Amplitude Modulation

1
 Content

• What is Modulation
• Amplitude Modulation (AM)
• Demodulation of AM signals
• Calculation and Examples
• Summary

2
 What is Modulation
• Modulation
– Amplitude Modulation is a process where the amplitude of
a carrier signal is altered according to information in a
message signal.
– The frequency of the carrier signal is usually much greater
than the highest frequency of the input message signal.

• Why Modulation
– Reduce Antenna Size
– Suitable for signal transmission (distance…etc)
– Multiple signals transmitted on the same channel
– Capacitive or inductive devices require high frequency AC
input (carrier) to operate.
– Stability and noise rejection
3
 About Modulation
• Application Examples
– broadcasting of both audio
and video signals.
– Mobile radio communications,
such as cell phone.

• Basic Modulation Types

– Amplitude Modulation: changes the amplitude.
– Frequency Modulation: changes the frequency.
– Phase Modulation: changes the phase.

4
 AM Modulation/Demodulation
Source Sink
Channel

Modulator Demodulator

Baseband Signal Bandpass Signal Original Signal

with frequency with frequency with frequency
fm fc fm
(Modulating Signal) (Modulated Signal)
fc >> fm
Voice: 300-3400Hz GSM Cell phone: 900/1800MHz
5
 AM Modulation Scheme

Ac cos wc t k

mt  k + X s t 

1
 AM – Basic Definitions
The amplitude of high-carrier signal is varied according to the
instantaneous amplitude of the modulating message signal m(t).
5
The AM signal
s t   Ac 1  k  mt cos wct 0

-5
0 0.01 0.02 0.03 0.04 0.05 0.06 0.07 0.08 0.09 0.1
1

The modulating signal: mt  0

-1
0 0.01 0.02 0.03 0.04 0.05 0.06 0.07 0.08 0.09 0.1
The Carrier Signal: 1

ct   Ac cos wc t 0

-1
0 0.01 0.02 0.03 0.04 0.05 0.06 0.07 0.08 0.09 0.1
* AM Signal Math Expression*
• Mathematical expression for AM: time domain
S AM ( t )  Ac [1  k cos( w m t )] cos( w c t )
• expanding this produces:
SAM (t )  Ac cos(wct )  Ac k cos(wmt ) cos(wc t )
using : cos A cos B  1
2 cos( A  B )  cos( A  B ) 
SAM (t )  Ac cos(wc t )  Ac k / 2 cos(wc  wm )t  Ac k / 2 cos(wc  wm )t
• In the frequency domain this gives:
Carrier, Ac =1.
Amplitude k/2
k/2
frequency

lower fc-fm fc fc+fm

sideband upper sideband 8
 AM Power Frequency Spectrum
• AM Power frequency spectrum obtained by
squaring the amplitude:
Carrier, A2=12 = 1
Power

k2/4 k2/4

fc-fm fc fc+fm freq .

2 2
k k
 A 2  
• Total power for AM: 4 4
k 2
 1 
2
9
 Amplitude Modulation
• The AM signal is generated using a
multiplier.
• All info is carried in the amplitude of
the carrier, AM carrier signal has
time-varying envelope.
• In frequency domain the AM
waveform are the lower-side
frequency/band (fc - fm), the carrier
frequency fc, the upper-side
frequency/band (fc + fm).
10
 AM Modulation – Example
• The information signal is usually not a single
frequency but a range of frequencies (band). For
example, frequencies from 20Hz to 15KHz. If we
use a carrier of 1.4MHz, what will be the AM
spectrum?
• In frequency domain the AM waveform are the
lower-side frequency/band (fc - fm), the carrier
frequency fc, the upper-side frequency/band (fc +
fm). Bandwidth: 2x(15K-20)Hz.
1.4 MHz
frequency

1,385,000Hz to fc 1,400,020Hz to
1,399,980Hz 1,415,000Hz
11
Modulation Index of AM Signal
For a sinusoidal message signal m(t )  Am cos(2f mt )
Carrier Signal: cos(2 f ct ) DC: AC

