BAB 1: PENGURUSAN DATA PELAN UKUR

Clean up pelan ukur

Fail latihan: HPB_ACAD_ORIGINAL SURVEY.dwg.

ARAHAN:

1. Delete tittle block. Select dan delete 5. Taip mapclean > enter > next > delete
keyboard. duplicates.
2. Pastikan semua layer aktif (On, tidak Check semua kotak untuk cleanup
freeze, dan tidak lock). parameter > next > finish.
3. Taip ‘PU’ enter. Purge All Item. 6. Taip ‘REA’ dan simpan fail sebagai
4. Taip -PU > enter > regapps > * > enter > 02_ACAD_Pelan Ukur Cleaned.
N > enter.

[1] [2] [3]

1
[3] [4]

[5]

[5]

[5]

2
BAB 2: FOLDER DAN PROJEK SETTING

Install templat Civil 3D

Fail latihan: jkrCv19_Template C3D.

ARAHAN:

1. Folder latihan > 02 Coursework > 02

Hospital Latihan_Folder dan Projek
Templat > 01_Data > 06 Template > copy
fail.
2. Workspace C3D > RC > Option > File tab
> template settting > Default Template
File Name for QNEW > browse > paste
fail > jkrCv19_Template C3D > open >
Ok.

[1]

[2]

3
Install geolocation
Fail latihan: Category.CSD
: Coordsys.CSD

ARAHAN:

1. Folder latihan > 02 Coursework > 02 3. Launch C3D > Toolspace > setting tab >
Hospital Latihan_Folder dan Projek Drawing Tittle > RC > Edit drawing Setting
Templat > 01 Data > 04 Coordinate Unit and zone tab > Drawing Unit > Meters
System > Copy kedua- dua fail. > Scale > 1:1000 > Custom scale > 1000 >
2. OS ( C:) > Program Data > Autodesk > categories > Malaysia > Available
Geospatial Coordinate Systems 14.05 > Coordinate systems > Perak > Ok
paste fail > continue.

[1]

[2]

[3]

4
[3]

5
Install fail design criteria
Fail latihan: __Road Engineering Association of Malaysia REAM_REVISED
: Arahan Teknik JKR 8_86_REVISED

ARAHAN:

1. Folder latihan > 02 Coursework > 02 3. Launch C3D > Alignment > Alignment
Hospital Latihan_Folder dan Projek Creation Tools > design Criteria Tab >
Templat > 01_Data > 05 design Criteria check use criteria- based design > browse
Editor > Copy kedua- dua fail. > fail yang telah di paste tadi telah ada.
2. OS ( C:) > Program Data > Autodesk > (checking)
C3D 2019 > enu > Data > Corridor
Design Standards > Metric > paste fail

[1]

[2]

6
Create folder data shortcut
Fail latihan: 02 Hospital Latihan_Folder dan Projek Templat

ARAHAN:

1. Buka fail baru > Toolspace > Prospector 2. C3D workspace > Data Shortcut > RC .
> Data Shortcut > RC > Set working New Data Shortcuts Project Folder > Name
Folder > Folder latihan > 02 Coursework > 02_WIP > Ok.
> 02 Hospital Latihan_Folder dan Projek 3. 02 Hospital Latihan_Folder dan Projek
Templat > Ok Templat > 02_WIP (checking)

[1] [1]

[2]

7
Create project template
Fail latihan:

ARAHAN:

1. Buka fail baru > Application menu > 2. Save As fail pada folder > Folder latihan >
Drawing utilities > Drawing Setting > Unit 02 Coursework > > 02 Hospital
and zone tab > Drawing Unit > meters > Latihan_Folder dan Projek Templat >
scale > 1:1000 > Categories > Malaysia > 02_WIP > name > C3D19_WIP_F1_00_TP
Available Coordinate systems > Perak > > Save.
Ok. 3. 02 Coursework > > 02 Hospital
Latihan_Folder dan Projek Templat >
02_WIP > C3D19_WIP_F1_00_TP
(Checking)

[1]

8
[2]

[3]

9
Create folder management
Fail latihan:

ARAHAN:

1. Folder latihan > 02 Coursework > 02

Hospital Latihan_Folder dan Projek
Templat > Create New Folder >
03_SHARED > Create New Folder >
04_PUBLISH > Create New Folder >
05_ARCHIVED

[1]

10
BAB 3: PERMODELAN TAPAK SEDIA ADA

Create surface
Fail latihan: C3D19_WIP_F1_01EG.dwg.

ARAHAN:

