Page 1 of 120

Order No. 198155TRFSAF

TEST REPORT
EN 60335-2-102 / EN 60335-2-6
Safety of household and similar electrical appliances
Part 2-102: Particular requirements for gas, oil and solid-fuel burning appliances
having electrical connections
Part 2-6: Particular requirements for stationary cooking ranges, hobs, ovens and
similar appliances
Reference number: 198155TRFSAF
E.U.T.: Built in hobs
Mod : 6822 (see page 5 for speaking code)

Applicant’s name : PLASFORM PLASTĐK VE METAL END.A.Ş.

Address : Organize Sanayi Bölgesi PK:31 Merzifon
AMASYA / TURKEY

Compiled by (+ signature): Güray UÇUREL

Approved by (+ signature): Mehmet KÜÇÜK
Date of issue: 2011-11-20
Testing Laboratory: CE TEKNĐK TEST BELG. MÜH. HĐZM. SAN. ve TĐC. LTD.
Address: Đkitelli Organize Sanayi Bölgesi Eskoop San. Sitesi. C-2 No:65
Đkitelli / ĐSTANBUL - TURKEY

Applied Standard EN 60335-2-102:2006+ A1:2010

EN 60335-2-6 2003 + A1:2005 + A2:2008 + A11:2010
EN 60335-1:2002 + A11:2004 + A12:2006 + A1:2004 + A2:2006+
A13:2008+ A14.2010
EN 62233:2008
Listed under Directive 2006/95/EC
Non-standard test method…………..: N/A

Test Results: See page 2

Test Report Form No: TAS_01_2008-04-09

TRF Originator: Nemko S.p.A.
The test report merely corresponds to the tested sample.
It is not permitted to copy extracts of these test result without the written permission of the testing laboratory.
This document is a test report to be included in the Technical Documentation File the manufacturer or his representative in the EU
shall prepare and maintain available to the national authorities to give them the possibility to evaluate conformity of the product to the
LVD 2006/95/EC

Accredited Testing Laboratory

 Page 2 of 120

Order No. 198155TRFSAF

Safety -- T E S T R E P O R T

2011-11-20
Test Report No. : 198155TRFSAF ______________________________________________________________________________________________

Date of issue

Test item description Built in hobs

Trade Mark ....................................... PLASFORM - VĐNOLA
Manufacturer .................................... PLASFORM PLASTĐK VE METAL END.A.Ş
Model/Type reference....................... 6822 (see page 5 for speaking code)
Ratings ............................................. 3500W 220-240 V~ 50 Hz class I

Test Results according to the

standards of page 1: Pass

General Comments
The CE marked component has been declared by its manufacturer in conformity with the applicable
national legislation and it is given the presumption to satisfy the standard listed in table 24.1.
It is responsibility of product manufacturer to verify conformity of the component with a.m. standard.
Certificates/CE conformity declarations/manufacturers declarations of listed components shall be
included in the TCF of the product.

According to the directive 2006/95/EC, certificates or CE conformity declarations of components with

asterisk of table 24.1 shall be included in the TCF.

Factories (Production Sites)

PLASFORM PLASTĐK VE METAL END.A.Ş.
Organize Sanayi Bölgesi PK:31 Merzifon
AMASYA / TURKEY

Accredited Testing Laboratory

 Page 3 of 120

Order No. 198155TRFSAF

Copy of marking plate:

Accredited Testing Laboratory

 Page 4 of 120

Report No. 198155TRFSAF

List of Attachments (including a total number of pages in each attachment):

st
Attachment 1: IEC 60335-2-102 :2004 (1 Edition) +A1:2008
Attachment 2: EUROPEAN GROUP DIFFERENCES AND NATIONAL DIFFERENCES (EN 60335-2-6
2003 + A1:2003 + A2: 2008 + A11:2010 )
Attachment 3: EUROPEAN GROUP DIFFERENCES AND NATIONAL DIFFERENCES (EN 60335-2-
102:2006 + A1:2009)
Attachment 4: Photo documentation

Summary of testing:

Tests performed (name of test and test clause): Testing location:

All relevant clauses.
CE TEKNĐK TEST BELG. MÜH. HĐZM.
Complete tests were performed on model: 6822 SAN. ve TĐC. LTD.
No additional tests were performed on the other models
Đkitelli Organize Sanayi Bölgesi Eskoop
Throughout this report a point is used as the decimal separator. San. Sitesi. C-2 No:65
Đkitelli / ĐSTANBUL – TURKEY
Note:
Equipment used for testing is recorded and saved into the
company archive as instruments 198155INS.xls.
This documentation will be made available on request.
Summary of compliance with National Differences:
- European group differences (see attachment 2) according to:
EN 60335-2-6 2003 + A1:2003 + A2: 2008 +A11:2010 used in conjunction with
EN 60335-1:2002 + A11:2004 + A1:2004 + A12:2006 + A2:2006 + A13:2008+A14.2010 and
EN 62233:2008(incl. Corr:2008)
- European group differences (see attachment 3) according to:
EN 60335-2-102:2006+ A1:2009

Accredited Testing Laboratory

 Page 5 of 120

Report No. 198155TRFSAF

Variants explanation code

General product information: The appliance is a built in hobs
The model is 6....-.. or 7....-.. and the ....... may assume the following values:
DOT Number or alphabet Meanings
1 6= 60x60 hobs
6 or 7
7= 70x60 hobs
2 0= glass front knob enamel grid
1= glass front knob cast grid
2= glass front knob enamel/cast grid
3= glass side knob enamel grid
0 or 1 or 2 or 3 or 4 or 4= glass side knob cast grid
5 or 6 or 7 or 8 or 9 5= glass side knob enamel/cast grid
6= inox front knob enamel grid
7= inox front knob cast grid
8= inox side knob enamel grid
9= inox side knob cast grid
3 and 4 40= 4 gas burner
41= 4 gas burner +1 hotplate
40 or 41 or 50 or 31 or
50= 5 gas burner
22
31= 3 gas burner + 1 hotplate
22= 2 gas burner + 2 hotplate
-
5 and 6 AL=aliminum frame
AL or W1 or W2 W1=2500kWwok gas burner
nothing W2=3800 kW wok gas burner
Nothinh=3500W
If the dots in 6...-.. or 7...-AL are 6822 the appliance has the following electrical ratings:
3500 W 220-230V~ 50 Hz Cl. I.

This appliance is a cooking appliance built in hobs designed and built for domestic use.
It is composed by 0 or 1 or 2 electric hobs and 2 or 3 or 4 gas cooking zone.
All of variants equipped with ignition module.
Different models changes for the dimension enclosure and for the functions. Model 6822 is the most complex
and the other models are the same as 6822 without some components.

Hotplate big :2000W

Hotplate small : 1000W

Accredited Testing Laboratory

 Page 6 of 120

Report No. 198155TRFSAF

Test item particulars:

Classification of installation and use : Buit in appliance. Unattended
Supply Connection: Power cord fitted with plug
Nature of supply ........................................... : ~
Pollution degree ............................................. : 3
Class of protection against electrical shock.... : Class I
Environmental rating ........................................ : –
Degree of protection against moisture ............ : IPX0
Type of cord attachment ................................. : Power cord fitted with plug
Operating conditions ........................................ : continuous
Overall size of the equipment (WxDxH) .......... : 540x490x30 mm
Mass of the equipment..................................... : 8.5 kg
Nominal capacity of container ......................... : –
Type of mounting ............................................ : –
- built-in ............................................................ : Yes
- floorstanding................................................... : No
- independent .................................................. : No
- to be fixed to a support ................................. : Yes
- hand-held ...................................................... : No
Switch .............................................................. : Yes
Thermostat ...................................................... : No
Temperature limiter .......................................... : No
Thermal cut-out ............................................... : No
Electronic circuit .............................................. : No
Programme controller ..................................... : No
Timer ............................................................... : No
Stationary appliance ......................................... : Yes
Portable appliance ........................................... : No
Appliance kept in the hand ............................... : No
Appliance continuously loaded by hand........... : No
Thermostat without an OFF position ............... : No

Accredited Testing Laboratory

 Page 7 of 120

Report No. 198155TRFSAF

Energy regulator without an OFF position ....... : No

Motor with capacitor in auxiliary winding.......... : No
More than one function ................................... : No
Alternative accessories provided .................... : No
Interlock between lid and main switch ............ : No
Water outlet ..................................................... : No
Automatic control in flexible cable or cord ....... : No
Power supply cord provided ............................ : Yes
Appliance inlet provided .................................. : No
Length of cord < 2m ......................................... : Yes
Connection to water supply mains .................. : No
Appliance for unattended use ......................... : Yes
Appliance intended to be immersed for No
cleaning ........................................................... :
Drain hole provided ......................................... : No
Provision for discharging steam ...................... : No
Provision for discharging overflowing water .... : No
Pressure relief device provided........................ : No
Detachable liquid container ............................. : No
Bare heating elements .................................... : Yes
Appliance for outdoor use ............................... : No
Connector incorporating a thermostat ............ : No
Possible test case verdicts:
- test case does not apply to the test object ................. : N (Not applicable)
- test object does meet the requirement ....................... : P (Pass)
- test object does not meet the requirement ................. : F (Fail)
Testing:
Date of receipt of test item ............................................ : 05-10-2011
Date(s) of performance of tests .................................... : 30-10-2011 to 20-11-2011

Accredited Testing Laboratory

 Page 8 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

5 GENERAL CONDITIONS FOR THE TESTS -

Tests performed according to cl. 5, e.g. nature of P
supply, sequence of testing, etc.
5.3 Addition: for pyrolitic self-cleaning ovens, the tests of N
22.108 to 22.111 are carried out before the tests of
Clause 19 (IEC 60335-2-6 : 2002)
5.4 Addition: appliances that also use gas are supplied N
with gas at the appropriate rated pressure. Vessels
having a diameter of approximately 220mm are filled
with 2 l of water, covered with a lid and placed on the
hob burners. The controls are adjusted so that the
water simmers, water being added when necessary to
maintain the level (IEC 60335-2-6 : 2002)
5.101 Class III temperature-sensing probes are only N
subjected to the tests of Clause 19 (IEC 60335-2-6 :
2002)

6 CLASSIFICATION -
6.1 Protection against electric shock: Class I P
Class I, II, III (IEC 60335-2-6 : 2002):
6.2 Protection against harmful ingress of water P

7 MARKING AND INSTRUCTIONS -

7.1 Rated voltage or voltage range (V).......................... : 220-240 ~ P
Nature of supply ....................................................... : ~ P
Rated frequency (Hz) ............................................... : 50 P
Rated power input (W) ............................................. : 3500 P
Rated current (A) .................................................... : N
For induction hob elements and induction wok N
elements(IEC 60335-2-6 : 2002)
total rated power input or rated current
Single-phase appliances: 230V covered P
Multi-phase appliance: 400V covered: N

Accredited Testing Laboratory

 Page 9 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

Manufacturer's or responsible vendor's name, PLASFORM - VĐNOLA P

trademark or identification mark .............................. :
Model or type reference ........................................... : 6822 (see page 5 for speaking P
code)
Symbol 5172 of IEC 60417, for Class II appliances N
IP number, other than IPX0 ..................................... : N
Symbol IEC 60417-5036, for the enclosure of N
electrically-operated water valves in external hose-
sets for connection of an appliance to the water mains
Marking of the rated current of the fuse other than N
D-type fuse for cooking ranges incorporate a socket-
outlet. (IEC 60335-2-6 : 2002)
Marking of the rated current of the fuse other than N
D-type fuse (IEC 60335-2-6 : 2002)
7.2 Warning for stationary appliances for multiple supply N
Warning placed in vicinity of terminal cover N
7.3 Range of rated values marked with the lower and Voltage P
upper limits separated by a hyphen
Different rated values marked with the values Frequency P
separated by an oblique stroke
7.4 Appliances adjustable for different rated voltages, the N
voltage setting is clearly discernible
7.5 Appliances with more than one rated voltage or one or N
more rated voltage ranges, marked with rated input or
rated current for each rated voltage or range, unless
the power input is related to the arithmetic mean value P
of the rated voltage range
Relation between marking for upper and lower limits of N
rated power input or rated current and voltage is clear
7.6 Correct symbols used P
Symbol IEC 60417-5010: ON/OFF (push-push) (IEC N
60335-2-6 : 2002
7.7 Connection diagram fixed to appliances to be N
connected to more than two supply conductors and
appliances for multiple supply

Accredited Testing Laboratory

 Page 10 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

7.8 Except for type Z attachment, terminals for connection to the supply mains indicated as -
follows:
- marking of terminals exclusively for the neutral P
conductor (N)
- marking of protective earthing terminals (symbol P
5019 of IEC 60417)
- marking not placed on removable parts P
7.9 Marking or placing of switches which may cause a P
hazard
7.10 Indications of switches on stationary appliances and P
controls on all appliances by use of figures, letters or
other visual means ................................................... :
The figure 0 indicates only OFF position, unless no N
confusion with the OFF position
The figure 0 indicates OFF position and figure I N
indicates ON position of touch controls for hobs or
(IEC 60335-2-6:2002)
for each hob element (IEC 60335-2-6:2002) P
7.11 Indication for direction of adjustment of controls P
7.12 Instructions for safe use provided P
Instructions shall include the following: (IEC 60335-2-6:2002)
Warning: If the surface is cracked, switch off the N
appliance to avoid the possibility of electric shock, for
hob surfaces of glass-ceramic or similar material
which protect live parts
During use the appliances becomes hot. Care N
should be taken to avoid touching heating elements
inside the oven, for cooking ranges and ovens
Instructions for ovens: (IEC 60335-2-6:2002) -
Warning: Accessible parts may become hot during N
use. Young children should be kept away.
Instructions for ovens having doors with glass panels: (IEC 60335-2-6:2002) -
Do not use harsh abrasive cleaners or sharp metal N
scrapers to clean the oven door glass since they can
scratch the surface, which may result in shattering of
the glass.

Accredited Testing Laboratory

 Page 11 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

If during the test of Clause 11, the temperature rise N

at the centre of the internal bottom surface of a
storage drawer exceeds that specified for handles
held for short periods in normal use, the instruction
shall state that these surfaces can get hot.
Instructions for pyrolytic self-cleaning ovens shall: (IEC 60335-2-6:2002) -
- state that excess spillage must be remove before N
cleaning
- specify which utensils can be left in the oven during N
cleaning
Instructions shall state for cleaning used to set the controls to a position higher than -
for normal cooking purposes: (IEC 60335-2-6:2002)
- that under such conditions the surfaces may be get N
hotter than usual
- children should be kept away N
Instructions for ovens incorporating a fan with a guard that can removed for cleaning -
shall state that: (IEC 60335-2-6:2002)
- the oven must be switched off before removing the N
guard and
- after cleaning, the guard must be replaced in N
accordance with instructions
Instructions for ovens provided with a facility to use a temperature-probe shall include -
the following: (IEC 60335-2-6:2002)
-Only use the temperature probe recommended for N
this oven
Instructions for cooking ranges, hobs and oven (IEC 60335-2-6:2002) -
-shall state a steam cleaner is not be used P
Instructions for induction hobs shall state the following: (IEC 60335-2-6:2002) -
-Metallic objects such as knives, forks, spoons and N
lids should not be placed on the hob surface since
they can get hot
Instructions for hobs incorporating a lid shall state (IEC 60335-2-6:2002) -
-Any spillage should be removed from the lid before N
opening. They also state than that
- Hob surface should be allowed to cool before N
closing the lid
Instructions for hobs incorporating halogen lamps N
shall warn the user not to stare at the hob elements
(IEC 60335-2-6:2002)
Instructions for hob incorporating a pan detector shall include the following (IEC -
60335-2-6:2002)

Accredited Testing Laboratory

 Page 12 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

-After use, switch off the hob element by its control N

and do not rely on the pan detector
Instructions for appliances incorporating a lamp for illumination, and does not -
incorporate a switch providing full disconnection under overvoltage category shall
state the following: (IEC 60335-2-6:2002)
-Warning - Ensure that the appliance is switched off N
before replacing the lamp to avoid the possibility of
electric shock .
The instructions for hobs shall state that the P
appliance is not intended to be operated by means of
external timer or separated remote-control system
(IEC 60335-2-6:2002)
The instructions for hobs incorporating an induction N
wok element shall contain a list of vessels that can
be used, unless the manufacturer provides a wok
with the appliance (IEC 60335-2-6:2002)
The instructions for ovens that have shelves shall N
include details indicating the correct installation of
the shelves (IEC 60335-2-6:2002)
7.12.1 Sufficient details for installation supplied P
Instructions concerning cooking ranges placed on N
the floor. (60335-2-6)
maximum rated pressure for appliance intended to N
be connected to the water supply. (60335-2-6)
7.12.2 Stationary appliances not fitted with means for P
disconnection from the supply mains having a contact
separation in all poles that provide full disconnection
under overvoltage category III, the instructions state
that means for disconnection must be incorporated in
the fixed wiring in accordance with the wiring rules
7.12.3 Insulation of the fixed wiring in contact with parts N
exceeding 50 K during clause 11; instructions stating
that the fixed wiring must be protected
Instructions for cooking range does not have a N
supply cord shall state the type of cord to be used,
taking into account the temperature of the rear
surface of the appliance (IEC 60335-2-6:2002)
7.12.4 Instructions for built-in appliances:
- dimensions of space P
- dimensions and position of supporting means P
- distances between parts and surrounding structure P

Accredited Testing Laboratory

 Page 13 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

- dimensions of ventilation openings and arrangement N

- connection to supply mains and interconnection of N
separate components
- allow disconnection of the appliance after installation, N
by accessible plug or a switch in the fixed wiring,
unless
a switch complying with 24.3 N
Instructions for built-in appliances having a separate N
control panels shall state the control panel is only to
be connected to heating units specified in order to
avoid a possible hazard (IEC 60335-2-6:2002)
7.12.5 Replacement cord instructions, type X attachment with N
a specially prepared cord
Replacement cord instructions, type Y attachment P
Replacement cord instructions, type Z attachment N
7.12.6 Caution in the instructions for heating appliances with N
a non-self-resetting thermal cut-out
7.12.7 Instructions for fixed appliances stating how the N
appliance is to be fixed
7.12.8 Instructions for appliances connected to the water mains: -
- max. inlet water pressure (Pa) .............................. : N
- min. inlet water pressure, if necessary (Pa) .......... : N
Instructions concerning new and old hose-sets for N
appliances connected to the water mains by
detachable hose-sets
7.13 Instructions and other texts in an official language P
7.14 Marking clearly legible and durable P
7.15 Marking on a main part P
Marking clearly discernible from the outside, if N
necessary after removal of a cover
For portable appliances, cover can be removed or N
opened without a tool
For stationary appliances, name, trademark or N
identification mark and model or type reference visible
after installation

Accredited Testing Laboratory

 Page 14 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

For fixed appliances, name, trademark or identification N

mark and model or type reference visible after
installation according to the instructions
Or included in the instruction of use (IEC 60335-2- N
6:2002)
Or on an additional label fixed near the appliance N
after installation (IEC 60335-2-6:2002)
Indications for switches and controls placed on or near P
the components. Marking not on parts which can be
positioned or repositioned in such a way that the
marking is misleading
Marking for rated current of the fuse protecting a N
socket-outlet placed on or near the socket-outlet
(IEC 60335-2-6:2002)
7.16 Marking of a possible replaceable thermal link or fuse N
link clearly visible with regard to replacing the link
7.101 Marking of the maximum water level, which shall be N
visible during filling, for steam generators intended to
filled manually (IEC 60335-2-6:2002)
7.102 Appropriate marking the cooking zone of hob P
surfaces unless (IEC 60335-2-6:2002)
7.103 For cooking ranges that are normally placed on the N
floor and that have horizontally hinged oven doors
with a hinge height of less than 430mm from the
floor, if a stabilizing means is necessary in order to
comply with the test of 20.102, then: (IEC 60335-2-
6:2002)
-The stabilizing means shall be marked, in lettering N
at least 3mm high, with the substance of the
following warning:
WARNING: in order to prevent tipping of the
appliance, this stabilizing means must be installed.
Refer to the instructions for installation.
-The appliance shall be marked, in lettering at least N
3mm high, at the point of supply entry and at least
one other point to draw the attention of the user to
the need to stabilize the appliance.
it is obvious (IEC 60335-2-6:2002) N
8 PROTECTION AGAINST ACCESS TO LIVE PARTS -
8.1 Adequate protection against accidental contact with P
live parts