Modulated Signal: S AM (t )  [ Ac  Am cos(2 f m t )]cos(2 f c t )

 Ac [1  k cos(2 f m t )]cos(2 f c t )
Am
k
Modulation Index is defined as: Ac
Modulation index k is a measure of the extent to
which a carrier voltage is varied by the modulating
signal. When k=0 no modulation, when k=1 100%
modulation, when k>1 over modulation.
12
Modulation Index of AM Signal

13
Modulation Index of AM Signal

CSULB May 22, 2006 14

Modulation Index of AM Signal

15
 Modulation Depth
2Amax = maximum peak-to-peak of waveform
2Amin = minimum peak-to-peak of waveform The image cannot be displayed. Your computer may not have enough memory to
open the image, or the image may hav e been corrupted. Restart your computer, and

Am
then open the file again. If the red x still appears, you may hav e to delete the image
and then insert it again.

k  as follows:
This may be shown to equal AC
The image cannot be displayed. Your computer may not hav e enough memory to open the image, or the image may hav e been corrupted. Restart your computer, and then open the
file again. If the red x still appears, you may hav e to delete the image and then insert it again.
The image cannot be displayed. Your computer may not hav e enough memory to open the image, or the image may hav e been corrupted. Restart your computer, and

2 Amax =2 AC + 2 Am
then open the file again. If the red x still appears, you may hav e to delete the image and then insert it again.

2Amin =2 AC  2 Am
The image cannot be displayed. Your computer may not hav e enough memory to open the image, or the image may hav e been corrupted. Restart your computer, and then open the file again. If the red x still appears, y ou may hav e to delete the image and then insert it again.

2 Amax  2 Amin Amax  Amin Am

k  
2 Amax  2 Amin AC AC
The image cannot be displayed. Your computer may not hav e enough memory to open the image, or the image may hav e been corrupted. Restart your computer, and then open the file again. If the red x still appears, y ou may hav e to delete the image and then insert it again.

Am

Ac

2Amin 2Amax

CSULB May 22, 2006 16

 High Percentage Modulation
• It is important to use as high percentage of
modulation as possible (k=1) while ensuring
that over modulation (k>1) does not occur.
• The sidebands contain the information and
have maximum power at 100% modulation.
• Useful equation
Pt = Pc(1 + k2/2)
Pt =Total transmitted power (sidebands and
carrier)
Pc = Carrier power

17
 AM – Modulation Efficiency

 Definition : The Modulation Efficiency is the percentage of the total power of the modulated signal that
conveys information.

Only “Sideband Components” – Convey information

Modulation Efficiency:
m2  t 
E 2
 100
1  m t 
Highest efficiency for a 100% AM signal : 50% - square wave modulation

Normalized Peak Envelope Power (PEP) of the AM signal:

Ac2
PPEP  1  maxmt 2
2
Voltage Spectrum of the AM signal:

Ac
S( f )    f  f c   M  f  f c     f  f c   M  f  f c 
2
Unmodulated Carrier Spectral Eeng 360
Translated Message Signal 18
Component
 Example
• Determine the maximum sideband power if the
carrier output is 1 kW and calculate the total
maximum transmitted power.

• Max sideband power occurs when k = 1. At this

percentage modulation each side frequency is ½
of the carrier amplitude. Since power is
proportional to the square of the voltage, each
has ¼ of the carrier power. ¼ x 1kW = 250W
Total sideband power = 2 x 250 = 500W. Total
transmitted power = 1kW + 500W = 1.5kW

19
 Example : Power of an AM signal

Suppose that a 5000-W AM transmitter is connected to a 50 ohm

load;
Then the constant Ac is given by 2
1 Ac Without
 5,000  Ac  707 V
2 50 Modulation
If the transmitter is then 100% modulated by a
1000-Hz test tone , the total (carrier + sideband)
average power will be

 1  Ac2   2 1 
  1.5  5000  7,500W  m t   for 100% modulation 
1.5  2 
2
  50 

The peak voltage (100% modulation) is (2)(707) = 1414 V

across the 50 ohm load.
 1  Ac2 
4    4  5000  20,000W
The peak envelope power 2
  50 
(PEP) is

2
The modulation efficiency would be 33% since < m (t) >=1/2
 Demodulation of AM Signals

Demodulation extracting the baseband message from

the carrier.

