100% found this document useful (3 votes)

2K views

Ak95S Error Code List

This document contains error codes and explanations for various components of the AK 95 S blood treatment machine. It includes error codes for issues with the venous pressure sensor, blood pump control, arterial and venous clamps, blood volume measurement, and blood flow measurement. The errors relate to issues with software, timers, registers, and sensor readings being out of expected limits. Providing specific error codes helps with troubleshooting and determining the root cause of any issues.

Uploaded by

Enderson Ramos

We take content rights seriously. If you suspect this is your content, claim it here.

Available Formats

Download as PDF, TXT or read online on Scribd

100% found this document useful (3 votes)

2K views

Ak95S Error Code List

Uploaded by

Enderson Ramos

We take content rights seriously. If you suspect this is your content, claim it here.

Available Formats

Download as PDF, TXT or read online on Scribd

You are on page 1/ 118

Table of content

C CB......................................................................................................................................................... 1
C CC......................................................................................................................................................... 6
C CF ....................................................................................................................................................... 13
C CO....................................................................................................................................................... 36
C FRFF.................................................................................................................................................. 81
P PTRA .................................................................................................................................................. 83
C Cx 000................................................................................................................................................. 85
C CSYS .................................................................................................................................................. 86
C EBUF .................................................................................................................................................. 91
C SYS and P SYS................................................................................................................................... 92
P ENV .................................................................................................................................................... 95
P POW.................................................................................................................................................... 96
P PPR...................................................................................................................................................... 97
P PSYS ................................................................................................................................................... 98
P PREC................................................................................................................................................... 99
P SDT ................................................................................................................................................... 100
W WAD ............................................................................................................................................... 102
W WPR ................................................................................................................................................ 103
W WSYS .............................................................................................................................................. 104
? UDEF................................................................................................................................................. 105
Computer start-up sequence ………………………………………………………………………..…106

This error code list is intended for use together with AK 95 / AK 95 S, program version 12.20
Please report to Gambro ITS the occurrence of all “Internal Software Error”, use fax number below.

Important!
This error code list is valid for all versions of electronics. Whenever a component reference have
changed a note to N.E. (new electronics) is supplied.

Gambro Customer Support

Fax no. +46 46 16 96 86
About...Arrays
An array is a defined block of computer memory. It consists of elements, and the
number of elements determine the array size. The elements are accessed by their
index numbers. The index number is placed in parenthesis after the array name,
e.g. ArrayName(99). This array consists of 100 elements (0-99):

Array element (2)

0 1 2 3 4 98 99

Array index

- Internal software error.
- The timer IC 34 on the control driver board is broken.

C CB 009 003 NUMBER OF TACHO PULSES ERROR

Unconditional error, blood pump not available

General description of conditions for occurring:

The number of counted blood pump tacho pulses is incorrect.

Technical description of conditions for occurring:

Either 0 or more than 10000 tacho pulses have been counted since the last
time the blood flow was measured

Some possible explanations why the error has occurred:

HCEN 9091 Page 2 of 106

- No connection between tacho and BM I/O board
- Blood pump error (blood pump stopped)
- The timer IC 34 on the control driver board is broken.

C CB 009 004 MEASURED BLOOD FLOW OUT OF LIMITS

Unconditional error, blood pump not available

General description of conditions for occurring:

- The measured blood flow has differed too much from the blood flow set
value.

Technical description of conditions for occurring:

- BRI(BI_BloodFlActSet) - BRI(BI_BloodFl) < -600
or
BRI(BI_BloodFlActSet) - BRI(BI_BloodFl) > 600

Some possible explanations why the error has occurred:

- The blood pump unit is broken
- The BM I/O board is broken (Q1-Q4 and components)
- The timer IC 34 on the control driver board is broken.

C CB 010, Heparin Pump

C CB 010 000 CASE ERROR
Transient error

General description of conditions for occurring:

- Internal software error

C CB 010 001 ERROR DURING REGISTER LOAD/READ

Conditional error, confirm by zero-set heparin flow

General description of conditions for occurring:

- The heparin pump timer is not working properly

Technical description of conditions for occurring:

- The timer 9513 has returned error message(s).

Some possible explanations why the error has occurred:

C CB 015, Auto Rinse Back

C CB 015 000 CASE ERROR
Transient error

General description of conditions for occurring:

- An error occurred while reading transducer parameters during init (start-up).

Some possible explanations why the error has occurred:

HCEN 9091 Page 8 of 106

- No connection between transducer board and FM I/O board
- No connection between FM I/O board and control driver board
- Transducer board mounted in incorrect position on FM I/O board
- Incorrect transducer ID. Update transducer ID (I2C scan).
- EEPROM on transducer board is broken
- Serial bus error on control CPU board, or I/O SIMM problem (P310)
- Uncalibrated transducer. Calibrate transducer
- Broken FM I/O board

C CC 008 101 ERROR READING PARAMETERS FROM REG. TEMP. (HEAT)

Unconditional error, blood pump not available

General description of conditions for occurring:

- An error occurred while reading transducer parameters during init (start-up).

Some possible explanations why the error has occurred:

- Refer to error description for C CC 008 100

C CC 008 102 ERROR READING PARAMETERS FROM DEGASS PRESSURE

Unconditional error, blood pump not available

General description of conditions for occurring:

- An error occurred while reading transducer parameters during init (start-up).

Some possible explanations why the error has occurred:

- Refer to error description for C CC 008 100

C CC 008 103 ERROR READING PARAMETERS FOR HIGH PRESSURE GUARD

Unconditional error, blood pump not available

General description of conditions for occurring:

- An error occurred while reading transducer parameters during init (start-up).

Some possible explanations why the error has occurred:

- Refer to error description for C CC 008 100

C CC 008 104 ERROR READING PARAMETERS FOR COND A TEMP.

Unconditional error, blood pump not available

General description of conditions for occurring:

- An error occurred while reading transducer parameters during init (start-up).

Some possible explanations why the error has occurred:

- No connection between transducer and MM95 I/O board
- Incorrect connection between transducer and MM95 I/O board
- No connection between MM95 I/O and control CPU board
- Incorrect transducer ID. Update transducer ID (I2C scan).
- EEPROM on transducer board is broken
- Serial bus error on control CPU board, or I/O SIMM problem (P310)
- Uncalibrated transducer. Calibrate transducer
- Broken MM95 I/O board

C CC 008 105 ERROR READING PARAMETERS FOR COND A TEMP. (HEAT)

Unconditional error, blood pump not available

General description of conditions for occurring:

- An error occurred while reading transducer parameters during init (start-up).

Some possible explanations why the error has occurred:

- Refer to error description for C CC 008 104

HCEN 9091 Page 9 of 106

C CC 008 106 ERROR READING PARAMETERS FOR COND A
Unconditional error, blood pump not available

General description of conditions for occurring:

- An error occurred while reading transducer parameters during init (start-up).

Some possible explanations why the error has occurred:

- Refer to error description for C CC 008 104

C CC 008 107 ERROR READING PARAMETERS FOR COND B TEMP.

Unconditional error, blood pump not available

General description of conditions for occurring:

- An error occurred while reading transducer parameters during init (start-up).

Some possible explanations why the error has occurred:

- Refer to error description for C CC 008 104

C CC 008 108 ERROR READING PARAMETERS FOR COND B TEMP. (HEAT)

Unconditional error, blood pump not available

General description of conditions for occurring:

- An error occurred while reading transducer parameters during init (start-up).

Some possible explanations why the error has occurred:

- Refer to error description for C CC 008 104

C CC 008 109 ERROR READING PARAMETERS FOR COND B

Unconditional error, blood pump not available

General description of conditions for occurring:

- An error occurred while reading transducer parameters during init (start-up).

Some possible explanations why the error has occurred:

- Refer to error description for C CC 008 104

C CC 008 110 ERROR READING PARAMETERS FOR MM95 A/D REF

Unconditional error, blood pump not available

General description of conditions for occurring:

- An error occurred while reading transducer parameters during init (start-up).

Some possible explanations why the error has occurred:

- No connection between MM95 I/O and control CPU board
- Incorrect transducer ID. Update transducer ID (I2C scan).
- EEPROM on transducer board is broken
- Serial bus error on control CPU board, or I/O SIMM problem (P310)
- Uncalibrated transducer. Calibrate transducer
- Broken MM95 I/O board

C CC 008 111 ERROR READING PARAMETERS FOR VENOUS PRESSURE

Unconditional error, blood pump not available

General description of conditions for occurring:

- An error occurred while reading transducer parameters during init (start-up).

Some possible explanations why the error has occurred:

- No connection between transducer board and BM I/O board
- No connection between BM I/O board and control driver board

HCEN 9091 Page 10 of 106

- Transducer board mounted in incorrect position on BM I/O board
- Incorrect transducer ID. Update transducer ID (I2C scan).
- EEPROM on transducer board is broken
- Serial bus error on control CPU board, or I/O SIMM problem (P310
- Uncalibrated transducer. Calibrate transducer
- Broken BM I/O board

C CC 010, A/D Conversion

C CC 010 000 CASE ERROR
Transient error

General description of conditions for occurring:

- Internal software error

C CC 010 001 A/D CONVERTER BUFFER POINTER ERROR

Unconditional error, blood pump not available

General description of conditions for occurring:

- Data have not been read from A/D converter (IC 20) on the control driver
board.

Technical description of conditions for occurring:

- The A/D converter interrupt function should have stored A/D converter data
in a buffer and should have changed the value of adInPtr to a value that is not
the same as adOutPtr. The A/D converter interrupt routine had not executed.

Some possible explanations why the error has occurred

- The A/D converter IC 20 on the control driver is broken
- The PAL IC 28 on the control CPU board is broken
- The inverter IC 4 on the control driver board is broken
- The interrupt controller IC 52 on the control CPU board is broken (N.E.: the
CPU IC 10 on control CPU board is broken)

C CC 010 002 AK 95 A/D CONVERTER OFFSET ERROR

Unconditional error, blood pump not available

General description of conditions for occurring:

- The zero voltage value was outside limits

Some possible explanations why the error has occurred:

- A/D converter IC 20 on control driver board is broken

C CC 010 003 AK 95 A/D CONVERTER REFERENCE ERROR

Unconditional error, blood pump not available

General description of conditions for occurring:

- The reference voltage value was outside limits

Some possible explanations why the error has occurred:

- A/D converter IC 20 on control driver board is uncalibrated
- A/D converter IC 20 on control driver board is broken

C CC 010 004 AK 95 AD REFERENCE VOLTAGE INIT ERROR

Unconditional error, blood pump not available

General description of conditions for occurring:

- The CPU C A/D converter reference value was corrupt

HCEN 9091 Page 13 of 106

Unconditional error, blood pump available

General description of conditions for occurring:

- High pressure in monitor during SAGS test. Main flow through RIVA.

Technical description of conditions for occurring:

- FRI(FI_HPGPr)>450mmHg for more than 5 seconds

Some possible explanations why the error has occurred:

- RIVA unable to open
- Fluid path obstruction
- HPG broken/uncalibrated

C CFF 006 002 HIGH PRESSURE DURING FUNCTION CHECK

Unconditional error, blood pump available

General description of conditions for occurring:

- High pressure in monitor during function check

Technical description of conditions for occurring:

- FRI(FI_HPGPr)>450mmHg for more than 1,5 seconds

Some possible explanations why the error has occurred:

- Fluid path obstruction
- HPG broken/uncalibrated

C CFF 006 003 UNSTABLE DEGASSING PRESSURE

Unconditional error, blood pump available

General description of conditions for occurring:

- Unstable degassing pressure during function check. The degassing pressure
has been measured twice with an interval of 15 seconds. The difference
between the two measurements was more than 20mmHg

Technical description of conditions for occurring:

- oldDegassPr - FRI(FI_DegassPr) ) < -20mmHg
or
- oldDegassPr - FRI(FI_DegassPr) ) > 20mmHg

Some possible explanations why the error has occurred:

Technical description of conditions for occurring:

- FRI(FI_FlowPumpCurren) > 1500mA

Some possible explanations why the error has occurred:

HCEN 9091 Page 17 of 106

- Pump motor broken
- Broken control driver board (R10, R11, R13, C20)
- Broken control driver board A/D system (IC17, IC18, IC20 and components)

C CFS 009, Flow Pump Regulator, Service Mode

C CFS 009 000 CASE ERROR
Transient error

General description of conditions for occurring:

- Internal software error

C CFS 009 001 FLOW PUMP CURRENT ERROR

Unconditional error, blood pump available

General description of conditions for occurring:

- Flow pump current too low

Technical description of conditions for occurring:

- FRI(FI_FlowPumpCurrent) < 50mA

Some possible explanations why the error has occurred:

C CFS 009 002 DEGASS PRESSURE CONTROL ERROR

Unconditional error, blood pump available

General description of conditions for occurring:

- The flow pump could not create the preset degassing pressure

Technical description of conditions for occurring:

- FRI(FI_DegassPr) > -(EI(EEI_DegassPr)-60)mmHg

Some possible explanations why the error has occurred:

C CFS 009 004 UNSTABLE MAIN FLOW

Unconditional error, blood pump available

General description of conditions for occurring:

- Unstable main flow during UF cell calibration

Technical description of conditions for occurring:

- The main flow has been outside limit (+/- 5ml/min)

Some possible explanations why the error has occurred:

- Broken UFcell
- Leakage in fluid path

HCEN 9091 Page 18 of 106

- Air in fluid path
- The flow pump is decoupled. FRL(F_FlowPumpDecoupl)=TRUE
( The flow pump could not follow the flow pump motor rotation. The
magnetic coupling disconnected the pump from the motor. The pump
might be dirty or the flow path might be blocked).
- Broken control driver board (IC24, L2, Q1 and components)
- Broken control CPU board (IC32) (N.E.: Broken control CPU board, IC10)

C CFT 009, Flow Pump Regulator, Treatment Mode

C CFT 009 000 CASE ERROR
Transient error

General description of conditions for occurring:

- Internal software error

C CFT 009 001 DEGASS PRESSURE CONTROL ERROR

Unconditional error, blood pump available

General description of conditions for occurring:

- The flow pump could not create the preset degassing pressure

Technical description of conditions for occurring:

- FRI(FI_DegassPr) > -(EI(EEI_DegassPr)-60)mmHg

Some possible explanations why the error has occurred:

C CFT 009 002 FLOW PUMP CURRENT ERROR

Unconditional error, blood pump available

General description of conditions for occurring:

- Flow pump current too low

Technical description of conditions for occurring:

- FRI(FI_FlowPumpCurrent) < 50mA

Technical description of conditions for occurring:

- PRL(P_BubbleTrapHigh)=FALSE

Some possible explanations why the error has occurred:

- The AIVA or REVA could not be opened

HCEN 9091 Page 21 of 106

- Broken float in bubble chamber
- Broken protective driver board (IC28)

C CFF 018 006 NOT POSIBLE TO REGULATE HPG PRESSURE

Unconditional error, blood pump available

General description of conditions for occurring:

- Impossible to regulate HPG to -100mmHg in AIVA test (120 sec. test-time)

Technical description of conditions for occurring:

- FRI(FI_HPGPR) could not be regulated to -100mmHg

Some possible explanations why the error has occurred:

- Air in fluid path
- Broken suction pump
- Broken control CPU board (IC4, IC5, Q12 and components)

C CFF 018 007 CURRENT TEST ERROR , FIVA VALVE (1)

Unconditional error, blood pump available

General description of conditions for occurring:

- The current through FIVA valve has been measured with valve closed and
then with valve opened, despite the UFD has been preseted NotInst. The current
difference has been large enough in order to detect that FIVA valve is installed

Technical description of conditions for occurring:

- FRI(FI_ValvesCurrent)-refCurrent > 200mA and not EL(EEL_UfdInstalled).

Some possible explanations why the error has occurred:

- The UFD has been preseted NotInst instead of Inst, despite the FIVA valve
and consequently the UFD is installed

C CFF 018 008 CURRENT TEST ERROR , FIVA VALVE (2)

Unconditional error, blood pump available

General description of conditions for occurring:

- The current through FIVA valve has been measured with valve closed and
then with valve opened, with the UFD preseted Inst. The current difference has
not been large enough.

Technical description of conditions for occurring:

- FRI(FI_ValvesCurrent)-refCurrent < 200mA and EL(EEL_UfdInstalled).

Some possible explanations why the error has occurred:

- Broken/unconnected magnet on FIVA valve.
- Broken control driver board (Q10, V12).
- The UFD has been preseted Inst instead of NotInst, despite there is no FIVA
valve and consequently no UFD installed

C CFD 018 009 CURRENT TEST ERROR, DRVA VALVE

Unconditional error, blood pump available
General description of conditions for occurring:
- The current through the DRVA valve has been measured with valve closed
and then with valve opened. The current difference is too big
Technical description of conditions for occurring:
- FRI(FI_ValvesCurrent) - refCurrent > 200mA
Some possible explanations why the error has occurred:
- Broken control driver board
- DRVA is connected and the preset “Set flow installed” is set to “installed”.

HCEN 9091 Page 22 of 106

C CFT 018, Valve Current Measuring, Function Check
C CF 018 000 CASE ERROR
Transient error

General description of conditions for occurring:

- Internal software error

C CFT 018 001 CURRENT TEST ERROR, DRVA VALVE

Unconditional error, blood pump available

General description of conditions for occurring:

- The current through the DRVA valve has been measured with valve closed
and then with valve opened. The current difference has not been large enough.
- This error code is not used in program version 3.00 and later

Technical description of conditions for occurring:

- FRI(FI_ValvesCurrent) - refCurrent < 200mA

Some possible explanations why the error has occurred:

- Broken/unconnected magnet on DRVA valve
- Broken control driver board (Q4, V3)

C CFT 018 002 CURRENT TEST ERROR, AIVA VALVE

Unconditional error, blood pump available

General description of conditions for occurring:

- The current through the AIVA valve has been measured with valve closed
and then with valve opened. The current difference has not been large enough.
- This error code is not used in program version 3.00 and later

Technical description of conditions for occurring:

- FRI(FI_ValvesCurrent) - refCurrent < 200mA

Some possible explanations why the error has occurred:

- Broken/unconnected magnet on AIVA valve
- Broken control driver board (Q2, V2)

C CFT 018 003 BUBBLE CHAMBER (DEAIRATING CHAMBER) ERROR

Unconditional error, blood pump available

General description of conditions for occurring:

- AIVA and REVA opened. Suction pump active and fluid tubes connected to
safety bypass. Low level in bubble chamber is not achieved within 90 sec.
NOTE: This error code is not used in programs later than version P2.04.

