SANKEN ELECTRIC CO.

,LTD

Selection Guide

IC for LED Lighting

The all contents in this document are as of date of publication.

Make sure that this is the latest revision of the document before
use. Please check the details of the product by data sheet.
http://www.sanken-ele.co.jp/en

LEDIC-SGE Aug. 31, 2015 P.1

Table of Contents

 LED Driver IC Overview P.3

Application
• Off-line Non-isolated Buck Type (Low Power Application) P.4
• Off-line Non-isolated Buck-boost Type (Low Power Application) P.5
• Off-line Flyback Type (Low to Middle Power Application) P.6
• DC/DC converter P.7
• High Power and Smart Application P.8
LED Driver Lineup for Small LED Lighting (Non-isolated) P.9
Class-C Support LED Driver Lineup (Flyback) P.12
DC/DC LED Driver Lineup P.16
IC Lineup for High Power and Smart LED Lighting P.22
IMPORTANT NOTES P.26

LEDIC-SGE Aug. 31, 2015 P.2

 LED Driver IC Overview
Back to contents

Downsized PCB High Power and Smart Lighting

LED bulb Down light LED fluorescent lamp
Spot light Ceiling light Street light
MR16

DC/DC Isolated  PFC Circuit- less

LC57xx AC/DC Flyback Convertor Class-C Support at Light Load
series
DIP8
LC5540LD LC5540LF TO-220F
SOP8
SOIC8
(Exposed)
Non-isolated Buck and Buck-boost Convertor High Power & Smart Application
PFC : CRM, CCM and DCM control ICs
LC5560LD DIP8
(Buck / Buck-boost / Flyback, Class-C support) Main SMPS : LLC control ICs
LC5550LD Auxiliary SMPS :
DIP8 PWM control ICs, LC201S
(Buck, Class-C support)
Microcomputer: MD660x (8bit MCU)
LC5220  Low Component Count
(Buck / Buck-boost )  High Power Factor DC/DC LED Driver
SOP8 DIP8 BL Series (1ch,2ch) External MOSFET
LC57xx Series(1ch) Integrated MOSFET
Support Wide Power Range and Several Form Lamps.
LC100x series (1ch) Balancer
LEDIC-SGE Aug. 31, 2015 P.3
 Off-line Non-isolated Buck Type (Low Power Application)
Back to contents

Small PCB

VAC
LC5220 series →P.10
SOP8 DIP8
 LED bulb

LED Driver

Freewheel diode

Class-C support and input capacitor less

LC5550LD series →P.11

VAC

LED Driver
LC5560LD series →P.15
DIP8
 LED bulb
 Down light
 LED fluorescent lamp
Notes:
See the Selection Guide of diode about
Freewheel diode peripheral diodes.

LEDIC-SGE Aug. 31, 2015 P.4

 Off-line Non-isolated Buck-Boost Type (Low Power Application)
Back to contents

Small PCB

VAC
LC5220 series →P.10
SOP8 DIP8
 LED bulb

LED Driver

Freewheel diode

Class-C support and input capacitor less

LC5560LD series →P.15

VAC

LED Driver  LED bulb

DIP8 SOP8
 Down light
 LED fluorescent lamp

Notes:
See the Selection Guide of diode about
Freewheel diode peripheral diodes.

LEDIC-SGE Aug. 31, 2015 P.5

 Off-line Flyback Type (Low to Middle Power Application)
Back to contents

VAC
Snubber diode Secondary rectification diode

OVP
LED Driver Control

Cont.
Average
Current
Control

GND

Photo
lsolator

LED Driver with Integrated Power MOSFET

LC5560LD series (Non-isolated)  LED bulb, down light and LED fluorescent lamp →P.15
DIP8
LC5540LD series (Isolated)  Down light and LED fluorescent lamp →P.14
DIP8
LC5540 LF series (Isolated)  Ceiling light and street lamp →P.13

TO-220F-7L
Notes:
See the Selection Guide of diode about peripheral diodes.