1. Folder latihan > 02 Coursework > 03 10. Prospector tab > Surface > 01EG_ 01_
Hospital Latihan_Permodelan Tapak Tapak Sedia Ada > Definition > Drawing
Sedia Ada > 02_WIP > Copy projek Objects > RC > Add > Object type > text >
templat > Paste pada tempat yang sama OK > Select all text > enter.
> rename > C3D19_WIP_F1_01EG. 11. Prospector tab > Surface > 01EG_ 01_
2. Buka perisan C3D > buka fail Tapak Sedia Ada > Definition > Edit > RC
C3D19_WIP_F1_01EG. > delete line > F Enter > buat garis
3. Toolspace > Prospector > Data Shortcut > pemisah > enter > klik surface > object
RC > Set working Folder > Folder latihan viewer.
> 02 Coursework > 03 Hospital 12. Rc > Isolate object > end object selection
Latihan_Permodelan Tapak Sedia Ada > > save as > > 03 Hospital
Ok Latihan_Permodelan Tapak Sedia Ada >
4. Insert tab > panel block > insert > more 03_SHARE >
option >browser > folder 03 Hospital jkrCv19_1_(BMhpB1_19_001)_F1_eg00_(
Latihan_Permodelan Tapak Sedia Ada > s)_190101.
01_Data > 02 ACAD_Pelan Ukur Cleaned 13. Prospector tab >> surface > 01EG_ 01_
> Open Tapak Sedia Ada > RC > Surface
5. Insertion point > Uncheck specify on - properties > Information tab > Surface
screen > Scale > X : 1000 > Check style > 04_Contours 1m and 5m > Drop
uniform scale > Block unit > unit > mm > down image > Edit current selection >
Factor 0.001> check explode > ok Contours tab > Expand Contour interval >
6. ZE > Enter > Click 2 point nombor (satu minor interval > 0.1 > major interval > 0.5
ada il satu lagi tiada) > Rc > Select similar > apply > Ok > save fail.
> isolated selected object. 14. Application menu > export > Export Civil
7. RC > Find > Find what > il > replace with 3D drawing > Export to file type >
> 0 > replace all > 158 object > done > AutoCAD DWG > Destination Folder > 03
close box. Hospital Latihan_Permodelan Tapak
8. Modify tab > surface > surface tools Sedia Ada > 03_SHARE >Destination file
panels > move to surface > move text to name profix > ACAD_ > File to export >
elevation > select text > 760 text > enter.

11
9. Prospector tab >> surface > RC > create pilih fail model sahaja > Export > Tutup
surface > name > 01EG_ 01_ Tapak dialog box > save file.
Sedia Ada > style > 03 Triangles > render 15. Buka fail latihan > 03 Hospital
> by block> ok. Latihan_Permodelan Tapak Sedia Ada >
Check semua kotak untuk cleanup buang perkataan ‘model pada nama fail.
parameter > next > finish.

[1]

[2]

12
[4]

[5]

13
[6]

[7]

14
[8]

[9]

15
[10]

[11]

16
[13]

17
[14]

[15]

18
BAB 4A: PERMODELAN REKABENTUK KONSEP

Grading
Fail latihan: C3D19_WIP_F1_01EG.dwg.

ARAHAN:

1. Folder latihan > 02 Coursework > 04 7. Create polyline > home tab > draw panel >
Hospital Latihan_Permodelan polyline > pick first point > sambungkan
Rekabentuk Konsep > 02_WIP > Copy semua bucu platform.
projek templat C3D19_WIP_F1_00TP > 8. Home tab > create design panel > feature
Paste pada tempat yang sama > rename line.> create feature line from object > click
> C3D19_WIP_F1_02EW. polyline yg buat td > enter> name >
2. Buka perisan C3D > buka fail 02EW_Site 1_PL3.00m_tekan butang
C3D19_WIP_F1_01EG. segitiga > Property field > next counter >
3. Prospector Tab > Data Shortcut > RC> insert >number style > 01,02,03,.. >
Set Working Folder > Folder Latihan > 04 Starting number > 1 > increment value > 1
Hospital Latihan_Permodelan > ok > check erase existing entities >
Rekabentuk Konsep > OK check assign elevations > ok >Assign
4. PROSPECTOR TAB > Data shortcut > elevations > 3 > ok
RC> create data shortcut > Check box 9. Home tab > create design panel > grading
01EG_ 01_ Tapak Sedia Ada > Ok > > grading creation tools > set the grading
Tutup fail. tool >edit name template > starting number
5. Buka fail C3D19_WIP_F1_02EW > > 1 > increment number > 1 > ok > ok.
prospector tab > data shortcut > surface 10. Set the target surface > Select surface
>01EG_ 01_ Tapak Sedia Ada > RC >01EG_ 01_ Tapak Sedia Ada > ok
>create reference > style > 02 Border >Select a grading criteria > grade to
only > ok > ze surfaces > create grading > select feature
6. Taip xref > attach drawing > 04 Hospital line > select side > klik pada bahagian luar
Latihan_Permodelan Rekabentuk Konsep feature line > yes . slope > enter > slope >
> 01_Data > 03 ARCHITECT DRAWING enter> 2 :1 > enter > esc
> open > Check locate using geographic
Data > ok lukisan arikitek dh ada

19
[3]

[4]

20
[5] [7]

[8]

21
[10]

22
BAB 4B: PERMODELAN REKABENTUK KONSEP

Create platform surface

Fail latihan: C3D19_WIP_F1_01EG.dwg.

ARAHAN:

