说明书图纸

TPMS说明书 A
T P M S - A - O N E /英 文 中 性
400x220mm 40119200030 2020.3.14

Monitor Installation Position 3.According to the sensor location

identifier,screw on and tighten for
4.Tighten the sensor by nut wrench ④
in direction toward the sensor.
the corresponding tire.

Solar TPMS
Tire Pressure Monitor System Note:It is normal to have a little air leak at
this time, please screw it up quickly.

5.Check if it's leaking with soapsuds

or other methods.

Internal Sensor Installation

1.Remove the origin valve and 2.Lock sensor valve screw by
install the sensor sleeve.

Installation Battery Replacement

1.Before using,press the left button for 3 seconds Alarm and Function Description When the monitor shows sensor low power alarm
to turn on,then charge the monitor for 3~4 hours.
or the sensor low power icon is on, you need to
2.After the monitor is fully charged, with the monitor 4.Hand on and press the sensor
turned on, start installing and match the sensors. 3.Put the sensor on the wheels in housing,tighten the screw behind replace the sensor battery.（CR1632 3.0V battery）
order to touch well the sensor by hexagonal screw
driver
Sensor Installation Position
Introduction 1.Unscrew the nut spanner (④). 2.Unscrew and take out the sensor.

5.Don’t fit the screw too tight 6.Charge Nitrogen gas

3.Take out the locking plate. 4.Use the spanner for sensor(⑤)
to unscrew the sensor.

Left button Right button

Setting button
MAIN COMPOENTS External Sensor Installation 7.Balance tiret

1.Screw out the valve dustproof 2.Screw in the hexagonal nut ② 6.Reverse operation,the sensor
cover. 5.Replace a new battery. will be refitted.
x4 x4 x4
①External sensor ②Hexagonal nut ③Silicone gaskett
(Included in sensor,
for spare)

3.After sensor installation, if the display does not

show the corresponding data in time, please drive
④Nut spanner ⑤Spanner for sensor ⑥USB charging cable
to refresh the value(speed over 20km/h).

3.The pressure unit setting

Learning code Special requirements setting Press setting button for 3 seconds to enter into
Special Reminding Trouble Shootings
setting interface,press right button once to see
The system has been set according to the standard,
tire setting button is flashing, press the left 1.Solar automatic charging. Sensor interface leak gas
do not change any setting before using if you have
no special requirements.
button once to see high pressure setting value, 2.The system preset with alarm value,no Nozzle edge is usually caused by uneven gap.
and then press right button 3 times too see Bar Sensor lost
1.High Pressure Setting icon flashing.It means the pressure unit is Bar now.
matter air pressure over3.0Bar(43 Psi)or
under 1.8Bar(26Psi),temperature over 68C, Buy new sensors from our company,then learn the
(Notice: If see Psi icon flashing,the measurement new code for matching
unit is Psi). Press the left button once,will hear as well as quick or slow air leakage,it will
The battery runs out
a Be sound , at this moment Psi icon flashing , the alarm Please replace new Cr1632 3.0V battery by yourself
pressure unit has been changed. Press setting 3.Suggested air pressure range:2.2~2.3Bar Tire conversion processing
button twice to exit and pressure unit setting (32~34Psi)in summer and 2.4~2.6Bar
success. Such as the tire replacement position,the sensor
(35~38Psi)in winter. must identify the location of their respective houing
4.Regarding to solar charging,the charging swap.
current will change according to the intensity Notes and Statement
of sunlight. This product is only suitable for tire pressure within
5.If you don’t follow above requirements,It’s safe12V battery model vehicle;not suitable for
easy to damage the product. trucks or 4wheels vehicle with tire pressure over
6.Charging environment must be under 45C. 3.5Bar/50Psi
7.Unplug the charger when fully charged. Tire safety must not rely on this product,should
regularlycheck the tire,make sure without puncture,
4.Restore to factory setting tirecut,bulge and other damages.
In power on status,press right button or 3 seconds, External sensor battery life is related witj car’s
the monitor can restore factory setting.There is a Be.. mileage,working temperature can not exceed
sound to indicate setting success.It will automatically -20C~+70C Internal sensor working temperature
clear the previous setting value. range-40C~+100C
Note:This system can monitor effectively the
automobile wheels’tire pressure and temperature,
Data refresh Function Specification but could not prevent the occurrence of unexpected
accidents.The Company will not be liable for any
resulting from the damage of this product caused by
1.After parking,the monitor will automatically
direct or indirect losses.
go to sleep mode,and will start to work when
triggered by movement.
2.In power off status, press left button for 3
seconds to
turn on the monitor.In power on status,press
left button to turn off monitor.
2.Low pressure and high temperature 3.Start monitor in the sunlight,the monitor will
setting keep in high luminance for 30 seconds and go
Refer to high pressure setting method,repeat step 1-3, to adjustable luminance mode(press left button
continue to press left button once,then press right to choose high,middle or low luminance).
button once to enter into low pressure setting The factory setting is low luminance.If without
interface.Repeat step 1-3,continue to press right button sunlight,the monitor will automatically go to
twice to enter into high temperature setting interface. low luminance power saving mode.
4.In power on status,press right button for 3
second,the monitor can restore factory setting.
There is a Be.sound to indicate setting success.
5.When the monitor alarms,press any button to
turn off the sound.
6.In power on status,press setting button for
3 seconds to set the system parameter.