LEDIC-SGE Aug. 31, 2015 P.6

 DC/DC converter Back to contents

Buck converter Boost converter

Freewheel diode Rectification diode
DC
DC

LED Driver
LED Driver
SOP8
LC5710S* →P.18

LC5720S* HSOP8 →P.19

(Exposed)
SOP8 →P.18
LC5710S*
SOIC8
LC5720S* →P.19
(Exposed)
Buck-boost converter
Freewheel diode BL0100A SOIC14 →P.20

DC
BL0200 SOP18 →P.21

LED Driver

SOP8
LC5710S* →P.18 Notes:
See the Selection Guide of diode about peripheral diodes.
HSOP8 →P.19
LC5720S* (Exposed)
*Built-in power MOSFET.

LEDIC-SGE Aug. 31, 2015 P.7

 High Power and Smart Application Back to contents

Bypass diode for PFC

VAC
Rectification diode for PFC

Bootstrap diode
DC/DC LED driver
→P.16
REG

PFC LLC Control IC

Control
IC VS

LED
Driver
PFC
Error
Amp.

FB GND

PFC control ICs Microcomputer

Main convertor Microcomputer

Secondary
LLC control ICs Photo
lsolator
rectification diode →P.24
Snubber VOUT

Auxiliary power supply

Auxiliary power
supply IC Error
Amp.

PWM control ICs Cont.

LC201S →P.23 FB GND GND

For non-isolated circuit,

built-in linear regulator
Photo
lsolator

Notes:
See the Selection Guide of diode about peripheral diodes.
See the Selection Guide of AC/DC Convertor and PFC about PFC, LLC and PWM ICs.

LEDIC-SGE Aug. 31, 2015 P.8

 LED Driver Lineup for Small LED Lighting (Non-Isolated) Back to contents

 Non-isolated type LED bulb Down light LED fluorescent lamp

 AC/DC driver
 High power factor AC/DC LED driver

Series VIN(MAX) Package Application Feature Link

LC5220 250V/450V SOP8 DIP8 LED bulb ・Buck / buck-boost
・PWM dimming
P.10

LC5550LD 250V DIP8 LED bulb ・Buck

Down light ・Class-C support
LED fluorescent lamp ・Input electrolytic capacitorless P.11

LC5560 650V DIP8 LED bulb ・Buck / buck-boost

Down light ・Flyback
LED fluorescent lamp ・Class-C support P.15
・Input electrolytic capacitorless
・Dimming

LEDIC-SGE Aug. 31, 2015 P.9

ILED= 0.5A and 1.0A , VIN(MAX)= 250V and 450V
Non-isolated Buck and Buck-boost LED Driver IC
LC5220 Series Back to Lineup

SOP8 DIP8 Lineup

MOSFET
Part Number IO(MAX) Package
VDSS RDS(ON)
LC5222D DIP8
 Buck and buck-boost 250V 2.2Ω
LC5222S SOP8
 SLEEP Function 0.5A
LC5225D DIP8
 ENABLE Function 450V 6Ω
LC5225S SOP8
 PWM Dimming Function
LC5223D 250V 1.3Ω DIP8
 Protection functions 1.0A
UVLO LC5226D 450V 3Ω DIP8
OPP* and OCP are latched shutdown
Pin arrangement
TSD is auto restart
*OPP : Protection when a free-wheeling diode is open
Pin No. DIP8 SOP8

Typical application circuit (Buck type) 1 REG REG

2 PWM PWM
3 REF REF
4 SEN SEN
5 OUT OUT
6 VBB OUT
7 － VBB
8 GND GND

LEDIC-SGE Aug. 31, 2015 P.10

Input Electrolytic Capacitorless, IEC61000-3-2 Class-C Support
Non-isolated Buck LED Driver IC
LC5550 Series Back to Lineup

DIP8 Lineup
PWM MOSFET POUT
Package Part Number
freq. VDSS(min.) RDS(ON)(max.) AC230V Universal

