FIRE SAFETY

TESTING &
COMMISSIONING
VERIFICATION
INSPECTION GUIDE
SHEETS

These sheets have been developed by the Accord as a resource

for fire safety engineers and fire safety technicians performing fire
detection and fire protection systems work in RMG factories.
T&CV INSPECTION CHECKLIST
Factory:............................................................................................................ Accord ID: ........................................

Inspector(s): ..................................................................................................... Date of Inspection:............................

AIR SAMPLING DETECTION SYSTEMS

Document Review
Yes No Installation Certificate and Record of Completion is available and on-site
Yes No Approved as-built drawings are available and on-site
Yes No Product Information Sheets and Listing Information is available and on-site
Yes No Correct type of pipe and fittings are provided
Yes No Installation manual for control equipment is available
Yes No ...................................................................................................................................................................................
Yes No ...................................................................................................................................................................................

Pre-Test Activities
Yes No Factory staff has informed workers that testing activities will be conducted
Yes No Contractor has proper testing tools and equipment
Yes No System has no ground faults\troubles\supervisory\or alarm signals present

Inspections
Control Equipment Visual Inspections
Yes No Control equipment panel(s) are installed within spaces meeting the manufacturers operational requirements for
temperature and humidity
Yes No Control equipment panel(s) are accessible and not obstructed
Yes No Control equipment panel(s) are normal condition prior to testing
If no, reason(s): ...........................................................................................................................................................
Yes No Alarm control panel indicates no supervisory or trouble conditions
If yes, reason(s): ..........................................................................................................................................................
Yes No Dedicated power is provided to the Alarm Control Panel
Yes No Circuit breaker or power-disconnects are correctly labeled
Yes No Correct size batteries are provided for FACP and Power Supplies
Yes No Batteries have manufacturing date and the date of installation markings
Yes No Control equipment is monitored by Building Fire Alarm System
Yes No ...................................................................................................................................................................................
Yes No ...................................................................................................................................................................................
Control Equipment Inspection Notes:

These fire safety testing & commissioning verification inspection guide

sheets have been developed by the Accord as a resource for fire safety
engineers and fire safety technicians performing fire detection and fire
protection systems work in RMG factories.
 -2-

Field Device Visual Inspections

Yes No N\A Pipe and fittings used for air-sampling pipe network are listed by manufactuer
Yes No N\A Pipe network is complete and includes end-caps
Yes No N\A Pipe network is properly secured and protected from physical damage
Yes No N\A Sampling ports are spaced correctly and match approved plans
Yes No N\A Sampling ports are correctly identified
Yes No N\A Set points for Alarm are provided (1.5- 2.5% Obscuration per foot)
Yes No N\A Set points for Pre-Alarm are provided (0.0015-0.015% Obscuration per foot)
Yes No N\A Notification appliances are installed as shown on the approved plans
Yes No N\A Notification appliances are not obstructed and secured in place
Yes No N\A Audible notification is provided for all occupied areas served by system
Yes No N\A Door Releasing service is provided for all fire doors
Yes No N\A Door releasing hardware is installed correctly and is complete
Yes No N\A Elevator Recall is provided
Yes No N\A Exhaust Fan shut down is provided
Yes No N\A ...............................................................................................................................................................
Yes No N\A ...............................................................................................................................................................
Field Device Inspection Notes:

Functional Testing
Yes No N\A Control equipment confirmed for primary and secondary power loss supervision
Yes No N\A Networked panels are correctly supervised
Yes No N\A All visual displays and annunciator lamps are functional
Yes No N\A Transport time from the farthest sampling point is within 120 seconds
Yes No N\A Alarm conditions report correctly to Bldg. Fire Alarm System
Yes No N\A Supervisory conditions report correctly to Bldg. Fire Alarm System
Yes No N\A Trouble conditions report correctly to Bldg. Fire Alarm System
Yes No N\A ...............................................................................................................................................................
Yes No N\A ...............................................................................................................................................................
Yes No N\A ...............................................................................................................................................................
Functional Testing Notes:

Post-Test Activities
Yes No N\A Factory staff has informed workers that testing activities are complete
Yes No N\A System has no ground faults\troubles\supervisory\or alarm signals present at the end of testing
Yes No Fire Alarm System is functioning in accordance with approved design documents
If no, reason(s):

These fire safety testing & commissioning verification inspection guide

sheets have been developed by the Accord as a resource for fire safety
engineers and fire safety technicians performing fire detection and fire
protection systems work in RMG factories.
T&CV INSPECTION CHECKLIST
Factory:............................................................................................................ Accord ID: ........................................