40119200030

印 刷 要 求：
材 质 ：80克 书 写 纸
尺 寸 ：400x220mm
颜色：单黑、双面印刷。
工 艺 ： 风琴折,再 横 对 折

设 计: 审核： 批准：
 Monitor Installation Position 3.According to the sensor location
identifier,screw on and tighten for
4.Tighten the sensor by nut wrench ④
in direction toward the sensor.
the corresponding tire.

Solar TPMS
Tire Pressure Monitor System Note:It is normal to have a little air leak at
this time, please screw it up quickly.

5.Check if it's leaking with soapsuds

or other methods.

Internal Sensor Installation

1.Remove the origin valve and 2.Lock sensor valve screw by
install the sensor sleeve.

Installation Battery Replacement

1.Before using,press the left button for 3 seconds Alarm and Function Description When the monitor shows sensor low power alarm
to turn on,then charge the monitor for 3~4 hours.
or the sensor low power icon is on, you need to
2.After the monitor is fully charged, with the monitor 4.Hand on and press the sensor
turned on, start installing and match the sensors. 3.Put the sensor on the wheels in housing,tighten the screw behind replace the sensor battery.（CR1632 3.0V battery）
order to touch well the sensor by hexagonal screw
driver
Sensor Installation Position
Introduction 1.Unscrew the nut spanner (④). 2.Unscrew and take out the sensor.

5.Don’t fit the screw too tight 6.Charge Nitrogen gas

3.Take out the locking plate. 4.Use the spanner for sensor(⑤)
to unscrew the sensor.

Left button Right button

Setting button
MAIN COMPOENTS External Sensor Installation 7.Balance tiret

1.Screw out the valve dustproof 2.Screw in the hexagonal nut ② 6.Reverse operation,the sensor
cover. 5.Replace a new battery. will be refitted.
x4 x4 x4
①External sensor ②Hexagonal nut ③Silicone gaskett
(Included in sensor,
for spare)

3.After sensor installation, if the display does not

show the corresponding data in time, please drive
④Nut spanner ⑤Spanner for sensor ⑥USB charging cable
to refresh the value(speed over 20km/h).
 3.The pressure unit setting
Learning code Special requirements setting Press setting button for 3 seconds to enter into
Special Reminding Trouble Shootings
setting interface,press right button once to see
The system has been set according to the standard,
tire setting button is flashing, press the left 1.Solar automatic charging. Sensor interface leak gas
do not change any setting before using if you have
no special requirements.
button once to see high pressure setting value, 2.The system preset with alarm value,no Nozzle edge is usually caused by uneven gap.
and then press right button 3 times too see Bar Sensor lost
1.High Pressure Setting icon flashing.It means the pressure unit is Bar now.
matter air pressure over3.0Bar(43 Psi)or
under 1.8Bar(26Psi),temperature over 68C, Buy new sensors from our company,then learn the
(Notice: If see Psi icon flashing,the measurement new code for matching
unit is Psi). Press the left button once,will hear as well as quick or slow air leakage,it will
The battery runs out
a Be sound , at this moment Psi icon flashing , the alarm Please replace new Cr1632 3.0V battery by yourself
pressure unit has been changed. Press setting 3.Suggested air pressure range:2.2~2.3Bar Tire conversion processing
button twice to exit and pressure unit setting (32~34Psi)in summer and 2.4~2.6Bar
success. Such as the tire replacement position,the sensor
(35~38Psi)in winter. must identify the location of their respective houing
4.Regarding to solar charging,the charging swap.
current will change according to the intensity Notes and Statement
of sunlight. This product is only suitable for tire pressure within
5.If you don’t follow above requirements,It’s safe12V battery model vehicle;not suitable for
easy to damage the product. trucks or 4wheels vehicle with tire pressure over
6.Charging environment must be under 45C. 3.5Bar/50Psi
7.Unplug the charger when fully charged. Tire safety must not rely on this product,should
regularlycheck the tire,make sure without puncture,
4.Restore to factory setting tirecut,bulge and other damages.
In power on status,press right button or 3 seconds, External sensor battery life is related witj car’s
the monitor can restore factory setting.There is a Be.. mileage,working temperature can not exceed
sound to indicate setting success.It will automatically -20C~+70C Internal sensor working temperature
clear the previous setting value. range-40C~+100C
Note:This system can monitor effectively the
automobile wheels’tire pressure and temperature,
Data refresh Function Specification but could not prevent the occurrence of unexpected
accidents.The Company will not be liable for any
resulting from the damage of this product caused by
1.After parking,the monitor will automatically
direct or indirect losses.
go to sleep mode,and will start to work when
triggered by movement.
2.In power off status, press left button for 3
seconds to
turn on the monitor.In power on status,press
left button to turn off monitor.
2.Low pressure and high temperature 3.Start monitor in the sunlight,the monitor will
setting keep in high luminance for 30 seconds and go
Refer to high pressure setting method,repeat step 1-3, to adjustable luminance mode(press left button
continue to press left button once,then press right to choose high,middle or low luminance).
button once to enter into low pressure setting The factory setting is low luminance.If without
interface.Repeat step 1-3,continue to press right button sunlight,the monitor will automatically go to
twice to enter into high temperature setting interface. low luminance power saving mode.
4.In power on status,press right button for 3
second,the monitor can restore factory setting.
There is a Be.sound to indicate setting success.
5.When the monitor alarms,press any button to
turn off the sound.
6.In power on status,press setting button for
3 seconds to set the system parameter.

40119200030