DLC Display Co.

, Limited

德爾西顯示器有限公司

MODEL No:DLC0350AMG-T-4

TEL: 86-755-86029824

FAX: 86-755-86029827

E-MAIL: sales@dlcdisplay.com

WEB: www.dlcdisplay.com
 Module Name: DLC0350AMG-T-4 Ver1.0
.

Record of Revision

Date Revision No. Summary

2011-04-19 1.0 Rev 1.0 was issued

http://www.dlcdisplay.com Email:sales@dlcdisplay.com
Page 2 of 18
 Module Name: DLC0350AMG-T-4 Ver1.0

1. Scope
This data sheet is to introduce the specification of DLC00350AMG-T-4, active matrix TFT module.
It is composed of a color TFT-LCD panel, driver ICs, FPC ,touch panel and a backlight unit. The
3.5′′ display area contains 320(RGB) x 240 pixels.

2. Application
Digital equipments which need color display, mobile phone, mobile navigator/video systems.

3. General Information

Item Contents Unit

Size 3.5 inch

Resolution 320(RGB) x 240 /

Technology type a-si TFT /

Interface RGB

Pixel pitch 0.219x0.219 mm

Pixel Configuration R.G.B. Vertical Stripe

Outline Dimension (W x H x D) 76.9 x 64.0 x 4.25 mm

Active Area 70.08 x 52.56 mm

Transmissive
Display Mode /
Normally White
/
Backlight Type LED

http://www.dlcdisplay.com Email:sales@dlcdisplay.com
Page 3 of 18
 Module Name: DLC0350AMG-T-4 Ver1.0

4. Outline Drawing

http://www.dlcdisplay.com Email:sales@dlcdisplay.com
Page 4 of 18
 Module Name: DLC0350AMG-T-4 Ver1.0
5. Interface signals
Pin No. Symbol Description

1,2 VBL- Backlight LED Cathode

3,4 VBL+ Backlight LED Anode.

5~7 NC NC

8 RESET Reset Signal pin (“Low” is enable)

9 CS Chip select

10 SCL Serial Clock.

11 SDI Serial Data

12~19 B0~B7 Data bus

20~27 G0~G7 Data bus

28~35 R0~R7 Data bus

36 HSYNC Line Synchronous Signal

37 VSYNC Frame Synchronous Signal

38 DOTCLK Dot-clock signal and oscillator source

39~40 NC NC

41~42 VCC Power supply for logic operation

43~47 NC NC

48 NC NC

49 NC NC

50 NC NC

51 NC NC

52 DEN Display enable signal

53~54 GND System Ground

http://www.dlcdisplay.com Email:sales@dlcdisplay.com
Page 5 of 18
 Module Name: DLC0350AMG-T-4 Ver1.0
6. Absolute maximum Ratings
6.1. Electrical Absolute max. ratings

Item Symbol MIN MAX Unit Remark

Power Supply Voltage VDD -0.3 5.0 V

6.2. Environment Conditions

Item Symbol MIN MAX Unit Remark

Operating Temperature TOPR -20 +70 ℃

Storage Temperature TSTG -30 +80 ℃

6.3. LED Backlight Absolute max. ratings

Item Symbol MIN MAX Unit Remark

LED Forward Current ILED -- 25 mA For each LED

http://www.dlcdisplay.com Email:sales@dlcdisplay.com
Page 6 of 18
 Module Name: DLC0350AMG-T-4 Ver1.0

7. Electrical Specifications
7.1 Electrical characteristics

Item Symbol MIN TYP MAX Unit Remark

Supply Voltage VDD 3.0 3.3 3.6 V

Low
VIL GND - 0.1x VDD V
Level
Input Signal Voltage
High
VIH 0.8x VDD - VDD V
Level

7.2 LED Backlight Ta=25℃

Item Symbol MIN TYP MAX Unit Remark

Forward Current IF -- 20 25 mA
Forward Current Voltage VF 16.8 19.2 21.6 V
Backlight Power Consumption WBL -- 384 -- mW

