Optical smoke/heat detector

Salwico NS-A OHS

Part no. N11242

System: Salwico CS4000, NSAC-1 fire alarm system

Item 220
Description Data
The NS-AOHS is an analogue addressable multi sensor fire Smoke sensing method Light scattering type Infra-red
detector for Salwico addressable fire alarm systems NSAC-1 Alarm temperature 84ºC
and CS4000 together with SPK-2 rev.3. System voltage 24 VDC
It has two separate analogue sensor elements. One optical for Workingvoltage 15 - 35 VDC
smoke detection and one heat sensing element for heat Working current
detection. - supervising 0.2 mA
The alarm temperature is 84ºC. - alarm 2.5 mA
The address is set with a DIP-switch mounted in the back of Remote output 2 mA (for remote indication)
the detector. Operating temperature -25ºC to +70ºC
When the detector is in alarm condition, a red LED on the Ambient humidity 0 - 95% RH
detector is lit. The LED is lit until the alarm has been reset at Colour White
the control panel. Weight ~120 g
The detector is polarity independent.
An external LED indicator, buzzer etc. can be connected to
the remote output. Base plates
The polarity of the loop has to be connected according to the
For information about suitable base plates, see separate
drawing below, if the remote output is used.
document ”Base matrix Salwico units”.

Dimensions (mm) Connection

Loop in P/1(+) Loop out

C/6(-)
L/3(-)

2 mA remote
output

Specifications may be subject to change for improvement without prior notice Data sheet no: N11242.03.2.E

Consilium Marine AB
ÇConsilium P.O. Box 8763, SE-402 76 Göteborg, Sweden
Phone +46 31 710 77 00 Fax +46 31 710 78 00
www.consilium.se
 IP55 base plate adapter
Salwico SPB-1
Part no. 46915

System: All Salwico fire alarm systems

Item 221
Description Data
The SPB-1 is a connection adapter for the NS-2IP55 base Cable terminals 2.5 mm2
(part no. 46900 or 46950). Ingress protection IP55 (mounted on the base
Smoke, heat and flame detectors can be connected to this NS-2IP55)
adapter. Colour White
The adapter can be used for all Salwico fire alarm systems. Weight ~105 g
The remote output can not be used if an addressable non
NS-type detector or a conventional NS-type detector is
connected to the SPB-1.

Dimensions (mm) Connection

M6 Addressable NS-type detectors

29

Loop in P(+) Loop out

15

C(-)
L(-)
Ø104
2 mA remote
output

Addressable detectors (not NS-type)

Loop in L(+) Loop out
C(-)

Conventional NS-type detectors

SPB-1

P L CL CR

Last detector
Section L(+) L(+)
End of line
C(-) C(-)
P(-) P(-) resistor

Conventional detectors (not NS-type)

Last detector
Section L(+) L(+)
End of line
C(-) C(-)
resistor
P(-) P(-)
116 R(-) R(-)

2 mA remote 2 mA remote
output output

Detector RDJ-2T with SUM-2

Loop in L(+) Loop out
C(-)
P(+)
SUM-2
R(-)

Specifications may be subject to change for improvement without prior notice Data sheet no: 46915.03.1.E

Consilium Marine AB
ÇConsilium P.O. Box 8763, SE-402 76 Göteborg, Sweden
Phone +46 31 710 77 00 Fax +46 31 710 78 00
www.consilium.se
 IP55 base
Salwico 2IP55
Part no. 46950

System: All Salwico fire alarm systems

Item 222
Description Data
The 2IP55 is a base for all Salwico IP55 detector adapters. Cable diameter Ø6-14 mm
Together with the adapters it is possible to install smoke, Ingress protection IP55
heat and flame detectors in harsh environment with an Fire class V1
ingress protection up to IP55. Temperature range -30ºC to +100ºC
It can be used for both addressable and conventional fire Material Polyamide/glass (PA666, 15% GW)
alarm systems. Colour White
Weight ~100 g

Dimensions (mm)

Specifications may be subject to change for improvement without prior notice Data sheet no: 46950.03.1.E

Consilium Marine AB
ÇConsilium P.O. Box 8763, SE-402 76 Göteborg, Sweden
Phone +46 31 710 77 00 Fax +46 31 710 78 00
www.consilium.se