1. Prospector > surface> RC > Create 8. Surface > turn off surface >
Surface > Name > 02EW_01_PL3.00m > 02EW_01_PL3.00m > style > 01 no display
style > 04 Contours 1m and 5m > ok. 9. Analyze tab >volumn dashboard > create
2. Expand surface > 02EW_01_PL3.00m > new volume surface > name > 02EW_03_
definiton > add breakline > mid ordinate Pengiraan kerja Tanaga > style > no display
distance > 0.01> ok > pilih feature line di > render > By block > base surface >
luar dan di dalam > enter 01EG_01_Tapak Sedia Ada > comparism
3. RC > object viewer surface > 02EW_02_Rekabentuk Konsep >
4. 02EW_01_PL3.00m > RC > Surface ok > ok
properties > surface style > triangles > ok 10. Generate cut n fill report> print as pdf > save
5. Edit > delete line > f> enter > buat fail di 04 Hospital Latihan_Permodelan
garisan pada bhagian tapak yang ingin Rekabentuk Konsep > 03_SHARE >
dibuang > enter > esc jkrCv19_1_(BMhpB1_19_001)_F1_Laporan
6. Prospector > surface> RC > Create Kerja Tanah Konsep > save
Surface > name > 02EW_02_Rekabentuk 11. C3D > save as > 04 Hospital
Konsep > style > triangle > ok > ok. Latihan_Permodelan Rekabentuk >
7. 02EW_02_Rekabentuk Konsep > 03_SHARE >
definiton > edit > paste surface > jkrCv19_1_(BMhpB1_19_001)_F1_ew00_(s)
01EG_01_Tapak Sedia Ada > ok > edit > _190101 > save > close drawing.
RC > paste surface > 02EW_01_PL3.00m
> ok > klik surface > object viewer.

23
[2]

[5]

[7]

[8]
24
[9]

[10]

25
BAB 5A: PERMODELAN REKABENTUK AWALAN

Rekabentuk awalan
Fail latihan: C3D19_WIP_F1_02EW.dwg.

ARAHAN:

1. Buka perisian C3D > Open file > 05 6. Select a grading criteria > Grade to
Hospital Latihan_Permodelan elevation > Create grading > Select the
Rekabentuk Awalan > 02_WIP > feature > klik feature line > select the
C3D19_WIP_F1_02EW. grading side > klik tgh kolam > apply to
2. Toolspace >Prospector tab > data entire length > yes > grade to elevation > 0
shortcut > RC > Set working folder > 05 > cut format > slope > cut slope > 1.5 >
Hospital Latihan_Permodelan fill format > slope > Fill slope > 2:1 > Enter
Rekabentuk Awalan > Ok. > Esc. Buat langkah yang sama untuk
3. Home Tab > draw panel > polyline > lukis kolam kedua.
polyline pada keliling kolam > lakukan yg 7. Toolspace > Prospector tab > surface > RC
sama pada kedua2 kolam > Esc. > create surface > name >
4. Home tab > create design panel > feature 02EW_04_Kolam Tadahan > Style > 03
line > create feature line from object > Triangles > ok.
pilih kedua2 polyline kolam > Enter > 8. Expand 02EW_04_Kolam Tadahan>
name > 02EW_Site1_ Kolam Tadahan_ Definition . Breaklines > RC > Add > mid-
> next counter > insert > number style ordinate distance > 0.010m > ok > Klik
01,02,03,.. > starting number > 1 > feature line yg di luar dan di dalam (buat
increment value >1 > Ok > Check assign pada kedua –dua kolam > enter.
elevation dan check erase existing 9. Pilih surface kolam > RC > Isolate
entities > Ok > Elevation > 3m > Ok. selected object > prospector tab >
5. Home tab > create design panel > 02EW_04_Kolam Tadahan > definition >
grading > grading creation tools > set the edit > RC > delete line > F > enter > buat 1
grading group > group name > create a garis melintasi surface tersebut > enter >
grading group > name > click to edit enter.
name template > starting number > 2 > 10. RC > end object isolation > prospector tab
Increment value > 1 > klik ok untuk > select surface > RC > Rebuild -
semua dialog box Automatic. (Rebuild automatic untuk
semua surface)

26
[1]

[2]

27
[3]

[4]

[5]

28
[6] [8]

[9] [10]

29
BAB 5B: PERMODELAN REKABENTUK AWALAN

Rekabentuk awalan
Fail latihan: C3D19_WIP_F1_02EW.dwg.

ARAHAN:

1. Home tab >Create design panel > 9. Home tab >Create design panel >
assembly > create assembly > name > assembly > create assembly >
02EW_01_Simpang Masuk_ROW 02EW_03_Simpang Masuk_ROW Kerb
Lengkap > OK > Klik pada mana2 ruang Kanan > Ok> Klik Pada workspace
kosong. 10. Tool pallete > generic >
2. Tool pallete > Generic tab > LinkWidthAndSlope > Properties > Side >
LinkWidthAndSlope. Right > Slope > 0 > Klik pada subassembly
3. Properties > side > right > Slope > 0 > klik 11. Properties > Side > left > width > 1.5 >
pada assembly > buat perkara yang slope > 0 > Klik pada subassembly
sama pada bahu jalan sebelah kiri. 12. Tool palette > daylight > DaylightMaxWidth
4. Gunakan jenis subassembly yang sama > > Properties > cut slope > 1.5 : 1 > Fill
side > right > width > 1.5m > klik pada Slope > 2.00 :1 > klik pada bulatan sebelah
bulatan hujung subassembly > buat kiri subassembly.
perkara yang sama pada bahu jalan 13. Home tab >Create design panel >
sebelah kiri. assembly > create assembly >
5. Tool pallete > daylight > 02EW_04_Simpang Masuk_ROW Kerb Kiri
DaylightMaxWidth > > Ok > klik pada workspace.
6. Properties > side > right > cut slope > 1.5 14. Select kiri subassembly
:1 > Fill slope > 2.0 : 1 > klik pada bulatan 02EW_03_Simpang Masuk_ROW Kerb
hujung kedua- dua subassembly Kanan > modify subassembly panel >
7. Home tab >Create design panel > mirror > Klik pada subassembly
assembly > create assembly > 02EW_04_Simpang Masuk_ROW Kerb Kiri
02EW_02_Simpang Masuk_ROW Kiri > > Esc
Ok> Klik Pada workspace 15. Pilih kanan subassembly
8. Pilih semua subassembly bahagian kiri 02EW_03_Simpang Masuk_ROW Kerb
02EW_01_Simpang Masuk_ROW Kanan > modify subassembly panel >
Lengkap > copy > klik pada subassembly mirror > Klik pada subassembly
> 02EW_02_Simpang Masuk_ROW Kiri 02EW_04_Simpang Masuk_ROW Kerb Kiri
> Esc . (akan ada 4 subassembly)