The figure below shows the connection of LED

http://www.dlcdisplay.com Email:sales@dlcdisplay.com
Page 7 of 18
 Module Name: DLC0350AMG-T-4 Ver1.0
7.3 Block Diagram

http://www.dlcdisplay.com Email:sales@dlcdisplay.com
Page 8 of 18
 Module Name: DLC0350AMG-T-4 Ver1.0

8. Command/AC Timing
8.1 AC Electrical Characteritics

8.2 24 Bit RGB Mode (@ SEL\[3:0] = 1100 or 1101)

http://www.dlcdisplay.com Email:sales@dlcdisplay.com
Page 9 of 18
 Module Name: DLC0350AMG-T-4 Ver1.0

8.3 Timing Diagram

http://www.dlcdisplay.com Email:sales@dlcdisplay.com
Page 10 of 18
 Module Name: DLC0350AMG-T-4 Ver1.0

8.4 Vertical Timing Diagram (HV Mode)

8.5 Vertical Timing Diagram (DE Mode)

http://www.dlcdisplay.com Email:sales@dlcdisplay.com
Page 11 of 18
 Module Name: DLC0350AMG-T-4 Ver1.0

8.6 Input Data Timing (24 bit RGB mode for 960 x 240 @ SEL\[3:0] = 1100b)

http://www.dlcdisplay.com Email:sales@dlcdisplay.com
Page 12 of 18
 Module Name: DLC0350AMG-T-4 Ver1.0
9. Optical Specification
Ta=25℃
Item Symbol Condition Min Typ. Max. Unit Remark

Note1
Contrast Ratio CR θ=0° - 350 -
Note2
Note1
Response Time Ton/ Toff 25℃ - 25 40 ms
Note3
ΘT 30 40 -

ΘB 50 60 -
View Angles CR≧10 Degree Note 4
ΘL 50 60 -

θR 50 60 -

x 0.636
Red
y 0.350

x 0.311
Green
y Brightness 0.551 Note5,
Chromaticity Typ-0.05 Typ+0.05
x is on 0.134 Note1
Blue
y 0.151

x 0.311
White
y 0.353

NTSC S 50 % Note 5
Note1
Luminance L 440 480 - cd/m2
Note6
Note1
Uniformity U 75 80 - %
Note7

http://www.dlcdisplay.com Email:sales@dlcdisplay.com
Page 13 of 18
 Module Name: DLC0350AMG-T-4 Ver1.0
Note 1: Definition of optical measurement system.
Temperature = 25℃(±3℃)
LED back-light: ON, Environment brightness < 150 lx

Note 2: Contrast ratio is defined as follow:

Surface Luminance with all white pixels
Contrast Ratio = Surface Luminance with all black pixels

Note 3: Response time is defined as follow:

Response time is the time required for the display to transition from black to white (Rise Time, Tr) and from
white to black(Decay Time, Tf).

http://www.dlcdisplay.com Email:sales@dlcdisplay.com
Page 14 of 18
 Module Name: DLC0350AMG-T-4 Ver1.0
Note 4: Viewing angle range is defined as follow:
Viewing angle is measured at the center point of the LCD.

Note 5: Color chromaticity is defined as follow: (CIE1931)

Color coordinates measured at center point of LCD.

area of RGB triangle

S  100%
area of NTSC triangle

http://www.dlcdisplay.com Email:sales@dlcdisplay.com
Page 15 of 18
 Module Name: DLC0350AMG-T-4 Ver1.0

Note 6: Luminance is defined as follow:

Luminance is defined as the brightness of all pixels “White” at the center of display area on optimum contrast.

Note 7: Luminance Uniformity is defined as follow:

Active area is divided into 9 measuring areas (Refer Fig. 2). Every measuring point is placed at the center
of each measuring area.
Minimum Luminance(brightness) in 9 points
Uniformity(U) = Maximum Luminance(brightness) in 9 points

Fig. 2 Definition of uniformity

http://www.dlcdisplay.com Email:sales@dlcdisplay.com
Page 16 of 18
 Module Name: DLC0350AMG-T-4 Ver1.0

10. Environmental / Reliability Tests

No Test Item Condition Judgment criteria
1 High Temp Operation Ts=+70℃, 120hrs Per table in below

