Accessory Application Publication No.

MII 15736
INSTALLATION HANDGUARD After ‘15 Issue Date
P/N 08P70-MKA-D80 NC700X/XD, NC750X/XD
INSTRUCTIONS March 2016
Honda Dealer: Please give a copy of these instructions to your customer.
PARTS LIST TORQUE INFORMATION
Refer to the Service Manual for the torque values of the
(2) removed parts. Unless otherwise indicated, follow the
(12)
specified torque in the chart.
(3)

Item N·m kgf·m lbf·ft

6 mm socket bolt 10 1.0 7

INSTALLATION
(10)
(5) CAUTION
(6) • To prevent burns, allow the engine, exhaust system,
(11) radiator, etc. to cool before installing the accessory.
NOTE:
• These instructions are for the NC700XD model, but
other types are similar. If there are any differences,
(4)
eac h d if fere n c e w ill b e d e s c r i b e d in t h e se
(13)
(15) (8) instructions.
(9)
• Be sure the throttle opens smoothly and closes
(1)
(7) automatically in any steering position after installation
(14) of the right handguard.
• Reinstall the removed parts on the motorcycle and
make sure that the wires and harnesses are not
pinched.
No. Description Qty

(1) Installation Instruction URL 1

1. Remove the handlebar end weight, plug, and wire tie
as shown.
(2) Right handguard 1
• Repeat on the right side.
(3) Left handguard 1
(4) Handlebar end weight 2
(5) Right handguard stay 1 WIRE TIE
(6) Left handguard stay 1
(7) Socket bolt A (6 x 60 mm) 2
(8) Rubber washer 2
(9) Washer 2
(10) Socket bolt B (6 x 14 mm) 2
(11) Handguard band 2
(12) 6 mm cap nut 2 SCREW (Save)
(13) 6 mm U nut 2
HANDLEBAR
(14) Cable clip 1 END WEIGHT
(Save)
(15) Rubber mount 1
PLUG (Save)
TOOLS REQUIRED
Box-end wrench (10 mm)
Hex wrench (5 mm)
Scissors
Torque wrench

© 2016 American Honda Motor Co., Inc. - All Rights Reserved. 1 of 3 08P70-MKA-D80
2. Loosely install the handlebar end weight as shown. 4. Install the assembled left handguard as shown.
• Repeat on the right side. • Repeat on the right side.

ASSEMBLED LEFT
HANDLEBAR END WEIGHT HANDGUARD

RUBBER WASHER

WASHER
SOCKET BOLT A
(6 x 60 mm) ASSEMBLED LEFT
HANDGUARD
WASHER

Align.

RUBBER WASHER

3. Install the left handguard stay to the left handguard

as shown.
5. Install the handguard band as shown.
• Repeat on the right side.
• Repeat on the right side.
LEFT HANDGUARD STAY
HANDGUARD BAND
6 mm CAP NUT

LEFT HANDGUARD 6 mm U NUT

SOCKET BOLT B
(6 x 14 mm)

2 of 3
6. Install the wire tie as shown. 8. Perform the following for NC700XD model only:
Tighten the socket bolt A (6 x 60 mm). Cut the rubber mount and set it on the throttle
• Repeat on the right side. cables.
9. Install the rubber mount into the cable clip as shown.
10. Clamp the cable clip.

SOCKET BOLT A
(6 x 60 mm))

40 mm

WIRE TIE (Reuse)

7. Perform the following for NC700XD model only:

CABLE CLIP
Install the cable clip to the right handguard stay as RUBBER MOUNT
shown.

Clamp.

Cut.
THROTTLE CABLES

CABLE CLIP

3 of 3