RY
EO
TH
T Y
C I
PA
CA
G
N CITY
I
R CAPA
A
BEEARING
B
1
DEFENITION
• The term ‘Bearing cpacity of soil‘ is used to
indicate the maximum load per unit area which
the soil will resist safely without displacement
• By dividing the ultimate bearing power of soil
by a factor of safely,the bearing capacity of a
soil is obtained……….
2
Important…..
MAXIMUM SAFE BEARING CAPACITY OF SOIL ::-
It’s used to indicate the max.pressure that a soil can bear without
any risk of shear failure only , irrespective of any settlement that
may occur
ALLOWABLE BEARING PRESSURE ON SOIL::-
Used to indicate the max.pressure which can be exerted on a soil
while taking into account shear failure settlement and the ability of
structure to resist settlement.thus its value will depend on the
nature of ground and the type of building.
NET PRESSURE INTENCITY::-its used to indicate the excess pressure
or the diff. in the intencities of the gross pressure after the
construction of the structure and the original overburden pressure
3
BEARING CAPACITY FAILURE
a) General Shear Failure Most
common type of shear
failure; occurs in strong
soils and rocks
b) Local Shear Failure
Intermediate between
general and punching shear
failure
c) Punching Shear Failure
Occurs in very loose sands
weak clays
4
BEARING CAPACITY FAILURE
General shear failure
Local shear failure
Punching shear
failure
5
SOIL CONDITIONS AND
BEARING
CAPACITY FAILURE
6
LOAD DISPLACEMENT
CURVES (AFTER VESICʼ (1973))
a) General Shear Failure
b) Local Shear Failure
c) Punching Shear Failure
7
COMMENTS ON SHEAR FAILURE
Usually only necessary to analyze
general shear failure.
Local and punching shear failure can
usually be anticipated by settlement
analysis.
Failure in shallow foundations is
generally settlement failure; bearing
capacity failure must be analyzed,
but in practical terms is usually
secondary to settlement analysis.
8
DEVELOPMENT OF BEARING CAPACITY THEORY
Application of limit equilibrium methods
first done by Prandtl on the punching of
thick masses
of metal.
Prandtl's methods adapted by Terzaghi
to bearing capacity failure of shallow
foundations.
Vesicʼ and others improved on Terzaghi's
original
theory and added other factors for a
more complete analysis
9
ASSUMPTIONS FOR TERZAGHI'S
METHOD
Depth of foundation is less than or
equal to its width
No sliding occurs between foundation
and soil
(rough foundation)
Soil beneath foundation is
homogeneous semi infinite mass
Mohr-Coulomb model for soil
General shear failure mode is the
governing
mode (but not the only mode)
10
ASSUMPTIONS FOR TERZAGHI'S
METHOD
No soil consolidation occurs
Foundation is very rigid relative to the
soil.
Soil above bottom of foundation has no
shear
strength; is only a surcharge load against
the
overturning load.
Applied load is compressive and applied
vertically to the centroid of the
foundation
No applied moments present
11
TERZAGHI'S METHOD
Since soil cohesion can be difficult to
quantify, conservative values of c (cohesion)
should be used.
Frictional strength is more reliable and does
not need to be as conservative as cohesion.
Terzaghi's method is simple and familiar to
many geotechnical engineers; however, it
does not take into account many factors, nor
does it consider cases such as rectangular
foundations.
12
FAILURE GEOMETRY FOR TERZAGHI'S
METHOD
13
PRESUMPTIVE BEARING CAPACITY
Building codes of various organizations in
different countries gives the allowable
bearing capacity that can be used for
proportioning footings.
These presumptive bearing capacity values
based on experience with other structures
already built.
As presumptive values are based only on
visual classification of surface soils, they are
not reliable.
These values don't consider important
factors affecting the bearing capacity such
as the shape, width, depth of footing,
location of water table, strength and
compressibility of the soil. 14
Generally these values are conservative and
can be used for preliminary design or even
for final design of small unimportant
structure.
