WWII era mic in excellent condition.

$50 donation

188
Item #549
Tesa 0-1” Micromaster micrometer in fitted
leatherette case with ratchet and lock.
This is an early model of their mechanical digital mi-
crometers in mint condition. The design (e.g. the
printed decimal equivalents plates) looks to be shortly
after the TSA > TESA name change. Beautiful and un-
common Swiss tool.

$70 donation

Item #550
TESA 0-1” Tesamaster Swiss-made micrometer
with combination direct mechanical readout
and .0001” vernier.
Brown & Sharpe sold this as their #200 model as the
companies first cooperated and later merged. Out-
standing micrometer in excellent condition.

$100 donation

Item #551
TESA 0-1” ISOMASTER Swiss-made microm-
eter with satin chrome and thermal pads.
Speeder, friction thimble, lock, slant lines, and Euro-
style vernier (5 steps, since the mic reads directly to
.0005 in. Slight flaw on front side of frame, otherwise
near perfect in original case.

$60 donation

Item #552
TESA: imitation-is-flattery (?) two pack, con-
sisting of a vintage TESA Swiss-made microm-
eter and its more recent Chinese clone.
The carefully made TESA has a friction “ratchet,” lock,
thermal pads, carbide anvils, and a Euro-style five step
vernier. The Chinese near-clone imitates most ele-
ments, but has a ten step vernier.

$50 donation (two mics)

189
Toyo Seiki Co. Ltd.
(Japan) appears to be a wide ranging manufacturer of components and materials.

Item #553
Toyo Seiki 0-1” micrometer with long ratchet /
speeder, carbide anvils, and a lock.
The age (almost surely after WWII) is not clear to me.
The Toyo logo is of an older style but the chrome thim-
ble looks fairly recent. The locking mechanism also
looks a bit older. In general, lever lock designs have
gone from being machined (like this lock), to stamped
steel (like, say, many Mitutoyo mics), to injection
molded plastic (perhaps a majority of contemporary
mics). In any case, this micrometer works well and has
modest signs of use.

$30 donation

Triumph
Item #554
Triumph 0-25mm micrometer branded for and dis-
tributed by Swartchild – a long-time Chicago supplier
of watchmaking and jeweler’s supplies. Cheaply made.

$5 donation

190
Tubular Micrometer Company (Tumico)
of St. James, Minnesota was manufacturing a line of micrometers with lightweight tubular steel frames by
the “early1940’s” according to the current S-T Industries web site. Their catalog numbering system (e.g.
Tumico catalog 22 in January 1953) would suggest an earlier company start date since most competing
toolmakers printed catalogs no more often than annually. Company catalogs describe their micrometer
frames as hermetically sealed and containing a vacuum. The advantage, especially in larger sizes, was up
to a 50% reduction in weight. While brands like Brown & Sharpe and Starrett commanded most of the
US market during the Tumico years, the quality of their micrometers is generally quite good. Tumico
also made micrometers for others to distribute; most notably the sapphire tipped models for the Elgin
National Watch Co. See also the Scherr-Tumico company entry.
Item #555
Tubular Micrometer Co.
0-13mm mic with plain steel finish. Nice condition
small micrometer for a metric age.

$20 donation.

Item #556
Tubular Micrometer Co.
0-13mm mic with satin chrome plated finish; in origi-
nal cardboard boxed marked model H-50M. Essen-
tially identical to the above micrometer, but with a
more rust resistant finish.

$30 donation

Item #557

Tubular Micrometer Co. 0-1” micrometer with

ratchet, sealed in plastic bag with blue card-
board box and paperwork.
Directly of the Reed design, with a slightly updated
speeder/ratchet. Excellent condition but will likely
need a solvent flush and re-oiling.

$30 donation

191
Item #558
Tubular Micrometer Co. 0-1” mic with chromed
hollow frame, ratchet, lock, and a wood case.
Signs of wear to the hollow chrome frame; otherwise
in good shape.

$30 donation.

Item #559
Tubular Micrometer 0-1” micrometer with a ball
anvil, hollow frame, chrome plated, in a fitted
black case.

$30 donation

Item #560
Tubular Micrometer Co. “rolling mill microm-
eter” with 1” range, a 3” depth throat, and a ra-
dius ground anvil.
Black frame, satin chrome thimble, with a ratchet. The
deep throat allows measurements away from the edge
of a sheet or part. The radius anvil allows the mea-
surement of tubes and pipes in addition to flat articles.
This micrometer was probably made in the 50’s and
remains in good condition with a small brass plate
marked “VEREZ” added (and most likely removable if
desired).