30
[3]

[4]

31
 [6]

[8] [10]

[11] [12]

[14] [15]

32
[15]

33
BAB 5C: PERMODELAN REKABENTUK AWALAN

Corridor
Fail latihan: C3D19_WIP_F1_02EW

ARAHAN:

1. Taip Xref > enter > 03 ARCHITECT 5. Slope or Elevation Target > Klik
DRAWING > RC > Detach. LinkWidthAndSlope Right (baris paling
2. Home tab > create design panel > atas) Select alignment >
corridor > name > 02EW_01_Simpang 03RD_OFF_02_Jalan Sedia Ada_Right >
Masuk > Corridor style > 01 JKR General Select profiles > 03RD_OFF_01_Jalan
Corridor > Alignment > Sedia Ada_Right -2.500 > add > ok
03RD_CL_01_Jalan Sedia Ada > Profile 6. Slope or Elevation Target > Klik
> Rekabentuk > assembly > LinkWidthAndSlope Left (baris ketiga) >
02EW_01_Simpang Masuk_ROW Select alignment > 03RD_OFF_01_Jalan
Lengkap > Target surface > Sedia Ada_Left > Select profiles >
02EW_02_Rekabentuk Konsep 03RD_OFF_01_Jalan Sedia Ada_Left -
>Uncheck set baseline and region 5.000 > add > ok >Ok > rebuild
parameters > ok. 7. Klik corridor > modify panel > split region >
3. Prospector tab > Expand corridor > klik 2 kali pada garisan tgh jalan > esc
02EW_01_Simpang Masuk > RC > 8. Klik curve pada jalan keluar . klik corridor >
Properties > Parameter tab > Klik pada klik symbol 3 segi > Tarik sebelah kiri >
ruangan target > width or offset targets > buat yang sama pada sebelah kanan
Klik LinkWidthAndSlope Right (pilih yang 9. Prospector tab > corridor
di atas) > Select alignment > >02EW_01_Simpang Masuk > rc >
03RD_OFF_02_Jalan sedia ada_Right > properties > parameter tab > pilih RG-
Add > ok 02EW_01_Simpang Masuk_ROW Lengkap
4. Width or offset targets > Klik (baris atas) > rc > insert region – after >
LinkWidthAndSlope Left (pilih yang di assembly > 02EW_02_Simpang
atas) Select alignment > Masuk_ROW kiri> OK
03RD_OFF_01_Jalan sedia ada_Left > 10. Region yang baru (tengah) > klik pada
Add > ok frequency > expand horizontal baseline >
along tangents > 1 > curve increment > 1 >
along spiral > 1 > expand vertival baseline
> along vertical curves > 1 > ok

34
11. Klik pada region RG - 17. Target > Target surface >
02EW_02_Simpang Masuk_ROW Kiri - 02EW_02_Rekabentuk Konsep > ok>
(3) > klik pada target > Target surface > width or offset targets > Offset target (pilih
02EW_02_Rekabentuk Konsep > ok> yang paling bawah) > select alignment >
width or offset targets > Offset target (pilih 03RD_CL_01_Jalan Sedia ada > Add > ok
yang paling atas) > select alignment > > slope or elevation target > Target Profile
03RD_OFF_01_Jalan Sedia ada_Left > (pilih yang paling bawah) > Select
Add > ok > slope or elevation target > Alignment > 03RD_CL_01_Jalan Sedia
Target Profile (pilih yang paling atas) > Ada > Select profiles > Rekabentuk >Add >
Select Alignment > 03RD_OFF_01_Jalan ok > ok. > Rebuild.
Sedia Ada_Left > Select profile > 18. Pilih 02EW_04_simpang Masuk_ROW
03RD_OFF_01_Jalan Sedia Ada_Left . Kerb Kiri > RC > Insert Region – After >
Add > ok > ok > rebuild. Assembly > 02EW_04_Simpang Masuk_
12. Klik corridor > RC > corridor properties > ROW Kerb Kiri > ok
parameters > Add baseline > alignment > 19. RG - 02EW_04_Simpang Masuk_ROW
03RD_CR_01_ Jalan masuk Kiri > ok Kerb Kiri - (5) > Frequency > expand
13. Vertical baseline > select profile > horizontal baseline > along tangent > 1 >
03RD_CR_01_jalan Masuk Kiri > ok curve increment 1 > along spiral > 1 >
14. Klik 03RD_CR_01_Jalan Masuk Kiri > RC expand vertival baseline > along vertical
> add region > assembly > curves > 1 > ok
02EW_04_Simpang Masuk_ROW Kerb 20. Target > Target surface >
Kiri > ok. 02EW_02_Rekabentuk Konsep > ok>
15. Expand 03RD_CR_01_Jalan Masuk Kiri width or offset targets > Offset target (pilih
> End station > klik pada imej >klik pada yang paling bawah) > select alignment >
persimpangan 2 alignment > enter. 03RD_CL_02_Jalan Masuk Utama > Add >
16. 02EW_04_Simpang Masuk_ROW Kerb ok > slope or elevation target > Target
Kiri > Frequency > expand horizontal Profile (pilih yang paling bawah) > Select
baseline > along tangent > 1 > curve Alignment > 03RD_CL_02_Jalan Masuk
increment 1 > along spiral > 1 > expand Utama > Select profiles > Rekabentuk
vertival baseline > along vertical curves > >Add > ok > ok > ok > rebuild.
1 > ok 21. Ulang langkah 12 sehingga 17 untuk
sbelah kanan.
22. RG - 02EW_03_Simpang Masuk_ROW
Kerb Kanan - (6) > insert region – after >
Assembly > 02EW_03_Simpang
Masuk_ROW Kerb Kanan.