 Buck LED driver LC5555LD 72 kHz 3.95 Ω 10W 8W

DIP8 650V
 Input electrolytic capacitorless LC5556LD 60 kHz 1.9 Ω 16W 13W
 High accuracy output current, ±5%
 PWM and quasi-resonant topology
 High efficiency
 High power factor (IEC61000-3-2 class-C support) Pin arrangement
 Universal input Pin No. Symbol Function

 Protection functions 1 S/GND MOSFET source and GND pin

OCP is Pulse-by-pulse Supply voltage input and OVP signal
2 VCC
input
OLP, OVP and TSD are latched shutdown OCP, QR signal input and OVP signal
Typical application circuit (PWM type) 3 OCP
R1 D6
input
R2
4 COMP Feedback phase-compensation input
U1

NF
5 LC5550LD 4
COMP
5 NF No function
6 3 OCP/BD
Contro1

6 ISENSE Output current sensing voltage input

ISEN
VCC
2 R5
D4 C3 C4 C5 C6
D3
D/ST S/GND C2
VAC 8 1

D1 D2
R3 R4 T1
7 ― Pin removed
C1 MOSFET drain pin and input of the
C7
LED
8 D/ST
D5
startup current

LEDIC-SGE Aug. 31, 2015 P.11

 Class-C Support LED Driver Lineup (Flyback) Back to contents

 Power factor Class-C support Ceiling light Street light

 Off-line LED driver
 High power factor at low power state
 Isolated and non-isolated type

LED bulb LED fluorescent

Down light
lamp

Series VIN(MAX) Package Application Feature Page

LC5540LF 650V / 800V TO-220F Ceiling light ・Isolated type
Street light P.13

LC5540LD 650V / 800V DIP8 Down light ・Isolated type

LED fluorescent lamp P.14

LC5560 650V DIP8 LED bulb ・Non-isolated type

Down light ・Dimming P.15
LED fluorescent lamp

LEDIC-SGE Aug. 31, 2015 P.12

Input Electrolytic Capacitorless, IEC61000-3-2 Class-C Support
High Efficiency Isolated LED Driver IC
LC5540LF Series Back to Lineup

TO-220F-7L Lineup
MOSFET POUT
Part Number PWM freq.
VDSS RDS(ON) AC230V Universal
LC5546LF 40kHz 1.9Ω 60W 40W
650V
 Input electrolytic capacitorless LC5547LF 40kHz 1.1Ω 80W 55W
 Quasi-resonant topology
LC5549LF 40kHz 800V 1.7Ω 60W 40W
 High efficiency, low noise
 High power factor (IEC61000-3-2 class-C support)
at light load Pin arrangement
 Protection functions Pin Symbol Function
OCP is pulse-by-pulse No.
OLP, OVP and TSD are latched shutdown MOSFET drain pin and input of
1 D/ST the startup current
Typical application circuit
2 S/GND MOSFET source and GND pin
3 VCC Supply voltage input and OVP
signal input
4 OCP OCP, QR signal input and OVP
signal input
5 FB Feedback signal input and OLP
signal input
6 NC ―
7 OVP OVP signal input

LEDIC-SGE Aug. 31, 2015 P.13

Input Electrolytic Capacitorless, IEC61000-3-2 Class-C Support
High Efficiency Isolated LED Driver IC
LC5540LD Series Back to Lineup

DIP8 Lineup
MOSFET POUT
Part Number PWM freq.
VDSS RDS(ON) AC230V Universal
LC5545LD 72kHz 3.95Ω 13W 10W
650V
 Input electrolytic capacitorless LC5546LD 60kHz 1.9Ω 20W 16W
 Quasi-resonant topology
LC5548LD 72kHz 800V 3.5Ω 13W 10W
 High efficiency, low noise
 High power factor (IEC61000-3-2 class-C support) Pin arrangement
at light load Pin Symbol Function
No.
 Protection functions
OCP is pulse-by-pulse 1 S/GND MOSFET source and GND pin
OLP, OVP and TSD are latched shutdown Supply voltage input and OVP
2 VCC signal input
Typical application circuit OCP, QR signal input and OVP
3 OCP signal input
4 FB Feedback signal input and OLP
signal input
5 NF No function
6 OVP OVP signal input
7 ― Pin removed
8 D/ST MOSFET drain pin and input of
the startup current