Technical description of conditions for occurring:

- PRL(P_BubbleTrapLow)=FALSE after 90 seconds

Some possible explanations why the error has occurred:

- The AIVA or REVA could not be opened
- Broken float in bubble chamber
- Broken protective driver board (IC28)

C CFD 020, Flow Meter, Disinfection Mode

C CFD 020 000 CASE ERROR
Transient error

HCEN 9091 Page 23 of 106

General description of conditions for occurring:
- Internal software error

C CFF 020, Flow Meter, Function Check

C CFF 020 000 CASE ERROR
Transient error

General description of conditions for occurring:

- Internal software error

C CFM 020, Flow Meter

C CFM 020 000 CASE ERROR
Transient error

General description of conditions for occurring:

- Internal software error

C CFM 020 002 UF TIMER ERROR

Unconditional error, blood pump available

General description of conditions for occurring:

- The UF timer is not working properly.

Technical description of conditions for occurring:

- The timer 9513 has returned error message(s).

Some possible explanations why the error has occurred:

- The timer IC 34 on the control driver board is broken.

C CFM 020 003 VFC CHANNEL 1 PULSE COUNTER OVERFLOW

Unconditional error, blood pump available

General description of conditions for occurring:

- The pulse counter for VFC channel 1 has counted up to its max. value

Some possible explanations why the error has occurred:

- The VFC, (voltage to frequency) IC 14 on control driver board, or some
component around it, is broken.

C CFM 020 004 VFC CHANNEL 2 PULSE COUNTER OVERFLOW

Unconditional error, blood pump available

General description of conditions for occurring:

- The pulse counter for VFC channel 2 has counted up to its max. value

Some possible explanations why the error has occurred:

- The VFC, (voltage to frequency) IC 15 on control driver board, or some
component around it is broken

C CFM 020 005 UF TIMER ERROR

Unconditional error, blood pump available

General description of conditions for occurring:

- The UF timer is not working properly.

Technical description of conditions for occurring:

- The timer 9513 has returned error message(s).

HCEN 9091 Page 24 of 106

Some possible explanations why the error has occurred:
- The timer IC 34 on the control driver board is broken.

C CFM 020 006 VFC CHANNEL 1 REFERENCE MEASUREMENT ERROR

Unconditional error, blood pump available

General description of conditions for occurring:

- The VFC channel 1 has been connected to the reference voltage. The pulse
counter (IC23 counter 3, control driver board) has measured a frequency that
differs too much from the frequency that usually is measured when the
reference voltage is connected.

Technical description of conditions for occurring:

VFC1.VALUE > 0.86241*VFC1.OFFSET for 2s
OR
VFC1.VALUE < 0.82859*VFC1.OFFSET for 2s

VFC1.OFFSET = VFC value when 0V is connected.

Some possible explanations why the error has occurred:

- The VFC, (voltage to frequency) IC 14 on control driver board, or some
component around it is broken
- IC 23 broken (control driver board)

C CFM 020 007 VFC CHANNEL 2 REFERENCE MEASUREMENT ERROR

Unconditional error, blood pump available

General description of conditions for occurring:

- The VFC channel 2 has been connected to the reference voltage. The pulse
counter (IC23 counter 4, control driver board) has measured a frequency that
differs too much from the frequency that usually is measured when the
reference voltage is connected.

Technical description of conditions for occurring:

VFC2.VALUE > 0.86241*VFC2.OFFSET for 2s
OR
VFC2.VALUE < 0.82859*VFC2.OFFSET for 2s

VFC2.OFFSET = VFC value when 0V is connected.

Some possible explanations why the error has occurred:

- The VFC, (voltage to frequency) IC 15 on control driver board, or some
component around it is broken
- IC 23 broken (control driver board)

C CFM 020 008 VFC CHANNEL 1 OFFSET MEASUREMENT ERROR

Unconditional error, blood pump available

General description of conditions for occurring:

- The VFC channel 1 has been connected to 0V. The pulse counter has
measured a frequency that differs too much from the frequency that usually is
measured when 0V is connected.

Technical description of conditions for occurring:

VFC1.VALUE has been outside the allowed interval 6907-10907 for 2s

Some possible explanations why the error has occurred:

- The VFC, (voltage to frequency) IC 14 on control driver board, or some
component around it is broken
- IC 23 broken (control driver board)

HCEN 9091 Page 25 of 106

C CFM 020 009 VFC CHANNEL 2 OFFSET MEASUREMENT ERROR
Unconditional error, blood pump available

General description of conditions for occurring:

- The VFC channel 2 has been connected to 0V. The pulse counter has
measured a frequency that differs too much from the frequency that usually is
measured when 0V is connected.

Technical description of conditions for occurring:

VFC2.VALUE has been outside the allowed interval 6907-10907 for 2s

Some possible explanations why the error has occurred:

- The VFC, (voltage to frequency) IC 15 on control driver board, or some
component around it is broken
- IC 23 broken (control driver board)

C CFM 020 010 MEASURED MAGNETIZATION CURRENT INCORRECT

Unconditional error, blood pump available

General description of conditions for occurring:

- Measured magnetization current differs to much from typical value.

Technical description of conditions for occurring:

- UF coil current is outside the limits 0.18 A - 0.28 A for 5 seconds.

Some possible explanations why the error has occurred:

- UF cell broken
- Bad connection between UF cell and control driver board
- Broken control driver board

C CFM 020 011 UF CELL TARATION NOT APPROVED

Unconditional error, blood pump available

General description of conditions for occurring:

- A self calibration (taration) was run. It failed as the values of the variables
FRR(FR_UFRTOLERANCE) and FRR(FR_UFROFFSET) had changed too
much since the last self calibration. A new self calibration was run after 5
minutes. It did also fail for the same reason.

Technical description of conditions for occurring:

- CalibrDiffFlowNew differed more than 1 ml/min from CalibrDiffFlowOld
A new self calibration was done after 5 minutes.
CalibrDiffFlow again differed more than 1.0 ml/min from CalibrDiffFlowNew
AND CalibrDiffFlow again differed more than 1.0 ml/min from
CalibrDiffFlowOld

Some possible explanations why the error has occurred:

- UF cell broken or dirty
- There is air through the UF cell
- Leakage through: RIVA, ZEVA, DIVA or TAVA

C CFM 020 012 UF CELL TARATION NOT APPROVED

Unconditional error, blood pump available

General description of conditions for occurring:

- A self calibration (taration) was run. It failed as the value of the variable
FRR(FR_UFRTOLERANCE) differed too much from the value that was
stored in the EEPROM or estimated at the last performed self
calibration.

HCEN 9091 Page 26 of 106

Technical description of conditions for occurring:
CALIBR DIFF FLOWnew differed more than 7.5 ml/min from CALIBR DIFF
FLOWold

Some possible explanations why the error has occurred:

- UF cell broken or dirty
- There is air through the UF cell
- Leakage through: RIVA, ZEVA, DIVA or TAVA

C CFM 020 014 TOO LOW SELF CALIBRATION FLOW

Unconditional error, blood pump available

General description of conditions for occurring:

- The flow measuring unit measured a flow through channel 1 that was less
than 100 ml/min during self calibration (taration).

Technical description of conditions for occurring:

- FRR(FR_CH1RATE) < 100.0 ml/min.

Some possible explanations why the error has occurred:

- Uncalibrated or broken. pressure regulator
- Dirty flow restrictor.
- Dirty outlet restrictor
- Dirty or broken flow pump:.
- Dirty or broken suction pump.
- Broken or uncalibrated degassing pressure transducer.
- ZEVA: leakage
- RIVA: leakage

C CFM 020 015 UNSTABLE FLOW SIGNALS DURING SELF CALIBRATION

Unconditional error, blood pump available

General description of conditions for occurring:

- The self calibration (taration) failed because at least one of the measured flow
signals varied too much. A new self calibration that was done 5 minutes later
did also fail because at least one of the measured flow signals varied too much.

Technical description of conditions for occurring:

- Variance of the flow signals were calculated
The differential flow during either the offset calibration or during the
differential flow varied too much

Some possible explanations why the error has occurred:

- Air is flowing through flow channel 1. There is too much air in the inlet water
- Valves: RIVA, ZEVA, diva or TAVA are leaking
- Flow cell: the flow cell is dirty.
- Flow cell: the flow cell is broken
- Flow restrictor: the restrictor is dirty
- Flow pump: the pump is not working properly
- Degassing chamber: the o-ring at the top of the chamber is not in its correct
position. fluid is leaking.
- Degassing pressure transducer: not working properly.

C CFM 020 016 SELF CALIBRATION TIME OUT

Unconditional error, blood pump available

General description of conditions for occurring:

- The self calibration (taration) executed for a too long time.

HCEN 9091 Page 27 of 106

Technical description of conditions for occurring:
- Self calibration time > max. self calibration time (max. self calibration time =
15s - 68s)

Some possible explanations why the error has occurred:

- Secondary error to the error C CFM 020 006
- Secondary error to the error C CFM 020 007
- Secondary error to the error C CFM 020 008
- Secondary error to the error C CFM 020 009.

C CFM 020 017 VFC CALIBRATION TIME OUT (VFC1 OFFSET).

Unconditional error, blood pump available

General description of conditions for occurring:

- Please refer to the description of C CFM 020 008

C CFM 020 018 VFC CALIBRATION TIME OUT (VFC2 OFFSET).

Unconditional error, blood pump available

General description of conditions for occurring:

- Please refer to the description of C CFM 020 009

C CFM 020 019 VFC CALIBRATION TIME OUT (VFC1 REFERENCE).

Unconditional error, blood pump available

General description of conditions for occurring:

- Please refer to the description of C CFM 020 006

C CFM 020 020 VFC CALIBRATION TIME OUT (VFC2 REFERENCE).

Unconditional error, blood pump available

General description of conditions for occurring:

- Please refer to the description of C CFM 020 007

C CFM 020 021 MEASURED MAGNETIZATION CURRENT INCORRECT

Unconditional error, blood pump available

General description of conditions for occurring:

- Please refer to the description of C CFM 020 010

C CFM 020 024 UNSTABLE SIGNAL DURING UF CELL CALIBRATION

General description of conditions for occurring:

- The UF cell calibration failed because at least one of the measured flow
signals varied too much

Unconditional error, blood pump available

General description of conditions for occurring:

- The UF pulse timer is not working properly.

Technical description of conditions for occurring:

- The timer 9513 has returned error message(s).

Some possible explanations why the error has occurred:

- The timer IC 34 on the control driver board is broken.

Technical description of conditions for occurring:

- Variance of the flow signals were calculated
The flow through one or both of the UF channels during the differential flow
calibration stage varied too much.

- Internal software error

C CFT 026, UF Volume Accumulation, Treatment Mode

C CFT 026 000 CASE ERROR
Transient error

C CO 069 000 CASE ERROR
Transient error

General description of conditions for occurring:

- Internal software error

C CO 072, Conductivity
C CO 072 000 CASE ERROR
Transient error

General description of conditions for occurring:

- Internal software error

C CO 073, Conductivity Profiling

C CO 073 000 CASE ERROR
Transient error

General description of conditions for occurring:

- Internal software error

C CO 073 001 CASE ERROR

Transient error

General description of conditions for occurring:

- Internal software error

C CO 073 002 CASE ERROR

Transient error

HCEN 9091 Page 43 of 106

General description of conditions for occurring:
- Internal software error

C CO 074, UF Profiling
C CO 074 000 CASE ERROR
Transient error

General description of conditions for occurring:

C CO 096, Profiling
C CO 096 000 CASE ERROR
Transient error

General description of conditions for occurring:

- Internal software error
C COxx 071, WRO 300 H communication
C COFF 071 000 CASE ERROR
Transient error

General description of conditions for occurring:

HCEN 9091 Page 45 of 106

- Internal software error

C COFF 071 001 Error in output signal to CPU

Transient error

General description of conditions for occurring:

Internal software error

C COFF 071 002 Logical error in communication protocol

Transient error

General description of conditions for occurring:

Internal software error

C COxx 088, Functional Check

C CO 088 000 CASE ERROR
Transient error

General description of conditions for occurring:

- Internal software error

C COFB 088 001 AIR DETECTOR TEST ERROR, CPU P

Unconditional error, blood pump not available

General description of conditions for occurring:

- CPU P air detector does not detect “air” when the transmitted intensity is
lowered during Fch.

Technical description of conditions for occurring:

- PRI(PI_AirDetAirPErrCnt) > 10

Some possible explanations why the error has occurred:

- Air detector broken
- Broken BM I/O board (IC5, IC14 and components, IC12, IC17, Q6, Q7, IC19
and components)
- Broken protective CPU board (IC43 and components) (N.E. IC48)
- Broken protective driver board (IC6 and components, V6 and components,
IC4 and components, IC55)

C COFB 088 002 AIR DETECTOR TEST ERROR, CPU W

Unconditional error, blood pump not available

General description of conditions for occurring:

- CPU W air detector does not detect “air” when the transmitted intensity is
lowered during Fch.

Technical description of conditions for occurring:

- PRI(PI_AirDetAirWErrCnt) > 10

Some possible explanations why the error has occurred:

- Air detector broken
- Broken BM I/O board (IC5, IC14 and components, IC12, IC17, Q6, Q7, IC19
and components)
- Broken protective CPU board (IC3 and components)
- Broken protective driver board (IC2 and components, V3 and components,

HCEN 9091 Page 46 of 106

IC1 and components, IC55)

C COFB 088 003 AIR DETECTOR TEST ERROR, CPU P AND W

Unconditional error, blood pump not available

General description of conditions for occurring:

- One or both of CPU P and CPU W’s air detectors does not sense alarm free
status when the transmitted intensity is increased to normal level. This error
code should only occure if anything is done with the air detector during the low
intensity test phase, since this condition (alarm free status) was already fulfilled
at the start of the test.

Technical description of conditions for occurring:

- PRI(PI_AirDetNoAirErrCnt) > 10

Some possible explanations why the error has occurred:

- Low level in venous drip chamber. Check the level and restart the monitor.

C COFF 088 004 BLOOD LEAK DETECTOR TEST ERROR, VALUE TOO HIGH
Unconditional error, blood pump available

General description of conditions for occurring:

- The blood leak detector value is too high when the LED is off.

Technical description of conditions for occurring:

- PRI(PI_BlLeakOffLevelErrCnt) > 4
- Blood leak detector value > 2mV measured by ADC (CPU P)

Some possible explanations why the error has occurred:

- Blood leak detector uncalibrated
- Blood leak detector unit broken
- Too much external light in blood leak detector ( AK 95 open for service)
- Broken protective driver board (R71 and components, IC29, IC25)
- Broken/uncalibrated A/D system, protective driver board (IC12, IC13, IC15,
and components)

C COFF 088 005 BLOOD LEAK DETECTOR TEST ERROR, VALUE OUT OF LIMIT
Unconditional error, blood pump available

General description of conditions for occurring:

- The blood leak detector value is out of the limits when the LED is lit

Technical description of conditions for occurring:

- PRI(PI_BlLeakOnLevelErrCnt) > 4
- Blood leak detector value < -10 or blood leak detector value > +60
(AK95P.CPU_P.SUP.MEAS.AD_INPUT.blLeakValue)

Some possible explanations why the error has occurred:

- Blood leak detector uncalibrated
- Blood leak detector dirty
- Blood leak detector broken
- Broken protective driver board (R71 and components, IC29, IC25)
- Broken/uncalibrated A/D system, protective driver board (IC12, IC13, IC15,
and components)

C COFF 088 006 BLOOD LEAK DETECTOR TEST ERROR, UNSTABLE OFF
Unconditional error, blood pump available

General description of conditions for occurring:

The blood leak detector value is unstable when the LED is turned off.

HCEN 9091 Page 47 of 106

Technical description of conditions for occurring:
- PRI(PI_BlLeakOffStableErrCnt) > 4
- Blood leak detector variance >5

Some possible explanations why the error has occurred:

- Blood leak detector broken
- Broken protective driver board (R71 and components, IC29, IC25)
- Broken/uncalibrated A/D system, protective driver board (IC12, IC13, IC15,
and components)

C COFF 088 007 BLOOD LEAK DETECTOR TEST ERROR, UNSTABLE ON

Unconditional error, blood pump available

General description of conditions for occurring:

The blood leak detector value is unstable when the LED is turned on.

Technical description of conditions for occurring:

- PRI(PI_BlLeakOnStableErrCnt) > 4
- Blood leak detector variance >5

Some possible explanations why the error has occurred:

- Blood leak detector broken
- Broken protective driver board (R71 and components, IC29, IC25)
- Broken/uncalibrated A/D system, protective driver board (IC12, IC13, IC15,
and components)

C COFB 088 008 BLOOD PUMP TEST ERROR, PUMP NOT RUNNING (FIRST TEST)
Unconditional error, blood pump not available

General description of conditions for occurring:

- The blood pump was commanded to run. The blood pump tacho value is too
low AND the rotation indicator is not detecting movement (first check).

Technical description of conditions for occurring:

- PRI(PI_BlPumpEdge1ErrCnt) > 10

Some possible explanations why the error has occurred:

- Blood pump not connected to BM I/O board, P602
- Pump rotation indicator (P605) AND tacho (P604) not connected to BM I/O
- Blood pump electronics broken (BM I/O IC7, IC3, IC11, IC8, Q1-4 and
components).

C COFB 088 009 BLOOD PUMP TEST ERROR, PUMP NOT RUNNING (SECOND TEST)
Unconditional error, blood pump not available

General description of conditions for occurring:

- The blood pump was commanded to run. The blood pump tacho value is too
low AND the rotation indicator is not detecting movement (second check).

Technical description of conditions for occurring:

- PRI(PI_BlPumpEdge2ErrCnt) > 4

Some possible explanations why the error has occurred:

C COFB 088 010 BLOOD PUMP TEST ERROR, PUMP NOT STOPPED (CPU P)

HCEN 9091 Page 48 of 106

Unconditional error, blood pump not available

General description of conditions for occurring:

- The blood pump was commanded to stop by CPU P. The measured values
from tacho and/or rotation indicator show that the blood pump is still running.