Accredited Testing Laboratory

 Page 15 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

8.1.1 Requirement applies for all positions, detachable parts P

removed
Insertion or removal of lamps, protection against N
contact with live parts of the lamp cap
Use of test probe B of IEC 61032: no contact with live P
parts
8.1.2 Use of test probe 13 of IEC 61032 through openings N
in class 0 appliances and class II appliances/
constructions: no contact with live parts
Test probe 13 also applied through openings in N
earthed metal enclosures having a non-conductive
coating: no contact with live parts
Test probe 12 of IEC 61032 also applied to parts P
liable to be touched accidentally in normal use by a
fork or similar pointed object: no contact with live
parts (IEC 60335-2-6:2002)
8.1.3 For appliances other than class II, use of test probe 41 N
of IEC 61032: no contact with live parts of visible
glowing heating elements
Test probe 41: no contact with live parts of visible N
glowing heating elements situated at the top of the
oven or grilling compartment. (IEC 60335-2-6:2002)
8.1.4 Accessible part not considered live if: N
- safety extra-low a.c. voltage: peak value not N
exceeding 42.4 V
- safety extra-low d.c. voltage: not exceeding 42.4 V N
- or separated from live parts by protective impedance N
If protective impedance: d.c. current not exceeding N
2 mA, and
a.c. peak value not exceeding 0.7 mA N
- for peak values over 42.4 V up to and including N
450 V, capacitance not exceeding 0,1 µF
- for peak values over 450 V up to and including N
15 kV, discharge not exceeding 45 µC
- for peak values over 15kV, the energy in the N
discharge not exceeding 350 mJ
8.1.5 Live parts protected at least by basic insulation before installation or assembly: -

Accredited Testing Laboratory

 Page 16 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

- built-in appliances P
- fixed appliances P
- appliances delivered in separate units N
8.2 Class II appliances and constructions constructed so N
that there is adequate protection against accidental
contact with basic insulation and metal parts
separated from live parts by basic insulation only
Only possible to touch parts separated from live parts N
by double or reinforced insulation

10 POWER INPUT AND CURRENT

10.1 Power input at normal operating temperature, rated (see appended table) P
voltage and normal operation not deviating from rated
power input by more than shown in table 1
Induction hob elements and induction wok elements: N
power input measured separately, tolerances for
motor-appliances apply. (IEC 60335-2-6:2002)
Socket-outlet are not loaded during the test N
(IEC 60335-2-6:2002)
10.2 Current at normal operating temperature, rated P
voltage and normal operation not deviating from rated
current by more than shown in table 2
Induction hob elements and induction wok elements: N
current measured separately, tolerances for
motor-appliances apply. (IEC 60335-2-6:2002)
Socket-outlet are not loaded during the test N
(IEC 60335-2-6:2002)

11 HEATING
11.1 No excessive temperatures in normal use P
For cooking ranges and ovens, compliance is also P
checked by the test of 11.101 (IEC 60335-2-6:2002)
11.2 Placing and mounting of appliance as described -
- built-in (IEC 60335-2-6:2002) P
- against a wall (IEC 60335-2-6:2002) N
- on the floor (IEC 60335-2-6:2002) N

Accredited Testing Laboratory

 Page 17 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

- fixed to the wall (IEC 60335-2-6:2002) N

- with or without the lid covering the hob surface N
(IEC 60335-2-6:2002)
- temperature sensing probes: any position likely to N
occur during normal use. (IEC 60335-2-6:2002)
- pyrolytic self-cleaning ovens: temperature sensing N
probe in position unless other instructions
(IEC 60335-2-6:2002)
Detachable parts that are intended to be used to N
reduce the temperature of controls panels are
removed(IEC 60335-2-6:2002)
11.3 Temperature rises, other than of windings, determined P
by thermocouples
Temperature rises of windings determined by N
resistance method, unless
the windings makes it difficult to make the necessary N
connections
11.4 Heating appliances operated under normal operation 1.15x3500Wx(240/230)² = P
at 1.15 times rated power input .............................. : 4383W (247V)
Induction hob elements and induction wok elements N
supplied separately and operated as for motor
operated appliances (IEC 60335-2-6:2002)
Cooking ranges operated under normal operation at P
1.15 times rated power input: (IEC 60335-2-6:2002)
11.5 Motor-operated appliances operated under normal N
operation at most unfavourable voltage between 0.94
and 1.06 times rated voltage ................................... :
11.6 Combined appliances operated under normal N
operation at most unfavourable voltage between 0.94
and 1.06 times rated voltage ................................... :
11.7 Appliance operated for the duration specified in 11.7.101 to 11.7.106 P
(IEC 60335-2-6:2002)
11.7.101 Induction hob elements and induction wok elements, 60 minutes P
other hob elements :
11.7.102 Ovens : N
Steam ovens operated in each mode of operation N
Lamps in ovens are not manually switched on N
11.7.103 Grills N
11.7.104 Griddles N

Accredited Testing Laboratory

 Page 18 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

11.7.105 Warming drawers and similar compartments : N

11.7.106 Cooking ranges : N
11.7.107 Appliance incorporates a socket–outlet with a N
appropriate plug complying with IEC60083
11.8 Temperature rises not exceeding values in table 3 (see appended tables) P
Temperatures rises of the floor and floor of the test P
corner, wooden cabinets and rectangular box not
exceeding specified values (IEC 60335-2-6:2002)
Sealing compound does not flow out P
Protective devices do not operate, except N
components in protective electronic circuits tested for N
the number of cycles specified in 24.1.4
11.101 Cooking ranges and ovens placed as described N
(IEC 60335-2-6:2002)
Appliance operated under normal operation at rated N
voltage
The appliance operated in specified conditions N
The appliance operated 60 min or N
until steady conditions are established N
Temperature rise of surfaces not exceed the values (see appended tables) N
specified in Table 102 (IEC 60335-2-6:2002)

13 LEAKAGE CURRENT AND ELECTRIC STRENGTH AT OPERATING

TEMPERATURE
13.1 Leakage current not excessive and electric strength P
adequate
Heating appliances operated at 1.15 times rated 1.15x3500Wx(240/230)² = P
power input ............................................................... : 4383W (247V)
Motor-operated appliances and combined appliances N
supplied at 1.06 times rated voltage ........................ :
Protective impedance and radio interference filters N
disconnected before carrying out the tests
If a grill is incorporated in the oven, either the oven N
or the grill is operated, whichever is more
unfavourable. (IEC 60335-2-6:2002)

Accredited Testing Laboratory

 Page 19 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

For hobs, the tests are carried out with a vessel filled P
as specified in 3.1.9.101 placed on each cooking
zone (IEC 60335-2-6:2002)
Induction hob elements and induction wok elements N
are tested as specified for motor-operated
appliances (IEC 60335-2-6:2002)
13.2 Leakage current measured by means of the circuit P
described in figure 4 of IEC 60990
Leakage current measurements (see appended table) P
13.3 The appliance is disconnected from the supply P
Electric strength tests according to table 4 (see appended table) P
No breakdown during the tests P

14 TRANSIENT OVERVOLTAGES -
Appliances withstand the transient overvoltages to N
which they may be subjected
Clearances having a value less than specified in table N
16 subjected to an impulse voltage test, the test
voltage specified in table 6
No flashover during the test, unless of functional N
insulation
In case of flashover of functional insulation, the N
appliance complies with clause 19 with the clearance
short circuited

15 MOISTURE RESISTANCE -
15.1 Enclosure provides the degree of moisture protection IPX0 N
according to classification of the appliance
Compliance checked as specified in 15.1.1, taking into N
account 15.1.2, followed by the electric strength test of
16.3
No trace of water on insulation which can result in a N
reduction of clearances and creepage distances below
values specified in clause 29
15.1.1 Appliances, other than IPX0, subjected to tests as N
specified in IEC 60529 ............................................. :

Accredited Testing Laboratory

 Page 20 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

Water valves in external hoses for connection of an N

appliance to the water mains tested as specified for
IPX7 appliances
15.1.2 Hand-held appliance turned continuously through the N
most unfavourable positions during the test
Built-in appliances installed according to the N
instructions
Appliances placed or used on the floor or table placed N
on a horizontal unperforated support
Appliances normally fixed to a wall and appliances N
with pins for insertion into socket-outlets are mounted
on a wooden board
For IPX3 appliances, the base of wall mounted N
appliances is placed at the same level as the pivot
axis of the oscillating tube
For IPX4 appliances, the horizontal centre line of the N
appliance is aligned with the pivot axis of the
oscillating tube
However, for appliances normally used on the floor or N
table, the movement is limited to two times 90° for a
period of 5 min, the support being placed at the level
of the pivot axis of the oscillating tube
Appliances normally fixed to a ceiling are mounted N
underneath a horizontal unperforated support, the
pivot axis of the oscillating tube located at the level of
the underside of the support
For IPX4 appliances, the movement of the tube is N
limited to two times 90° from the vertical for a period of
5 min
Wall-mounted appliances, take into account the N
distance to the floor stated in the instructions
Appliances with type X attachment fitted with a flexible N
cord as described
Detachable parts tested as specified N
15.2 Spillage of liquid does not affect the electrical P
insulation

Accredited Testing Laboratory

 Page 21 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

Appliances incorporating an appliance inlet tested with N

or without an connector, whichever is most
unfavourable
Detachable parts removed N
Overfilling test with additional amount of water, over a P
period of 1 min, quantity (l) :
Cooking ranges and hobs subjected to the overfilling P
test into the vessel with additional saline solution,
over a period of 15 s (l) .......................................... :
(IEC 60335-2-6:2002)
For hob elements incorporating a switch or a thermal N
control: overfilling test with saline solution(l):
(IEC 60335-2-6:2002) ............................................ :
If controls are mounted below the hob surface: P
overfilling test with saline solution, over a period of
15 s (l) .................................................................... :
(IEC 60335-2-6:2002)
If controls are mounted in the hob surface: overfilling N
test with saline solution, over them (l) .................... :
(IEC 60335-2-6:2002)
For hob having ventilating openings in the hob N
surface: overfilling test with saline solution (l) ........ :
(IEC 60335-2-6:2002)
For ovens and grills: overfilling test with saline N
solution (l) .............................................................. :
(IEC 60335-2-6:2002)
For appliances having a drip tray or similar N
receptacle: overfilling test with saline solution (l) ... :
(IEC 60335-2-6:2002)
For hobs having a lid: overfilling test with saline N
solution (l) .............................................................. :
(IEC 60335-2-6:2002)
Test repeated: overfilling test with saline solution , N
over a period of 15 s (l) .......................................... :
(IEC 60335-2-6:2002)
Steam generators intended to be connected to the N
water mains supplied at rated water pressure
(IEC 60335-2-6:2002)
Water allowed to flow for 1 min after the first N
evidence of overflow, unless (IEC 60335-2-6:2002)
the inflow stops automatically (IEC 60335-2-6:2002) N

The appliance withstands the electric strength test of N

16.3

Accredited Testing Laboratory

 Page 22 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

No trace of water on insulation that can result in a N

reduction of clearances and creepage distances below
values specified in clause 29
15.3 Appliances proof against humid conditions P

Humidity test for 48 h in a humidity cabinet P

The appliance withstands the tests of clause 16 P

15.101 Temperature-sensing probes shall be constructed so N
that their insulation is not affected by water
(IEC 60335-2-6:2002)
After the test, the probe withstand the leakage N
current test of 16.2 (IEC 60335-2-6:2002)

Accredited Testing Laboratory

 Page 23 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

16 LEAKAGE CURRENT AND ELECTRIC STRENGTH -

16.1 Leakage current not excessive and electric strength P
adequate
Protective impedance disconnected from live parts P
before carrying out the tests
Induction hob elements and induction wok elements: N
tested as motor-operated appliances (60335-2-6)
16.2 Single-phase appliances: test voltage 1.06 times rated P
voltage ...................................................................... :
Three-phase appliances: test voltage 1.06 times rated N
voltage divided by √3 ............................................... :
Leakage current measurements (see appended table) P
16.3 Electric strength tests according to table 7 (see appended table) P
No breakdown during the tests P

17 OVERLOAD PROTECTION OF TRANSFORMERS AND ASSOCIATED CIRCUITS

No excessive temperatures in transformer or N
associated circuits in event of short-circuits likely to
occur in normal use
Appliance supplied with 1.06 or 0.94 times rated N
voltage and the most unfavourable short-circuit or
overload likely to occur in normal use applied......... :
Temperature rise of insulation of the conductors of N
safety extra-low voltage circuits not exceeding the
relevant value specified in table 3 by more than 15 K
Temperature of the winding not exceeding the value N
specified in table 8,
however limits do not apply to fail-safe transformers N
complying with sub-clause 15.5 of IEC 61558-1

Accredited Testing Laboratory

 Page 24 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

19 ABNORMAL OPERATION -
19.1 The risk of fire or mechanical damage under P
abnormal or careless operation obviated
Electronic circuits so designed and applied that a N
fault will not render the appliance unsafe
For induction hobs compliance is also checked by N
the test 19.101and 19.102 (19.4 not applicable)
(IEC 60335-2-6:2002)
19.101 is not applicable to induction wok elements N
(IEC 60335-2-6:2002)
Temperature-sensing probes placed in the oven in N
any position likely to occur during normal use that
they are connected to control the oven temperature
(IEC 60335-2-6:2002)
19.2 Test of appliance with heating elements with 0.85x3500Wx(220/230)² = P
restricted heat dissipation; test voltage (V): power 2722W (195V)
input of 0.85 times rated power input
Hob elements are operated without a vessel, pan P
detectors being rendered inoperative.
Oven doors are open or closed, whichever is more
unfavourable.
Hob lids are closed unless the hob elements are
interlocked with the lid or an indicator lamp shows
that a hob element is switched on. (IEC 60335-2-
6:2002)
For appliances incorporating more than one heating P
unit, the test is only carried with the heating unit
resulting in the most unfavourable conditions, its
control adjusted to the highest setting.
For appliance incorporate an oven without an
indicator lamp to show that the oven is switched on,
the oven is operated, its control adjusted to the
highest setting. (IEC 60335-2-6:2002)
For induction hob element or induction wok element N
with a metallic lid: a force of 30N is applied to the
closed lid in the most unfavourable place by means
of test probe B of IEC 61032. (IEC 60335-2-6:2002)
Pyrolytic self-cleaning ovens are also operated N
under cleaning conditions, motors which operate
during cleaning being switched off or disconnect in
turn. (IEC 60335-2-6:2002)

Accredited Testing Laboratory

 Page 25 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

Induction hob elements and induction wok elements N

are operated under the conditions of clause 11 but
with empty vessels, the controls being adjusted to
the highest setting. (IEC 60335-2-6:2002)
Steam ovens are operated without water (IEC N
60335-2-6:2002)
Doors of separate grill compartments incorporate a N
cooking range are open or closed, which is the
most unfavourable. (IEC 60335-2-6:2002)
19.3 Test of 19.2 repeated; test voltage (V): power input of 1.24x(240/230)²x3500W = P
1.24 times rated power input .................................... 4726W (255V)
19.4 Test conditions as in cl. 11, any control limiting the P
temperature during tests of cl. 11 short-circuited
19.5 Test of 19.4 repeated on Class 0I and I appliances N
with tubular sheathed or embedded heating
elements. No short-circuiting, but one end of the
element connected to the elements sheath
The test repeated with reversed polarity and the other N
end of the heating element connected to the sheath
The test is not carried out on appliances intended to N
be permanently connected to fixed wiring and on
appliances where an all-pole disconnection occurs
during the test of 19.4
19.6 Appliances with PTC heating elements tested at N
rated voltage, establishing steady conditions
The working voltage of the PTC heating element is N
increased by 5% and the appliance is operated until
steady conditions are re-established. The voltage is
then increased in similar steps until 1.5 times working
voltage or until the PTC heating element ruptures
19.7 Stalling test by locking the rotor if the locked rotor N
torque is smaller than the full load torque or locking
moving parts of other appliances
Locked rotor, motor capacitors open-circuited or N
short-circuited, if required
Locked rotor, capacitors open-circuited one at a time N
Test repeated with capacitors short-circuited one at a N
time, if required

Accredited Testing Laboratory

 Page 26 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

Appliances with timer or programmer supplied with N

rated voltage for each of the tests, for a period equal
to the maximum period allowed
Other appliances supplied with rated voltage for a N
period as specified
Winding temperatures not exceeding values N
specified in table 8
19.8 Three-phase motors operated at rated voltage with N
one phase disconnected
19.10 Series motor operated at 1.3 times rated voltage for N
1 min .........................................................................:
During the test, parts not being ejected from the N
appliance
19.11 Electronic circuits, compliance checked by evaluation N
of the fault conditions specified in 19.11.2 for all
circuits or parts of circuits, unless they comply with
the conditions specified in 19.11.1
Appliances incorporating a protective electronic N
circuit subjected to the tests of 19.11.3 and 19.11.4
Appliances having a switch with an off position N
obtained by electronic disconnection, or a switch
placing the appliance in a stand-by mode, subjected
to the tests of 19.11.4
Appliances incorporating an electronic circuit that N
relies upon a programmable component to function
correctly, subjected to the test of 19.11.4.8
19.11.1 Before applying the fault conditions a) to f) in 19.11.2, it is checked if circuits or parts of -
circuit meet both of the following conditions:
- the electronic circuit is a low-power circuit, that is, N
the maximum power at low-power points does not
exceed 15 W according to the tests specified
- the protection against electric shock, fire hazard, N
mechanical hazard or dangerous malfunction in other
parts of the appliance does not rely on the correct
functioning of the electronic circuit
19.11.2 Fault conditions applied one at a time, the appliance operated under conditions -
specified in cl. 11, but supplied at rated voltage, the duration of the tests as specified:

Accredited Testing Laboratory

 Page 27 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

a) short circuit of functional insulation if clearances or N

creepage distances are less than the values
specified in 29
b) open circuit at the terminals of any component N
c) short circuit of capacitors, unless they comply with N
IEC 60384-14
d) short circuit of any two terminals of an electronic N
component, other than integrated circuits. This fault
condition is not applied between the two circuits of an
optocoupler
e) failure of triacs in the diode mode N
f) failure of an integrated circuit N
g) failure of an electronic power switching device N
During simulation it shall not possible to switch of N
any energized hob element (IEC 60335-2-6:2002)
The hob elements shall not become energized N
(IEC 60335-2-6:2002)
19.11.3 If the appliance incorporates a protective electronic N
circuit which operates to ensure compliance with
clause 19, the relevant test is repeated with a single
fault simulated, as indicated in a) to g) of 19.11.2
During and after each test the following is checked: -
- the temperature rise of the windings do not exceed N
the values specified in table 8
- the appliance complies with the conditions specified N
in 19.13
- any current flowing through protective impedance N
not exceeding the limits specified in 8.1.4
If a conductor of a printed board becomes open-circuited, the appliance is considered -
to have withstood the particular test, provided all three of the following conditions are
met:
- the material of the printed circuit board withstands N
the burning test of annex E
- any loosened conductor does not reduce the N
clearances or creepage distances between live parts
and accessible metal parts below the values
specified in cl. 29

Accredited Testing Laboratory

 Page 28 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

- the appliance withstands the tests of 19.11.2 with N

open-circuited conductor bridged
19.11.4 Appliances having a device with an off position N
obtained by electronic disconnection, or
a device that can be placed in the stand-by mode, N
subjected to the tests of 19.11.4.1 to 19.11.4.7 N
Appliances incorporating a protective electronic N
circuit subjected to the tests of 19.11.4.1 to 19.11.4.7,
except that
appliances operated for 30 s or 5 min during the test N
of 19.7 are not subjected to the tests for
electromagnetic phenomena.
During the test of the stand-by-mode, a suitable N
vessel is placed o, the cooking zone if a pan detector
is incorporate. (IEC 60335-2-6:2002)
19.11.4.1 The appliance is subjected to electrostatic discharges N
in accordance with IEC 61000-4-2, test level 4
19.11.4.2 The appliance is subjected to radiated fields in N
accordance with IEC 61000-4-3, test level 3
19.11.4.3 The appliance is subjected to fast transient bursts in N
accordance with IEC 61000-4-4, test level 3 or 4 as
specified
19.11.4.4 The power supply terminals of the appliance N
subjected to voltage surges in accordance with IEC
61000-4-5, test level 3 or 4 as specified
Earthed heating elements in class I appliances N
disconnected
19.11.4.5 The appliance is subjected to injected currents in N
accordance with IEC 61000-4-6, test level 3
19.11.4.6 The appliance is subjected to the Class 3 voltage N
dips and interruptions in accordance with IEC 61000-
4-11
19.11.4.7 The appliance is subjected to mains signals in N
accordance with IEC 61000-4-13, test level class 2