LEDIC-SGE Aug. 31, 2015 P.14

Input Electrolytic Capacitorless, IEC61000-3-2 Class-C Support
High Efficiency Non-Isolated LED Driver IC
LC5560LD Series Back to Lineup

DIP8 Lineup
PWM MOSFET POUT
Part Number
freq. VDSS(min.) RDS(ON)(max.) AC230V Universal
 Buck / Buck-boost / Flyback LC5565LD 72 kHz 3.95 Ω 13 W 10 W
650V
 Input electrolytic capacitorless LC5566LD 60 kHz 1.9 Ω 20 W 16 W
 Quasi-resonant topology
 High efficiency, low noise
Pin arrangement
 High power factor (IEC61000-3-2 class-C support)
Pin Symbol Function
at light load No.
 Dimming Function 1 S/GND MOSFET source and GND pin
 Protection functions
2 VCC Supply voltage input and OVP
OCP is pulse-by-pulse signal input
OLP, OVP and TSD are latched shutdown
3 OCP OCP, QR signal input and OVP
Typical application circuit (Flyback type) signal input
4 COMP Feedback phase-compensation
input
5 VREF Dimming control signal input
6 ISENSE Output current sensing voltage
input
7 ― Pin removed
8 D/ST MOSFET drain pin and input of
the startup current

LEDIC-SGE Aug. 31, 2015 P.15

 DC/DC LED Driver Lineup Back to contents

 For smart LED lighting application Back Light MR16 Ceiling light Street light

 For LED back light application Display

 Individual channels control

Series Output VIN(MAX) IO VLED(MAX) Package Feature Page

LC100x 35V 150mA 35V SOT89 Balancer
1ch P.17
(Balancer) 17V 250mA 17V
SOP8 Buck / buck-boost /boost
LC5710S 1ch 58V 1.0A 58V PWM dimming P.18
Built-in power MOSFET

SOIC8(Exposed) Buck / buck-boost /boost

LC5720S 1ch 50V 2.0A 50V PWM dimming P.19
Built-in power MOSFET

SOIC14 Boost circuit

High contrast proportion
BL0100 1ch ― ― ― PWM dimming P.20
Analog dimming

SOP18 Boost circuit

High contrast proportion
BL0200 2ch ― ― ― PWM dimming P.21
Analog dimming

LEDIC-SGE Aug. 31, 2015 P.16

ILED = 150 mA / 250 mA
LED Current Balancer IC
LC100x Series Back to Lineup

SOT89 Lineup
Part Number ILED(MAX) VLED MAX VIN VFB
LC100x 250 mA 17 V 2.4 V to 17 V 1.25 V
LC101x 150 mA 35 V 2.4 V to 35 V 200 mV ± 3%
 Current balancer between LED strings
 SOT89 small package Typical application circuit
Power dissipation PD = 0.75W
 Capacitorless of Input and output (LC101x)
 Difference between input and output voltage
ΔVDIF = 300 mV (max.)
 Protection functions
- OCP
- TSD activates at 130°C (without thermal hysteresis)

Pin arrangement
Pin No. Symbol Function
1 FB Feed back signal input
2 LO IC ground
3 NC ―
4 IN Constant current source input
5 LED Output

LEDIC-SGE Aug. 31, 2015 P.17

ILED = 1.0 A VIN = 5 V to 58 V
LED Driver for Buck, Buck-boost and Boost LED Driver
LC5710S Back to Lineup

SOP8 MOSFET
Part Number ILED(MAX) VIN fOSC
RDS(ON)
LC5710S 1.0A 5 ~ 58V 0.550Ω(typ.) 100k ~ 500kHz

