6411-6414
LOW TOX®
TURBINE OIL
Designed for use where environmental concerns dictate
the use of very low toxicity turbine oil.
Lubrication Engineers’ LOW TOX Turbine Oils offer superior performance in lubrication, with
long oil life and excellent wear protection. There is no worry of premature oxidation or failure of
the lubricant as there is with most vegetable oil based products. LOW TOX Turbine oils are
based on USP quality white mineral oils and specially selected additives to provide a low toxicity
product with good biodegradability that does not sacrifice lubrication performance or necessitate
shortening of lubricant change intervals.
;lk;lk
USER BENEFITS:
• Reduced ecotoxity – Lowest toxic effect • Excellent demulsibility and seal compatibility.
on aquatic organisms, Up to a tenfold • Resists hydrolysis better than vegetable or
reduction in ecotoxicity without any synthetic ester based oils.
compromise in lubricant or turbine • Versatility – Available in a number of
performance. viscosity grades. LOW TOX Turbine Oils
• Longer life – lasts significantly longer meet the different requirements of various
than vegetable based oils. types of equipment.
• Oxidation stability – Two to three times
better oxidation stability than conventional 6411 ISO 32
oils. 6412 ISO 46
• Performance – LOW TOX Turbine oils 6413 ISO 68 SAE 20
are superior to conventional oils while 6414 ISO 100 SAE 30
offering significantly reduced toxicity.
TYPICAL APPLICATIONS: WHY LOW TOXICITY?
• Hydro-turbines One question confronting scientists in
• Generators environmental risk assessment is whether it
• Governors is better for a material to be quickly
• Downhole Water Pumps biodegraded and possess relatively high
• Forestry/Logging Equipment toxicity or be low in toxicity and biodegrade
• Water/Wastewater Treatment Plants at a slightly slower rate. Lubrication
• Paper Mills Engineers believes than the latter option
• Other applications where low toxicity and provides the best protection of the
minimal environmental impact is desirable. environment because it minimizes overall
impact on the ecosystem.
LE products manufactured under an ISO
9001:2000 Certified Quality System
LEADERS IN LUBRICANTS
300 Bailey Ave • FORT WORTH, TEXAS • 817-834-6321 • FAX 817-834-2431 • http://www.le-inc.com
LE’s LOW TOX® Oils
Show High EC50 Value in
®
Microtox Luminescent Bacteria Bioassay Test.
EC 50: Effective concentration measured in milligram of product per liter of water. Tells you the
effective concentration of the product being measured and what quantity it takes to reduce
bacterial luminescence metabolic activity by 50%. EC Values are applicable to compounds
which are not soluble in water, therefore, they are applicable to oils.
Lubrication Engineers’ LOW TOX Hydraulic and Turbine Oils are less toxic to the environment
than conventional and biodegradable products available today. The issue of biodegradability is
not the only concern. A further concern is the toxic effect on the environment of a lubricant
during the time that biodegradation is taking place. Lubrication Engineers’ Low Tox product line
is 55% biodegradable in 28 days and has the lowest toxicity of any hydraulic or turbine products
on the market today, as shown by the Microtox Luminescent Bacteria Bioassay Test.
LI30007
Rev. 01-98
LEADERS IN LUBRICANTS 6411-6414 Flyer
300 Bailey Ave • FORT WORTH, TEXAS • 817-834-6321 • FAX 817-834-2431 • http://www.le-inc.com
LUBRICATION ENGINEERS®, INC.
P.O. Box 7128 FORT WORTH, TX 76111-0128
MATERIAL SAFETY DATA SHEET
*************************SECTION I*************************
PRODUCT IDENTIFICATION
SUPPLIER: EMERGENCY TELEPHONE NUMBERS.:
®
Lubrication Engineers , Inc. Company: (817) 834-6321
P.O. Box 7128 In the event of an emergency spill, fire, or exposure—Call:
Fort Worth, TX 76111-0128 Chemtrec: (Within USA) (800) 424-9300
(Outside USA—call collect) (703) 527-3887
CHEMICAL NAME AND SYNONYMS: TRADE NAME AND SYNONYMS:
Not applicable 6412 Low Tox Turbine Oil
CHEMICAL FAMILY: FORMULA:
Hydrocarbon Not applicable
*************************SECTION II*************************
TYPICAL CHEMICAL AND PHYSICAL PROPERTIES
APPEARANCE: VISCOSITY: @ 210°F, SUS @ 100°C, cSt
Straw color lubricant 48.14 6.63
ODOR: VISCOSITY: @ 100°F, SUS @ 40°C, cSt
Lube oil odor 239.5 46.50
RELATIVE DENSITY: SOLUBILITY IN WATER: PH: 6-8
(Air=1) >1 Negligible
MELTING POINT: °F POUR POINT: °F
Not applicable 0
BOILING POINT: °F FLASH POINT: °F (Method)
>500 455 (C.O.C.)