35
23. RG - 02EW_03_Simpang Masuk_ROW 30. Start station > klik pada tengah jalan msuk
Kerb Kanan - (7) > Frequency > expand > 24.90m > end station > 34.90m
horizontal baseline > along tangent > 1 > 31. Frequency > expand horizontal baseline >
curve increment 1 > along spiral > 1 > along tangent > 1 > curve increment 1 >
expand vertival baseline > along vertical along spiral > 1 > expand vertival baseline
curves > 1 > ok > along vertical curves > 1 > ok
24. Target > Target surface > 32. Target > surface > 02EW_02_Rekabentuk
02EW_02_Rekabentuk Konsep > ok> Konsep > ok > Width or offset targets >
width or offset targets > Offset target (pilih Offset target (pilih yang paling atas) >
yang paling atas) > select alignment > select alignment > 03RD_OFF_04_Jalan
03RD_CL_02_Jalan Masuk Utama > Add Masuk_Right > Add > ok > Offset target
> ok > slope or elevation target > Target (pilih pada baris ke empat dari atas) >
Profile (pilih yang paling atas) > Select select alignment > 03RD_OFF_03_Jalan
Alignment > 03RD_CL_02_Jalan Masuk Masuk_Left > Add > ok > slope or elevation
Utama > Select profiles > Rekabentuk target > Target Profile (pilih yang paling
>Add > ok > ok > ok > rebuild. (Abaikan atas) > Select Alignment >
Panorama) 03RD_OFF_04_Jalan Masuk_Right >
25. Klik corridor > Rc > object Viewer Select profiles > 03RD_OFF_04_Jalan
26. Buat adjust pada corridor jalan msuk Masuk_Right – 3.000 >Add > ok > ok > ok
(guna icon segi tiga) > rebuild > slope or elevation target >
27. Prospector tab > Corridor > Target Profile (pilih pada baris ketiga) >
02EW_01_simpang Masuk > RC > Select Alignment > 03RD_OFF_03_Jalan
properties > add baseline > alignment > masuk_left > Select profiles >
03RD_CL_02_jalan Masuk Utama > ok 03RD_OFF_03_Jalan masuk_left-3.00 >
28. Vertical baseline > Select a profile > Add > ok > ok >ok > rebuild.
rekabentuk 1 > ok 33. Klik corridor > RC > object viewer
29. Pilih 03RD_CL_02_Jalan Masuk Utama -
(6) > Rc > Add region > Assembly >
02EW_01_Simpang Masuk_ROW
Lengkap > ok

36
[2] [3]

37
[4] [6]

[6]

38
[7]

[8]

39
[11]

40
[15]

[17]

41
[20]

42
[24]

[25]

43
[26] [29]

[33]

44
BAB 5D: PERMODELAN REKABENTUK AWALAN

Paste surface
Fail latihan: C3D19_WIP_F1_02EW

ARAHAN:

1. Klik Corridor > RC > corridor properties 5. . Prospector tab> klik surface > tukar
>surface tab > klik create corridor surface semua surface style kepada no display
> rename > 02EW_05_ Simpang Masuk kecuali 02EW_06_Rekabentuk Awalan
> surface style > 03 triangles > ok> Data 6. Prospector tab > surface >
type > Links > specify code > Top > Add 02EW_06_Rekabentuk Awalan > Definition
(butang +) > Check add as breakline > > Edit > RC > paste surface >
Overhang correction > top Links > ok > 02EW_02_Rekabentuk Konsep > ok > Edit
Rebuild the corridor. > RC > paste surface > 02EW_04_Kolam
2. Prospector tab > surface > Tadahan > Ok > Edit > RC > paste surface
02EW_05_Simpang Masuk > RC > select > 02EW_05_Simpang Masuk > Ok > Klik
>RC > Isolated Selected Object. surface > RC > Object Viewer
3. Expand surface 02EW_05_Simpang 7. Save as > Folder 05 Hospital
Masuk > definition > edit > delete line > Latihan_Permodelan Rekabentuk Awalan >
taip F > Enter > buang garisan yang tidak 03_SHARE >
digunakan > RC > End object isolation. jkrCv19_2_(BMhpB1_19_001)_F1_
4. Prospector tab > surface> RC > Create ew00_(s)_190101
Surface > name > 02EW_06_Rekabentuk
Awalan > Ok.

45
 [3]

[5] [6]

46
BAB 6A&B: PERMODELAN REKABENTUK TERPERINCI

Cipta tapak
Fail latihan: C3D19_WIP_F1_01EG.dwg.

