Body Control Module Body Systems

Body Control Module

Specifications
Torque
Description Value
Bolt - Body Control Module to Instrument Panel 6-8 Nm
Crossmember

cardiagn.com

V 2.0 611
Body Systems Body Control Module

Description and Operation

System Component Layout

cardiagn.com
1. Body Control Module 2. Diagnostic Socket

V 2.0 612
Body Control Module Body Systems
System Control Diagram

cardiagn.com
A = High Speed CAN Bus Line; B = K Line
1. Automatic Air Conditioning Control Unit 5. ABS/DSC Control Module
2. Diagnostic Socket 6. Supplementary Restraint System Control Module
3. Engine Control Module 7. Instrument Pack
4. Automatic Transmission Control Module 8. Body Control Module

V 2.0 613
Body Systems Body Control Module

Description BCM stores the maintenance interval data displayed on

BCM is located behind the driver side instrument panel.BCM the instrument pack.
is in charge of most control functions of the vehicle, and • Diagnostic Code
interacts with the other main electrical systems through the
When the ignition switch is on,BCM performs the
high speedCAN bus line, and interacts with the secondary
self-diagnosis inspection, and stores all the corresponding
electrical system through theK bus line connection.BCM is in
malfunctions detected by theEEPROM with the display
charge of the power distribution system, and supplies power
of diagnostic trouble codes. The malfunctions within the
to most of the electrical components of the vehicle.
CANCAN andK are stored simultaneously.
Through the high speedCAN bus line, the body control
Program Function
module communicates with the following components and
they interact with each other: T5 allows to perform the following functions:

• Engine Control Module (ECM) • Add a new blank key.

• Automatic Transmission Control Module (TCU) • Disable/enable an existing door key.
• Supplementary Restraint System Control Module (SRS • When replacing the BCM, obtain the security code from
ECU) EMS.
• ABS/DSC Control Module • When replacing the engine control module (ECM),
provide the security code to EMS.

cardiagn.com
• Instrument Pack (Including All Meters and Warning
Lights) • When replacingBCM andECM simultaneously, a new
security code is created.
ABS/DSC control module connects with the steering angle
• Set the battery load management state.
sensor SAS and yaw rate sensor YRS through the local high
speedCAN bus line. • Refresh the software programs (only on the premise of
the manufacturer's guidance).
Through theK bus line, the body control module
Body Control Unit Connector
communicates with the following components and they
interact with each other There are four connectors in the body control unit:
MG644114, MG644088, MG643335-R00 and MG643314,
• Automatic Air Conditioning Control Unit (ATC)
which provide signal input/output service for the body control
Besides,BCM controls the operation and information storage unit.
in the following assist systems :
BCM connector MG644114
• Battery Voltage
BCM receives the load status of the alternator.CAN will
display this status information which is used to manage
the load of the alternator.
• Vehicle Odometer
BCM stores the readings of the vehicle odometer (up
to 999999 km). The instrument pack displays the latest
maximum reading of odometer. The odometer reading
cannot be changed after it is stored.
• Vehicle Identification Number (VIN) Memory
Pin Number Description
VIN is stored in BCMand it cannot be changed after the 1 Exterior Antenna Input
preset distance is reached.VIN.
2 Start Switch Input
• Vehicle Configuration Information 3 Rear Washer Switch
BCM stores the vehicle configuration information. 4 Front Washer Switch
The vehicle configuration codes contain the vehicle 5 Reserve
construction information, including the optional
6 Reserve
components.
7 Rear Window Lifter Disable
• Maintenance Interval Display Switch

V 2.0 614
Body Control Module Body Systems
8 Rear Wiper Return Signal BCM Connector MG644088
9 Rear Wiper Switch
10 Front Wiper Pattern Select
Switch 1
11 Direction Indicator Switch RH
12 Exterior Light Switch 1
13 Reserve
14 Boot Opener Switch
15 Driver Door Open Warning Pin Number Description
Switch
1 Rear Window Disable Switch
16 Driver Door Key Lock Signal Illumination
17 Main Beam Lamp Blinking 2 Main Beam Relay Coil
Switch
3 Rear Window Heat Relay Coil
18 Data Link of IMMO SPI Bus
Line 4 Lower the Driver Window