Accredited Testing Laboratory

 Page 29 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

19.11.4.8 The appliance is supplied at rated voltage and N

operated under normal operation. After 60s the
power supply is reduces to a level such that the
appliance ceases to respond or a programmable
component cease to operate.
The appliance continues to operate normally or N
requires a manual operation to restart
19.12 If the safety of the appliance for any of the fault N
conditions specified in 19.11.2 depends on the
operation of a miniature fuse-link complying with
IEC 60127, the test is repeated, measuring the
current flowing through the fuse-link; measured
current (A); rated current of the fuse-link (A) ...........:
19.13 During the tests the appliance does not emit flames, P
molten metal, poisonous or ignitable gas in
hazardous amounts
Temperature rises not exceeding the values shown (see appended table) P
in table 9
Enclosures not deformed to such an extent that N
compliance with cl. 8 is impaired
If the appliance can still be operated it complies with N
20.2
Insulation, other than of class III appliance, withstand the electric strength test of 16.3, -
the test voltage specified in table 4:
- basic insulation .......................................................: 1000 V P
- supplementary insulation .......................................: N
- reinforced insulation ...............................................: 3000 V P
After operation or interruption of a control, clearances P
and creepage distances across the functional
insulation withstanding the electric strength test of
16.3. the test voltage being twice the working voltage
The appliance does not undergo a dangerous N
malfunction, and
no failure of protective electronic circuits, if the N
appliance is still operable
Appliances tested with an electronic switch in the off position, or in the stand-by mode: -

Accredited Testing Laboratory

 Page 30 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

- do not become operational, or N

- if they become operational, do not result in a N
dangerous malfunction during or after the tests of
19.11.4
Ovens: temperature in the center of the oven not N
exceed 425°C before opening (IEC 60335-2-
6:2002)
Temperature rise of the windings of induction hob N
elements and induction wok elements not exceed
the values specified in 19.7 (IEC 60335-2-6:2002)
Electric strength test of induction hob elements and N
induction wok elements is carried out immediately
after switching of the appliance (IEC 60335-2-
6:2002)
Glass in oven doors shall not be damaged N
(60335-2-6)
19.14 Appliances operated under the conditions of Clause N
11. Contactors or relays contacts operating under the
conditions of clause 11 short-circuited
19.101 Induction hob elements: test conditions according to N
the standard; diameter of the disc (cm) (IEC
60335-2-6)
19.102 Induction hob element and induction wok elements N
operated under normal operation at rated voltage
but with thermal controls short-circuited. (IEC
60335-2-6:2002)
Temperature rise of the oil not exceed 270 K: N
(IEC 60335-2-6:2002)

20 STABILITY AND MECHANICAL HAZARDS -

20.1 Adequate stability P
Tilting test through an angle of 10° (appliance placed P
on an inclined plane/horizontal plane); appliance
does not overturn
Tilting test repeated on appliances with heating P
elements, angle of inclination increased to 15°
Possible heating test in overturned position; N
temperature rise does not exceed values shown in
table 9

Accredited Testing Laboratory

 Page 31 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

20.2 Moving parts adequately arranged or enclosed as to N

provide protection against personal injury
Protective enclosures, guards and similar parts are N
non-detachable
Adequate mechanical strength and fixing of N
protective enclosures
Self-resetting thermal cut-outs and overcurrent N
protective devices not causing a hazard, by
unexpected reclosure
Not possible to touch dangerous moving parts with N
test probe
20.101 Cooking range and ovens shall have adequate stability when the open the door is -
subjected to a load (IEC 60335-2-6:2002)
Appliance subjected to a load test and by the test of N
20.102 if relevant : mass (kg) :
Cooking ranges are tested without fitting any N
stabilizing means that are specified in the
instructions of installation.
Cooking range incorporating a storage N
compartment adjacent to the oven and which the
shelves are pulled out simultaneously:
Shelve subjected to a load test : mass (g)
The appliance shall not tilt N
Damage and deformation of doors are ignored
20.102 For cooking ranges normally placed on the floor and with horizontally hinged oven -
doors with a hinge height of less than 430mm from the floor, the test of 20.101 is
repeated except that: (IEC 60335-2-6:2002)
-The cooking range is fitted with the stabilizing N
means, if any, specified in the instructions for
installation
-The mass of the load on the oven doors is N
increased to 50kg, or the mass of 22,5kg is placed
at the center of the outer edge of the oven door,
whichever gives the most unfavourable results
The appliance shall not tilt N
Damage and deformation of doors are ignored

21 MECHANICAL STRENGTH -
21.1 Appliance has adequate mechanical strength and is P
constructed as to withstand rough handling

Accredited Testing Laboratory

 Page 32 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

Checked by applying blows to the appliance in P

accordance with test Ehb of IEC 60068-2-75, spring
hammer test, impact energy 0,5 J
If necessary, supplementary or reinforced insulation N
subjected to the electric strength test of 16.3
If necessary, repetition of groups of three blows on a N
new sample
Additional blows applied to the centre of glass doors N
(IEC 60335-2-6:2002)
The glass shall not fracture (IEC 60335-2-6:2002) N
Appliance incorporating visibly glowing heating elements enclosed in glass tubes, -
the blows are applied to the tubes as mounted in the appliance if they are : (IEC
60335-2-6:2002)
-located at the top of the oven and accessible to N
test probe 41 of IEC 61032
-located elsewhere in the oven and accessible to N
test probe B of IEC 61032
Hob surfaces of glass-ceramic or similar material: N
three blows applied on surfaces not exposed during
test of 21.102; impact energy 0,7 ± 0,05 J
(IEC 60335-2-6:2002)
Temperature-sensing probe subjected to one cycle N
of test according to 15.101 and 16.2
(IEC 60335-2-6:2002)
21.2 Accessible parts of solid insulation having strength to Terminal block P
prevent penetration by sharp implements
The insulation is tested as specified, unless Supplementary :1mm P
the thickness of supplementary insulation is at least 1 P
mm and reinforced insulation is at least 2 mm
21.101 Oven shelves and their supports shall have N
adequate mechanical strength (IEC 60335-2-
6:2002)
Total mass (kg) of the vessel, 220 times the volume N
of the useful oven space in m³, or 24kg, whichever
is less:
After the test the shelf and supports shall show no N
distortion impairing their further and
the shelf shall not fall from the supports N

Accredited Testing Laboratory

 Page 33 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

Ovens with shelves that can be withdrawn and with N

stops: force of 80N, vessel with side dimensions
200mm
The shelf shall not tilt downwards by more than 6° N
21.102 Hob surfaces of glass-ceramic and similar materials N
shall withstand the stresses liable to occur in normal
use (IEC 60335-2-6:2002)
After the test, the hob surface not crack and the N
appliance withstand the electric strength test of 16.3
21.103 Temperature-sensing probes shall be constructed N
so that they are not damaged when trapped in the
oven door (IEC 60335-2-6:2002)
After the test, the probe then complies with 8.1, N
15.101 and Cl. 29
21.104 Glass panels of horizontally hinged oven doors shall N
withstand the thermal shock liable to occur in
normal use (IEC 60335-2-6:2002)
After the test, the glass shall not fracture N

22 CONSTRUCTION -
22.1 Appliance marked with the first numeral of the IP N
system, relevant requirements of IEC 60529 are
fulfilled
22.2 Stationary appliance: means to provide all-pole disconnection from the supply -
provided, the following means being available:
- a supply cord fitted with a plug P
- a switch complying with 24.3 N
- a statement in the instruction sheet that a N
disconnection incorporated in the fixed wiring is to be
provided
- an appliance inlet N
Singe-pole switches and single-pole protective P
devices for the disconnection of heating elements in
single-phase, permanently connected class 01 and
class I appliances, connected to the phase conductor
22.3 Appliance provided with pins: no undue strain on N
socket-outlets
Applied torque not exceeding 0.25 Nm N

Accredited Testing Laboratory

 Page 34 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

Pull force of 50N to each pin after the appliance has N

being placed in the heating cabinet; when cooled to
room temperature the pins are not displaced by more
than 1mm
Each pin subjected to a torque of 0.4Nm; the pins are N
not rotating unless rotating does not impair
compliance with the standard
22.4 Appliance for heating liquids and appliance causing N
undue vibration not provided with pins for insertion
into socket-outlets
22.5 No risk of electric shock when touching the pins of N
the plug, for appliances having a capacitor with rated
capacitance exceeding 0,1µF, the appliance being
disconnected from the supply at the instant of voltage
peak
22.6 Instead of coloured water, a solution composed of P
0,6 ml of the rinsing agent per litre of distilled water
is used IEC 60335-2-5, Annex AA
Electrical insulation of Class II appliances not affected N
in case of a hose rupture or seal leak
22.7 Adequate safeguards against the risk of excessive N
pressure in appliances provided with steam-
producing devices
22.8 Electrical connections not subject to pulling during P
cleaning of compartments to which access can be
gained without the aid of a tool, and that are likely to
be cleaned in normal use
22.9 Insulation, internal wiring, windings, commutators and P
slip rings not exposed to oil, grease or similar
substances
Adequate insulating properties of oil or grease to Not used oil or grease P
which insulation is exposed
22.10 Not possible to reset voltage-maintained non-self- N
resetting thermal cut-outs by the operation of an
automatic switching device incorporated within the
appliance
Non-self resetting thermal motor protectors have a N
trip-free action, unless

Accredited Testing Laboratory

 Page 35 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

they are voltage maintained N

Location or protection of reset buttons of non-self- N
resetting controls is so that accidental resetting is
unlikely
22.11 Reliable fixing of non-detachable parts that provide P
the necessary degree of protection against electric
shock, moisture or contact with moving parts
Obvious locked position of snap-in devices used for P
fixing such parts
No deterioration of the fixing properties of snap-in P
devices used in parts that are likely to be removed
during installation or servicing
Tests as described P
22.12 Handles, knobs etc. fixed in a reliable manner P
Fixing in wrong position of handles, knobs etc. P
indicating position of switches or similar components
not possible
Axial force 15 N applied to parts, the shape being so P
that an axial pull is unlikely to be applied
Axial force 30 N applied to parts, the shape being so N
that an axial pull is likely to be applied
22.13 Unlikely that handles, when gripped as in normal use, P
make the operators hand touch parts having a
temperature rise exceeding the value specified for
handles which are held for short periods only
22.14 No ragged or sharp edges creating a hazard for the P
user in normal use, or during user maintenance
No exposed pointed ends of self tapping screws etc., P
liable to be touched by the user in normal use or
during user maintenance
22.15 Storage hooks and the like for flexible cords smooth N
and well rounded
22.16 Automatic cord reels cause no undue abrasion or N
damage to the sheath of the flexible cord, no
breakage of conductors strands, no undue wear of
contacts

Accredited Testing Laboratory

 Page 36 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

Cord reel tested with 6000 operations, as specified N

Electric strength test of 16.3, voltage of 1000 V N
applied
22.17 Spacers not removable from the outside by hand or N
by means of a screwdriver or a spanner
22.18 Current-carrying parts and other metal parts resistant P
to corrosion under normal conditions of use
22.19 Driving belts not used as electrical insulation Not used N
22.20 Direct contact between live parts and thermal P
insulation effectively prevented, unless material used
is non-corrosive, non-hygroscopic and non-
combustible
Compliance is checked by inspection and, if P
necessary, by appropriate test
22.21 Wood, cotton, silk, ordinary paper and fibrous or Not used P
hygroscopic material not used as insulation, unless
impregnated
Magnesium oxide and mineral ceramic fibres are P
not considered as hygroscopic materials
(60335-2-6)
22.22 Appliances not containing asbestos P
22.23 Oils containing polychlorinated biphenyl (PCB) not P
used
22.24 Bare heating elements adequately supported N
In case of rupture, the heating conductor is unlikely to N
come in contact with accessible metal parts
22.25 Sagging heating conductors cannot come into contact N
with accessible metal parts
22.26 The insulation between parts operating at safety N
extra-low voltage and other live parts complies with
the requirements for double or reinforced insulation
22.27 Parts connected by protective impedance separated N
by double or reinforced insulation

Accredited Testing Laboratory

 Page 37 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

22.28 Metal parts of Class II appliances conductively N

connected to gas pipes or in contact with water:
separated from live parts by double or reinforced
insulation
22.29 Class II appliances permanently connected to fixed N
wiring so constructed that the required degree of
access to live parts is maintained after installation
22.30 Parts serving as supplementary or reinforced P
insulation fixed so that they cannot be removed
without being seriously damaged, or
so constructed that they cannot be replaced in an Terminal block P
incorrect position, and so that if they are omitted, the
appliance is rendered inoperable or manifestly
incomplete
22.31 Clearances and creepage distances over P
supplementary and reinforced insulation not reduced
below values specified in clause 29 as a result of
wear
Clearances and creepage distances between live P
parts and accessible parts not reduced below values
for supplementary insulation, if wires, screws etc.
become loose
22.32 Supplementary and reinforced insulation designed or P
protected against deposition of dirt or dust
Supplementary insulation of natural or synthetic N
rubber resistant to ageing, or arranged and
dimensioned so that creepage distances are not
reduced below values specified in 29.2
Ceramic material not tightly sintered, similar material N
or beads alone not used as supplementary or
reinforced insulation
Oxygen bomb test at 70 °C for 96 h and 16 h at room N
temperature
Insulating material in which heating conductors are P
embedded is considered to be basic insulation and
not reinforced insulation
22.33 Conductive liquids that are or may become N
accessible in normal use are not in direct contact with
live parts

Accredited Testing Laboratory

 Page 38 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

Electrodes not used for heating liquids N

For class II constructions, conductive liquids that are N
or may become accessible in normal use, not in
direct contact with basic or reinforced insulation
For class II constructions, conductive liquids which N
are in contact with live parts, not in direct contact with
reinforced insulation
22.34 Shafts of operating knobs, handles, levers etc. not P
live, unless the shaft is not accessible when the part
is removed
22.35 Handles, levers and knobs, held or actuated in N
normal use, not becoming live in the event of a failure
of basic insulation
Such parts being of metal, and their shafts or fixings N
are likely to become live in the event of a failure of
basic insulation, are either adequately covered by
insulation material or their accessible parts are
separated from their shafts or fixings by
supplementary insulation
This requirement does not apply to handles, levers N
and knobs on stationary appliances other than those
of electrical components, provided they are either
reliably connected to an earthing terminal or earthing
contact, or separated from live parts by earthed metal
22.36 Handles continuously held in the hand in normal use N
are so constructed that when gripped as in normal
use, the operators hand is not likely to touch metal
parts, unless they are separated from live parts by
double or reinforced insulation
22.37 Capacitors in Class II appliances not connected to N
accessible metal parts, unless complying with 22.42
Metal casings of capacitors in Class II appliances N
separated from accessible metal parts by
supplementary insulation, unless complying with
22.42
22.38 Capacitors not connected between the contacts of a N
thermal cut-out
22.39 Lamp holders used only for the connection of lamps N

Accredited Testing Laboratory

 Page 39 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

22.40 Motor-operated appliances and combined appliances N

intended to be moved while in operation, or having
accessible moving parts, fitted with a switch to control
the motor. The actuating member of the switch being
easily visible and accessible
Unless the appliance can operate continuously, N
automatically or remotely without giving rise to a
hazard, appliances for remote operation being fitted
with a switch. The actuating member of the switch
being easily visible and accessible.
22.41 No components, other than lamps, containing P
mercury
22.42 Protective impedance consisting of at least two N
separate components
Values specified in 8.1.4 not exceeded if any one of N
the components are short-circuited or open-circuited
22.43 Appliances adjustable for different voltages, N
accidental changing of the setting of the voltage
unlikely to occur
22.44 Appliances shall not have an enclosure that is shaped P
or decorated like a toy
22.45 When air is used as reinforced insulation, clearances N
not reduced below the values specified in 29.1.4 due
to deformation as a result of an external force applied
to the enclosure
22.46 Software used in protective electronic circuits is N
software class B or C .............................................. :
22.47 Appliances connected to the water mains withstand N
the water pressure expected in normal use
No leakage from any part, including any inlet water N
hose
22.48 Appliances connected to the water mains constructed N
to prevent backsiphonage of non-potable water
22.49 For remote operation, the duration of operation shall N
be set before the appliance can be started, unless
the appliance switches off automatically or can N
operate continuously without hazard

Accredited Testing Laboratory

 Page 40 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

22.50 Controls incorporated in the appliance take priority N

over controls actuated by remote operation
22.51 A control on the appliance being manually adjusted to N
the setting for remote operation before the appliance
can be operated in this mode
There is a visual indication showing that the appliance N
is adjusted for remote operation
Manual setting and visual indication not necessary on appliances that can operate as -
follows, without giving rise to a hazard:
- operate continuously, N
- operate automatically, or N
- be operated remotely N
It is not necessary to manually adjust to the setting for N
remote operation in order to switch the appliance off.
(IEC 60335-2-6)
22.52 Socket-outlets on appliances accessible to the user in N
accordance with the socket-outlet system used in the
country in which the appliance is sold
22.101 Hob element prevented from rotating about vertical P
axis and (IEC 60335-2-6:2002)
adequately supported in all positions of adjustment P
of their supports (IEC 60335-2-6:2002)
Hobs constructed so that damage to is unlikely N
occur while the hob elements are being removed or
replaced, for hobs with detachable hob elements
(IEC 60335-2-6:2002)
22.102 Timers intended to delay the operation of a heating N
element shall not control a radiant grill, unless
(IEC 60335-2-6:2002)
the grill is thermally controlled and incorporated in a N
oven or other compartment
(IEC 60335-2-6:2002)
22.103 Ovens vents shall be constructed so that any N
moisture or grease discharged through them cannot
affect clearances and creepage distances between
live parts and other parts of the appliance
(IEC 60335-2-6:2002)
22.104 Steam ovens shall be constructed so that steam N
vents and ducts are unlikely to become blocked
during normal use (IEC 60335-2-6:2002)

Accredited Testing Laboratory

 Page 41 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

22.105 Built-in ovens shall only be vented through the front, N

unless (IEC 60335-2-6:2002)
provision is made for venting through a duct N
(IEC 60335-2-6:2002)
22.106 Grills shall be constructed so that grill can be easily N
positioned without jamming (IEC 60335-2-6:2002)
The grills pans shall not fall from the support when N
moved sideways (IEC 60335-2-6:2002)
22.107 Pyrolytic self-cleaning ovens shall switch off N
automatically at the end of the process and require
a manual operation to start another cleaning cycle
(IEC 60335-2-6:2002)
22.108 Pyrolytic self-cleaning ovens shall be constructed so N
that opening and closing of the door does not impair
the interlock system or damage the door seal; test
as specified (IEC 60335-2-6:2002)
After the test, the interlock system shall be fit for N
further use and the door seal shall not be damage
(IEC 60335-2-6:2002)
22.109 Pyrolytic self-cleaning ovens shall incorporate an N
interlock so that access to the oven cannot be
gained when the temperature in the centre of the
oven exceeds 350 °C. even if the interlock is
defective; test as specified (IEC 60335-2-6:2002)
22.110 Pyrolytic self-cleaning ovens shall be constructed so N
that ignitable gases cannot be discharged through
vents during the cleaning process; test as specified
(IEC 60335-2-6:2002)
22.111 Pyrolytic self-cleaning ovens: no risk of emission of N
flames; test as specified (60335-2-6)
22.112 Hobs shall be constructed so that hinged lids cannot N
close accidentally (IEC 60335-2-6:2002)
22.113 Hobs shall be constructed so that inadvertent N
operation of touch controls due to spillage of liquid
or damp cloth is unlikely; test as specified
(IEC 60335-2-6:2002)
22.114 Hobs having touch controls shall require at least two N
manual operations to switch on a hob element but
only one to switch off (IEC 60335-2-6:2002)
Additional hob elements may be switched on by N
single manual operation (IEC 60335-2-6:2002)
Hobs having touch controls shall incorporate visual N
means to indicate when each hob is energized
(IEC 60335-2-6:2002)

Accredited Testing Laboratory

 Page 42 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

22.115 Induction hob elements and induction wok N

elements, and other hob elements incorporating a
pan detector shall be constructed so that the hob
element operated can only be operated when a
vessel is placed on the cooking zone
(IEC 60335-2-6:2002)
Appliance operated at rated voltage: (IEC 60335-2- N
6:2002)
Temperature rise not exceed 35 K, for induction hob N
elements and induction wok elements : (IEC 60335-
2-6:2002)
Other hobs elements shall not operate N
(IEC 60335-2-6:2002)
22.116 Hob elements incorporating a pan detector shall be N
constructed so that the hob element is not switched
on by the vessel if is has been removed for more
than 10 min (IEC 60335-2-6:2002)
22.117 Appliances incorporating a pan detector a signal N
lamp shall indicate when the control for the hob
elements is not switched to the off position
(IEC 60335-2-6:2002)
22.118 If a plug of a supply cord is engaged in a N
socket-outlet located directly above the door, it shall
not be possible to operate a grill
(IEC 60335-2-6:2002)
22.119 Cooking ranges incorporating a retractable deflector N
to prevent excessive temperatures on control knobs
shall be constructed so that the user is unlikely to
touch hot surfaces of the deflector when operating
the controls (IEC 60335-2-6:2002)
22.120 Outer glass panels of oven doors shall be made N
from glass that breaks into small pieces when it
fractures (IEC 60335-2-6:2002)
22.121 Outer glass panels of oven doors that are intended N
to be removed by the user for cleaning shall be
constructed so that they cannot be fixed in an
incorrect orientation (IEC 60335-2-6:2002)
22.122 Ovens with shelves that can be withdrawn shall be N
fitted with rest positions (IEC 60335-2-6:2002)
The shelves shall also be constructed to prevent N
cooking dishes, or the like, from sliding over the rear
edge (IEC 60335-2-6:2002)

