Scribd
Upload
339 views4 pages

Structural Design Standards

The document lists standards and references for structural design including Eurocodes for wind, snow, and thermal loading. It provides material properties for steel and glass. Loadings considered are wind per tunnel test, dead load, and load combinations from Eurocode. Permissible deflections are given for glass. Drawing references are listed but not included. Wind load reference drawings show positive and negative wind pressure distributions.

Uploaded by

Laurence Sarmiento
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
339 views4 pages

Structural Design Standards

The document lists standards and references for structural design including Eurocodes for wind, snow, and thermal loading. It provides material properties for steel and glass. Loadings considered are wind per tunnel test, dead load, and load combinations from Eurocode. Permissible deflections are given for glass. Drawing references are listed but not included. Wind load reference drawings show positive and negative wind pressure distributions.

Uploaded by

Laurence Sarmiento
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

 

1. STANDARDS & SOFTWARE REFERENCES  
 STANDARD REFERENCES  
 WIND, DEAD & LIVE LOADS  
o EN 1991‐1‐1:2002 (E)  
o Eurocode 1: Actions on structures ‐ Part 1‐1: General actions ‐Densities, self‐weight, 
imposed loads for buildings  
 EN 1991‐1‐3:2003 (E)  
o Eurocode 1: Actions on structures Part 1‐3 General actions ‐ Snow Loads  
 EN 1991‐1‐4:2005+A 1  
o Eurocode 1: Actions on structures ‐ Part 1‐4: General actions ‐ Wind actions  
 EN 1991‐1‐5: 2003 (E)  
o Eurocode 1: Actions on structures ‐ Part 1‐5: General actions – Thermal actions & 
Loading as per Wind Tunnel Test Report & Specifications (MPXDXB‐RFI‐000453) Mild 
Steel and Stainless Steel  
 BS EN 1990:2002+A1:2005  
o Eurocode ‐ Basis of structural design  
 BS EN‐1993‐1‐5: 2005  
o Design of steel structures ‐ Part 1‐1 General rules and rules for buildings  
 GLASS 
o ASTM E‐1300: 2004 Standard practice for determining load resistance of glass in 
buildings  
o AS 1288: 2006 Glass in buildings ‐ Selection & Installation  
 SOFTWARE REFERENCES  
o STRUCTURAL ANALYSIS 
o Staad Pro‐2007  
 ANCHOR BOLTS  
o Profis: 2.7.5 – Hilti Anchor  
 GLASS  
o SJ MEPLA 
2. MATERIAL PROPERTIES [BSEN 1999‐1‐1‐2007]  
Steel   S275 
Density ρal  78.5KN/m3 
Modulus of Elasticity, Eal  205000 MPa 
Minimum Tensile Strength, Fu  410 MPa 
Tensile Yield Strength, Fy  275 MPa 
 
Glass  ASTM E1300 
Density ρal  25KN/m3 
Modulus of Elasticity, Eg  70000 MPa 
Allowable stresses ‐ HS  36.5MPa 
Allowable stresses ‐ FT  73MPa 
   

4 

 
 

3. LOADINGS & PERMISSIBLE DEFLECTION  
 WIND LOAD  
Max Design Wind Pressure on wall, W ∶= ±2kPa As per wind tunnel test 
As per Specification (Refer attached references)  
 DEAD LOAD  
DL is calculated in their respective calculation pages of profiles as per the actual weights of   
profiles   
 LOAD COMBINATIONS AS EN 1990 (SHOWN IN REFERENCE)  
Services and ultimate combinations will be shown in the report.  
o Permissible Deflection  [As Per Specifications]  
Glass           L/90 OR 20mm      L=Shorter Span  
   

5 

 
 

4. DRAWING REFERENCES 

6 

 
 

WIND LOAD REFERENCE 
POSITIVE WIND LOAD 

 
 

NEGATIVE WIND LOAD 

 
 

   

7 

You might also like