We reserve all rights in this document and in the information contained therein.

Reproduction,use or disclosure to third parties without express authority is strictly forbidden.

© 2012 ABB

COMMISSIONING REPORT

Powerline Carrier Equipment: Series ETL600R4

Project : …………………………..

ABB Order N° : …………………………..

Station : …………………………..

Link : …………………………..

Equipment N° : …………………………..

Frequency : Tx = …………kHz Rx = …………kHz

Direction : …………………………..

Commissioning Report contains

ETL600 System Test Report Pages C1 to C15

HMI600 Printout of Configuration Pages ................

HMI600 Printout of Status Pages ................

Test ETL600 List of used Test-instruments Pages ................

………………………….. ………………………………… Pages ................

The tuning of the equipment is in accordance with the following instructions:

Programming and Testing of ETL600R4 1KHW002609-EN

Compatibility Requirements for ETL600 1KHW001490-EN
Tuning of ETL600R4 Rx RF Filter P4RX 1KHW002584-EN
Tuning of ETL600R4 Tx RF Filter on E5TH and E5TC 1KHW002585-EN
APLC Channel Equalization for ETL600 1KHW001494-EN
Firmware Download for ETL600R4 1KHW002589-EN
Technical Data ETL600R4 1KHW002590-EN

Rev. ind:
..

Type des. Part no.

No. of p.
Prep. Hans Benninger / PSND 2012-04-15 Doc.kind

Appr. M. Israel / PSND2 2012-05-15 Title Commissioning Report ETL600R4 15+

Resp.dept. PSNEX
Doc. no. Lang. Rev. ind. Page

ABB Switzerland Ltd 1KHW002587 en A C1

FILE: 1KHW002587AE Commissioning Report ETL600R4; TEMPLATE: TECHN_DOC_STAND_P.dot R0; SKELETON: ; SAVEDATE: 5/15/2012 11:55:00 AM
 Rev. ind.
Commissioning Report ETL600R4 Equipment HE

SAFETY INSTRUCTIONS

Please refer to chapter 2 of ETL600R4 instruction manual 1KHW002582.

Designations and abbreviations used:

Designation Meaning
___________ Measured value
[ ... ] Programmed value
[ ]D Preferred setting (default)
[X ] Test passed or jumper is set
[ ] Not tested or jumper is not set
B5LA Module type
BER Bit Error Ratio
Def. Default value
equ. Equipment
fLo Lower frequency, usually meant as low cut-off frequency
LED Light Emitting Diode found on the front panel
HMI600 User Interface Program for ETL600 running on a PC
N02, N08 Position in rack. Slot number N02, N08
Rx Receiver
Tx Transmitter
PC Personal Computer
(T.02/..1) Connector 1 of terminal block connected to board at rack position N02

Notes:
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
Sign Commissioning Eng.: Sign Witness Eng.:
Doc. no. Lang. Rev. ind. Page

ABB Switzerland Ltd 1KHW002587 en A C2

 Rev. ind.
Commissioning Report ETL600R4 Equipment HE

REVISION

Rev. Page (p.) Description Date

ind. Chapter (c.) Dept./Init.
A c. C.2 Measurement at MCB 2012-05-15 / Be

Notes:
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
Sign Commissioning Eng.: Sign Witness Eng.:
Doc. no. Lang. Rev. ind. Page

ABB Switzerland Ltd 1KHW002587 en A C3

 Rev. ind.
Commissioning Report ETL600R4 Equipment HE

Test Permissible Test

No. Test procedure Test point value Units result

C.1. General

C.1.1 Checking the line of communication

Line attenuation dB [ ]
Return loss Ar dB [ ]

C.1.2 Visual checks

Proper wiring of protective earth P7LH, P7LP, P7LQ PE wired [ ]
Proper wiring of protective earth Cubicle PE wired [ ]
Proper wiring of power supply P7LH, P7LP, P7LQ polarity ok [ ]
If the positive pole (+) of the battery is Cubicle supply terminals [ ]
grounded, place an earth jumper to the
positive pole (+) of the cubicle supply