$30 donation

Item #561
Tubular Micrometer Co. (Tumico) 0-4” inter-
changeable anvil micrometer (#M04) with a hol-
low (vacuum sealed) chrome plated frame.
Excellent addition for someone who may occasion-
ally need a larger mic than 0-1” – and complete with
standards and a black padded case. While in excellent
condition, this is the older of the two examples, with a
plain steel thimble.

$50 donation

192
Item #562
Tubular Micrometer Co. (Tumico) 0-4” inter-
changeable anvil micrometer (#M04) with a hol-
low (vacuum sealed) chrome plated frame.
Excellent addition for someone who may occasionally
need a larger mic than 0-1” – and complete with stan-
dards and a wood case. This is the newer of the two
examples, with a satin chrome thimble.

$55 donation

Item #563
Tumico 2-3” crankshaft micrometer with
chromed finish in wood case.
Meant for measuring main bearing journals without
removing the crankshaft from the engine block. Win
“what is it?” bets in bars.

$50 donation

Item #564
Tumico 2-3” crankshaft micrometer with black
wrinkle finish in wood case.
Meant for measuring main bearing journals without
removing the crankshaft from the engine block. Well
made.

$50 donation

Item #565
Tumico 200-300mm interchangeable anvil mi-
crometer in original fitted wood box.
This is complete and in excellent condition with all
four anvils and standards. The micrometer head is
satin chromed with a ratchet and lock. The frame is
brightly chromed and of the tubular form – prized in
larger micrometers like this. Cool. Useful for those
making larger parts to metric dimensions.

$95 donation
See Elgin for a rare sapphire-tipped micrometer made by the Tubular Micrometer Co.

193
Turner
is a century-old leather processing equipment company located in France but with international opera-
tions.

Item #566
Turner leather thickness gage.
I believe this is designed for measuring leather thick-
ness; where 1/16” represents about a 4 ounce leather
weight. Also marked in mm. Looks to be designed
for quick use.

$35 donation

Union Tool Co.

(Orange, Mass). The Union Caliper Co. was established in 1915 and then reorganized as the Union Tool
Co. in 1916. The company had about 100 employees when it was sold, in 1957, to the Millers Fall Co.
I’ve also seen micrometers branded “Union Tool” that were clearly of Millers Falls design (with the ratch-
et at the end of the thimble and a small diameter speeder beyond that).
Item #567
Union Tool Co. 0-1, 1-2, and 2-3” micrometers
made for them by the Central Tool Co.
Includes friction thimbles and lever locks. The 0-1”
has a chrome frame, .0001” vernier, and carbide anvils.
The 1-2” and 2-3” have wrinkle black frames. New-
old-stock condition in original red cardboard cases.
Probably Central /Union’s best model. micrometers.
A collectible bit of precision history (likely 60+ years
old?) and also quite usable.

$90 donation

Item #568
Union Tool Co. 0-1” micrometer #8210 made for
them by Millers Falls.
Includes the nicely designed combination of a speeder
plus ratchet near the thimble end; plus a lock and deci-
mal equivalents. It isn’t clear if this tool preceded the
Millers Falls acquisition or was an attempt to leverage
Union Tool distribution (weak as it was). Example “A.”

$20 donation

194
Item #569
Union Tool Co. 0-1” micrometer #8210 made for
them by Millers Falls.
Includes the nicely designed combination of a speeder
plus ratchet near the thimble end; plus a lock and deci-
mal equivalents. It isn’t clear if this tool preceded the
Millers Falls acquisition or was an attempt to leverage
Union Tool distribution (weak as it was). Example “B.”

$25 donation

Unknown makers
These include a variety of possibly rare, but short-lived, makers with undecipherable names and others
who failed to engrave their micrometers with a brand.