Inspector(s): ..................................................................................................... Date of Inspection:............................

FIRE ALARM SYSTEMS

Document Review
Yes No Installation Certificate and Record of Completion is available and on-site
Yes No Approved as-built drawings are available and on-site
Yes No Product Information Sheets and Listing Information is available and on-site
Yes No Does all the necessary equipment have third party listing certificates consistent with products on-site
Yes No Has battery calculation & voltage drop calculation been provided as per as-built drawing
Yes No Correct type of wire and cable is provided
Yes No Installation manual for control equipment is available
Yes No ...................................................................................................................................................................................
Yes No ...................................................................................................................................................................................

Pre-Test Activities
Yes No Factory staff has informed workers that testing activities will be conducted
Yes No Contractor has proper testing tools and equipment
Yes No System has no ground faults\troubles\supervisory\or alarm signals present

Inspections
Control Equipment Visual Inspections
Yes No Control equipment panel(s) are installed within spaces meeting the manufacturers operational requirements for
temperature and humidity
Yes No Control equipment panel(s) are accessible and not obstructed
Yes No Control equipment panel(s) are normal condition prior to testing
If no, reason(s): ...........................................................................................................................................................
Yes No Fire alarm control panel indicates no supervisory or trouble conditions
If yes, reason(s): ..........................................................................................................................................................
Yes No Dedicated power is provided to the FACP
Yes No Circuit breaker or power-disconnects are correctly labeled
Yes No Correct size batteries are provided for FACP and Power Supplies
Yes No Batteries have manufacturing date and the date of installation markings
Yes No Has wiring of control equipment been completed as per manufacturer's instruction
Yes No Wiring entering and leaving control equipment is protected from physical damage and terminated correctly
Yes No End of Line Resistors are located in correct locations for supervised circuits
Yes No Remote control-panels and equipment are properly supervised
Yes No ...................................................................................................................................................................................
Yes No ...................................................................................................................................................................................
Control Equipment Inspection Notes:

These fire safety testing & commissioning verification inspection guide

sheets have been developed by the Accord as a resource for fire safety
engineers and fire safety technicians performing fire detection and fire
protection systems work in RMG factories.
 -2-

Field Device Visual Inspections

Yes No N\A Device locations match approved as-builts
Yes No N\A Device quantities match approved as-builts
Yes No N\A Device Addresses are clearly marked for all initiating devices
Yes No N\A Wiring at devices is not exposed or unprotected
Yes No N\A Manual pull boxes are visible in the path of egress and accessible
Yes No N\A Manual pull boxes are not obstructed or subject to physical damage
Yes No N\A Detector spacing and locations are compliant with approved plans
Yes No N\A Detectors are not obstructed and are secured in place
Yes No N\A Detectors are not located in exterior locations or environments that are beyond the manufacturers
operating ranges for temperature and humidity or will produce nuisance alarms
Yes No N\A Notification appliances are installed as shown on the approved plans
Yes No N\A Notification appliances are not obstructed and secured in place
Yes No N\A Audible notification is provided for all occupied areas
Yes No N\A Supervision of all sprinkler control valves is provided`
Yes No N\A Beam detectors are installed in accessible locations
Yes No N\A Beam detectors have remote test and reset switches – resetting the detector does not require removal
of power or special tools
Yes No N\A Door Releasing service is provided for all fire doors
Yes No N\A Door releasing hardware is installed correctly and is complete
Yes No N\A Elevator Recall is provided
Yes No N\A Exhaust Fan shut down is provided
Yes No N\A ...............................................................................................................................................................
Yes No N\A ...............................................................................................................................................................
Field Device Inspection Notes:

Functional Testing
Yes No N\A Control equipment confirmed for primary and secondary power loss supervision
Yes No N\A Networked panels are correctly supervised
Yes No N\A All visual displays and annunciator lamps are functional
Yes No N\A Correct locations of EOL Resistors are verified for supervised circuits
Yes No N\A Devices tested report correct address at panel for activated or missing devices
Yes No N\A Devices tested for functionality with open SLC circuits
Yes No N\A Voltage drop measured for NAC circuits
Yes No N\A Evacuation message or signaling is understandable
Yes No N\A Audibility for occupied areas is at least 15 dBA above ambient
Yes No N\A Visual notification is synchronized when more than one device is in the same field of view
Yes No N\A Music or PA systems are shut down upon activation of alarm system
Yes No N\A Elevators recall on correct devices
Yes No N\A Exhaust Fans shut down upon activation of fire alarm
Yes No N\A ...............................................................................................................................................................
Yes No N\A ...............................................................................................................................................................
Yes No N\A ...............................................................................................................................................................
Functional Testing Notes:

Post-Test Activities
Yes No N\A Factory staff has informed workers that testing activities are complete
Yes No N\A System has no ground faults\troubles\supervisory\or alarm signals present at the end of testing
Yes No Fire Alarm System is functioning in accordance with approved design documents
If no, reason(s):

These fire safety testing & commissioning verification inspection guide

sheets have been developed by the Accord as a resource for fire safety
engineers and fire safety technicians performing fire detection and fire
protection systems work in RMG factories.
T&CV INSPECTION CHECKLIST
Factory:............................................................................................................ Accord ID: ........................................

Inspector(s): ..................................................................................................... Date of Inspection:............................

FIRE PUMP SYSTEM

Document Review
Yes No N\A Installers Fire Pump Test Report is available and on-site
Yes No N\A As-built drawings are available and on-site
Yes No N\A Equipment information sheets and Listing information is available and on-site
Yes No Does all the necessary equipment have third party listing certificates consistent with products on-site
Yes No N\A Manufacturer’s fire pump test curve included in equipment information, and on site
Electric Pump rated fire flow: ........ gpm at ........ psi
Diesel Pump rated fire flow: ........ gpm at ........ psi

Pre-Test Activities
Yes No N\A Factory staff has informed workers that testing activities will be conducted
Yes No N\A Contractor has proper testing tools and equipment
Yes No N\A Connected Fire Alarm System has no ground faults\troubles\supervisory\or alarm signals present

Inspections
Visual Inspections
Yes No N\A Does diesel fire pump room have adequate ventilation
Yes No N\A Does suction from tank have strainer
Yes No N\A Pump Controllers in Auto and free of trouble signals
Yes No N\A Battery terminals free of corrosion
Yes No N\A Are fuel lines steel pipe
Yes No N\A Is fuel tank properly sized (1 gallon per HP) Tank Size ..........
Yes No N\A All valves are supervised and open or closed as required
Yes No N\A Diesel Fuel Tank size ................. / Level: ................. (½, ¾, 1)
Yes No N\A Water Tank size ................. / Level: ................. (½, ¾, 1)
Yes No N\A Pump(s) provided with positive suction head and clean water supply
Yes No N\A Is vortex plate installed in tank suction
Visual Inspection Notes:

Functional testing (Typical for each floor/zone)

Yes No N\A Jockey pump start pressure: ................. psi (slowly open a valve to lower pressure)
Yes No N\A Electric fire pump start pressure: ................. psi (continue to slowly open a valve to lower pressure)
Maximum flow :................. gpm at:................. psi
Yes No N\A If emergency power is provided:
•When in normal power, start pump then shut down normal power and test generator auto start and
switch to E-power
•When on E-power start pump stop pump then start when E-power running
Yes No N\A Diesel fire pump start pressure: ................. psi (continue to slowly open a valve to lower pressure)
Maximum flow:................. gpm at:................. psi
Yes No N\A Fire pumps should be tested at 150% of flow if water supply is available. Otherwise fire pump should be tested
at the greater of the sprinkler system demand, or standpipe system or 100% of rated flow and pressure.
Yes No N\A Fire pump manual stop or automatic stop (Minimum run times: 10 minutes for electric. 30 minutes for diesel)
Yes No N\A Manual stop fire pumps
Yes No N\A Start fire pumps manually
Stop fire pumps and confirm controllers in auto and free of troubles signals
Diesel Fuel Tank size ................. / Level: .................(½, ¾, 1)
Water Tank size ................. / Level: .................(½, ¾, 1)
Measure water tank fill rate if able: ................. gpm

Inspection Notes:

These fire safety testing & commissioning verification inspection guide

sheets have been developed by the Accord as a resource for fire safety
engineers and fire safety technicians performing fire detection and fire
protection systems work in RMG factories.
T&CV INSPECTION CHECKLIST
Factory:............................................................................................................ Accord ID: ........................................