C.2. Check power supply B5LD Left Right

C.2.1 Battery supply 48V DC MCB -46 to –56 V DC [ ] [ ]D

C.2.2 Ripple on 48V DC MCB <1 V rms [ ] [ ]D
C.2.3 Green LED B5LD front panel Lit [ ] [ ]D

C.3. Upload configuration [ ]

C.4. Change configuration, if necessary [ ]

C.4.1 Reducing output power, if necessary

Determine Ar min = minimal value of Ar as Ar min= dB
measured in C.1.1 _____________
Calculate output power reduction Ared: Ared = dB
No reduction, if Ar min  12 dB: _____________
Ared = max(0, (3 - Ar min / 4 ))
Decrease Max. power PEP by Ared HMI600: [ ]
Configuration / System /
Channel settings /
Max. power (PEP)
Store configuration to flash HMI600: Equipment / [ ]
Store configuration to
FLASH

Notes:
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
Sign Commissioning Eng.: Sign Witness Eng.:
Doc. no. Lang. Rev. ind. Page

ABB Switzerland Ltd 1KHW002587 en A C4

 Rev. ind.
Commissioning Report ETL600R4 Equipment HE

Test Permissible Test

No. Test procedure Test point value Units result

C.5. Transmitter

C.5.1 Adjust Tx RF level

Dialog box Adjust Tx RF level: [ ]
Click Select and then Start
Mark if the Tx level is not [ ]
measured
Measured Tx level is within tolerance RF LINE MONITOR or Permissible [ ]
RF LINE socket at E5TH range indicated
front panel in dialog box

C.5.2 Adjust Tx alarm level

Dialog box: Adjust Tx alarm level
Follow the instructions given in the dialog [ ]
box
Tx ALARM indication: E5TH and - in case of LED(s) to be ON [ ]
ETL600-100 – E5TC
State of HW alarm relay after programmed Pins 2-3 of V9OT cable Closed [ ]
delay.
Turn  potentiometer(s) TX-LVL-AL LED(s) to be [ ]
ADJUST on P1LP till TX-LVL-AL LED(s) OFF
go(es) off.
Tx alarm indication E5TH and - in case of LED(s) to be [ ]
ETL600-100 – E5TC OFF
State of HW alarm relay after programmed Pins 2-3 of V9OT cable Open [ ]
delay.
Click OK.

C.6. Receiver

C.6.1 Adjust Rx RF level

Menu: Equipment Commissioning and
maintenance, dialog box: Adjust Rx RF
level
Follow the instructions in the dialog box
Line attenuation Dialog box __________ dB
Increase of receive level (due to parallel Dialog box
PLC links) __________ dB
Adjustment performed [ ]

C.6.2 Connect RF cable and set alarm

thresholds 1
Alarm thresholds set (Menu: Dialog box [ ]
Configuration / System / Alarm settings)

1
If the remote equipment is operational
Notes:
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
Sign Commissioning Eng.: Sign Witness Eng.:
Doc. no. Lang. Rev. ind. Page

ABB Switzerland Ltd 1KHW002587 en A C5

 Rev. ind.
Commissioning Report ETL600R4 Equipment HE

Test Permissible Test

No. Test procedure Test point value Units result

C.6.3 Check link alarms

Link alarm of the local equipment Alarm status of the local No local link [ ]
equipment alarm
Link alarm of the remote equipment No remote link [ ]
alarm

C.6.4 Tune hybrid on E5TH

RF Coaxial cable to be connected.
Dialog box: Tune RF hybrid Dialog box Till minimum is [ ]
Press 'Start measurement' & adjust the read by HMI.
balancing network (Resistance with jumper
R0 … R4 and potentiometer R1101,
inductance with jumper L0 … L17 and
capacitance with jumpers C1 to C17)
Ch 1 Ch 2 Ch 3
C.6.5 SNR pilot Mark if not configured: [ ] [ ] [ ]
Upload status data of local equipment
SNR pilot HMI600 > 15 dB [ ] [ ] [ ]

C.7. Equalization

Ch 1 Ch 2 Ch 3
C.7.1 Measure frequency response Mark if not configured: [ ] [ ] [ ]

