Scribd
Upload
48 views16 pages

Academic Year: 2020 - 2021 (Odd Semester) : 1917101-Advanced Concrete and Steel Structures

The document outlines the units of study for the course "Advanced Concrete and Steel Structures". The 5 units cover: 1) design philosophy according to Indian codes and comparisons to Eurocode and ACI codes, 2) design of special reinforced concrete elements like slender columns and walls, 3) flat slab and plate design using yield line theory, 4) design of welded and bolted connections, and 5) design of light gauge steel structures using direct strength method.

Uploaded by

SuganthanSelvam
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
48 views16 pages

Academic Year: 2020 - 2021 (Odd Semester) : 1917101-Advanced Concrete and Steel Structures

The document outlines the units of study for the course "Advanced Concrete and Steel Structures". The 5 units cover: 1) design philosophy according to Indian codes and comparisons to Eurocode and ACI codes, 2) design of special reinforced concrete elements like slender columns and walls, 3) flat slab and plate design using yield line theory, 4) design of welded and bolted connections, and 5) design of light gauge steel structures using direct strength method.

Uploaded by

SuganthanSelvam
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 16

SRM VALLIAMMAI ENGINEERING COLLEGE

(AN AUTONOMOUS INSTITUTION)


DEPARTMENT OF CIVIL ENGINEERING
ME STRUCTURAL ENGINEERING

Academic Year : 2020 - 2021 (Odd Semester)

First semester

1917101-ADVANCED CONCRETE AND STEEL


STRUCTURES

Mr.S.Suresh Babu.M.Tech.,
ASSISTANT PROFESSOR (Sr.G)
UNIT-I: DESIGN PHILOSOPHY
Limit state design - beams, slabs and columns according to IS Codes.
Calculation of deflection and crack width according to IS Code. Interaction
curve generation for axial force and bending. Comparative study with Euro
Code & ACI Code.

UNIT-II: SPECIAL RC ELEMENTS


Design of slender columns - Design of RC walls. Strut and tie method of
analysis for corbels and deep beams, Design of corbels, Deep-beams and
grid floors, Pile caps.

UNIT-III: FLAT SLABS AND YIELD LINE BASED DESIGN


Design of flat slabs and flat plates according to IS method – Check for
shear - Design of spandrel beams - Yield line theory and Hillerborg’s strip
method of design of slabs. Yield line theory - Equilibrium and Virtual work
method - Analysis and design of square slab with different boundary
conditions subjected to UDL and concentrated loads – Analysis and design
of rectangular slab with different boundary conditions subjected to UDL
and concentrated loads.
UNIT-IV: DESIGN OF CONNECTIONS
Types of connections – Welded and Bolted – Throat and Root Stresses in
Fillet Welds – Seated Connections – Unstiffened and Stiffened seated
Connections – Moment Resistant Connections - Clip angle Connections –
Split beam Connections – Framed Connections HSFG bolted connections.

UNIT-V: DESIGN OF LIGHT GAUGE STEEL STRUCTURES


Introduction to Direct Strength Method - Behaviour of Compression
Elements - Effective width for load and deflection determination –
Behaviour of Unstiffened and Stiffened Elements – Design of webs of
beams – Flexural members – Lateral buckling of beams – Shear Lag –
Flange Curling – Design of Compression Members – Wall Studs.
UNIT-I
DESIGN PHILOSOPHY
CONTENT

• Limit state design

• Beams, slabs and columns according to IS Codes.

• Calculation of deflection and crack width according to

IS Code.

• Interaction curve generation for axial force and bending.

• Comparative study with Euro Code & ACI Code


Scanned with
CamScanner
Scanned with
CamScanner
Scanned with
CamScanner
Scanned with
CamScanner
Scanned with
CamScanner
Scanned with
CamScanner
Scanned with
CamScanner

You might also like