Scribd
Upload
168 views

OBD Tracking Device Immobilizer Installation User Guide

This document provides instructions for installing an immobilizer device using an OBDII port. It outlines the pinouts for the OBDII interface and device, and describes two methods for connecting an immobilizer relay to either cut the engine start line or oil pump to disable the vehicle. The first method uses a pin wire connected to pin 12 of the OBDII port, while the second method uses a T-wire connected to the relay without modifying the OBDII port. Diagrams illustrate the wiring connections for each immobilizer control configuration.

Uploaded by

Htun NayWin
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
168 views

OBD Tracking Device Immobilizer Installation User Guide

This document provides instructions for installing an immobilizer device using an OBDII port. It outlines the pinouts for the OBDII interface and device, and describes two methods for connecting an immobilizer relay to either cut the engine start line or oil pump to disable the vehicle. The first method uses a pin wire connected to pin 12 of the OBDII port, while the second method uses a T-wire connected to the relay without modifying the OBDII port. Diagrams illustrate the wiring connections for each immobilizer control configuration.

Uploaded by

Htun NayWin
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 7

Ulbotech

OBD Tracking Device


Immobilizer Installation
User Guide

www.ulbotech.com | Page 1
1. J1962 OBDII interface Pinout:

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16

PIN DESCRIPTION PIN DESCRIPTION


1 Vender option 9 Vender option
2 J1850 Bus + 10 J1850 Bus -
3 Vender option 11 Vender option
4 Chassis Ground 12 Vender option
5 Signal Ground 13 Vender option
6 CAN High 14 CAN Low
7 K Line 15 L Line
8 Vender option 16 Battery Power

2. Device OBDII interface Pinout:

8 7 6 5 4 3 2 1

16 15 14 13 12 11 10 9

PIN DESCRIPTION PIN DESCRIPTION


1 NC 9 NC
2 J1850 Bus + 10 J1850 Bus -
3 NC 11 NC
4 Ground 12 Immobilizer Out
5 Ground 13 NC
6 CAN High 14 CAN Low
7 K Line 15 L Line
8 NC 16 Battery Power

www.ulbotech.com | Page 2
3. Use PIN wire connection immobilizer:
If the No of Pin12 of OBDII interface on your car is available, you can install a Pin
with the immobilizer output wire on the Pin12 location of the OBDII port. But firstly
you need to remove the OBDII port from your car , after insert the PIN wire which
we provided as below picture showed.

When you done the pin wire installation, you can start connecting immobilizer as
below two solutions:

3.1 Immobilizer control engine start：

PIN12
OFF O
N

S
TA
RT
Engine
Start Line

Relay Cut
OBDII Tracking Device

Connect to
Battery

www.ulbotech.com | Page 3
3.2 Immobilizer control oil pump：

PIN12
To Oil
Pump

Relay Cut

Connect to
Battery Oil
OBDII Tracking Device Pump

GND

www.ulbotech.com | Page 4
4. Use T wire connection immobilizer:
If the No of Pin 12 of OBDII interface on your car is unavailable or you do not
want to install a Pin wire. You can use the T wire which we provided to connect
the immobilizer relay. Then you just need to connect the T wire as below
indication, after insert OBDII port, the immobilizer will be worked .T wire as below
picture showed:

1000mm
AWG18 Black
AWG18 Red

Here’re two installation solutions:

www.ulbotech.com | Page 5
4.1 Immobilizer control engine start：

OFF O
N

ST
AR
T
Engine
Start Line

Cut

Relay

OBDII Tracking Device

Relay

www.ulbotech.com | Page 6
4.2 Immobilizer control oil pump：

To Oil
Pump

Cut

Relay
Oil
Pump

OBDII Tracking Device

GND
Relay

www.ulbotech.com | Page 7

You might also like