ARAHAN:

1. Buka fail > Folder latihan > 02 Coursework > 10. Station 9.85 > elevation tukar kepada 2.283
06 Hospital Latihan_Permodelan > Station 17.65 > elevation tukar kepada
Rekabentuk Terperinci > 02_WIP > 2.598 > close box > RC > end isolated
C3D19_WIP_F1_02EW object.
2. Toolspace >Prospector tab > data shortcut > 11. Home tab > create design panel > Feature
RC > Set working folder > 06 Hospital line > create feature line from object > klik
Latihan_Permodelan Rekabentuk Terperinci polyline (luar) > name >
> Ok. 02EW_Site1_Parking2 > check erase
3. Taip Xref > attach drawing > 03 existing entities and assign elevation >
ARCHITECT DRAWING > Open> Check assign elevation > from surface >
Locate using Geographic data > ok 02EW_06_Rekabentuk Awalan > check
4. Home tab > draw panel > polyline > 1st insert intermediate grade break points > ok.
center until 4st center > esc 12. Prospector tab > surface > RC > create
5. Home tab > modify panel > offset > 0.001 > surface > name > 02EW_07_ Parking > ok
enter > offset ke luar > esc. 13. Prospector tab > surface > 02EW_07_
6. Klik polyline bahagian dalam > Prospector Parking > definition > breaklines > RC > add
tab > surface > 02EW_06_Rekabentuk > Description > Parking > mid- ordinate
Awalan > RC > Select > isolate selected distance > 0.010m > select object > pilih
object. kedua-dua feature line > enter
7. Home tab > create design panel > Feature 14. Prospector tab > surface > Style > tukar
line > create feature line from object > klik semua style surface kepada no display
polyline > enter. kecuali 02EW_07_ Parking > Klik surface
8. Name > 02EW_Site1_Parking1 > check parking > RC > object viewer.
erase existing entities and assign elevation > 15. Prospector tab > surface > 02EW_07_
ok > from surface > 02EW_06_Rekabentuk Parking > definition > edit > swap edge > klik
Awalan > check insert intermediate grade 1 garis > klik feature line > object viewer.
break points > ok 16. Prospector tab > surface > RC > create
9. Klik feature line > Edit elevations panel > surface > name > 02EW_08_ Rekabentuk
Elevation editor > Delete elevation point Terperinci > ok
2.47, 3.40, 4.56, 6.21, 7.78, 14.68, 19.84.

47
17. Prospector tab > surface > 02EW_08_
Rekabentuk Terperinci > definition > Edit >
Paste surface > 02EW_06_Rekabentuk
Awalan >edit > Paste surface > 02EW_07_
Parking > ok > Klik surface > object viewer.

[4]

48
[6]

[8]

[10]

49
[15]

[17]

50
BAB 6C: PERMODELAN REKABENTUK TERPERINCI

Retaining wall
Fail latihan: C3D19_WIP_F1_02EW.dwg.

ARAHAN:

1. Home tab > create design panel > assembly 4. Start station > klik pada station 1.55 > end
> create assembly > name > station 21.45.
02EW_05_Tembok Penahan > ok > Klik 5. Frequency > Horizontal Baseline > along
pada workspace. tangents > 0.1 > curve increment > 0.1 >
2. Tool Pallete > retaining wall tab > along spirals > 0.1 > vertical baseline >
RetainWallVertical > Properties > side > right along vertical curves >0.1.
> Wall top width > 0.300 > Top Height > 0 > 6. Target surface > 01EG_01_Tapak Sedia
Key > no > klik pada assembly Ada > ok > rebuild > RC > Object Viewer.
3. Home tab > create design panel > corridor >
create corridor > name > 02EW_02_Tembok
Penahan > Baseline type > Feature Line >
Site > Site 1 > Feature Line >
02EW_Site1_Parking1 > Assembly >
02EW_05_Tembok Penahan > Target
Surface > 01EG_01_Tapak Sedia Ada >
check Set baseline and region parameters >
ok

[2]

51
[3]

[4]

52
[5]

[6]

53
BAB 6D & E : PERMODELAN REKABENTUK TERPERINCI

Sample line & pengiraan kerja tanah

Fail latihan: C3D19_WIP_F1_02EW.dwg.

ARAHAN:

1. Buka fail C3D19_WIP_F1_02EW.dwg > 7. Prospector tab > alignment > centerline
Home tab > create design panel > alignment alignment > 02EW_CL_Keratan Melintang
> alignment creation tools > name > > expand > sample line group > expand >
EW02_CL_01_Keratan Melintang >General Keratan Melintang > sample line > Tukar
tab > Alignment style > 04 Miscellaneous nama sample line kepada A,B,C,D,E,F,G,
Alignment > Alignment label set > 01 No dan H > enter
Label Set. 8. Analyze Tab > volume and materials panel
2. Alignment layout tools > Draw tangent – > Compute material > select alignment >
tangent (no curve) > buat 1 alignment 02EW_CL_01_Keratan Melintang > Select
merentasi surface sample line group > Keratan Melintang >
3. Home tab > profile & section view > sample ok.
lines > klik alignment > name > Keratan 9. Compute Materials – Keratan Melintang
Melintang > sample line style > 02 Earthwork dialog box > Quantity takeoff criteria > 01
> sample line label style > 02 Earthwork Cut and Fill > EG > 01EG_01_Tapak Sedia
Select data sources to sample > Check Ada > datum > 02EW_08_Rekabentuk
01EG_01_Tapak sedia Ada > Check Terperinci > ok.
02EW_08_Rekabentuk Terperinci > ok 10. Analyze Tab > volume and material panel
4. Sample line creation method > By range of > Volume report > ok >yes > yes.
station > Left swath width > width > 0m > 11. Save as pdf > M.L.Kerja Tanah
Right swath width > width > 250m > ok > L2_23.05.2019 > 02 Coursework > 06
enter Hospital Latihan_Permodelan Rekabentuk
5. Delete sample line on top (sbb xkna surface Terperinci > 03_SHARE >
sgt) jkrCv19_1_(BMhpB1_19-001)_F1_Laporan
6. Pendekkan sample line depan blkg Kerja Tanah Terperinci > save.