In menu Equipment / Commissioning and HMI600 [ ] [ ] [ ]

maintenance / Frequency response /
APLC channel 1, APLC channel 2 or
APLC channel 3
Ch 1 Ch 2 Ch 3
C.7.2 Select Equalizer Mark if not configured: [ ] [ ] [ ]

In menu Equipment / Commissioning and HMI600 [ ] [ ] [ ]

maintenance / Select equalizer / APLC
channel 1, APLC channel 2 or
APLC channel 3

C.8. R1BC, if present Mark if not configured: [ ]

Activate alarms as programmed on R1BC. Corresponding N/C Closed [ ]

contacts on R1BC.
Deactivate alarms as programmed on Corresponding N/C Open [ ]
R1BC. contacts on R1BC.

C.9. Configure Real time Clock (RTC)

C.9.1 Setting real time clock

Menu: Equipment, Commissioning and
maintenance, Eventrecorder, Set clock
Download date/time to RTC Dialog box Actual time and [ ]
date

Notes:
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
Sign Commissioning Eng.: Sign Witness Eng.:
Doc. no. Lang. Rev. ind. Page

ABB Switzerland Ltd 1KHW002587 en A C6

 Rev. ind.
Commissioning Report ETL600R4 Equipment HE

Test Permissible Test

No. Test procedure Test point value Units result

C.9.2 Test external real time clock

synchronization, if available
Menu: Equipment, Commissioning and
maintenance, Eventrecorder, Set clock
Download date/time to RTC Dialog box Wrong time
Upload date/time from RTC Dialog box Correct time [ ]

Test Permissible Test

No. Test procedure Test point value Units result

C.10. NSD600 / G4AI, if present

TPE1 TPE2
C.10.1 NSD600 loop test Mark if not configured: [ ] [ ]

Check Actual transmission

time TLink HMI600 < 2*T0 ms _______ _______
Menu: Equipment,
Commissioning and
maintenance, NSD600 send
loop test

C.10.2 Command transmission

time

TPE1 TPE2
Command A Mark if not configured: [ ] [ ]
Terminal: Refer HMI600
Tx command A (T71/1) – (T71/2) [ ] Mean value
(T…/...) – (T.../…) [ ]
 T0 ms ________ ________
Rx command A (T71/9) – (T71/10) [ ]
(T…/...) – (T.../…) [ ]
TPE1 TPE2
Command B Mark if not configured: [ ] [ ]
Terminal: Refer HMI600
Tx command B (T71/3) – (T71/4) [ ] Mean value
(T…/...) – (T.../…) [ ] ms
 T0 ________ ________
Rx command B (T71/11) – (T71/12) [ ]
(T…/...) – (T.../…) [ ]
TPE1 TPE2
Command C Mark if not configured: [ ] [ ]
Terminal: Refer HMI600
Tx command C (T71/5) – (T71/6) [ ] Mean value
(T…/...) – (T.../…) [ ] ms
 T0 ________ ________
Rx command C (T71/13) – (T71/14) [ ]
(T…/...) – (T.../…) [ ]

Notes:
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
Sign Commissioning Eng.: Sign Witness Eng.:
Doc. no. Lang. Rev. ind. Page

ABB Switzerland Ltd 1KHW002587 en A C7

 Rev. ind.
Commissioning Report ETL600R4 Equipment HE

Test Permissible Test

No. Test procedure Test point value Units result

TPE1 TPE2
Command D Mark if not configured: [ ] [ ]
Terminal: Refer HMI600
Tx command D (T71/7) – (T71/8) [ ] Mean value
(T…/...) – (T.../…) [ ] ms
 T0 ________ ________
Rx command D (T71/15) – (T71/16) [ ]
(T…/...) – (T.../…) [ ]

C.10.3 Reset counters Mark if not configured: [ ]

Menu: Equipment, HMI600 All counters = 0 [ ]
Commissioning and
maintenance, Eventrecorder,
Reset counter, OK:

