TIBAGAN HIGH SCHOOL

Seventh Ave., Brgy. East Rembo 1216 City of Makati

DIAGNOSTIC TEST IN TECHNOLOGY AND LIVELIHOOD EDUCATION 7 and 8

NAME:_________________________________________________ SECTION:___________________

TEST I. REMEMBERING. DIRECTIONS: Choose the correct answers. Write the letters of your answers
in your answer sheet.
1. What type of resistor has a single value only?
A. film type C. rotary type
B. fixed type D. variable type
2. Which of the statement characterize a capacitor?
A. It discharge electron voltage.
B. It is made up of carbon dust or graphite paste, low wattage values.
C. It is metallic bodies for heat sink mounting, very high wattage ratings.
D. It is made up from conductive metal oxide paste, very low wattage values.
3. Which is the best resistor for volume and tuning receiver?
A. carbon resistor C. relay
B. film resistor D. transistor
4. What part doesn’t fit in the basic component of simple electrical circuit?
A. conducting wires C. load
B. diode D. source
5. Which of the following tools classified as a Cutting tool?
A. hammer C. side cutting pliers
B. multi tester D. screw drivers
6. How many ohms can resist of a single fixed type resistor?
A.1-10M Ω C.10M-100MΩ
B.1000-100MΩ D.100M-1BΩ
7. What is the color of representing 20% tolerance?
A. black C. no color
B. gold D. silver
8. What is the value of a resistor with a green-blue-black-silver color code?
A. 56 Ohms±10% C. 5.6K Ohms±10%
B. 560 Ohms±10% D. 56K Ohms±10%
10. What is the value of a resistor with a red-violet-brown-silver color code?
A. 27 Ohms±10% C. 2.7K Ohms±10%
B. 270 Ohms±10% D. 27K Ohms±10%
9. What is the value of a resistor with a yellow-yellow-yellow-gold color code?
A. 440 Ohms±5% C. 44K Ohms±5%
B. 4.4K Ohms±5% D. 440K Ohms±5%
11. What is the value of a resistor with a blue-black-orange-gold color code?
A.600 Ohms ± 5% C. 60K Ohms±5%
B.6K Ohms±5% D. 600K Ohms ±5%
12. What type of fixed resistors made from carbon dust and has a low wattage rating?
A. carbon resistor C. spin pulley
B. film resistor D. top cover
13. Which type of resistors has a characteristic to adjust and control some electronic operation?
A. film type C. rotary type
B. fixed type D. variable type
14. What classification of hand tools and equipment are represented by the multi tester, oscillator, and
signal generator?
A. driving tools C. measuring tools
B. gripping tools D. striking tools
15. What classification of hand tools state that it is used for Instruments for determining various quantities
such as temperature, mass, height, length, voltage and mechanical force?
A. driving tools C. measuring tools
B. gripping tools D. striking tools