23 INTERNAL WIRING -

Accredited Testing Laboratory

 Page 43 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

23.1 Wireways smooth and free from sharp edges P

Wires protected against contact with burrs, cooling P
fins etc.
Wire holes in metal well rounded or provided with P
bushings
Wiring effectively prevented from coming into contact P
with moving parts
23.2 Beads etc. on live wires cannot change their position, P
and are not resting on sharp edges or corners
Beads inside flexible metal conduits contained within N
an insulating sleeve
23.3 Electrical connections and internal conductors N
movable relatively to each other not exposed to
undue stress
Flexible metallic tubes not causing damage to N
insulation of conductors
Open-coil springs not used N
Adequate insulating lining provided inside a coiled N
spring, the turns of which touch one another
No damage after 10 000 flexings for conductors N
flexed during normal use or 100 flexings for
conductors flexed during user maintenance
Electric strength test, 1000 V between live parts and N
accessible metal parts
The requirement also applies if parts of a cooking N
range are folded onto the hob surface or separated
from their normal position, for transportation
purposes (IEC 60335-2-6:2002)
23.4 Bare internal wiring sufficiently rigid and fixed N
23.5 The insulation of internal wiring withstanding the P
electrical stress likely to occur in normal use
No breakdown when a voltage of 2000 V is applied P
for 15 min between the conductor and metal foil
wrapped around the insulation
23.6 Sleeving used as supplementary insulation on N
internal wiring retained in position by positive means

Accredited Testing Laboratory

 Page 44 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

23.7 The colour combination green/yellow used only for P

earthing conductors
23.8 Aluminium wires not used for internal wiring P
23.9 No lead-tin soldering of stranded conductors where P
they are subject to contact pressure, unless
clamping means so constructed that there is no risk N
of bad contact due to cold flow of the solder
23.10 The insulation and sheath of internal wiring, N
incorporated in external hoses for the connection of
an appliance to the water mains, at least equivalent to
that of light polyvinyl chloride sheathed flexible cord
(60227 IEC 52)

24 COMPONENTS -
24.1 Components comply with safety requirements in P
relevant IEC standards
List of components (see appended table) P
Components not tested and found to comply with N
relevant IEC standard for the number of cycles
specified are tested in accordance with 24.1.1 to
24.1.9
Components not tested and found to comply with P
relevant IEC standard, components not marked or
not used in accordance with its marking, tested under
the conditions occurring in the appliance
Lampholders and starterholders not being tested and N
found to comply with the relevant IEC standard,
tested as a part of the appliance and additionally
according to the gauging and interchangeability
requirements of the relevant IEC standard
24.1.1 Capacitors likely to be permanently subjected to the N
supply voltage and used for radio interference
suppression or for voltage dividing, complying with
IEC 60384-14, or
tested according to annex F N
24.1.2 Safety isolating transformers complying with IEC N
61558-2-6, or

Accredited Testing Laboratory

 Page 45 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

tested according to annex G N

24.1.3 Switches complying with IEC 61058-1, the number of P
cycles of operation being at least 10 000, or
tested according to annex H N
If the switch operates a relay or contactor, the N
complete switching system is subjected to the test
Switches controlling hob elements subjected to N
30 000 cycles of operation (IEC 60335-2-6:2002)
24.1.4 Automatic controls complying with IEC 60730-1 with relevant part 2. The number of -
cycles of operation being:
- thermostats: 10 000 N
- temperature limiters: 1 000 N
- self-resetting thermal cut-outs: 300 N
- self-resetting thermal cut-outs for heating 100 000 N
elements of glass-ceramic hobs (IEC
60335-2-6:2002)
- self-resetting thermal cut-outs for heating 10 000 N
elements of other hobs
(IEC 60335-2-6:2002)
- voltage maintained non-self-resetting 1000 N
thermal cut-outs:
- other non-self-resetting thermal cut-outs: 30 N
- timers: 3 000 N
- energy regulators for automatic action 100 000 N
(IEC 60335-2-6:2002)
- energy regulators for manual action (IEC 10 000 N
60335-2-6:2002)
thermostats controlling the cleaning 3 000 N
process in pyrolytic self-cleanings ovens
(IEC 60335-2-6:2002)
Thermal motor protectors are tested in combination N
with their motor under the conditions specified in
Annex D
For water valves containing live parts and that are N
incorporated in external hoses for connection of an
appliance to the water mains, the degree of protection
declared for subclause 6.5.2 of IEC 60730-2-8 is
IPX7

Accredited Testing Laboratory

 Page 46 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

24.1.5 Appliance couplers complying with IEC 60320-1 N

However, appliances classified higher than IPX0, the N
appliance couplers complying with IEC 60320-2-3
Interconnection couplers complying with IEC 60320- N
2-2
24.1.6 Small lamp holders similar to E10 lampholders N
complying with IEC 60238, the requirements for E10
lampholders being applicable
24.1.7 If the remote operation of the appliance is via a N
telecommunication network, the relevant standard for
the telecommunication interface circuitry in the
appliance is IEC 62151
24.1.8 The relevant standard for thermal links is IEC 60691. N
Thermal links not complying with IEC 60691 are
considered to be an intentionally weak part for the
purposes of Clause 19
24.1.9 Relays, other than motor starting relays, tested as N
part of the appliance
They are also tested in accordance with Clause 17 of N
IEC 60730-1, the number of operations in 24.1.4
selected according to the relay function in the
appliance .................................................................. :
24.2 No switches or automatic controls in flexible cords P
No devices causing the protective device in the fixed P
wiring to operate in the event of a fault in the
appliance
No thermal cut-outs that can be reset by soldering N
24.3 Switches intended for all-pole disconnection of N
stationary appliances are directly connected to the
supply terminals and having a contact separation in
all poles, providing full disconnection under
overvoltage category III conditions
24.4 Plugs and socket-outlets for extra-low voltage circuits N
and heating elements, not interchangeable with plugs
and socket-outlets listed in IEC 60083 or IEC 60906-
1 or with connectors and appliance inlets complying
with the standard sheets of IEC 60320-1

Accredited Testing Laboratory

 Page 47 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

24.5 Capacitors in auxiliary windings of motors marked N

with their rated voltage and capacitance and used
accordingly
Voltage across capacitors in series with a motor N
winding does not exceed 1,1 times rated voltage,
when the appliance is supplied at 1,1 times rated
voltage under minimum load
24.6 Working voltage of motors connected to the supply N
mains and having basic insulation that is inadequate
for the rated voltage of the appliance, not exceeding
42V
In addition, the motors are complying with the N
requirements of Annex I
24.7 Hose-sets for connection of appliances to the water N
mains, complying with IEC 61770 and supplied with
the appliance
24.101 Thermostat and energy regulators incorporating an N
off position shall not switch on a result of variations
in ambient temperatures (IEC 60335-2-6:2002)
During the test, the off position shall be maintained N
No breakdown shall occur; test voltage 500 V N
24.102 Incorporated socket-outlets in cooking ranges: N
single-phase type, earthing contact, rated current
≤16 A, protected by fuses or circuit breaker placed
behind a non-detachable cover rated current not
exceeding rated current of the socket-outlet
(IEC 60335-2-6:2002)
Cooking range for permanently connected to fixed N
wiring or is fitted with a polarized plug, the neutral
pole need not be protected (IEC 60335-2-6:2002)
If fuses become accessible after opening a drawer N
or other compartment, a non-detachable cover is
not required (IEC 60335-2-6:2002)

25 SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CORDS -

25.1 Appliance not intended for permanent connection to fixed wiring, means for connection -
to the supply:
- supply cord fitted with a plug P

Accredited Testing Laboratory

 Page 48 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

- an appliance inlet having at least the same degree N

of protection against moisture as required for the
appliance
- pins for insertion into socket-outlets N
25.2 Appliance not provided with more than one means of P
connection to the supply mains
Stationary appliance for multiple supply may be N
provided with more than one means of connection,
provided electric strength test of 1250 V for 1 min
between each means of connection causes no
breakdown
25.3 Connection of supply conductors for appliance P
intended to be permanently connected to fixed wiring
possible after the appliance has been fixed to its
support
Appliance provided with a set of terminals for the P
connection of cables or fixed wiring, cross-sectional
areas specified in 26.6
Appliance provided with a set of terminals allowing P
the connection of a flexible cord
Appliance provided with a set of supply leads P
accommodated in a suitable compartment
Appliance provided with a set of terminals and cable N
entries, conduit entries, knock-outs or glands,
allowing connection of appropriate type of cable or
conduit
Connection of supply wires of hobs, built-in ranges P
and built-in ovens may be made before the
appliance is installed (IEC 60335-2-6:2002)
25.4 Cable and conduit entries, rated current of appliance P
not exceeding 16 A, dimension according to table 10
Introduction of conduit or cable does not reduce P
clearances or creepage distances below values
specified in 29
25.5 Method for assemble supply cord with the appliance: -
- type X attachment N
- type Y attachment P

Accredited Testing Laboratory

 Page 49 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

- type Z attachment, if allowed in part 2 N

Type X attachment, other than those with a specially N
prepared cord, not used for flat twin tinsel cords
25.6 Plugs fitted with only one flexible cord P
25.7 Supply cords being one of the following types: -
- rubber sheathed (at least 60245 IEC 53) N
- polychloroprene sheathed (at least 60245 IEC 57) N
- cross-linked polyvinyl chloride sheathed (at least N
60245 IEC 87)
Polyvinyl chloride sheathed: -
Not used if they are likely to touch metal parts having a temperature rise exceeding
75K during the test of Clause 11.
- light polyvinyl chloride sheathed cord (at least 60227 N
IEC 52), appliances not exceeding 3 kg
- ordinary polyvinyl chloride sheathed cord (at least H05VV-F P
60227 IEC 53), other appliances
Heat resistant polyvinyl chloride sheathed: N
Not used for type X attachment other than specially prepared cords.
- Heat-resistant light polyvinyl chloride sheathed cord N
(at least 60227 IEC 56), appliances not exceeding
3 kg
- heat-resistant polyvinyl chloride sheathed cord N
(60227 IEC 57), other appliances
25.8 Nominal cross-sectional area of supply cords Rated current: 15.2 A P
according to table 11; rated current (A); cross- Cross-sectional area: 1.5mm²
2
sectional area (mm²) ................................................ : (allowed: 1.5 mm ).
25.9 Supply cord not in contact with sharp points or edges P
25.10 Green/yellow core for earthing purposes in Class I P
appliance
25.11 Conductors of supply cords not consolidated by lead- P
tin soldering where they are subject to contact
pressure, unless
clamping means so constructed that there is no risk P
of bad contacts due to cold flow of the solder

Accredited Testing Laboratory

 Page 50 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

25.12 Moulding the cord to part of the enclosure does not P

damage the insulation of the supply cord
25.13 Inlet opening so shaped as to prevent damage to the P
supply cord
Unless the enclosure at the inlet opening is of P
insulation material, a non-detachable lining or
bushing complying with 29.3 for supplementary
insulation provided
If unsheathed supply cord, a similar additional N
bushing or lining is required, unless
the appliance is class 0 N
25.14 Supply cords adequately protected against excessive N
flexing
Flexing test: -
- applied force (N) .................................................... : N
- number of flexings ................................................. : N
The test does not result in: -
- short circuit between the conductors N
- breakage of more than 10% of the strands of any N
conductor
- separation of the conductor from its terminal N
- loosening of any cord guard N
- damage, within the meaning of the standard, to the N
cord or the cord guard
- broken strands piercing the insulation and becoming N
accessible
For temperature-sensing probes, the total number N
of flexings is 5 000. (IEC 60335-2-6:2002)
Probes with circular section cords are turned N
through 90° after 2 500 flexings(IEC 60335-2-
6:2002)
25.15 Conductors of the supply cord relieved from strain, P
twisting and abrasion by use of cord anchorage

Accredited Testing Laboratory

 Page 51 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

The cord cannot be pushed into the appliance to such P

an extent that the cord or internal parts of the
appliance can be damaged
Pull and torque test of supply cord, values shown in 100N P
table 10: pull (N); torque (not on automatic cord reel)
0.35Nm
(Nm) ......................................................................... :
Max. 2 mm displacement of the cord, and conductors P
not moved more than 1 mm in the terminals
Creepage distances and clearances not reduced P
below values specified in 29.1
25.16 Cord anchorages for type X attachments constructed and located so that: -
- replacement of the cord is easily possible N
- it is clear how the relief from strain and the N
prevention of twisting are obtained
- they are suitable for different types of cord N
- cord cannot touch the clamping screws of cord N
anchorage if these screws are accessible, unless
separated from accessible metal parts by
supplementary insulation
- the cord is not clamped by a metal screw which N
bears directly on the cord
- at least one part of the cord anchorage securely N
fixed to the appliance, unless part of a specially
prepared cord
- screws which have to be operated when replacing N
the cord do not fix any other component, if applicable
- if labyrinths can be bypassed the test of 25.15 is N
nevertheless withstood
- for Class 0, 0I and I appliances: they are of N
insulating material or are provided with an insulating
lining, unless a failure of the insulation of the cord
does not make accessible metal parts live
- for Class II appliances: they are of insulating N
material, or if of metal, they are insulated from
accessible metal parts by supplementary insulation

Accredited Testing Laboratory

 Page 52 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

25.17 Adequate cord anchorages for type Y and Z P

attachment
25.18 Cord anchorages only accessible with the aid of a P
tool, or
so constructed that the cord can only be fitted with the N
aid of a tool
25.19 Type X attachment, glands not used as cord N
anchorage in portable appliances
Tying the cord into a knot or tying the cord with string N
not used
25.20 Conductors of the supply cord for type Y and Z P
attachment adequately additionally insulated
25.21 Space for supply cord for type X attachment or for N
connection of fixed wiring constructed to permit
checking of conductors with respect to correct
positioning and connection before fitting any cover, no
risk of damage to the conductors when fitting the
cover, no contact with accessible metal parts if a
conductor becomes loose, etc.
For portable appliances, the uninsulated end of a N
conductor prevented from any contact with accessible
metal parts, unless the end of the cord is such that
the conductors are unlikely to slip free
25.22 Appliance inlet: -
- live parts not accessible during insertion or removal N
- connector can be inserted without difficulty N
- the appliance is not supported by the connector N
- is not for cold conditions if temp. rise of external N
metal parts exceeds 75 K, unless the supply cord is
not likely to touch such metal parts
25.23 Interconnection cords comply with the requirements N
for the supply cord, except as specified
If necessary, electric strength test of 16.3 N
25.24 Interconnection cords not detachable without the aid N
of a tool if compliance with the standard is impaired
when they are disconnected

Accredited Testing Laboratory

 Page 53 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

25.25 Dimensions of pins compatible with the dimensions of N

the relevant socket-outlet. Dimensions of pins and
engagement face in accordance with the relevant
plug in IEC 60083

26 TERMINALS FOR EXTERNAL CONDUCTORS -

26.1 Appliances provided with terminals or equally P
effective devices for connection of external
conductors
Terminals only accessible after removal of a non- P
detachable cover
However, earthing terminals may be accessible if a N
tool is required to make the connections and means
are provided to clamp the wire independently from its
connection
26.2 Appliances with type X attachment and appliances for N
connection to fixed wiring provided with terminals in
which connections are made by means of screws,
nuts or similar devices, unless the connections are
soldered
Screws and nuts serve only to clamp supply N
conductors, except
internal conductors, if so arranged that they are N
unlikely to be displaced when fitting the supply
conductors
If soldered connections used, the conductor so N
positioned or fixed that reliance is not placed on
soldering alone
Soldering alone used, barriers provided, clearances N
and creepage distances satisfactory if the conductor
becomes free at the soldered joint
26.3 Terminals for type X attachment and for connection N
to fixed wiring so constructed that the conductor is
clamped between metal surfaces with sufficient
contact pressure and without damaging the conductor
Terminals for type X attachment and those for connection to fixed wiring so fixed that -
when tightening or loosening the clamping means:
- the terminal does not loosen N

Accredited Testing Laboratory

 Page 54 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

- internal wiring is not subjected to stress N

- clearances and creepage distances are not reduced N
below the values in 29
Compliance checked by inspection and by the test of N
subclause 9.6 of IEC 60999-1, the torque applied
being equal to two-thirds of the torque specified.
Nominal diameter of thread (mm); screw category;
torque (Nm):
26.4 Terminals for type X attachment, except those with a N
specially prepared cord, and those for connection to
fixed wiring, no special preparation of conductors
required, and so constructed or placed that
conductors prevented from slipping out
26.5 Terminals for type X attachment so located or N
shielded that if a wire of a stranded conductor
escapes, no risk of accidental connection to other
parts that result in a hazard
Stranded conductor test, 8 mm insulation removed N
No contact between live parts and accessible metal N
parts and, for class II constructions, between live
parts and metal parts separated from accessible
metal parts by supplementary insulation only
26.6 Terminals for type X attachment and for connection N
to fixed wiring suitable for connection of conductors
with required cross-sectional area according to
table 13; rated current (A); nominal cross-sectional
area (mm²) ............................................................... :
Terminals only suitable for a specially prepared cord N
26.7 Terminals for type X attachment accessible after N
removal of a cover or part of the enclosure
26.8 Terminals for the connection to fixed wiring, including P
the earthing terminal, located close to each other
26.9 Terminals of the pillar type constructed and located N
as specified
26.10 Terminals with screw clamping and screwless N
terminals not used for flat twin tinsel cords, unless
conductors ends fitted with a device suitable for
screw terminals

Accredited Testing Laboratory

 Page 55 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

Pull test of 5 N to the connection N

26.11 For type Y and Z attachment: soldered, welded, N
crimped and similar connections may be used
For Class II appliances: the conductor so positioned N
or fixed that reliance is not placed on soldering,
welding or crimping alone
For Class II appliances: soldering, welding or N
crimping alone used, barriers provided, clearances
and creepage distances satisfactory if the conductor
becomes free

27 PROVISION FOR EARTHING -

27.1 Accessible metal parts of Class 0I and I appliances, P
permanently and reliably connected to an earthing
terminal or contact of the appliance inlet
Earthing terminals not connected to neutral terminal P
Class 0, II and III appliance have no provision for N
earthing
Safety extra-low voltage circuits not earthed, unless P
protective extra-low voltage circuits
27.2 Clamping means adequately secured against P
accidental loosening
Terminals used for the connection of external N
equipotential bonding conductors allow connection of
conductors of 2.5 to 6 mm², and
do not provide earthing continuity between different N
parts of the appliance
Conductors cannot be loosened without the aid of a N
tool
27.3 For detachable parts that are plugged into another N
part of the appliance, and having an earth connection,
the earth connection made before and separated
after current-carrying connections when removing the
part

Accredited Testing Laboratory

 Page 56 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

For appliances with supply cord, current-carrying N

conductors become taut before earthing conductor, if
the cord slips out of the cord anchorage
27.4 No risk of corrosion resulting from contact between P
metal of earthing terminal and other metal
Adequate resistance to corrosion of coated or P
uncoated parts providing earthing continuity, other
than parts of a metal frame or enclosure
Parts of steel providing earthing continuity provided at N
the essential areas with an electroplated coating,
thickness at least 5 µm
Adequate protection against rusting of parts of coated P
or uncoated steel, only intended to provide or transmit
contact pressure
In case of aluminium alloys precautions taken to N
avoid risk of corrosion
27.5 Low resistance of connection between earthing P
terminal and earthed metal parts
This requirement does not apply to connections N
providing earthing continuity in the protective extra-
low voltage circuit, provided that clearances of basic
insulation are based on the rated voltage of the
appliance
Resistance not exceeding 0,1 Ω at the specified low- 0,05 Ω P
resistance test
27.6 The printed conductors of printed circuit boards shall N
not be used to provide earthing continuity in hand-
held appliances.
They may be used to provide earthing continuity in N
other appliances if at least two tracks are used with
independent soldering points and the appliance
complies with 27.5 for each circuit
28 SCREWS AND CONNECTIONS -
28.1 Fixings, electrical connections and connections P
providing earthing continuity withstand mechanical
stresses
Screws not of soft metal liable to creep, such as zinc P
or aluminium

