Clean Agent

Fire Extinguishing System

99 Suppress fire quickly

99 Restricted damages
99 Limited floor space
99 Allow Visibility

www.
SFFECO.com
Technical Datasheet
Clean Agent System
TABLE OF CONTENTS

NO. ITEMS PAGE NO.

I Table of Content 3

II Clean Agent Specification & General Information 4-6

III Modular Cylinders 7

IV Agent Storage Cylinders 8-9

V Valves 10 - 15

VI Electric Solenoid 16

VII Latching Solenoid 17

VIII Local Manual Control Head 18

IX Piston Actuator 19

X Pressure Gauge 20

XI Manifold Check Valve 21

XII Shuttle Check Valve 22

XIII Flexible Hose 23

XIV Liquid Level Indicator 24

XV Discharge Nozzle 25

XVI Discharge Pressure Switch 26

XVII Warning Signs 27

In line with our policy of continuous product improvement, SFFECO reserves the right to modify specifications without prior notice.
KSA CENTRAL-RIYADH KSA WESTERN - JEDDAH KSA EASTERN - DAMMAM SFFECO GLOBAL OFFICE: MADINAH
P.O.Box 4441, P.O.Box 16769, P.O.Box 7162, JAFZA (South), Dubai, UAE. Tel : +966 14 866 0959
Riyadh 14334 Jeddah 21474 Dammam 31462 P.O. Box 261318 Fax: +966 14 866 0969
Tel: +966 11 265 0070 Tel: +966 12 670 6009 Tel: +966 13 835 1961 Tel: +971 4 880 9890 [email protected]
Fax: +966 11 265 2190 Fax: +966 12 676 0307 Fax: +966 13 835 1968 Fax: +971 4 880 9822
[email protected] [email protected] [email protected] E-Mail: [email protected]
www.SFFECO.com
3
Technical Datasheet
Clean Agent System
SPECIFICATION
APPLICATION On a weight-of-agent basis, clean agent is a very
Heptafluoropropane (CF3 CHFCF3 ) fire suppression effective gaseous extinguishing agent. The Clean
agent is the first environmentally acceptable Agent extinguishing concentration for normal Class
replacement for Halon 1301. It has zero ozone A combustibles is approximately 5.8 - 7% by volume.
depleting potential, a low global warming potential, The minimum design concentration for total flood
and a short atmospheric lifetime. It is particularly applications should be in accordance with NFPA
useful where an environmentally acceptable agent is 2001.
essential, where clean-up of other media presents a
problem, where weight versus suppression potential SPECIFICATION
is a factor, where an electrically non-conductive
Clean Agent is manufactured to these specifications:
medium is needed, and where people compatibility
is an overriding factor. Clean Agent can be used to Mole% 99.0 Min.
protect a wide range of applications from sensitive Acidity, ppm by weight 3.0 Max.
electrical equipment to industrial applications
Water content, % by weight 0.001 Max.
using flammable liquids. Consult the current NFPA
Standard 2001 for specific applications. Clean Agent Non-volatile residues,
fire suppression agent is used with SFFECO’s total gram/100Ml 0.05 Max.
flooding systems.
TOXICITY
DESCRIPTION
The toxicology of Clean Agent compares favorable
Clean Agent is an odorless, colorless, liquefied
with that of Halon 1301. The LC50 of Clean Agent
compressed gas. (See Physical Properties Table
is greater than 800,000 ppm which is equivalent
for additional information). It is stored as a liquid
to Halon 1301. Clean Agent has been evaluated for
and dispensed into the hazard as a colorless,
cardiac sensitization via test protocols approved by
electrically non-conductive vapor that is clear and
the United States Environmental Protection Agency.
does not obscure vision. It leaves no residue and
Test results show that cardiac tolerance to Clean
has acceptable toxicity for use in occupied spaces
Agent is much higher than that of Halon 1301 and
at design concentration. Clean Agent extinguishes
will be acceptable for safe use in occupied space
a fire by a combination of chemical and physical
protection. Clean Agent will decompose to form
mechanisms. Clean Agent does not displace oxygen
halogen acids when exposed to open flames. The
and therefore is safe for use in occupied spaces
formation of these acids is minimized by using
without fear of oxygen deprivation.
SFFECO early warning detection systems and proper
PERFORMANCE system installation. When properly applied and
Clean Agent can be used on many types of fires. It is installed, the generation of these by-products by
effective for many surface fires, such as flammable Clean Agent should be minimal.
liquids, and most solid combustible materials.

In line with our policy of continuous product improvement, SFFECO reserves the right to modify specifications without prior notice.
KSA CENTRAL-RIYADH KSA WESTERN - JEDDAH KSA EASTERN - DAMMAM SFFECO GLOBAL OFFICE: MADINAH
P.O.Box 4441, P.O.Box 16769, P.O.Box 7162, JAFZA (South), Dubai, UAE. Tel : +966 14 866 0959
Riyadh 14334 Jeddah 21474 Dammam 31462 P.O. Box 261318 Fax: +966 14 866 0969
Tel: +966 11 265 0070 Tel: +966 12 670 6009 Tel: +966 13 835 1961 Tel: +971 4 880 9890 [email protected]
Fax: +966 11 265 2190 Fax: +966 12 676 0307 Fax: +966 13 835 1968 Fax: +971 4 880 9822
[email protected] [email protected] [email protected] E-Mail: [email protected]
www.SFFECO.com
4
Technical Datasheet
Clean Agent System
PHYSICAL PROPERTIES OF CLEAN AGENT
Chemical Name Heptafluoropropane (CF 3 CHFCF 3 )
Molecular Weight 170.03
Boiling Point @ 760 mm Hg 2.55OF (-16.4OC)
Freezing Point -204OF ( -131.1OC)
Critical Temperature 215OF (101.7OC)
Critical Pressure (psia) 422 psia (2912 kPa)
Critical Volume (ft3/lbm) (cc/mole) 0.0258 (274)
Critical Density (lbm/ft3) 38.8 (621 kg/m3)
Specific Heat, Liquid (BTU/lb-OF) @ 77OF (25OC) 0.283 (1.184 kj/kg/OC)
Specific Heat, Vapor (BTU/lb-OF) @ constant 0.1932 (0.808 kj/kg/OC)
pressure of 1 ATM @ 77OF (25OC)
Heat at Vaporization (BTU/lb) 57.0 (132.6 kj/kg)
at Boiling Point
Thermal Conductivity (BTU/h ftOF) 0.040 (0.069 w/mOC)
of Liquid @ 77OF (25OC)
Viscosity, Liquid (lb/ft hr) @ 77OF (25OC) 0.443 (0.184 centipoise)

Vapor Pressure (psia) @ 77OF (25OC) 66.4 (457.7 kPa)

Ozone Depletion Potential 0
Est. Atmospheric Lifetime (years) 31-42
LC50 (Rats; 4hrs - ppm) >800,000

SAFETY CONSIDERATIONS

Agent Use Conc. NOAEL* Safety Margin

Halon 1301 5% 5% nil
FM 200 7.5 - 8.7% 9% 3% - 20%
Novec TM
1230 5 - 6% 10% 67% - 100%
Inergen 38 - 40% 43% 7% - 13%
CO2 30 - 75% <5% lethal at design concs
* No observable adverse effect level.

