Scribd
Upload
188 views11 pages

Dimensional Analysis: Mathematical Technique Systematic Arrangement Physical Relationship

Here are the solutions to the practice problems using dimensional analysis: 7.3) Drag force on a sphere F = f(ρ, μ, D, V) F = CρD2V2 Where C is a dimensionless drag coefficient 7.4) Fan efficiency η = f(ρ, μ, ω, D, Q) η = φ(Re, Po) Where Re is the Reynolds number (Re = ρωD/μ) and Po is the power number (Po = ρQ3/μω3D5) 7.6) Resistance R = f(ρ, μ, L, V, g) R = ρL

Uploaded by

Bin Iqbal
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
188 views11 pages

Dimensional Analysis: Mathematical Technique Systematic Arrangement Physical Relationship

Here are the solutions to the practice problems using dimensional analysis: 7.3) Drag force on a sphere F = f(ρ, μ, D, V) F = CρD2V2 Where C is a dimensionless drag coefficient 7.4) Fan efficiency η = f(ρ, μ, ω, D, Q) η = φ(Re, Po) Where Re is the Reynolds number (Re = ρωD/μ) and Po is the power number (Po = ρQ3/μω3D5) 7.6) Resistance R = f(ρ, μ, L, V, g) R = ρL

Uploaded by

Bin Iqbal
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 11

Dimensional Analysis

Dimensional analysis is a mathematical technique which makes the use of the


study of the dimensions for solving several engineering problems.
Dimensional analysis helps in determining a systematic arrangement of the
variables in the physical relationship, combining dimensional variables to form
non-dimensional parameters.
Uses of Dimensional Analysis:
1. To test the dimensional homogeneity of any equation of fluid motion.
2. To derive rational formulae for a flow phenomenon.
3. To derive equations expressed in terms of non-dimensional parameters to
show the relative significance of each parameter.
4. To plan model tests and present experimental results in a systematic
manner; thus making it possible to analyze the complex fluid flow problems.
Dimensional Analysis
Advantages of Dimensional Analysis:
1. It expresses the functional relationship between the variables in
dimensionless terms.
2. In hydraulic model studies , it reduces the number of variables involved in a
physical phenomenon.
3. By proper selection of variables, the dimensionless parameters can be used
to make certain logical deductions about the problem.
4. Design curves, by the use of dimensional analysis can be developed from
experimental data or direct solution of the problem.
5. It enables getting up a theoretical equation in a simplified dimensional
form.
Dimensions: Rajput#380
Dimensional Homogeneity
Dimensional homogeneity states that, every term in an equation when
reduced to fundamental dimensions must contain identical powers of each
dimension.
Let us consider the equation,
Pressure, p = γh
Dimension of L.H.S = M𝐿−1 𝑇 −2
Dimension of R.H.S = M𝐿−2 𝑇 −2 ∗ 𝐿= M𝐿−1 𝑇 −2
Dimension of L.H.S = Dimension of R.H.S
So, equation, p = γh is dimensionally homogeneous; so it can be used in any
system of units.
Methods of Dimensional Analysis
The methods of dimensional analysis are:
1. Rayleigh’s method
2. Buckingham’s 𝜋 method
3. Bridgman’s method
4. Matrix-tensor method
5. By visual inspection of the variables involved
6. Rearrangement of differential equations.
Here, only first two methods will be dealt with.