Item #570
Unknown maker 0-1” – almost surely by Starrett
-- and possibly an early prototype.
This micrometer is a puzzle. The thimble and front
lock looks very much like the earliest Starrett microm-
eters (late 1890’s), such as the “Speeded Micrometer”
shown on page 87 of Ken Cope’s “Maker’s of Ameri-
can Machinist’s Tools.” But the frame is of a differ-
ent ribbed style (carefully made and fitted to the old
micrometer head). This frame looks very much like a
Starrett #650 micrometer (e.g. Catalogs #21 and #22),
but those micrometers show a thimble design 20 years
more recent, with both the thimble and frame (as seen
in the catalogs) marked Starrett.
The entire micrometer has no company or patent
markings of any sort; just the graduations. It came in
an owner-built fitted wood box with what also looks
like an owner-made adjustment spanner.

$100 donation

195
Item #571
Unknown manufacturer.
Warning/ “ass whoopin’” sticker designed to protect
your micrometers!

FREE to anyone who donates over $500

Item #572
Unknown 0-25mm micrometer; likely very old
given the style of micrometer and case.
Of standard design; borrowing an early 1900’s design,
judging by late 1800’s Starrett equivalents from which
it may have copied. Marked with what is likely a model
number (1933r, with the r likely for ratchet) and a No.
21898. It looks to be marked with a K and a reversed
N; which might be KU in the Cyrillic alphabet. Nicely
made; showing how the same basic design was dupli-
cated by many manufacturers.
Note: later micrometer boxes from Kalibr in the Soviet
Union were embossed with this logo. It is almost cer-
tainly an early Russian micrometer.

$45 donation.

Item #573
Unknown maker, 0-25mm micrometer
with knurled friction thimble and made to resemble
a very early style. This is likely a more recent (say,
1950’s) and modestly priced import. The thread wear
adjustment screw is not original.

$5 donation

196
Item #574
Unknown maker, early 0-15mm+ micrometer,
most likely for the watchmaking trade (note the small
anvils). The carefully inscribed indications, fancy
and large friction knurled thimble, open threads, and
(worn) chrome-plated brass construction suggest a
somewhat older micrometer.

$25 donation

Item #575
Unknown maker tiny circular form metric mi-
crometer with a thickness gage (tenths of a mm)
around the periphery of the brass disk.
The whole thing is about 3 cm. in diameter. Meant for
watch/clock/jeweler’s trades.

$30 donation

Item #576
Unknown Swiss 0-10mm open thread microme-
ter with brass frame. Despite the Swiss origin (marked
Suisse and Switzerland on the frame) this is a modest
quality mic made to be sold into the watchmaking and
jewelry industry. Almost surely post WWII. Looks
quite usable.

$15 donation

Item #577
Unknown maker 0-1” key micrometer in black
leather case.
While somewhat similar in appearance to a wire mi-
crometer this is meant for measuring keys; to identify
which pins go into the mating lock cylinder. The blade
anvil fits the indentations of the key. With satin chrome
micrometer head, friction thimble, and purpose-built
frame and anvil. Well made, in excellent condition.

$30 donation

197
Item #578
Unknown maker 0-1” micrometer with chrome
plate over a non-ferrous die cast frame.
The die casting has raised decimal equivalents, a fake
lock is cast in, and the frame is marked “No. 86” and
“G.L.” Chrome plated steel thimble with a speeder.
Low cost mic.

$15 donation

Item #579
Unknown manufacturer. Group of four promo-
tional micrometers; Case Iron & Metal; Sheldon
Printing Machines, Penn Electric/Stanley Tools;
and Garsite Products.
There is also a U.S. Steel version, sold separately. These
were for valued customers; and have sold at auction for
as much as $30+ each. Chrome and gold tone ver-
sions. Why buy four? Establish a secret micrometer
conspiracy with four neighbor kids (grandkids, nieces,
nephews . . .) each with their own micrometer!

$45 donation

Item #580
Unknown maker “United States Steel” 0-.5” mi-
crometer.
Promotional micrometer (unknown manufacturer)
given to the best customers at a time when U.S. Steel
was still the globe’s dominant supplier. Pretend you
were once a big time steel customer. This is by the same
maker of the group of four promotional mics above.

$20 donation

Item #581
Unknown maker (West Germany) 0-25mm mi-
crometer distributed by HR.
Note also a French-made (E.D.A.) micrometer in this
collection distributed by HR to the watchmaking and
jewelry trades. Good quality with an open thread and
a nicely made friction/speeder.

$25 donation

198
Item #582
Unknown maker, cast copy of a Starrett #230 mi-
crometer.
Like the broken clock, it’s dead accurate every once in
a while? Someone went to a great deal of trouble to
make this; but note the casting shrinkage in the frame
area.

