Scribd
Upload
57 views2 pages

MIC18 B.tech Model Paper-1

This document is a question paper for a Metrology and Measurements exam consisting of two parts. Part A contains 5 short answer questions worth 2 marks each. Part B contains 5 long answer questions worth 12 marks each, with each question covering a different unit of the course. The questions assess a range of metrology topics including standards of measurement, vernier instruments, interferometry, coordinate measuring machines, screw thread measurement methods, transducers, and temperature and pressure measurement techniques. Students are required to answer all questions in the paper within the allotted time of 3 hours.

Uploaded by

DNKWNDKNWKD
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
57 views2 pages

MIC18 B.tech Model Paper-1

This document is a question paper for a Metrology and Measurements exam consisting of two parts. Part A contains 5 short answer questions worth 2 marks each. Part B contains 5 long answer questions worth 12 marks each, with each question covering a different unit of the course. The questions assess a range of metrology topics including standards of measurement, vernier instruments, interferometry, coordinate measuring machines, screw thread measurement methods, transducers, and temperature and pressure measurement techniques. Students are required to answer all questions in the paper within the allotted time of 3 hours.

Uploaded by

DNKWNDKNWKD
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Sub Code: 18ME6T03 MIC18

B. Tech VI Semester Regular Examinations


METROLOGY AND MEASUREMENTS
(Model Paper-I)
Time: 3 hours Max Marks: 70M
----------------------------------------------------------------------------------------------
Note: 1. Question paper consists of two parts (Part A and Part B)
2. Answer all sub questions from Part A
3. Answer all questions from Part B with either or choice

PART – A 5 X 2 = 10 M
I. a) Define the terms limits and tolerances 2M
b) Differentiate between Sine bar & Sine center 2M
c) List out the elements of screw thread 2M
d) What are various types of electric strain gauges? 2M
e) Explain the principle of thermo couple in temperature 2M
measurement
PART – B 5 X 12 = 60 M
UNIT - I
1 a) Differentiate between Line Standard and End Standard of 6M
measurement. Bring out suitable examples under each
category.
b) Explain the construction and applications of vernier bevel 6M
protractor.
(OR)
2. a) Explain how the flatness and parallelism of the two faces of 6M
slip gauge can be tested with the help of any method based on
the principle of interference of light.
b) Determine and sketch the limits of tolerance and allowance for 6M
a 42 mm shaft and hole pair designated as H 8 - g10. The
basic size lies in the range of 30 – 50 mm. The multipliers for
grades 8 and 10 are 25 and 64 respectively. The fundamental
deviation for g shaft is (- 2.5 D0.34) microns. The standard
tolerance unit is i = 0.45 (D) 1/3+ 0.001D in microns.
UNIT - II
3. a) Explain NPL flatness interferometer with neat sketch and write 6M
its applications
b) Explain Talysurf with a neat sketch 6M

Page 1 of 2
(OR)
4. a) Explain the use of optical flat for the measurement of convex 6M
and concave surfaces with fringe patterns.
b) Explain different types of coordinate measuring machines with 6M
sketches
UNIT - III
5. a) What are various errors in the screw thread? explain 6M
b) Explain constant chord method in gear measurements 6M
(OR)
6. a) Explain one-wire, two-wire and three-wire methods 6M
b) Explain Base tangent method in gear measurements 6M
UNIT - IV
7. a) What are transducers and how they are classified? Explain any 6M
one transducer with neat diagram.
b) What are contact less electrical tachometers? Explain the 6M
working of any one with neat sketch
(OR)
8. a) Explain the piezo electric transducer 6M
b) Explain the method of measuring strain by using strain gauges 6M
UNIT - V
9. a) What are load cells? explain 6M
b) Explain the method of measuring torque by using a torsion bar 6M
dynamometer
(OR)
10. a) Define thermocouple. List its advantages and disadvantages. 6M
b) Explain dead weight gauge and manometers 6M

***End of Question Paper***

Page 2 of 2

You might also like