GROUP 2 SPECIFICATION

1. MAJOR COMPONENT(HL730-7)

Bucket Tire Hydraulic tank Radiator

Boom Main control valve Cab Air cleaner Counterweight

Bucket link Bell crank Bucket cylinder Main pump Engine Muffler

Boom cylinder Front axle Steering cylinder Transmission Rear axle Fuel tank

73072SP01

1-10
MAJOR COMPONENT(HL730TM-7)

Bucket Tire Hydraulic tank Radiator

Boom Main control valve Cab Air cleaner Counterweight

Quick coupler Link Bucket cylinder Main pump Engine Muffler

Boom Front axle Steering cylinder Transmission Rear axle Fuel tank

730TM72SP01

1-11
2. SPECIFICATIONS
1) WITHOUT TOOTH AND CUTTING EDGE TYPE BUCKET(HL730-7)

F
J
B

4790
H

3640

2830
K

C
G
40

47
0
5570 0

D
E 1800
A
73072SP02

Description Unit Specification

Operating weight kg(lb) 9700(21380)
Struck 1.4(1.9)
Bucket capacity m3(yd3)
Heaped 1.7(2.2)
Overall length A 6770(22' 3")
Overall width B 2450( 8' 0")
Overall height C 3120(10' 3")
Ground clearance D 370( 1' 3")
Wheelbase E mm(ft-in) 2750( 9' 0")
Tread F 1850( 6' 0")
Dump clearance at 45° G 2780( 9' 1")
Dump reach(Full lift) H 970( 3' 2")
Width over tires I 2295( 7' 6")
Dump angle J 48
Degree (°)
Roll back angle(Carry position) K 48
Lift(With load) 5.2
Cycle time Dump(With load) sec 1.0
Lower(Empty) 2.3
Maximum travel speed km/hr(mph) 37.0(23.1)
Braking distance 12(39' 4")
m(ft-in)
Minimum turning radius(Center of outside tire) 4.70(15' 5")
Gradability Degree (°) 30
First gear 6.9(4.3)
Second gear 12.1(7.5)
Forward
Third gear 22.1(13.8)
Travel speed Fourth gear km/hr(mph) 37.0(23.1)
First gear 7.3(4.5)
Reverse Second gear 12.8(8.0)
Third gear 23.3(14.5)

1-12
 WITHOUT TOOTH AND CUTTING EDGE TYPE BUCKET(HL730TM-7)

F
B

I
4870
H

3780

2830
K

C
G
40

47
5409 00

D
E 1800
A
730TM72SP02

Description Unit Specification

Operating weight kg(lb) 10000(22050)
Struck 1.4(1.9)
Bucket capacity m3(yd3)
Heaped 1.6(2.1)
Overall length A 6920(22' 8")
Overall width B 2400( 7' 10")
Overall height C 3120(10' 3")
Ground clearance D 370( 1' 3")
Wheelbase E mm(ft-in) 2750( 9' 0")
Tread F 1850( 6' 0")
Dump clearance at 45° G 2845( 9' 4")
Dump reach(Full lift) H 1115( 3' 8")
Width over tires I 2295( 7' 6")
Dump angle J 50
Degree (°)
Roll back angle(Carry position) K 54
Lift(With load) 5.4
Cycle time Dump(With load) sec 1.4
Lower(Empty) 2.4
Maximum travel speed km/hr(mph) 37.0(23.1)
Braking distance 12(39' 4")
m(ft-in)
Minimum turning radius(Center of outside tire) 4.7(15' 5")
Gradability Degree (°) 30
First gear 6.9(4.3)
Second gear 12.1(7.5)
Forward
Third gear 22.1(13.8)
Travel speed Fourth gear km/hr(mph) 37.0(23.1)
First gear 7.3(4.5)
Reverse Second gear 12.8(8.0)
Third gear 23.3(14.5)

1-13
 2) WITH BOLT-ON CUTTING EDGE TYPE BUCKET(HL730-7)

