Volume 49, Number 1, 2015 ACTA TECHNICA NAPOCENSIS
Electronics and Telecommunications
________________________________________________________________________________
PREPARATION OF PAPERS FOR ACTA TEHNICA NAPOCENSIS
ELECTRONICS AND TELECOMMUNICATIONS
First A. AUTHOR , Second B. AUTHOR
Institution Name, Location (all on one line if possible)
Address, Phone and Fax Numbers, Email
Abstract: These instructions give you the basic guidelines for preparing camera-ready papers for Acta Tehnica Napocensis
Electronics and Telecommunications journal. Use computer desktop software with proportional fonts and several type
sizes. Define all symbols used in the paper. If you consider that the instructions are not clear enough, please do not hesitate
to contact the Publishing Committee for your questions (email: [email protected], http://users.utcluj.ro/~atn). Please
put your text through a spell-checker and ensure use of clear, accurate English. The abstract should not exceed 100 words,
on a single column.
Keywords: Acta Technica Napocensis, typing instructions, parts of text, upper case.
Manuscript received February 29, 2015; revised April 17, 2015
1
Volume 51, Number 1, 2010 ACTA TECHNICA NAPOCENSIS
Electronics and Telecommunications
________________________________________________________________________________
I. PAGE FORMAT 1
T
T 0
Prepare you camera-ready paper in full-size format, on I med i (t )dt
A4 (210 x 297 mm). The papers should include an even (1)
number of pages (4, 6 or 8), on one side of the sheet.
Quality white paper should be used. Multiplying will be Figures are to be accompanied by a caption (e.g.
carried out by 1:1 scale photocopying. Figure 1. This is an example of a figure.) using 10 pt,
In formatting your page, set the left margin to 2cm, italic. They should be numbered sequentially. A blank
the top margin on the first page to 5cm (on the other line should be inserted both before and after the figure.
pages to 3cm), the right margin to 2cm and the bottom
margin to 3cm. Authors are asked not to include any
header and not to number the pages. A laser printer
should be employed.
II. TYPE STYLES AND POINT SIZES
The text will include the following sequence of parts:
Title: 14 bold, all capitals, centered, close to the
upper margin, followed by a free line
Authors: first name (lower case), surname (upper Figure 1. This is an example of a figure.
case), centered, 11 pt.
Affiliation: 10 pt, italic, followed by 2 free lines All line drawings and photos should be in black and
Abstract: 9pt, bold, on 1 column white, unless color is specifically required. Smaller size
Keywords: 10 pt, italic, 1 column equations, tables, illustrations will be positioned within
The main text: 2 equal "balanced newspaper" the paragraphs; their width should not exceed that of the
columns, 0,5 cm between columns, 10pt. column. Large figures, tables, formulae can be inserted
References: 9 pt, numbered and written according on the whole width of the page, preferably at the
with IEEE standard. In the main text reference citations beginning or the end of the page.
will be indicated by arab digits between square brackets Physical quantities in the text should be typed italics
[1], [1, 3-6] too, e.g. in the explanations following the formulae.
The best results should be obtained if serif typeface Refer to all equations, tables and illustrations in the text.
such as TIMES NEW ROMAN or TIMES ROMAN Use only standard symbols and abbreviations unless
fonts are employed. Avoid sans serif typefaces such as defined when first used in the text. Be sure that all
Swiss or Helvetica. subscripts, superscript, Greek letters and mathematical
Titles headings will be centered on their column, will symbols are clearly identified.
be typed in all capital letters and numbered with Roman
numerals. They will be separated from the previous text
body by one free line. No free line will be left between REFERENCES
the title and following paragraph. A new paragraph [1] L. Chiariglione, "The Development of an Integrated
(tabs) should be indented by 0,5 cm. If your paper is Audiovisual Coding Standard: MPEG", IEEE Proceedings,
vol. 83, pp.151-157, 1995.
longer than the allowed page limit, you may shorten it [2] J.S. Lim, Two Dimensional Signal and Image Processing,
by using a slightly smaller type size for the main text or Prentice Hall International, Inc., New York, 1992.
by slightly reducing the space between lines. [3] George Altemosel, "Achieving Cell Balancing for Lithium-
Ion Batteries", Hearst Electronics Products, 2008. [Online].
III. EQUATION, TABLES Available: http://www2.electronicproducts.com/ [Accessed:
AND ILLUSTRATIONS May 1, 2010].
Equations, tables and figures will be included in the text
in the order of reference.
Equations are to be numbered sequentially with arab
normal digits between parentheses, placed at the right
end of the line. A blank line should be inserted both
before and after the equation.