VAPOR PRESSURE: SPECIFIC GRAVITY: (H2O=1)
(mm Hg @ 60°F) <5 0.87
*************************SECTION III*************************
INGREDIENTS
WT PCT TLV ORAL DERMAL
(APPROX) LD50 LD50
HAZARDOUS INGREDIENTS:
3
Oil Mist (mineral) >95.0 5 mg/m -TWA Unknown Unknown
NON-HAZARDOUS INGREDIENTS:
ADDITIVES AND/OR OTHER INGREDIENTS: This product is a mixture. The specific chemical identity of hazardous ingredients and
non-hazardous ingredients, their C.A.S. numbers and their exact percent of composition are proprietary to Lubrication Engineers®, Inc. and
are being withheld as Trade Secrets. The above listing of hazardous ingredients discloses the properties, approximate concentration and
known toxicological effects of the hazardous ingredients. This material is an automotive/industrial lubricant with a low order of toxicity and
irritancy. The product is formulated with ingredients that are not designated as harmful to the ozone.
REGULATORY INFORMATION:
SARA Title III: This product does not contain any chemical substance on the SARA Extremely Hazardous Substances list. If this product
contains any chemicals that are subject to the reporting requirements of Section 313 of Title III of the Superfund Amendments and
Reauthorization Act of 1986 and 40 CFR Part 372, they will be listed in the above HAZARDOUS INGREDIENTS section.
TSCA: This material is in compliance with the Toxic Substances Control Act (15 USC 2601-2629) and all components of this product appear
on the Toxic Substance Control Act (TSCA) inventory list.
6412 Low Tox Turbine Oil
Effective Date: January 20, 2005 Print Date: January 27, 2005 Page 1
Clean Air Act: No ozone depleting chemicals listed in Title VI, Stratospheric Ozone Protection, Section 602 of the Clean Air Act are present or
used in the manufacturing process of this product.
*************************SECTION IV*************************
FIRE AND EXPLOSION HAZARD DATA
FLASH POINT: °F (Method) FLAMMABLE LIMITS: LEL UEL
455 °F (C.O.C.) Unknown
EXTINGUISHING MEDIA:
Foam, dry chemical, water fog, or carbon dioxide
SPECIAL FIRE FIGHTING PROCEDURES:
Do not direct a solid stream of water into fire. Treat as a petroleum oil fire. Respiratory protection required for fire fighting personnel.
UNUSUAL FIRE AND EXPLOSION HAZARDS:
None
*************************SECTION V*************************
HEALTH HAZARD DATA
THRESHOLD LIMIT VALUE: (If Established)
3
Not established. Oil mist = 5mg/m
EFFECTS OF OVEREXPOSURE:
Although there are no consistent primary routes of entry, the product may cause mild dermatitis upon prolonged contact and is expected to be
an eye and lung irritant. Any existing skin, eye, or lung irritation may be aggravated by direct contact. No components are listed on OSHA,
I.A.R.C., or N.T.P. lists for carcinogens.
*************************SECTION VI**************************
EMERGENCY AND FIRST AID PROCEDURES
EYE CONTACT:
Flush immediately with water until irritation subsides.
SKIN CONTACT:
Wash affected skin area with mild soap and water.
INGESTION:
Do not induce vomiting. Contact a physician.
INHALATION:
Remove to fresh air. If not breathing, give artificial respiration. Contact a physician.
*************************SECTION VII***************************
REACTIVITY DATA
STABILITY: (Thermal, Light, Etc.) CONDITIONS TO AVOID:
Stable Contact with nuclear radiation and strong oxidizing materials.
INCOMPATIBILITY: (Materials to avoid)
Strong oxidizing materials.
HAZARDOUS DECOMPOSITION PRODUCTS:
Dense smoke; oxides of C, S, N and P; hydrogen sulfide.