Technical description of conditions for occurring:

- PRI(PI_BlPumpPStopErrCnt) > 4

Some possible explanations why the error has occurred:

- Broken BM I/O board, IC11 and components
- Broken protective driver board, IC 32

C COFB 088 011 BLOOD PUMP TEST ERROR, PUMP NOT RUNNING
ROTATION INDICATOR, (FIRST CHECK)
Unconditional error, blood pump not available

General description of conditions for occurring:

- The blood pump was commanded to run. The blood pump tacho value is OK
but the rotation indicator has not detected any movement (first check)

Technical description of conditions for occurring:

- PRI(PI_BlPumpRotate1ErrCnt) > 10

Some possible explanations why the error has occurred:

- The rotation indicator is broken or unconnected to BM I/O board (P605)
- Broken BM I/O board (Z3, R51, R47)
- Broken protective driver board, IC39

C COFB 088 012 BLOOD PUMP TEST ERROR, PUMP NOT RUNNING
ROTATION INDICATOR, (SECOND CHECK)
Unconditional error, blood pump not available
Unconditional error, blood pump not available

General description of conditions for occurring:

- The blood pump was commanded to run. The blood pump tacho value is OK
but the rotation indicator has not detected any movement (first check)

Technical description of conditions for occurring:

- PRI(PI_BlPumpRotate2ErrCnt) > 4

Some possible explanations why the error has occurred:

- The rotation indicator is broken or unconnected
- Broken BM I/O board (Z3, R51, R47)
- Broken protective driver board, IC39

C COFB 088 013 BLOOD PUMP TEST ERROR, PUMP NOT RUNNING
TACHO SIGNALS MISSING, (FIRST CHECK)
Unconditional error, blood pump not available

General description of conditions for occurring:

- The blood pump was commanded to run. The blood pump rotation indicator
has detected movement but tacho value is too low (first check)

Technical description of conditions for occurring:

- PRI(PI_BlPumpTach1ErrCnt) > 10

Some possible explanations why the error has occurred:

- Blood pump tacho broken or unconnected to BM I/O board (P604)
- Broken control driver board (IC34)

HCEN 9091 Page 49 of 106

C COFB 088 014 BLOOD PUMP TEST ERROR, PUMP NOT RUNNING
TACHO SIGNALS MISSING, (SECOND CHECK)
Unconditional error, blood pump not available

General description of conditions for occurring:

- The blood pump was commanded to run. The blood pump rotation indicator
has detected movement but tacho value is to low (second check)

Technical description of conditions for occurring:

- PRI(PI_BlPumpTach2ErrCnt) > 4

Some possible explanations why the error has occurred:

- Blood pump tacho broken or unconnected to BM I/O board (P604)
- Broken control driver board (IC34)

C COFB 088 015 BLOOD PUMP TEST ERROR, PUMP NOT STOPPED (CPU W)
Unconditional error, blood pump not available

General description of conditions for occurring:

- The blood pump was commanded to stop by CPU W. The measured values
from tacho and/or rotation indicator show that the blood pump is still running.

Technical description of conditions for occurring:

- PRI(PI_BlPumpWStopErrCnt) > 4

Some possible explanations why the error has occurred:

- Broken BM I/O board (IC1, IC15)
- Broken protective CPU board (IC10, IC7, IC5) (N.E.: IC10, IC7, IC6)

C COFB 088 016 COMMUNICATION ERROR BETWEEN CPU W AND P (BM1)

Unconditional error, blood pump not available

General description of conditions for occurring:

- CPU W does not agree on that the blood monitor function check part 1 is
ready

Technical description of conditions for occurring:

- PRI(PI_Bm1ErrCnt) > 2

Some possible explanations why the error has occurred:

- Broken protective CPU board (IC26, V4 and components)

C COFB 088 017 COMMUNICATION ERROR BETWEEN CPU W AND P (BM1)

Unconditional error, blood pump not available

General description of conditions for occurring:

- CPU W does not agree on that the blood monitor function check part 2 is
ready

Technical description of conditions for occurring:

- PRI(PI_Bm2ErrCnt) > 2

Some possible explanations why the error has occurred:

- Broken protective CPU board (IC26, V4 and components)

C COFB 088 018 BUZZER TEST ERROR, BUZZER NOT ON (CPU P)

Unconditional error, blood pump not available

General description of conditions for occurring:

HCEN 9091 Page 50 of 106

- The microphone can not detect that the CPU P buzzer is on

Technical description of conditions for occurring:

- PRI(PI_BuzzPOnErrCnt) > 3

Some possible explanations why the error has occurred:

- CPU P buzzer is broken (H2 on protective driver board)
- Protective driver board broken (IC39, IC21, IC16, M1(microphone), IC5, V8,
V7 and components)

It is not possible to mute buzzer

C COFB 088 019 BUZZER TEST ERROR, BUZZER NOT OFF (CPU P)
Unconditional error, blood pump not available

General description of conditions for occurring:

- The microphone can not detect that the CPU P buzzer is off

Technical description of conditions for occurring:

- PRI(PI_BuzzPOffErrCnt) > 3

Some possible explanations why the error has occurred:

- Protective driver board broken (IC39, IC21, IC16, M1(microphone), IC5, V8,
V7 and components)

It is not possible to mute buzzer

C COFB 088 020 BUZZER TEST ERROR, BUZZER NOT SILENT

Unconditional error, blood pump not available

General description of conditions for occurring:

- The microphone can not detect that both the CPU P and the CPU W buzzer
are off when the buzzer test starts

Technical description of conditions for occurring:

- PRI(PI_BuzzSilentErrCnt) > 3

Some possible explanations why the error has occurred:

- Protective driver board broken (M1 (microphone), IC5, V8, V7 and
components)

It is not possible to mute buzzer

C COFB 088 021 BUZZER TEST ERROR, BUZZER NOT ON (CPU W)

Unconditional error, blood pump not available

General description of conditions for occurring:

- The microphone can not detect that the CPU W buzzer is on

Technical description of conditions for occurring:

- PRI(PI_BuzzWOnErrCnt) > 3

Some possible explanations why the error has occurred:

- CPU W buzzer is broken (H1 on protective CPU board)
- Protective CPU board is broken (IC10, IC7)
- Protective driver board broken (M1(microphone), IC5, V8, V7 and
components)

It is not possible to mute buzzer

HCEN 9091 Page 51 of 106

C COFB 088 022 BUZZER TEST ERROR, BUZZER NOT OFF (CPU W)
Unconditional error, blood pump not available

General description of conditions for occurring:

- The microphone can not detect that the CPU W buzzer is off

Technical description of conditions for occurring:

- PRI(PI_BuzzWOffErrCnt) > 3

Some possible explanations why the error has occurred:

- Protective CPU board is broken (IC10, IC7)
- Protective driver board broken (M1(microphone), IC5, V8, V7 and
components)

It is not possible to mute buzzer

C COFB 088 023 COMMUNICATION ERROR BETWEEN CPU W AND P (COM)

Unconditional error, blood pump not available

General description of conditions for occurring:

- CPU W does not agree on that the common function check is ready

Technical description of conditions for occurring:

- PRI(PI_ComErrCnt) > 2

Some possible explanations why the error has occurred:

- Broken protective CPU board (IC26, V4 and components)

C COFF 088 024 CONDUCTIVITY TEST ERROR,

CONDUCTIVITY COMPARE ERROR (HIGH CONDUCTIVITY TEST)
Unconditional error, blood pump available

General description of conditions for occurring:

- The conductivity difference between CPU C and CPU P is too large in the
conductivity test high phase.
- The difference between CondA (FRI(FI_MM90CONDA)) and CondP
(AK95P.CPU_P.SUP.MEAS.AD_INPUT.condValue) is outside limit +/-
1mS/cm

- The difference between CondA (FRI(FI_MM90CONDA)) and CondB

(FRI(FI_MM90CONDB))
(AK95P.CPU_P.SUP.MEAS.AD_INPUT.condValue) is outside limit +/-
0.3mS/cm

Technical description of conditions for occurring:

- PRI(PI_CondHighDiffErrCnt) > 4
- The difference between CondB (FRI(FI_MM90CONDB)) and CondP
(AK95P.CPU_P.SUP.MEAS.AD_INPUT.condValue) is outside limit +/-
1mS/cm

Some possible explanations why the error has occurred:

- Conductivity cell B is broken or uncalibrated
- Conductivity cell P is broken or uncalibrated
- Conductivity cell A is broken or uncalibrated
- The A/D converters are uncalibrated (CPU P, MM 95)

C COFF 088 025 CONDUCTIVITY TEST ERROR,

CONDUCTIVITY VALUE TOO LOW (HIGH CONDUCTIVITY TEST)
Unconditional error, blood pump available

HCEN 9091 Page 52 of 106

General description of conditions for occurring:
- The conductivity measured by CPU P is not high enough in the conductivity
test high phase.

Technical description of conditions for occurring:

- PRI(PI_CondHighLevelErrCnt) > 4
- Conductivity value from
CondP(AK95P.CPU_P.SUP.MEAS.AD_INPUT.condValue) <20 mS/cm

Some possible explanations why the error has occurred:

- Incorrect concentrate used (not possible to regulate conductivity >20mS/cm)
- Air leakage (pickup tube, tube, filter)
- Conductivity cell B is broken or uncalibrated
- Conductivity cell P is broken or uncalibrated
- Conductivity cell A is broken or uncalibrated
- A/D converter CPU P is uncalibrated

C COFF 088 026 CONDUCTIVITY TEST ERROR,

CONDUCTIVITY UNSTABLE (HIGH CONDUCTIVITY TEST)
Unconditional error, blood pump available

General description of conditions for occurring:

- The conductivity value measured in CPU P is not stable in the high
conductivity test

Technical description of conditions for occurring:

- PRI(PI_CondHighStableErrCnt) > 4

Some possible explanations why the error has occurred:

- Too much air in fluid system
- Conductivity cell B is broken or uncalibrated
- Conductivity cell P is broken or uncalibrated
- Conductivity cell A is broken or uncalibrated

C COFF 088 027 CONDUCTIVITY TEST ERROR,

CONDUCTIVITY COMPARE ERROR (LOW CONDUCTIVITY TEST)
Unconditional error, blood pump available

General description of conditions for occurring:

- The conductivity difference between CPU C and CPU P is too large in the
conductivity test low phase.

Technical description of conditions for occurring:

- PRI(PI_CondLowDiffErrCnt) > 4
- The difference between CondB(FRI(FI_MM90CONDB)) and
CondP(AK95P.CPU_P.SUP.MEAS.AD_INPUT.condValue) is outside limit
+/- 1mS/cm
- The difference between CondA (FRI(FI_MM90CONDA)) and CondP
(AK95P.CPU_P.SUP.MEAS.AD_INPUT.condValue) is outside limit +/-
1mS/cm
- The difference between CondA (FRI(FI_MM90CONDA)) and CondB
(FRI(FI_MM90CONDB))
(AK95P.CPU_P.SUP.MEAS.AD_INPUT.condValue) is outside limit +/-
0.3mS/cm

Some possible explanations why the error has occurred:

- Conductivity cell B is broken or uncalibrated
- Conductivity cell P is broken or uncalibrated

HCEN 9091 Page 53 of 106

- Conductivity cell A is broken or uncalibrated
- The A/D converters are uncalibrated (CPU P, MM 95)

C COFF 088 028 CONDUCTIVITY TEST ERROR,

CONDUCTIVITY VALUE TOO HIGH (LOW CONDUCTIVITY TEST)
Unconditional error, blood pump available

General description of conditions for occurring:

- The conductivity measured by CPU P is not low enough in the conductivity
test low phase.

Technical description of conditions for occurring:

- PRI(PI_CondLowLevelErrCnt) > 4
- Conductivity value from CondP
(AK95P.CPU_P.SUP.MEAS.AD_INPUT.condValue) was >5 mS/cm

Some possible explanations why the error has occurred:

- Conductivity cell B is broken or uncalibrated
- Conductivity cell P is broken or uncalibrated
- Conductivity cell A is broken or uncalibrated

C COFF 088 029 CONDUCTIVITY TEST ERROR,

CONDUCTIVITY UNSTABLE (LOW CONDUCTIVITY TEST)
Unconditional error, blood pump available

General description of conditions for occurring:

- The conductivity value measured in CPU P is not stable in the low
conductivity test

Technical description of conditions for occurring:

- PRI(PI_CondLowStableErrCnt) > 4

Some possible explanations why the error has occurred:

- Too much air in fluid system
- Conductivity cell B is broken or uncalibrated
- Conductivity cell P is broken or uncalibrated
- Conductivity cell A is broken or uncalibrated

C COFF 088 030 FLOW SWITCH ERROR, FLOW DETECTED (INVA CLOSED)
Unconditional error, blood pump available

General description of conditions for occurring:

- The flow switch senses fluid flow when INVA is closed.

Technical description of conditions for occurring:

- PRI(PI_FlowOffErrCnt) > 3
- PRL(P_FLOWSWITCHFLOW) = TRUE

Some possible explanations why the error has occurred:

- Flow switch broken
- Float stucked in upper position
- FM I/O board broken (IC2)
- Protective driver board broken (IC28)

C COFF 088 031 FLOW SWITCH ERROR, NO FLOW (INLET PRESSURE OK)
Unconditional error, blood pump available

General description of conditions for occurring:

- The flow switch does not sense flow when the inlet pressure (CPU C) is OK.

HCEN 9091 Page 54 of 106

Technical description of conditions for occurring:
- PRI(PI_FlowOn1ErrCnt) > 3
- PRL(P_FLOWSWITCHFLOW) = FALSE

Some possible explanations why the error has occurred:

- Flow switch broken
- Float stucked in lower position
- FM I/O board broken (IC2)
- Protective driver board broken (IC28)

C COFF 088 032 FLOW SWITCH ERROR, NO FLOW (INVA OPEN)

Unconditional error, blood pump available

General description of conditions for occurring:

- The flow switch does not sense flow when INVA is opened after the no flow
test.
- This error code is not used after P2.04

Technical description of conditions for occurring:

- PRI(PI_FlowOn2ErrCnt) > 3
- PRL(P_FLOWSWITCHFLOW) = FALSE

Some possible explanations why the error has occurred:

- Flow switch broken
- Float stucked in lower position
- FM I/O board broken (IC2)
- Protective driver board broken (IC28)

C COFF 088 033 COMMUNICATION ERROR BETWEEN CPU W AND P (FM1)

Unconditional error, blood pump available

General description of conditions for occurring:

- CPU W does not agree on that the fluid monitor function check part 1 is ready

Technical description of conditions for occurring:

- PRI(PI_Fm1ErrCnt) > 2

Some possible explanations why the error has occurred:

- Broken protective CPU board (IC26, V4 and components)

C COFF 088 034 COMMUNICATION ERROR BETWEEN CPU W AND P (FM2)

Unconditional error, blood pump available

General description of conditions for occurring:

CPU W does not agree on that the fluid monitor function check part 2 is ready

Technical description of conditions for occurring:

- PRI(PI_Fm2ErrCnt) > 2

Some possible explanations why the error has occurred:

- Broken protective CPU board (IC26, V4 and components)

C COFF 088 035 HEATER TEST ERROR, HEATER ENERGIZED (INVA CLOSED)
Unconditional error, blood pump available

General description of conditions for occurring:

- The heater is still energized after INVA has been closed. No flow in the
monitor.
- This error code is not used after P2.04

HCEN 9091 Page 55 of 106

Technical description of conditions for occurring:
- PRI(PI_HeaterOff1ErrCnt) > 3
- Signal PMAINS is high (+5V)

Some possible explanations why the error has occurred:

- P931 and P932 on heater relay board are incorrectly positioned
- The heater relay board is broken (IC1 and components)
- Protective driver board broken (IC25, IC 28)

C COFF 088 036 HEATER TEST ERROR, HEATER ENERGIZED (CPU P)

Unconditional error, blood pump available

General description of conditions for occurring:

- The heater is still energized when CPU P has turned the heater relay off.
- This error code is not used after P2.04

Technical description of conditions for occurring:

- PRI(PI_HeaterOff2ErrCnt) > 3
- Signal PMAINS is high (+5V)

Some possible explanations why the error has occurred:

- The heater relay board is broken (IC1 and components)
- Protective driver board broken (IC25, IC 28)

C COFF 088 037 HEATER TEST ERROR, HEATER NOT ENERGIZED (CPU C)
Unconditional error, blood pump available

General description of conditions for occurring:

- The heater is not energized when there is flow through to the monitor and
CPU C runs the heater with duty cycle 40 %.
- This error code is not used after P2.04

Technical description of conditions for occurring:

- PRI(PI_HeaterOn1ErrCnt) > 3
- Signal PMAINS is low (Zero volt)

Some possible explanations why the error has occurred:

- Broken fuse in AC/DC unit
- Control CPU board broken (IC21)
- Control driver board is broken (IC24)
- Float stucked in lower position
- Flow switch broken
- Flow switch in incorrect position (should be mounted close to lower silicon
connector)
- FM I/O board is broken (Q1, Q2, Q3, Q4, R2)
- Heater relay board is not connected
- Protective CPU board is broken (signal PHEEN)
- Protective driver board broken (IC25, IC 28)
- The heater relay board is broken (K1, K2, V1, IC1 and components)

C COFF 088 038 HEATER TEST ERROR, HEATER NOT ENERGIZED (INVA OPEN)
Unconditional error, blood pump available

General description of conditions for occurring:

- The heater is not energized when INVA is opened after the no flow test.
- This error code is not used after P2.04

Technical description of conditions for occurring:

- PRI(PI_HeaterOn2ErrCnt) > 3
- Signal PMAINS is low (Zero volt)

HCEN 9091 Page 56 of 106

Some possible explanations why the error has occurred:
- Broken fuse in AC/DC unit
- Control CPU board broken (IC21)
- Control driver board is broken (IC24)
- Float stucked in lower position
- Flow switch broken
- Flow switch in incorrect position (should be mounted close to lower silicon
connector)
- FM I/O board is broken (Q1, Q2, Q3, Q4, R2)
- Heater relay board is not connected
- Protective CPU board is broken (signal PHEEN)
- Protective driver board broken (IC25, IC 28)
- The heater relay board is broken (K1, K2, V1, IC1 and components)

C COFF 088 039 HEATER TEST ERROR, HEATER NOT ENERGIZED (CPU P)
Unconditional error, blood pump available

General description of conditions for occurring:

- The heater is not energized when CPU P has enabled the heater relay.
- This error code is not used after P2.04

Technical description of conditions for occurring:

- PRI(PI_HeaterOn3ErrCnt) > 3
- Signal PMAINS is low (Zero volt)

Some possible explanations why the error has occurred:

C COFB 088 040 HIGH VENOUS PRESSURE TEST ERROR, TOO HIGH VEN. PRESS.
Unconditional error, blood pump not available

General description of conditions for occurring:

- CPU C regulates a too high venous pressure during the high venous pressure
test.

