Scribd
Upload
53 views6 pages

8050 Microprocessor Assembly Program

The program multiplies two 8-bit numbers stored in memory locations 8000H and 8001H using the successive addition method. It initializes registers, loads the operands, clears the result registers to zero, and then loops 8 times rotating and adding the multiplied value to the result. After decrementing the loop counter, it stores the final 16-bit result in memory locations 8050H and 8051H.

Uploaded by

Diksha Suman
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
53 views6 pages

8050 Microprocessor Assembly Program

The program multiplies two 8-bit numbers stored in memory locations 8000H and 8001H using the successive addition method. It initializes registers, loads the operands, clears the result registers to zero, and then loops 8 times rotating and adding the multiplied value to the result. After decrementing the loop counter, it stores the final 16-bit result in memory locations 8050H and 8051H.

Uploaded by

Diksha Suman
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

MICROPROCESSOR & MICROCONTROLLER LAB

NAME: PRITHWISH CHATERJEE

SEC: B ROLL: 59

UNIVERSITY ROLL : 10900318068

ELECTRONICS AND COMMUNICATION


ENGINEERING
2. Write an assembly language programme to substract two data stored in memory location

9801 H and 9801H. Store the result in 9802 .If borrow is generated store it in 9803 H.

Address HEX Codes Labels Mnemonics Comments

9000 0E, 00 MVI C,00H Clear C register

9002 21, 00, 80 LXI H,9801H Load initial address to get operand

9005 7E MOV A,M Load Acc with memory element

9006 23 INX H Point to next location

9007 46 MOV B, M Load B with second operand

9008 90 SUB B Subtract B from A

9009 D2, 0D, F0 JNC STORE When CY = 0, go to STORE

900C 0C INR C Increase C by 1

900D 21, 50, 80 STORE LXI H,9802H Load the destination address

9010 77 MOV M, A Store the result

9011 23 INX H Point to next location

9012 71 MOV M, C Store the borrow

9013 76 HLT Terminate the program


first INPUT

Address Data

8000 78

8001 5D

first OUTPUT

Address Data

8050 1B

8051 00

second INPUT

Address Data

8000 23

8001 CF

second output

Address Data

8050 54

8051 01
FLOWCHART :-
2. Write an assembly language programme to multiply two 8 bit data using successive additive

method.

Address HEX Codes Labels Mnemonics Comments

F000 21, 00, 80 LXI H,8000H Point to first operand

F003 5E MOV E,M Load the first operand to E

F004 16, 00 MVI D,00H Clear the register D

F006 23 INX H Point to next location

F007 7E MOV A,M Get the next operand

F008 0E, 08 MVI C,08H Initialize counter with 08H

F00A 21, 00, 00 LXI H, 0000H Clear the HL pair

F00D 0F LOOP RRC Rotate the acc content to right

F00E D2, 12, F0 JNC SKIP If carry flag is 0, jump to skip

F011 19 DAD D Add DE with HL

F012 EB SKIP XCHG Exchange DE and HL

F013 29 DAD H Add HL with HL itself

F014 EB XCHG Exchange again the contents of DE and


HL

F015 0D DCR C Decrease C register

F016 C2, 0D, F0 JNZ LOOP if Z = 0, jump to LOOP

F019 22, 50, 80 SHLD 8050H Store the result

F01C 76 HLT Terminate the program


Input:

Address Data

8000 25

8001 2A

Output:

Address Data

8050 12

8051 06

PTO
FLOWCHART :-

You might also like