Accredited Testing Laboratory

 Page 57 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

Diameter of screws of insulating material min. 3 mm N

Screws of insulating material not used for any N
electrical connection or connections providing
earthing continuity
Screws used for electrical connections or connections P
providing earthing continuity screw into metal
Screws not of insulating material if their replacement N
by a metal screw can impair supplementary or
reinforced insulation
Type X attachment, screws to be removed for N
replacement of supply cord or for user maintenance,
not of insulating material if their replacement by a
metal screw can impair basic insulation
For screws and nuts; test as specified (see appended table) P
28.2 Electrical connections and connections providing P
earthing continuity constructed so that contact
pressure not transmitted through insulating material
liable to shrink or distort, unless shrinkage or
distortion compensated
This requirement does not apply to electrical N
connections in circuits carrying a current not
exceeding 0.5A
28.3 Space-threaded (sheet metal) screws only used for N
electrical connections if they clamp the parts together
Thread-cutting (self-tapping) screws and thread N
rolling screws only used for electrical connections if
they generate a full form standard machine screw
thread
Thread-cutting (self-tapping) screws not used if they N
are likely to be operated by the user or installer
Thread-cutting, thread rolling and space threaded screws may be used in connections -
providing earthing continuity provided it is not necessary to disturb the connection:
- in normal use, N
- during user maintenance, N
- when replacing a supply cord having a type X N
attachment, or

Accredited Testing Laboratory

 Page 58 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

- during installation N
At least two screws being used for each connection N
providing earthing continuity, unless
the screw forms a thread having a length of at least N
half the diameter of the screw
Thread-cutting and space-threaded screws may be N
used in connections providing earthing continuity,
provided unnecessary to disturb the connection and
at least two screws are used for each connection
28.4 Screws and nuts that make mechanical connection P
secured against loosening if they also make electrical
connections or connections providing earthing
continuity
Rivets for electrical connections or connections N
providing earthing continuity secured against
loosening if subjected to torsion

29 CLEARANCES, CREEPAGE DISTANCES AND SOLID INSULATION -

Clearances, creepage distances and solid insulation P
withstand electrical stress
For coatings used on printed circuits boards to N
protect the microenvironment (Type 1) or to provide
basic insulation (Type 2), annex J applies............... :
The microenvironment is pollution degree 1 under N
Type 1 coating
No clearance or creepage distance requirements N
under Type 2 coating
29.1 Clearances not less than the values specified in table P
16, taking into account the rated impulse voltage for
the overvoltage categories of table 15, unless
for basic insulation and functional insulation they P
comply with the implulse voltage test of clause 14
However, if the construction is affected by wear, P
distortion, movement of the parts or during assembly,
the clearances for rated impulse voltages of 1500V
and above are increased by 0,5 mm and the impulse
voltage test is not applicable

Accredited Testing Laboratory

 Page 59 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

Impulse voltage test not applicable: -

- when the microenvironment is pollution degree 3 P
- for basic insulation of class 0 and class 01 P
appliances
Appliances are in overvoltage category II P
Clearances less than specified in table 16 not allowed N
for basic insulation of class 0 and class 0I appliances,
or if pollution degree 3 is applicable P
Compliance is checked by inspection and P
measurements as specified
29.1.1 Clearances of basic insulation withstand the P
overvoltages, taking into account the rated impulse
voltage
Clearance at the terminals of tubular sheathed N
heating elements may be reduced to 1mm if the
microenvironment is pollution degree 1
Lacquered conductors of windings considered to be N
bare conductors
29.1.2 Clearances of supplementary insulation not less than N
those specified for basic insulation in table 16
29.1.3 Clearances of reinforced insulation not less than P
those specified for basic insulation in table 16, but
using the next higher step for rated impulse voltage
29.1.4 For functional insulation, the values of table 16 are P
applicable, unless
the appliance complies with clause 19 with the N
functional insulation short-circuited
Lacquered conductors of windings considered to be N
bare conductors
However, clearances at crossover points are not N
measured
Clearance between surfaces of PTC heating N
elements may be reduced to 1mm

Accredited Testing Laboratory

 Page 60 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

29.1.5 Appliances having higher working voltage than rated N

voltage, the voltage used for determining clearances
from table 16 is the sum of the rated impulse voltage
and the difference between the peak value of the
working voltage and the peak value of the rated
voltage
If the secondary winding of a step-down transformer N
is earthed, or if there is an earthed screen between
the primary and secondary windings, clearances of
basic insulation on the secondary side not less than
those specified in table 16, but using the next lower
step for rated impulse voltage
Circuits supplied with a voltage lower than rated N
voltage, clearances of functional insulation based on
the working voltage used as the rated voltage in table
15
29.2 Creepage distances not less than those appropriate P
for the working voltage, taking into account the
material group and the pollution degree
Pollution degree 2 applies, unless N
precautions taken to protect the insulation; pollution N
degree 1
insulation subjected to conductive pollution; pollution P
degree 3
Compliance is checked by inspection and P
measurements as specified
The microenvironment is pollution degree 3 unless P
the insulation is enclosed or located so that it is
unlikely to be exposed to pollution during normal
use of the appliance
(IEC 60335-2-6:2002) (IEC 60335-2-13:2002)
29.2.1 Creepage distances of basic insulation not less than P
specified in table 17
For pollution degree 1, creepage distance not less N
than the minimum specified for the clearance in table
16, if the clearance has been checked according to
the test of clause 14
29.2.2 Creepage distances of supplementary insulation at N
least as specified for basic insulation in table 17

Accredited Testing Laboratory

 Page 61 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

29.2.3 Creepage distances of reinforced insulation at least P

double as specified for basic insulation in table 17
29.2.4 Creepage distances of functional insulation not less P
than specified in table 18
Creepage distances may be reduced if the appliance N
complies with clause 19 with the functional insulation
short-circuited
29.3 Supplementary and reinforced insulation having N
adequate thickness, or a sufficient number of layers,
to withstand the electrical stresses
Compliance checked by: -
- measurement, in accordance with 29.3.1, or N
- an electric strength test in accordance with 29.3.2, N
or
- an assessment of the thermal quality of the material N
combined with an electric strength test, in accordance
with 29.3.3
This requirement does not apply to the sheath of N
visibly glowing heating element inaccessible to test
probe 41 of IEC 61032 (IEC 60335-2-6:2002)
29.3.1 Supplementary insulation having a thickness of at Cover of terminal block P
least 1 mm
Reinforced insulation having a thickness of at least 2 N
mm
29.3.2 Each layer of material withstand the electric strength N
test of 16.3 for supplementary insulation
Supplementary insulation consisting of at least 2 N
layers
Reinforced insulation consisting of at least 3 layers N
29.3.3 The insulation is subjected to the dry heat test Bb of N
IEC 60068-2-2, followed by
the electric strength test of 16.3 N
If the temperature rise during the tests of Clause 19 N
does not exceed the value specified in Table 3, the
test of IEC 60068-2-2 is not carried out

Accredited Testing Laboratory

 Page 62 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

30 RESISTANCE TO HEAT AND FIRE -

30.1 External parts of non-metallic material, P
parts supporting live parts, and P
thermoplastic material providing supplementary or P
reinforced insulation,
sufficiently resistant to heat P
Ball-pressure test according to IEC 60695-10-2 P
External parts: at 40 °C plus the maximum P
temperature rise determined during the test of clause
11, or at 75 °C, whichever is the higher; temperature
(°C)............................................................................:
Parts supporting live parts: at 40°C plus the P
maximum temperature rise determined during the
test of clause 11, or at 125°C, whichever is the
higher; temperature (°C) ..........................................:
Parts of thermoplastic material providing P
supplementary or reinforced insulation, 25°C plus the
maximum temperature rise determined during clause
19, if higher; temperature (°C)..................................:
30.2 Parts of non-metallic material adequately resistant to P
ignition and spread of fire
This requirement does not apply to decorative trims, P
knobs and other parts unlikely to be ignited or to
propagate flames that originate inside the appliance
Compliance checked by the test of 30.2.1. N
In addition:
- attended appliances, 30.2.2 applies N
- unattended appliances, 30.2.3 applies P
Appliances for remote operation, 30.2.3 applies N
Base material of printed circuit board, 30.2.4 applies N
For induction wok elements, grills and griddles that N
do not incorporate a timer , 30.2.2 is applicable (IEC
60335-2-6:2002)

Accredited Testing Laboratory

 Page 63 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

For other appliances, 30.2.3 is applicable (IEC P

60335-2-6:2002)
30.2.1 Glow-wire test of IEC 60695-2-11 at 550 °C, unless P
the material is classified at least HB40 according to N
IEC 60695-11-10
Parts for which the glow-wire test cannot be carried N
out meet the requirements in ISO9772 for category
HBF material
30.2.2 Appliances operated while attended, parts of non- N
metallic material supporting current-carrying
connections, and parts of non-metallic material within
a distance of 3mm of such connections, are
subjected to the glow-wire test of IEC 60695-2-11.
The glow-wire test is not carried out on parts of material classified as having a glow- -
wire flammability index according to IEC 60695-2-12 of at least:
-750°C, for connections carrying a current exceeding N
0,5A during normal operation
-650°C, for other connections N
Test as specified for an interposed shielding material N
When the glow-wire test of IEC 60695-2-11 is carried out, the temperatures are: -
-750°C, for connections carrying a current exceeding N
0,5A during normal operation
-650°C, for other connections N
Test not applicable to conditions as specified N
30.2.3 Appliances operated while unattended, tested as P
specified in 30.2.3.1 and 30.2.3.2
Tests not applicable to conditions as specified N
30.2.3.1 Parts of insulating material supporting connections P
carrying a current exceeding 0.2A during normal
operation, and
parts of non-metallic material within a distance of P
3mm,
subjected to the glow-wire test of IEC 60695-2-11 P
with a test severity of 850°C

Accredited Testing Laboratory

 Page 64 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

Glow-wire test not carried out on parts of material N

classified as having a glow-wire flammability index of
at least 850°C according to IEC 60695-2-12
Glow-wire test not carried out on small parts that N
comply with the needle-flame test of Annex E or on
small parts of material classified as V-0 or V-1
according to IEC 60695-11-10
Test as specified for an interposed shielding material N
30.2.3.2 Parts of non-metallic material supporting current- P
carrying connections, and
parts of non-metallic material within a distance of P
3mm,
subjected to glow-wire test of IEC 60695-2-11 P
Test not carried out on material having a glow-wire N
ignition temperature according to IEC 60695-2-13 of
at least:
-775°C, for connections carrying a current exceeding N
0,2A during normal operation
-675°C, for other connections N
When the glow-wire test of IEC 60695-2-11 is carried out, the temperatures are: -
-750°C, for connections carrying a current exceeding P
0,2A during normal operation
-650°C, for other connections N
Parts that during the test produce a flame persisting N
longer than 2 s, tested as specified
If a flame persists longer than 2 s during the test, N
parts above the connection, as specified, subjected
to the needle-flame test of annex E, unless
the material is classified as V-0 or V-1 according to N
IEC 60695-11-10
30.2.4 Base material of printed circuit boards subjected to N
needle-flame test of annex E
Test not applicable to conditions as specified N

31 RESISTANCE TO RUSTING -

Accredited Testing Laboratory

 Page 65 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

Relevant ferrous parts adequately protected against P

rusting

32 RADIATION, TOXICITY AND SIMILAR HAZARDS -

Appliance shall not emit harmful radiation, present a P
toxic or similar hazard due to their operation in
normal use
Relevant tests specified in part 2, if necessary P
32.101 Pyrolytic self-cleaning ovens shall be constructed N
so that the carbon monoxide is not discharged in
hazardous quantities during cleaning
(IEC 60335-2-6:2002)

A ANNEX A (INFORMATIVE) -
ROUTINE TESTS
Description of routine tests to be carried out by the P
manufacturer

B ANNEX B (NORMATIVE) -
APPLIANCES POWERED BY RECHARGEABLE BATTERIES
The following modifications to this standard are N
applicable for appliances powered by batteries that
are recharged in the appliance
This annex does not apply to battery chargers N
3.1.9 Appliance operated under the following conditions:
-the appliance, supplied by its fully charged battery, N
operated as specified in relevant part 2
-the battery is charged, the battery being initially N
discharged to such an extent that the appliance
cannot operate
-if possible, the appliance is supplied from the supply N
mains through its battery charger, the battery being
initially discharged to such an extent that the
appliance cannot operate. The appliance is operated
as specified in relevant part 2

Accredited Testing Laboratory

 Page 66 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

If the appliance incorporates inductive coupling N

between two parts that are detachable from each
other, the appliance is supplied from the supply
mains with the detachable part removed
3.6.2 Part to be removed in order to discard the battery is N
not considered to be detachable
5.101 Appliances supplied from the supply mains tested as N
specified for motor-operated appliances
7.1 Battery compartment for batteries intended to be N
replaced by the user, marked with battery voltage
and polarity of the terminals
7.12 The instructions for appliances incorporating N
batteries intended to be replaced by the user includes
required information
Details about how to remove batteries containing N
materials hazardous to the environment given
7.15 Markings placed on the part of the appliance N
connected to the supply mains
8.2 Appliances having batteries that according to the N
instruction may be replaced by the user need only
have basic insulation between live parts and the inner
surface of the battery compartment
If the appliance can be operated without batteries, N
double or reinforced insulation required
11.7 The battery is charged for the period described N
19.1 Appliances subjected to tests of 19.101, 19.102 and N
19.103
19.101 Appliances supplied at rated voltage for 168 h, the N
battery being continually charged
19.102 Short-circuiting of the terminals of the battery, being N
fully charged, for appliances having batteries that can
be removed without the aid of a tool
19.103 Appliances having batteries replaceable by the user N
supplied at rated voltage under normal operation with
the battery removed or in any position allowed by the
construction

Accredited Testing Laboratory

 Page 67 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

21.101 Appliances having pins for insertion into socket- N

outlets have adequate mechanical strength, checked
according to procedure 2 of IEC 68-2-32
Part of the appliance incorporating the pins subjected to the free fall test, procedure 2, -
of IEC 60068-2-32, the number of falls being:
- 100, the mass of part does not exceed 250 g N
- 50, the mass of part exceeds 250 g N
After the test, the requirements of 8.1, 15.1.1, 16.3 N
and clause 29 are met
22.3 Appliances having pins for insertion into socket- N
outlets tested as fully assembled as possible
25.13 An additional lining or bushing not required for N
interconnection cords operating at safety extra-low
voltage
30.2 For parts of the appliance connected to the supply N
mains during the charging period, 30.2.3 applies
For other parts, 30.2.2 applies N

C ANNEX C (NORMATIVE) -
AGEING TEST ON MOTORS
Tests, as described, carried out when doubt with N
regard to the temperature classification of the
insulation of a motor winding

D ANNEX D (NORMATIVE) -
THERMAL MOTOR PROTECTORS
Applicable to appliances having motors that N
incorporate thermal motor protectors

E ANNEX E (NORMATIVE) -
NEEDLE-FLAME TEST
Needle-flame test carried out in accordance with P
IEC 60695-11-5, with the following modifications:
7 Severities -

Accredited Testing Laboratory

 Page 68 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

The duration of application of the test flame is N

30 s ± 1 s
9 Test procedure -
9.1 The specimen so arranged that the flame can be N
applied to a vertical or horizontal edge as shown in
the examples of figure 1
9.2 The first paragraph does not apply N
If possible, the flame is applied at least 10 mm from a N
corner
9.3 The test is carried out on one specimen N
If the specimen does not withstand the test, the test N
may be repeated on two additional specimens, both
withstanding the test
10 Evaluation of test results -
The duration of burning not exceeding 30 s N
However, for printed circuit boards, the duration of N
burning not exceeding 15 s

F ANNEX F (NORMATIVE) -
CAPACITORS
Capacitors likely to be permanently subjected to the N
supply voltage, and used for radio interference
suppression or voltage dividing, comply with the
following clauses of IEC 60384-14, with the following
modifications:
1.5 Terminology -
1.5.3 Class X capacitors tested according to subclass X2 N
1.5.4 This subclause is applicable N
1.6 Marking -
Items a) and b) are applicable N
3.4 Approval testing -
3.4.3.2 Table II is applicable as described N
4.1 Visual examination and check of dimensions -

Accredited Testing Laboratory

 Page 69 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

This subclause is applicable N

4.2 Electrical tests -
4.2.1 This subclause is applicable N
4.2.5 This subclause is applicable N
4.2.5.2 Only table IX is applicable N
Values for test A apply N
However, for capacitors in heating appliances the N
values for test B or C apply
4.12 Damp heat, steady state -
This subclause is applicable N
Only insulation resistance and voltage proof are N
checked
4.13 Impulse voltage -
This subclause is applicable N
4.14 Endurance -
Subclauses 4.14.1, 4.14.3, 4.14.4 and 4.14.7 N
applicable
4.14.7 Only insulation resistance and voltage proof are N
checked
Visual examination, no visible damage N
4.17 Passive flammability test -
This subclause is applicable N
4.18 Active flammability test -
This subclause is applicable N

G ANNEX G (NORMATIVE) -
SAFETY ISOLATING TRANSFORMERS
The following modifications to this standard are N
applicable for safety isolating transformers:
7 Marking and instructions -
7.1 Transformers for specific use marked with: -

Accredited Testing Laboratory

 Page 70 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

-name, trademark or identification mark of the N

manufacturer or responsible vendor
-model or type reference N
17 Overload protection of transformers and associated circuits -
Fail-safe transformers comply with subclause 15.5 of N
IEC 61558-1
22 Construction -
Subclauses 19.1 and 19.1.2 of IEC 61558-2-6 are N
applicable
29 Clearances, creepage distances and solid insulation -
29.1, 29.2 The distances specified in items 2a, 2c and 3 in table N
and 29.3 13 of IEC 61558-1 apply

H ANNEX H (NORMATIVE) -
SWITCHES
Switches comply with the following clauses of IEC 61058-1, as modified: -
-The tests of IEC 61058-1 carried out under the N
conditions occurring in the appliance
-Before being tested, switches are operated 20 times N
without load
8 Marking and documentation -
Switches are not required to be marked N
However, switches that can be tested separately N
from the appliance marked with the manufacturer’s
name or trade mark and the type reference
13 Mechanism -
The tests may be carried out on a separate sample N
15 Insulation resistance and dielectric strength -
15.1 Not applicable N
15.2 Not applicable N
15.3 Applicable for full disconnection and micro- N
disconnection

Accredited Testing Laboratory

 Page 71 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

17 Endurance -
Compliance is checked on three separate appliances N
or switches
For 17.2.4.4, the number of cycles is 10 000, unless N
otherwise specified in 24.1.3 of the relevant part 2 of
IEC 60335
Switches for operation under no load and which can N
be operated only by a tool and switches operated by
hand that are interlocked so that they cannot be
operated under load, are not subjected to the tests
Subclauses 17.2.2 and 17.2.5.2 not applicable N
The ambient temperature during the test is that N
occurring in the appliance during the test of Clause
11 in IEC 60335-1
Temperature rise of the terminals not more than 30 K N
above the temperature rise measured in clause 11 of
IEC 60335-1
20 Clearances, creepage distances, solid insulation and coatings of rigid printed board -
assemblies
This clause is applicable to clearances and creepage N
distances for functional insulation, across full
disconnection and micro-disconnection, as stated in
table 24

I ANNEX I (NORMATIVE) -
MOTORS HAVING BASIC INSULATION THAT IS INADEQUATE FOR THE RATED
VOLTAGE OF THE APPLIANCE
The following modifications to this standard are N
applicable for motors having basic insulation that is
inadequate for the rated voltage of the appliance:
8 Protection against access to live parts -
8.1 Metal parts of the motor are considered to be bare N
live parts
11 Heating -

Accredited Testing Laboratory

 Page 72 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

11.3 Temperature rise of the body of the motor is N

determined instead of the temperature rise of the
windings
11.8 Temperature rise of the body of the motor, where in N
contact with insulating material, not exceeding values
in table 3 for the relevant insulating material
16 Leakage current and electric strength -
16.3 Insulation between live parts of the motor and its N
other metal parts not subjected to the test
19 Abnormal operation -
19.1 The tests of 19.7 to 19.9 not carried out N
19.101 Appliance operated at rated voltage with each of the following fault conditions: -
- short circuit of the terminals of the motor, including N
any capacitor incorporated in the motor circuit
- short circuit of each diode of the rectifier N
- open circuit of the supply to the motor N
- open circuit of any parallel resistor, the motor being N
in operation
Only one fault simulated at a time, the tests carried N
out consecutively
22 Construction -
22.101 For class I appliances incorporating a motor supplied N
by a rectifier circuit, the d.c. circuit being insulated
from accessible parts of the appliance by double or
reinforced insulation
Compliance checked by the tests specified for double N
and reinforced insulation

J ANNEX J (NORMATIVE) -
COATED PRINTED CIRCUIT BOARDS
Testing of protective coatings of printed circuit boards N
carried out in accordance with IEC 60664-3 with the
following modifications:
5.7 Conditioning of the test specimens -