Rayleigh’s Method
In this method, a functional relationship of some variables is expressed in the
form of an exponential equation which must be dimensionally homogeneous.
Thus, if X is a variable which depends on 𝑋1 , 𝑋2 , 𝑋3 ,……. 𝑋𝑛 ; the functional
equation can be written as:
X = f (𝑋1 , 𝑋2 , 𝑋3 ,……. 𝑋𝑛 ) ……………………………………………………………………………. (1)
In the above equation, X is a dependent variable, while 𝑋1 , 𝑋2 , 𝑋3 ,……. 𝑋𝑛 are
independent variable.
A dependent variable is the one about which information is required while
independent variables are those which govern the variation of dependent
variable.
Thus equation (1) can be written as:
X = C (𝑋1𝑎 , 𝑋2𝑏 ,𝑋3𝑐 ,…….𝑋𝑛𝑛 ) ; Where, C is a constant and a,b,c are the arbitrary
powers.
Rayleigh’s Method (Modi#842)
Let Q be the discharge passing through a small orifice of diameter d under a
constant head H. Also let, ρ be the mass density and µ be dynamic viscosity of
the fluid flowing through the orifice. The discharge Q may be assumed to
depend on these variables, d, H, ρ, µ and the gravitational acceleration g.
Find an expression for discharge Q.
Solution:
Functional relationship for Q may be written as,
Q = f (µ, ρ, d, H, g )
By exponential form, it can be written as,
Q = C (µ𝑎 ρ𝑏 d𝑐 H𝑑 g𝑒 ) ; where C is a dimensionless constant.
Substituting the proper dimensions for each variable in this exponential
equation in M-L-T system,
Rayleigh’s Method (Modi#842)
𝐿3 𝑀 𝑎 𝑀 𝑏 𝑐 𝑑 𝐿 𝑒
= ( ) ( 3) 𝐿 𝐿 ( 2)
𝑇 𝐿𝑇 𝐿 𝑇
For dimensional homogeneity, the exponents of each dimension on both sides
of equation must be identical,
For M : 0 = a+b
For L : 3 = − a−3b+c+d+e
For T : − 1 = −a −2e
Since, there are five unknowns in three equations, three of the unknowns must
be expressed in terms of other two,
b = −a
1 𝑎
e= −
2 2
5 3𝑎
c= − −d
2 2
Rayleigh’s Method (Modi#842)
So, according to, Q = C (µ𝑎 ρ𝑏 d𝑐 H𝑑 g𝑒 )
5 3𝑎 1 𝑎
𝑎 −𝑎 2 2
Q = C[µ ρ 𝑑 − − d 𝑑 2− 2
𝐻 𝑔 ]
5 1 3𝑎 𝑎
𝑎 −𝑎 −2 −2
Q = C[(𝑑 𝑔 )
2 2 (µ ρ 𝑑 𝑔 ) (𝐻 𝑑 𝑑 −𝑑 )]
1 1
2 µ 𝑎 𝐻 𝑑
Q= C[(𝑑 𝑑 𝑔 ) ( 3 1 ) ( ) ]
2 2
𝑑
ρ𝑑 2 𝑔2
1 1 1
µ 𝐻 𝑑−
Q= C[( 3 1 )𝑎 ( ) 2 (𝑑2 𝐻 2 𝑔2 )]
𝑑
ρ𝑑 2 𝑔2
1
𝐶 µ 𝑎 𝐻 𝑑− 𝜋 2
Q= 𝜋 [( 3 1 ) ( ) 2 𝑑 2𝑔𝐻]
2 𝑑 4
4 ρ𝑑 2 𝑔2
µ 𝐻
Q= a 2𝑔𝐻𝑓1 [ 3 1 , ]
𝑑
ρ𝑑 2 𝑔2
Rayleigh’s Method (Modi#842)
This expression may be written in usual form:
Q = 𝐶𝑑 ∗ 𝑎 2𝑔𝐻
Where, 𝐶𝑑 is the co-efficient of discharge of the orifice which can be
expressed as:
µ 𝐻
𝐶𝑑 = 𝑓1 [ 3 1 , ]
𝑑
ρ𝑑 2 𝑔2
It may be pointed out that both the terms in the bracket are dimensionless
and 𝐶𝑑 is also a non-dimensional factor.
Practice Problem: Rajput#383
7.3 Find an expression for the drag force on smooth sphere of diameter D,
moving with a uniform velocity V in a fluid density ρ and dynamic viscosity µ.
7.4 The efficiency ɳ of a fan depends on the density ρ, the dynamic viscosity µ
of the fluid, angular velocity ω, diameter D of the rotor and discharge Q.
Express efficiency ɳ in terms of dimensionless parameter.
7.6 A partially submerged body is towed in water. The resistance R to its
motion depends on the density ρ, the viscosity µ of water, length L of the
body, velocity V of the body and acceleration due to gravity. Show that
resistance to motion can be expressed in the form:
µ 𝐿𝑔
R=ρ 𝐿2 𝑉 2 ɸ [( ), ( 2 )]
ρ𝐿𝑉 𝑉

You might also like