In line with our policy of continuous product improvement, SFFECO reserves the right to modify specifications without prior notice.
KSA CENTRAL-RIYADH KSA WESTERN - JEDDAH KSA EASTERN - DAMMAM SFFECO GLOBAL OFFICE: MADINAH
P.O.Box 4441, P.O.Box 16769, P.O.Box 7162, JAFZA (South), Dubai, UAE. Tel : +966 14 866 0959
Riyadh 14334 Jeddah 21474 Dammam 31462 P.O. Box 261318 Fax: +966 14 866 0969
Tel: +966 11 265 0070 Tel: +966 12 670 6009 Tel: +966 13 835 1961 Tel: +971 4 880 9890 [email protected]
Fax: +966 11 265 2190 Fax: +966 12 676 0307 Fax: +966 13 835 1968 Fax: +971 4 880 9822
[email protected] [email protected] [email protected] E-Mail: [email protected]
www.SFFECO.com
5
Technical Datasheet
Clean Agent System
SYSTEM IN GENERAL

The Clean agent fire extinguishing system 1. HFC227ea Storage Components

consists of a series of appropriately sized valves 2. HFC227ea Distribution Components
and cylinders that utilize HFC227ea as the 3. Trim Components
extinguishing medium. Each system consists 4. Slave Arrangement Components
of five basic components and their associated 5. Supplemental Components
accessories. 6. Control Panel
7. Early Warning Detection and alarm Devices

In line with our policy of continuous product improvement, SFFECO reserves the right to modify specifications without prior notice.
KSA CENTRAL-RIYADH KSA WESTERN - JEDDAH KSA EASTERN - DAMMAM SFFECO GLOBAL OFFICE: MADINAH
P.O.Box 4441, P.O.Box 16769, P.O.Box 7162, JAFZA (South), Dubai, UAE. Tel : +966 14 866 0959
Riyadh 14334 Jeddah 21474 Dammam 31462 P.O. Box 261318 Fax: +966 14 866 0969
Tel: +966 11 265 0070 Tel: +966 12 670 6009 Tel: +966 13 835 1961 Tel: +971 4 880 9890 [email protected]
Fax: +966 11 265 2190 Fax: +966 12 676 0307 Fax: +966 13 835 1968 Fax: +971 4 880 9822
[email protected] [email protected] [email protected] E-Mail: [email protected]
www.SFFECO.com
6
Technical Datasheet
Clean Agent System
MODULAR CYLINDERS
DESCRIPTION
SFM modular series is a self-contained stand alone system, ideally economical, simple
and flexible to suit pre-prevailing local conditions. The Design concept of operation
features the sprinkler technology incorporating a gas tight quartzoid bulb sprinkler
head fitted with an optional pyrotechnic electric actuator, 24 vdc, means of actuating
the system can be from a remote controlled release fire extinguishing control panel or
thermally fusing the glass bulb which comes in various fixed temperature ranges.
SFM modular cylinders furnished with ceiling mounting brackets are of carbon steel
material, factory argon/CO2 weld, sand blasted, white finished, oven baked and coated
with electrostatic powder.
SFM extinguishment chemically known as heptaflouropropane (CF3CHFCF3) is a clean
and effective environmentally accepted replacement for halon. It is effective fire
extinguishing agent that can be used on surface fire of flammable liquids and solid
combustible materials. Likewise, effective for total flooding of normally occupied areas
to protect the highly invested equipment.
SFM modular automatic installations are primarily
well-suited for the protection of electrical equipment
rooms, server rooms, gas stations, paint spray booths,
flammable liquid storage areas, engine compartment
in particular for boats and small rooms that are
particularly exposed to danger of fire. Cylinders are
hydrostatically tested at 30 bar.

MODEL SFM 6 SFM 10 SFM 15 SFM 20 SFM 25 SFM 30 SFM 35 SFM 40 SFM 45

AGENT WEIGHT (KG) 6 10 15 20 25 30 35 40 45

MINIMUM FILL RANGE (KG) 2.5 4 6 8 10 13 15 18 20

MAXIMUM FILL RANGE (KG) 6 10 15 20 25 31 36 42 47

PRESSURE (BAR) 15 15 15 15 15 15 15 15 15

VOLUME PROTECTED WITH 7% 10 CU 18 CU 27 CU 36 CU 45 CU 54 CU 63 CU 72 CU 82 CU

CONC. @ 20°C MTR MTR MTR MTR. MTR MTR MTR MTR MTR

TEMP. RATING Standard is 68°C (57°C / 79°C / 93°C / 141°C can be supply upon request)

In line with our policy of continuous product improvement, SFFECO reserves the right to modify specifications without prior notice.
KSA CENTRAL-RIYADH KSA WESTERN - JEDDAH KSA EASTERN - DAMMAM SFFECO GLOBAL OFFICE: MADINAH
P.O.Box 58469, P.O.Box 16769, P.O.Box 7162, JAFZA (South), Dubai, UAE. Tel : +966 14 866 0959
Riyadh 11515 Jeddah 21474 Dammam 31462 P.O. Box 261318 Fax: +966 14 866 0969
Tel: +966 11 265 0070 Tel: +966 12 670 6009 Tel: +966 13 835 1961 Tel: +971 4 880 9890 [email protected]
Fax: +966 11 265 2190 Fax: +966 12 676 0307 Fax: +966 13 835 1968 Fax: +971 4 880 9822
[email protected] [email protected] [email protected] E-Mail: [email protected]
www.SFFECO.com
3
Technical Datasheet
Clean Agent System
AGENT STORAGE CYLINDERS
DESCRIPTION
The Clean Agent cylinders are filled with one pound increments, as given in the
Table-1, to meet the exact amount of agent required. The quantity of agent required
for each enclosure can be calculated using SFFECO software, version SF 3.10 (or 4.0),
which contains a sophisticated calculation routine for predicting the two-phase as
well as two-component flow of agent and nitrogen through the distribution piping
network in quasi-steady state from the initiation of the discharge to final gas blow
down. The cylinder is then super-pressurized with dry nitrogen to 360 psi at 70°F
to provide extinguishment in 10 seconds or less. The 4’’ stainless steel valve offers
excellent flow characteristics for the liquefied gas, allows for long pipe runs and has a
greater coverage area. This is the largest Clean Agent cylinder currently manufactured
and designed for very large applications. The 1200 lb, 1000 lb and 800 lb. cylinders
are manufactured, tested and stamped in accordance with DOT 4BW500.

CYLINDER DIMENSION CYLINDER BRACKET

WALL STRAP
OCI 60790

CYLINDER DIMENSION CYLINDER

F BRACKET
Temperature Limits: D G

32°F (0°C) to 130°F (54.4°C) WALL STRAP

OCI 60790

E
System Operating Pressure: FLOOR STRAP F
360 psi at 70°F (25.3 kgƒ/cm²at 21.1°C) OCI 60772
D G
E
F
D
G

C
TABLE-1: CYLINDER FILLING DATA & DIMENSIONS
FLOOR STRAP
Model Capacity Fill Capacity Valve A B OCIC60772
SFO 20-800 800 Lbs 353 to 806 lbs 4" 56.701” 47.023” 27.76”
E
F
SFO 20-1000 1000 Lbs 439 to 1008 lbs 4" 64.049” 54.381”
G
27.76” D

SFO 20-1200 1200 Lbs 519 to 1211 lbs 4" 71.516” 61.726” 27.76”
C
CYLINDER BRACKET Type Diameter D E F G

The cylinder bracket is manufactured

SF 60790 from30.0''
carbon steel30.225''
band formed35.2''
to the radius of the cylinder2''as shown in Table-2, with
33.2''

flanges for bolting to continuous slot metal30.0''

SF 60772 framing channel
5'' of 12 gauge steel with corrosion
11.85'' 10.35'' resistant
2'' paint or galvanized. The
channel is to be supplied by the installer. The cylinder bracket shall be secured to a surface that the bracket, that will withstand
a load up to 5 times of the cylinder weight. This precaution is to have the bracket safely support the weight of the cylinder and
the reaction force of the HFC-227 ea Clean Agent when discharge.
TABLE-2: Type Diameter D E F G
CYLINDER BRACKET SF 60790 30.0'' 30.225'' 35.2'' 33.2'' 2''
(WALL AND FLOOR STRAP)
SF 60772 30.0'' 5'' 11.85'' 10.35'' 2''

In line with our policy of continuous product improvement, SFFECO reserves the right to modify specifications without prior notice.
KSA CENTRAL-RIYADH KSA WESTERN - JEDDAH KSA EASTERN - DAMMAM SFFECO GLOBAL OFFICE: MADINAH
P.O.Box 4441, P.O.Box 16769, P.O.Box 7162, JAFZA (South), Dubai, UAE. Tel : +966 14 866 0959
Riyadh 14334 Jeddah 21474 Dammam 31462 P.O. Box 261318 Fax: +966 14 866 0969
Tel: +966 11 265 0070 Tel: +966 12 670 6009 Tel: +966 13 835 1961 Tel: +971 4 880 9890 [email protected]
Fax: +966 11 265 2190 Fax: +966 12 676 0307 Fax: +966 13 835 1968 Fax: +971 4 880 9822
[email protected] [email protected] [email protected] E-Mail: [email protected]
www.SFFECO.com
8
Technical Datasheet
Clean Agent System
AGENT STORAGE CYLINDERS
DESCRIPTION
The Clean Agent cylinders are manufactured, tested and stamped in accordance with DOT 4BW500 or DOT 4BA500. All cylinders
are equipped with differential pressure valve. A piston in the valve bore is equipped with a rubber seal that keeps the HFC-
227ea Clean Agent under pressure within the cylinder. Since the area at the top of the piston is greater than the area at the
bottom of the piston, the net force seals the piston against the valve discharge outlet. When the cylinder pressure on the top
of the piston is relieved by means of automatic or manual activation, there is only cylinder pressure acting against the piston
seal, and the piston slide to full open position, allowing cylinder discharge through the distribution piping network. Each of the
basic sizes can be filled with one pound increments to meet the exact amount of HFC-227ea Clean Agent required, within their
fill ranges as shown in the table below.