Technical description of conditions for occurring:

- PRI(PI_HighVprPresErrCnt) > 1
- The venous pressure measured by CPU P
(AK95P.CPU_P.SUP.MEAS.AD_INPUT.vprValue) > 300mmHg

Some possible explanations why the error has occurred:

- The venous pressure transducer board is broken/uncalibrated (CPU C)
- The venous pressure transducer board is broken/uncalibrated (CPU P)

C COFB 088 041 HIGH VENOUS PRESSURE TEST ERROR, TOO BIG DIFFERENCE
Unconditional error, blood pump not available

General description of conditions for occurring:

HCEN 9091 Page 57 of 106

- The difference between the measurements from the venous pressure
transducers in CPU C and CPU P is to large.

Technical description of conditions for occurring:

- PRI(PI_HighVprTestErrCnt) > 3
- The venous pressure difference between CPU C (BRI(BI_VENPR)) and CPU
P (AK95P.CPU_P.SUP.MEAS.AD_INPUT.vprValue) >15mmHg

Some possible explanations why the error has occurred:

- The venous pressure transducer board is broken/uncalibrated (CPU C)
- The venous pressure transducer board is broken/uncalibrated (CPU P)
- There is a leakage of pressure in CPU C or/and CPU P venous pressure
transducer line.

C COFB 088 042 PRIMING DETECTOR TEST ERROR,

COMMUNICATION ERROR BETWEEN CPU P AND W
Unconditional error, blood pump not available

General description of conditions for occurring:

- In priming detector test, CPU W does not send the calibrated priming detector
transmitter current to CPU P.

Technical description of conditions for occurring:

- PRI(PI_PrimDetCalibCurrErrCnt) > 4

Some possible explanations why the error has occurred:

- The protective CPU board is broken

C COFB 088 043 PRIMING DETECTOR TEST ERROR, CURRENT OUT OF LIMIT
Unconditional error, blood pump not available

General description of conditions for occurring:

- The difference between the stored and the measured priming detector current
was too big.

Technical description of conditions for occurring:

- PRI(PI_PrimDetCurrErrCnt) > 4

Some possible explanations why the error has occurred:

- Priming detector is uncalibrated
- Priming detector board is broken
- CPU W is uncalibrated
- Priming detector transmitter electronics broken (IC55, IC33, Q9, Q13 and
components) on protective driver board.
- Protective CPU board is broken (R29, C21)

C COFB 088 044 PRIMING DETECTOR TEST ERROR,

BLOOD IN PRIMING DETECTOR (FIRST TEST), CPU P
Unconditional error, blood pump not available

General description of conditions for occurring:

CPU P sensed “blood” when the priming detector test is started and the
transmitter intensity is high.

Technical description of conditions for occurring:

- PRI(PI_PrimDetEmptyP1ErrCnt) > 10

Some possible explanations why the error has occurred:

- Priming detector not connected to FM I/O board (P504)
- Priming detector is not empty or priming detector dirty

HCEN 9091 Page 58 of 106

- Priming detector board is broken
- Priming detector transmitter electronics broken (IC55, IC33, Q9, Q13 and
components) on protective driver board.
- Priming detector receiver electronics broken (IC18, V11, V12 and
components) on protective driver board.

C COFB 088 045 PRIMING DETECTOR TEST ERROR,

BLOOD IN PRIMING DETECTOR (FIRST TEST), CPU W
Unconditional error, blood pump not available

General description of conditions for occurring:

- CPU W sensed “blood” when the priming detector test is started and the
transmitter intensity is high.

Technical description of conditions for occurring:

- PRI(PI_PrimDetEmptyW1ErrCnt) > 10

Some possible explanations why the error has occurred:

- Priming detector not connected to FM I/O board (P504)
- Priming detector is not empty or priming detector dirty
- Priming detector board is broken
- Priming detector transmitter electronics broken (IC55, IC33, Q9 and
components) on protective driver board.
- Priming detector receiver electronics broken (IC11, V9, V10 and
components) on protective driver board.

C COFB 088 046 PRIMING DETECTOR TEST ERROR, NO BLOOD DETECTED (CPU P)
Unconditional error, blood pump not available

General description of conditions for occurring:

- CPU P does not sense “blood” when the priming detector intensity is lowered.

Technical description of conditions for occurring:

- PRI(PI_PrimDetBloodPErrCnt) > 10

Some possible explanations why the error has occurred:

C COFB 088 047 PRIMING DETECTOR TEST ERROR, NO BLOOD DETECTED (CPU W)
Unconditional error, blood pump not available

General description of conditions for occurring:

- CPU W does not sense “blood” when the priming detector intensity is
lowered.

Technical description of conditions for occurring:

- PRI(PI_PrimDetBloodWErrCnt) > 10

Some possible explanations why the error has occurred:

- Priming detector transmitter electronics broken (IC55, IC33, Q9 and
components) on protective driver board.
- Priming detector receiver electronics broken (IC11, V9, V10 and
components) on protective driver board.
- CPU W is uncalibrated/broken (IC10 on protective CPU board)

C COFB 088 048 PRIMING DETECTOR TEST ERROR,

HCEN 9091 Page 59 of 106

BLOOD IN PRIMING DETECTOR (SECOND TEST), CPU P
Unconditional error, blood pump not available

General description of conditions for occurring:

- CPU P sensed “blood” when the priming detector test intensity is high again
after the low intensity test..

Technical description of conditions for occurring:

- PRI(PI_PrimDetEmptyP2ErrCnt) > 10

Some possible explanations why the error has occurred:

- Priming detector not connected to FM I/O board (P504)
- Software error
- Priming detector is not empty or priming detector dirty
- Priming detector board is broken
- Priming detector transmitter electronics broken (IC55, IC33, Q9, Q13 and
components) on protective driver board.
- Priming detector receiver electronics broken (IC18, V11, V12 and
components) on protective driver board.

C COFB 088 049 PRIMING DETECTOR TEST ERROR,

BLOOD IN PRIMING DETECTOR (SECOND TEST), CPU W
Unconditional error, blood pump not available

General description of conditions for occurring:

CPU W sensed “blood” when the priming detector test intensity is high again
after the low intensity test.

Technical description of conditions for occurring:

- PRI(PI_PrimDetEmptyW2ErrCnt) > 10

Some possible explanations why the error has occurred:

C COFB 088 050 SAFETY RELAY TEST ERROR, REFERENCE CURRENT TOO HIGH
Unconditional error, blood pump not available

General description of conditions for occurring:

- At the beginning of the relay test the current is measured when the relay is
OFF (this current value is used as reference current in the following tests). The
reference current measured was too high.

Technical description of conditions for occurring:

- PRI(PI_RelayOff1ErrCnt) > 4

Some possible explanations why the error has occurred:

- The safety relay (K2) on control CPU board is broken
- The valve current measuring system is broken (R20 and components) on
protective driver board.
- CPU P is uncalibrated

C COFB 088 051 SAFETY RELAY TEST ERROR,

TOO HIGH CURRENT DIFFERENCE (FIRST TEST)

HCEN 9091 Page 60 of 106

Unconditional error, blood pump not available

General description of conditions for occurring:

- The difference between the reference current and the second current value,
measured when the relay is OFF, is too high (the safety relay is OFF and
BYVA is open).

Technical description of conditions for occurring:

- PRI(PI_RelayOff2ErrCnt) > 4

Some possible explanations why the error has occurred:

- The safety relay (K2) on control CPU board is broken
- The valve current measuring system is broken (R20 and components) on
protective driver board.
- CPU P is uncalibrated

C COFB 088 052 SAFETY RELAY TEST ERROR,

TOO LOW CURRENT DIFFERENCE (FIRST TEST)
Unconditional error, blood pump not available

General description of conditions for occurring:

- The difference between the reference current and the first current value,
measured when the relay is ON, is too small (safety relay is ON and BYVA is
open).

Technical description of conditions for occurring:

- PRI(PI_RelayOn1ErrCnt) > 4

Some possible explanations why the error has occurred:

- BYVA is not connected (or broken).
- Protective driver board is broken (IC3, Q3)
- The safety relay (K2) on control CPU board is broken
- The valve current measuring system is broken (R20 and components) on
protective driver board.
- CPU P is uncalibrated

C COFB 088 053 SAFETY RELAY TEST ERROR,

TOO LOW CURRENT DIFFERENCE (SECOND TEST)
Unconditional error, blood pump not available

General description of conditions for occurring:

- The difference between the reference current and the second current value,
measured when the relay is ON, is too small (safety relay is ON and BYVA is
open).

Technical description of conditions for occurring:

- PRI(PI_RelayOn2ErrCnt) > 4

Some possible explanations why the error has occurred:

C COFB 088 054 SAFETY RELAY TEST ERROR,

TOO HIGH CURRENT DIFFERENCE (SECOND TEST)
Unconditional error, blood pump not available

HCEN 9091 Page 61 of 106

General description of conditions for occurring:
- The difference between the reference current and the third current value,
measured when the relay is ON, is too high (safety relay is ON and BYVA is
closed.

Technical description of conditions for occurring:

- PRI(PI_RelayOn3ErrCnt) > 4

Some possible explanations why the error has occurred:

- Protective driver board is broken (IC3, Q3) (BYVA does not close)
- The valve current measuring system is broken (R20 and components) on
protective driver board.
- CPU P is uncalibrated

C COFF 088 055 TEMPERATURE TEST ERROR,

TOO HIGH TEMPERATURE DIFFERENCE (HIGH TEMP. TEST)
Unconditional error, blood pump available

General description of conditions for occurring:

- The temperature difference between CPU C and CPU P is too large in the
temperature test high phase. TempC is measured in conductivity cell B.

Technical description of conditions for occurring:

- PRI(PI_TempHighDiffErrCnt) > 10
- TempC-TempP >1.3ºC or TempC-TempP <-0.6ºC

Some possible explanations why the error has occurred:

- CPU C A/D-system uncalibrated
- CPU P A/D-system uncalibrated
- Conductivity cell B broken
- Conductivity cell P broken

C COFF 088 056 TEMPERATURE TEST ERROR,

TOO LOW TEMPERATURE MEASURED (HIGH TEMP. TEST)
Unconditional error, blood pump available

General description of conditions for occurring:

- The measured temperature (tempP) is lower than the test limit in the high
temperature test. The temperature measured by tempP was below 41ºC even
though the temperature had been increased a second time by CPU C.

Technical description of conditions for occurring:

- PRI(PI_TempHighLevelErrCnt) > 4
- tempP < 41ºC

Some possible explanations why the error has occurred:

- The temperature regulation system is broken (control CPU board)
- CPU C A/D-system uncalibrated
- CPU P A/D-system uncalibrated
- Conductivity cell B broken
- Conductivity cell P broken

C COFF 088 057 TEMPERATURE TEST ERROR,

UNSTABLE TEMPERATURE (HIGH TEMP. TEST)
Unconditional error, blood pump available

General description of conditions for occurring:

- The measured temperature value is not stable in the high temperature test .

Technical description of conditions for occurring:

HCEN 9091 Page 62 of 106

- PRI(PI_TempHighStableErrCnt) > 4

Some possible explanations why the error has occurred:

- The temperature regulation system is broken (control CPU board)
- CPU P A/D-system uncalibrated
- Conductivity cell P broken

C COFF 088 058 TEMPERATURE TEST ERROR,

TOO HIGH TEMPERATURE DIFFERENCE (LOW TEMP. TEST)
Unconditional error, blood pump available

General description of conditions for occurring:

The temperature difference between CPU C and CPU P is too large in the
temperature test low phase. TempC is measured in conductivity cell B.

Technical description of conditions for occurring:

- PRI(PI_TempLowDiffErrCnt) > 4
- TempC-TempP >1.2ºC or TempC-TempP <-0.6ºC

Some possible explanations why the error has occurred:

- CPU C A/D-system uncalibrated
- CPU P A/D-system uncalibrated
- Conductivity cell B broken
- Conductivity cell P broken

C COFF 088 059 TEMPERATURE TEST ERROR,

UNSTABLE TEMPERATURE (LOW TEMP. TEST)
Unconditional error, blood pump available

General description of conditions for occurring:

- The measured temperature value is not stable in the low temperature test.

Technical description of conditions for occurring:

- PRI(PI_TempLowStableErrCnt) > 4

Some possible explanations why the error has occurred:

- The temperature regulation system is broken (control CPU board)
- CPU P A/D-system uncalibrated
- Conductivity cell P broken

C COFF 088 060 DIVA/TAVA TEST ERROR,

FAILURE TO ACHIEVE HIGH LEVEL IN DEAIRATING CHAMBER
Unconditional error, blood pump available

General description of conditions for occurring:

- High level in the deairating chamber is not achieved at the start of valve
leakage (DIVA/TAVA) test.

Technical description of conditions for occurring:

- PRI(PI_ValveFillupErrCnt) > 4

Some possible explanations why the error has occurred:

- Bad/no connection to level switch in deairating chamber. Check connection
from level switch to FM I/O board (P503).
- Level switch broken
- EVVA is not open
- TAVA is not closed
- IC 28 on protective driver board broken
- FIVA is malfunctioning (if the UFD-kit is installed)

HCEN 9091 Page 63 of 106

C COFF 088 061 DIVA/TAVA TEST ERROR, LEAKAGE IN HIGH PRESSURE TEST
Unconditional error, blood pump available

General description of conditions for occurring:

- The dialysis pressure was measured twice with DIVA/TAVA/EVVA closed.
The difference between the two pressure measurements was too big.

Technical description of conditions for occurring:

- PRI(PI_ValveHighLeakErrCnt) > 4
- The dialysis pressure changed more than +/-30mmHg between the two
measurements.

Some possible explanations why the error has occurred:

- There is a leakage between the dialyzer connector and the bypass nipple.
Check the oring in the dialyzer connector.
- The deairating chamber is leaking
- DIVA/TAVA/EVVA/REVA is leaking
- There is a leakage in the flow meter on the front of the machine
- FIVA is leaking (if the UFD-kit is installed)

C COFF 088 062 DIVA/TAVA TEST ERROR, DIALYSIS PRESSURE OUTSIDE LIMITS
IN THE LOW PRESSURE TEST (SECOND TEST)
Unconditional error, blood pump available

General description of conditions for occurring:

- CPU C had regulated a dialysis fluid pressure at +200mmHg, measured at
HPG. The dialysis fluid pressure, measured at the dialysis pressure transducer,
was outside 200+/-20 mmHg.

Technical description of conditions for occurring:

- PRI(PI_ValveHighLevel1ErrCnt) > 4
- Dialysis fluid pressure outside 200+/-20 mmHg

Some possible explanations why the error has occurred:

- DIVA does not open
- The HPG transducer or the dialysis pressure transducer is uncalibrated.

C COFF 088 063 DIVA/TAVA TEST ERROR, DIALYSIS PRESSURE OUTSIDE LIMITS
IN THE HIGH PRESSURE TEST (FIRST TEST)
Unconditional error, blood pump available

General description of conditions for occurring:

- CPU C had regulated a dialysis fluid pressure at +200mmHg, measured at
HPG. The dialysis fluid pressure, measured at the dialysis pressure transducer,
was outside 200+/-20 mmHg.

Technical description of conditions for occurring:

- PRI(PI_ValveHighLevel2ErrCnt) > 4
- Dialysis fluid pressure outside 200+/-20 mmHg

Some possible explanations why the error has occurred:

- The HPG transducer or the dialysis pressure transducer is uncalibrated.
- Unstable dialysis flow

C COFF 088 064 DIVA/TAVA TEST ERROR,

UNSTABLE PRESSURE IN HIGH PRESSURE TEST
Unconditional error, blood pump available

General description of conditions for occurring:

- The dialysis pressure is not stable in the high pressure test. Regulated

HCEN 9091 Page 64 of 106

pressure approx. +200mmHg (HPG)

Technical description of conditions for occurring:

- PRI(PI_ValveHighStableErrCnt) > 4
- The dialysis fluid pressure variance was >20

Some possible explanations why the error has occurred:

- There is too much air in the dialysis fluid
- The HPG pressure transducer is broken
- The dialysis fluid pressure transducer is broken

C COFF 088 065 DIVA/TAVA TEST ERROR, LEAKAGE IN LOW PRESSURE TEST
Unconditional error, blood pump available

General description of conditions for occurring:

- The dialysis pressure was measured twice with DIVA/TAVA/EVVA closed.
The difference between the two pressure measurements was too big.

Technical description of conditions for occurring:

- PRI(PI_ValveLowLeakErrCnt) > 4
- The dialysis pressure changed more than +/-20mmHg between the two
measurements.

Some possible explanations why the error has occurred:

C COFF 088 066 DIVA/TAVA TEST ERROR, DIALYSIS PRESSURE OUTSIDE LIMITS
IN LOW PRESSURE TEST (FIRST TEST)
Unconditional error, blood pump available

General description of conditions for occurring:

- CPU C had regulated a dialysis fluid pressure at -200mmHg, measured at
HPG. The dialysis fluid pressure, measured at the dialysis pressure transducer,
was outside -200+/-20 mmHg.

Technical description of conditions for occurring:

- PRI(PI_ValveLowLevel1ErrCnt) > 4
- Dialysis fluid pressure outside -200+/-20 mmHg

Some possible explanations why the error has occurred:

- The HPG transducer or the dialysis pressure transducer is uncalibrated.

C COFF 088 067 DIVA/TAVA TEST ERROR, DIALYSIS PRESSURE OUTSIDE LIMITS
IN HIGH PRESSURE TEST (SECOND TEST)
Unconditional error, blood pump available

General description of conditions for occurring:

- CPU C had regulated a dialysis fluid pressure at -200mmHg, measured at
HPG. The dialysis fluid pressure, measured at the dialysis pressure transducer,
was outside -200+/-20 mmHg.

Technical description of conditions for occurring:

- PRI(PI_ValveLowLevel2ErrCnt) > 4
- Dialysis fluid pressure outside -200+/-20 mmHg

HCEN 9091 Page 65 of 106

Some possible explanations why the error has occurred:
- TAVA does not open
- The HPG transducer or the dialysis pressure transducer is uncalibrated.