F
B

4790
H

3640

2830
K

C
G
40

47
0
5595 0

D
E 1800
A
73072SP03

Description Unit Specification

Operating weight kg(lb) 9700(21380)
Struck 1.5(2.0)
Bucket capacity m3(yd3)
Heaped 1.8(2.4)
Overall length A 6850(22' 6")
Overall width B 2450( 8' 0")
Overall height C 3120(10' 3")
Ground clearance D 370( 1' 3")
Wheelbase E mm(ft-in) 2750( 9' 0")
Tread F 1850( 6' 0")
Dump clearance at 45° G 2730( 8' 11")
Dump reach(Full lift) H 1005( 3' 4")
Width over tires I 2295( 7' 6")
Dump angle J 48
Degree (°)
Roll back angle(Carry position) K 48
Lift(With load) 5.2
Cycle time Dump(With load) sec 1.0
Lower(Empty) 2.3
Maximum travel speed km/hr(mph) 37.0(23.1)
Braking distance 12(39' 4")
m(ft-in)
Minimum turning radius(Center of outside tire) 4.70(15' 5")
Gradability Degree (°) 30
First gear 6.9(4.3)
Second gear 12.1(7.5)
Forward
Third gear 22.1(13.8)
Travel speed Fourth gear km/hr(mph) 37.0(23.1)
First gear 7.3(4.5)
Reverse Second gear 12.8(8.0)
Third gear 23.3(14.5)

1-14
 WITH BOLT-ON CUTTING EDGE TYPE BUCKET(HL730TM-7)

F
J
B

I
4870
H

3780

2830
K

C
G
40

47
5444 00

D
E 1800
A
730TM72SP03

Description Unit Specification

Operating weight kg(lb) 10000(22050)
Struck 1.5(2.0)
Bucket capacity m3(yd3)
Heaped 1.7(2.2)
Overall length A 7000(24' 9")
Overall width B 2400( 8' 4")
Overall height C 3120(10' 3")
Ground clearance D 370( 1' 3")
Wheelbase E mm(ft-in) 2750( 9' 0")
Tread F 1850( 6' 0")
Dump clearance at 45° G 2785( 9' 2")
Dump reach(Full lift) H 1140( 3' 9")
Width over tires I 2295( 7' 6")
Dump angle J 50
Degree (°)
Roll back angle(Carry position) K 54
Lift(With load) 5.4
Cycle time Dump(With load) sec 1.4
Lower(Empty) 2.4
Maximum travel speed km/hr(mph) 37.0(23.1)
Braking distance 12(39' 4")
m(ft-in)
Minimum turning radius(Center of outside tire) 4.7(15' 5")
Gradability Degree (°) 30
First gear 6.9(4.3)
Second gear 12.1(7.5)
Forward
Third gear 22.1(13.8)
Travel speed Fourth gear km/hr(mph) 37.0(23.1)
First gear 7.3(4.5)
Reverse Second gear 12.8(8.0)
Third gear 23.3(14.5)

1-15
 3) WITH TOOTH TYPE BUCKET(HL730-7 ONLY)

F
B

4790
H

3640

2830
K

C
G
40

47
0
5640 0

D
E 1800
A
73072SP04

Description Unit Specification

Operating weight kg(lb) 9700(21380)
Struck 1.4(1.9)
Bucket capacity m3(yd3)
Heaped 1.7(2.2)
Overall length A 6950(22' 10")
Overall width B 2480( 8' 2")
Overall height C 3120(10' 3")
Ground clearance D 370( 1' 3")
Wheelbase E mm(ft-in) 2750( 9' 0")
Tread F 1850( 6' 0")
Dump clearance at 45° G 2650( 8' 8")
Dump reach(Full lift) H 1075( 3' 6")
Width over tires I 2295( 7' 6")
Dump angle J 48
Degree (°)
Roll back angle(Carry position) K 48
Lift(With load) 5.2
Cycle time Dump(With load) sec 1.0
Lower(Empty) 2.3
Maximum travel speed km/hr(mph) 37.0(23.1)
Braking distance 12(39' 4")
m(ft-in)
Minimum turning radius(Center of outside tire) 4.70(15' 5")
Gradability Degree (°) 30
First gear 6.9(4.3)
Second gear 12.1(7.5)
Forward
Third gear 22.1(13.8)
Fourth gear km/hr(mph) 37.0(23.1)
Travel speed
First gear 7.3(4.5)
Reverse Second gear 12.8(8.0)
Third gear 23.3(14.5)