TEMPERATURE LIMITS:
32°F (0°C)to 130°F (54.4°C)
SYSTEM OPERATING PRESSURE: E
360 psi at 70°F (25.3 kgƒ/cm² at 21.1°C )
C FOAM TAPE
B D

CYLINDER BRACKET F
The cylinder bracket is manufactured from carbon G
A
steel band formed to the radius of the cylinder
CYLINDER BRACKET DIMENSIONS
as shown in Table-3 with flanges for bolting to
continuous slot metal framing channel of 12-gauge Cylinder Cylinder Bracket Part
D E F G
Model Outer Dia. No.
steel with corrosion resistant paint or galvanized. The
SFO 20-20 10.75" 11.00" 14.00" 12.60" 2.00" OCI 50139
channel shall be supplied by the installer. The cylinder SFO 20-35 10.75" 11.00" 14.00" 12.60" 2.00" OCI 50139
bracket shall be secured to a surface that, the bracket SFO 20-70 10.75" 11.00" 14.00" 12.60" 2.00" OCI 50139
SFO 20-100 12.80" 13.00" 16.05" 14.65" 2.00" OCI 60780
will withstand a load up to 5 times of the cylinder
SFO 20-150 12.80" 13.00" 16.05" 14.65" 2.00" OCI 60780
weight. This precaution is to have the bracket safely SFO 20-250 16.00" 16.25" 19.20" 17.80" 2.00" OCI 60760
support the weight of the cylinder and the reaction SFO 20-375 16.00" 16.25" 19.20" 17.80" 2.00" OCI 60760
force of the HFC-227ea Clean Agent when discharged. SFO 20-560 20.00" 20.25" 23.20" 21.70" 2.00" OCI 60770

CYLINDER FILLING DATA AND DIMENSIONS

Model Capacity Fill Capacity Valve A B C
SFO 20-20 20 Lbs 12 to 20 lbs 1" 10.75” 13.8” 18.5”
SFO 20-35 35 Lbs 16 to 35 1" 10.75” 18.7” 23.5”
SFO 20-70 70 Lbs 36 to 71 lbs 1" 10.75” 27.2” 31.9”
SFO 20-100 100 Lbs 44 to 101 lbs 1-1/2” 12.8” 28” 32.9”
SFO 20-150 150 Lbs 71 to 152 lbs 1-1/2" 12.8” 37.4” 42.9”
SFO 20-250 250 Lbs 153 to 253 lbs 1-1/2" 16” 39.8” 42.9”
SFO 20-375 375 Lbs 254 to 379 lbs 2-1/2" 16” 57.1” 64.9”
SFO 20-560 560 Lbs 380 to 561 lbs 2-1/2" 20” 55.7” 63.6”

In line with our policy of continuous product improvement, SFFECO reserves the right to modify specifications without prior notice.
KSA CENTRAL-RIYADH KSA WESTERN - JEDDAH KSA EASTERN - DAMMAM SFFECO GLOBAL OFFICE: MADINAH
P.O.Box 4441, P.O.Box 16769, P.O.Box 7162, JAFZA (South), Dubai, UAE. Tel : +966 14 866 0959
Riyadh 14334 Jeddah 21474 Dammam 31462 P.O. Box 261318 Fax: +966 14 866 0969
Tel: +966 11 265 0070 Tel: +966 12 670 6009 Tel: +966 13 835 1961 Tel: +971 4 880 9890 [email protected]
Fax: +966 11 265 2190 Fax: +966 12 676 0307 Fax: +966 13 835 1968 Fax: +971 4 880 9822
[email protected] [email protected] [email protected] E-Mail: [email protected]
www.SFFECO.com
9
Technical Datasheet
Clean Agent System
1/2 INCH VALVE (PRE-ENGINEERED)

DESCRIPTION

The inch cylinder valve is a high flow Piston

ive valve with a brass body, a stainless steel
piston stem and a R rubber seat. The inch
valve is in sealed position (closed) when the cylinder
is filled with HFC-2 and super pressurized with
dry nitrogen to psi. When cylinder pressure is
applied to the upper chamber of the inch valve,
the piston will be driven downwards. Thus, opening
the valve for the HFC-22 to be discharged
through its outlet.

The inch cylinder valves are installed in lb, lb, VALVE IN OPENED VALVE IN CLOSED
1 lb cylinders in Pre-Engineered Systems. POSITION POSITION

VALVE FRONT VIEW

VALVE WITH ELECTRIC SOLENOID

ELECTRIC
SOLENOID

FRONT VIEW SIDE VIEW VALVE IN OPENED VALVE IN CLOSED

POSITION POSITION

VALVE SIDE VIEW

VALVE WITH ELECTRIC SOLENOID VALVE WITH ELECTRIC SOLENOID

In line with our policy of continuous product improvement, SFFECO reserves the right to modify specifications without prior notice.
KSA CENTRAL-RIYADH KSA WESTERN - JEDDAH KSA EASTERN - DAMMAM SFFECO GLOBAL OFFICE: MADINAH
P.O.Box 4441, P.O.Box 16769, P.O.Box 7162, JAFZA (South), Dubai, UAE. Tel : +966 14 866 0959
Riyadh 14334 Jeddah 21474 Dammam 31462 P.O. Box 261318 Fax: +966 14 866 0969
Tel: +966 11 265 0070 Tel: +966 12 670 6009 Tel: +966 13 835 1961 Tel: +971 4 880 9890 [email protected]
Fax: +966 11 265 2190 Fax: +966 12 676 0307 Fax: +966 13 835 1968 Fax: +971 4 880 9822
[email protected] [email protected] [email protected] E-Mail: [email protected]
www.SFFECO.com
10
Technical Datasheet
Clean Agent System
1 INCH VALVE (PRE-ENGINEERED)

DESCRIPTION
The 1 inch cylinder valve is a high flow Pisto
valve with a brass body, a stainless steel piston
stem and a R rubber seat. The 1 inch valve is in
sealed position (closed) when the cylinder is filled
with HFC-2 and super pressurized with dry
nitrogen to psi. When cylinder pressure is
applied to the upper chamber of the 1 inch valve,
the piston will be driven downwards. Thus, opening
the valve for the HFC-2 stored within the
cylinder to be discharged through its outlet.