C COFF 088 068 DIVA/TAVA TEST ERROR, UNSTABLE PRESSURE

IN THE LOW PRESSURE TEST
Unconditional error, blood pump available

General description of conditions for occurring:

- The dialysis pressure is not stable in the low pressure test. Regulated pressure
approx. -200mmHg (HPG)

Technical description of conditions for occurring:

- PRI(PI_ValveLowStableErrCnt) > 4
- The dialysis fluid pressure variance was >20

Some possible explanations why the error has occurred:

- There is too much air in the dialysis fluid
- The HPG pressure transducer is broken
- The dialysis fluid pressure transducer is broken

C COFB 088 069 VENOUS CLAMP TEST ERROR, CLAMP NOT OPEN AT START
Unconditional error, blood pump not available

General description of conditions for occurring:

- The venous clamp is closed when the clamp test starts (the clamp is
commanded open).

Technical description of conditions for occurring:

- PRI(PI_VClampOpen1ErrCnt) > 4
- BRL(B_VenClampClosed)=TRUE

Some possible explanations why the error has occurred:

- The venous clamp is stucked in closed position
- The clamp driver board is broken (transmitter-receiver)
- Protective CPU board broken (R47, IC45, IC20, Q7, Q8, IC46, IC41, IC7)
- Control CPU board broken (IC24)

C COFB 088 070 VENOUS CLAMP TEST ERROR, CLAMP NOT OPEN (CPU P)
Unconditional error, blood pump not available

General description of conditions for occurring:

The venous clamp does not open after it was closed by CPU P

Technical description of conditions for occurring:

- PRI(PI_VClampOpen2ErrCnt) > 4
- BRL(B_VenClampClosed)=TRUE

Some possible explanations why the error has occurred:

C COFB 088 071 VENOUS CLAMP TEST ERROR, CLAMP NOT OPEN (CPU W)
Unconditional error, blood pump not available

General description of conditions for occurring:

- The venous clamp does not open after it was closed by CPU W

HCEN 9091 Page 66 of 106

Technical description of conditions for occurring:
- PRI(PI_VClampOpen3ErrCnt) > 4
- BRL(B_VenClampClosed)=TRUE

Some possible explanations why the error has occurred:

C COFB 088 072 VENOUS CLAMP TEST ERROR, CLAMP NOT CLOSED (CPU P)
Unconditional error, blood pump not available

General description of conditions for occurring:

- CPU P can not close the venous clamp.

Technical description of conditions for occurring:

- PRI(PI_VClampPCloseErrCnt) > 10
- BRL(B_VenClampClosed)=FALSE

Some possible explanations why the error has occurred:

- The venous clamp is stucked in open position
- The clamp driver board is broken (transmitter-receiver)
- Protective CPU board broken (R47, IC45, IC20, Q8, IC41)

C COFB 088 073 VENOUS CLAMP TEST ERROR, CLAMP NOT CLOSED (CPU W)
Unconditional error, blood pump not available

General description of conditions for occurring:

- CPU W can not close the venous clamp.

Technical description of conditions for occurring:

- PRI(PI_VClampWCloseErrCnt) > 10
- BRL(B_VenClampClosed)=FALSE

Some possible explanations why the error has occurred:

- The venous clamp is stucked in open position
- The clamp driver board is broken (transmitter-receiver)
- Protective CPU board broken (R47, IC45, IC20, Q7, IC46, IC7)

C COFB 088 074 ARTERIAL CLAMP TEST ERROR

Unconditional error, blood pump not available

General description of conditions for occurring:

The arterial clamp test failed, either when opening or when closing the clamp

Technical description of conditions for occurring:

- BRL(B_ArtClampTestErr)= TRUE

Some possible explanations why the error has occurred:

- The clamp is mechanically jammed or blocked
- Bad connection between clamp unit and the cabling
- The clamp unit is broken
- Protective CPU board broken (IC45, Q6, V7)
- Control CPU board broken (IC24)

C COFF 088 075 HEATER TEST ERROR, HEATER ENERGIZED

Unconditional error, blood pump not available

HCEN 9091 Page 67 of 106

General description of conditions for occurring:
- The heater is still energized after CPU C has regulated 0% dutycycle

Technical description of conditions for occurring:

- PRI(PI_HeaterOff1ErrCnt) > 3
- Signal PMAINS is high (+5V)

Some possible explanations why the error has occurred:

- P931 and P932 on heater relay board are incorrectly positioned
- The heater relay board is broken (K1)
- The heater relay board is broken (IC1and components)
- Protective driver board broken (IC25, IC 28)
- Control CPU board is broken (IC21)

C COFF 088 076 HEATER TEST ERROR, HEATER ENERGIZED

Unconditional error, blood pump available

General description of conditions for occurring:

- The heater is still energized when CPU P has turned the heater relay off.

Technical description of conditions for occurring:

- PRI(PI_HeaterOff2ErrCnt) > 3
- Signal PMAINS is high (+5V)

Some possible explanations why the error has occurred:

- The FM I/O board is broken (Q1, R8)
- The heater relay board is broken (IC1 and components)
- Protective driver board broken (IC3, IC25, IC 28)

C COFF 088 077 HEATER TEST ERROR, HEATER ENERGIZED

Unconditional error, blood pump available

General description of conditions for occurring:

- The heater is still energized after CPU C has shut off the heater relay.

Technical description of conditions for occurring:

- PRI(PI_HeaterOff3ErrCnt) > 3
- Signal PMAINS is high (+5V)

Some possible explanations why the error has occurred:

- The FM I/O board is broken (Q2)
- The control driver board is broken (IC24)
- The heater relay board is broken (IC1 and components)
- The protective driver board is broken (IC25, IC 28)

C COFF 088 078 HEATER TEST ERROR, HEATER ENERGIZED

Unconditional error, blood pump available

General description of conditions for occurring:

- The heater is still energized after INVA has been closed. No flow through the
flow switch.

Technical description of conditions for occurring:

- PRI(PI_HeaterOff4ErrCnt) > 3
- Signal PMAINS is high (+5V)

Some possible explanations why the error has occurred:

- The flow switch is stucked in upper position
- The FM I/O board is broken (Q4)
- The heater relay board is broken (IC1 and components)

HCEN 9091 Page 68 of 106

- Protective driver board broken (IC25, IC 28)

C COFF 088 079 HEATER TEST ERROR, HEATER NOT ENERGIZED

Unconditional error, blood pump available

General description of conditions for occurring:

- The heater is not energized when there is flow through to the monitor and
CPU C runs the heater with duty cycle 40 %.

Technical description of conditions for occurring:

- PRI(PI_HeaterOn1ErrCnt) > 3
- Signal PMAINS is low (Zero volt)

Some possible explanations why the error has occurred:

- Broken fuse in AC/DC unit
- Control CPU board broken (IC21)
- Control driver board is broken (IC24)
- Float stucked in lower position
- Flow switch broken
- FM I/O board is broken (Q1, Q2, Q3, Q4, R2)
- Heater relay board is not connected
- Protective CPU board is broken (signal PHEEN)
- Protective driver board broken (IC25, IC 28)
- The heater relay board is broken (K1, K2, V1, IC1 and components)

C COFF 088 080 HEATER TEST ERROR, HEATER NOT ENERGIZED

Unconditional error, blood pump available

General description of conditions for occurring:

- The heater is not energized when there is flow through to the monitor and
CPU C runs the heater with duty cycle 40 %.

Technical description of conditions for occurring:

- PRI(PI_HeaterOn2ErrCnt) > 3
- Signal PMAINS is low (Zero volt)

Some possible explanations why the error has occurred:

C COFF 088 081 HEATER TEST ERROR, HEATER NOT ENERGIZED

Unconditional error, blood pump available

General description of conditions for occurring:

- The heater is not energized when there is flow through to the monitor and
CPU C runs the heater with duty cycle 40 %.

Technical description of conditions for occurring:

- PRI(PI_HeaterOn3ErrCnt) > 3
- Signal PMAINS is low (Zero volt)

Some possible explanations why the error has occurred:

HCEN 9091 Page 69 of 106

C COFF 088 082 HEATER TEST ERROR, HEATER NOT ENERGIZED

Unconditional error, blood pump available

General description of conditions for occurring:

- The heater is not energized when there is flow through to the monitor and
CPU C runs the heater with duty cycle 40 %.

Technical description of conditions for occurring:

- PRI(PI_HeaterOn4ErrCnt) > 3
- Signal PMAINS is low (Zero volt)

Some possible explanations why the error has occurred:

C COFF 088 083 HEATER TEST ERROR, HEATER NOT ENERGIZED

Unconditional error, blood pump available

General description of conditions for occurring:

- The heater is not energized when there is flow through to the monitor and
CPU C runs the heater with duty cycle 40 %.

Technical description of conditions for occurring:

- PRI(PI_HeaterOn5ErrCnt) > 3
- Signal PMAINS is low (Zero volt)

Some possible explanations why the error has occurred:

HCEN 9091 Page 70 of 106

- Protective driver board broken (IC25, IC 28)
- The heater relay board is broken (K1, K2, V1, IC1 and components)

C COFF 088 084 FAILURE WHEN REGULATING HPG PRESSURE (DIVA/TAVA test)
Unconditional error, blood pump available

General description of conditions for occurring:

- No “pressure achieved” acknowledge signal sent to CPU P from CPU C
- This error code is not used in program version 3.00 and later

Technical description of conditions for occurring:

- PRI(PI_ValveNoAchErrCnt) > 4

Some possible explanations why the error has occurred:

- Leakage between the dialysis fluid tubes and the machine
- Leakage between the dialyzer connectors and the bypass unit
- Broken HPG transducer
- Broken control driver board (Q12 and components)
- Broken control CPU board (IC32)

C COFF 088 085 NO CONDUCTIVITY VALUE SENT TO CPU P (LOW TEST)

Unconditional error, blood pump available

General description of conditions for occurring:

- No conductivity value sent from CPU C to CPU P during conductivity test

Technical description of conditions for occurring:

- PRI(PI_CondNoAchLowErrCnt) > 0
- The low test has been running for 60 seconds with no value sent from CPU C

Some possible explanations why the error has occurred:

- Air in fluid path
- Broken CPU C conductivity cell (cell B)
- Broken MM I/O board
- Broken control driver board
- Broken protective CPU board (IC50)
- Broken control CPU board (IC5, IC4, IC1 and components)

C COFF 088 086 UNSTABLE LEVEL IN DEAIRATING CHAMBER

Unconditional error, blood pump available

General description of conditions for occurring:

- The level in deairating chamber is unstable.
- The level should have been high

Technical description of conditions for occurring:

- PRI(PI_ValveBubLevelErrCnt) > 10 (UFD-kit not installed)
- PRI(PI_ValveBubLevelErrCnt) > 65 ( UFD-kit installed)
- AK95P.CPU_P.SUP.MEAS.MEASURE_INPUT.bubble (log. variable)

Some possible explanations why the error has occurred:

- Air leakage
- Broken level detector
- EVVA is not open or malfunctioning
- TAVA is not closed or malfunctioning
- IC 28 on protective driver board broken
- FIVA is broken (if the UFD-kit is preseted)
- UFD is not preseted, despite the ultrafilter and FIVA is mounted

C COFF 088 087 FAILURE WHEN REGULATING HPG PRESSURE (DIVA/TAVA test)

HCEN 9091 Page 71 of 106

Unconditional error, blood pump available

General description of conditions for occurring:

- No “pressure achieved” acknowledge signal sent to CPU P from CPU C
- CPU is regulating HPG pressure to -200mmHg

Technical description of conditions for occurring:

- PRI(PI_ValveNoAchLow1ErrCnt) > 4

Some possible explanations why the error has occurred:

- Air in fluid. Check for leakage
- Leakage between the dialysis fluid tubes and the machine
- Leakage between the dialyzer connectors and the bypass unit
- Broken HPG transducer
- Broken control driver board (Q12 and components)
- Broken control CPU board (IC32)

C COFF 088 088 FAILURE WHEN REGULATING HPG PRESSURE (DIVA/TAVA test)
Unconditional error, blood pump available

General description of conditions for occurring:

- No “pressure achieved” acknowledge signal sent to CPU P from CPU C
- CPU is regulating HPG pressure to +200mmHg

Technical description of conditions for occurring:

- PRI(PI_ValveNoAchHigh1ErrCnt) > 2

Some possible explanations why the error has occurred:

C COFF 088 089 FAILURE WHEN REGULATING HPG PRESSURE (DIVA/TAVA test)
Unconditional error, blood pump available

General description of conditions for occurring:

- No “pressure achieved” acknowledge signal sent to CPU P from CPU C
- CPU is regulating HPG pressure to -200mmHg

Technical description of conditions for occurring:

- PRI(PI_ValveNoAchLow2ErrCnt) > 2

Some possible explanations why the error has occurred:

C COFF 088 090 FAILURE WHEN REGULATING HPG PRESSURE (DIVA/TAVA test)
Unconditional error, blood pump available

General description of conditions for occurring:

- No “pressure achieved” acknowledge signal sent to CPU P from CPU C
- CPU is regulating HPG pressure to +200mmHg

HCEN 9091 Page 72 of 106

Technical description of conditions for occurring:
- PRI(PI_ValveNoAchHigh2ErrCnt) > 2

Some possible explanations why the error has occurred:

C COFF 088 091 TOO HIGH TEMPERATURE AT START-UP

Unconditional error, blood pump available

General description of conditions for occurring:

- CPU P could not measure a temp below 45C (15 minute measure time)

Technical description of conditions for occurring:

- PRI(PI_TempStartHiErrCnt) > 0
- AK95P.CPU_P.SUP.MEAS.AD_INPUT.tempValue > 45C

Some possible explanations why the error has occurred:

- Broken CPU P temperature transducer
- Broken MM 95 board
- Broken protective driver board

C COFF 088 092 FAILURE WHEN REGULATING TEMPERATURE (high temp. test)

General description of conditions for occurring:

- CPU C has not been able to regulate the temperature

Technical description of conditions for occurring:

- PRI(PI_TempNoAchHigh1ErrCnt) > 0
- Unstable temperature in conductivity cell B, (FRI(FI_MM90CondTempB)

Some possible explanations why the error has occurred:

- Air in fluid path
- Unstable fluid flow or unstable fluid pressure (check PR2)
- Broken heater relay unit

C COFF 088 093 FAILURE WHEN REGULATING TEMPERATURE (high temp. test)

General description of conditions for occurring:

- CPU C has not been able to regulate the temperature (during retest)

Technical description of conditions for occurring:

- PRI(PI_TempNoAchHigh2ErrCnt) > 0
- Unstable temperature in conductivity cell B, (FRI(FI_MM90CondTempB)

Some possible explanations why the error has occurred:

- Air in fluid path
- Unstable fluid flow or unstable fluid pressure (check PR2)
- Broken heater relay unit

C COFF 088 094 FAILURE WHEN REGULATING TEMPERATURE (low temp. test)

General description of conditions for occurring:

- CPU C has not been able to regulate the temperature

Technical description of conditions for occurring:

HCEN 9091 Page 73 of 106

- PRI(PI_TempNoAchLowErrCnt) > 0
- Unstable temperature in conductivity cell B, FRI(FI_MM90CondTempB)

Some possible explanations why the error has occurred:

- Air in fluid path
- Unstable fluid flow or unstable fluid pressure (check PR2)
- Broken heater relay unit

C COFF 088 095 UNSTABLE CONDUCTIVITY (HIGH TEST)

Unconditional error, blood pump available

General description of conditions for occurring:

- No conductivity value sent from CPU C to CPU P due to unstable signal

Technical description of conditions for occurring:

- PRI(PI_CondNoAchHighErrCnt) > 0
- Unstable cond. value in conductivity cell B, FRI(FI_MM90CONDB)

Some possible explanations why the error has occurred:

- Air in fluid path
- Broken CPU C conductivity cell (cell B)
- Broken MM I/O board
- Broken control driver board

C COFB 088 096 BATTERY TEST ERROR 4 TIMES IN SUCCESSION

Unconditional error, blood pump not available

General description of conditions for occurring:

- Protective system has measured too low battery
voltage at least 4 times in succession

Technical description of conditions for occurring:

- Measured voltage < 7.5 V (no load on the battery)
- Measured voltage < 6.0 V (battery loaded with 50 mA)

Some possible explanations why the error has occurred:

- The 9 V battery is missing or discharged

REMOVED FROM PROGRAM VERSION 11.00

C COFF 088 097 COMMUNICATION FAILURE DURING VALVES CURRENT TEST

Unconditional error, blood pump not available

General description of conditions for occurring:

- CPU P has sent a request to CPU C to set the status of BYVA and DIVA in a
specified way. CPU P has not got any confirmation of the request.

Technical description of conditions for occurring:

- PRI(PI_CurrVaConfirmErrCnt) > 5
- CPU P didn’t receive any confirm signal.

Some possible explanations why the error has occurred:

- Broken CPU C board
- Broken CPU P board

C COFF 088 098 CLOSE FAILURE DURING VALVES CURRENT TEST

Unconditional error, blood pump not available

General description of conditions for occurring:

- The valves DIVA, BYVA, TAVA and EVVA should be closed but the

HCEN 9091 Page 74 of 106

measured valve current indicates that at least one of them is open.

Technical description of conditions for occurring:

- PRI(PI_CurrVaCloseErrCnt) > 2
- The valve current indicates that some valve is open.

Some possible explanations why the error has occurred:

- Broken Control driver board
- Broken Protective driver board

C COFF 088 099 DIVA OPEN FAILURE DURING VALVES CURRENT TEST
Unconditional error, blood pump not available

General description of conditions for occurring:

- DIVA should be open but the measured valve current indicates that it is
closed.

Technical description of conditions for occurring:

- PRI(PI_CurrVaOpenDIVACPErrCnt) > 2
- The valve current indicates that DIVA is closed.

Some possible explanations why the error has occurred:

- Broken DIVA
- Broken Control driver board
- Broken Protective driver board

C COFF 088 100 DIVA P CLOSED FAILURE DURING VALVES CURRENT TEST
Unconditional error, blood pump not available

General description of conditions for occurring:

- DIVA should be closed but the measured valve current indicates that it is
open. CPU C wants to have DIVA open. CPU P wants to have DIVA
closed.