HAZARDOUS POLYMERIZATION:
Will not occur.
*************************SECTION VIII**************************
SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED:
Remove all sources of ignition. Treat as a petroleum oil spill.
6412 Low Tox Turbine Oil
Effective Date: January 20, 2005 Print Date: January 27, 2005 Page 2
WASTE DISPOSAL METHOD:
Incinerate where permitted under federal, state, and local laws. Used petroleum products may be recycled through re-refining processes.
*************************SECTION IX**************************
SPECIAL PROTECTION INFORMATION
EYE PROTECTION:
Sufficient to avoid direct contact.
SKIN PROTECTION:
Protective neoprene or plastic gloves may be desired.
RESPIRATORY PROTECTION:
Usually not needed in open, unconfined areas.
VENTILATION:
Usually not needed in open, unconfined areas.
OTHER:
Usually not needed.
*************************SECTION X*************************
SPECIAL PRECAUTIONS
Close containers when not in use. Keep away from heat, sparks, open flames, and strong oxidants. Avoid eye contact and prolonged skin contact.
Avoid breathing oil mists. Wash thoroughly after handling.
*************************SECTION XI**************************
HAZARD RATINGS
There are several recognized and accepted systems that assign hazard ratings to materials. Although this product has not been evaluated specifically
against these systems, the ratings for the National Fire Protection Association (NFPA) and the National Paint and Coatings Association's Hazardous
Material Identification System (HMIS) are:
NFPA HMIS
Health 2 1
Flammability 1 1
Reactivity 1 1
6412 Low Tox Turbine Oil
Effective Date: January 20, 2005 Print Date: January 27, 2005 Page 3
LUBRICATION ENGINEERS®, INC.
P.O. Box 7128 FORT WORTH, TX 76111-0128
MATERIAL SAFETY DATA SHEET
*************************SECTION I*************************
PRODUCT IDENTIFICATION
SUPPLIER: EMERGENCY TELEPHONE NUMBERS.:
®
Lubrication Engineers , Inc. Company: (817) 834-6321
P.O. Box 7128 In the event of an emergency spill, fire, or exposure—Call:
Fort Worth, TX 76111-0128 Chemtrec: (Within USA) (800) 424-9300
(Outside USA—call collect) (703) 527-3887
CHEMICAL NAME AND SYNONYMS: TRADE NAME AND SYNONYMS:
Not applicable 6413 Low Tox Turbine Oil
CHEMICAL FAMILY: FORMULA:
Hydrocarbon Not applicable
*************************SECTION II*************************
TYPICAL CHEMICAL AND PHYSICAL PROPERTIES
APPEARANCE: VISCOSITY: @ 210°F, SUS @ 100°C, cSt
Light straw lubricant 53.48 8.21
ODOR: VISCOSITY: @ 100°F, SUS @ 40°C, cSt
Lube oil odor 331.1 64.05
RELATIVE DENSITY: SOLUBILITY IN WATER: PH: 6-8
(Air=1) >1 Negligible
MELTING POINT: POUR POINT: °F
Not applicable +5
BOILING POINT: °F FLASH POINT: °F (Method)
>500 460 (C.O.C.)
VAPOR PRESSURE: SPECIFIC GRAVITY: (H2O=1)
(mm Hg @ 60°F) <5 0.87
*************************SECTION III*************************
INGREDIENTS
WT PCT TLV ORAL DERMAL
(APPROX) LD50 LD50
HAZARDOUS INGREDIENTS:
3
Oil Mist (mineral) >95.0 5 mg/m -TWA Unknown Unknown
NON-HAZARDOUS INGREDIENTS:
ADDITIVES AND/OR OTHER INGREDIENTS. This product is a mixture. The specific chemical identity of hazardous ingredients and
non-hazardous ingredients, their C.A.S. numbers and their exact percent of composition are proprietary to Lubrication Engineers®, Inc. and
are being withheld as Trade Secrets. The above listing of hazardous ingredients discloses the properties, approximate concentration and
known toxicological effects of the hazardous ingredients. This material is an automotive/industrial lubricant with a low order of toxicity and
irritancy. The product is formulated with ingredients that are not designated as harmful to the ozone.