The 1 inch cylinder valves are installed in lb and

rs in Pre-Engineered Systems. VALVE IN OPENED VALVE IN CLOSED
POSITION POSITION

VALVE FRONT VIEW

ELECTRIC
SOLENOID
VALVE WITH ELECTRIC SOLENOID

FRONT VIEW

VALVE IN OPENED VALVE IN CLOSED

POSITION POSITION

VALVE SIDE VIEW

SIDE VIEW
VALVE WITH ELECTRIC SOLENOID
VALVE WITH ELECTRIC SOLENOID

In line with our policy of continuous product improvement, SFFECO reserves the right to modify specifications without prior notice.
KSA CENTRAL-RIYADH KSA WESTERN - JEDDAH KSA EASTERN - DAMMAM SFFECO GLOBAL OFFICE: MADINAH
P.O.Box 4441, P.O.Box 16769, P.O.Box 7162, JAFZA (South), Dubai, UAE. Tel : +966 14 866 0959
Riyadh 14334 Jeddah 21474 Dammam 31462 P.O. Box 261318 Fax: +966 14 866 0969
Tel: +966 11 265 0070 Tel: +966 12 670 6009 Tel: +966 13 835 1961 Tel: +971 4 880 9890 [email protected]
Fax: +966 11 265 2190 Fax: +966 12 676 0307 Fax: +966 13 835 1968 Fax: +971 4 880 9822
[email protected] [email protected] [email protected] E-Mail: [email protected]
www.SFFECO.com
11
Technical Datasheet
Clean Agent System
1 INCH VALVE (ENGINEERED)

DESCRIPTION
The 1 inch cylinder valve is made of ASTM 2
hard brass. It is designed as a back pressure type
valve. The piston in the valve is uipped with a
rubber seal that keeps the HFC Clean Agent
under pressure within the cylinder. A small hole in
the piston allows cylinder pressure to be lized
on both sides of the piston. Since the area at the top
of the piston is greater than the area at the bottom
of the piston, the net force seals the piston against
the valve discharge outlet. When cylinder pressure
on the top of the piston is relieved by means of
automatic or manual actuation, there is only cylinder
pressure acting against the piston seal, and the
piston slides to its full open position, allowing VALVE IN OPENED VALVE IN CLOSED
HFC- a discharge through the valve outlets. POSITION POSITION

The 1 inch cylinder valves are installed in lb and VALVE WITH ELECTRIC SOLENOID
ngineered Systems. AND LOCAL MANUAL CONTROL

LOCAL MANUAL PISTON ACTUATOR

CONTROL

ELECTRIC
SOLENOID

VALVE WITH ELECTRIC VALVE WITH PISTON VALVE IN OPENED VALVE IN CLOSED
SOLENOID AND LOCAL ACTUATOR ONLY POSITION POSITION
MANUAL CONTROL

VALVE FRONT VIEW VALVE WITH PISTON ACTUATOR ONLY

In line with our policy of continuous product improvement, SFFECO reserves the right to modify specifications without prior notice.
KSA CENTRAL-RIYADH KSA WESTERN - JEDDAH KSA EASTERN - DAMMAM SFFECO GLOBAL OFFICE: MADINAH
P.O.Box 4441, P.O.Box 16769, P.O.Box 7162, JAFZA (South), Dubai, UAE. Tel : +966 14 866 0959
Riyadh 14334 Jeddah 21474 Dammam 31462 P.O. Box 261318 Fax: +966 14 866 0969
Tel: +966 11 265 0070 Tel: +966 12 670 6009 Tel: +966 13 835 1961 Tel: +971 4 880 9890 [email protected]
Fax: +966 11 265 2190 Fax: +966 12 676 0307 Fax: +966 13 835 1968 Fax: +971 4 880 9822
[email protected] [email protected] [email protected] E-Mail: [email protected]
www.SFFECO.com
12
 Technical Datasheet
Clean Agent System
1.5 INCH CYLINDER VALVE
DESCRIPTION
The 1 inch cylinder valve is made of ASTM -
hard brass. It is designed as a back pressure
type valve. The piston in the valve is a
rubber seal that keeps the ea Clean Agent
under pressure within the cylinder. A small hole in
the piston allows cylinder pressure to be
on both sides of the piston. Since the area at the top
of the piston is greater than the area at the bottom
of the piston, the net force seals the piston against
the valve discharge outlet. When cylinder pressure
on the top of the piston is relieved by means of
automatic or manual actuation, there is only cylinder
pressure acting against the piston seal, and the
piston slides to its full open position, allowing
VALVE IN OPENED VALVE IN CLOSED
discharge through the valve outlets.
POSITION POSITION

The 1 inch cylinder valves are installed in lb VALVE WITH ELECTRIC SOLENOID
ylinders in Engineered Systems and AND LOCAL MANUAL CONTROL
linders in Pre-Engineered Systems.

LOCAL MANUAL PISTON ACTUATOR

CONTROL

ELECTRIC
SOLENOID

VALVE WITH ELECTRIC VALVE WITH PISTON VALVE IN OPENED VALVE IN CLOSED
SOLENOID AND LOCAL ACTUATOR ONLY POSITION POSITION
MANUAL CONTROL

VALVE FRONT VIEW VALVE WITH PISTON ACTUATOR ONLY

In line with our policy of continuous product improvement, SFFECO reserves the right to modify specifications without prior notice.
KSA CENTRAL-RIYADH KSA WESTERN - JEDDAH KSA EASTERN - DAMMAM SFFECO GLOBAL OFFICE: MADINAH
P.O.Box 4441, P.O.Box 16769, P.O.Box 7162, JAFZA (South), Dubai, UAE. Tel : +966 14 866 0959
Riyadh 14334 Jeddah 21474 Dammam 31462 P.O. Box 261318 Fax: +966 14 866 0969
Tel: +966 11 265 0070 Tel: +966 12 670 6009 Tel: +966 13 835 1961 Tel: +971 4 880 9890 [email protected]
Fax: +966 11 265 2190 Fax: +966 12 676 0307 Fax: +966 13 835 1968 Fax: +971 4 880 9822
[email protected] [email protected] [email protected] E-Mail: [email protected]
www.SFFECO.com
13
Technical Datasheet
Clean Agent System
2.5 INCH CYLINDER VALVE
DESCRIPTION
The 2 inch cylinder valve is made of ASTM
hard brass. It is designed as a back pressure
type valve. The piston in uipped with a
rubber seal that keeps the HFC-2 Clean Agent
under pressure within the cylinder. A small hole in
the piston allows cylinder pressure to be e
on both sides of the piston. Since the area at the top
of the piston is greater than the area at the bottom
of the piston, the net force seals the piston against
the valve discharge outlet. When cylinder pressure
on the top of the piston is relieved by means of
automatic or manual actuation, there is only cylinder
pressure acting against the piston seal, and the
piston slides to its full open position, allowing VALVE IN OPENED VALVE IN CLOSED
ea discharge through the valve outlets. POSITION POSITION

The 2 inch cylinder valves are installed in lb VALVE WITH ELECTRIC SOLENOID
and lb cylinders in Engineered Systems and AND LOCAL MANUAL CONTROL
lb and lb cylinders in Pre-Engineered
Systems.

LOCAL MANUAL PISTON ACTUATOR

CONTROL

ELECTRIC
SOLENOID

VALVE WITH ELECTRIC VALVE WITH PISTON VALVE IN OPENED VALVE IN CLOSED
SOLENOID AND LOCAL ACTUATOR ONLY POSITION POSITION
MANUAL CONTROL

VALVE FRONT VIEW VALVE WITH PISTON ACTUATOR ONLY

In line with our policy of continuous product improvement, SFFECO reserves the right to modify specifications without prior notice.
KSA CENTRAL-RIYADH KSA WESTERN - JEDDAH KSA EASTERN - DAMMAM SFFECO GLOBAL OFFICE: MADINAH
P.O.Box 4441, P.O.Box 16769, P.O.Box 7162, JAFZA (South), Dubai, UAE. Tel : +966 14 866 0959
Riyadh 14334 Jeddah 21474 Dammam 31462 P.O. Box 261318 Fax: +966 14 866 0969
Tel: +966 11 265 0070 Tel: +966 12 670 6009 Tel: +966 13 835 1961 Tel: +971 4 880 9890 [email protected]
Fax: +966 11 265 2190 Fax: +966 12 676 0307 Fax: +966 13 835 1968 Fax: +971 4 880 9822
[email protected] [email protected] [email protected] E-Mail: [email protected]
www.SFFECO.com
14
 Technical Datasheet
Clean Agent System
4 INCH CYLINDER VALVE

DESCRIPTION
The 4 inch cylinder valve is made of
Stainless Steel. It is designed as a back pressure
type valve. The piston in the valve is a
rubber seal that keeps the HFC Clean Agent
under pressure within the cylinder. A small hole in
the piston allows cylinder pressure to be lized
on both sides of the piston. Since the area at the top
of the piston is greater than the area at the bottom
of the piston, the net force seals the piston against
the valve discharge outlet. When cylinder pressure
on the top of the piston is relieved by means of
automatic or manual actuation, there is only cylinder
VALVE IN OPENED VALVE IN CLOSED
pressure acting against the piston seal, and the POSITION
POSITION
piston slides to its full open position, allowing
HFC- a discharge through the valve outlets.
VALVE WITH ELECTRIC SOLENOID
The 4 inch cylinder valves are installed in 1 lb AND LOCAL MANUAL CONTROL
cylinders in Engineered Systems.