Accredited Testing Laboratory

 Page 73 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

When production samples are used, three samples N

of the printed circuit board are tested
5.7.1 Cold -
The test is carried out at -25°C N
5.7.3 Rapid change of temperature -
Severity 1 is specified N
5.9 Additional tests -
This subclause is not applicable N

K ANNEX K (NORMATIVE) -
OVERVOLTAGE CATEGORIES
The information on overvoltage categories is P
extracted from IEC 60664-1
Overvoltage category is a numeral defining a P
transient overvoltage condition
Equipment of overvoltage category IV is for use at N
the origin of the installation
Equipment of overvoltage category III is equipment in N
fixed installations and for cases where the reliability
and the availability of the equipment is subject to
special requirements
Equipment of overvoltage category II is energy P
consuming equipment to be supplied from the fixed
installation
If such equipment is subjected to special N
requirements with regard to reliability and availability,
overvoltage category III applies
Equipment of overvoltage category I is equipment for N
connection to circuits in which measures are taken to
limit transient overvoltages to an appropriate low level

L ANNEX L (INFORMATIVE) -
GUIDANCE FOR THE MEASUREMENT OF CLEARANCES AND CREEPAGE
DISTANCES

Accredited Testing Laboratory

 Page 74 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

Sequences for the determination of clearances and P

creepage distances

M ANNEX M (NORMATIVE) -
POLLUTION DEGREE
The information on pollution degrees is extracted P
from IEC 60664-1
Pollution -
The microenvironment determines the effect of N
pollution on the insulation, taking into account the
microenvironment
Means may be provided to reduce pollution at the N
insulation by effective enclosures or similar
Minimum clearances specified where pollution may N
be present in the microenvironment
Degrees of pollution in the microenvironment -
For evaluating creepage distances, the following degrees of pollution in the -
microenvironment are established:
- pollution degree 1: no pollution or only dry, non- N
conductive pollution occurs. The pollution has no
influence
- pollution degree 2: only non-conductive pollution N
occurs, except that occasionally a temporary
conductivity caused by condensation is to be
expected
- pollution degree 3: conductive pollution occurs or P
dry non-conductive pollution occurs that becomes
conductive due to condensation that is to be
expected
- pollution degree 4: the pollution generates N
persistent conductivity caused by conductive dust or
by rain or snow

N ANNEX N (NORMATIVE) -
PROOF TRACKING TEST

Accredited Testing Laboratory

 Page 75 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

The proof tracking test is carried out in accordance N

with IEC 60112 with the following modifications:
7 Test apparatus -
7.3 Test solutions -
Test solution A is used N
10 Determination of proof tracking index (PTI) -
10.1 Procedure -
The proof voltage is 100V, 250V, 175V, 400V or N
600V..........................................................................:
The last paragraph of Clause 3 applies N
The test is carried out on five specimens N
In case of doubt, additional test with proof voltage N
reduced by 25V, the number of drops increased to
100
10.2 Report -
The report stating if the PTI value was based on a N
test using 100 drops with a test voltage of (PTI-25) V

O ANNEX O (INFORMATIVE) -
SELECTION AND SEQUENCE OF THE TESTS OF CLAUSE 30
Description of tests for determination of resistance to P
heat and fire

P ANNEX P (INFORMATIVE) -
GUIDANCE FOR THE APPLICATION OF THIS STANDARD TO APPLIANCES
USED IN WARM DAMP EQUABLE CLIMATES
Modifications applicable for class 0 and 01 appliances having a rated voltage -
exceeding 150V, intended to be used in countries having a warm damp equable
climate and that are marked WDaE
Modifications may also be applied to class 1 appliances having a rated voltage -
exceeding 150V, intended to be used in countries having a warm damp equable
climate and that are marked WdaE, if liable to be connected to a supply mains that
excludes the protective earthing conductor
5 General conditions for the tests -

Accredited Testing Laboratory

 Page 76 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

5.7 The ambient temperature for the tests of Clauses 11 N

+3
and 13 is 40 /0
7 Marking and instructions -
7.1 The appliance marked with the letters WDaE N
7.12 The instructions state that the appliance is to be N
supplied through a RCD having a rated residual
operating current not exceeding 30 mA
The instructions state that the appliance is N
considered to be suitable for use in countries having
a warm damp equable climate, but may also be used
in other countries
11 Heating -
11.8 The values of Table 3 are reduced by 15 K N
13 Leakage current and electric strength at operating temperature -
13.2 The leakage current for class I appliances not N
exceeding 0,5 mA
15 Moisture resistance -
15.3 The value of t is 37 °C N
16 Leakage current and electric strength -
16.2 The leakage current for class I appliances not N
exceeding 0,5 mA
19 Abnormal operation -
19.13 The leakage current test of 16.2 is applied in addition N
to the electric strength test of 16.3

Q ANNEX Q (INFORMATIVE) -
SEQUENCE OF TESTS FOR THE EVALUATION OF ELECTRONIC CIRCUITS
Description of tests for appliances incorporating electronic circuits N

R ANNEX R (NORMATIVE) -
SOFTWARE EVALUATION
Software evaluated in accordance with the following clauses of Annex H of IEC 60730- N
1, as modified

Accredited Testing Laboratory

 Page 77 of 120

Order No. 198155TRFSAF

IEC 60335-2-6
Clause Requirement + Test Result - Remark Verdict

H.2 Definitions -
Only definitions H.2.16 to H.2.20 applicable N
H.7 Information -
Only footnotes 12) to 18) of Table 7.2, as modified, N
applicable
H.11.12 Controls using software -
All the subclauses of H.11.12, as modified, except N
H.11.12.6 and H.11.12.6.1, applicable
H.11.12.7 Delete text N
H.11.12.7.1 For appliances using software class C having a N
single channel with self-test and monitoring structure,
the manufacturer provides the measures necessary
to address the fault/errors in safety related segments
and data
H.11.12.8 Software fault/error detection occurs before N
compliance with 19.13 of IEC 60335-1 is impaired
H.11.12.8.1 Replace text N
H.11.12.13 Software and safety related hardware under its N
control initializes and terminates before compliance
with 19.13 of IEC 60335-1 is impaired

Accredited Testing Laboratory

 Page 78 of 120

Order No. 198155TRFSAF

IEC 60335-2-6

10.1 TABLE: Power input deviation P

Input deviation of/at: P rated (W) P measured dP Required dP Remark
(W)
at 230V 3500 3660 +4.6% -10% / + 5%

~
10.2 TABLE: Current deviation P
Current deviation of/at: I rated (A) I measured (A) dI Required dI Remark
at 230V 15.2 15.9

11.7 TABLE: heating temperature specifications P

test step n°/ function temperature duration
1 - hobs ON Water 100°C 60

Accredited Testing Laboratory

 Page 79 of 120

Order No. 198155TRFSAF

IEC 60335-2-6

11.8 TABLE: Heating test, thermocouples P

hobs function
Test voltage (V) ........................................................: 1.15x3500Wx(240/230)² = 
4383W (247V)
Ambient (°C) .............................................................: 25 
Thermocouple locations dT (K) Max. dT (K)
Ignition transformer T120 24 95
Hob Switch T125 23 100
Internal wiring T180 61 155
Signal lamp T120 46 95
Internal cable near heating element T180 89 155
Main terminal block T125 38 100
Terminal block cover 26 Crf.cl.30
Test corner (side position (right) 22 70

Test corner (back position) 47 70

Test corner (bottom position) 15 70

11.8 TABLE: Heating test, resistance method N

Test voltage (V) ........................................................: 
Ambient, t1 (°C) .........................................................: 
Ambient, t2 (°C) .........................................................: 
Temperature rise of winding R1 (Ω) R2 (Ω) dT (K) Max. dT (K) Insulation
class

11.101 TABLE: Temperature rise limits for accessible surfaces specifications P

test step n°/ function temperature duration
With hobs - 60

Accredited Testing Laboratory

 Page 80 of 120

Order No. 198155TRFSAF

IEC 60335-2-6

11.101 TABLE: Temperature rise limits for accessible front and side surfaces P
dT (K) Max. dT (K)
Front surfaces of oven doors  
Test step n. - - - - - - 
Ambient (°C) - - - - - - 
Metal and painted metal - - - - - - 45
Vitreous-enamelled metal - - - - - - 50
Glass and ceramic - - - - - - 60
Plastic having a thickness exceeding 0,3mm - - - - - - 80
Other accessible front and side surfaces 
(or surfaces above 850 mm)
Test step n. 1 - - - - - 
Ambient (°C) 25 - - - - - 
Metal and painted metal 20 - - - - - 60
Vitreous-enamelled metal - - - - - - 65
Glass and ceramic - - - - - - 80
Plastic having a thickness exceeding 0,3mm 10 - - - - - 100

13.2 TABLE: Leakage current P

Heating appliances: 1.15 x rated input...................: 1.15x3580Wx(240/230)² = 
4483W (248V)
Motor-operated and combined appliances: - 
1.06 x rated voltage ................................................:
Leakage current between I (mA) Max. allowed I (mA)
Any pole of supply and accessible metal parts:(hobs) 0.03 3.5
Any pole and accessible parts (control panel) 0.03 0.25
Any pole and accessible parts (body) 0.03 0.25

Accredited Testing Laboratory

 Page 81 of 120

Order No. 198155TRFSAF

IEC 60335-2-6

13.3 TABLE: Electric strength N

Test voltage applied between: Voltage (V) Breakdown
(Yes/No)
Any pole of supply and accessible metal parts 1000 No
Any pole and accessible parts (knobs) 3000 No
Any pole and accessible parts (spark ignition tip) 3000 No

14 TABLE: Transient overvoltages N

Clearance between: Cl (mm) Required Rated impulse Impulse test Flashover
Cl (mm) voltage (V) voltage (V) (Yes/No)

16.2 TABLE: Leakage current P

Single phase appliances: 1.06 x rated voltage ......: 254.4V 
Three phase appliances 1.06 x rated voltage - 
divided by √3:..........................................................:
Leakage current between I (mA) Max. allowed I (mA)
Any pole of supply and accessible metal parts: 0.04 3.5
Any pole and accessible parts (control panel) 0.04 0.25
Any pole and accessible parts (body) 0.04 0.25

Accredited Testing Laboratory

 Page 82 of 120

Order No. 198155TRFSAF

IEC 60335-2-6

16.3 TABLE: Electric strength P

Test voltage applied between: Voltage (V) Breakdown
(Yes/No)
Any pole of supply and accessible metal parts 1250 No
Any pole and accessible parts (knobs) 3000 No
Any pole and accessible parts (spark ignition tip) 3000 No

17 TABLE: Overload protection, temperature rise N

Temperature rise of part/at: dT (K) Max. dT (K)

19 TABLE: abnormal operation specifications P

test step
Clause n. Function temperature duration 
19.2 1 with hobs function Max 60 minutes
19.3 2 with hobs function Max 60 minutes
19.4 3 with hobs function Max 60 minutes
19.5 4 with hobs function Max 60 minutes

19.7 TABLE: Abnormal operation, locked rotor/moving parts N

Test voltage (V)........................................................ : 
Ambient, t1 (°C) ........................................................ : 
Ambient, t2 (°C) ........................................................ : 
Temperature of winding R1 (Ω) R2 (Ω) dT (K) T (°C) Max. T (°C)

Accredited Testing Laboratory

 Page 83 of 120

Order No. 198155TRFSAF

IEC 60335-2-6

19.7 and TABLE: abnormal operation, temperature and temperature rise measurements P
19.13
at 0,85 times rated for test step n.: 1 (19.2) heating hob 
at 1,15 times rated for test step n.: 2 (19.4) heating hob 
3 (19.5) heating hob
at 1,24 times rated for test step n.: 4 (19.3) heating hob
at voltage input (V) for test step n.: 
Part measured Max. dT (K) Measured (K)
Test step n. --- 1 2 3 4
Ambient (°C) 25 25 25 25
Wall-ceiling and floor of test corner 150 67 116 67 93
Terminal block 150 43 91 49 60
Power cord 150 17 27 14 22

Thermoplastic material parts used as:

- supplementary insulation
- reinforced insulation

Maximum winding temperature of: (°C)

Part measured Max. dT (K) Measured (K)
Test step n. ---
Ambient (°C)
Wall-ceiling and floor of test corner 150
Supply cable of cord insulation 150
Thermoplastic material parts used as:
- supplementary insulation
- reinforced insulation
Maximum winding temperature of: (°C)

Accredited Testing Laboratory

 Page 84 of 120

Order No. 198155TRFSAF

IEC 60335-2-6

24.1 TABLE: Components P

Manufacturer/ Mark(s) of
Object / part No. Type / model Technical data Standard
trademark conformity
Terminal block NOVA SL100 16A 400 V T125 EN 60998-1 VDE
Terminal block
GP BGTB16A 450V, 16A, T110 EN 60335-2-6 CTS
(alternative)
Tested in
Signal Lamp AR-EL SL-400 250V AC T120 EN 60335-2-6
appliance VDE
Signal Lamp S01-S10-S16- Tested in
AN-EL 240V AC T120 EN 60335-2-6
(alternative) S13-S19-S20 appliance VDE
Signal Lamp
Başoğlu HB9 240V AC T120 EN 60335-2-6 VDE
(alternative)
EN 60335-2-6 EN Test in the
Internal wiring STAR N2GFAF 300V, T180
60335-1 appliance, VDE
Internal wiring EN 60335-2-6 EN Test in the
ELCAB N2GFAF 300V, T180
(alternative) 60335-1 appliance, VDE
Hob heating 22375315072 2000W Test in the
ŞANAL EN 60335-2-6
element 111 230V appliance TUV
Hob heating 135W – 1500W
PĐRAMĐT 41* EN 60335-2-6 VDE
element(alternative) 100V - 240V
Hob heating HP180R-4
HOTDAC 2000W 230V EN 60335-2-6 NEMKO
element(alternative)
Hob heating GP.180.20.4.
GP 2000W 230V EN 60335-2-6 VDE
element(alternative) RH
Hob heating 22275315051 1500W Tested in
ŞANAL EN 60335-2-6
element 111 230V appliance TUV
Hob heating
HOTDAC HP145R-4 230V 1500W EN 60335-2-6 NEMKO
element(alternative)
Hob heating GP145.15.4.R
GP 230V 1500W EN 60335-2-6 VDE
element(alternative) H
Hob switch AN-EL RTH-D01 16A 250V T125 EN 61058-1 VDE
Hob switch
TIBON 430 250V T125 16A EN 61058-1 KEMA
(alternative)
Hob switch 230V/400V
MXT BC3 EN 61058-1 KEMA
(alternative) 10A/16A T150
Plug GMS G-20 16A 250V 2P+ IEC 60884 VDE
Plug (alternative) AREL 2002 16A 250V 2P+PE IEC 60884 KEMA

Accredited Testing Laboratory

 Page 85 of 120

Order No. 198155TRFSAF

IEC 60335-2-6

Plug (alternative) Deka 2PE02 16A 250V 2P+PE IEC 60884 VDE
Plug (alternative) Hedef TP501 16A 250V 2P+PE IEC 60884 VDE
Power cord GMS H05VV-F 3x1.5mm HD21 HAR
Power cord
Hedef H05VV-F 3x1.5mm HD21 HAR
(alternative)
220\240V 50-
Ignition device Erta ECB10-295 EN 61058 VDE
60Hz T120
Ignition device 220\240V 50-
GP 1814310 EN 61058 VDE
(Alternative) 60Hz T120
Ignition device 220\240V 50 EN 61058
Termal 507.XXX VDE
(Alternative) 60Hz
Ignition device 220\240V 50 EN 61058
Yangzhou DST2010-X.. VDE
(Alternative) 60Hz
Ignition device 220\240V 50 EN 61058
Castfatura IGB.... , IGS... VDE
(Alternative) 60Hz

29.1 TABLE: Clearances P

Overvoltage category ... : II 
Type of insulation:
Rated impulse Min. cl Basic Functional Supplementary Reinforced Verdict / Remark
voltage (V): (mm)
330 0,5*
500 0,5*
800 0,5*
1 500 0,5*/**
2 500 1,5** 3.4 mm 4.3 mm P
4 000 3,0** 7.0 mm P
6 000 5,5**
8 000 8,0**
10 000 11,0**
*) The value is increased to 0,8mm for pollution degree 3
*) If the construction is affected by wear, distortion, movement of the parts or during assembly, the value is
increased by 0,5 mm

Accredited Testing Laboratory

 Page 86 of 120

Order No. 198155TRFSAF

IEC 60335-2-6

29.2 TABLE: Creepage distances, basic, supplementary and reinforced insulation P

Working voltage Creepage distance (mm)
(V) Pollution degree
1 2 3 Type of insulation
Material group Material group
) ) )
I II IIIa/IIIb I II IIIa/IIIb B* S* R* Verdict
≤50 0,2 0,6 0,9 1,2 1,5 1,7 1,9  
≤50 0,2 0,6 0,9 1,2 1,5 1,7 1,9  
≤50 0,4 1,2 1,8 2,4 3,0 3,4 3,8  
>50 and ≤125 0,3 0,8 1,1 1,5 1,9 2,1 2,4  
>50 and ≤125 0,3 0,8 1,1 1,5 1,9 2,1 2,4  
>50 and ≤125 0,6 1,6 2,2 3,0 3,8 4,2 4,8  
>125 and ≤250 0,6 1,3 1,8 2,5 3,2 3,6 4.0 7.4  7.0 P
>125 and ≤250 0,6 1,3 1,8 2,5 3,2 3,6 4.0   
>125 and ≤250 1,2 2,6 3,6 5,0 6,4 7,2 8.0   
>250 and ≤400 1,0 2,0 2,8 4,0 5,0 5,6 6,3  
>250 and ≤400 1,0 2,0 2,8 4,0 5,0 5,6 6,3  
>250 and ≤400 2,0 4,0 5,6 8,0 10,0 11,2 12,6  
>400 and ≤500 1,3 2,5 3,6 5,0 6,3 7,1 8,0  
>400 and ≤500 1,3 2,5 3,6 5,0 6,3 7,1 8,0  
>400 and ≤500 2,6 5,0 7,2 10,0 12,6 14,2 16,0  
>500 and ≤800 1,8 3,2 4,5 6,3 8,0 9,0 10,0  
>500 and ≤800 1,8 3,2 4,5 6,3 8,0 9,0 10,0  
>500 and ≤800 3,6 6,4 9,0 12,6 16,0 18,0 20,0  
>800 and ≤1000 2,4 4,0 5,6 8,0 10,0 11,0 12,5  
>800 and ≤1000 2,4 4,0 5,6 8,0 10,0 11,0 12,5  
>800 and ≤1000 4,8 8,0 11,2 16,0 20,0 22,0 25,0  
>1000 and ≤1250 3,2 5,0 7,1 10,0 12,5 14,0 16,0  
>1000 and ≤1250 3,2 5,0 7,1 10,0 12,5 14,0 16,0  
>1000 and ≤1250 6,4 10,0 14,2 20,0 25,0 28,0 32,0  

Accredited Testing Laboratory

 Page 87 of 120

Order No. 198155TRFSAF

IEC 60335-2-6

>1250 and ≤1600 4,2 6,3 9,0 12,5 16,0 18,0 20,0  
>1250 and ≤1600 4,2 6,3 9,0 12,5 16,0 18,0 20,0  
>1250 and ≤1600 8,4 12,6 18,0 25,0 32,0 36,0 40,0  
>1600 and ≤2000 5,6 8,0 11,0 16,0 20,0 22,0 25,0  
>1600 and ≤2000 5,6 8,0 11,0 16,0 20,0 22,0 25,0  
>1600 and ≤2000 11,2 16,0 22,0 32,0 40,0 44,0 50,0  
>2000 and ≤2500 7,5 10,0 14,0 20,0 25, 0 28,0 32,0  
>2000 and ≤2500 7,5 10,0 14,0 20,0 25, 0 28,0 32,0  
>2000 and ≤2500 15,0 20,0 28,0 40,0 50,0 56,0 64,0  
>2500 and ≤3200 10,0 12,5 18,0 25,0 32,0 36,0 40,0  
>2500 and ≤3200 10,0 12,5 18,0 25,0 32,0 36,0 40,0  
>2500 and ≤3200 20,0 25,0 36,0 50,0 64,0 72,0 80,0  
>3200 and ≤4000 12,5 16,0 22,0 32,0 40,0 45,0 50,0  
>3200 and ≤4000 12,5 16,0 22,0 32,0 40,0 45,0 50,0  
>3200 and ≤4000 25,0 32,0 44,0 64,0 80,0 90,0 100,0  
>4000 and ≤5000 16,0 20,0 28,0 40,0 50,0 56,0 63,0  
>4000 and ≤5000 16,0 20,0 28,0 40,0 50,0 56,0 63,0  
>4000 and ≤5000 32,0 40,0 56,0 80,0 100,0 112,0 126,0  
>5000 and ≤6300 20,0 25,0 36,0 50,0 63,0 71,0 80,0  
>5000 and ≤6300 20,0 25,0 36,0 50,0 63,0 71,0 80,0  
>5000 and ≤6300 40,0 50,0 72,0 100,0 126,0 142,0 160,0  
>6300 and ≤8000 25,0 32,0 45,0 63,0 80,0 90,0 100,0  
>6300 and ≤8000 25,0 32,0 45,0 63,0 80,0 90,0 100,0  
>6300 and ≤8000 50,0 64,0 90,0 126,0 160,0 180,0 200,0  
>8000 and ≤10000 32,0 40,0 56,0 80,0 100,0 110,0 125,0  
>8000 and ≤10000 32,0 40,0 56,0 80,0 100,0 110,0 125,0  
>8000 and ≤10000 64,0 80,0 112,0 160,0 200,0 220,0 250,0  
>10000 and ≤12500 40,0 50,0 71,0 100,0 125,0 140,0 160,0  
>10000 and ≤12500 40,0 50,0 71,0 100,0 125,0 140,0 160,0  
>10000 and ≤12500 80,0 100,0 142,0 200,0 250,0 280,0 320,0  
)
* , B=Basic, S=Supplementary and R=Reinforced

