Scribd
Upload
109 views1 page

Design of One Way Slab

The document summarizes the design of a one-way slab for a proposed two story residential building. It includes design parameters for the slab such as material strengths, dimensions, and design loads. It also shows the ductility requirements, moment diagram, and design result. The design result determined that 10 mm diameter reinforcement bars placed along the short side of the slab at 150 mm spacing would be sufficient to resist the bending moments.

Uploaded by

Andro Rebuyas
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
109 views1 page

Design of One Way Slab

The document summarizes the design of a one-way slab for a proposed two story residential building. It includes design parameters for the slab such as material strengths, dimensions, and design loads. It also shows the ductility requirements, moment diagram, and design result. The design result determined that 10 mm diameter reinforcement bars placed along the short side of the slab at 150 mm spacing would be sufficient to resist the bending moments.

Uploaded by

Andro Rebuyas
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

DESIGN OF SLAB (ONE-WAY)

ASpectrum Designs Plus Engineering Services Project Title: Proposed Two Storey Residential Building
Address: 8487 Sandoval Avenue, Pinagbuhatan, Pasig City 1602 Project Location: Lot 4 and 5 Block 1, Monte De Luna Subdivision, Ormoc City
Contact: 09982028893 Structural Engineer: Engr. Andro S Rebuyas, RCE, ME-1, RMP, M.Eng-SE
Gmail add: [email protected] Membership: M.PICE, M.ASCE, M.PAMEA, M.FPEA, M.PSUMP, M.NAMPAP, M.SEAD

DESIGN PARAMETERS AND DESIGN LOADS

DESIGN PARAMETERS DESIGN LOADS

f'c = 20.7 MPa Compressive strength of concrete LL = 1.90 KPa Live Load
fy = 275 MPa Yield strength of steel bar C= 0.20 KPa Ceiling
fb = 10 mm Bar diameter U= 0.10 KPa Utilities
t= 125 mm Thickness of slab T= 0.60 KPa Topping
L= 2.230 m Longer dimension of slab FF = 0.60 KPa Floor Finishing
B1 = 1.200 m Shorter dimension of slab MP = 0.50 KPa Movable Partition
s max = 450 Maximum spacing of reinforcement O= 0.00 KPa Others
b= 1000 mm-strip Width of slab S= 3.00 KPa Slab
d= 100 mm-strip Effective depth of slab
Total DL = 5.00 KPa

DUCTILITY REQUIREMENTS, MOMENT DIAGRAM AND DESIGN RESULT

DUCTILITY REQUIREMENTS MOMENT DIAGRAM

0.75 [ 510b1f'c ] (+) Mmax = 6.69 kN-m (+) Mmax = 6.69 kN-m
rmax =
fy(600 + fy)
= 0.02797
rmin = 1.4/fy
= 0.0051
0.5
rmin = (f'c) /4fy
= 0.0041 (-) Mmax = 6.53 kN-m
rmin = 0.0051 DESIGN RESULT
LENGTH
Mu = Øρfybd²(1-0.59ρfy/f’c)
150 mm - 10 mm diameter
(+) Mmax = 6.69 kN-m

r= 0.0025 < 0.0051 r = 0.005091 WIDTH


S= As/ρd = 154.1964 say = 150 mm 150 mm - 10 mm diameter

(-) Mmax = 6.53 kN-m

r= 0.0024 > 0.0051 r 0.0051


= govern Therefore, 10 mm diameter top bars along short side @ 150 mm spacing O.C.
S= As/ρd = 154.1964 say = 150 mm and 10 mm diameter bottom bars along short side @ 150 mm spacing O.C.

This Spreadsheets is licensed only to Engr. Andro S. Rebuyas, RCE, ME-1, RMP, M.Eng-SE

You might also like