•There are 2 main methods of AM Demodulation:

• Envelope or non-coherent detection or demodulation.

• Square Law Detection
• Synchronised or coherent demodulation.

21
 Envelope/Diode AM Detector

If the modulation depth is > 1, the distortion below occurs

The image cannot be displayed. Your computer may not hav e enough memory to open the image, or the image may hav e been corrupted. Restart your computer, and then open the file again. If the red x still appears, y ou may hav e to delete the image and then insert it again.

K>1
22
 Square-
Square-Law Demodulation
s 2 t    Ac 1  k  m t cos w c t  
2
y t   .25 Ac 1  k  mt 
.5 Ac2 1  k  mt 
2
 .5 Ac2 1  k  mt 
2
cos 2w c t 
  mt   DCoffset 

s t  2 LPF  y t 

. 5 Ac2 1  k  m t 
2
 Synchronous or Coherent
Demodulation

This is relatively more complex and more expensive. The

Local Oscillator (LO) must be synchronised or coherent, i.e.
at the same frequency and in phase with the carrier in the
AM input signal.
24
 Coeherent Demodulation
s t    Ac 1  k  mt cos wct   cos wc t 
 Ac 1  k  mt  cos 2 wct 
 1  cos 2wc t 
 Ac 1  k  mt   
 2 
.5 Ac 1  k  mt   .5 Ac 1  k  mt cos 2wc t y t   .5 Ac 1  k  mt 
  mt   DCoffset 

s t  X LPF y t 

cos wct
Quadrature Operation
 Synchronous or Coherent
Demodulation
If the AM input contains carrier frequency, the LO or
synchronous carrier may be derived from the AM input.

27
 Synchronous or Coherent
Demodulation
If we assume zero path delay between the modulator and
demodulator, then the ideal LO signal is cos(wct).

VDC + mt cosωc t 

The image cannot be displayed. Your computer may not hav e enough memory to open the image, or the image may hav e been corrupted.
Restart y our computer, and then open the file again. If the red x still appears, you may hav e to delete the image and then insert it again.

Analysing this for a AM input =

28
 Coherent Detection
Assume zero path delay between the modulator and demodulator:
VX = AM input x LO
VDC + mt cosωc t   cosωc t 
The image cannot be displayed. Your computer may not hav e enough memory to open the image, or the image may hav e been corrupted. Restart your computer, and then open the file again. If the red x still appears, you may hav e to
delete the image and then insert it again.

=
The image cannot be displayed. Your computer may not hav e enough memory to open the image, or the image may hav e been corrupted. Restart your computer, and then

VDC + mt cos 2 ωc t 

open the file again. If the red x still appears, y ou may hav e to delete the image and then insert it again.

=
The image cannot be displayed. Your computer may not hav e enough memory to open the image, or the image may hav e been corrupted. Restart your computer, and then open the file again. If the red x still appears,
y ou may hav e to delete the image and then insert it again.

1 1 
= V DC + mt  + cos2ωc t 
2 2 
The image cannot be displayed. Your computer may not hav e enough memory to open the image, or the image may hav e been corrupted. Restart your computer, and then open the file again. If the red x still appears, y ou may hav e to delete the image and then insert it again.

VDC m  t  VDC m t 
Vx = + + cos  2ωc t  + cos  2ωc t 
2 2 2 2
Note – the AM input has been 'split into two' – ‘red part' has The image cannot be displayed. Your computer may not hav e enough memory to open the image, or the image may hav e been corrupted. Restart your computer, and then open the file again. If the red x still

moved or shifted up to higher frequency:  m  t  cos  2ωct  +VDC cos  2ωct  

appears, you may hav e to delete the image and then insert it again.