1-16
3. WEIGHT
HL730-7 HL730TM-7 HL730-7 HL730TM-7
Item
kg lb
Front frame assembly 750 760 1650 1680
Rear frame assembly 1000 2200
Front fender(LH & RH) 20 44
Rear fender(LH & RH) 33 73
Counterweight 300 410 660 900
Cab assembly 820 1810
Engine assembly 340 750
Transmission assembly 380 840
Drive shaft(Upper, engine to transmission) 7 15
Drive shaft(Front) 17 37
Drive shaft(Center) 17 37
Drive shaft(Rear) 9 20
Front axle(Include differential) 490 1080
Rear axle(Include differential) 480 1060
Tire(4EA) 330 730
Hydraulic tank 170 380
Fuel tank 240 530
Main pump assembly 26 57
Main control valve 22 49
Boom assembly 540 510 1190 1120
Bell crank assembly 140 - 310 -
Bucket link 27 41 60 90
Quick coupler - 210 - 460
Bucket, with bolt on cutting edge 710 610 1570 1340
Bucket, with tooth 780 - 1720 -
Without tooth and cutting edge 640 600 1410 1320
Boom cylinder assembly(2EA) 70 150
Bucket cylinder assembly 78 62 170 140
Steering cylinder assembly(2EA) 15 30
Quick coupler cylinder assembly - 5.5 - 12
Seat 40 88
Battery 28 62

1-17
4. SPECIFICATION FOR MAJOR COMPONENTS
1) ENGINE
Item Specification

Model Cummins B3.9-C

Type 4-cycle turbocharged and after cooled diesel engine
Cooling method Water cooling
Number of cylinders and arrangement 4 cylinders, in-line
Firing order 1-3-2-4
Combustion chamber type Direct injection type
Cylinder bore × stroke 102×120mm(4.02"×4.72")
Piston displacement 3920cc(239cu in)
Compression ratio 18.0 : 1
Rated gross horse power 125hp at 2200rpm
Maximum gross torque at 1300rpm 52kgf・m(376lbf・ft)
Engine oil quantity 11ℓ (2.9 U.S. gal)
Dry weight 338kg(745lb)
High idling speed 2420 ± 50rpm
Low idling speed 1000 ± 50rpm
Rated fuel consumption 231g/kw・hr
Starting motor Nippondenso 228000-7902 (24V-3.7kw)
Alternator Delco Remy 22SI(24V-70Amp)
Battery 2×12V×100Ah

1-18
 2) MAIN PUMP
Item Specification
Type Fixed displacement tandem helical gear pump
Capacity 36+28.5cc/rev
Maximum operating pressure 210kgf/cm2(2990psi)
Rated operating speed 2200rpm
Rated output flow 140ℓ/min(40U.S.gpm)

3) FAN AND BRAKE PUMP

Specification
Item
Fan Brake
Type Fixed displacement tandem helical gear pump
Capacity 16.8cc/rev 8.2cc/rev
Maximum operating pressure 85kgf/cm2(1210psi) 150kgf/cm2(2130psi)
Rated operating speed 2200rpm
Rated output flow 35ℓ/min(9.2U.S.gpm) 17ℓ/min(4.5U.S.gpm)

4) MAIN CONTROL VALVE

Item Specification

Type 2 spool(sectional block)

Operating method Hydraulic pilot assist
Main relief valve set pressure 210kgf/cm2(2990psi)
Overload relief valve set pressure 240kgf/cm2(3414psi)

5) REMOTE CONTROL VALVE

Item Specification

Type Joystick(or with aux lever)

Minimum 3.7kgf/cm2(52.6psi)
Control pressure
Maximum 30kgf/cm2(427psi)

6) CYLINDER

Item Specification

Boom cylinder Bore dia×Rod dia×Stroke Ø105×Ø65×772mm

Bucket cylinder Bore dia×Rod dia×Stroke Ø120×Ø70×510mm
Steering cylinder Bore dia×Rod dia×Stroke Ø 60×Ø35×412mm
Quick coupler cylinder Bore dia×Rod dia×Stroke Ø 50×Ø25×79mm