LOCAL MANUAL CONTROL

AND ELECTRIC SOLENOID PISTON ACTUATOR

VALVE WITH ELECTRIC VALVE WITH PISTON

SOLENOID AND LOCAL ACTUATOR ONLY VALVE IN OPENED VALVE IN CLOSED
MANUAL CONTROL POSITION POSITION

VALVE ELEVATION VIEW VALVE WITH PISTON ACTUATOR ONLY

In line with our policy of continuous product improvement, SFFECO reserves the right to modify specifications without prior notice.
KSA CENTRAL-RIYADH KSA WESTERN - JEDDAH KSA EASTERN - DAMMAM SFFECO GLOBAL OFFICE: MADINAH
P.O.Box 4441, P.O.Box 16769, P.O.Box 7162, JAFZA (South), Dubai, UAE. Tel : +966 14 866 0959
Riyadh 14334 Jeddah 21474 Dammam 31462 P.O. Box 261318 Fax: +966 14 866 0969
Tel: +966 11 265 0070 Tel: +966 12 670 6009 Tel: +966 13 835 1961 Tel: +971 4 880 9890 [email protected]
Fax: +966 11 265 2190 Fax: +966 12 676 0307 Fax: +966 13 835 1968 Fax: +971 4 880 9822
[email protected] [email protected] [email protected] E-Mail: [email protected]
www.SFFECO.com
15
Technical Datasheet
Clean Agent System
ELECTRIC SOLENOID

DESCRIPTION
The Electric Solenoid valve is a normally closed valve that ires electrical energy to open. It is used to vent the pressure from the top of
the piston in the cylinder valve, allowing the piston to slide upward and commence cylinder discharge. The electric solenoid valves are
available in 24 . The source of the electrical energy will determine the number and rating of the electric solenoid used. The solenoid
circuit must be supervised for a break in the wiring, a ground or a short circuit.
The cylinder discharge valve that is e with a solenoid valve is to be connected to a control panel that is listed for releasing
devices and compatible with SFFECO Fire
Connect solenoid pigtails to actuation circuit wires with wire nuts within a ction box or by means designated by the authority having
sdiction.
Whenever an Electric Solenoid is used as the sole means of actuation, a top plug must be used to seal the top of the cylinder valve.

3 WIRES
1.50'' 1.50''
1 Green - Ground 1.50''
2 Black - Interchangeable +/- 1.15''
.75'' .75''
1.0''

.75''
.75''

1.0'' LABEL
2.0'' 1.60''

.75" .50" 1.25''

.75'' 1.10''

SIDE VIEW TOP VIEW FRONT VIEW

black interchangeable

Termination for Electric Soleno

SIG 1

Connect the terminals of the solenoid to the releasing

SIG 2

module illustration shows in series. A third terminal black interchangeable

(ground) is for grounding. green for ground

Most releasing circuits are supervised by an EOL (End EOL SF -2

SIG 4

of Line) Resistor

NOTE: Two 12 VDC solenoids can be wired in series in a 24 VDC actuating circuit.
Part Number Description Electrical Rating

SF 50025-2 ELECTRIC SOLENOID 24 VDC, 11 Watts

SF 91225-2 ELECTRIC SOLENOID 24 VDC, 15 Watts

In line with our policy of continuous product improvement, SFFECO reserves the right to modify specifications without prior notice.
KSA CENTRAL-RIYADH KSA WESTERN - JEDDAH KSA EASTERN - DAMMAM SFFECO GLOBAL OFFICE: MADINAH
P.O.Box 4441, P.O.Box 16769, P.O.Box 7162, JAFZA (South), Dubai, UAE. Tel : +966 14 866 0959
Riyadh 14334 Jeddah 21474 Dammam 31462 P.O. Box 261318 Fax: +966 14 866 0969
Tel: +966 11 265 0070 Tel: +966 12 670 6009 Tel: +966 13 835 1961 Tel: +971 4 880 9890 [email protected]
Fax: +966 11 265 2190 Fax: +966 12 676 0307 Fax: +966 13 835 1968 Fax: +971 4 880 9822
[email protected] [email protected] [email protected] E-Mail: [email protected]
www.SFFECO.com
16
Technical Datasheet
Clean Agent System
LATCHING SOLENOID WITH LOCAL MANUAL CONTROL HEAD

DESCRIPTION LATCHING SOLENOID ACTUATOR

Latching Solenoid is used to open a Schrader valve on FEATURES:
the top plug adaptor of the cylinder valve. The application High latching forces
Fast response
provides a solution with a fast response and a high Options
latching force to be used with the SFFECO Clean Agent et tool
e button cap

Fire Suppression System. L approved-recognized to

4
Tested in accordance with
It was determined that a latching solenoid with an
optional local manual control head is the best solution for WIRE HAR

the application. The actuator is held in the latched SEALI

position without power until a signal from the agent ISOMETRIC VIEW
release control panel cuts off the permanent magnet. Part Number: SF 50026
When release, the latching solenoid opens the cylinder CHASSIS 2 COIL (-)

valve allowing the extinguishing medium to discharge

from the cylinder into the system. The fast response time POSI )

allows the SFFECO 22 ™ from the system to be released

in the event of a fire. The latching solenoid is designed (Ø ( 1.
with an emergency release local manual control head to
manually force the pin to depress the cylinder valve to (Ø

release the extinguishing medium when needed. In order 1 COIL

to reset the system, the solenoid is to manually returned Ø.12 OF POLE PIECE TO TOP
to the latched position. AL PATTE OF PROTECTIVE CAP
I
ATCHE PRIOR T
P
TECHNICAL SPECIFICATIONS:
Manual Actuation Force lbƒ max SWI
RET
Operating Force lbƒ min R G

E
Power Requirement 24

Current ELECTRICAL DIAGRAM:

ELIEF
Electrical Connection WHITE

Operating Temperature Range ° °C )

SIG 1
LE

Weight kg)
SIG 2

t size)

FOR MANUAL RELEASE

RELEASI

Dimensions ( 41 mm)
( PULL PIN AND
SIG 4

with manual actuation cap EOL PRESS BUTTON

LABEL

LOCAL MANUAL CONTROL HEAD TOR

TO

PLAS
The Local Manual Control Head features a local lever PLASTIC TAMPER
SEAL
driven push rod that depresses a Schrader check valve
thru the latching solenoid when fitted onto the top of the
solenoid, thereby venting the pressure from the top of
the piston in the cylinder valve, allowing the piston to
Ø 1

Material )
slide upward and commence cylinder discharge. The PLEASE THIS AREA

Local Manual Control Head can be mounted directly to a INSTALLED VIEW 2

top plug adapter, which is the top piece of the cylinder

valve. MANUAL ACTUATION BUTTON
Part Number: SF 61033-2

In line with our policy of continuous product improvement, SFFECO reserves the right to modify specifications without prior notice.
KSA CENTRAL-RIYADH KSA WESTERN - JEDDAH KSA EASTERN - DAMMAM SFFECO GLOBAL OFFICE: MADINAH
P.O.Box 4441, P.O.Box 16769, P.O.Box 7162, JAFZA (South), Dubai, UAE. Tel : +966 14 866 0959
Riyadh 14334 Jeddah 21474 Dammam 31462 P.O. Box 261318 Fax: +966 14 866 0969
Tel: +966 11 265 0070 Tel: +966 12 670 6009 Tel: +966 13 835 1961 Tel: +971 4 880 9890 [email protected]
Fax: +966 11 265 2190 Fax: +966 12 676 0307 Fax: +966 13 835 1968 Fax: +971 4 880 9822
[email protected] [email protected] [email protected] E-Mail: [email protected]
www.SFFECO.com
17
Technical Datasheet
Clean Agent System
LOCAL MANUAL CONTROL HEAD

DESCRIPTION
for manual actuation of cylinder
d with safety pull-pin to prevent accidental manual discharge of Clean Agent
Self-venting
Solid brass construction
Stainless steel operation lock pin

3.00'' 3.50''

1.62'' 1.62''
.98'' 1.62''
.98'' .98''
.25''

1.38''

.75''

1.00'' .72''
1.20'' 2.90''
MANUAL .81'' 1.20'' 2.15''
RELEASE 1.62''
1.PULL RING PIN
2.PUSH KNOB .95''
DOWN HARD .81'' .95''

.25''

1.62''

SIDE VIEW TOP VIEW REAR VIEW

The Local Manual Control Head features a local lever driven push rod that depresses a Schrader check valve, thereby venting the
pressure from the top of the piston in the cylinder valve, allowing the piston to slide upward and commence cylinder discharge. The Local
Manual Control Head mounts directly to a top plug adapter, which is located on top of the cylinder valve.