$25 donation

Item #583
Unknown 1-2” micrometer marked “Made in
Germany.”
Includes a long ratchet / speeder, a lock, and decimal
equivalents on the frame. A design match (likely the
same German factory) as the “Zeus” micrometer noted
elsewhere -- and it would make sense to acquire both.

$25 donation

Item #584
Unknown 0-1” micrometer with long speeder /
ratchet and marked “Made in Germany.”
This is a useful design feature, as it allows use of the
speeder without engaging the ratchet. This appears
to the same maker as the “Supreme” branded microm-
eter described elsewhere; with the addition of a bright
chrome frame and stamped decimal equivalents. Also,
marked “Made in West Germany” on the bottom of the
black case; dating it from the end of WWII until reuni-
fication around 1990. Well made micrometer in mint
condition.

$35 donation

199
Item #585
Unknown Japanese maker 0-25mm micrometer
with fancy knurling and unusual anvil adjust-
ment design.
Necked anvils, for small parts. Nicely executed. An im-
perfect translation of the Kanji suggests this is a model
no. 142 made at the Tokyo precision equipment manu-
facturing division. I don’t have enough information
to date this as pre-WWII (it’s an older style) or later.

$45 donation

Item #586
Unknown (Japanese) maker 0-25mm microm-
eter with fancy knurling and unusual anvil ad-
justment design.
Same design and manufacture as the liberally marked
example above, but completely bare of any markings
(and likely for export?).

$40 donation

Item #587
Unknown maker -- Shanghai micrometer box.
From earlier export days, when Chinese goods had
pride of place?

$5 donation

Item #588
Unknown manufacturer 1-2” micrometer
marked “ITI New York” within a triangular logo
and made in Japan.
The mic looks close in design to either NSK or Mitu-
toyo; but isn’t an exact match for any I’ve seen. It’s
remotely possible that ITI refers to the old home study
institute, a distributor, or ?? In any case, a well made
mic with a ratchet, lock, carbide faces, decimal equiva-
lents on the pads, and a .0001 vernier. Includes its
painted (black) wood box.

$35 donation

200
Item #589
Unknown large 6-12” interchangeable anvil mi-
crometer set in large purpose-built wood case.
The micrometer heads are Starrett-made with a style
from around the 1940 time period. The two unmarked
heavy frames (6-9” and 9-12”) look to be one-off cast-
ings. One possible explanation is that this set was cre-
ated by an enterprising machinist / foundry man dur-
ing WWII. At that time, it was extremely difficult to
acquire less common precision measuring tools unless
one had a high defense priority – and even then there
were often long waits. In any case, this is truly a bit of
Yankee ingenuity, well executed, and still accurate for
use.

$140 donation

Item #590
Unknown
– Mitutoyo-style outside micrometer stand still in
original cardboard box. An Asian import, but of fully
acceptable quality for its intended purpose. Show off
your generosity and precision acumen (or acuwoman
as the case may be). #1

$15 donation

Item #591
Unknown
– Mitutoyo-style outside micrometer stand still in
original cardboard box. An Asian import, but of fully
acceptable quality for its intended purpose. Show off
your generosity and precision acumen (or acuwoman
as the case may be). #2

$15 donation

201
Item #592
Unknown
Outside micrometer stand still in original cardboard
box. Needs a rubber pad at the back, otherwise good.
Eases use by leaving a hand free. Improves precision by
reducing the effect of hand warming on the micrometer
frame. Also, turns anything cool into desk art. Comes
in industry’s always-favorite black and blue.

$15 donation

Item #593
Union lapel pin (Qualified Millwright & Ma-
chine Erector)
featuring a micrometer as its iconic symbol.

$25 donation

Item #594
Unknown maker -- male die for micrometer
pins; deep paper embossing, or ???
$20 donation

Item #595
Unknown Chinese maker 0-1” mechanical digi-
tal micrometer.
Compare to Brown & Sharpe, Central Tools Co, Mitu-
toyo, NSK, Slocomb, Starrett and others.

$15 donation

202
Item #596
Unknown Chinese-maker 3-4” micrometer of a
type now widely and inexpensively available.
Satin chrome, ratchet, lever lock, and a vernier that al-
most inspires visions of .0001” accuracy. An Etalon
micrometer spindle is included to note the rough simi-
larity in design.

