® BUV298AV
NPN TRANSISTOR POWER MODULE
■ HIGH CURRENT POWER BIPOLAR MODULE
■ VERY LOW Rth JUNCTION CASE
■ SPECIFIED ACCIDENTAL OVERLOAD
AREAS
■ INSULATED CASE (2500V RMS)
■ EASY TO MOUNT
■ LOW INTERNAL PARASITIC INDUCTANCE
INDUSTRIAL APPLICATIONS:
■ MOTOR CONTROL
Pin 4 not connected
■ SMPS & UPS
■ WELDING EQUIPMENT
ISOTOP
INTERNAL SCHEMATIC DIAGRAM
ABSOLUTE MAXIMUM RATINGS
Symbol Parameter Value Unit
V CEV Collector-Emitter Voltage (V BE = -5 V) 1000 V
V CEO(sus) Collector-Emitter Voltage (I B = 0) 450 V
V EBO Emitter-Base Voltage (I C = 0) 7 V
IC Collector Current 50 A
I CM Collector Peak Current (t p = 10 ms) 75 A
IB Base Current 10 A
I BM Base Peak Current (t p = 10 ms) 16 A
P tot Total Dissipation at T C = 25 o C 250 W
o
T stg Storage Temperature -55 to 150 C
o
Tj Max. Operating Junction Temperature 150 C
o
V ISO Insulation Withstand Voltage (AC-RMS) 2500 C
October 2001 1/7
BUV298AV
THERMAL DATA
o
R thj-case Thermal Resistance Junction-case Max 0.5 C/W
R thc-h Thermal Resistance Case-heatsink With Conductive
o
Grease Applied Max 0.05 C/W
ELECTRICAL CHARACTERISTICS (Tcase = 25 oC unless otherwise specified)
Symbol Parameter Test Conditions Min. Typ. Max. Unit
I CER Collector Cut-off V CE = V CEV 0.4 mA
Current (R BE = 5 Ω) V CE = V CEV T j = 100 o C 2 mA
I CEV Collector Cut-off V CE = V CEV 0.4 mA
o
Current (V BE = -5V) V CE = V CEV T j = 100 C 2 mA
I EBO Emitter Cut-off Current V EB = 5 V 2 mA
(I C = 0)
V CEO(sus) ∗ Collector-Emitter I C = 0.2 A L = 25 mH 450 V
Sustaining Voltage V clamp = 450 V
h FE ∗ DC Current Gain I C = 32 A VCE = 5 V 12
V CE(sat) ∗ Collector-Emitter I C = 32 A IB = 6.4 A 0.35 1.2 V
Saturation Voltage I C = 32 A IB = 6.4 A T j = 100 o C 0.6 2 V
V BE(sat) ∗ Base-Emitter I C = 32 A IB = 6.4 A 1 1.5 V
Saturation Voltage I C = 32 A IB = 6.4 A T j = 100 o C 0.9 1.5 V
di C /dt Rate of Rise of V CC = 300 V R C = 0 tp = 3 µs 160 210 A/µs
On-state Collector I B1 = 9.6 A T j = 100 o C
V CE (3 µs) Collector-Emitter V CC = 300 V R C = 9.3 Ω 4.5 8 V
Dynamic Voltage I B1 = 9.6 A T j = 100 o C
VCE (5 µs) Collector-Emitter V CC = 300 V R C = 9.3 Ω 2.5 4 V
Dynamic Voltage I B1 = 9.6 A T j = 100 o C
ts Storage Time I C = 32 A V CC = 50 V 2.2 4.5 µs
tf Fall Time V BB = -5 V R BB = 0.39 Ω 0.2 0.4 µs
tc Cross-over Time V clamp = 450 V I B1 = 6.4 A 0.45 0.7 µs
o
L = 78 µH T j = 100 C
V CEW Maximum Collector I CWoff = 48 A I B1 = 6.4 A 450 V
Emitter Voltage V BB = -5 V VCC = 50 V
Without Snubber L = 52 µH R BB = 0.39 Ω
T j = 125 o C
∗ Pulsed: Pulse duration = 300 µs, duty cycle 1.5 %
2/7
BUV298AV
Safe Operating Areas Thermal Impedance
Derating Curve Collector Emitter Voltage Versus
Base Emitter Resistance
Collector Emitter Saturation Voltage Base Emitter Saturation Voltage
3/7
BUV298AV
Reverse Biased SOA Forward Biased SOA
Reverse Biased AOA Forward Biased AOA
Switching Times Inductive Load Switching Times Inductive Load Versus
Temperature
4/7
BUV298AV
Dc Current Gain Turn-on Switching Test Circuit
(1) Fast electronics switch (2) Non-inductive load
Turn-on Switching Waveforms
Turn-off Switching Test Circuit Turn-off Switching Waveforms
(1) Fast electronic switch (2) Non-inductive load
(3) Fast recovery rectifier
5/7
BUV298AV
ISOTOP MECHANICAL DATA
mm inch
DIM.
MIN. TYP. MAX. MIN. TYP. MAX.
A 11.8 12.2 0.465 0.480
A1 8.9 9.1 0.350 0.358
B 7.8 8.2 0.307 0.322
C 0.75 0.85 0.029 0.033
C2 1.95 2.05 0.076 0.080
D 37.8 38.2 1.488 1.503
D1 31.5 31.7 1.240 1.248
E 25.15 25.5 0.990 1.003
E1 23.85 24.15 0.938 0.950
E2 24.8 0.976
G 14.9 15.1 0.586 0.594
G1 12.6 12.8 0.496 0.503
G2 3.5 4.3 0.137 1.169
F 4.1 4.3 0.161 0.169
F1 4.6 5 0.181 0.196
P 4 4.3 0.157 0.169
P1 4 4.4 0.157 0.173
S 30.1 30.3 1.185 1.193
P093A
6/7
BUV298AV
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences
of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is
granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specification mentioned in this publication are
subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products
are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics.
The ST logo is a trademark of STMicroelectronics
© 2001 STMicroelectronics – Printed in Italy – All Rights Reserved
STMicroelectronics GROUP OF COMPANIES
Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco -
Singapore - Spain - Sweden - Switzerland - United Kingdom - United States.
http://www.st.com
7/7