IS1904-1978 recommends that the safe
bearing capacity should be calculated on the
basis of the soil test data. But, in absence of
such data, the values of safe bearing
capacity can be taken equal to the
presumptive bearing capacity values.
It is further recommended that for non-
cohesive soils, the values should be reduced
by 50% if the water table is above or near
base of footing.
15
16
MEYERHOF’S ANALYSIS
Assumptions
Failure zones to extend above base level of
the footing.
The logarithmic spiral extends right up to
the ground surface.
Meyerhof (1951, 1963 ) proposed an
equation for ultimate bearing capacity of
strip footing which is similar in form to that
of Terzaghi but includes shape factors,
depth factors and inclination factors.
Meyerhof's equation is
17
VESIC'S BEARING CAPACITY THEORY
Vesic(1973) confirmed that the basic nature
of failure surfaces in soil as suggested by
Terzaghi as incorrect.
Developed formulas based on theoretical and
experimental findings.
Vesić retained Terzaghi’s basic format and
added additional factors, which produces
more accurate bearing capacity values.
Applies to a much broader range of loading
and geometry conditions.
18
The bearing capacity formula is re-written as
19
SKEMPTON’S ANALYSIS
Skempton (1951) based on his investigations
of footings on saturated clays observed that
the bearing capacity factor � C is a function
of ratio D/B in the case of strip footing and
square or circular footings, for Φ = 0
condition.
Bearing capacity factors in Terzaghi's
equation tends to increase with depth for a
cohesive soil.
20
21
FIELD TESTS: DIRECT DETERMINATION OF
BEARING CAPACITY OF SOIL
Plate Load Test
Vane Shear test
Dynamic cone penetration
Field-Density (approximation)
Field observation
Previous Knowledge
Field Sample Collection
22
PLATE LOAD TEST
Simplest and widely used field test- plate
load test
A square pit of sides equal to five times the width of
test plate is dug up to the required depth.
Test plates are iron plates of size 60cm square for
clayey soil 30cm square for sandy soil.
At the centre of the pit, a square hole of size equal to
the test plate is dug.The bottom of the test plate
should be along the proposed foundation level.
(b1/d1=b2/d2)
23
24
Seat the plate accurately over the
centre of pit and it should be in
contact with the soil over the
whole area
A loading post and hydraulic jack
is provided above the test
plate.Hydraulic jack support a
gravity loading platform. The
loading is done with sand
bags,concrete blocks.
Load is increased in regular
increments of 250kg or 1/5th of
ultimate bearingcapacity
whichever is less
25
Each loading increment is kept in postion until no
further measurable settlement occurs. Settlement of
the plate is measured by two sensitive dial guage of
sensitivity 0.02mm.
Plot a graph between settlement and load.
From the graph measure maximum load upto which
settlement is proportional
26
ultimate Bearing capacity of soil = Maximum
load/area of test plate
Safe bearing capacity
FACTOR OF SAFETY MAY BE 2 OR 3
27
METHODS FOR IMPROVING BEARING CAPACITY
OF SOIL
Increase the depth of foundation
By draining the soil
Water content in soil will decreases its bearing capacity
By draining sandy soil and gravel by gravity pipe drainage system-
improve bearing capacity
By compacting the soil
Reduces the open spaces between the individual particles
By grouting
Cement mortar can be injected under pressure into the subsoil to
seal off voids in between subsoil and foundation.
28
By confining the soil
Sheet piles are driven around the structure to form an enclosure
Which will prevent the movement of soil.
Chemical treatment
Chemical solution are injected under pressure into the soil
Forms a gel and keep soil particles together to form a compact
mass.
By grouting
Cement mortar can be injected under pressure into the subsoil to
seal off voids in between subsoil and foundation.
29
FIELD TESTS: CALCULATION BASED ON
ENGINEERING PROPERTIES
Shear tests: measuring shear strength of
soil
Triaxial test: measurement of shear strength
in all three dimensions
Consolidation test: expulsion of water under
static sustained load.
Settlement Analysis: analysis of load bearing
based on settlement of soil.
30
THANK YOU……
Harigovind s
Roll no :22
S1 s2
31
