Step 1 Assemble Base Frame
Parts:
2020 Aluminium profile 355mm – 2pcs
2020 Aluminium profile 380mm – 2pcs
2020 Aluminium profile 500mm – 4pcs
Acrylic corner cushion – 4pcs
M4-10mm screw – 8pcs
M4 T-Nut – 8pcs
M5-25mm screws – 4pcs
Step 2 Assemble Top Frame
Parts:
2020 Aluminium profile 355mm – 2pcs
2020 Aluminium profile 380mm – 2pcs
Corner bracket –8pcs
M4-8mm screws –16pcs
M4 T-Nut –16pcs
M5-25mm screws – 4pcs
Step 3 Assemble Z axis
1 2 3
Parts:
1: Y axis motor – 1pcs
Y axis motor holder (acrylic) – 1pcs
Pulley (with grub screw in it) – 1pcs
M3-45mm screws – 4pcs M4-10mm screws –2pcs
M4 T-Nut –2pcs
2: Z endstop – 1pcs Z endstop holder – 1pcs
M2-10mm – 2pcs M3-16mm – 1pcs M3 nut – 1pcs
4
3: Z axis motor – 1pcs Z motor holder(acrylic) – 1pcs
M3-45mm screws – 4pcs M4-10mm screws –2pcs
M4 T-Nut –2pcs coupling – 1pcs
Lead screw 385mm -1pcs
4: Flange bearing – 2pcs Copper nut – 1pcs
M3-45mm screws – 1pcs Spring – 3pcs
Flange bearing holder – 1pcs M3-10mm screws – 8pcs
5
5: KFL08 bearing – 1pcs Sliding rod holder – 2pcs
M4-10mm screws – 6pcs M4 nuts – 6pcs
Sliding rod 460mm – 2pcs
Step 4 Assemble KP08 Bearings
Parts:
KP08 Bearing – 4pcs
M4-8mm screws –8pcs
M4 T-Nut –8pcs
Step 5 Assemble SK8 support shaft
Parts:
SK8 support shaft – 4pcs
M4-8mm screws –8pcs
M4 T-Nut –8pcs
Step 6 Assemble sliding rods
Parts:
Sliding rod 420mm – 2pcs
Pulley (with grub screw in it) – 5pcs
Closed belt – 1pcs
Step 7 Assemble X-pulley&motor mount
Parts:
Sliding rod 395mm -2pcs
LM8UU linear bearing – 8pcs
X-Pulley mount – 1pcs
X-motor mount – 1pcs
Y-endstop – 1pcs
Y-endstop mount – 1pcs
M2-10mm – 2pcs
M3-16mm – 1pcs
M3 nut – 1pcs
Step 8 Assemble X axis
Parts:
①
Belt pulley – 1pcs
M5-32mm screw – 1pcs
① M6 washer – 3pcs
③ M5 washer – 2pcs
M5 nut – 1pcs
②
X endstop – 1pcs
X endstop holder ( acrylic) – 1pcs
M2-10mm screw – 2pcs
M2-10mm nut – 2pcs
M3-40mm nut – 2pcs
② ③
Sliding rod 360mm – 2pcs
Extruder assembly – 1pcs
Step 9 Assemble heat bed
Parts:
Timing belt – 1pcs
Zip-ties – 2pcs
Tighten one end of the timing belt to the belt
hole which is on the extruder using a zip-ties .
Run the other end of timing belt to the X-Motor-
Pulley and Belt pulley . Then tighten it to another
belt hole using a zip-ties, as shown in the picture .
Step 10 Assemble timing belt
Parts:
Timing belt – 2pcs
Belt clip – 4pcs
M3-10mm screws – 8pcs
Tighten one end of the timing belt using belt clip
and M3-10mm screws , the other end through
pulley from left and right side , the tighten it on
the pulley mount , as picture
The same install method for X motor mount
Step 11 Assemble Base Frame
Parts:
Bed holder (aluminium) – 2pcs
Heat bed – 1pcs
M3-35mm – 4pcs
Springs – 4pcs
Wing nut – 4pcs
M4-10mm – 4pcs
Step 12 Assemble Power supply & Mainboard
Parts:
①
Power supply – 1pcs
Power supply holder (acrylic) – 1pcs
M3-10mm screws – 3pcs
M4-12mm screws – 3pcs
M4 T-Nut – 3pcs
②
Mainboard – 1pcs
Mainboard holder (acrylic) – 1pcs
M3-20mm screws – 4pcs
Plastic Pillar – 4pcs
②
M3 nut – 4pcs
① M4-12mm screws – 3pcs
M4 T-Nut – 3pcs
Step 13 Assemble LCD display
Parts:
LCD display – 1pcs
LCD display holder – 1pcs
M3-20mm – 4pcs
M3 nuts – 4pcs
Plastic pillar – 4pcs
Control knob – 1pcs
M4-12mm screws – 3pcs
M4 T-Nut – 3pcs
Step 14 Control Board Wiring Diagram
The method of connecting wire is as picture
!NOTE!: The wires connected to POWER SUPPLY and
HETBED must be AWG14 or thicker one.
X
No Connection
Step 15 AC Power Connector Wiring Diagram
Connect Power cable as the picture (Left)
Note: There are different voltages in different
country. Please select the appropriate voltage by
switch before power on. As the picture below.