TEST II. UNDERSTANDING. DIRECTIONS: Choose the correct answers. Write the letters of your
answers in your answer sheet.
16. Which is the best definition of Electronics?
A. It is a study of electronic circuit.
B. A technical skills for electronic servicing.
C. Comes from a two words electron and mechanics.
D. It is a branch of physics deals to study of behavior of electrons in the circuit.
17. What is function of Transistor in electronic circuit?
A. It permits as a storage of electricity.
B. It transfer with low resistance to high resistance.
C. An electronic component used to resist the flow of electrons
D. Used to amplify and switch electronic signals and electrical power.
18. Which of following statements is fact in ohm’s law?
A. Resistance measured in ohms, symbolized by the letter ”E”
B. Current is measured in amps, symbolized by the letter "Ω".
C. Explain the relationship of voltage, current and resistance.
D. Voltage is measured in volts, symbolized by the letters "I" or "V".
19. How will you use the multi-tester in troubleshooting activities?
A. It is used for more accurate and quality output.
B. It can be performed as a voltmeter, an ammeter and an ohmmeter.
C. It is used for electronic test that allows signal voltage to be viewed.
D. Typically used in simple electronics repair and design to stimulate a circuit under test.
20. Which of the following is more probable to use in making casing in electronics servicing?
A. electric drill because it’s a power tool
B. soldering iron because it’s a special tool
C. socket wrench set because a driving tool
D. A hammer and a screw driver because it designed for assembling and disassembling.
21. Which is more probable to use in measuring wave frequency?
A. Oscillator because it is a precision tool.
B. Multi tester because it is measuring tool.
C. Capacitor because it used for storing signal.
D. Signal generator because it is design for receiving frequency.
22. What does this mean a screw driver used for loosening and tightening screws?
A. A screw driver is cutting tool.
B. A screw driver is a driving tool.
C. A screw driver is a striking tool.
D. A screw driver is a gripping tool.
23. What is the difference between mensuration and calculation?
A. Mensuration is a process of calculation.
B. Calculation is a process of mensuration.
C. Mensuration is a procedure of computing, while calculation is a process of measuring.
D. Calculation is a procedure of computing, while mensuration is a process of measuring.
24. What is the function of Integrated Circuit in the electronic circuit?
A. Control the entire circuit operation.
B. Allows current flow in one direction only (left to right).
C. Conduct electricity and allow electricity to pass through.
D. An amplifier, oscillator, timer, microprocessor, or even computer memory.
25. What does this mean if the electrical circuit is closed?
A. Reduce the current flow.
B. Wires are not connected
C. Two terminals are grounded.
D. Allows current flow in the circuit.
26. Why is it important to use a personal protective equipment when you are in the workshop?
A. It avoid accident in the workplace.
B. It is comfortable for workers while in the workplace.
C. It provides safety and health precautions for workers.
‘
D. It is a standard procedure to always use a PPE properly in a particular task.
27. Which of the following diagram are the best in electrical installation servicing?
A. schematic diagram because it has an actual illustration
B. pictorial diagram because it has a complete electronic symbols
C. Pictorial diagram because it is more realistic than schematic diagram.
D. Schematic diagram because it has an electronic or electrical symbols needed for servicing.
28. What would happen if you used a worn out screw driver?
A. It gives another expenses.
B. It may cause damage or accident.
C. It gives a positive outcome for activities.
D. It may cause hard times in working progress.
29. What would be the result if a circuit has two 3V batteries in series, what is the voltage across the two
batteries?
A. 6 Volts C. 12 Volts
B. 9 Volts D. 15 Volts
30. Which of the following would be the best statement why Capacitor and resistor are same in what
aspect?
A. They have both fixed type.
A. They have the same value.
B. They have same function in electronic circuit.
D. They have both single value only in fixed type.

TEST III. APPLYING. DIRECTIONS: Choose the correct answers. Write the letters of your answers in
your answer sheet.
31. Which is the best function of a rotary type resistor?
A. It can discharge electrical voltages.
B. Best used for domestic radio receiver.
C. Used for volume and gain controls as well as a variety of other applications
D. It can store electric charge even the voltage source is already disconnected.
32. Which is the best statements deals to the function of diode?
A. It has a three connection.
B. It controls the behaviour of electron.
C. It is best used for tuning and radio receiver.
D. It is a device that allows electric current to flow in one direction only.
33. What would happen if you used the zener diode in your electronic circuit?
A. It rings when activated
B. It produces buzzing sound
C. It changes AC voltage from high to low or low to high.
D. The current flow is in reverse direction when above breakdown voltage.
34. Why is it important to use a personal protective equipment when you are in the workshop?
A. It avoid accident
B. It is comfortable for a worker while in workplace.
C. It provide safety and health precautions for the workers.
D. It is a standard procedure to always use a PPE properly in a particular task.
35. Which is the best definition of conducting component?
A flexible non-metallic conduit.
B. A wire through which current flow.
C. A cord that provides path for current flow
D. Used to cover electric wire, made in plastic rubber or asbestos.
36. What is the function of resistor in circuit?
A. Used to store electricity.
B. A semiconductor device that amplified electrons.
C. It affects to the behaviour of electrons flow into the circuit.
D. Its function is to resist or impede the electrons flow into the circuit.
37. What is better capacitor for tuning and radio receiver? Why?
A. Mica type it has a very low wattage rating.
B. Electrolytic type capacitor it has a high value.
C. Fixed capacitor because it has a single value only.
D. Variable capacitor because it is adjustable and gaining control capacitor.