Accredited Testing Laboratory

 Page 88 of 120

Order No. 198155TRFSAF

IEC 60335-2-6

29.2 TABLE: Creepage distances, functional insulation P

Creepage distance
(mm)
Pollution degree
Working voltage
(V)
1 2 3
Material group Material group
I II IIIa/IIIb I II IIIa/IIIb Verdict / Remark
≤50 0,2 0,6 0,8 1,1 1,4 1,6 1,8
>50 and ≤125 0,3 0,7 1,0 1,4 1,8 2,0 2,2
>125 and ≤250 0,4 1,0 1,4 2,0 2,5 2,8 3.2 P (7.0 mm)
>250 and ≤400 0,8 1,6 2,2 3,2 4,0 4,5 5,0
>400 and ≤500 1,0 2,0 2,8 4,0 5,0 5,6 6,3
>500 and ≤800 1,8 3,2 4,5 6,3 8,0 9,0 10,0
>800 and ≤1000 2,4 4,0 5,6 8,0 10,0 11,0 12,5
>1000 and ≤1250 3,2 5,0 7,1 10,0 12,5 14,0 16,0
>1250 and ≤1600 4,2 6,3 9,0 12,5 16,0 18,0 20,0
>1600 and ≤2000 5,6 8,0 11,0 16,0 20,0 22,0 25,0
>2000 and ≤2500 7,5 10,0 14,0 20,0 25,0 28,0 32,0
>2500 and ≤3200 10,0 12,5 18,0 25,0 32,0 36,0 40,0
>3200 and ≤4000 12,5 16,0 22,0 32,0 40,0 45,0 50,0
>4000 and ≤5000 16,0 20,0 28,0 40,0 50,0 56,0 63,0
>5000 and ≤6300 20,0 25,0 36,0 50,0 63,0 71,0 80,0
>6300 and ≤8000 25,0 32,0 45,0 63,0 80,0 90,0 100,0
>8000 and ≤10000 32,0 40,0 56,0 80,0 100,0 110,0 125,0
>10000 and ≤12500 40,0 50,0 71,0 100,0 125,0 140,0 160,0

Accredited Testing Laboratory

 Page 89 of 120

Order No. 198155TRFSAF

IEC 60335-2-6

TABLE 30 RENSISTANCE TO HEAT, FIRE AND TRACKING (appended table)

Component Manufacturer Type Ball pressure test Tracking Glow wire test Needle- Verdict
test flame
[CTI/ PTI] test
75°C cl. 11 125°C cl. 19 GWT GWT GWT GWFI GWIT
+40°C +25°C 550°C 650°C 750°C 850°C
Terminal Block NOVA SL1OO 0.3mm X X P
Terminal block cover NOVA SL1OO 1.0mm X P
Hob switch AN-EL RTH-D01 0.3mm X X P
Signal lamp AR-EL SL-400 0.4 mm X X P
ECB10- 0.3 mm P
Ignition device ERTA
295

Accredited Testing Laboratory

 Page 90 of 120

Order No. 198155TRFSAF

IEC60335_2_102B - ATTACHMENT
Clause Requirement + Test Result - Remark Verdict

Annex 1 to TEST REPORT

IEC 60335-2-102
Safety of household and similar electrical appliances
Part 2: Particular requirements for gas, oil and solid-fuel burning
appliances having electrical connections
Test item description ..................... : Built in hobs
Trade Mark ....................................... : PLASFORM - VĐNOLA
Manufacturer .................................... : PLASFORM PLASTĐK VE METAL END.A.Ş

Factory…………………………………: PLASFORM PLASTĐK VE METAL END.A.Ş

Model/Type reference....................... :
Ratings ............................................. : 3500 W 220-240V~ 50 Hz

Accredited Testing Laboratory

 Page 91 of 120

Order No. 198155TRFSAF

IEC60335_2_102B - ATTACHMENT
Clause Requirement + Test Result - Remark Verdict

5 GENERAL CONDITIONS FOR THE TESTS -

Tests performed according to cl. 5, e.g. nature of P
supply, sequence of testing, etc.
5.2 A separate appliance may be used for the test N
carried out on the fuel-burning appliance, in
accordance with relevant standard.
( IEC 60335-2-102)
The test of this standard may be carried out in N
conjunction with the tests of another part 2, if
applicable. ( IEC 60335-2-102)
5.3 If a test has carried out in accordance with the fuel- N
burning appliance standard, it is not repeated
( IEC 60335-2-102)
5.4 When the appliance incorporates electric heating P
sources, the tests are carried out with all parts of the
appliance in operation, as allowed by the
construction (IEC 60335-2-102)

8 PROTECTION AGAINST ACCESS TO LIVE PARTS -

8.1 Adequate protection against accidental contact with P
live parts
The requirement does not apply to accessible parts P
of spark-ignition circuits (IEC 60335-2-102)
8.1.1 Requirement applies for all positions, detachable P
parts removed
Insertion or removal of lamps, protection against N
contact with live parts of the lamp cap
Use of test probe B of IEC 61032: no contact with P
live parts
8.1.2 Use of test probe 13 of IEC 61032 through openings N
in class 0 appliances and class II appliances/
constructions: no contact with live parts
Test probe 13 also applied through openings in N
earthed metal enclosures having a non-conductive
coating: no contact with live parts

Accredited Testing Laboratory

 Page 92 of 120

Order No. 198155TRFSAF

IEC60335_2_102B - ATTACHMENT
Clause Requirement + Test Result - Remark Verdict

8.1.3 For appliances other than class II, use of test probe N
41 of IEC 61032: no contact with live parts of visible
glowing heating elements
8.1.4 Accessible part not considered live if: -
- safety extra-low a.c. voltage: peak value not N
exceeding 42.4 V
- safety extra-low d.c. voltage: not exceeding 42.4 V N
- or separated from live parts by protective N
impedance
If protective impedance: d.c. current not exceeding N
2 mA, and
a.c. peak value not exceeding 0.7 mA N
- for peak values over 42.4 V up to and including N
450 V, capacitance not exceeding 0,1 µF
- for peak values over 450 V up to and including N
15 kV, discharge not exceeding 45 µC
- for peak values over 15kV, the energy in the N
discharge not exceeding 350 mJ
8.1.5 Live parts protected at least by basic insulation before installation or assembly: -
- built-in appliances P
- fixed appliances N
- appliances delivered in separate units N
8.2 Class II appliances and constructions constructed so N
that there is adequate protection against accidental
contact with basic insulation and metal parts
separated from live parts by basic insulation only
Only possible to touch parts separated from live N
parts by double or reinforced insulation
8.101 Parts of spark-ignition circuit shall not be P
accessible if the limits in table 101 are exceeded,
unless they are piezoelectric igniters.
(IEC 60335-2-102/A1)

11 HEATING -

Accredited Testing Laboratory

 Page 93 of 120

Order No. 198155TRFSAF

IEC60335_2_102B - ATTACHMENT
Clause Requirement + Test Result - Remark Verdict

11.8 Temperature rises not exceeding values in table 3 (see appended tables) P
Sealing compound does not flow out P
Protective devices do not operate, except P
components in protective electronic circuits tested for N
the number of cycles specified in 24.1.4
The temperature rise of the walls of test corner are N
not measured. (IEC 60335-2-102)
The temperature rise limits for common parts of N
appliance having electric and fuel-burning heating
source are specified in the relevant part 2.
(IEC 60335-2-102)

13 LEAKAGE CURRENT AND ELECTRIC STRENGTH AT OPERATING -

TEMPERATURE
For appliances which are assembled on site, the N
leakage current and electrical strength tests on the
complete appliance need not be performed if the
components and sub-assemblies have been
separately tested and the interconnection is carried
out in accordance with the manufacturers
Instructions . (IEC 60335-2-102)
If the disconnection of protective impedance or N
radio interference filters is not possible, the limit
specified for leakage currents is to be calculated
taking into account the current through those
circuits or components. (IEC 60335-2-102)

15 MOISTURE RESISTANCE -
15.2 Spillage of liquid does not affect the electrical P
insulation
Appliances with type X attachment fitted with a N
flexible cord as described
Appliances incorporating an appliance inlet tested N
with or without an connector, whichever is most
unfavourable
Detachable parts removed N
Overfilling test with additional amount of P
water, over a period of 1 min (l)................................:

Accredited Testing Laboratory

 Page 94 of 120

Order No. 198155TRFSAF

IEC60335_2_102B - ATTACHMENT
Clause Requirement + Test Result - Remark Verdict

The appliance withstands the electric strength test of P

16.3
No trace of water on insulation that can result in a P
reduction of clearances and creepage distances
below values specified in clause 29
Tests on cooking ranges, hobs and similar P
appliances (IEC 60335-2-102)

16 LEAKAGE CURRENT AND ELECTRIC STRENGTH -

16.2 Single-phase appliances: test voltage 1.06 times P
peak voltage ( IEC 60335-2-102/A1)……………..:
Three-phase appliances: test voltage 1.06 times N
peak voltage divided by √3( IEC 60335-2-102/A1).:
Leakage current measurements (IEC 60335-2-102) (see appended table) P
No breakdown during the tests P
19 ABNORMAL OPERATION -
19.1 The risk of fire or mechanical damage under P
abnormal or careless operation obviated
Electronic circuits so designed and applied that a N
fault will not render the appliance unsafe
Appliances incorporating contactors or relays N
subjected to the test of 19.14, being carried out
before the tests of 19.11
19.2 Test of appliance with heating elements with P
restricted heat dissipation; test voltage (V): power
input of 0.85 times rated power input ...................... :
19.3 Test of 19.2 repeated; test voltage (V): power input P
of 1.24 times rated power input ............................... :
19.4 Test conditions as in cl. 11, any control limiting the N
temperature during tests of cl. 11 short-circuited
The test repeated with reversed polarity and the N
other end of the heating element connected to the
sheath (IEC 60335-2-102/A1)

Accredited Testing Laboratory

 Page 95 of 120

Order No. 198155TRFSAF

IEC60335_2_102B - ATTACHMENT
Clause Requirement + Test Result - Remark Verdict

The test is not carried out on appliances intended to N

be permanently connected to fixed wiring and on
appliances where an all-pole disconnection all fuels
valve . (IEC 60335-2-102/A1)
19.11.2 Fault conditions applied one at a time, the appliance operated under conditions
specified in cl. 11, but supplied at rated voltage, the duration of the tests as specified:

a) short circuit of functional insulation if clearances or N

creepage distances are less than the values
specified in 29
b) open circuit at the terminals of any component N
c) short circuit of capacitors, unless they comply with N
IEC 60384-14
d) short circuit of any two terminals of an electronic N
component, other than integrated circuits. This fault
condition is not applied between the two circuits of
an optocoupler
e) failure of triacs in the diode mode N
f) failure of an integrated circuit N
g) failure of an electronic power switching device N
For risk concerning the fuel , in each case the test is N
ended if a shut-down is performed.
(IEC 60335-2-102/A1)
19.11.4 Appliances having a device with an off position N
obtained by electronic disconnection, or
a device that can be placed in the stand-by mode, N
subjected to the tests of 19.11.4.1 to 19.11.4.7 N
Appliances incorporating a protective electronic N
circuit subjected to the tests of 19.11.4.1 to
19.11.4.7, except that
appliances operated for 30 s or 5 min during the test N
of 19.7 are not subjected to the tests for
electromagnetic phenomena.
The tests of 19.11.4.1 to 19.11.4.7 are also carried N
out under normal operation, the appliance being
supplied at rated voltage. (IEC 60335-2-102)

Accredited Testing Laboratory

 Page 96 of 120

Order No. 198155TRFSAF

IEC60335_2_102B - ATTACHMENT
Clause Requirement + Test Result - Remark Verdict

19.13 During the tests the appliance does not emit flames, P
molten metal, poisonous or ignitable gas in
hazardous amounts
Temperature rises not exceeding the values shown (see appended table) P
in table 9
Compliance with cl. 8 not impaired P
If the appliance can still be operated it complies with P
20.2
Insulation, other than of class III appliance, withstand the electric strength test of 16.3, -
the test voltage specified in table 4:
- basic insulation ...................................................... : 1000V P
- supplementary insulation ....................................... : N
- reinforced insulation............................................... : 3000V P
After operation or interruption of a control, N
clearances and creepage distances across the
functional insulation withstanding the electric
strength test of 16.3. the test voltage being twice the
working voltage
The appliance does not undergo a dangerous N
malfunction, and
no failure of protective electronic circuits, if the N
appliance is still operable
Appliances tested with an electronic switch in the off position, or in the stand-by
mode:
- do not become operational, or N
- if they become operational, do not result in a N
dangerous malfunction during or after the tests of
19.11.4
During the tests of 19.11.4, the appliance continue to N
operate normally (IEC 60335-2-102)
After the testes of 19.11.4 on gas and oil-burning N
appliances shall have reached a lock-out condition,
unless it continuous to operate normally.
(IEC 60335-2-102)

Accredited Testing Laboratory

 Page 97 of 120

Order No. 198155TRFSAF

IEC60335_2_102B - ATTACHMENT
Clause Requirement + Test Result - Remark Verdict

21 MECHANICAL STRENGTH -
21.1 Appliance has adequate mechanical strength and is P
constructed as to withstand rough handling
(IEC 60335-2-102)

22 CONSTRUCTION -
22.101 Parts of spark-ignition circuits shall be positioned or P
secured against loosening so that contact between
the circuit and other live parts is prevented.
(IEC/EN 60335-2-102)
22.102 If compliance with this standard can be affected by N
the polarity of the supply in the event of an earth
fault, the appliance shall incorporate a polarity-
detection device that results in shut-down or
prevents the appliance from operating if the polarity
is reversed. (IEC/EN 60335-2-102)
This requirement does not apply to appliances N
incorporating a control having all-pole
disconnection, to appliances intended to be
permanently connected to fixed wiring, or to
appliances having a supply cord fitted with a
polarized plug. (IEC/EN 60335-2-102)
22.103 If the limits in 8.101 are exceeded , the insulation of N
the parts of the circuit, where the distance to
unearthed accessible conductive parts do not
comply with reinforced insulation according to
29.1 and 29.2 (IEC/EN 60335-2-102/A1)
shall be resistant to ageing caused by partial N
discharge due to the ignition sparks .Unless the
insulation of cables having electrical properties
complying with ISO 3808
or the spark-ignition circuit are operated for at least N
100 h under the following test :
- Maximum duration of ignition switch-on repeated N
for the appropriate number of cycles in order to
obtained the total test time
- maximum value of the spark ignition voltage N
measured when the appliance is supplied at rated
voltage
- the temperature of the insulation as measured N
under conditions of Clause 11.
There shall be no breakdown of the insulation . N
In case of doubt the test of 16.3 is applied between
the cable conductor and water with cable insulation
immersed in water.

Accredited Testing Laboratory

 Page 98 of 120

Order No. 198155TRFSAF

IEC60335_2_102B - ATTACHMENT
Clause Requirement + Test Result - Remark Verdict

24 COMPONENTS -
24.101 Appliance outlets and plug connectors of N
interconnection cords shall not be
interchangeable if this could result in a hazard.
(IEC/EN 60335-2-102)

27 PROVISION FOR EARTHING -

27.1 Accessible metal parts of Class 0I and I appliances, N
permanently and reliably connected to an earthing
terminal or contact of the appliance inlet
Earthing terminals not connected to neutral terminal N
Class 0, II and III appliance have no provision for P
earthing
Safety extra-low voltage circuits not earthed, unless N
protective extra-low voltage circuits
One pole of spark-ignition circuit supplied through an P
ignition transformer complying with IEC 61558-1 is
earthed (IEC/EN 60335-2-102)

29 CLEARANCES, CREEPAGE DISTANCES AND SOLID INSULATION -

29.1 The requirement is not applicable to spark-ignition P
circuits complying with the values specified in8.101.
For other spark-ignition circuits, the requirement is
not applicable to the air gap between the electrodes
(IEC 60335-2-102)

30 RESISTANCE TO HEAT AND FIRE -

30.2 Parts of non-metallic material adequately resistant to P
ignition and spread of fire
The tests of 30.2.2 is applicable to manually P
operated spark-ignition circuits. to other circuits
(IEC/EN 60335-2-102)

Accredited Testing Laboratory

 Page 99 of 120

Order No. 191659TRFSAF

ATTACHMENT 2 TO TEST REPORT IEC 60335-2-6

EUROPEAN GROUP DIFFERENCES AND NATIONAL DIFFERENCES
(Household and similar electrical appliances – Safety –
PART 2: PARTICULAR REQUIREMENTS FOR STATIONARY COOKING RANGES, HOBS, OVENS AND
SIMILAR APPLIANCES)
Differences according to ................ : EN 60335-2-6 2003 + A1:2003 + A2: 2008used in conjunction with
EN 60335-1:2002 + A11:2004 + A1:2004 + A12:2006 + A2:2006 +
A13:2008 and
EN 62233:2008
Attachment Form No. ..................... : EU_GD_IEC60335_2_6G
Attachment Originator ................... : LCIE
Master Attachment ......................... : Date 2009-10
Copyright © 2009 IEC System for Conformity Testing and Certification of Electrical Equipment
(IECEE), Geneva, Switzerland. All rights reserved.