In line with our policy of continuous product improvement, SFFECO reserves the right to modify specifications without prior notice.
KSA CENTRAL-RIYADH KSA WESTERN - JEDDAH KSA EASTERN - DAMMAM SFFECO GLOBAL OFFICE: MADINAH
P.O.Box 4441, P.O.Box 16769, P.O.Box 7162, JAFZA (South), Dubai, UAE. Tel : +966 14 866 0959
Riyadh 14334 Jeddah 21474 Dammam 31462 P.O. Box 261318 Fax: +966 14 866 0969
Tel: +966 11 265 0070 Tel: +966 12 670 6009 Tel: +966 13 835 1961 Tel: +971 4 880 9890 [email protected]
Fax: +966 11 265 2190 Fax: +966 12 676 0307 Fax: +966 13 835 1968 Fax: +971 4 880 9822
[email protected] [email protected] [email protected] E-Mail: [email protected]
www.SFFECO.com
18
Technical Datasheet
Clean Agent System
PISTON ACTUATOR
DESCRIPTION

High brass construction

Mounts directly on top of cylinder valves
Pressure Supplied from Port M of Master
Cylinder Valve
Self-venting
1.75''
0.125''
The Piston Actuator features a pneumatically driven
piston that depresses a Schrader check valve,
thereby venting the pressure from the top of the
piston in the cylinder valve, allowing the piston to 1.875''
slide upward and commence cylinder discharge. The 3.025''
pneumatic pressure ired to operate the Piston
Actuator is obtained from the port of the
cylinder, which is designated as aster cylinder
that is either mechanically a electrically
0.094''

actuated. Multiple cylinders with Piston 1.056''

Actuators can be activated from one master cylinder

using copper tubing or 1 metal flex hose. The
Piston Actuator mounts directly to a top plug
adapter,which is located on top of the cylinder valve.
SECTIONAL VIEW
Piston Actuator Quantities (Piston Actuator Control Head-Slave)
Total Max. Length
Cylinder Size Valve Size Piston Actuator Copper Tube

35 1'' 7 50 ft.

70 1'' 7 50 ft.

150 1 1/2'' 7 50 ft.

250 1 1/2'' 7 50 ft.

375 2 1/2'' 6 30 ft.

560 2 1/2'' 6 30 ft.
1200 4'' 6 30 ft.

NOTE:
When using the metal Flex hose SF
SF SF the
length of the flex hose is to be subtracted from Piston
To return Piston after
operation,Push on the
total length of copper tubing in the Table above- After Operation Piston Rod.

mentioned to determine the max. length of

copper tubing that can be used. At no time may
the total length of copper tubing and the flex hose
exceed the stated length .

In line with our policy of continuous product improvement, SFFECO reserves the right to modify specifications without prior notice.
KSA CENTRAL-RIYADH KSA WESTERN - JEDDAH KSA EASTERN - DAMMAM SFFECO GLOBAL OFFICE: MADINAH
P.O.Box 4441, P.O.Box 16769, P.O.Box 7162, JAFZA (South), Dubai, UAE. Tel : +966 14 866 0959
Riyadh 14334 Jeddah 21474 Dammam 31462 P.O. Box 261318 Fax: +966 14 866 0969
Tel: +966 11 265 0070 Tel: +966 12 670 6009 Tel: +966 13 835 1961 Tel: +971 4 880 9890 [email protected]
Fax: +966 11 265 2190 Fax: +966 12 676 0307 Fax: +966 13 835 1968 Fax: +971 4 880 9822
[email protected] [email protected] [email protected] E-Mail: [email protected]
www.SFFECO.com
19
Technical Datasheet
Clean Agent System
PRESSURE GAUGES
1.055

240 PSI PRESSURE GAUGE AR T .440

APPL TO SMO RFACES.

Part Number: SF 27-15-18 °

°
° °
°
GRE

NOTES: 12° ° .365

12°

1. All Printing are no mor m center of dial.

2.
°
1
F 1
e (white) AR
GE
O
VE F
R
ELLOW POI ER H
Pie area (red,green,red)

CHAR E
C
RE
Ø 1.420 1.230
All printing (black)
Mark (black) M
lack) SE L
WHITE

s ar m center (black) WITH

HFC 22
ea O

4. Font sizes (color

Over (black) 1.420
Point- e with HFC22 ea onl (black)
Point- ps , ,
FRONT VIEW SIDE VIEW

1.055

AR T
APPL TO SMO RFACES. .440

360 PSI PRESSURE GAUGE GRE

Part Number: SF 27-15-17 °
°
°

.365
°
42°
NOTES:

1. All Printing are no mor m center of dial. 12° 2

2F 1 2

2. AR
GE
O
VE F
R
LOW PO TER H 12°
e (white)
CHAR E
REC

°
Ø 1.605 1.415
Pie area (red,green,red)
All printing (black)
M
Mark (black)
L
lack)
SE
WHITE WITH
HFC 22
ea O

s ar m center (black)
4. Point - , ercharged 1.605
Point - ,
Point - ps ,
ck) FRONT VIEW SIDE VIEW

In line with our policy of continuous product improvement, SFFECO reserves the right to modify specifications without prior notice.
KSA CENTRAL-RIYADH KSA WESTERN - JEDDAH KSA EASTERN - DAMMAM SFFECO GLOBAL OFFICE: MADINAH
P.O.Box 4441, P.O.Box 16769, P.O.Box 7162, JAFZA (South), Dubai, UAE. Tel : +966 14 866 0959
Riyadh 14334 Jeddah 21474 Dammam 31462 P.O. Box 261318 Fax: +966 14 866 0969
Tel: +966 11 265 0070 Tel: +966 12 670 6009 Tel: +966 13 835 1961 Tel: +971 4 880 9890 [email protected]
Fax: +966 11 265 2190 Fax: +966 12 676 0307 Fax: +966 13 835 1968 Fax: +971 4 880 9822
[email protected] [email protected] [email protected] E-Mail: [email protected]
www.SFFECO.com
20
Technical Datasheet
Clean Agent System
MANIFOLD CHECK VALVE

DESCRIPTION

Check Valves are used when two or more

agent storage cylinders are manifolded 1 eck Valve (S 2 eck Valve (S
together with one common discharge piping
configuration. Their purpose is to prevent the
loss of agent in the event that any of the agent
storage cylinders are not connected to the
manifold at time of system discharge and to
prevent back flow of agent into other cylinders
attached to the manifold.
All components of the Check Valves are
constructed from brass for durability and
protection against corrosion. The metal to
metal sealing area of the disc and seat is
precision lapped, providing a very tight shut-off TOP VIEW TOP VIEW
of both gas a uid.
1 ck Valve (SF
PT

Pipe Threads

T
1 PT

TOP VIEW FRONT VIEW FRONT VIEW

4 ck Valve (SF
NOTE:
The 1 and 2
1 2 Check Valves must
be installed in the
vertical position only
with check disc on top.