REGULATORY INFORMATION:
SARA Title III: This product does not contain any chemical substance on the SARA Extremely Hazardous Substances list. If this product
contains any chemicals that are subject to the reporting requirements of Section 313 of Title III of the Superfund Amendments and
Reauthorization Act of 1986 and 40 CFR Part 372, they will be listed in the above HAZARDOUS INGREDIENTS section.
TSCA: This material is in compliance with the Toxic Substances Control Act (15 USC 2601-2629) and all components of this product appear
on the Toxic Substance Control Act (TSCA) inventory list.
6413 Low Tox Turbine Oil
Effective Date: January 20, 2005 Print Date: January 27, 2005 Page 1
Clean Air Act: No ozone depleting chemicals listed in Title VI, Stratospheric Ozone Protection, Section 602 of the Clean Air Act are present or
used in the manufacturing process of this product.
*************************SECTION IV*************************
FIRE AND EXPLOSION HAZARD DATA
FLASH POINT: °F (Method) FLAMMABLE LIMITS: LEL UEL
460°F (C.O.C.) Unknown
EXTINGUISHING MEDIA:
Foam, dry chemical, water fog, or carbon dioxide
SPECIAL FIRE FIGHTING PROCEDURES:
Do not direct a solid stream of water into fire. Treat as a petroleum oil fire. Respiratory protection required for fire fighting personnel.
UNUSUAL FIRE AND EXPLOSION HAZARDS:
None
*************************SECTION V*************************
HEALTH HAZARD DATA
THRESHOLD LIMIT VALUE: (If Established)
3
Not established. Oil mist = 5mg/m
EFFECTS OF OVEREXPOSURE:
Although there are no consistent primary routes of entry, the product may cause mild dermatitis upon prolonged contact and is expected to be
an eye and lung irritant. Any existing skin, eye, or lung irritation may be aggravated by direct contact. No components are listed on OSHA,
I.A.R.C., or N.T.P. lists for carcinogens.
*************************SECTION VI**************************
EMERGENCY AND FIRST AID PROCEDURES
EYE CONTACT:
Flush immediately with water until irritation subsides.
SKIN CONTACT:
Wash affected skin area with mild soap and water.
INGESTION:
Do not induce vomiting. Contact a physician.
INHALATION:
Remove to fresh air. If not breathing, give artificial respiration. Contact a physician.
*************************SECTION VII***************************
REACTIVITY DATA
STABILITY: (Thermal, Light, Etc.) CONDITIONS TO AVOID:
Stable Contact with nuclear radiation and strong oxidizing materials.
INCOMPATIBILITY: (Materials to avoid)
Strong oxidizing materials.
HAZARDOUS DECOMPOSITION PRODUCTS:
Dense smoke; oxides of C, S, N and P; hydrogen sulfide.
HAZARDOUS POLYMERIZATION:
Will not occur.
*************************SECTION VIII**************************
SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED:
Remove all sources of ignition. Treat as a petroleum oil spill.
WASTE DISPOSAL METHOD:
Incinerate where permitted under federal, state, and local laws. Used petroleum products may be recycled through re-refining processes.
6413 Low Tox Turbine Oil
Effective Date: January 20, 2005 Print Date: January 27, 2005 Page 2
*************************SECTION IX**************************
SPECIAL PROTECTION INFORMATION
EYE PROTECTION:
Sufficient to avoid direct contact.
SKIN PROTECTION:
Protective neoprene or plastic gloves may be desired.
RESPIRATORY PROTECTION:
Usually not needed in open, unconfined areas.
VENTILATION:
Usually not needed in open, unconfined areas.
OTHER:
Usually not needed.
*************************SECTION X*************************
SPECIAL PRECAUTIONS
Close containers when not in use. Keep away from heat, sparks, open flames, and strong oxidants. Avoid eye contact and prolonged skin contact.
Avoid breathing oil mists. Wash thoroughly after handling.
*************************SECTION XI**************************
HAZARD RATINGS
There are several recognized and accepted systems that assign hazard ratings to materials. Although this product has not been evaluated specifically
against these systems, the ratings for the National Fire Protection Association (NFPA) and the National Paint and Coatings Association's Hazardous
Material Identification System (HMIS) are:
NFPA HMIS
Health 2 1
Flammability 1 1
Reactivity 1 1
6413 Low Tox Turbine Oil
Effective Date: January 20, 2005 Print Date: January 27, 2005 Page 3
