Scribd
Upload
75 views3 pages

RC Slab Punching Shear Stresses Check & Calculation of Required Shear Reinforcement According To Aci 318M-11 Using Usr From Ramconcept To Csi Safe Programs

1. The document calculates punching shear stresses and required shear reinforcement for a slab according to ACI 318M-11. 2. It is found that the unreinforced shear stress ratio is 1.27, exceeding the shear capacity provided by concrete alone of 1.66 MPa. 3. Required shear reinforcement is calculated for rebar and headed studs, with actual shear reinforcement areas provided exceeding the minimum requirements in both cases.

Uploaded by

Prabhakaran
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
75 views3 pages

RC Slab Punching Shear Stresses Check & Calculation of Required Shear Reinforcement According To Aci 318M-11 Using Usr From Ramconcept To Csi Safe Programs

1. The document calculates punching shear stresses and required shear reinforcement for a slab according to ACI 318M-11. 2. It is found that the unreinforced shear stress ratio is 1.27, exceeding the shear capacity provided by concrete alone of 1.66 MPa. 3. Required shear reinforcement is calculated for rebar and headed studs, with actual shear reinforcement areas provided exceeding the minimum requirements in both cases.

Uploaded by

Prabhakaran
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
You are on page 1/ 3

RC Slab Punching Shear Stresses check & calculation of required shear reinforcement according to ACI rev 0.

0
318M-11 Using USR from RamConcept to CSI SAFE programs
Project :- Project Designed by:- M. Abu Shady
Building :- Building Checked by:- M. Abu Shady
Element:- Element Date:- 22-Sep-20
Location:- Location

1- General input:
Slab Thk t = 500 mm fy = 420 N/mm2
Clear cover = 35 mm fc' = 45 N/mm2
d = 455 mm fy stud= 345 N/mm2
Column Demensions Normal weight concrete λ = 1
c1 = 500 mm b_o= 1237 mm from RamConcept or CSI SAFE
c2 = 1000 mm Parallel to edge for edge column
Position Edge Column
ᵦ 2.00 ACI 11.11.2.1.a
αs 30 ACI 11.11.2.1.b

Unreinforced Stress Ratio from RamConcept or CSI SAFE USR=v_u/ 1.270 v_u= 2.11 MPa
(ϕv_c )=

2- The shear stress resistance provided by Concrete only:

ϕ_shea 0.75 ACI 9.3.2.3 & ACI 9.3.4.a


r
ϕv_c=min. of{■8(ϕ0.17(1+2/β)λ√( 〖 f′ 〗 _c ) = 1.71 MPa
@ϕ0.083 ((α_s d)/b_o +2) λ√( 〖 f′ 〗 _c )
@ϕ0.33λ√( 〖 f′ 〗 _c ))}
= 5.44 MPa ACI 318-11, Cl 11.11.2.1
= 1.66 MPa

Therefore, ϕv_c= 1.66 MPa Φvc < vu Use Shear reinforcement or drop panel
=

3- The maximum shear stress resistance provided by Concrete & shear reinforcement:

〖 ϕv 〗 _(n max) ={█(ϕ0.5√(f_c^′ ) with rebar shear reinforcement, ACI 318-11, Cl = 2.52 MPa APPLICABLE
11.11.3.2 @ϕ0.58√(f_c^′ ) with Steel I or C Shear heads, ACI 318-11, Cl 11.11.4.8
@ϕ0.66√(f_c^′ ) with Headed Shear stud "SSR", ACI 318-11, Cl 11.11.5.1 )} = 2.92 MPa APPLICABLE
= 3.32 MPa APPLICABLE

4- The maximum shear stress resistance provided by Concrete only in case of using shear reinforcement:

ϕv_(c with shear rft)={█(ϕ0.17√(f_c^′ ) with rebar shear reinforcement, ACI 318-11, Cl 11.11.3.2
@ϕ0.33√(f_c^′ ) with Steel I or C Shear heads, ACI 318-11, Cl 11.11.4.8 @ϕ0.25√(f_c^′ ) with = 0.86 MPa
Headed Shear stud "SSR", ACI 318-11, Cl 11.11.5.1 )} = 1.66 MPa
= 1.26 MPa

5- Calculating shear stress to be resisted by shear reinforcement:

v_s=v_u-ϕv_(c with shear rft)= {█( for rebar shear reinforcement@ = 1.25 MPa
forSteel I or C Shear heads@ forHeaded Shear stud "SSR")} = 0.45 MPa
= 0.85 MPa

ACI 318M-11 Punching shear reinforcement Page 1 of 3 M.A.S


RC Slab Punching Shear Stresses check & calculation of required shear reinforcement according to ACI rev 0.0
318M-11 Using USR from RamConcept to CSI SAFE programs
Project :- Project Designed by:- M. Abu Shady
Building :- Building Checked by:- M. Abu Shady
Element:- Element Date:- 22-Sep-20
Location:- Location

6- Calculating the required shear reinforcement:


a- For Rebar shear reinforcement
A_v=(v_s b_o
S)/ 〖 ϕf 〗 _y =369 mm2 ACI 318-11,Eq.11-15

For one peripheral line use 4 Leg T12 @75mm =452 mm2 OK, Av actual > Av required

b- For Headed shear Studs


A_v=(v_s b_o
S_stud)/ 〖 ϕf 〗 _( =264 mm2 ACI 318-11,Eq.11-15
y stud)
For one peripheral line use 3 Leg T12 @65mm =339 mm2 OK, Av actual > Av required
v_(s act)=(A_(v act)
1.092 MPa Ok, > ϕ0.17√(f_c^′ ) 0.86MPa ACI 318-11, CL 11.11.5.1
〖 ϕf 〗 _(y stud))/( b_o =
S_stud )

c- Determine distance a from sides of column where stirrups or studs may be terminated
a distance = 371 mm b_(o @ "Cut 3050mm v_(u @ "Cut 0.86 MPa
off" ) = off" )=

ACI 318M-11 Punching shear reinforcement Page 2 of 3 M.A.S


revision history
Rrev 0.1 Dated 2017-05-30
Correcting the message in Cell I53 for Stud reinforcement

You might also like