Inspector(s): ..................................................................................................... Date of Inspection:............................

FIRE SPRINKLER SYSTEM

Document Review
Yes No N\A Installation Certificate and Record of Completion is available and on-site
Yes No N\A Approved as-built drawings are available and on-site
Yes No N\A Product Information Sheets and Listing Information is available and on-site
Yes No N\A Does all the necessary equipment have third party listing certificates consistent with products on-site

Pre-Test Activities
Yes No N\A Factory staff has informed workers that testing activities will be conducted
Yes No N\A Contractor has proper testing tools and equipment

Inspections
Control Equipment Visual Inspections
Yes No N\A No visible evidence of external leakage from piping and joints
Yes No N\A Floor Control Valve Assembly:
•Control valve open
•Pressure gauge present: Static pressure: .................
•Check valve present, if shown on drawings
•Inspector’s test and drain connection present
Yes No N\A Is typical ceiling Obstructed or Unobstructed (Unobstructed: NFPA 13, Section, 3.7: if structural members are
greater than 7 ½-feet apart or if less than 7 ½-feet apart beams and girders less than 4-inches deep).
Yes No N\A Sprinkler installation and piping in accordance with drawings including sprinkler spacing and sizing
Yes No N\A Sprinkler support/hangars:
•Is each pipe length supported and not welded to support?
•Is any other equipment supported from sprinkler pipe?
Yes No N\A If water is from a pond/lake/river or other open top raw source, are pendant sprinklers below ceilings on a
return bend
Yes No N\A If sprinkler below ceiling and pressure exceed 100 psi, are sprinklers retrained from upward movement
Yes No N\A Sprinklers free of paint/loading/dust
Yes No N\A Sprinklers in proper orientation
Yes No N\A Are all obstructions (storage and partitions) at least 18-inches below deflector (NFPA 13: 8.5.5.3)
Control Equipment Inspection Notes:

Functional testing (Typical for each floor/zone)

Yes No N\A Closure of Floor control valve provides trouble alarm
Yes No N\A Operation of inspector’s test valve provides alarm between 30 and 150 seconds of opening.
(Residual pressure: ........... )
Functional Testing Notes:

These fire safety testing & commissioning verification inspection guide

sheets have been developed by the Accord as a resource for fire safety
engineers and fire safety technicians performing fire detection and fire
protection systems work in RMG factories.
T&CV INSPECTION CHECKLIST
Factory:............................................................................................................ Accord ID: ........................................

Inspector(s): ..................................................................................................... Date of Inspection:............................

STANDPIPE SYSTEMS
Document Review
Yes No N\A Installation Certificate and Record of Completion is available and on-site
Yes No N\A Approved as-built drawings are available and on-site
Yes No N\A Product Information Sheets and Listing Information is available and on-site
Yes No N\A Does all the necessary equipment have third party listing certificates consistent with products on -site

Pre-Test Activities
Yes No N\A Factory staff has informed workers that testing activities will be conducted
Yes No N\A Contractor has proper testing tools and equipment

Inspections
Control Equipment Visual Inspections
Yes No N\A Are all control valves open (bottom of riser)
Yes No N\A Are there control valves on the fire hose valve piping; if so is the control valve electronically supervised
Yes No N\A Fire hose valves located in stairs and unobstructed
Yes No N\A Fire hose valves do not obstruct stairs
Yes No N\A Standpipes properly supported and not welded to supports
Yes No N\A Condition of hose new/without tears or rot
Yes No N\A Fire department hose valve gasket in place
Yes No N\A Pressure gauge present at top of standpipe riser: ........... Static Pressure

Functional testing
Yes No N\A Operate all hose valves for full range of motion (make sure all caps are in place and don’t leak)
Yes No N\A Flow top of riser hose valve, for full flow
Yes No N\A Pressure gauge at top or standpipe riser: ........... Residual Pressure when flowing
Inspection Notes:

These fire safety testing & commissioning verification inspection guide

sheets have been developed by the Accord as a resource for fire safety
engineers and fire safety technicians performing fire detection and fire
protection systems work in RMG factories.