1-19
 7) DYNAMIC POWER TRANSMISSION DEVICES

Item Specification

Model ZF 4WG130
Torque converter
Type Single-stage, single-phase
Type Full-automatic power shift
Transmission Gear shift Forward fourth gear, reverse third gear
Adjustment Electrical single lever type, kick-down system
Drive devices 4-wheel drive
Axle Front Front fixed location
Rear Oscillation ±12。of center pin-loaded
Wheels Tires 17.5-25, 12PR(L3)
Travel Four-wheel, wet-disc type, full hydraulic
Brakes Spring applied, hydraulic released brake in front
Parking axle
Type Full hydraulic, articulated
Steering
Steering angle 40。to both right and left angle, respectively

1-20
5. TIGHTENING TORQUE OF MAJOR COMPONENT
No Items Size kgf・m lbf・ft

1 Engine mounting bolt, nut(4EA) M16×2.0 29.7±4.5 215±32.5

2 Engine mounting bolt(Bracket) M12×1.75 10.7±1.6 77.4±11.6
3 Engine Radiator mounting bolt M16×2.0 29.7±4.5 215±32.5
4 Fuel tank mounting bolt M16×2.0 29.7±4.5 215±32.5
5 Air cleaner mounting bolt(4EA) M 8×1.25 2.5±0.5 18.1±3.6
6 Main pump housing mounting bolt M14×2.0 19.6±2.9 142±20.9
7 Main control valve mounting bolt M12×1.75 12.8±3.0 92.6±21.7
8 Steering unit mounting bolt M10×1.5 6.9±1.4 49.9±10.1
9 Priority valve M 8×1.25 2.5±0.5 18.1±3.6
10 Brake valve mounting bolt M 8×1.25 2.5±0.5 18.1±3.6
Hydraulic
11 Fan and brake pump mounting bolt M10×1.5 6.9±1.4 49.9±10.1
system
12 Cut-off valve mounting bolt M12×1.75 12.8±3.0 92.6±21.7
13 Remote control lever mounting bolt M 6×1.0 1.1±0.2 8.0±1.4
14 Pilot supply unit mounting bolt M 8×1.25 2.5±0.5 18.1±3.6
15 Safety valve M 8×1.25 2.5±0.5 18.1±3.6
16 Hydraulic oil tank mounting bolt M16×2.0 29.7±4.5 215±32.5
17 Transmission mounting bolt(Bracket, front) M20×2.5 57.9±8.7 419±62.9
18 Transmission mounting bolt(Bracket, rear) M16×2.0 18.4±2.0 133±14.5
19 Power train Front axle mounting bolt, nut M24×2.5 100±15 723±109
20 system Rear axle support mounting bolt, nut M24×2.0 100±15 723±109
21 Tire mounting nut(17.5-25, 12PR, L3) M22×1.5 70±2.0 506±15
22 Drive shaft joint mounting bolt 3/8-24UNF 6.0±0.8 43.4±5.8
23 Counterweight mounting bolt, nut M24×2.0 107±16 773±116
24 Others Operator’s seat mounting bolt M 8×1.25 3.4±0.8 24.6±5
25 ROPS Cab mounting bolt(4EA) M24×3.0 27.5±2.5 199±18.1

1-21
6. TORQUE CHART
Use following table for unspecified torque.
1) BOLT AND NUT
(1) Coarse thread
8T 10T
Bolt size
kgf・m lbf・ft kgf・m lbf・ft
M 6 × 1.0 0.85 ~ 1.25 6.15 ~ 9.04 1.14 ~ 1.74 8.2 ~ 12.6
M 8 × 1.25 2.0 ~ 3.0 14.5 ~ 21.7 2.73 ~ 4.12 19.7 ~ 29.8
M10 × 1.5 4.0 ~ 6.0 28.9 ~ 43.4 5.5 ~ 8.3 39.8 ~ 60
M12 × 1.75 7.4 ~ 11.2 53.5 ~ 79.5 9.8 ~ 15.8 71 ~ 114
M14 × 2.0 12.2 ~ 16.6 88.2 ~ 120 16.7 ~ 22.5 121 ~ 167
M16 × 2.0 18.6 ~ 25.2 135 ~ 182 25.2 ~ 34.2 182 ~ 247
M18 × 2.5 25.8 ~ 35.0 187 ~ 253 35.1 ~ 47.5 254 ~ 343
M20 × 2.5 36.2 ~ 49.0 262 ~ 354 49.2 ~ 66.6 356 ~ 482
M22 × 2.5 48.3 ~ 63.3 350 ~ 457 65.8 ~ 98.0 476 ~ 709
M24 × 3.0 62.5 ~ 84.5 452 ~ 611 85.0 ~ 115 615 ~ 832
M30 × 3.5 124 ~ 168 898 ~ 1214 169 ~ 229 1223 ~ 1655
M36 × 4.0 174 ~ 236 1261 ~ 1703 250 ~ 310 1808 ~ 2242