TOP VIEW SIDE VIEW SECTIONAL VIEW

Part Number Description Valve Size

SF 60261 Check Valve 1''

SF 60262 Check Valve 1 1/2''

SF 60263 Check Valve 2 1/2''

SF 60264 Check Valve 4''

In line with our policy of continuous product improvement, SFFECO reserves the right to modify specifications without prior notice.
KSA CENTRAL-RIYADH KSA WESTERN - JEDDAH KSA EASTERN - DAMMAM SFFECO GLOBAL OFFICE: MADINAH
P.O.Box 4441, P.O.Box 16769, P.O.Box 7162, JAFZA (South), Dubai, UAE. Tel : +966 14 866 0959
Riyadh 14334 Jeddah 21474 Dammam 31462 P.O. Box 261318 Fax: +966 14 866 0969
Tel: +966 11 265 0070 Tel: +966 12 670 6009 Tel: +966 13 835 1961 Tel: +971 4 880 9890 [email protected]
Fax: +966 11 265 2190 Fax: +966 12 676 0307 Fax: +966 13 835 1968 Fax: +971 4 880 9822
[email protected] [email protected] [email protected] E-Mail: [email protected]
www.SFFECO.com
21
 Technical Datasheet
Clean Agent System
SHUTTLE CHECK VALVE 1” & 1.5”

DESCRIPTION

The brass shuttle valve is used to connect two

cylinders to a common discharge pipe and
nozzle(s). All threads are available with or
The purpose of having a reserve
supply is that after the first cylinder (main) is
discharged, the second cylinder (reserve) can
be manually transferred via serve
switch to restore fire fighting readiness.

The shuttle valve contains a shuttle check that

closes off the piping to the first cylinder (main)
when empty. When the second cylinder is
discharged, the shuttle check prevents the
charge of the second cylinder into the first
empty cylinder (main) connected on the same
manifold, thus reducing unnecessary Clean
Agent loss.

Part Number Description

SF 50123 Shuttle Check Valve 1''
ISOMETRIC VIEW: Shuttle Check Valve 1 1/2''
SF 60619 Shuttle Check Valve 1 1/2''

1 1/2'' NPT Outlet Path to Nozzles 1'' NPT Outlet Path to Nozzles

3 1/4 inch
2 3/8 inch

From Cylinder Outlet From Cylinder Outlet From Cylinder Outlet From Cylinder Outlet
1'' NPT 1'' NPT 1'' NPT 1'' NPT

6 inch
6 1/4 inch

Shuttle Valve (Part ) for use Shuttle Valve 1 Part

with Model SF E or M with Model SF r Mo

In line with our policy of continuous product improvement, SFFECO reserves the right to modify specifications without prior notice.
KSA CENTRAL-RIYADH KSA WESTERN - JEDDAH KSA EASTERN - DAMMAM SFFECO GLOBAL OFFICE: MADINAH
P.O.Box 4441, P.O.Box 16769, P.O.Box 7162, JAFZA (South), Dubai, UAE. Tel : +966 14 866 0959
Riyadh 14334 Jeddah 21474 Dammam 31462 P.O. Box 261318 Fax: +966 14 866 0969
Tel: +966 11 265 0070 Tel: +966 12 670 6009 Tel: +966 13 835 1961 Tel: +971 4 880 9890 [email protected]
Fax: +966 11 265 2190 Fax: +966 12 676 0307 Fax: +966 13 835 1968 Fax: +971 4 880 9822
[email protected] [email protected] [email protected] E-Mail: [email protected]
www.SFFECO.com
22
Technical Datasheet
Clean Agent System
FLEXIBLE HOSES

DESCRIPTION

The Flex hoses are used to connect the agent storage containers to the manifold in multiple cylinders arrangement. Flex
hoses are constructed of high pressure hydraulic rubber in the and sizes and stainless steel corrugated inner core
with stainless steel braided in the 2-1 size. All sizes are fitted with mal T thread on both ends.
There are two options available for the lb. cylinder. They are a flex hose alone and flex hose check valve assembly.
The flex hose alone is in diameter (Part SF ) and in length. The combination of flex hose and check valve,
which has a diameter of (Part SF 1) and a length of , is used when using a manifold in a piping network. All
are manufactured from a stainless steel corrugated inner core with stainless steel braided. The flex hose has Victaulic
fittings on both ends.
30-1/2''
4.0''
3.0'' 24.0'' 3.0'' 4.0" Victaulic Pipe

4.0'' 4.0''

6" Victaulic Pipe

6'' SIDE VIEW TOP VIEW

4" Victaulic Pipe
SF 91230 4.0''
26-1/2'' 4.0" Victaulic Pipe

6'' 4.0'' 4.0''

SIDE VIEW TOP VIEW

TOP VIEW LF 91231

Part Number Description Length Diameter Material

Flex Hose Stainless Steel ided

1 Flex Hose Check Stainless Steel aided

A Hose (Stainless Steel Braided)

Male NPT for Connection to Hose ( Rubber ) Male NPT for Connection to 2 1/2'' Male NPT for Connection
Cylinder Valve Check Valve or System Pipe to Cylinder Valve

PART NO. A B MATERIAL PART NO. A B MATERIAL PART NO. A B MATERIAL

1 R 2 STEEL

In line with our policy of continuous product improvement, SFFECO reserves the right to modify specifications without prior notice.
KSA CENTRAL-RIYADH KSA WESTERN - JEDDAH KSA EASTERN - DAMMAM SFFECO GLOBAL OFFICE: MADINAH
P.O.Box 4441, P.O.Box 16769, P.O.Box 7162, JAFZA (South), Dubai, UAE. Tel : +966 14 866 0959
Riyadh 14334 Jeddah 21474 Dammam 31462 P.O. Box 261318 Fax: +966 14 866 0969
Tel: +966 11 265 0070 Tel: +966 12 670 6009 Tel: +966 13 835 1961 Tel: +971 4 880 9890 [email protected]
Fax: +966 11 265 2190 Fax: +966 12 676 0307 Fax: +966 13 835 1968 Fax: +971 4 880 9822
[email protected] [email protected] [email protected] E-Mail: [email protected]
www.SFFECO.com
23
Technical Datasheet
Clean Agent System
LIQUID LEVEL INDICATOR (OPTIONAL)

DESCRIPTION
The Level Indicator is a simple, manually operated device, which provides a means to determine the Clean
Agent level in vertically mounted agent storage containers. Once the level is determined, it can then be
converted into the weight of Clean Agent present in the agent storage container .

OPERATION C

A magnet e float moves with the level along the unit stem. Level readout
is obtained by simply removing the protective cap and pulling out a calibrated tape until C

magnetic interlock with the float is felt. With the tape in this position, the reading is
obtained at the point where the tape emerges from the unit housing. TOP VIEW
C

When the is determined, the reading is then referred to a chart in the

Engineering Manual and the corresponding weight of Clean Agent is determined.
Accurate readings can be obtained over a temperature range. D

FEATURES
Reduced Maintenance Time - Weight in an agent storage container
can be determined in a fraction of the time it would take to remove and
weigh them. Tube

Continuous Fire Protection - of the level indicator does not

ire taking out the cylinder from the system, thus providing
uninterrupted fire protection.
Field Installation Capability - The indicator can easily be installed in
the field using a single wrench as long as the container is empty and is
e with a mounting boss. A B

Compact - When not in use, the uires no more space than that
container.
Flexibility - The flexible tape design allows the unit to be used in tight
spaces that would otherwise hinder the use of a rigid type
indicato Float
2.0''
Availability - s are available for all SFFECO containers from sizes of

Part Number
Part Number Description A B C D
SF 60020 Liquid Level Indicator for 150 LB & 250 Cylinders 26'' 29'' 1 1/2'' 3''

SF 60020-1 Liquid Level Indicator for 375 LB & 560 Cylinders 40'' 43'' 1 1/2'' 3''
FRONT VIEW

SF 60020-2 Liquid Level Indicator for 1200 LB Cylinders 40'' 43'' 1 1/2'' 3''

In line with our policy of continuous product improvement, SFFECO reserves the right to modify specifications without prior notice.
KSA CENTRAL-RIYADH KSA WESTERN - JEDDAH KSA EASTERN - DAMMAM SFFECO GLOBAL OFFICE: MADINAH
P.O.Box 4441, P.O.Box 16769, P.O.Box 7162, JAFZA (South), Dubai, UAE. Tel : +966 14 866 0959
Riyadh 14334 Jeddah 21474 Dammam 31462 P.O. Box 261318 Fax: +966 14 866 0969
Tel: +966 11 265 0070 Tel: +966 12 670 6009 Tel: +966 13 835 1961 Tel: +971 4 880 9890 [email protected]
Fax: +966 11 265 2190 Fax: +966 12 676 0307 Fax: +966 13 835 1968 Fax: +971 4 880 9822
[email protected] [email protected] [email protected] E-Mail: [email protected]
www.SFFECO.com
24
Technical Datasheet
Clean Agent System
Discharge Nozzle
DESCRIPTION
The function of the Discharge Nozzle, in a fire extinguishing system, is to distribute the
Clean Agent in a uniform, pre-determined pattern and concentration. The nozzles are
designed to complete the discharge of Clean Agent in 10 seconds or less when installed
within the design limitations stated in the installation instructional manual.