C.11. Testing of O4LE

N02 N08 N14

C.11.1 Service Phone. Mark if not configured: N24 N30 N48
[ ] [ ] [ ]
Pick up the phone and talk. Service phone, at front Own voice is audible N02 N08 N14
panel without feedback or N24 N30 N48
excessive echo [ ] [ ] [ ]
N02 N08 N14
C.11.2 Hot line direct phone Mark if not configured: N24 N30 N48
[ ] [ ] [ ]
Measure voltage at open loop 43 V … 52 V V DC
condition N02/N24: ___________

N08/N30: ___________

N14/N48: ___________
Pick up the phone and talk Direct telephone Own voice is audible N02 N08 N14
without feedback or N24 N30 N48
excessive echo [ ] [ ] [ ]
N02 N08 N14
C.11.3 Remote subscriber Mark if not configured: N24 N30 N48
[ ] [ ] [ ]
Measure voltage at open loop 43 V … 52 V V DC
condition N02/N24: ___________

N08/N30: ___________

N14/N48: ___________
Pick up the phone and talk Suscriber telephone Own voice is audible N02 N08 N14
without feedback or N24 N30 N48
excessive echo [ ] [ ] [ ]

Notes:
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
Sign Commissioning Eng.: Sign Witness Eng.:
Doc. no. Lang. Rev. ind. Page

ABB Switzerland Ltd 1KHW002587 en A C8

 Rev. ind.
Commissioning Report ETL600R4 Equipment HE

Test Permissible Test

No. Test procedure Test point value Units result

N02 N08 N14

C.11.4 Pax 2-wire Mark if not configured: N24 N30 N48
[ ] [ ] [ ]
PAX-BLOCKING normal Measure at terminal 6a-6b is open N02 N08 N14
telephony 6a-6b, 6b-7a 6b-7a is closed N24 N30 N48
[ ] [ ] [ ]
PAX-BLOCKING blocked Measure at terminal 6a-6b is closed N02 N08 N14
Interrupt local loop, wait about telephony 6a-6b, 6b-7a 6b-7a is open N24 N30 N48
30 sec. [ ] [ ] [ ]
N02 N08 N14
C.11.5 Pax 4-wire Mark if not configured: N24 N30 N48
[ ] [ ] [ ]
Test E-Wire: Terminal telephony 3a-3b E-Wire must toggle N02 N08 N14
Close and open M-wire at N24 N30 N48
terminal telephony 4a-4b [ ] [ ] [ ]
Measure Output level. Feed into terminal Configured Output dBm N02 N08 N14
Feed 800 Hz with configured telephony 1a-1b level ±1 dB (600 ) N24 N30 N48
input level of Pax Measure at terminal (Def.: -3.5 dBm) [ ] [ ] [ ]
(Default: -3.5 dBm). telephony 2a-2b
(Activate at terminal telephony
4a-4b)
PAX-BLOCKING normal Measure at terminal 6a-6b is open N02 N08 N14
telephony 6a-6b, 6b-7a 6b-7a is closed N24 N30 N48
[ ] [ ] [ ]
PAX-BLOCKING blocked Measure at terminal 6a-6b is closed N02 N08 N14
Interrupt local loop, wait about telephony 6a-6b, 6b-7a 6b-7a is open N24 N30 N48
30 sec. [ ] [ ] [ ]

N02 N08 N14

C.11.6 Pax 4/2-wire Mark if not configured: N24 N30 N48
[ ] [ ] [ ]
Test E-Wire: Terminal telephony 3a-3b E-Wire must toggle N02 N08 N14
Close and open M-wire at N24 N30 N48
terminal telephony 4a-4b [ ] [ ] [ ]
Measure Output level at AF1. Feed into terminal Configured Output dBm N02 N08 N14
Feed 800 Hz with configured telephony 1a-1b level ±1 dB (600 ) N24 N30 N48
input level (Def.: -3.5 dBm). Measure at terminal (Def.: -3.5 dBm) [ ] [ ] [ ]
(Activate at terminal telephony telephony 2a-2b
4a-4b)
Measure Output level at Feed into terminal Configured Output dBm N02 N08 N14
PAX2W. telephony 1a-1b level ±1 dB (600 ) N24 N30 N48
Feed 800 Hz with configured Measure at terminal (Def.: -7.0 dBm) [ ] [ ] [ ]
input level (Def.: -3.5 dBm). telephony 8a-8b
(Activate at terminal telephony
4a-4b)

