Scribd
Upload
76 views

Auto Steer Schematic

The document describes a BAT circuit with the following key components: - An isolation circuit that includes a 12S1 and 12S2 relay and 1000uF capacitor to provide power isolation. - A 7805 voltage regulator IC2 that steps down the input voltage to +5V for other components. - Additional circuitry including diodes, resistors, and relays to control power flow and signaling between different parts of the circuit. - The overall circuit provides isolated and regulated power to downstream components from a +15V input source.

Uploaded by

Mario Alfaro Cano
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
76 views

Auto Steer Schematic

The document describes a BAT circuit with the following key components: - An isolation circuit that includes a 12S1 and 12S2 relay and 1000uF capacitor to provide power isolation. - A 7805 voltage regulator IC2 that steps down the input voltage to +5V for other components. - Additional circuitry including diodes, resistors, and relays to control power flow and signaling between different parts of the circuit. - The overall circuit provides isolated and regulated power to downstream components from a +15V input source.

Uploaded by

Mario Alfaro Cano
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

BAT

BAT1

Isolation

+15V

GN5
GN2

GN3
GN1
GN4
GND
12S1

12S2

+5V
Relays
1000uF
12S

C21
87 87A

K4 GND

1N4004

1N4004
D2 C22

30
4N33
SpiceOrder 1 SpiceOrder 2

K4 3A diode GND 1
1000uF
D3

D1
CB1-P-12V
86

2 4 2
SpiceOrder 2

SpiceOrder 2
C20 3
1 5
SpiceOrder 1

SpiceOrder 1
1000uF 2 6 1
R3 1k
85

2 GND GND OK3 R8 0


2 1
1

PWM1
PWM2
IN OUT

Dir1

Gnd
GND
IC3 1 Gnd
7805 7805 2 Auto
GND IC2
GND 3
+15v

1
2
3
4
GND
OUT IN

GND GND
1 Gnd
2 2 Imp

R10 330
1 3
+15v

330
R14
GND 1 Gnd

330
2 GND 2 Steer
1 3
USB 4N33 +15v

R11
R19

4 2
1k

J2.15 J1.15
D13/SCK D12/MISO
J2.14 J1.14 5
1 J2.13
3V3 D11/MOSI
J1.13 6 1
R13 1k
3.3V 330 R2 AREF D10
LED1
3mm

+15V
2 3 J2.12 J1.12
SDA A0 D9 R5 330
SCL
3 2 J2.11
A1 D8
J1.11 OK1
C23 330 R1 4N33
IC1 I2
4 1 J2.10
A2 D7
J1.10
GND 5 J2.9 J1.9 4 2
1000uF I1 A3 D6 R4 330
6 J2.8 J1.8
GND
J2.7
A4 D5
J1.7
R18 330 5
J2.6
A5 D4
J1.6 6 1
R12 1k
+5V

A6 D3
GND GND J2.5 J1.5
A7 D2
J2.4
5V GND.1
J1.4 OK2
J2.3 J1.3
RST.2 RST.1

2
1
C1 J2.2 J1.2
GND.2 D0/RX
10 J2.1 J1.1
A3 0.1 VIN D1/TX
9
A2
ADC-4CH-ADS1115

8
A1 ARDUINO-NANO-3.0
7 GND
1k R6 A0 M1
GND
+5V 4
ALRT
6
Sense High 3 5
1k R7 ADDR
2 4
Sense Low 1
SDA
3 C2
+5V

Gnd SCL
2
GND 0.1
C3 C4 1
VDD
330 R9

0.1 0.1 C6 TITLE: diyAutoSteer


1k R16

1k R17

C5
U2 0.1 1
0.1 2 Document Number: REV:
GND
3
GND
Date: 2019-05-30 8:30 AM Sheet: 1/1

2019-08-25 10:36 PM C:\Users\Grizs\Documents\eagle7\diyAutoSteer\diyAutoSteer.sch (Sheet: 1/1)

You might also like