Pin arrangement
 For buck, boost and buck-boost circuit
Pin No. LC5710S Functions
 ILED = 1.0 A (max.)
1 COMP Phase compensation
 fOSC = 100 kHz to 500 kHz (adjustable)
2 RT Frequency adjust
 VCS = 100 mV ± 3 %
3 GND Ground
 High accuracy dimming control
4 SW Switch output
PWM : 20 kHz(max.)
DC: 0.2 V to 2 V 5 VIN DC input
 Protection functions 6 CSP LED current sense (+)
UVLO, OCP, TSD, LED OVP, LED Open and LED Cross Connection 7 CSN LED current sense (-)
8 DIM Dimming signal input
Typical application circuit

Boost Buck-boost Buck

LEDIC-SGE Aug. 31, 2015 P.18
ILED = 2.0 A VIN = 8.5 V to 50 V
LED Driver for Buck, Buck-boost and Boost LED Driver
LC5720S Back to Lineup

SOIC8(Exposed) MOSFET
Part Number ILED(MAX) VIN fOSC
RDS(ON)
LC5720S 2.0A 8.5 ~ 50V 0.215Ω(typ.) 500kHz

 For buck, boost and buck-boost circuit Pin arrangement

 ILED = 2.0 A Pin No. Symbol Function
 fOSC = 500 kHz 1 COMP Phase compensation pin
 VCS = 100 mV±5 % 2 NC ―
 High efficiency η > 90 %(typ.) 3 GND Ground pin
 PWM dimming : 20 kHz(max.) 4 SW Output pin
 Protection functions 5 VIN DC input pin
OCP is pulse-by-pulse 6 CSP Reference input pin of current detection
OVP and TSD are auto restart 7 CSN Negative input pin of current detection
8 DIM PWM dimming signal input pin
Typical application circuit
Input
voltage

5 6
VIN CSP
CIN
RCS
LC5700S COUT
7
CSN
ROVP
8 Output
DIM DS LED
voltage
DZOVP
1 4
COMP SW
GND L
CS
3
CP
RS
Buck Buck-boost Boost

LEDIC-SGE Aug. 31, 2015 P.19

1ch Boost Convertor
LED Back Light Driver
BL0100A Series Back to Lineup

SOIC14 Lineup
LED open/short
Error Signal Enable
Products VREG Accuracy protection and
Output Function
OVP operations
BL0100A Yes − ±2% Auto restart

Features and Benefits

 Boost DC/DC topology → Low power dissipation
 Individual control of boost circuits Typical application circuit
 No requirement of VF screening
BL0100A
Boost convertor VCC DRV
• Current mode type PWM control
VREF OC
• Internally-fixed PWM frequency is 200 kHz PWM
• Maximum on duty is 90 %
ER
LED current control OVP
• PWM dimming FSET
SW
• Analog dimming REG
COMP
• High accuracy output current IFB
GND
• Error signal output
• IC Enable Function (BL0102A and BL0104A) TC_BL0100A_1_R1

Protection Functions
• OCP of boost circuit and LED output are pulse-by-pulse
• OVP and Output Open/Short Protection are latched shut down or auto restart
• TSD is auto restart

LEDIC-SGE Aug. 31, 2015 P.20

2ch Boost Convertor
LED Back Light Driver
BL0200 Series Back to Lineup

SOP18 Lineup
Boost MOSFET Error signal Enable VCC(ON) VCC(OFF)
Part Number VREG Accuracy
fOSC output Function (typ.) (typ.)

BL0200C 200 kHz Yes 〓 ±2% 9.6 V 9.1 V

BL0202B 100 kHz

〓 Yes ± 1.5 % 9.6 V 8.6 V
BL0202C 200 kHz
Features and Benefits
 Boost DC/DC topology → Low power dissipation Typical application circuit
 Individual control of boost circuits
 No requirement of VF screening BL0202B/C
VCC DRV1

Boost convertor VREF OC1

PWM1
• Current mode type PWM control PWM2 SW1
• Internally-fixed PWM frequency is 200 kHz
EN
• Maximum on duty is 90 % IFB1
Individual
LED current control control
• Separately controlled PWM dimming DRV2
• Analog dimming
• High accuracy output current OC2