Notes:
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
Sign Commissioning Eng.: Sign Witness Eng.:
Doc. no. Lang. Rev. ind. Page

ABB Switzerland Ltd 1KHW002587 en A C9

 Rev. ind.
Commissioning Report ETL600R4 Equipment HE

Test Permissible Test

No. Test procedure Test point value Units result
Test Local/Transit: Feed into terminal Configured Output dBm N02 N08 N14
Measure Output level at AF1. telephony 1a-1b level – 40 dB or (600 ) N24 N30 N48
Feed 800 Hz with configured Measure at terminal lower [ ] [ ] [ ]
input level of PAX2W (Def: telephony 8a-8b
-0.0 dBm).
Activate at terminals telephony
5a-4b and 4a-4b.
PAX-BLOCKING normal Measure at terminal 6a-6b is open N02 N08 N14
telephony 6a-6b, 6b-7a 6b-7a is closed N24 N30 N48
[ ] [ ] [ ]
PAX-BLOCKING blocked Measure at terminal 6a-6b is closed N02 N08 N14
Interrupt local loop, wait about telephony 6a-6b, 6b-7a 6b-7a is open N24 N30 N48
30 sec. [ ] [ ] [ ]
N02 N08 N14
C.11.7 Transit mode for E&M wire Mark if not configured: N24 N30 N48
[ ] [ ] [ ]
Test E-Wire: Terminal telephony 3a-3b E-Wire must toggle N02 N08 N14
Close and open M-wire at N24 N30 N48
terminal telephony 4a-4b [ ] [ ] [ ]

C.11.8 Testing the teleoperation

ports

N02 N08 N14 N20

C.11.9 Teleoperation AF1, if not Mark if not configured:
N24 N30 N42 N48 N54
used for telephony
[ ] [ ] [ ] [ ] [ ]

Fed input level, [dBm], Expected Output Measured Output level at

@ 800 Hz at AF1-IN level at AF1-OUT AF1-OUT
N02/N24: ___________±1 Feed into terminal N02/N24: ______±1 dBm N02/N24: ___________
telephony 1a-1b (600 )
N08/N30: ___________±1 N08/N30: ______±1 N08/N30: ___________
Measure at terminal
N14/N42: ___________±1 telephony 2a-2b N14/N42: ______±1 N14/N42: ___________
N20/N48: ___________±1 Ext. Boost not active. N20/N48: ______±1 N20/N48: ___________
N54: ___________±1 N54: ______±1 N54: ___________

N02 N08 N14 N20

C.11.10 Teleoperation AF2 Mark if not configured:
N24 N30 N42 N48 N54
[ ] [ ] [ ] [ ] [ ]

Fed input level, [dBm], Expected Output Measured Output level at

@ 800 Hz at AF2-IN of level at AF2-OUT AF2-OUT
remote.
N02/N24: ___________±1 Feed into terminal teleop. N02/N24: ______±1 dBm N02/N24: ___________
3a-3b (600 )
N08/N30: ___________±1 N08/N30: ______±1 N08/N30: ___________
Measure at terminal
N14/N42: ___________±1 teleop. 4a-4b N14/N42: ______±1 N14/N42: ___________
N20/N48: ___________±1 ext. Boost not active. N20/N48: ______±1 N20/N48: ___________
N54: ___________±1 N54: ______±1 N54: ___________

Notes:
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
Sign Commissioning Eng.: Sign Witness Eng.:
Doc. no. Lang. Rev. ind. Page

ABB Switzerland Ltd 1KHW002587 en A C10

 Rev. ind.
Commissioning Report ETL600R4 Equipment HE

Test Permissible Test

No. Test procedure Test point value Units result

C.11.11 Teleoperation AF3 Mark if not configured: N02 N08 N14 N20
N24 N30 N42 N48 N54
[ ] [ ] [ ] [ ] [ ]