$20 donation

Item #597
Unknown German maker 0-1” micrometer with
ratchet, center lock, and decimal equivalents –
pretty much the worldwide standard design.
Compare to similar makes from the US, Japan, Swe-
den, etc. In nice wooden box with a dovetail fit sliding
cover with one end rounded.

$20 donation

The Van Keuren Co.

was founded March, 1920 to manufacture “Light Wave Measuring Equipments.” It invented the extreme-
ly accurate and unique light wave micrometer and also went on to become a premier supplier of optical
flats and gauging equipment. The company is now operated as a division of PMC Lodestar. For years,
VK produced a hardbound catalog and handbook, itself valued for the information provided on optical
flats, reading fringes, precision gages, and light wave microscopy.
Item #598
Van Keuren 0-2” Light Wave Micrometer in case.
While average micrometers are accurate to .001 and
better micrometers to .0001, this is accurate to .00001
(10 millionths of an inch). It includes an adjustable
and extremely repeatable system for maintaining the
same pressure in readings; along with a “near perfect”
micrometer screw. Included is the valuable Handbook
No. 36. which has a chapter covering use and a price
list. This micrometer would cost nearly $5000 in to-
day’s inflated dollars.

$300 donation

203
VIS/SPI/etc.
These micrometers were among the first to combine satisfactory quality with a lower price. They also
signaled a Poland that was leveraging the talents of its people and becoming more open to the world. The
basic design/build was sold under several names (e.g. VIS) and by several distributors (e.g. SPI – Swiss
Precision Industries – which apparently didn’t bother to rename itself Polish Precision Industries).
Item #599
0-1” and 1-2” micrometers made in Poland.
The mics bear a strong resemblance to Mitutoyo mi-
crometers with a friction thimble, green enamel frame,
a similar lock, etc. These were popular a decade or
two ago; but Chinese variants now own the low cost
niche. See also the “Mitutoyo > Poland two pack” for
a Mitutoyo mic and a Polish mic for comparison.

$35 donation

Warszawa
(Poland)

Item #600
Warszawa (a.k.a. Warsaw) 0-1” micrometer with
heavy satin chrome frame, thermal pads, ratch-
et, and lock in fitted wood case.
This was likely made after WWII, along the lines of
Russian micrometers of the time, and meant for export.
An early step towards Poland becoming one of Europe’s
leading manufacturers today. Marked N-10004 on the
back thermal pad. Well made and excellent condition.

$45 donation

Item #601
Warszawa logo
0-25mm indicating micrometer with black wrinkle
frame. The comparator reads to .002mm and it includes
all the usual indicating micrometer features such as an
anvil release and lock. These mics have a reputation of
offering good quality at a somewhat lower price. Ex-
cellent condition in original wood box.

$75 donation

Welch
--see Central Tool Company

204
Wells Brothers Company
(Greenfield, Mass) was founded in 1876 by Frederick E. and Frank O. Wells. In 1879 the came became
known as Wells Brothers & Co and in 1888 Wells Brothers Co. Their specialty was the manufacture of
taps and dies, under the famed “Little Giant” trademark. In 1912, Wells Brothers was acquired by Green-
field Tap & Die (itself founded in 1912).
Item #602
Wells Bros. Company 0-1” unusual point/thread
micrometer with a patent date of July 28, 1903
(corresponds to #734,784) stamped on the rear
of the frame.
This has a clever side-adjustable anvil to accommodate
different pitches. Tarnished all over (it might electro-
polish) but in good working condition. Probably de-
signed as a complement to the tap and die business.
This is rare enough to have escaped mention in both
of Ken Cope’s definitive works – Makers of American
Machinist’s Tools and More Makers of American Ma-
chinist’s Tools.

$120 donation

A.J. Wilkinson & Co.

(Boston, Massachussetts)
Item #603
0-1” micrometer
with 1883 patent dates. Rare and valuable microm-
eter in very good condition, with an original case that
needs repair. The donation price is less than I paid for
it and less than it should bring at auction.

$300 donation

205
WJZ Gage & Tool Corp.
(Hyde Park, NY) was founded in 1951.

Item #604
WJZ 1-2” pistol grip snap gage with a good ($$$)
Federal .0001” reading indicator.
Adjustable within its range for both size and depth. It
looks to have carbide pads inset into the anvils. Fitted
wood box with an “inactive” standard enclosed. Needs
a cleaning and the paint will still be spotty – but looks
to be in good measuring condition. Cool enough to
grab pistol style and say “don’t make me use this.”