TEST IV. ANALYZING. DIRECTIONS: Choose the correct answers. Write the letters of your answers in
your answer sheet.
38. Which of the following statements describe the function of a closed circuit?
A. There are two or more live wires.
B. There is no continuous current flow.
C. The flow of electric current is from the load to source back to load.
D. The flow of electric current is from the source to load back to source.
39. Which of the following statements are not fact about process of product development?
A. Analyze competitive product C. Identify product needs
B. Establish product specifications D. Product implementation
40. Which is the best statement among the purpose of the unique selling plan?
A. Examine the present and future needs.
B. Identify what motivates your customers.
C. Examine the existing goods and services.
D. Creating name, symbol or designs that identifies and differentiates products/ services.
41. Which is a not fact in the function of occupational health?
A. Protect workers from risk resulting from factors adverse to health.
B. Prevent workers from resignation due to health caused by poor working conditions.
C. Promote and maintain the highest degree of physical, mental and social well-being of workers.
D. Maintain the worker in an environment not suitable to his physiological and psychological capabilities.
42. How do you distinguish the circuit breaker?
A. It is a circuit that controls the amount of power supplied to electronic circuit.
B. It is an input receiver that detects input signal coming from forward and reverse motor.
C. It is a set of push button switch that set the operation required of the washing machine.
D. It is a processing circuit that accepts the input signal coming from sensor and program control.
43. Which of the following statement support the moral of the workers?
A. Occupational safety and health requirements may be reinforced in civil law and/or criminal law.
B. Safety Standards designed to ensure the safety of products, activities or processes and others.
C. Human welfare in terms of the production, distribution, and consumption of goods and services.
D. An employee should not have to risk injury at work, nor should associated with the work environment.
44. How does the short circuit occurred?
A. When the switch is open but there is no current flow in the circuit.
B. When the circuit is open but two or more wires contact with each other.
C. When the circuit is closed but two or more wires contact with each other.
D. When the switch is closed but two or more wires contact with each other.

TEST V. EVALUATING. DIRECTIONS: Choose the correct answers. Write the letters of your answers in
your answer sheet.
45. Occupational Safety and Health (OSH) is a cross-disciplinary area concerned with protecting the safety,
health and welfare of people engaged in work or employment. Employee A says it may also protect co-
workers, family members, employers, customers, suppliers nearby communities, and other members of the
public but Employee B says many governments realize that poor occupation and health conditions results
to cost to the State. Who do you think is right between Employee and Employee B?
A. Employee A only C. both Employee A and B
B. Employee B only D. neither Employee A nor B
46. How will you compare series and parallel circuit?
A. The current flow in series is one direction only while in parallel are two or more path.
B. The current flow in parallel is one direction only while in series are two or more path.
C. In parallel circuit, the lowest voltage will have brightest light opposite than series circuit.
D. In series circuit, the lowest voltage will have brightest light opposite than parallel circuit.
47. Electromotive force causes the electrons to move in a particular direction. Technician A says that it also
a term that describes the forces that oppose the flow of electron current in a conductor. But Technician B
says No! Only Resistance can oppose the flow of electron current in a conductor. Who do you think is right
between Technician A and Technician B?
A. Technician A only C. Both Technician A and B
B. Technician B only D. Neither Technician A nor B

TEST VI. CREATING. DIRECTIONS: Choose the correct answers. Write the letters of your answers in
your answer sheet.
48. The following statements are the procedure for safety in case of fire. How will you arrange them in a
sequence from step I to IV?
I. Assess the danger prior to doing anything.
II. If it is possible close the door to the fire area.
III. Call for assistance. Verbally call FIRE, FIRE, in a loud and clear voice.
IV. If it is safe to move assist anyone in the area of the fire away from danger.
A. I, IV, II, and III C. III, I, II, and IV
B. II, I, IV, and III D. IV, I, III, and II
49. How will you determine the exact measures of the voltage through convenience outlet in your home?
A. Check the kilo watt meter.
B. Get a screw drivers and dismantle the convenience outlet
C. Get a test lamp and connect it to the openings of the outlet.
D. Using a multi tester, set it to highest AC rate and connect the probes to the outlet openings.
50. What does it mean by “use a right tool, for a right job”?
A. Use a tool properly
B. Make a tool room for your tools.
C. Use a proper tool for specific job.
D. Tools should be in a good condition.

PREPARED BY: REVIEWED BY: APPROVED BY:

JAY RONNEL N. NAPIRI VIOLETA M. SORIANO ALIXANDER HABAN ESCOTE