Fed input level, [dBm], Expected Output Measured Output level at

@ 800 Hz at AF3-IN of level at AF3-OUT AF3-OUT
remote.
N02/N24: ___________±1 Feed into terminal teleop. N02/N24: ______±1 dBm N02/N24: ___________
5a-5b (600 )
N08/N30: ___________±1 N08/N30: ______±1 N08/N30: ___________
Measure at terminal
N14/N42: ___________±1 teleop. 6a-6b N14/N42: ______±1 N14/N42: ___________
N20/N48: ___________±1 ext. Boost not active. N20/N48: ______±1 N20/N48: ___________
N54: ___________±1 N54: ______±1 N54: ___________

N02 N08 N14 N20

C.11.12 Teleoperation AF4 Mark if not configured:
N24 N30 N42 N48 N54
[ ] [ ] [ ] [ ] [ ]

Fed input level, [dBm], Expected Output Measured Output level at

@ 800 Hz at AF4-IN of level at AF4-OUT AF4-OUT
remote.
N02/N24: ___________±1 Feed into terminal teleop. N02/N24: ______±1 dBm N02/N24: ___________
7a-7b (600 )
N08/N30: ___________±1 N08/N30: ______±1 N08/N30: ___________
Measure at terminal
N14/N42: ___________±1 teleop. 8a-8b N14/N42: ______±1 N14/N42: ___________
N20/N48: ___________±1 ext. Boost not active. N20/N48: ______±1 N20/N48: ___________
N54: ___________±1 N54: ______±1 N54: ___________

N02 N08 N14

C.11.13 Teleoperation AF4 used for Mark if not configured: N24 N30 N48
ext. teleprotection [ ] [ ] [ ]
Test EXT-BOOST: Activate at terminal
teleop. 9a-9b

Fed input level, [dBm], Feed into terminal teleop. Expected Output Measured Output level at
@ 800 Hz at AF4-IN 7a-7b level at AF4-OUT AF4-OUT
N02/N24: ___________±1 Measure at terminal N02/N24: ______±1 dBm N02/N24: ___________
teleop. 8a-8b (600 )
N08/N30: ___________±1 N08/N30: ______±1 N08/N30: ___________
N14/N48: ___________±1 N14/N48: ______±1 N14/N48: ___________

C.12. V.11 ports

C.12.1 V.11 Port 1 Mark if not configured: [ ]

-5
BER test Front plate P4LT/V/X, BER ≤ 10 [ ]
V.11 PORT 1 during ____ sec

C.12.2 V.11 Port 2 Mark if not configured: [ ]

BER test Front plate P4LX, BER ≤ 10-5 [ ]
V.11 PORT 2 during ____ sec

Notes:
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
Sign Commissioning Eng.: Sign Witness Eng.:
Doc. no. Lang. Rev. ind. Page

ABB Switzerland Ltd 1KHW002587 en A C11

 Rev. ind.
Commissioning Report ETL600R4 Equipment HE

Test Permissible Test

No. Test procedure Test point value Units result

C.13. V.24 ports

C.13.1 V.24 Port 1 Mark if not configured: [ ]

BER test Front plate P4LT/V/X, BER ≤ 10-5 [ ]
V.24 PORT 1 during ____ sec

C.13.2 V.24 Port 2 Mark if not configured: [ ]

BER test Front plate P4LT/V/X, BER ≤ 10-5 [ ]
V.24 PORT 2 during ____ sec

C.13.3 V.24 Port 3 Mark if not configured: [ ]

BER test Front plate P4LX, BER ≤ 10-5 [ ]
V.24 PORT 3 during ____ sec

C.13.4 V.24 Port 4 Mark if not configured: [ ]

BER test Front plate P4LX, BER ≤ 10-5 [ ]
V.24 PORT 4 during ____ sec

C.14. Testing of LAN port

C.14.1 LAN Port 1 Mark if not configured: [ ]