• Error signal output (BL0200C) REG

• IC Enable Function (BL0202B and BL0202C) COMP1
OVP
SW2
COMP2
Protection Functions GND IFB2
• OCP of boost circuit and LED output are pulse-by-pulse
• OVP, TSD and Output Open/Short Protection are auto restart TC_BL0202_1_R1

LEDIC-SGE Aug. 31, 2015 P.21

 IC Lineup for High Power and Smart LED Lighting Back to contents

AC PFC Main power supply

 POUT ≥ 80 W
 For Using Microcomputer →P.15
PFC DC/DC
Ceiling light LLC IC
IC LED Driver LED
with microcomputer Down light

PWM
Auxiliary power supply
Street lump dimming
PWM IC
Dimming
/LC201S
Microcomputer Illuminance/
human body
sensor

Application Feature Products Page

CRM control, CCM control
PFC PFC ICs
DCM control (Interleaved)
Main convertor  Low noise LLC control ICs
See the Selection Guide of PFC and AC/DC
 PWM control
convertor
 Low power consumption at no
load < 25mW PWM control ICs
Auxiliary power  Flyback type
supply  Buck type (non-isolated)
 Built-in linear regulator
LC201S P.23
 For non-isolated circuit
 8 bit MCU
Microcomputer  High Performance DSP MD660x Series P.24
 High Resolution PWM

LEDIC-SGE Aug. 31, 2015 P.22

VO=5V Off-Line Linear Regulator
LC201S Back to Lineup

SOP8 LC201S output voltage

Output pin SL pin VOUT IOUT(max)
Open 9V 1.5 mA
OUT1
GND 20 V 1.5 mA
LC201S is a power supply IC for a microcontroller. OUT2 ― 5V 10 mA*
It is a linear regulator with startup circuit. Typical application circuit *with auxiliary winding
 Low component count (built-in startup circuit) Without auxiliary winding
 Either ST pin or auxiliary winding can be used for power supply of BR1
control circuit. VAC

6 5
 Power consumption of the startup circuit is zero.
8 7

C1 ST NC NC OUT1
(with auxiliary winding) U1
LC201S
 UVLO Function: GND SL SINK OUT2
C2

If OUT1 pin voltage decreases, OUT2 pin fixed to Low state 1 2 3 4 Microcontroller

Pin assignment R1 C3

Pin No. Symbol Function

With auxiliary winding
1 GND Ground Main power supply
Lamp
circuit for Lamp

2 SL Switch of OUT1 pin voltage

If OUT1 pin voltage is decreased, SINK pin flows sink current. Connect
3 SINK BR1
with OUT2 pin. VAC
D1
4 OUT2 Output of 5 V (Typ.) 8 7 6 5

C1 ST NC NC OUT1
Output of 9 V (Typ.) or 20 V (Typ.) . When auxiliary winding is
5 OUT1 U1
connected to OUT1 pin, OUT1 pin is power supply of the control circuit. LC201S
C2
6, 7 (NC) No function. This pin is Open GND SL SINK OUT2

Startup current input. When auxiliary winding is not connected to OUT1 1 2 3 4 Microcontroller
8 ST
pin, ST pin is power supply of the control circuit. R1 C3

LEDIC-SGE Aug. 31, 2015 P.23

Rich Analog, High Performance DSP and High Resolution PWM
8 bit MCU for Digital Controlled Power Supply System and High Speed Control
MD660x Series Back to Lineup

