Scribd
Upload
52 views1 page

Jet-Lube FMG Grease 2

The document describes a food grade grease called FMGTM. It is an aluminum complex grease designed for use in food processing where it may have incidental food contact. The grease is extremely water resistant, has polymer additives for strength, and can be used in a wide temperature range from 0°F to over 400°F.

Uploaded by

Don Howard
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
52 views1 page

Jet-Lube FMG Grease 2

The document describes a food grade grease called FMGTM. It is an aluminum complex grease designed for use in food processing where it may have incidental food contact. The grease is extremely water resistant, has polymer additives for strength, and can be used in a wide temperature range from 0°F to over 400°F.

Uploaded by

Don Howard
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

FMG™

FOOD MACHINERY GREASE

DESCRIPTION
PRODUCT CHARACTERISTICS
FMG™ is an aluminum complex grease lubricant of the USDA
Authorized H-1 type. It meets or exceeds the requirements of Thickener Aluminum Complex
CFR Title 21, Section 178.3570 of FDA Regulations and is Fluid Type White Oils & Synthetic
specifically designed for use in the food processing industry
where it may have incidental food contact. FMG has been Color/Appearance White Grease
formulated to perform in a wide variety of operating conditions.
Specific Gravity 0.94
It is extremely water resistant and will remain in place even
after frequent wash downs. Polymer additives provide Density (lb/gal) Typical 7.80
adhesive/cohesive strength to protect against pound-off when
shock loads are encountered. Additive Type Zinc Sulfide & Organic
R&O
FMG can be used in a wide range of temperatures from 0°F (- Dropping Point (ASTM D-566) >500°F (260°C)
18°C) to over 400°F (204°C). It is recommended for the
lubrication of roller, needle, ball, journal, and sliding bearings Flash Point °F (°C) (ASTM D-92) >430 (221)
in the food processing and handling industry. Autoignition Point >500°F (260°C)
(CALCULATED)
NLGI Grade 2
FEATURES Penetration @ 77°F 265 – 295
1
• Aluminum Complex Grease (ASTM D-217) mm x 10
• Polymer Additives Copper Strip Corrosion 1A
• Non-Pound Out Formula
(ASTM D-4048)
• Bacteriostatic Agent
• Anti-Wear Additives 4-Ball (ASTM D-2596)
Weld Point, kgf 400-500
Load Wear Index 50
BENEFITS Wear Scar Diameter 0.7

• Extremely Water Resistant


Oxidation Resistance <5.0
• Adhesive/Cohesive Strength (ASTM D-942) PSI Drop, 100 hrs.
• Reduced Lube Consumption Base Oil Viscosity 90 – 110
• Retards Bacteria/Fungus Growth
(ASTM D-445) cSt @ 40°C
• Available in Other Grades

NSF (H-1) Registered No. 048226. Conforms to FDA


Regulations CFR 21 Section 178.3570 for Incidental Food For package types and part numbers
Contact.
contact [email protected].

LIMITED WARRANTY

For warranty information please visit


http://www.jetlube.com/pdf/Jet-Lube_Warranty.pdf

You can also email us at [email protected] or write


to the Sales Department at the address below.

930 Whitmore Drive • Rockwall, Texas 75087 • USA • (972) 771-1000 • 800-699-6318 • www.jetlube.com • An ISO 9001 registered company
2/18 – Revised 6/18

You might also like