Test of throughput Front plate P4LV/X, Throughput
LAN PORT 1 during ______ sec _____ __________________
% errored or missing frames of Front plate P4LV/X, ≤ 0.5% errored or
[ ]D 10’000 LAN PORT 1 missing 128-byte [ ]
frames during
[ ] ……………..
transmitted frames. ___________ sec

C.14.2 LAN Port 2 Mark if not configured: [ ]

Test of throughput Front plate P4LV/X, Throughput
LAN PORT 2 during ______ sec _____ __________________
% errored or missing frames of Front plate P4LV/X, ≤ 0.5% errored or
[ ]D 10’000 LAN PORT 2 missing 128-byte [ ]
frames during
[ ] ……………..
transmitted frames. ___________ sec

C.14.3 LAN Port 3 Mark if not configured: [ ]

Test of throughput Front plate P4LV/X, Throughput
LAN PORT 3 during ______ sec _____ __________________
% errored or missing frames of Front plate P4LV/X, ≤ 0.5% errored or
[ ]D 10’000 LAN PORT 3 missing 128-byte [ ]
frames during
[ ] ……………..
transmitted frames. ___________ sec

Notes:
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
Sign Commissioning Eng.: Sign Witness Eng.:
Doc. no. Lang. Rev. ind. Page

ABB Switzerland Ltd 1KHW002587 en A C12

 Rev. ind.
Commissioning Report ETL600R4 Equipment HE

Test Permissible Test

No. Test procedure Test point value Units result

C.14.4 LAN Port 4 Mark if not configured: [ ]

Test of throughput Front plate P4LV/X, Throughput
LAN PORT 4 during ______ sec _____ __________________
% errored or missing frames of Front plate P4LV/X, ≤ 0.5% errored or
[ ]D 10’000 LAN PORT 4 missing 128-byte [ ]
frames during
[ ] ……………..
transmitted frames. ___________ sec

C.14.5 HMI over LAN

Test of connectivity Front plate P4LU/V/X, Connected [ ]
LAN PORT ____

C.15. Testing of O4CV

C.15.1 Slot positions of O4CV

boards
Record slot positions of O4CV Refer to HMI600
boards configuration view O4CV#1: N_____

O4CV#2: N_____

O4CV#3: N_____

O4CV#4: N_____

C.15.2 Service Phone Mark if not configured: [ ]

Pick up the phone and talk. Service phone, at front Own voice is audible [ ]
panel of O4CV#1 without feedback or
excessive echo

C.15.3 Hot line direct phone Mark if not configured: [ ]

Measure voltage at open loop Terminals 7a-7b, 8a-8b, 40.8 V … 55.2 V O4CV#1: O4CV#2:
condition 9a-9b, 0a-0b of term.bl.2 P1 P2 P3 P4 P1 P2 P3P4
for ports P1, P2, P3, P4 [ ] [ ] [ ] [ ] [ ] [ ] [ ][ ]
O4CV#3: O4CV#4:
P1 P2 P3 P4 P1 P2 P3P4
[ ] [ ] [ ] [ ] [ ] [ ] [ ][ ]
Pick up the phone and talk Direct telephone at Own voice is audible O4CV#1: O4CV#2:
terminals 7a-7b, 8a-8b, without feedback or P1 P2 P3 P4 P1 P2 P3P4
9a-9b, 0a-0b of term.bl.2 excessive echo [ ] [ ] [ ] [ ] [ ] [ ] [ ][ ]
for ports P1, P2, P3, P4
O4CV#3: O4CV#4:
P1 P2 P3 P4 P1 P2 P3P4
[ ] [ ] [ ] [ ] [ ] [ ] [ ][ ]

Notes:
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
Sign Commissioning Eng.: Sign Witness Eng.:
Doc. no. Lang. Rev. ind. Page

ABB Switzerland Ltd 1KHW002587 en A C13

 Rev. ind.
Commissioning Report ETL600R4 Equipment HE

Test Permissible Test

No. Test procedure Test point value Units result

C.15.4 Remote subscriber Mark if not configured: [ ]

