Renderoc SP40 constructive solutions

Shrinkage controlled, polymer modified, fibre

reinforced cementitious repair mortar, specifically
designed for spraying

Uses
Properties
Renderoc SP40 is suitable for wet spraying and hand applica- The following typical results were obtained at a water:powder
tion in a wide variety of repair applications, and is particularly ratio of 0.18.
well suited to vertical and overhead repairs. Typical applica-
tions would include, but not be limited to, the following: Test method Typical result
Mass infill to large areas Drying shrinkage to ASTM C 157-93
Repairs to irregular profiles 28 days : <1000 microstrain
Excellent for repairs to fire-damaged concrete
Fast track repair programmes, where rapid Flexural strength : >7 N/mm2 at 28 days
application at high volume is required (BS 6319 Pt.3)
Single layer, high build applications Tensile strength : >2.5 N/mm2 at 28 days
(BS 6319 Pt.7)
Advantages
Compressive strength : >20 Mpa at 1 day
Cost effective - shrinkage control enables repairs to be hand application
completed „right first time‟. Very low rebound is an additional (BS 1881 Pt.1161) : >45 Mpa at 28 days
cost benefit (iterative result, based
Enhanced durability - works in tandem with extremely upon spray application)
low permeability to prolong effective working life Note 1: 70mm cubes, air cured @ 25°C.
Compatibility - aligns performance closer than ever before, Design criteria
to that of host concrete
Attention to the basic design criteria given below should ensure
User friendly - specifically developed to provide an easy- that the full benefits of this technology are achieved :
to-apply product, suitable for local conditions
(i) Recommended limits for a single Spray/Trowel/Hand
Definable performance - positive benefits are easily application are:
demonstrated via a single, simple measurement
Minimum applied thickness : 10 mm
Description
Overhead sections : up to 150 mm thick*
Renderoc SP40 is supplied as a single component, ready to
use blend of dry powders and fibres which requires only the Vertical sections : up to 200 mm thick*
addition of clean water to produce a highly consistent, hand Surface area of a single repair : see ‘Note’
and spray grade, repair mortar suitable for most structural and
load bearing repairs. NOTE : The restricting factor on surface area will be the
practicality of maintaining a continuous application
Technical support
* built in layers of 10mm
Fosroc offers a comprehensive technical support service to
specifiers end users and contractors. Berger Fosroc is also (ii) In situations where a substrate/repair barrier is required,
able to offer on-site technical assistance, an AutoCAD facility or enhanced bond strength/working time is required, or where
and dedicted specification assistance in locations all over the the substrate is likely to be damp (e.g. seawalls, quays etc.),
world. Nitobond EP epoxy bonding agent should be used.

(iii) Water addition - between 4.25 & 4.5 litres per 25 kg bag
Under no circumstances should part bags be used or additional
water be employed. Either of these two actions will adversely
affect material performance, automatically invalidating Berger
Fosroc‟s standard product guarantee.

page 1 of 2
Renderoc SP40

Instructions for use Precautions

Renderoc SP40 should be mixed and applied in strict accord- Health & Safety
ance with the Product Method Statement, a copy of which may Renderoc SP40 contains cement powders which, when mixed
be obtained from your nearest Berger Fosroc office. with water or upon becoming damp, release alkalis which can
Estimating be harmful to the skin.

Supply During use, avoid inhalation of the dust and contact with the
skin or eyes. Wear suitable protective clothing - eye protec-
Renderoc SP40 : 25 kg bags tion, gloves and respiratory equipment (particularly in confined
Yield spaces).

Renderoc SP40 : approx 13.5 litres The use of barrier creams to provide additional skin protection is
(at water addition of 4.25ltr/bag) per 25kg bag also advised. In case of contact with the skin, rinse with plenty
of clean water, then cleanse thoroughly with soap and water.
Limitations
In case of contact with eyes, rinse immediately with plenty of
Renderoc SP40 should not be used when the ambient tempera- clean water and seek medical advice. If swallowed seek medical
ture is below 5°C and falling. attention immediately - do not induce vomiting.
Renderoc SP40 should not be part mixed, nor part bags used.

Renderoc SP40 should not be exposed to running water either

during application or prior to final set.

Storage
Fire
Shelf Life
Renderoc SP40, is non-flammable and thus presents no fire
Renderoc SP40 has a shelf life of 6 months if kept in a dry hazard.
environment, in its original packing. If stored in conditions of
high temperature and/or humidity, the shelf life may be reduced For further information, please refer to the Product Material
to as little as 4 months. Safety Data Sheet for Renderoc SP40.

Important note :
Fosroc products are guaranteed against defective materials and manufacture and are sold
subject to its standard terms and conditions of sale, copies of which may be obtained on
request. Whilst Fosroc endeavours to ensure that any advice, recommendation specification
or information it may give is accurate and correct, it cannot, because it has no direct or
continuous control over where or how its products are applied, accept any liability either
directly or indirectly arising from the use of its products whether or not in accordance with
Fosroc Chemicals any advice, specification, recommendation or information given by it.
(India) Pvt. Ltd.
Head Office telephone fax e-mail
Embassy Point, No. 150,
2nd Floor, Infantry Road, +91 80-42521900 +91 80-22281510 [email protected]
Bangalore 560 001,
Karnataka

Regional Offices

Chennai Mumbai Noida Kolkata

Hills Centre,Old No 5, MBC Park, 12th floor, Office No.12B, Unit No. 601, Highway Tower-II 304, Jodhpur Park
New No 9, 3rd Cross Street, ‘D’ Block, Near G Corp/Hyper City A-13/2, 6th Floor, Sector– 62 Kolkata 700 068
Jeth Nagar, Raja Annamalaipuram, Kasarwadawali, Ghodbunder Road, Gautam Buddha Nagar, Ph:+91 33-65343188
Chennai 600 028. Thane (West) 400 615 Noida 201 309, Uttar Pradesh Fax: 033-2499-0280
Ph: +91 44 61304500 Ph: +91 22 6229 6800 Ph: +91 120 6121900
Fax: 022 62296809 Fax: 0120-4270622

www.fosroc.com
page 2 of 2 INDIA/2020/0425/A