MD660x is 8 bit MCU (Micro Controller Unit) for the power control application such as digital control power supply system.
 Rich Analog Component Direct ADC Input Unity/Gain/Amp Insert 【 Block Diagram 】
：Analog section ：Digital section
Interconnections among Input A/D Input
A/D
Analog GPIO（Analog/Digital） General purpose operating amplifier
analog components and High-speed 10-bit
Successive approximation Digital GPIO（5V tolerant) ・ Gain switching between standalone and unity
external pins are configurable Type A/D converter
GPIO Wiring among analog blocks
Non-inverting Amplifier Circuit 〒 Comparator
by programmable analog Op-amp Comparator
Voltage Reference
General + + + +
are programmable.
All I/O signals of the analog
Temperature Sensor High- High- - - - -
purpose
network. MD660x has A/D Input
A/D Interrupt
High-precision 12-bit
speed speed
10-bit
Op-amp block can be wired with
events 10-bit external pins.
converter, analog comparators, Successive approximation ADC ADC +
-
+
-
+
-
+
-
+
-
+
-

D/A Type A/D converter High-speed Comparator

general purpose OPAMPs. High-precision
High-speed analog

GPIO
GPIO
12-bit
Built-in RAM Voltage DAC comparator
SAR ADC
 High Performance DSP Operations Built-in FLASH Memory
TinyDSP D/A converter
MD660x has 8 bit CPU and two 16 bit Tiny DIV MUL FLASH RAM IRC/POR
(for 1unit)

Register file
8-bit 8051CPU Internal Reference Oscillator
DSP. CPU controls systems, Tiny DSP does ・ Pipeline control 8051
Tiny Tiny HiRes
Timer Power On Reset
ALU ・1-Wire debug I/F CPU
calculations. Thus, parallel processing SFT ・256 byte RAM DSAC
DSP DSP PWM SPI, I2C
UART
Low Voltage Detector

Low power consumption mode

achieves. ACC (36bit) Automatic data transfer GPIO
among peripheral registers
General-purpose 16-bit Timer
DMA Capability Between Peripherals (DSAC)
Automatic data transfer among the Tiny DSP（for digital filtering etc.）
High-resolution PWM
・ Multiplication, product-sum operation, Serial communications System control
registers of the built-in peripheral Self-Running Feedback Controls shifting, and high-speed division
・Dead time
・SPI, I2C, UART Interrupt control
auto ・Duty Cut/Cycle Cut
・ 16-bit fixed point arithmetic
functions. Also, automatic data ADC auto
PWM
transfer among the A/D converter, auto DSP  Development Support Software
ADC
the Tiny DSP, and the PWM. ・IDE_MS660x : Program Development Environment
Feedback control can be applied System Tasks ・SKDSP : Digital Filters for Tiny DSP
without the CPU, so that the CPU CPU Program generation for the phase compensator
will focus on system processing such  Development Support Hardware
as anomaly detection or ・OCD I/F board (Interface for writing flash)
communications processing. ・CHEWING GUM (Evaluation board)
 System Support Functions CHEWING GUM
FLASH Memory, Timer, Serial Communications,
Oscillators, Reset Circuits, etc.

LEDIC-SGE Aug. 31, 2015 P.24

 Rich Analog, High Performance DSP and High Resolution PWM
8 bit MCU for Digital Controlled Power Supply System and High Speed Control
MD660x Series
Package Product Specification * Packing specifications is reel. The others are tray.
LQFP-44 LQFP-64 QFN-40 MD6601FNVL* MD6602FNVL*
Parameter MD6601FLV MD6602FPV
MD6601FNV MD6602FNV

Common
Package QFN-40 LQFP-44 QFN-40 LQFP-64
Power Digital : 150mW Digital : 165mW
Consumption(Typ.) Analog : 20mW Analog : 20mW
10×10 (0.8pitch) 10×10 (0.5pitch) 6×6 (0.5pitch) 10 bit A/D Converter 2 units, 4MSPS / unit, Dual Sample-hold mode
12 bit A/D Converter 1 unit, 1MSPS / unit