54
[1] [2]

[3]

55
[4] [7]

[9]

56
BAB 6F: PERMODELAN REKABENTUK TERPERINCI

Section view
Fail latihan: C3D19_WIP_F1_02EW.dwg.

ARAHAN:

1. Buka fail C3D19_WIP_F1_02EW.dwg > 5. Data Bands > select band set > 02
Home tab >profile & section view panel > Earthwork Band Set > Set Band properties
section view> create multiple view. > 01 existing band > surface1 >
2. General > select alignment > 01EG_01_Tapak Sedia Ada > surface2 >
02EW_CL_01_Keratan Melintang > Section 01EG_01_Tapak sedia Ada > 03 distance
view name > click to edit name template > band > surface1 > 01EG_01_Tapak Sedia
[Section View Station] >< [Next Counter] > Ada > surface2 > 01EG_01_Tapak sedia
Starting number > 1 > ok > section view style Ada > Next
> 01 Earthwork > next. 6. Section View Tables > select table style >
3. Section placement > Production > 02 EW Section Volume > add > X offset >
jkrCv18_Section Template C3D > Open > A1 5 > create section views.
Section 1 to 1000 > ok > next > next > next
4. Section display options >01EG_01_Tapak
Sedia ada > style > 01 existing ground >
02EW_08_Rekabentuk Terperinci > style >
02 Finished Ground > Next.

57
[2]

58
[3]

[4]

59
[5]

[6]
60
BAB 7A: PENYEDIAAN LUKISAN

Grading
Fail latihan: C3D19_WIP_F1_01EG.dwg.

ARAHAN:

1. Buka fail > Folder latihan > 02 Coursework > 7. Assign elevation > from surface >
07 Hospital Latihan_Penyediaan Lukisan > 02EW_08_Rekabentuk Terperinci >ok
02_WIP > C3D19_WIP_F1_02EW 8. Grading > grading creation tools > set the
2. Toolspace >Prospector tab > data shortcut > grading group > create a grading group >
RC > Set working folder > 07 Hospital name > klik icon tepi > Starting number > 1
Latihan_Penyediaan Lukisan > Ok. > ok > ok >ok.
3. Annotate tab > label & tables panel > Add 9. Set the target surface > 01EG_01_Tapak
label > feature > surface > label type >spot Sedia Ada > ok
elevation > spot elevation label style > 01 10. Set Grading layer > EW-SLP > ok
Platform level styles > marker style > < none 11. Klik create grading > klik garisan paling
> add >enter > 02EW_08_Rekabentuk atas > continue grading without feature line
Terperinci > ok > letakkan 3 point pada weeding > klik pada bahagian atas garis
surface > esc. yang diplih tadi > entire length > yes > cut
4. Toolspace > prospector > surface > tukar format > slope > cut slope > 1.5:1 > fill
semua surface style kepada 01 No Display format > slope > fill slope > 2:1.
5. Home tab > draw panel > polyline > buat Ulang langkah yang sama untuk kesemua
polyline pada garisan hijau > klik polyline > feature line > esc.
isolate selected object.
6. Home tab > create design panel > feature
line > create feature line from object > pilih

feature line > enter > site > klik icon

name > Site 2 > ok > name > 02EW_Site
2_Cerun Lukisan_ >tekan icon > Property
field > next counter > insert > number style >
01,02,03,.. > ok > layer > EW-SLP > check
erase existing entities and assign elevations
> ok.

61
[3]

[5]

62
[6] [7]

[8]

63
[11]

[12]

64
BAB 7B: PENYEDIAAN LUKISAN

Generate drawing
Fail latihan: C3D19_WIP_F1_02EW.dwg.

ARAHAN:

1. Buka fail > Folder latihan > 02 Coursework > 12. Layout tab > layout viewport panel
07 Hospital Latihan_Penyediaan Lukisan > >rectangular > klik pada viewport sebelah
02_WIP > C3D19_WIP_F1_02EW kanan bawah klik rectangular box > double
2. Klik kedua-dua kolam > layer > EW-SLP> klik pada tengah box > zoom sehingga
esc Nampak legend box > lock viewport.
3. Klik corridor > layer > EW-SLP > esc 13. Layout tools > rectangular viewport > buat
4. Feature line > layer > C-TOPO >esc kotak rectangular pada kotak nota
5. Taip LA > enter > turn off layer > C-ROAD , 14. Klik viewport dan zoom sehingga jumpa
C-ROAD-CORR, C-TOPO-GRAD, dan Mark. nota > lock viewport
6. Layer sates > new > new layer state name > 15. Application menu > drawing utilities >
Layer State Lukisan_Plan > ok > close. drawing properties > summary tab > tittle >
7. Xref > enter > detach lukisan 03 Projek Membina dan menyiapkan sebuah
ARCHITECT DRAWING hospital latihan > Subject > Lukisan Kerja
8. Buka fail 03 ARCHITECT DRAWING > klik Tanah > author > Ir.Sulaiman bin ahmad.
garisan paling atas > tukar warna objek 16. Custom tab > Disemak > Ir. Prem Kumar
tersebut kepada kod 251 > ok a/l Kaliappan > Dilukis > Siti Asmah Binti
9. Home tab > clipboard panel > Match Abdul Kahar > pengarah kanan > Ir.Hj.
properties > pilih semua properties yang lain Mohamad Zulkefly Bin Sulaiman >
> save as > 02 Coursework > 07 Hospital pengarah khidmat pakar dan pengurusan >
Latihan_Penyediaan Lukisan > 02_WIP > Ir. Mohd Azhari Bin Mohd Salleh >
C3D19_WIP_F1_02EW_Xref Arkitek > Tutup Jurutera awam penguasa kanan > Chow
lukisan. Wah > Jurutera awam penguasa > - >
10. Taip Xref > enter > attach > Jurutera awam kanan > Ir. Prem Kumar a/l
C3D19_WIP_F1_02EW_Xref Arkitek > Kaliappan > no fail projek >
Check locate using Georaphic Data > ok JKR.CKAS/05.500/020/JPM/012 > ok > re
11. Layout tab > click viewport > tukar saiz > > enter
1:1000 > adjust lukisan > klik icon lock.

65
[3] [4]

[6] [8]

66
[9] [10]

[11]

[12] [13]

67
 [14]

[15] [16]

68
BAB 7C: PENYEDIAAN LUKISAN

Plan production
Fail latihan: C3D19_WIP_F1_02EW.dwg.

ARAHAN:

1. Output tab > plan production panel > number > 04 > sheet tittle > Pelan Keratan
create section sheet > select alignment > Rentas Kerja Tanah 03 > ok
02EW_CL_01_Keratan > sample line group 5. Klik Lukisan Hospital Latihan > RC > Resave
name > Keratan melintang > select section all sheets > ok
view group > Section View Group – 1 > 6. Buka layout pelan kerja tanah > taip field >
layout name > section sheet – ( < [ next field category > sheetset > field names >
Counter(CP)]>) > Sheet Set > new sheet CurrentSheetTittle > Format > Uppercase >
set > LUKISAN HOSPITAL LATIHAN > ok > klik pada ruang tajuk lukisan >
Sheet set storage location > properties > text height > 3 > layer > EW-
>C:\Users\ubim040\Desktop\01_M.L.Kerja TX1 > color > 250
Tanah L2_23.05.2019\02 Coursework\07 7. Mtext > enter > klik pada ruangan no lukisan
Hospital Latihan_Penyediaan > JKR.CKAS/07.500/020/MOIS/J26/KT/
Lukisan\02_WIP > open > create sheets > (insert panel > field> field names >
ok CurrentSheetNumber > Current sheet
2. Sheet set manager > lukisan hospital number > 01> format > uppercase > ok) >
latihan > section view group – 1 > RC> (04)
import layout as sheet.. > browse for JKR.CKAS/07.500/020/MOIS/J26/KT/01(04)
drawings > C3D19_WIP_F1_02EW > open 8. Klik
> check pada layout sahaja > uncheck JKR.CKAS/07.500/020/MOIS/J26/KT/01(04)
prefix sheet titles with file name > import > properties > text height > 3 > layer > EW-
checked .(adjust layout letak pd atas) TX1 > color > 250.
3. Section view group-1 > RC > Rename 9. Klik tajuk lukisan dan no lukisan > RC >
subset > subset name > lukisan kerja clipboard > copy with base point > select
tanah > ok base point > buka layout kedua > paste
4. Layout . rc > rename an renumber > pada ruang berkaitan > regen. (Ulang
number > 01 > sheet tittle > Pelan Kerja langkah yang sama untuk layout 3 dan
Tanah > next > number > 02 > sheet tittle > layout 4)
Pelan Keratan Rentas Kerja Tanah 01 >
next> number > 03 > sheet tittle > Pelan
Keratan Rentas Kerja Tanah 02 > next >

69
10. Pelan kerja tanah layout > RC > page 11. Pelan keratan rentas kerja tanah 01 > RC >
setup manager > pelan kerja tanah > page setup manager > pelan kerja tanah >
modify > plot style table > modify > plot style table > Template Lukisan
monochrome.ctb > klik button edit > BKA > ok close. (ulang langkah yang sama
plih color 251 > screening > 50 > save untuk pelan keratan rentas kerja tanah 02 dan
as > Template Lukisan BKA > save > pelan keratan rentas kerja tanah 03)
save & close > ok >plot style table > Lukisan kerja tanah > RC > publish > publish to
Template Lukisan BKA > ok DWFx > name >
jkrCv19_1_(BMhpB1_19_001)F1_EW_190101a
> C:\Users\ubim040\Desktop\01_M.L.Kerja
Tanah L2\02 Coursework\07 Hospital
Latihan_Penyediaan Lukisan\04_PUBLISH.

[1]

70
71
[4]

[6]

[9]

72
73
[10]

[11]

74