Technical description of conditions for occurring:

PRI(PI_CurrVaOpenDIVACErrCnt) > 2
The valve current indicates that DIVA is open.

Some possible explanations why the error has occurred:

Broken Control driver board
Broken Protective driver board

C COFF 088 101 DIVA C CLOSED FAILURE DURING VALVES CURRENT TEST
Unconditional error, blood pump not available

General description of conditions for occurring:

- DIVA should be closed but the measured valve current indicates that it is
open. CPU C wants to have DIVA closed. CPU P wants to have DIVA
open.

Technical description of conditions for occurring:

- PRI(PI_CurrVaOpenDIVAPErrCnt) > 2
- The valve current indicates that DIVA is open.

Some possible explanations why the error has occurred:

- Broken Control driver board
- Broken Protective driver board

C COFF 088 102 BYVA OPEN FAILURE DURING VALVES CURRENT TEST
Unconditional error, blood pump not available

HCEN 9091 Page 75 of 106

General description of conditions for occurring:
- BYVA should be open but the measured valve current indicates that it is
closed.

Technical description of conditions for occurring:

- PRI(PI_CurrVaOpenBYVACPErrCnt) > 2
- The valve current indicates that BYVA is closed.

Some possible explanations why the error has occurred:

- Broken BYVA
- Broken Control driver board
- Broken Protective driver board

C COFF 088 103 BYVA C OPEN FAILURE DURING VALVES CURRENT TEST
Unconditional error, blood pump not available

General description of conditions for occurring:

- BYVA should be open but the measured valve current indicates that it is
closed. CPU C wants to have BYVA open. CPU P wants to have BYVA
closed.

Technical description of conditions for occurring:

- PRI(PI_CurrVaOpenBYVACErrCnt) > 2
- The valve current indicates that BYVA is closed.

Some possible explanations why the error has occurred:

- Broken BYVA
- Broken Control driver board
- Broken Protective driver board

C COFF 088 104 BYVA P OPEN FAILURE DURING VALVES CURRENT TEST
Unconditional error, blood pump not available

General description of conditions for occurring:

- BYVA should be open but the measured valve current indicates that it is
closed. CPU C wants to have BYVA closed. CPU P wants to have BYVA
open.

Technical description of conditions for occurring:

- PRI(PI_CurrVaOpenBYVAPErrCnt) > 2
- The valve current indicates that BYVA is closed.

Some possible explanations why the error has occurred:

- Broken BYVA
- Broken Control driver board
- Broken Protective driver board

C COFF 088 105 TAVA OPEN FAILURE DURING VALVES CURRENT TEST
Unconditional error, blood pump not available

General description of conditions for occurring:

- TAVA should be open but the measured valve current indicates that it is
closed.

Technical description of conditions for occurring:

- PRI(PI_CurrVaOpenTAVAErrCnt) > 2
- The valve current indicates that TAVA is closed.

Some possible explanations why the error has occurred:

HCEN 9091 Page 76 of 106

- Broken TAVA
- Broken Protective driver board

C COFF 088 106 EVVA OPEN FAILURE DURING VALVES CURRENT TEST
Unconditional error, blood pump not available

General description of conditions for occurring:

- EVVA should be open but the measured valve current indicates that it is
closed.

Technical description of conditions for occurring:

- PRI(PI_CurrVaOpenEVVAErrCnt) > 2
- The valve current indicates that EVVA is closed.

Some possible explanations why the error has occurred:

- Broken EVVA
- Broken Protective driver board

C COFF 088 107 CASE ERROR

Transient error

General description of conditions for occurring:

- Internal software error.

C COFF 088 108 CONDUCTIVITY TEST ERROR,

CONDUCTIVITY IN CPU C UNSTABLE (HIGH CONDUCTIVITY TEST)
Unconditional error, blood pump available

General description of conditions for occurring:

- The conductivity value measured in CPU C is not stable in the high
conductivity test

Technical description of conditions for occurring:

- PRI (PI_CondCHighStableErrCnt) > 4

Some possible explanations why the error has occurred:

- Air in fluid path
- Conductivity cell B is broken or uncalibrated

C COFF 088 109 CONDUCTIVITY TEST ERROR,

GENERAL ERROR (HIGH CONDUCTIVITY TEST)
Unconditional error, blood pump available

General description of conditions for occurring:

- The high conductivity test has not passed within the 20 minutes time limit

Technical description of conditions for occurring:

- PRI (PI_CondTimeOutErrCnt) > 0

Some possible explanations why the error has occurred:

- Air in fluid path
- Conductivity cell B is broken or uncalibrated
- Conductivity cell P is broken or uncalibrated
- Conductivity cell A is broken or uncalibrated

C COFF 088 110 DRVA OPEN FAILURE DURING VALVES CURRENT TEST
Unconditional error, blood pump not available

General description of conditions for occurring:

- DRVA should be open but the measured valve current indicates that it is

HCEN 9091 Page 77 of 106

closed.

Technical description of conditions for occurring:

- PRI(PI_CurrVaOpenDRVAErrCnt) > 2
- The valve current indicates that DRVA is closed.

Some possible explanations why the error has occurred:

- Broken DRVA
- Broken Protective driver board

REMOVED FROM PROGRAM VERSION 11.00

C COFF 088 111 REVA OPEN FAILURE DURING VALVES CURRENT TEST
Unconditional error, blood pump not available

General description of conditions for occurring:

- REVA should be open but the measured valve current indicates that it is
closed.

Technical description of conditions for occurring:

- PRI(PI_CurrVaOpenREVAErrCnt) > 2
- The valve current indicates that REVA is closed.

Some possible explanations why the error has occurred:

- Broken REVA
- Broken Protective driver board

REMOVED FROM PROGRAM VERSION 11.00

C COFF 088 112 ZEVA OPEN FAILURE DURING VALVES CURRENT TEST
Unconditional error, blood pump not available

General description of conditions for occurring:

- ZEVA should be open but the measured valve current indicates that it is
closed.

Technical description of conditions for occurring:

- PRI(PI_CurrVaOpenZEVAErrCnt) > 2
- The valve current indicates that ZEVA is closed.

Some possible explanations why the error has occurred:

- Broken ZEVA
- Broken Protective driver board

REMOVED FROM PROGRAM VERSION 11.00

C COFF 088 113 RIVA OPEN FAILURE DURING VALVES CURRENT TEST
Unconditional error, blood pump not available

General description of conditions for occurring:

- RIVA should be open but the measured valve current indicates that it is
closed.

Technical description of conditions for occurring:

- PRI(PI_CurrVaOpenRIVAErrCnt) > 2
- The valve current indicates that RIVA is closed.

Some possible explanations why the error has occurred:

- Broken RIVA
- Broken Protective driver board

HCEN 9091 Page 78 of 106

REMOVED FROM PROGRAM VERSION 11.00

C COFF 088 114 INVA OPEN FAILURE DURING VALVES CURRENT TEST
Unconditional error, blood pump not available

General description of conditions for occurring:

- INVA should be open but the measured valve current indicates that it is
closed.

Technical description of conditions for occurring:

- PRI(PI_CurrVaOpenINVAErrCnt) > 2
- The valve current indicates that INVA is closed.

Some possible explanations why the error has occurred:

- Broken INVA
- Broken Protective driver board

REMOVED FROM PROGRAM VERSION 11.00

C CO 089, Real Time Clock

C CO 089 000 CASE ERROR
Transient error

General description of conditions for occurring:

- Internal software error

C CO 089 001 REAL TIME CLOCK ERROR (READ)

General description of conditions for occurring:

- I2C error occurred while reading from the real time clock/calendar PCF8573.
The current time and date in the machine may be incorrect.

Technical description of conditions for occurring:

- Real time clock has returned error message

Some possible explanations why the error has occurred:

- Real time clock IC47 (and components) on protective driver board broken

C CO 089 002 REAL TIME CLOCK ERROR (WRITE)

General description of conditions for occurring:

- I2C error occurred while writing to the real time clock/calendar.

Technical description of conditions for occurring:

- Real time clock has returned error message

Some possible explanations why the error has occurred:

- Real time clock IC47 (and components) on protective driver board broken

C CO 089 003 REAL TIME CLOCK ERROR (SAVE)

General description of conditions for occurring:

- An error occurred while saving the year (EEI_TimeNowYear) in the preset
variables. The year value may be incorrect the next time the machine is started.

HCEN 9091 Page 79 of 106

Some possible explanations why the error has occurred:
- Broken SAFE memory

C CO 089 004 REAL TIME CLOCK ERROR (AUTO START)

General description of conditions for occurring:

- During the start-up, the function detected that the alarm was switched ON in
the PCF8573, but there was no valid auto-start status saved in the safe memory
tables. No autoheat nor autorinse will be started.

Some possible explanations why the error has occurred:

- Broken SAFE memory

C CO 090, Protective Vpr Limit Set

C CO 090 000 CASE ERROR
Transient error

General description of conditions for occurring:

- Internal software error

C CO 093, Disinfection Timer

C CO 093 000 CASE ERROR
Transient error

General description of conditions for occurring:

- Internal software error
C CO 094, Decalcification Timer
C CO 094 000 CASE ERROR
Transient error

General description of conditions for occurring:

- Internal software error

HCEN 9091 Page 80 of 106

C FRFF 088, Functional Check Restart
The following error codes are “silent error codes”. If a test corresponding to
each of the error codes fails, the fluid monitor functional check will be restarted
and the error code C FRFF XXX XXX will be stored in the error code buffer. If
the test fails a second time, the error code C COFF XXX XXX will appear, together
with buzzer alarm and spanner key light.

C FRFF 088 055 FUNCTIONAL CHECK RESTARTED

General description of conditions for occurring:

-See C COFF 088 055

C FRFF 088 056 FUNCTIONAL CHECK RESTARTED

General description of conditions for occurring:

-See C COFF 088 056

C FRFF 088 061 FUNCTIONAL CHECK RESTARTED

General description of conditions for occurring:

-See C COFF 088 061

C FRFF 088 065 FUNCTIONAL CHECK RESTARTED

General description of conditions for occurring:

-See C COFF 088 065

C FRFF 088 086 FUNCTIONAL CHECK RESTARTED

General description of conditions for occurring:

-See C COFF 088 086

C FRFF 088 088 FUNCTIONAL CHECK RESTARTED

General description of conditions for occurring:

-See C COFF 088 088

C FRFF 088 092 FUNCTIONAL CHECK RESTARTED

General description of conditions for occurring:

HCEN 9091 Page 81 of 106

-See C COFF 088 092

C FRFF 006, Functional Check Restart

The following error codes are “silent error codes”. If a test corresponding to
each of the error codes fails, the fluid monitor functional check will be restarted
and the error code C FRFF XXX XXX will be stored in the error code buffer. If
the test fails a second time, the error code C COFF XXX XXX will appear, together
with buzzer alarm and spanner key light.

C FRFF 006 003 FUNCTIONAL CHECK RESTARTED

General description of conditions for occurring:

-See C CFF 006 003

HCEN 9091 Page 82 of 106

P PTRA, CPU P transducers
P PTRA 000 100 ERROR READING PARAMETERS FROM BLOOD LEAK DETECTOR
Unconditional error, blood pump not available

General description of conditions for occurring:

- An error occurred while reading transducer parameters during init (start-up).

Some possible explanations why the error has occurred:

- No connection between transducer board and FM I/O board
- No connection between FM I/O board and protective driver board
- Transducer board mounted in incorrect position on FM I/O board
- Incorrect transducer ID. Please update transducer ID (I2C scan).
- Transducer board is broken
- Serial bus error on protective CPU board
- Uncalibrated transducer. Please calibrate transducer
- Broken FM I/O board

P PTRA 000 101 ERROR READING PARAMETERS FROM CONDUCTIVITY CELL P (COND)
Unconditional error, blood pump not available

General description of conditions for occurring:

- An error occurred while reading transducer parameters during init (start-up).

Some possible explanations why the error has occurred:

- No connection between transducer board and protective driver board
- Incorrect transducer ID. Please update transducer ID (I2C scan).
- Transducer board is broken
- Serial bus error on protective CPU board
- Uncalibrated transducer. Please calibrate transducer

P PTRA 000 102 ERROR READING PARAMETERS FROM CONDUCTIVITY CELL P (TEMP)
Unconditional error, blood pump not available

General description of conditions for occurring:

- An error occurred while reading transducer parameters during init (start-up).

Some possible explanations why the error has occurred:

P PTRA 000 103 ERROR READING PARAMETERS FROM DIALYSIS PRESSURE TRANSDUCER
Unconditional error, blood pump not available

General description of conditions for occurring:

- An error occurred while reading transducer parameters during init (start-up).

Some possible explanations why the error has occurred:

HCEN 9091 Page 83 of 106

P PTRA 000 104 ERROR READING PARAMETERS FROM VENOUS PRESSURE TRANSDUCER
Unconditional error, blood pump not available

General description of conditions for occurring:

- An error occurred while reading transducer parameters during init (start-up).

Some possible explanations why the error has occurred:

- No connection between transducer board and BM I/O board
- No connection between BM I/O board and protective driver board
- Transducer board mounted in incorrect position on BM I/O board
- Incorrect transducer ID. Please update transducer ID (I2C scan).
- Transducer board is broken
- Serial bus error on protective CPU board
- Uncalibrated transducer. Please calibrate transducer
- Broken BM I/O board

P PTRA 000 105 ERROR READING PARAMETERS FROM PH TRANSDUCER

Unconditional error, blood pump not available

General description of conditions for occurring:

- An error occurred while reading transducer parameters during init (start-up).

Some possible explanations why the error has occurred:

- No connection between MM I/O board and protective CPU board
- Incorrect transducer ID. Please update transducer ID (I2C scan).
- MM I/O board is broken
- Serial bus error on protective CPU board
- Uncalibrated transducer. Please calibrate transducer

P PTRA 000 106 ERROR READING PARAMETERS FROM ARTERIAL PRESSURE TRANSDUCER
Unconditional error, blood pump not available

General description of conditions for occurring:

- An error occurred while reading transducer parameters during init (start-up).

Some possible explanations why the error has occurred:

HCEN 9091 Page 84 of 106

C Cx 000 xxx, Transition Controller
C Cx 000 001 Pxxx ttt Process nr xxx out of range in transition test
C Cx 000 002 Pxxx yyy State nr yyy out of range
C Cx 000 003 Pxxx ttt Test nr ttt out of range in transition test
C Cx 000 004 P000 xxx Process state shadow table corrupt in process xxx
C Cx 000 005 Pxxx yyy Process attempt to assume non-defined state yyy
C Cx 000 006 Pxxx yyy State yyy attempt to control process at own or higher level
C Cx 000 007 Pxxx yyy State yyy attempt to control non-defined process
C Cx 000 008 Pxxx yyy State yyy attempt to control non-defined function
C Cx 000 009 Pxxx yyy State yyy attempt to duplicate process control
C Cx 000 010 Pxxx yyy State yyy attempt to duplicate function control
C Cx 000 011 Pxxx yyy State yyy attempt to reference non-defined event control
C Cx 000 012 Pxxx yyy State yyy attempt to set non-defined event mode
C Cx 000 013 P000 fff Non-controlled function fff
C Cx 000 014 Pxxx yyy State yyy attempt to set non-existant output cross reference
C Cx 000 015 jjjj iii Crossreference iii references non-existant logical output jjjj
C Cx 000 016 P000 fff Function shadow table corrupt in function fff
C Cx 000 017 jjjj iii Logical output corrupt. Crossreference iii references to logical output table. jjjj
references to index in lit file.

Unconditional error, blood pump not available

Some possible explanations why the error has occurred:

HCEN 9091 Page 86 of 106

- Internal software error

C CSYS 000 011 PROGRAM VERSION ERROR, CPU C

General description of conditions for occurring:

- An illegal combination of PROMS were detected at start-up

Some possible explanations why the error has occurred:

- The CPU C EPROMS are not approved (in combination with P and W)

C CSYS 000 012 PROGRAM VERSION ERROR, CPU P

General description of conditions for occurring:

- An illegal combination of PROMS were detected at start-up

Some possible explanations why the error has occurred:

- The CPU P EPROMS are not approved (in combination with C and W)

C CSYS 000 013 PROGRAM VERSION ERROR, CPU W

General description of conditions for occurring:

- An illegal combination of PROMS were detected at start-up

Some possible explanations why the error has occurred:

- The CPU W EPROM is not approved (in combination with C and P)

C CSYS 000 014 PROGRAM VERSION ERROR, CPU C AND CPU P

General description of conditions for occurring:

- An illegal combination of PROMS were detected at start-up

Some possible explanations why the error has occurred:

- The CPU C and P EPROMS are not approved (in combination with W)

C CSYS 000 015 PROGRAM VERSION ERROR, CPU C AND CPU W

General description of conditions for occurring:

- An illegal combination of PROMS were detected at start-up

Some possible explanations why the error has occurred:

- The CPU C and W EPROMS are not approved (in combination with P)

C CSYS 000 016 PROGRAM VERSION ERROR, CPU P AND CPU W

General description of conditions for occurring:

- An illegal combination of EPROMS were detected at start-up

Some possible explanations why the error has occurred:

C CSYS 000 208 TASK TIME-OUT

General description of conditions for occurring:

- The Fcn_Task_3 is not running

Some possible explanations why the error has occurred:

- Internal software error

HCEN 9091 Page 88 of 106

C CSYS 000 403 COMMUNICATION HANDLING ERROR

General description of conditions for occurring:

- The communication handling is malfunctioning

Some possible explanations why the error has occurred:

- Internal software error

HCEN 9091 Page 90 of 106

C EBUF 000 000, Error Code Buffer
C EBUF 000 000 Error code buffer corrupt

General description of conditions for occurring:

- The checksum protecting the error code buffer is corrupt. Restart the AK 95

Some possible explanations why the error has occurred:

- Broken/corrupt Safe-RAM on control CPU board

HCEN 9091 Page 91 of 106

C SYS 001 001 FLOAT REAL OVERFLOW IN CPU C

Some possible explanations why the error has occurred:

HCEN 9091 Page 92 of 106

- Internal software error

C SYS 001 002 FLOAT INTEGER OVERFLOW IN CPU C

Some possible explanations why the error has occurred:

- Internal software error

C SYS 001 003 UNDEFINED MESSAGE IN CPU C

Some possible explanations why the error has occurred:

- Internal software error

P SYS 000 000 DIVIDE ERROR, DIVISION BY 0, IN CPU P

P SYS 000 008 RESERVED VECTOR IN CPU P

Some possible explanations why the error has occurred:

HCEN 9091 Page 93 of 106

- Internal software error

P SYS 000 040 UNKNOWN INTERRUPT IN CPU P

Some possible explanations why the error has occurred:

- Internal software error
- Broken protective CPU board

P SYS 001 000 FLOAT ILLEGAL OPCODE IN CPU P

Transient error

Some possible explanations why the error has occurred:

- Internal software error

P SYS 001 001 FLOAT REAL OVERFLOW IN CPU P

Some possible explanations why the error has occurred:

- Internal software error

P SYS 001 002 FLOAT INTEGER OVERFLOW IN CPU P

Some possible explanations why the error has occurred:

- Internal software error

P SYS 001 003 UNDEFINED MESSAGE IN CPU P

Some possible explanations why the error has occurred:

- Internal software error

HCEN 9091 Page 94 of 106

P ENV, CPU P ENVIRONMENT
P ENV 001 001 DEAIRATING CHAMBER ERROR

General description of conditions for occurring:

- The level detected in deairating chamber was both high AND low
- This was detected for more than 5 seconds.