Measure voltage at open loop Terminals 7a-7b, 8a-8b, 40.8 V … 55.2 V O4CV#1: O4CV#2:
condition 9a-9b, 0a-0b of term.bl.2 P1 P2 P3 P4 P1 P2 P3P4
for ports P1, P2, P3, P4 [ ] [ ] [ ] [ ] [ ] [ ] [ ][ ]
O4CV#3: O4CV#4:
P1 P2 P3 P4 P1 P2 P3P4
[ ] [ ] [ ] [ ] [ ] [ ] [ ][ ]
Pick up the phone and talk Direct telephone at Own voice is audible O4CV#1: O4CV#2:
terminals 7a-7b, 8a-8b, without feedback or P1 P2 P3 P4 P1 P2 P3P4
9a-9b, 0a-0b of term.bl.2 excessive echo [ ] [ ] [ ] [ ] [ ] [ ] [ ][ ]
for ports P1, P2, P3, P4 O4CV#3: O4CV#4:
P1 P2 P3 P4 P1 P2 P3P4
[ ] [ ] [ ] [ ] [ ] [ ] [ ][ ]
O4CV#1: O4CV#2:
C.15.5 Pax 2-wire Mark if configured: P1 P2 P3 P4 P1 P2 P3P4
[ ] [ ] [ ] [ ] [ ] [ ] [ ][ ]
O4CV#3: O4CV#4:
P1 P2 P3 P4 P1 P2 P3P4
[ ] [ ] [ ] [ ] [ ] [ ] [ ][ ]

C.15.6 Pax 4-wire Mark if not configured: [ ]

Test E-Wire: Terminals 3a-3b, 7a-7b E-Wire must toggle O4CV#1: O4CV#2:
of term.bl.1 for ports P1, P1 P2 P3 P4 P1 P2 P3P4
Close and open M-Wire at
P2 or 1a-1b, 5a-5b of [ ] [ ] [ ] [ ] [ ] [ ] [ ][ ]
terminals 4a-4b, 8a-8b of
term.bl.2 for ports P3, P4 O4CV#3: O4CV#4:
term.bl.1 for ports P1, P2 or
2a-2b, 6a-6b of term.bl.2 for P1 P2 P3 P4 P1 P2 P3P4
ports P3, P4 [ ] [ ] [ ] [ ] [ ] [ ] [ ][ ]
Measure output level. Feed into terminals Configured output dBm O4CV#1: O4CV#2:
Feed 800 Hz with configured
1a-1b, 5a-5b, 9a-9b of level ±5 dB (600 ) P1 P2 P3 P4 P1 P2 P3P4
term.bl.1 for ports P1, (Def.: -3.5 dBm) [ ] [ ] [ ] [ ] [ ] [ ] [ ][ ]
input level of remote PAX
P2, P3 or 3a-3b of
(Def.: -3.5 dBm). O4CV#3: O4CV#4:
term.bl.2 for port P4
P1 P2 P3 P4 P1 P2 P3P4
(Activate at terminals 4a-4b,
Measure at terminals [ ] [ ] [ ] [ ] [ ] [ ] [ ][ ]
8a-8b of term.bl.1 for ports P1,
2a-2b, 6a-6b, 0a-0b of
P2 or 2a-2b, 6a-6b of term.bl.2
term.bl.1 for ports P1,
for ports P3, P4)
P2, P3 or 4a-4b of
term.bl.2 for port P4

C.16. Manual reset [ ]

C.17. Documentation

If possible, take printout of [ ]

Configuration data for
reference.
Save the 'et6' file on disk with [ ]
Serial No. of ETL coded in
the file name, e.g.
‘HE400327C.et6’.

Notes:
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
Sign Commissioning Eng.: Sign Witness Eng.:
Doc. no. Lang. Rev. ind. Page

ABB Switzerland Ltd 1KHW002587 en A C14

 Rev. ind.
Commissioning Report ETL600R4 Equipment HE

Pending Items List:

Issue Description

YES NO YES NO
Commissioning Approved:   Exceptions Noted:  

Name PSNP3
of responsible
Signature &
Date
Company ABB Switzerland Ltd Consultant Customer

Doc. no. Lang. Rev. ind. Page

ABB Switzerland Ltd 1KHW002587 en A C15