 2 The image cannot be displayed. Your computer may not have enough

VDC m  t 
memory to open the image, or the image may hav e been corrupted.
Restart your computer, and then open the file again. If the red x still
appears, you may hav e to delete the image and then insert it again.

and blue part shifted down to baseband: 2


2
29
Coherent Detection

30
 Diode v.s Coherent
1. Diode-: Unable to follow fast-modulation
properly
2. Diode-: Power is absorbed from the tuned
circuit by the diode circuit.
3. Diode-: Distortion produced is not acceptable
for some communications.
4. Diode+: Obviously simple, low cost.
5. Coherent+: Low Distortion
6. Coherent+: Greater ability to follow fast-
modulation.
7. Coherent+: The ability to provide power gain
8. Coherent-: Complex and expensive

31
 Exercises: Draw the Spectrums
a) cos(wct)cos(w1t)
from cosAcosB= 1/2[cos(A-B)+cos(A+B)]
we get: cos(wct)cos(w1t)=1/2[cos(wc-w1)t + cos(wc+w1)t]
Hence the spectrum of this is:
amplitude
1/2 1/2

wc-w1 wc+w1 frequency

b) cos2wt
from cos2A=1/2[1+cos2A]
1/2
we get: cos2wt=1/2[1+cos2wt] 1/2

The spectrum is thus:

DC=0Hz 2w freq

32
 Example
Suppose you have a portable (for example you carry it in your ' back
pack') AM transmitter which needs to transmit an average power of 10
Watts in each sideband when modulation depth k = 0.3. Assume that
the transmitter is powered by a 12 Volt battery. The total power will be
The image cannot be displayed. Your computer may not hav e enough memory to open the image, or the image may hav e been corrupted. Restart
The image cannot be displayed. Your computer may not hav e enough memory to open the image, or the image may hav e been corrupted. Restart your computer, and then open the file y our computer, and then open the file again. If the red x still appears, you may hav e to delete the image and then insert it again.
again. If the red x still appears, you may hav e to delete the image and then insert it again.

k k 2 2
where k2
PT = Pc + Pc + Pc Pc  10 Watts
4 4
The image cannot be displayed. Your computer may not hav e enough memory to open the image, or the image may hav e been corrupted. Restart your computer, and then open the file again. If the red x still appears, you may hav e to delete the image and
4
4 10 
then insert it again.

40
Pc =
2
= 2
 444.44 Watts
k  0.3
Hence, total power PT = 444.44 + 10 + 10 = 464.44 Watts.

Hence, battery current (assuming ideal transmitter) = Power / Volts =

The image cannot be displayed. Your computer may not have enough memory to open the image, or the image may hav e been
corrupted. Restart your computer, and then open the file again. If the red x still appears, you may hav e to delete the image and

464.44
then insert it again.

 Amps A large and heavy 12 Volt battery!!!!

12
Suppose we could remove one sideband and the carrier, power transmitted
would be 10 Watts, i.e. 0.833 amps from a 12 Volt battery, which is more
reasonable for a portable radio transmitter. (Single Side Band)
33
AM Transmitter and Receiver
The image cannot be displayed. Your computer may not hav e enough memory to open the image, or the image may hav e been corrupted. Restart your computer, and then open the file again. If the red x still appears, y ou may hav e to delete the image and then insert it again.

S AM t  = [ AC + Am c o s ω m t  ]c o s ω c t 
 Am 
 AC  1 + c o s ω m t   c o s ω c t 
 AC 
 A C 1 + k c o s  ω m t   c o s  ω c t 

34
AM Transmitter and Receiver

35
 Summary
• Modulation, Amplitude Modulation
• Modulation Index, Modulation Depth
• Demodulation of AM signals
• Calculation and Examples
• Math: AM Time domain+Frequency domain
• Calculation: AM Power, AM Demodulation

Next Class….
• DSB, SSB, VSB……
• FM, PM

36