Some possible explanations why the error has occurred:

- IC 28 on protective driver board broken
- Broken level switch

P ENV 001 002 DEAIRATING CHAMBER HIGH LEVEL ERROR

General description of conditions for occurred:

-The level in the deairating chamber has been high for more than 45 seconds
during treatment

Some possible explanations why the error has occurred:

- EVVA leakage.
- The tube between deairating chamber and EVVA is leaking.
- Level detector could be stuck.
-There has been a very high positive pressure in the chamber. This pressure is
> 300 mmHg.

HCEN 9091 Page 95 of 106

P POW, Power ON/OFF Functions
P POW 001 001 PLD VERIFY ERROR

General description of conditions for occurring:

PLD verify error at power up. Once every 50 ms the REMO verify signal
(REMOVFY) is checked. If it is active during 100 loops (i.e. 5 seconds) then
this error code is issued and an ON/OFF key activation is started. (The
PONKY signal is set until REMOVFY disappears, then the PONKY signal is
reset.)

Some possible explanations why the error has occurred:

- Broken protective driver board (IC 16)

HCEN 9091 Page 96 of 106

P PPR, Program Flow (CPU P)
P PPR 000 xxx PROGRAM FLOW ERROR

General description of conditions for occurring:

- A program flow error was detected by CPU P

Some possible explanations why the error has occurred:

- Internal software error

HCEN 9091 Page 97 of 106

HCEN 9091 Page 98 of 106

P PREC, Recovery Functions
P PREC 000 000 SAFE-RAM CHECKSUM ERROR
Transient error

General description of conditions for occurring:

Checksum error in both recovery banks, detected at startup.

Some possible explanations why the error has occurred:

- Broken CPU P safe-RAM

P PREC 001 00x SAFE-RAM CHECKSUM ERROR

General description of conditions for occurring:

Checksum error in recovery bank x, detected when writing new values. If this
message is not followed by P PREC 002 000, the error was repaired by
copying the values of the other recovery bank.

Some possible explanations why the error has occurred:

- Broken CPU P safe-RAM

P PREC 002 000 SAFE-RAM CHECKSUM ERROR

Transient error

General description of conditions for occurring:

Checksum error in both recovery banks, detected when writing new values.
The error could not be repaired. This error is preceded by the message P
PREC 001 00x

Some possible explanations why the error has occurred:

- Broken CPU P safe-RAM

HCEN 9091 Page 99 of 106

P SDT, CPU P system
P SDT 003 001 CHECK SUM ERROR
Unconditional error, blood pump not available

General description of conditions for occurring:

- The check sum of the protective system presets is not correct. Enter service/
preset and preset the machine (make a default preset).

Some possible explanations why the error has occurred:

- Broken/ new CPU P safe-RAM

Some possible explanations why the above error has occurred:

- Internal software error

P SDT 004 006 MAIN RESET FAILURE (CPU W)

Some possible explanations why the above error has occurred:

- Internal software error

P SDT 004 007 THE CPU P CHEM FLAG INCORRECTLY SET

Some possible explanations why the above error has occurred:

- Internal software error
- Corrupt safe-RAM

P SDT 004 008 REQUEST ERROR

General description of conditions for occurring:

- A single request of signal bmfchpart1, bmfchpart2, fmfchpart1 or fmfchpart2
has been performed.

Some possible explanations why the above error has occurred:

- Internal software error

HCEN 9091 Page 100 of 106

P SDT 004 009 REQUEST ERROR
Transient error

General description of conditions for occurring:

- The control system requested a reset to exit maintenance mode. The
protective system was not in maintenance mode.

Some possible explanations why the above error has occurred:

- Internal software error

P SDT 038 001 PRESET ERROR

General description of conditions for occurring:

- The preset acetate concentrate bank is not set to a valid value.

Some possible explanations why the above error has occurred:

- Internal software error
- Corrupt SAFE -RAM (please make a default preset)

P SDT 038 002 PRESET ERROR

General description of conditions for occurring:

- The preset bicarbonate concentrate bank is not set to a valid value.
- Corrupt SAFE -RAM (please make a default preset)

P SDT 044 001 PROGRAM FLOW ERROR

Unconditional error, blood pump not available

General description of conditions for occurring:

- AK 95 was reset by CPU P due to a failure in the program flow supervision.

Some possible explanations why the above error has occurred:

- Internal software error
- Broken communication between CPU P and CPU or CPU W
- Broken protective CPU board
- Broken control CPU board
- Broken AC/DC unit (check the +5 voltages)

HCEN 9091 Page 101 of 106

W WAD, CPU W Check Sum
W WAD 000 000 CPU W, CHECK SUM ERROR
Transient error

General description of conditions for occurring:

- The check sum on CPU W A/D reference value is corrupted. Calibrate the
A/D converter.

HCEN 9091 Page 102 of 106

W WPR, Program Flow (CPU W)
W WPR 000 xxx PROGRAM FLOW ERROR

General description of conditions for occurring:

- A program flow error was detected by CPU W

Some possible explanations why the error has occurred:

- Internal software error (see table below)

countRecI2C: Signal received in W environment

countSendI2C: Signal sent from W environment
countXOutEnv: Signal sent from W SDT
countXInEnv: Signal received in W SDT

Table 1. Explanation of W WPR 000 xxx

xxx countRecI2C countSendI2C countXOutEnv countXInEnv
000
001 OK
002 OK
003 OK OK
004 OK
005 OK OK
006 OK OK
007 OK OK OK
008 OK
009 OK OK
010 OK OK
011 OK OK OK
012 OK OK
013 OK OK OK
014 OK OK OK
015 OK OK OK OK

HCEN 9091 Page 103 of 106

HCEN 9091 Page 104 of 106

? UDEF xxx xxx, Undefined error
? UDEF xxx xxx UNDEFINED ERROR

General description of conditions for occurring:

- Undefined error ! Please report to Gambro Technical Service

HCEN 9091 Page 105 of 106

Computer start-up sequence
The table below is a brief sequence diagram of the start in each CPU.
The number in brackets refer to number shown on LED display at start-up.

CPU C CPU P CPU W

Hardware reset from AC/DC
unit.
Initialization. of I/O ports.
Release reset signals to CPU C
and CPU P
Initialization. of chip select Initialization. of chip select Cold or warm start? (1)
logic. logic. If warmstart jump to A

Initialization. of I/O ports and Initialization. of I/O ports and Internal memory and register
timers. timers. verification. (2)

Cold or warm start? (1) Cold or warm start? (1) Program verification. (3)
If warmstart jump to A If warmstart jump to A

CPU register verification. (2) CPU register verification. (2) Data memory verification. (4)
Data memory init. (5)
Program verification. (3) Program verification. (3)

Data memory verification. (4) Data memory verification. (4) LABEL A

Data memory init. (5) Data memory init. (5)
Accomplish initialization. state
according to ANSI C standard

LABEL A LABEL A Start of C program. (6)

Accomplish initialization. state Accomplish initialization. state Initialization. and start

according to ANSI C standard. according to ANSI C standard. application.

OS start (6) OS start (6)

Start of initialization. Task Start of initialization. task

Function initialization.

If warmstart get recover

information.

Start all task

33 @FRI( FI_FlowPumpCycle ), Scale_Factor_10, Flow pump duty cycle

Scale: 1%

34 @FRI( FI_DegassPr ), Scale_Factor_10, Degassing pressure

Scale: 1mmHg

35 @FRI( FI_UFVol ), Scale_Factor_1, UF volume (accumulated).

Scale: 1 ml

36 @FRI( FI_UFRate ), Scale_Factor_1000, UF rate.

Scale: 1/1000 l/h

37 @FRI( FI_UFRateDisp ), Scale_Factor_1000, UF rate.

Scale: 1/1000 l/h

38 @FRI( FI_UFCoilCurrent ), Scale_Factor_10, Coil current trough UF-cell.

Scale: 1mA

39 @FRI( FI_TarTimer ), Scale_Factor_1, UF Taration timer

40 @FRI( FI_UFCalIsolVol ), Scale_Factor_10, Isolated UF, calibration,

volume. Scale: 1 ml

41 @FRI( FI_UFCalVolDiff ), Scale_Factor_100, UF calibration volume

difference from ref.
Scale: 1%.

42 @FRI( FI_UFCalIsolVolDiff ), Scale_Factor_100, Isolated UF calibration

volume difference from ref.
Scale: 1%

43 @BRI( BI_VenPr ), Scale_Factor_10, Venous Pressure (CPU C)

Scale: 1mmHg

44 @ORI( OI_UFCalRefVol ), Scale_Factor_10, UF reference volume,

calibration.
Scale: 1/10 ml

45 @ORI( OI_NonDiffTime ), Scale_Factor_1, Non diffusion time.

Scale : 1 min

46 @ORI( OI_PassedTime ), Scale_Factor_1, Passed time.

Scale : 1 min

47 @FRI( FI_UFCalVol ), Scale_Factor_10, UF calibration volume

51 @PRI( PI_DiaPrMeas ), Scale_Factor_10, Dialysis pressure

Scale: 1mmHg
Available in service mode
Use SRP 4,avail. in all modes

52 @FRI( FI_CondPAvg ), Scale_Factor_100, Average condP value

Scale: 1/100 mS/cm

53 @PRI( PI_BlLeakMeasLog ), Scale_Factor_1, Blood leak value

Scale: 1BLU

54 @FRI( FI_SucPumpCurrent ), Scale_Factor_1, Suction pump current

Scale: 1mmHg

55 @FRI( FI_SucPumpCycle ), Scale_Factor_10, Suction pump dutycycle

Scale: 1%
56 @FRI( FI_PumpSpeedRatio ), Scale_Factor_10, Pump speed ratio in
bicarbonate mode

57 @PRI( PI_AprTstCnt ), Scale_Factor_1), Arterial pressure zero test

approved, only for logg.

58 @FRI( FI_DiaFlow ), Scale_Factor_1), Approx flowrate

59 @FRI( FI_VarFlowMotorPosition ),Scale_Factor_1); Position of motor for

variable flow

Page: 2
P 12.20

SRL Array, Boolean variables

0 @PRL( P_PrimDetBlood ), Scale_Factor_1, Priming detector (TRUE=blood)

1 @PRL( P_BlPumpCoverOpen ), Scale_Factor_1, Blood pump cover open

2 @PRL( P_NoAir ), Scale_Factor_1, Air detector.Active in

service. Use SRI 29,avail.
in all modes

3 @PRL( P_FlowSwitchFlow ), Scale_Factor_1, Flow switch (TRUE=flow)

4 @PRL( P_HeaterEnergizedLog), Scale_Factor_1, Heater energized

(signal PMAINS)

5 @BRL( B_VenClampClosed ), Scale_Factor_1, Venous clamp closed

6 @BRL( B_HepPumpOvldAttn ), Scale_Factor_1, Heparinpump overload

7 @PRL( P_DiaConByp ), Scale_Factor_1, Diaconnectors in bypass

8 @PRL( P_DiaConDia ), Scale_Factor_1, Diaconnectors on dialyzer

9 @PRL( P_SAGSLog ), Scale_Factor_1, SAGS status

10 @PRL( P_AprAlarmLog ), Scale_Factor_1, Arterial guard activated

11 @BRL( B_ArtClampClosed ), Scale_Factor_1, Arterial clamp closed

16 @FRL( F_InPressOk ), Scale_Factor_1, INPS activated

17 @FRL( F_InValveOpen ), Scale_Factor_1, INVA open

18 @FRL( F_FLVASts ), Scale_Factor_1, FLVA in priming mode=TRUE

19 @FRL( F_BicLatchOpen ), Scale_Factor_1, BiCart latches open

20 @FRL( F_DRVASts ), Scale_Factor_1, DRVA open

21 @FRL( F_RIVASts ), Scale_Factor_1, RIVA open

23 @FRL( F_HPGHigh ), Scale_Factor_1, HPG activated (>450mmHg)

24 @ORL( O_DIVAOpen), Scale_Factor_1, DIVA open

27 @ORL( O_BYVAOpen ), Scale_Factor_1, BYVA open

30 @PRL( P_TAVAOpen ), Scale_Factor_1, TAVA open

31 @PRL( P_EVVAOpen ), Scale_Factor_1, EVVA open

32 @FRL( F_ZEVASts ), Scale_Factor_1, ZEVA open

Status info for uf calib.
Available in service mode
Use SRI 18,avail. in all

Page: 3
P 12.20

modes

56 @FRL( F_FIVASts ), Scale_Factor_1, Status signal indicating

whether FIVA is activated
or not.
57 @PRL( P_DiaCon1Status ), Scale_Factor_1, Status of PEXSG1

58 @PRL( P_DiaCon2Status ), Scale_Factor_1, Status of PEXSG2

59 @FRL( F_UPSSts ), Scale_Factor_1); Status signal indicating

whether UPS is activated
or not.

60 @FRL( F_BattSts ), Scale_Factor_1); Battery Backup activated

or not.

SRP variables, Protective system variables (available in all modes)

0 @cLogPWord, Scale_Factor_10, Venous Pressure (CPU P)

Scale: 1mmHg

1 @cLogPWord, Scale_Factor_10, TMP

Scale: 1mmHg

2 @cLogPWord, Scale_Factor_100, Temperature (CPU P)

Scale: 1 degree C

3 @cLogPWord, Scale_Factor_100, Conductivity (CPU P)

Scale: 1mS/cm

4 @cLogPWord, Scale_Factor_10); Dialysis pressure, pd (CPU P)

Scale: 1mmHg

SRR array, Real variables

0 @FRR( FR_UFRate ), Scale_Factor_1, UF-rate. Skale l/h

1 @FRR( FR_Ch1Rate ), Scale_Factor_1, Channel 1 rate.

Scale ml/min

2 @FRR( FR_Ch2Rate ), Scale_Factor_1, Channel 2 rate.

Scale ml/min

3 @FRR( FR_CalCh1ROffset ), Scale_Factor_1, Calibration real offset ch1

4 @FRR( FR_CalCh2ROffset ), Scale_Factor_1, Calibration real offset ch2

5 @FRR( FR_CalCh1RCoeff ), Scale_Factor_1, Calibration real coeff ch1

6 @FRR( FR_CalCh2RCoeff ), Scale_Factor_1, Calibration real coeff ch2

7 @FRR( FR_Ch1ROffset ), Scale_Factor_1, UF channel 1 offset

Channel 1 rate offset
calibration factor.
Scale: 1 ml / min

8 @FRR( FR_Ch2ROffset ), Scale_Factor_1, UF channel 2 offset

Channel 2 rate offset
calibration factor.
Scale: 1 ml / min

9 @FRR( FR_Ch1RCoeff ), Scale_Factor_1, UF channel 1 coeff

Channel 1 rate coefficient
calibration factor.

10 @FRR( FR_Ch2RCoeff ), Scale_Factor_1, UF channel 2 coeff

Channel 2 rate coefficient
calibration factor.

11 @FRR( FR_CalUFRTolerance ), Scale_Factor_1, Calibration UF rate tolerance

12 @FRR( FR_CalUFROffset ), Scale_Factor_1, Calibration UF rate offset

13 @FRR( FR_UFRTolerance ), Scale_Factor_1, UF-rate tolerance.

14 @FRR( FR_UFROffset ), Scale_Factor_1, UF-rate offset calibration

factor.
Scale: 1 ml / min

15 @VFC1.Value, Scale_Factor_1, Voltage-to-frequency

converter for channel 1
Last measured value for the
currently selected parameter.

16 @VFC1.Offset, Scale_Factor_1, Voltage-to-frequency

converter for channel 1
Offset measured (input=ZOVR)

Page: 4
P 12.20

by the converter.

17 @VFC1.Ref, Scale_Factor_1, Voltage-to-frequency

converter for channel 1
Reference voltage measured
by the converter.

18 @VFC1.Mean, Scale_Factor_1, Voltage-to-frequency

converter for channel 1
The mean value for the latest
measurment interval when
auto.statistics is enabled.

19 @VFC1.Var, Scale_Factor_1, Voltage-to-frequency

converter for channel 1
The variance for the latest
measurment interval when
auto.statistics is enabled.

20 @VFC2.Value, Scale_Factor_1, Voltage-to-frequency

converter for channel 2
Last measured value for the
currently selected parameter.

21 @VFC2.Offset, Scale_Factor_1, Voltage-to-frequency

converter for channel 2
Offset measured (input=ZOVR)
by the converter.

22 @VFC2.Ref, Scale_Factor_1, Voltage-to-frequency

converter for channel 2
Reference voltage measured
by the converter.

23 @VFC2.Mean, Scale_Factor_1, Voltage-to-frequency

converter for channel 2
The mean value for the latest
measurment interval when
auto.statistics is enabled.

24 @VFC2.Var, Scale_Factor_1, Voltage-to-frequency

converter for channel 2
The variance for the latest
measurment interval when
auto.statistics is enabled.

25 @VFC3.Value, Scale_Factor_1, Voltage-to-frequency

converter for channel 3
Last measured value for the
currently selected parameter.

26 @VFC3.Offset, Scale_Factor_1, Voltage-to-frequency

converter for channel 3
Offset measured (input=ZOVR)
by the converter.

27 @VFC3.Ref, Scale_Factor_1, Voltage-to-frequency

converter for channel 3
Reference voltage measured
by the converter.