B
A IDENTIFICATION

180 DEG. S
8-HOLES
E 4 sets of holes
G 60 deg. apart.

F 60°REF.
D D
30°REF.
B
IDENTIFICATION

360 DEG. S
8-HOLES
C C 8 sets of holes
45 deg. apart.
45°REF.
45°REF.
180 DEG. 360 DEG.
8-HOLES 8-HOLES
45°REF.
Discharge Nozzle Selection-Sidewall 180°
Typically to be installed acent to the center of the one wall of one enclosure. Its discharge path will be across the enclosure. At no time
shall the area coverage be exceeded.
Discharge Nozzle Selection-Central 360°
Typically to be installed at the center of the enclosure. Its discharge path will be across the enclosure. At no time shall the area coverage be exceeded.
Part Nozzle A DIMENSIONS
DRILL DIAMETER Part Nozzle A DIMENSIONS
DRILL DIAMETER
Number Type NPT B C D E F G RANGE Number Type NPT B C D E F G RANGE

SF 60704-2 180° 0.0781 SF 60707-2 180° 0.2187

1.050 2.050 N/A 1.560 2.560 N/A
Sidewall Sidewall
1/2 1.50 0.918 2.725 TO 1-1/4 2 1.7 3.250 TO
360° 360°
SF 60704-3 Central
N/A N/A 1.875 0.1960 SF 60707-3 Central
N/A N/A 2 0.4375

SF 60705-2 180° 0.1360 SF 60708-2 180° 0.2570

1.000 2.000 N/A 1.300 2.800 N/A
Sidewall Sidewall
3/4 1.50 1.21 2.875 TO 1-1/2 2.25 2.0 3.490 TO
SF 60705-3 360° 0.2610 SF 60708-3 360° 0.5000
Central N/A N/A 2.000 Central N/A N/A 2.25

SF 60706-2 180° 0.1660 SF 60709-2 180° 0.3281

1.250 2.250 N/A 1.810 3.170 N/A
Sidewall Sidewall
1 1.75 1.356 2.950 TO 2 3 2.572 3.788 TO
SF 60706-3 360°
N/A N/A 2.000 0.3320 SF 60709-3 360°
N/A N/A 2.375 0.6563
Central Central

INSTALLATION
Refer to SFF s Installation, Maintenance Service Technical Manual for charge zle Area Coverage and Application Selections

In line with our policy of continuous product improvement, SFFECO reserves the right to modify specifications without prior notice.
KSA CENTRAL-RIYADH KSA WESTERN - JEDDAH KSA EASTERN - DAMMAM SFFECO GLOBAL OFFICE: MADINAH
P.O.Box 4441, P.O.Box 16769, P.O.Box 7162, JAFZA (South), Dubai, UAE. Tel : +966 14 866 0959
Riyadh 14334 Jeddah 21474 Dammam 31462 P.O. Box 261318 Fax: +966 14 866 0969
Tel: +966 11 265 0070 Tel: +966 12 670 6009 Tel: +966 13 835 1961 Tel: +971 4 880 9890 [email protected]
Fax: +966 11 265 2190 Fax: +966 12 676 0307 Fax: +966 13 835 1968 Fax: +971 4 880 9822
[email protected] [email protected] [email protected] E-Mail: [email protected]
www.SFFECO.com
25
Technical Datasheet
Clean Agent System
DISCHARGE PRESSURE SWITCH
Upon activation of the cylinder valve, the operation pressure switches contacts transfer to
indicate discharge or to perform disconnect/activation required during system operation.

Characteristics:
0.125 – 27 NPT male thread
58± psig actuation pressure
40± psig release pressure TO BE INSTALLED INTO PORT ‘M’
Temperature -65°F
250 proof pressure
5,000 burst pressure
Contacts –Silver – 20 amps
120VAC / 240 VAC DPS 10 -370
Normally open – Normally closed,
Normally Open : Red
Normally Closed : Black
Common : White

PRESSURE SUPERVISORY SWITCH

The Pressure Supervisory Switch is

normally wired into a supervisory
circuit to give a trouble signal upon
activation
Characteristics:
0.125 – 27 NPT male thread PU
BL
UE
RP
430 ± 10 psig actuation pressure BL
AC
K
LE
TO BE INSTALLED INTO PORT ‘P’
Temperature -65°F to 275°F
600 psig proof pressure
5,000 burst pressure
Contacts – Silver 2AMP 28VDC
375 VA 120 VAC Pilot Duty
Normally open – Normally closed,
Normally Open : Blue
Normally Closed : Black
Common : Violet

In line with our policy of continuous product improvement, SFFECO reserves the right to modify specifications without prior notice.
KSA CENTRAL-RIYADH KSA WESTERN - JEDDAH KSA EASTERN - DAMMAM SFFECO GLOBAL OFFICE: MADINAH
P.O.Box 4441, P.O.Box 16769, P.O.Box 7162, JAFZA (South), Dubai, UAE. Tel : +966 14 866 0959
Riyadh 14334 Jeddah 21474 Dammam 31462 P.O. Box 261318 Fax: +966 14 866 0969
Tel: +966 11 265 0070 Tel: +966 12 670 6009 Tel: +966 13 835 1961 Tel: +971 4 880 9890 [email protected]
Fax: +966 11 265 2190 Fax: +966 12 676 0307 Fax: +966 13 835 1968 Fax: +971 4 880 9822
[email protected] [email protected] [email protected] E-Mail: [email protected]
www.SFFECO.com
26
Technical Datasheet
Clean Agent System
WARNING SIGNS

DO NOT ENTER: caution sign to alert

the room is protected by HFC227ea
system and all doors should be closed in

SFFECO case of fire.

HFC227ea GAS Size: 10” x 13”

SFFECO
HFC227ea GAS

FLASHING LIGHT:
SFFECO
HFC227ea GAS
This sign in the event of
a gas discharge.
EVACUATE: caution sign to alert the room is
FLASHING LIGHT Size: 5” x 8”
protected by HFC227ea system and
evacuate the area when alarm sounds.

Size: 8” x 8”

SFFECO
HFC227ea GAS
MANUAL DISCHARGE STATION: SFFECO
HFC227ea GAS
This sign will identify each manual
release associated with HFC227ea
system. This reduces the risk of a manual
SYSTEM ABORT
discharge station being mistaken for a
fire alarm system station.
SYSTEM ABORT: sign to identify the
Size: 8” x 4” presence of the system abort station.

Size: 2.25” x 4”

In line with our policy of continuous product improvement, SFFECO reserves the right to modify specifications without prior notice.
KSA CENTRAL-RIYADH KSA WESTERN - JEDDAH KSA EASTERN - DAMMAM SFFECO GLOBAL OFFICE: MADINAH
P.O.Box 4441, P.O.Box 16769, P.O.Box 7162, JAFZA (South), Dubai, UAE. Tel : +966 14 866 0959
Riyadh 14334 Jeddah 21474 Dammam 31462 P.O. Box 261318 Fax: +966 14 866 0969
Tel: +966 11 265 0070 Tel: +966 12 670 6009 Tel: +966 13 835 1961 Tel: +971 4 880 9890 [email protected]
Fax: +966 11 265 2190 Fax: +966 12 676 0307 Fax: +966 13 835 1968 Fax: +971 4 880 9822
[email protected] [email protected] [email protected] E-Mail: [email protected]
www.SFFECO.com
27