19 Clock Line of IMMO SPI Bus 5 Starter Motor Relay Coil

Line 6 Raise the Front Passenger

cardiagn.com
20 Bonnet Open Warning Switch Window

21 ACC Switch 7 Lower the Rear Window RH

22 Ignition Switch 8 Safety Lock Relay Coil

9 Raise the Driver Window
23 Reverse Switch
24 Exterior Light Switch 2 10 Reserve Low Side Drive
Output 2
25 Reserve
11 Reserve Low Side Drive
26 Inertia Switch, Wake-up Input Output 4
27 Rear Window Heat Switch 12 Door Lock Status Indicator
28 Front Wiper Return Signal 13 Reserve Analog Input
29 Front Wiper Pattern Select 14 Wiper Interval Time Select
Switch 2 Signal
30 Emergency Warning Light 15 Front Wiper Speed Selection
Switch
16 Rear Wiper Relay Coil
31 Direction Indicator Switch LH
17 Side Light Coil
32 Reserve
18 Front Wiper Enable Relay Coil
33 Trunklid Open Warning Switch
19 Wiper Analog Quantity
34 Passenger Door Open Warning Ground
Switch
20 Lower the Rear Window LH
35 Driver Door Key Unlock Signal
21 Raise the Rear Window LH
36 Main Beam Lamp Switch
22 Raise the Rear Window RH
37 Rear Fog Lamp Switch
23 Lower the Front Passenger
38 CAN Bus Line Low Window
39 CAN Bus Line High 24 Reserve Low Side Drive
Output 1
40 Reserve
25 Reserve Low Side Drive
Output 3
26 Rear Window Heat Switch
Status Indicator

V 2.0 615
Body Systems Body Control Module

27 Inner Centre Control Lock BCM Connector MG643314

Switch
28 Sunroof Auto Close Signal

BCM Connector MG643335-R00

Pin Number Description

1 Battery Power Source
2 Dipped Beam Lamp Output
3 Door Lock Output
Pin Number Description 4 Battery Power Source
1 Direction Indicator Output RH 5 Low Current Ground
2 Rear Fog Lamp Output 6 Direction Indicator Output LH
7 Room Light PWM Output

cardiagn.com
3 Boot Unlock Output
4 Front Water Pump Output 8 Reserve
5 Battery Power Source 9 Warning Request Signal
6 Room Light Delay Relay 10 Door Unlock Output
Output 11 High Current Ground
7/8 Window Lifting Function
Enabled
9/10 Rear Window Function
Disable
11 Battery Power Source

V 2.0 616
Body Control Module Body Systems
Operation With the use of T5, the dealer can change the vehicle load
General management configuration from the transportation mode to
the normal mode.
After the ignition switch is turned off,BCM can run the
safety system, lighting system and diagnostic system. When Normal Mode
the ignition switch is in the electronicAUX (Auxiliary) Normal mode is the default setting. The vehicle is used during
position,BCM allows the washer/wiper and power window normal operation after PDI is finished.
to run simultaneously. When the ignition switch is turned to
Sleep Mode
IGN (Ignition) position, the fuel system can be operated.BCM
communicates and transfers the information withECU After turning the ignition switch off, if the battery is still
betweenCAN andK bus line. connected, andCAN andK bus line are in the disable
status,BCM will keep in the sleep mode to reduce the current
BCM can perform management configuration selective
consumption as much as possible.BCM is ready to receive
operation for a large amount of electrical load. Be sure to
theCAN andK bus line signals at all time. During the load
decrease the battery consumption when the vehicle is in
mode, it is necessary to turn off some electrical load in order
storage mode, transportation mode or the vehicle is not used
to provide maximum current for the starter motor when
for a period of time.
the power source is off and the engine is started, such as
Transportation Mode cutting off the power supply of the air conditioning blower
Configuring the transportation mode to prevent excessive motor, Heated Rear Window (HRW), front/rear fog lamp

cardiagn.com
battery consumption when the vehicle is delivered to and the main beam headlight. After the engine is started, each
the dealer after shipping from the factory. After the electrical load can be reactivated alone to limit the battery
vehicle is assembled, programme the BCMin order to current consumption. The electrical load can be reactivated
use the transportation mode during transportation. The after the following delay. If the starting time is beyond 45
transportation mode will keep until the pre-delivery inspection seconds, the starter motor will be detached, and all electrical
(PDI) is performed. The transportation mode will restrict loads will be turned on simultaneously.
some electrical functions, for example:

V 2.0 617
Body Systems Body Control Module

Service Procedures
Body Control Module (BCM)
Removal
1. Disconnect the battery earth lead.
2. Remove the driver side apron board.

Driver Side Apron Board Removal

cardiagn.com
3. Remove 2 bolts securing the body control module to
the crossmember.
4. Disconnect the electrical connector.
5. Remove the body control module.
Refit
1. Connect the electrical connector.
2. Secure the body control module to the crossmember
with 2 bolts, and tighten to 6-8 Nm.
3. Fit the driver side apron board.

Driver Side Apron Board Refit

4. Connect the battery earth lead.

V 2.0 618