28 @VFC3.Mean, Scale_Factor_1, Voltage-to-frequency

converter for channel 3
The mean value for the latest
measurment interval when
auto.statistics is enabled.

29 @VFC3.Var, Scale_Factor_1 ); Voltage-to-frequency

converter for channel 3
The variance for the latest
measurment interval when
auto.statistics is enabled.

SRB Array, byte variables

1 ( FDTRC$SELECT$PROC ), Scale_Factor_1

2 ( FDTRC$HEATER$ENABLE$CTRL$PROC ) Scale_Factor_1,

3 ( FDTRC$SAGS$TEST$PROC ), Scale_Factor_1,

4 ( FDTRC$SAGS$TEST$DRAIN$PROC ), Scale_Factor_1,

5 ( FDTRC$VALVE$TEST$PROC ), Scale_Factor_1,

6 ( FDTRC$DISINFECTION$PROC ), Scale_Factor_1,

7 ( FDTRC$CONC$FILLUP$PROC ), Scale_Factor_1,

8 ( FDTRC$CENTR$FILLUP$PROC ), Scale_Factor_1,

Page: 5
P 12.20

9 ( FDTRC$DIL$FILLUP$PROC ), Scale_Factor_1,

10 ( FDTRC$CLEAN$CART$PRIM$PROC ), Scale_Factor_1,

11 ( FDTRC$CLEAN$CART$FILL$PROC ), Scale_Factor_1,

12 ( FDTRC$CITRIC$DWELL$PROC ), Scale_Factor_1,

13 ( FDTRC$RINSE$PROC ), Scale_Factor_1,

14 ( FDTRC$HEAT$DIS$TEST$PROC ), Scale_Factor_1,

15 ( FDTRC$HEAT$DIS$FLUSH$PROC ), Scale_Factor_1,

16 ( FDTRC$DRAIN$PROC ), Scale_Factor_1,

17 ( FDTRC$DISINFECTION$TIME$PROC ) Scale_Factor_1,

18 ( FDTRC$STICK$A$RESOLVER$PROC ), Scale_Factor_1,

19 ( FDTRC$STICK$B$RESOLVER$PROC ), Scale_Factor_1,

20 ( FDTRC$BIC$LATCH$RESOLVER$PROC) Scale_Factor_1,

21 ( FDTRC$CHEM$FILLUP$RDY$LATCH$PROC ), Scale_Factor_1,

22 ( FDTRC$DISINF$CTRL$PROC ), Scale_Factor_1,

23 ( FDTRC$DRAIN$BEF$CHEM$DIS$PROC Scale_Factor_1,

24 ( FFTRC$FCH$MAIN$PROC ), Scale_Factor_1,

25 ( FFTRC$DISINFECT$VALVES$PROC ), Scale_Factor_1,

26 ( FFTRC$DEGASS$PR$TEST$PROC ), Scale_Factor_1,

27 ( FSTRC$UF$CALIBRATION$PROC ), Scale_Factor_1,

28 ( FSTRC$DRAIN$REF$VOL$PROC ), Scale_Factor_1,

29 ( FSTRC$UF$CALIB$PREP$PROC ), Scale_Factor_1,

30 ( FSTRC$UF$MAIN$FL$OFFSET$PROC ) Scale_Factor_1,

31 ( FSTRC$UF$CH1$FLOW$CAL$PROC ), Scale_Factor_1,

32 ( FSTRC$UF$DIFF$CAL$PROC ), Scale_Factor_1,

33 ( FSTRC$VERIFY$UF$PROC ), Scale_Factor_1,

34 ( FSTRC$UF$ISOL$VERIFY$PROC ), Scale_Factor_1,

35 ( @FFCNSTATE(FF_VARFLOWMOTOR ), Scale_Factor_1,

Page: 6

User Manual Fotona
100% (7)
User Manual Fotona
103 pages
Ziehm Vision RFD 3D Service Manual
100% (22)
Ziehm Vision RFD 3D Service Manual
820 pages
Carestation 620 - Manual Técnico - Inglês
100% (7)
Carestation 620 - Manual Técnico - Inglês
530 pages
FLOW-I Service Manual
100% (1)
FLOW-I Service Manual
384 pages
OEC One Service Manual SM 6888001-1EN 5
100% (3)
OEC One Service Manual SM 6888001-1EN 5
319 pages
Operating Instructions 4008s
67% (3)
Operating Instructions 4008s
353 pages
GE XR6000 X-Ray - Service Manual
91% (44)
GE XR6000 X-Ray - Service Manual
422 pages
YL0419-04142 - Service Manual For Lightlas Selector Deux
100% (3)
YL0419-04142 - Service Manual For Lightlas Selector Deux
142 pages
IClave Plus Techincal Manual
100% (1)
IClave Plus Techincal Manual
95 pages
KONICA MINOLTA CS7 Installation & Service Manual
88% (17)
KONICA MINOLTA CS7 Installation & Service Manual
788 pages
AquaWTU SM 04A-2018 SW 01 3x EN F40007839
100% (3)
AquaWTU SM 04A-2018 SW 01 3x EN F40007839
174 pages
Drager Fabius - Service Manual PDF
97% (31)
Drager Fabius - Service Manual PDF
328 pages
Philips BV Endura Service Manual Frogenore PDF
50% (10)
Philips BV Endura Service Manual Frogenore PDF
5 pages
FONA ART Plus Service Manual GB Rev 6 - 18030
100% (1)
FONA ART Plus Service Manual GB Rev 6 - 18030
40 pages
Whitestar Signature Service Manual Actualizado
100% (2)
Whitestar Signature Service Manual Actualizado
274 pages
Versana Active Spec Sheet
100% (1)
Versana Active Spec Sheet
19 pages
Instruction Manual For Installation LIGHTSPEED 16 RT CT
100% (5)
Instruction Manual For Installation LIGHTSPEED 16 RT CT
52 pages
Wa0003
75% (8)
Wa0003
276 pages
Gambro AK 200 S - Service Manual
83% (12)
Gambro AK 200 S - Service Manual
315 pages
Nipro Surdial 55+ Dialysis Machine - Service Manual PDF
94% (16)
Nipro Surdial 55+ Dialysis Machine - Service Manual PDF
456 pages
Service Manual BV Family R1.2
90% (10)
Service Manual BV Family R1.2
123 pages
Ak 98 Error Code
100% (3)
Ak 98 Error Code
381 pages
Gambro Ak 96 Service Manual
38% (8)
Gambro Ak 96 Service Manual
2 pages
AK 96 Spare Parts List Low Resolution
100% (1)
AK 96 Spare Parts List Low Resolution
74 pages
4008 E / 4008 B / 4008 H / 4008 S Hemodialysis System Technical Manual
100% (3)
4008 E / 4008 B / 4008 H / 4008 S Hemodialysis System Technical Manual
350 pages
4008 S Hemodialysis Device Service Manual: Software Version: 12.0 Edition: 11A-2016 Part No.: F40005024
100% (1)
4008 S Hemodialysis Device Service Manual: Software Version: 12.0 Edition: 11A-2016 Part No.: F40005024
444 pages
4008S (NG) Op 04 12 10 SW 11 10 en
100% (10)
4008S (NG) Op 04 12 10 SW 11 10 en
318 pages
Nipro Surdial 55 Plus Machine PDF
100% (9)
Nipro Surdial 55 Plus Machine PDF
13 pages
DFS Pressure Test 12500 (TR56) PDF
100% (3)
DFS Pressure Test 12500 (TR56) PDF
4 pages
Service Code and Password For Medical Equipments
100% (10)
Service Code and Password For Medical Equipments
3 pages
DBB-27 Technical Manual
No ratings yet
DBB-27 Technical Manual
140 pages
4008 Series Catalogue 2013 (External) - 1
No ratings yet
4008 Series Catalogue 2013 (External) - 1
39 pages
User Manual (Point 200HD)
No ratings yet
User Manual (Point 200HD)
46 pages
TR-8000 Manual Tecnico
100% (2)
TR-8000 Manual Tecnico
65 pages
Training Center: Bicarb Mixing Ratio
100% (3)
Training Center: Bicarb Mixing Ratio
35 pages
Nipro Diamax Dialysis Machine - Service Manual PDF
80% (15)
Nipro Diamax Dialysis Machine - Service Manual PDF
303 pages
Nipro Surdial 55+ Dialysis Machine - Maintenance Manual 1
100% (8)
Nipro Surdial 55+ Dialysis Machine - Maintenance Manual 1
126 pages
6th Central Pay Commission Salary Calculator
100% (436)
6th Central Pay Commission Salary Calculator
15 pages
IDTechEx Samplepages FlexiblePrintedElectronics20232033ForecastsTechnologiesMarkets
No ratings yet
IDTechEx Samplepages FlexiblePrintedElectronics20232033ForecastsTechnologiesMarkets
29 pages
Hemodialise - Gambro AK96 - Códigos de Erros
67% (3)
Hemodialise - Gambro AK96 - Códigos de Erros
91 pages
AK96 Error Code 350
71% (7)
AK96 Error Code 350
132 pages
TechnicalErrors 98
No ratings yet
TechnicalErrors 98
242 pages
Trouble Shooting Guide For Fresenius 4008 Hemodialysis Units
67% (3)
Trouble Shooting Guide For Fresenius 4008 Hemodialysis Units
9 pages
Fresenius Error Messages 4008
80% (5)
Fresenius Error Messages 4008
5 pages
Ak 96 Fluid Unit - Flow Path: (Upgrade Kit)
100% (1)
Ak 96 Fluid Unit - Flow Path: (Upgrade Kit)
1 page
4008S Service Manual
85% (26)
4008S Service Manual
595 pages
Dialog+ SW9.xx, Service Manual, Chapter 4, TSM Service Program, Edition 2013 (EN) PDF
100% (2)
Dialog+ SW9.xx, Service Manual, Chapter 4, TSM Service Program, Edition 2013 (EN) PDF
181 pages
TI 2018 - 04 Software Version 9.1B (EN)
100% (7)
TI 2018 - 04 Software Version 9.1B (EN)
56 pages
DFS Pressure Test 12650 2 (TR59) PPTX
100% (2)
DFS Pressure Test 12650 2 (TR59) PPTX
9 pages
4008 Series Catalogue 2011 (External)
67% (9)
4008 Series Catalogue 2011 (External)
39 pages
Aun Dialog+ Dialysis Machine - Service Manual 1000
100% (1)
Aun Dialog+ Dialysis Machine - Service Manual 1000
455 pages
Manuarl Instruction Stern Weber Dental U
100% (1)
Manuarl Instruction Stern Weber Dental U
84 pages
User Manual Ritter A Series Dental System
0% (1)
User Manual Ritter A Series Dental System
39 pages
715-80 Exilis Operators Manual EN201
No ratings yet
715-80 Exilis Operators Manual EN201
38 pages
ELV Systems Engineer - M.noman Bhatti
0% (2)
ELV Systems Engineer - M.noman Bhatti
2 pages
Controlling Mind
No ratings yet
Controlling Mind
8 pages
B603 Series Users Manual PDF
No ratings yet
B603 Series Users Manual PDF
36 pages
Gambro Ak 200
40% (5)
Gambro Ak 200
116 pages
A K 2 0 0 S e R R o R M e S S A G e e X P L A N A T I o N S
50% (2)
A K 2 0 0 S e R R o R M e S S A G e e X P L A N A T I o N S
128 pages
Troubleshooting Fresenius 4008S Hemodialysis Machine
100% (9)
Troubleshooting Fresenius 4008S Hemodialysis Machine
11 pages
AK 96 Service Manual - General Information 1:1
100% (1)
AK 96 Service Manual - General Information 1:1
6 pages
AK 98 Preset Editor User Instructions
No ratings yet
AK 98 Preset Editor User Instructions
16 pages
4008 H / 4008 S Hemodialysis Machine Technical Manual: Supplemental Instructions For The OCM Option Part No.: M32 514 1
No ratings yet
4008 H / 4008 S Hemodialysis Machine Technical Manual: Supplemental Instructions For The OCM Option Part No.: M32 514 1
75 pages
Hemo Dialysis Maintenance
100% (1)
Hemo Dialysis Maintenance
15 pages
Surdial Service Manual PDF
100% (1)
Surdial Service Manual PDF
130 pages
Hemo Dialysis Maintenance
100% (3)
Hemo Dialysis Maintenance
14 pages
Maintenance Manual AK200
100% (6)
Maintenance Manual AK200
31 pages
4008 B / 4008 H / 4008 S Hemodialysis Device Technical Manual
No ratings yet
4008 B / 4008 H / 4008 S Hemodialysis Device Technical Manual
378 pages
Manual Tecnico Maquina de Dialisis 4008H 4008S PDF
No ratings yet
Manual Tecnico Maquina de Dialisis 4008H 4008S PDF
75 pages
TRBI 100A维修
No ratings yet
TRBI 100A维修
96 pages
Trouble Shooting Diamax
No ratings yet
Trouble Shooting Diamax
177 pages
Surdial Service Manual
67% (3)
Surdial Service Manual
130 pages
Ak98 Preset List
No ratings yet
Ak98 Preset List
21 pages
H30&H50 Troubleshooting v1.0
No ratings yet
H30&H50 Troubleshooting v1.0
20 pages
TI 2018 - 01 Software Version 9.1A (EN)
100% (3)
TI 2018 - 01 Software Version 9.1A (EN)
50 pages
Fresenius MultiFiltrate - Service Manual
No ratings yet
Fresenius MultiFiltrate - Service Manual
150 pages
Table of Content
No ratings yet
Table of Content
120 pages
Complete Error Code - Service Logging List For Ak95 3 - 10
No ratings yet
Complete Error Code - Service Logging List For Ak95 3 - 10
130 pages
Ak 58 PDF
No ratings yet
Ak 58 PDF
58 pages
Gambro Error Code
No ratings yet
Gambro Error Code
289 pages
Ak95 34
No ratings yet
Ak95 34
3 pages
C CC 002, Preset Variable Storage
No ratings yet
C CC 002, Preset Variable Storage
2 pages
C CB 008, Blood Volume
No ratings yet
C CB 008, Blood Volume
1 page
C CB 003, Venous Pressure
No ratings yet
C CB 003, Venous Pressure
1 page
Ak96 1112 Page PDF
No ratings yet
Ak96 1112 Page PDF
2 pages
DES-00280 - Software Error Code List
No ratings yet
DES-00280 - Software Error Code List
9 pages
Hydrafacial MD Elite
No ratings yet
Hydrafacial MD Elite
20 pages
PantOs DG Plus Eng
No ratings yet
PantOs DG Plus Eng
8 pages
Rayos X Odont Preva PDF
No ratings yet
Rayos X Odont Preva PDF
135 pages
Remotion 3 SVC Manual
No ratings yet
Remotion 3 SVC Manual
23 pages
DCARE Series Dental Autoclave: Operation Manual
No ratings yet
DCARE Series Dental Autoclave: Operation Manual
14 pages
Instructions For Use: Ulthera System
No ratings yet
Instructions For Use: Ulthera System
64 pages
Manual de Usuario Microscopio Carl-Zeiss Opmi-Pico Orl
100% (3)
Manual de Usuario Microscopio Carl-Zeiss Opmi-Pico Orl
278 pages
SONOACE R5 v1.02.00 Vol1 E
No ratings yet
SONOACE R5 v1.02.00 Vol1 E
172 pages
Dfs-Manual-2 13 15
No ratings yet
Dfs-Manual-2 13 15
37 pages
SPV DS
No ratings yet
SPV DS
2 pages
Presets Parameters 12.20
No ratings yet
Presets Parameters 12.20
25 pages
Space Charge Limited Current-Voltage Characteristics of Organic Semiconductor Diode Fabricated at Various Gravity Conditions
No ratings yet
Space Charge Limited Current-Voltage Characteristics of Organic Semiconductor Diode Fabricated at Various Gravity Conditions
4 pages
Assignment1 PDF
No ratings yet
Assignment1 PDF
2 pages
Pxe Uefi Manual
No ratings yet
Pxe Uefi Manual
16 pages
MV Cable Test Report
No ratings yet
MV Cable Test Report
3 pages
Upmdt 1 Pa
No ratings yet
Upmdt 1 Pa
24 pages
60990206
No ratings yet
60990206
15 pages
Evolution of Wireless Communication PDF
No ratings yet
Evolution of Wireless Communication PDF
2 pages
Alternator
No ratings yet
Alternator
3 pages
Co2 S7
No ratings yet
Co2 S7
13 pages
Cupl Err
No ratings yet
Cupl Err
15 pages
Chapter 10 Diode
No ratings yet
Chapter 10 Diode
20 pages
Siemens-SITRANS-FUP1010 - 2 PDF
No ratings yet
Siemens-SITRANS-FUP1010 - 2 PDF
46 pages
MCE102B Automotive Controller Technical Information Manual - 53386160
No ratings yet
MCE102B Automotive Controller Technical Information Manual - 53386160
8 pages
Chap 1, 2, 3,4,5,6,7
No ratings yet
Chap 1, 2, 3,4,5,6,7
76 pages
Alarm System - Educational Example Using The Omron PLC C28K
100% (7)
Alarm System - Educational Example Using The Omron PLC C28K
6 pages
Epson Stylus Scan 2500 Service Manual
No ratings yet
Epson Stylus Scan 2500 Service Manual
178 pages
08 - 3al 42451 Aaaa Jcaaa
No ratings yet
08 - 3al 42451 Aaaa Jcaaa
128 pages
Network Interface Card
No ratings yet
Network Interface Card
2 pages
Unidrive M Frame 5 and 6 Installation Guide English Issue6 (0478-0255-06) - Approved - New
No ratings yet
Unidrive M Frame 5 and 6 Installation Guide English Issue6 (0478-0255-06) - Approved - New
108 pages
Computer Science 501
No ratings yet
Computer Science 501
2 pages
CMT Spot Welding
No ratings yet
CMT Spot Welding
11 pages
Schneider Electric PowerLogic-T300 EMS58581
No ratings yet
Schneider Electric PowerLogic-T300 EMS58581
3 pages
Technical Report: ON 33KV/11KV Receiving Station
100% (1)
Technical Report: ON 33KV/11KV Receiving Station
30 pages
Antennes 8 GHZ RFS
No ratings yet
Antennes 8 GHZ RFS
1 page
r14 20 en
No ratings yet
r14 20 en
6 pages
Ece Law Report
No ratings yet
Ece Law Report
6 pages