Jenbacher gas engines

Technical Specification

JMS 620 GS-N.L

Natural gas 3.041kW el.

GE Jenbacher GmbH & Co OHG Tel. +43 5244 600-0 http://information.jenbacher.com

A-6200 Jenbach, Austria Fax +43 5244 63255 [email protected]

JMS 620 GS-N.L
Natural gas 3.041kW el.

CO-GEN Module data: Additional information:

Electrical output kW 3.041 Sound pressure level (engine, average value 1m) dB(A) 101
Recoverable thermal output (120 °C) el.
kW 3.020 Sound pressure level exhaust gas (1m, 30° off engin dB(A) 123
Energy input kW 7.076 Exhaust gas mass flow rate, wet kg/h 17.325
Fuel Consumption based on a LHV of Exhaust gas volume, wet Nm³/h 13.666
9,5 kWh/Nm³ Nm³/h 745 Max.admissible exhaust back pressure after engine mbar 60
Electrical efficiency % 43,0% Exhaust gas temperature at full load °C [8] 425
Thermal efficiency % 42,7% Combustion air mass flow rate kg/h 16.816
Total efficiency % 85,7% Combustion air volume Nm³/h 13.008
Heat to be dissipated (LT-Circuit) kW 188 Max. inlet cooling water temp. (intercooler) °C 40
Emission values: Max. pressure drop in front of intake-air filter mbar 10
NOx < 500 mg/Nm³ (5% O2) Return temperature °C 70
Forward temperature °C 90
Hot water flow rate m³/h 129,7

Engine data: Alternator:

Engine type J 620 GS-E01 Manufacturer AVK
Configuration V 60° Type DIG 140 k/4
No. of cylinders 20 Type rating kVA 4.000
Bore mm 190
Stroke mm 220
Piston displacement lit 124,75 Efficiency at p.f. = 1,0 % 97,5%
Nominal speed rpm 1.500 Efficiency at p.f. = 0,8 % 96,6%
Mean piston speed m/s 11 Ratings at p.f. = 1,0 kW 3.041
Mean effe. press. at stand. power and nom. spe bar 20,00 Ratings at p.f. = 0,8 kW 3.013
Compression ratio Epsilon 11,0 Frequency Hz 50
ISO standard fuel stop power ICFN kW 3119 Voltage kV 10,5
Spec. fuel consumption of engine kWh/kWh 2,27 Protection Class IP 23
Specific lube oil consumption g/kWh 0,30 Insulation class F
Weight dry kg 12.000 Speed rpm 1.500
Filling capacity lube oil lit 670 Mass kg 10.000
Based on methane number|Min. methane num MZ 94|80

Technical parameters:

Applicable standards: Based on DIN-ISO 3046

Based on VDE 0530 REM with specified tolerance
Standard conditions: Air pressure: 1000 mbar or 100 m above sea level
Air temperature: 25°C or 298 K
Relative Humidity: 30%

Engine output derating:

for plants installed at > 500m above see level and/or intake temperature > 30°C, the reduction of engine power is
determined for each project.

Gas quality: according to TA 1000-0300

Gas flow pressure: 80 - 200 mbar
(Lower gas pressures upon inquiry)
Prechamber gas pressure: 3,0-4,0 bar

Max. variation in gas pressure: ±10%

All data are based on engine full load at specified media temperatures and are subject to change.

The technical Instruction TA 1100-0110 "PARAMETER FOR GE Jenbacher GAS ENGINES" must be strictly observed.
>>> Scope of supply genset - JGS 620 GS-N.L

Basic engine equipment: Module equipment:

*Exhaust gas turbocharger, Intercooler *Base frame for gas engine,
*Motorized carburator for LEANOX control alternator and heat exchangers
*Electronic contactless high performance ignition system *Internal pole alternator with excitation alternator and
*Lubricating oil pump (gear driven) with automatic voltage regulator; p.f. 0,8 lagging to 1,0
*Lubricating oil filters in main circuit *Flexible coupling, bell housing
*Lubricating oil sump; Lubricating oil heat exchanger *Anti-vibration mounts
*Jacket water pump *Air filter
*Fuel-, lubricating oil and jacket water pipe work on engine *Automatic lube oil replenishing with level control
*Flywheel for alternator operation; Exhaust gas manifold *Wiring of components to module interface panel
*Viscous damper *Crankcase breather
*Knock sensors *Jacket water electric preheating

Engine accessories:
*Electric starter motor
*Electronic speed governor
*Electronic speed monitoring device including starting and Module control panel:
overspeed control *Totally enclosed , single door cubicle, wired to terminals and
*Transducers and switches for oil pressure, jacket water temp., ready to operate, protection IP 41
outside, jacket water pressure, charge pressure and mixture temperature IP 10 inside, according to VDE-
standards
*One thermocouple per cylinder Control equipment:
*Engine-Management-System dia.ne (Dialog Network)
Supplied loose: **Visualisation (industry PC-10'' color graphics display): Operation
data, Gas train according to DIN-DVGW consisting of: controller display,Exh. gas temp.,Generator electr.
connection,etc.
*Manual stop valve, fuel gas filter, two solenoid valves, **Central engine- and module control: Speed-, Power
output-, Leakage control device, gas pressure regulator LEANOX-Control and knock control, etc.
Prechamber Gas Train *Multi-transducer
Documentation: *Lockable operation mode selector switch
*Operating and maintenance manual Positions: "OFF", "MANUAL", "AUTOMATIC"
*Spare parts manual *Demand switch
*Drawings

Assembly, painting, testing in Jenbach/Austria

>>> Scope of supply module - JMS 620 GS-N.L

Identical to Genset except that heat recovery is included.

*jacket water heat exchanger mounted on module frame
*exhaust gas heat exchanger mounted as separate heat recovery module
*all heat exchangers with complete pipework
*Heat exchangers and all inherent auxiliaries

Scope of Supply & Design Subject to Local Regulations and product development
Genset

Main dimensions and weights (approximate value) Connections (at genset)

Length L mm 8.900 Jacket water inlet and outlet DN/PN 100/10
Width B mm 2.500 Exhaust gas outlet DN/PN 600/10
Height H mm 2.800 Fuel gas (at gas train) DN/PN 100/16
Weight empty kg 29.400 Intercooler water connection:
Weight filled kg 30.400 Low Temperature Circuit DN/PN 65/10

Module

Main dimensions and weights (approximate value) Connections (at module)

Length L mm 8.900 Hot water inlet and outlet DN/PN 100/10
Width B mm 2.500 Exhaust gas outlet DN/PN 600/10
Height H mm 2.800 Fuel gas (at gas train) DN/PN 100/16
Weight empty kg 30.000 Intercooler water connection:
Weight filled kg 31.000 Intercooler water-Inlet/Outlet 2nd stage DN/PN 65/10

Heat recovery module

Main dimensions and weights (approximate value) Connections (on heat recovery module)

Width B mm 1.962 Hot water inlet and outlet DN/PN 100/10

Height H mm 5.800 Exhaust gas outlet DN/PN 600/10
Length L mm 6.750 Condensate drain DN/PN 50/10
Drain line ½'' ½''

04
GE Jenbacher GmbH & Co OHG Tel. +43 5244 600-0 http://information.jenbacher.com .
Jul
20
06
A-6200 Jenbach, Austria Fax +43 5244 63255 [email protected]