Analog Function
Unit : mm
 Power Supply Voltage D/A Converter 12 bit voltage output × 1ch 10 bit voltage output × 4 ch
Digital DVCC：3.3V Analog Comparator 4 units 6 units
Analog AVCC：3.3V General Purpose OPAMP 2 units 4 units
 Operation Frequency Voltage Reference 1.2 V output, middle point analog ground
50MHz(max.) Temperature Sensor The voltage according to temperature is output and is read by A/D converter.
8 bit 8051CPU 8051／8052 instruction compatible, execution cycle : 1 cycle (min.), 3 cycle (avg.)
 Analog Function
FLASH Memory 16 KB 32 KB
Analog interconnection : User configurable
Internal RAM 1 KB ( + fast RAM(256B) directly connected to CPU)
High speed analog comparator
2 unit, 16 bit 2 unit, 16 bit
General OPAMP : Stand-alone, unity gain selectable Tiny DSP
（MUL, MAC, DIV） ( Min./Max. saturation, constant register)
 Digital Function High Resolution PWM 2 phase PWM × 4 pairs, 1ns resolution (for duty and cycle), Duty Cut, Cycle Cut
Digital GPIO : 5V tolerant DSAC 8ch 16ch
Digital Function

FLASH memory with Cache Function and Security 16 bit Timer

2 units, 16 bit counter 4 units, 16 bit counter
Generates Interrupts Output Compare / Input Capture
Function
Each 1 unit
One wire Debug Interface SPI / I2C / UART Each 1 unit
(Individual configurable)
The reading and writing of internal resource, the
Digital × 12 Digital × 12 Digital × 26
control of execution, the break of program execution GPIO
Analog × 16 Analog × 16 Analog × 20
and the writing of FLASH can be processed by one
WDT 1 unit (Watch Dog Timer to generate internal reset or interrupt request)
wire debug line.
LVD Low voltage detection
Interrupt Controller POR Power on reset circuit
Interrupt priority of 2 level, Independent vectors for
IRC Internal reference clock generator (10MHz)
each interrupt source, all GPIO can be set interrupt
PLL Frequency multiplication by 4 of external (crystal) clock, IRC clock (50 MHz max.)
input.

LEDIC-SGE Aug. 31, 2015 P.25

 IMPORTANT NOTES
 The contents in this document are subject to changes, for improvement and other purposes, without notice. Make sure that this
is the latest revision of the document before use.
 Application examples, operation examples and recommended examples described in this document are quoted for the sole
purpose of reference for the use of the products herein and Sanken can assume no responsibility for any infringement of
industrial property rights, intellectual property rights, life, body, property or any other rights of Sanken or any third party which
may result from its use.
 Unless otherwise agreed in writing by Sanken, Sanken makes no warranties of any kind, whether express or implied, as to the
products, including product merchantability, and fitness for a particular purpose and special environment, and the information,
including its accuracy, usefulness, and reliability, included in this document.
 Although Sanken undertakes to enhance the quality and reliability of its products, the occurrence of failure and defect of
semiconductor products at a certain rate is inevitable. Users of Sanken products are requested to take, at their own risk,
preventative measures including safety design of the equipment or systems against any possible injury, death, fires or damages to
the society due to device failure or malfunction.
 Sanken products listed in this document are designed and intended for the use as components in general purpose electronic
equipment or apparatus (home appliances, office equipment, telecommunication equipment, measuring equipment, etc.).
When considering the use of Sanken products in the applications where higher reliability is required (transportation equipment
and its control systems, traffic signal control systems or equipment, fire/crime alarm systems, various safety devices, etc.), and
whenever long life expectancy is required even in general purpose electronic equipment or apparatus, please contact your
nearest Sanken sales representative to discuss, prior to the use of the products herein.
The use of Sanken products without the written consent of Sanken in the applications where extremely high reliability is required
(aerospace equipment, nuclear power control systems, life support systems, etc.) is strictly prohibited.
 When using the products specified herein by either (i) combining other products or materials therewith or (ii) physically,
chemically or otherwise processing or treating the products, please duly consider all possible risks that may result from all such
uses in advance and proceed therewith at your own responsibility.
 Anti radioactive ray design is not considered for the products listed herein.
 Sanken assumes no responsibility for any troubles, such as dropping products caused during transportation out of Sanken’s
distribution network.
 The contents in this document must not be transcribed or copied without Sanken’s written consent.

LEDIC-SGE Aug. 31, 2015 P.26