EN 62233
Clause Requirement + Test Result - Remark Verdict
EMF- ELECTROMAGNETICS FIELDS
The Tested product also complies to the requirements of EN 62233:2008
Limit ……………100% Measured max. :…2.0% P

Accredited Testing Laboratory

 Page 100 of 120

Order No. 198155TRFSAF

EN60335_2_6 - ATTACHMENT
Clause Requirement + Test Result - Remark Verdict

CENELEC COMMON MODIFICATIONS (EN) -

6.1 Delete “class 0” and “class 01” P

7.1 Single-phase appliances to be connected to the P

supply mains: 230 V covered
Multi-phase appliances to be connected to the supply mains: 400 V covered N

24.1.7 If the remote operation of the appliance is via a telecommunication network, the N
relevant standards for the telecommunication interface circuitry in the appliance are
EN 41003 and EN 60950-1:2006, Subclause 6.3
25.6 Supply cords of single-phase portable appliances having a rated current not N
exceeding 16 A, fitted with a plug complying with the following standard sheets of
IEC 60083:1975:
- for Class I appliances: standard sheet C2b, C3b P
or C4 ....................................................................... :
- for Class II appliances: standard sheet C5 or C6 . : N

25.7 Additional type of supply cord:

- ordinary polychloroprene sheathed flexible cord N

(60245 IEC 57)
25.7 Supply cords having high flexibility, not lighter than: -

- rubber insulated and sheathed cord N

(60245 IEC 86)
- rubber insulated, crosslinked PVC sheathed cord N
(60245 IEC 87)
- crosslinked PVC insulated and sheathed cord N
(60245 IEC 88)
29.3 The third dashed item replaced by: N
- an assessment of the thermal quality of the
material combined with an electric strength test, in
accordance with 29.3.3, and, for accessible
reinforced insulation consisting of a single layer,
measurement in accordance with 29.3.Z1
29.3.Z1 For accessible reinforced insulation consisting of a N
single layer, the thickness of the layer complies with
table Z1; rated voltage (V); overvoltage category;
thickness (mm) ........................................................ :

Accredited Testing Laboratory

 Page 101 of 120

Order No. 198155TRFSAF

EN60335_2_6 - ATTACHMENT
Clause Requirement + Test Result - Remark Verdict

Annex ZA ANNEX ZA (NORMATIVE) -

SPECIAL NATIONAL CONDITIONS

Austria
25.6 Plugs according to standard sheet C3b not allowed P
Belgium
25.6 Plugs according to standard sheet C2b not allowed P
Denmark

Accredited Testing Laboratory

 Page 102 of 120

Order No. 198155TRFSAF

EN60335_2_6 - ATTACHMENT
Clause Requirement + Test Result - Remark Verdict

12 Requirements regarding marking tag of power N

supply cord and connection of earthing wire for
class I appliances delivered without a plug
25.6 Supply cords of single-phase portable appliances N
having a rated current not exceeding 13 A provided
with a plug according to the following:
Class I appliances: Section 107-2-D1, ed.3 1998, N
Standard Sheet DK 2-1a
For appliances covered by a Part 2 of EN 60335, N
also plugs in accordance with Section 107-2-D1,
ed. 3, 1998, Standard Sheet C2b, C3b or C4 are
allowed
Class II appliances: Section 107-2-D1, ed.3 1998, N
Standard Sheet C1b, C5, C6, DKA 2-1a and DKA
2-1b
Stationary single-phase appliances, having a rated N
current not exceeding 13 A, and provided with a
supply cord and a plug, the plug is in accordance
with the requirements above
Multi-phase appliances and single-phase N
appliances having a rated current exceeding 13 A,
and provided with a supply cord and a plug, the
plug is in accordance with the requirements below:
Class I appliances: Section 107-2-D1, Standard N
Sheet DK 6-1a / EN 60309-2, Standard Sheet 2-II,
2-IV
Class II appliances: Section 107-2-D1, Standard N
Sheet DK 6-1a / EN 60309-2, Standard Sheet 2-II,
2-IV, the earthing contact not being connected
The current for the plug not exceeding the values N
specified; standard sheet (no.); current (A) ............ :
Finland
25.6 Plugs according to standard sheet C3b not allowed P

France

Accredited Testing Laboratory

 Page 103 of 120

Order No. 198155TRFSAF

EN60335_2_6 - ATTACHMENT
Clause Requirement + Test Result - Remark Verdict

22.2 The second paragraph of this subclause, dealing P

with single-phase, permanently connected class I
appliances having heating elements, is not
applicable due to the supply system
25.6 Plugs according to standard sheet C2b not allowed P
Germany
25.6 Plugs according to standard sheet C3b not allowed P

29.3 Third dashed item not applicable for appliances N

where the insulation is accessible. Additional
measures, such as a multi-layered insulation or
adequate thickness, taken.
Iceland
25.6 Plugs according to standard sheet C3b not allowed P
Ireland
25.6 Plugs according to standard sheet C3b not allowed P

25.6 Only plugs according to Standard Sheets B2 and P

C5 allowed
25.6 These regulations apply to all plugs for domestic P
use at a voltage of not less than 200 V and allow
only plugs complying with I.S. 401:1997, or
equivalent, to be fitted to domestic appliances.
25.8 Replacement of figures (rated current/cross- P
sectional area) in the table
Italy
7.1 The voltage is 220 V/380 V P

25.6 Plugs according to standard sheet C3b not allowed P

25.6 Only plugs listed in CENELEC Report R0BT- P

005:2001 allowed
Luxembourg
25.6 Plugs according to standard sheet C3b not allowed P
Netherlands
25.6 Plugs according to standard sheet C3b not allowed P

Accredited Testing Laboratory

 Page 104 of 120

Order No. 198155TRFSAF

EN60335_2_6 - ATTACHMENT
Clause Requirement + Test Result - Remark Verdict

Norway
19.5 The test is also applicable to appliances intended to P
be permanently connected to fixed wiring
22.2 The second paragraph of this subclause, dealing P
with single-phase, permanently connected class I
appliances having heating elements, is not
applicable due to the supply system
25.6 Plugs according to standard sheet C3b not allowed P
Portugal
25.6 Plugs according to standard sheet C3b not allowed P
Spain
25.6 Plugs according to standard sheet C2b not allowed P

25.6 Plugs according to standard sheet C3b not allowed P

25.6 For appliances for household use, only the P

following plugs are allowed:
according to UNE 20315: ESC 10-1b, C2b, C4, C6 P
or ESB 25-5b
according to UNE-EN 50075 P
Sweden
25.6 Plugs according to standard sheet C3b not allowed P
Switzerland
4 Information about batteries with carbon-zinc and N
alkali-manganese
25.6 Plugs according to standard sheet C3b not allowed N

25.6 Supply cords of portable household and similar N

electrical appliances having a rated current not
exceeding 10 A, provided with a plug complying
with SEV 1011 or IEC 60884-1 and one of the
following dimension sheets:
SEV 6532-2.1991, plug type 15, 3P+N+PE, N
250/400 V, 10 A
SEV 6533-2.1991, plug type 11, L+N, 250 V, 10 A N

SEV 6534-2.1991 plug type 12, L+N+PE, 250 V, N

10 A

Accredited Testing Laboratory

 Page 105 of 120

Order No. 198155TRFSAF

EN60335_2_6 - ATTACHMENT
Clause Requirement + Test Result - Remark Verdict

United Kingdom
25.6 Plugs according to standard sheet C2b not allowed P

25.6 Plugs according to standard sheet C3b not allowed P

25.6 Only plugs according to Standard Sheets B2 and P

C5 allowed
25.6 These regulations apply to all plugs for domestic Proper plug will be provided -
use at a voltage of not less than 200 V and allow with the appliance suitable for
only plugs to BS 1363 to be fitted to domestic the United Kingdom
appliances. It also allows plugs to BS 4573 and
standard sheet C5 to be fitted to shavers and
toothbrushes.
25.8 Replacement of figures (rated current/cross- P
sectional area) in the table

Accredited Testing Laboratory

 Page 106 of 120

Order No. 198155TRFSAF

EN60335_2_102 - ATTACHMENT
Clause Requirement + Test Result - Remark Verdict

ATTACHMENT 3 TO TEST REPORT IEC 60335-2-102

EUROPEAN GROUP DIFFERENCES AND NATIONAL DIFFERENCES
Household and similar electrical appliances – Safety –
Part 2: Particular requirements for gas, oil and solid-fuel burning appliances having electrical connections

Differences according to ................ : EN 60335-2-102:2006 + A1:2008

EN 60335-1:2002 + A11:2004 + A12:2006 + A13:2008 A1:2004
+ A2:2006
EN 62233:2008

Accredited Testing Laboratory

 Page 107 of 120

Order No. 198155TRFSAF

EN60335_2_102 - ATTACHMENT
Clause Requirement + Test Result - Remark Verdict

Group/CENELEC Common Differences to IEC 60335-1:2001 (4. Edition)

6.1 Delete “class 0” and “class 01” P

7.1 Single-phase appliances to be connected to the P
supply mains: 230 V covered
Multi-phase appliances to be connected to the supply N
mains: 400 V covered
24.1.7 If the remote operation of the appliance is via a N
telecommunication network, the relevant standards
for the telecommunication interface circuitry in the
appliance are EN 41003 and EN 60950-1:2006,
Subclause 6.3
25.6 Supply cords of single-phase portable appliances having a rated current not exceeding -
16 A, fitted with a plug complying with the following standard sheets of
IEC 60083:1975:
- for Class I appliances: standard sheet C2b, C3b or P
C4 ............................................................................:
- for Class II appliances: standard sheet C5 or C6 ..: N
25.7 Additional type of supply cord:
- ordinary polychloroprene sheathed flexible cord N
(60245 IEC 57)
25.7 Supply cords having high flexibility, not lighter than:
- rubber insulated and sheathed cord (60245 IEC 86) N
- rubber insulated, crosslinked PVC sheathed cord N
(60245 IEC 87)
- crosslinked PVC insulated and sheathed cord N
(60245 IEC 88)
29.3 The third dashed item replaced by: N
- an assessment of the thermal quality of the material
combined with an electric strength test, in
accordance with 29.3.3, and, for accessible
reinforced insulation consisting of a single layer,
measurement in accordance with 29.3.Z1

Accredited Testing Laboratory

 Page 108 of 120

Order No. 198155TRFSAF

EN60335_2_102 - ATTACHMENT
Clause Requirement + Test Result - Remark Verdict

29.3.Z1 For accessible reinforced insulation consisting of a N

single layer, the thickness of the layer complies with
table Z1; rated voltage (V); overvoltage category;
thickness (mm) .........................................................:
Annex ZC ANNEX ZC (NORMATIVE) -
NORMATIVE REFERENCES TO INTERNATIONAL PUBLICATIONS WITH THEIR
CORRESPONDING EUROPEAN PUBLICATIONS
A list of referenced documents in this standard P
Annex ZD ANNEX ZD (INFORMATIVE)
IEC and CENELEC CODE DESIGNATIONS FOR FLEXIBLE CORDS
A list of code designations for different types of P
flexible cords
National Differences for Austria

25.6 Plugs according to standard sheet C3b not allowed P

National Differences for Belgium

25.6 Plugs according to standard sheet C2b not allowed P

Accredited Testing Laboratory

 Page 109 of 120

Order No. 198155TRFSAF

EN60335_2_102 - ATTACHMENT
Clause Requirement + Test Result - Remark Verdict

National Differences for Denmark

7.12 Requirements regarding marking tag of power supply N

cord and connection of earthing wire for class I
appliances delivered without a plug
25.6 Supply cords of single-phase portable appliances N
having a rated current not exceeding 13 A provided
with a plug according to the following:
Class I appliances: Section 107-2-D1, ed.3 1998, N
Standard Sheet DK 2-1a
For appliances covered by a Part 2 of EN 60335, N
also plugs in accordance with Section 107-2-D1, ed.
3, 1998, Standard Sheet C2b, C3b or C4 are allowed
Class II appliances: Section 107-2-D1, ed.3 1998, N
Standard Sheet C1b, C5, C6, DKA 2-1a and DKA 2-
1b
Stationary single-phase appliances, having a rated N
current not exceeding 13 A, and provided with a
supply cord and a plug, the plug is in accordance with
the requirements above
Multi-phase appliances and single-phase appliances N
having a rated current exceeding 13 A, and provided
with a supply cord and a plug, the plug is in
accordance with the requirements below:
Class I appliances: Section 107-2-D1, Standard N
Sheet DK 6-1a / EN 60309-2, Standard Sheet 2-II,
2-IV
Class II appliances: Section 107-2-D1, Standard N
Sheet DK 6-1a / EN 60309-2, Standard Sheet 2-II,
2-IV, the earthing contact not being connected
The current for the plug not exceeding the values N
specified; standard sheet (no.); current (A) ............:

National Differences for Finland

25.6 Plugs according to standard sheet C3b not allowed P

Accredited Testing Laboratory

 Page 110 of 120

Order No. 198155TRFSAF

EN60335_2_102 - ATTACHMENT
Clause Requirement + Test Result - Remark Verdict

National Differences for France

22.2 The second paragraph of this subclause, dealing with P

single-phase, permanently connected class I
appliances having heating elements, is not applicable
due to the supply system
25.6 Plugs according to standard sheet C2b not allowed P

National Differences for Germany

25.6 Plugs according to standard sheet C3b not allowed P

29.3 Third dashed item not applicable for appliances N
where the insulation is accessible. Additional
measures, such as a multi-layered insulation or
adequate thickness, taken.

National Differences for Iceland

25.6 Plugs according to standard sheet C3b not allowed P

National Differences for Ireland

25.6 Plugs according to standard sheet C3b not allowed P

25.6 Only plugs according to Standard Sheets B2 and C5 P
allowed
25.6 These regulations apply to all plugs for domestic use P
at a voltage of not less than 200 V and allow only
plugs complying with I.S. 401:1997, or equivalent, to
be fitted to domestic appliances.
25.8 Replacement of figures (rated current/cross-sectional P
area) in the table

Accredited Testing Laboratory

 Page 111 of 120

Order No. 198155TRFSAF

EN60335_2_102 - ATTACHMENT
Clause Requirement + Test Result - Remark Verdict

National Differences for Italy

7.1 The voltage is 220 V/380 V P

25.6 Plugs according to standard sheet C3b not allowed P
25.6 Only plugs listed in CENELEC Report R0BT- P
005:2001 allowed

National Differences for Luxembourg

25.6 Plugs according to standard sheet C3b not allowed P

National Differences for Netherlands

25.6 Plugs according to standard sheet C3b not allowed P

National Differences for Norway

19.5 The test is also applicable to appliances intended to P

be permanently connected to fixed wiring
22.2 The second paragraph of this subclause, dealing with N
single-phase, permanently connected class I
appliances having heating elements, is not applicable
due to the supply system
25.6 Plugs according to standard sheet C3b not allowed P

National Differences for Portugal

25.6 Plugs according to standard sheet C3b not allowed P

Accredited Testing Laboratory

 Page 112 of 120

Order No. 198155TRFSAF

EN60335_2_102 - ATTACHMENT
Clause Requirement + Test Result - Remark Verdict

National Differences for Spain

25.6 Plugs according to standard sheet C2b not allowed P

25.6 Plugs according to standard sheet C3b not allowed P
25.6 For appliances for household use, only the following P
plugs are allowed:
according to UNE 20315: ESC 10-1b, C2b, C4, C6 or P
ESB 25-5b
according to UNE-EN 50075 P
P

National Differences for Sweden

25.6 Plugs according to standard sheet C3b not allowed P

National Differences for Switzerland

4 Information about batteries with carbon-zinc and N

alkali-manganese
25.6 Plugs according to standard sheet C3b not allowed N
25.6 Supply cords of portable household and similar N
electrical appliances having a rated current not
exceeding 10 A, provided with a plug complying with
SEV 1011 or IEC 60884-1 and one of the following
dimension sheets:
SEV 6532-2.1991, plug type 15, 3P+N+PE, N
250/400 V, 10 A
SEV 6533-2.1991, plug type 11, L+N, 250 V, 10 A N
SEV 6534-2.1991 plug type 12, L+N+PE, 250 V, 10 A N

Accredited Testing Laboratory

 Page 113 of 120

Order No. 198155TRFSAF

EN60335_2_102 - ATTACHMENT
Clause Requirement + Test Result - Remark Verdict

National Differences for United Kingdom

25.6 Plugs according to standard sheet C2b not allowed P

25.6 Plugs according to standard sheet C3b not allowed P
25.6 Only plugs according to Standard Sheets B2 and C5 P
allowed
25.6 These regulations apply to all plugs for domestic use Proper plug will be provided -
at a voltage of not less than 200 V and allow only with the appliance suitable for
plugs to BS 1363 to be fitted to domestic appliances. the United Kingdom
It also allows plugs to BS 4573 and standard sheet
C5 to be fitted to shavers and toothbrushes.
25.8 Replacement of figures (rated current/cross-sectional P
area) in the table

Accredited Testing Laboratory

 Page 114 of 120

Order No. 198155TRFSAF

EN60335_2_102 - ATTACHMENT
Clause Requirement + Test Result - Remark Verdict

ST
GROUP DIFFERENCES to IEC 60335-2-102 1 ed.
Clause Requirement – Test Result - Remark Verdict
8.101 Parts of spark-ignition circuit shall not be Continuous spark ignition with: P
accessible if the following limits are exceeded, - Discharge 9,5µAs per pulse
unless they are piezoelectric igniters: - duration: 0,35µs
Pulse spark ignition discharge = 100 µC per pulse - repetition: 0,45s
Continuous spark ignition
•Current = = 0,7 mA (peak)
•no load voltage = ≤10 kV
Or
•no load v ltage = <10 kV(peak)
• Discharge = = ≤ 45 µC per pulse and
•frequen y = 25 Hz
Pulse repetition ignition
• Di charge = = ≤ 45 µC per pulse a
•pulse repetition 25 Hz
frequency
(EN 60335-2-102)
13.2 For appliances which are assembled on site, the N
leakage current and electrical strength tests on
the complete appliance need not be performed if
the components and sub-assemblies have been
separately tested and the interconnection is
carried out in accordance with the manufacturers
instructions. (EN 60335-2-102)
13.2 If the disconnection of protective impedance or N
radio interference filters is not possible, the limit
specified for leakage currents is to be calculated
taking into account the current through those
circuits or components. (EN 60335-2-102)

Accredited Testing Laboratory

 Page 115 of 120

Order No. 198155TRFSAF

EN60335_2_102 - ATTACHMENT
Clause Requirement + Test Result - Remark Verdict

16.3 Compliance of spark ignition circuits is checked P

by inspection and only in case of doubt by the
following test:
Spark ignition circuits or crucial parts are
submitted to an endurance test under the
following conditions:
. maximum duration of switch-on given by the
manufacturer (complete switch-on duration shall
correspond with the realistic time of use);
. the relation between on/off cycles as declared
by the manufacturer;
. maximum rated voltage;
. maximum ambient temperature of all parts
under test.
During the test no breakdown to other circuits or,
if the limits specified in 8.101 are exceeded,
accessible surfaces shall occur. Breakdown to
conductive parts which are connected to earth is
allowed if this does not result in a critical failure
of circuits with safety related functions.
(EN 60335-2-102)
19.2 up to Not applicable N
19.19.10
19.11.2 "short circuit" and "mechanical break-down" of N
relay contacts in protective electronic circuits.
The failure modes need not to be considered if
components comply with IEC 60730-2-5 3rd ed.
including A1. (EN 60335-2-102)
19.11.3 Tests are not repeated for protective electronic N
circuits complying with relevant control standards
such as listed in annex BB. (EN 60335-2-102)
19.11.4 The tests of 19.11.4.1 to 19.11.4.7 are also
carried out under normal operation, the
appliance being supplied at rated voltage.
(EN 60335-2-102)
19.13 During the tests of 19.11.4, the appliance shall N
either continue to operate normally according to
manufacturers specifications, or reach a safe
situation for risks concerning the fuel (shut-down
or lock-out).
After the tests of 19.11.4 on gas and oil-burning
appliances, the appliance shall have reached a
lockout condition as required by the specific
appliance standard (volatile or non-volatile lock-
out see annex AA), unless it continues to
operate normally. (EN 60335-2-102)

Accredited Testing Laboratory

 Page 116 of 120

Order No. 198155TRFSAF

EN60335_2_102 - ATTACHMENT
Clause Requirement + Test Result - Remark Verdict

22.101 Parts of spark-ignition circuits shall be positioned P

or secured against loosening so that contact
between the circuit and other live parts is
prevented. (EN 60335-2-102)
22.102 If compliance with this standard can be affected N
by the polarity of the supply in the event of an
earth fault, the appliance shall incorporate a
polarity-detection device that results in shut-
down or prevents the appliance from operating if
the polarity is reversed.
This requirement does not apply to appliances N
incorporating a control having all-pole
disconnection, to appliances intended to be
permanently connected to fixed wiring, or to
appliances having a supply cord fitted with a
polarized plug. (EN 60335-2-102)
24.1. NOTE 101 A list if standards applicable to N
controls and safety devices is given in annex BB.
(EN 60335-2-102)
24.1.1 Relays and optocouplers which ensure electrical N
isolation between live parts and accessible metal
parts shall comply with EN 60255-1-00, EN
60255-33, EN 116000-1 or EN 120012.
(EN 60335-2-102)
24.101 Appliance outlets and plug connectors of N
interconnection cords shall not be
interchangeable if this could result in a hazard.
27.1 One pole of a spark-ignition circuit supplied P
through an ignition transformer complying with
IEC 61558-2-3 shall be earthed.
(EN 60335-2-102)
29.1 The requirement is not applicable to spark- P
ignition circuits complying with the values
specified in 8.101. For other spark-ignition
circuits, the requirement is not applicable to the
air gap between the electrodes (EN 60335-2-102)
30.2 The test of 30.2.2 is applicable to manually P
operated spark-ignition circuits. The test of
30.2.3 is applicable to other circuits.
(EN 60335-2-102)
AA ANNEX AA (NORMATIVE) ——
Standards for non-electric appliance
(EN 60335-2-102)
Standard use

Accredited Testing Laboratory

 Page 117 of 120

Order No. 198155TRFSAF

EN60335_2_102 - ATTACHMENT
Clause Requirement + Test Result - Remark Verdict

BB ANNEX AA (NORMATIVE) ——
Standards for control and safety devices
Standard use (EN 60335-2-102)

ANNEX EMF
The Tested product also complies to the requirements of EN 62233:2008
Limit ……………100% Measured max. :………2.0% P

Accredited Testing Laboratory

 Page 118 of 120

Order No. 198155TRFSAF

Attachment 4: Photo documentation

Fig. 1 – General view Fig. 2 – General view

Fig. 3 – Lateral view Fig. 4 - Internal view

Accredited Testing Laboratory

 Page 119 of 120

Order No. 198155TRFSAF

Fig. 6 – hob connection block

Fig. 5 - Internal view

Fig. 7 - bottom view Fig. 8 – hobs

Fig. 9 – hob switch Fig. 10 - Hobs (internal parts)

Accredited Testing Laboratory

 Page 120 of 120

Order No. 198155TRFSAF

Fig. 11 – Ignition transformer Fig. 12 – terminal block

Fig. 13 – terminal block ( internal parts) Fig. 14 – terminal block

Fig. 15 – signal lamp

Accredited Testing Laboratory