(2) Fine thread

8T 10T
Bolt size
kgf・m lbf・ft kgf・m lbf・ft
M 8 × 1.0 2.17 ~ 3.37 15.7 ~ 24.3 3.04 ~ 4.44 22.0 ~ 32.0
M10 × 1.25 4.46 ~ 6.66 32.3 ~ 48.2 5.93 ~ 8.93 42.9 ~ 64.6
M12 × 1.25 7.78 ~ 11.6 76.3 ~ 83.7 10.6 ~ 16.0 76.6 ~ 115
M14 × 1.5 13.3 ~ 18.1 96.2 ~ 130 17.9 ~ 24.1 130 ~ 174
M16 × 1.5 19.9 ~ 26.9 144 ~ 194 26.6 ~ 36.0 193 ~ 260
M18 × 1.5 28.6 ~ 43.6 207 ~ 315 38.4 ~ 52.0 278 ~ 376
M20 × 1.5 40.0 ~ 54.0 289 ~ 390 53.4 ~ 72.2 386 ~ 522
M22 × 1.5 52.7 ~ 71.3 381 ~ 515 70.7 ~ 95.7 512 ~ 692
M24 × 2.0 67.9 ~ 91.9 491 ~ 664 90.9 ~ 123 658 ~ 890
M30 × 2.0 137 ~ 185 990 ~ 1338 182 ~ 248 1314 ~ 1795
M36 × 3.0 192 ~ 260 1389 ~ 1879 262 ~ 354 1893 ~ 2561

1-22
2) PIPE AND HOSE(FLARE TYPE)

Thread size(PF) Width across flat(mm) kgf・m lbf・ft

1/4" 19 4 28.9
3/8" 22 5 36.2
1/2" 27 6 43.4
3/4" 36 12 86.8
1" 41 14 101

3) PIPE AND HOSE(ORFS TYPE)

Thread size(UNF) Width across flat(mm) kgf・m lbf・ft

13/16-16" 24 4.4 32.5

1-3/16-12" 36 9.3 67.3
1-7/16-12" 41 13.2 95.5
1-11/16-12" 50 18.3 132.4
2-12" 55 22.6 163.5

4) FITTING

Thread size(PF) Width across flat(mm) kgf・m lbf・ft

1/4" 19 4 28.9
3/8" 22 5 36.2
1/2" 27 6 43.4
3/4" 36 13 94.0
1" 41 15 109

1-23
7. RECOMMENDED LUBRICANTS
Use only oils listed below or equivalent.
Do not mix different brand oil.
Ambient temperature °
C( °
F)
Capacity
Service point Kind of fluid -20 -10 0 10 20 30 40
ℓ(U.S. gal)
(-4) (14) (32) (50) (68) (86) (104)

SAE 30

SAE 10W
Engine oil pan Engine oil 11(2.9)
SAE 10W-30

SAE 15W-40

Torque converter SAE 10W-30

Transmission Oil 20(5.3)
SAE 15W-40

Front : 18.4(4.9)
Axle Gear oil SAE 80W-90LSD/API GL-5
Rear : 18.4(4.9)

Tank: ISO VG 32
90(24)
Hydraulic tank Hydraulic oil ISO VG 46
System:
125(33) ISO VG 68

ASTM D975 NO. 1

Fuel tank Diesel fuel 202(53)
ASTM D975 NO. 2

NLGI NO. 1
Fitting
Grease As required
(Grease nipple)
NLGI NO. 2

Mixture of
antifreeze Ethylene glycol base permanent type
Radiator and water 30(7.9)
50 : 50

1-24