2 Low Temp Operation Ta=-20℃, 120hrs Per table in below

3 High Temp Storage Ta=+80℃, 120hrs Per table in below

4 Low Temp Storage Ta=-30℃, 120hrs Per table in below

Per table in below
High Temp & High Ta=+60℃, 90% RH
5 (polarizer discoloration is
Humidity Storage 120 hours
excluded)
Thermal Shock -30℃ 30 min~+80℃ 30 min,
6 Per table in below
(Non-operation) Change time:5min, 10 Cycles

C=150pF, R=330Ω，5points/panel
7 ESD (Operation) Air:±8KV, 5times; Per table in below
Contact:±4KV, 5 times;

Frequency range:10~55Hz,
Vibration Stroke:1.5mm
8 Per table in below
(Non-operation) Sweep:10Hz~55Hz~10Hz 2 hours
for each direction of X.Y.Z.
Shock 60G 6ms, ±X,±Y,±Z 3times,
9 Per table in below
(Non-operation) for each direction
Package Height:80 cm,
10 Per table in below
Drop Test 1 corner, 3 edges, 6 surfaces

INSPECTION CRITERION(after test)

Appearance No Crack on the FPC, on the LCD Panel
Alignment of LCD Panel No Bubbles in the LCD Panel
No other Defects of Alignment in Active area
Electrical current Within device specifications
Function / Display No Broken Circuit, No Short Circuit or No Black line
No Other Defects of Display

http://www.dlcdisplay.com Email:sales@dlcdisplay.com
Page 17 of 18
 Module Name: DLC0350AMG-T-4 Ver1.0
11. Precautions for Use of LCD Modules
11.1 Safety
The liquid crystal in the LCD is poisonous. Do not put it in your mouth. If the liquid crystal touches your skin or
clothes, wash it off immediately using soap and water.
11.2 Handling
A. The LCD and touch panel is made of plate glass. Do not subject the panel to mechanical shock
or to excessive force on its surface.
B. Do not handle the product by holding the flexible pattern portion in order to assure the
reliability
C. Transparency is an important factor for the touch panel. Please wear clear finger sacks, gloves
and mask to protect the touch panel from finger print or stain and also hold the portion
outside the view area when handling the touch panel.
D. Provide a space so that the panel does not come into contact with other components.
E. To protect the product from external force, put a covering lens (acrylic board or similar board)
and keep an appropriate gap between them.
F. Transparent electrodes may be disconnected if the panel is used under environmental
conditions where dew condensation occurs.
G. Property of semiconductor devices may be affected when they are exposed to light, possibly
resulting in IC malfunctions.
H. To prevent such IC malfunctions, your design and mounting layout shall be done in the way
that the IC is not exposed to light in actual use.
11.3 Static Electricity
A. Ground soldering iron tips, tools and testers when they are in operation.
B. Ground your body when handling the products.
C. Power on the LCD module before applying the voltage to the input terminals.
D. Do not apply voltage which exceeds the absolute maximum rating.
E. Store the products in an anti-electrostatic bag or container.
11.4Storage
A. Store the products in a dark place at +25℃±10℃ with low humidity (40% RH to 60% RH).
Don't expose to sunlight or fluorescent light.
B. Storage in a clean environment, free from dust, active gas, and solvent.
11.5 Cleaning
A. Do not wipe the touch panel with dry cloth, as it may cause scratch.
B. Wipe off the stain on the product by using soft cloth moistened with ethanol. Do not allow
ethanol to get in between the upper film and the bottom glass. It may cause peeling issue or
defective operation. Do not use any organic solvent or detergent other than ethanol.
11.6 Cautions for installing and assembling
Bezel edge must be positioned in the area between the Active area and View area. The
bezel may press the touch screen and cause activation if the edge touches the active area.
A gap of approximately 0.5mm is needed between the bezel and the top electrode. It may
cause unexpected activation if the gap is too narrow. There is a tolerance of 0.2 to 0.3mm
for the outside dimensions of the touch panel and tail. A gap must be made to absorb the
tolerance in the case and connector.

http://www.dlcdisplay.com Email:sales@dlcdisplay.com
Page 18 of 18