$60 donation

Woodman Mfg. and Supply Co.

rpm indicator Sept. 12, 1876 patent.
Item #605
Kind of a Victorian look to it. The idea is to count the
revolutions ( say, a steam engine driven line shaft) over
a measured time to get rpm’s. No idea what it’s worth,
beyond the $70 one dealer wants for his. Starrett and
others still sell a modern version. If your head is spin-
ning, now at least you’ll know how fast.

$25 donation

Carl Zeiss Jena

(Jena, Germany) – best known as a precision optical firm, founded in 1846. The company has a long his-
tory in optical metrology and coordinate measuring machines, while micrometers appear to have been
a brief fling. The firm was partitioned after WWII with “Carl Zeiss” in West Germany and “VEB Carl
Zeiss Jena” in East Germany.
Item #606
Carl Zeiss Jena 0-.75” disk micrometer with
built-in comparator and push button anvil re-
lease.
The extra large disk anvils allow measuring soft materi-
als and reaching difficult features (such as gear teeth).
The built in comparator as well as the vernier read
directly to .0001” -- a cool and useful micrometer in
good condition.

$90 donation

206
Item #607
Carl Zeiss Jena 0-10mm bench micrometer with
large steel thimble reading in .01mm.
Includes a ratchet and the Zeiss nameplate affixed
within the deep “U” throat of the micrometer. Very
good condition – would clean up to be worthy of either
measuring duties and/or a spot in your office.

$65 donation

Item #608
Carl Zeiss Jena 0-25mm micrometer.
Standard design but carefully made of high quality tool
steel. And note the tiny engraved admonition to mea-
sure at 20 degrees C. My guess is that this tool predates
WWII.

$35 donation
Item #609
Carl Zeiss Jena 25-50mm indicating micrometer
in original black wooden case.
This is in good operating condition, but needs calibra-
tion and the window cover replaced if it is to be put
into service. Includes the calibration spanners and
standard.

$50 donation

Item #610
Carl Zeiss Jena 8-10” indicating micrometer
with unusual comparator on the anvil end,
carbide anvils, a ratchet, lock, and .0001” vernier. In-
cludes large wood case and a setting standard. This
is cool enough to mount on a display stand and large
enough to dispel any slurs about manhood. Probably
a $1000 mic when Zeiss was still in this business. An
esoteric question with this tool is the 62o marking on
the frame. Assuming this is calibration temperature it
is several degrees cooler than normal.

$140 donation

207
Zeus
(Germany)—likely an export brand rather than a maker.

Item #611
Zeus 0-1” micrometer with long ratchet / speed-
er, a lock, decimal equivalents on the frame, and
a black fitted case.
Typical German design for export. This would be
a same-design pair with an unknown 1-2” “Made in
Germany” micrometer noted elsewhere.

$30 donation

Zim Manufacturing Co.

(Chicago, IL) makes automotive tools.
Item #612
Zim #165 cylinder gauge for small engines,
range 1 ¾” to 3 ¼” bore.
Missing a couple extension arms (one is attached),
which look easy to make to any bore size you want as
long as it’s 1 ¾” or larger. Pretty crude, but likely ser-
viceable to rebuild your Briggs & Stratton. It’s preset to
zero, and measures to .001 in.

$20 donation

Miscellaneous items
Item #613
Explora-micrometer-em kit of about 25 microm-
eters.
These have previous owner’s marks or broken parts or
signs of beating and abuse. But many are salvageable
and a few date back to the late 1890’s or early 1900’s. A
few are OK as is. Also lots of assorted parts.
Maybe some group of kids will have fun seeing how
many micrometers they can fix up out of the lot? With
the rest as C-clamps?? Also some new parts for Mi-
tutoyo, Starrett, etc. There’s at least one micrometer
worth the near the $25 alone (e.g. the larger Millers
Falls).

$25 donation

208
Item #614
Adjustment wrenches.
If yours is missing (many are) find the correct type (a
modest challenge – basically match up the diameter of
the hub and pin spanner) and find one that matches.
There are usually at least two adjustments. One to
rotate the barrel graduations. Another to tighten the
spindle adjustment screw. There should be enough of
these to go around at one per attendee . . .

Free with a micrometer donation

209
210