JDY-08

User Manual

Product Name: Bluetooth module

Brand: HTYD

Model: JDY-08

Manufacture: Shenzhen City Hong Teng Yu Da Electronic

Technology Co. Ltd.
JDY-08

Product Overview
The JDY-08 Bluetooth module is based on Bluetooth 4 standard, the working frequency is
2.4GHZ, the modulation mode is GFSK, the maximum transmission power of 0dB,
maximum transmission distance of 60 meters, using TICC2541 chip, support the user
through the AT command to change the device name, service UUID, transmitting power,
pairing password and other commands, convenient and flexible.

Function Brief
1: WeChat pass (support AirSync protocol, applied to WeChat H5 or manufacturer server
communication)
2:APP transparent transmission (support for Android and IOS data transmission)
3:iBeacon mode (support for WeChat shake up protocol and apple iBeacon protocol)
4: sensor mode (temperature, humidity and many other sensors, data acquisition
applications)
5: host pass mode (application data transmission between modules, host and slave
communication)
6: host Viewer Mode (Applied sensors, indoor positioning)
7:PWM mode (used in motor speed control, LED light brightness adjustment)
8:IO mode (used for mobile control relay or LED lights out)
9: indoor location applications (the application of data acquisition iBeacon to achieve
range positioning)
10:RTC function
11: supports LED light products (with 26 fixed modes, with custom mode, and panel
mode), and how it works
Optional jump, gradient, strobe.
12: support massage products, the default comes with massage methods, there are warm
massage, comfortable massage, pulse massage and so on
13: support iBeacon probe function
14: support RTC timing function
JDY-08

Electrical characteristics
Working model state Electric current
Slave Connection / connection 0.8mA/300uA/1uA
transmission / standby
model
Slave broadcast Connection / connection 0.5mA/300uA/1uA
mode / standby
IBeacon sensor
Host Connection / connection 8mA/8.5mA/1uA
transmission / standby
model
Host observer Connection / connection 9mA
mode / standby
(sensor)
The test power supply voltage is 3.3V

technical parameter
1: through the transmission, the serial port to write data, support hundreds of bytes of
writing (such as 512 bytes)
Serial port Potter 115200, the serial port supports 712 bytes (Byte) write
57600, the serial port supports 712 byte (Byte) write
38400, the serial port supports 800 byte (Byte) write
19200, support 900 byte serial (Byte) write
9600, the serial port supports 3K byte (Byte) writing
2: effective communication distance 15 to 30 meters
3: working temperature -40 ~ +80 degrees centigrade
JDY-08
Low power settings hint (enter sleep AT+SLEEP, wake on the falling edge of the
PWRC pin)
Broadcast mode power saving scheme
Broadcast shallow sleep: serial port to send AT+SLEEP or AT+SLEEP1, the current
can be set to lower through broadcast intervals
Deep sleep: serial send AT+SLEEP2, at this time the current in a few uA, this mode
is not broadcast
Connection mode power saving scheme
1: connection state needs low power consumption, the P01 pin is held low, AT
AT+SLEEP or AT+SLEEP1 command module into MCU to make sleep, when the
data will be P01 pulled high by the falling edge of the PWRC pin wake Bluetooth, so
you can ensure that the case in connection to the Bluetooth power consumption is
very low,
2: of course, you can also let the Bluetooth module and the user's MCU has been
sleeping, through the Bluetooth module to wake up the user's MCU, this way to do
more than 1 of the way to save power.
3: to reduce power consumption by setting the connection interval, this mode is
configured to save power by 1 and 2

Dimensionaldrawing
JDY-08

Pin definition

Pin function description

Pin Definition function description
1 VCC Power Supply The power supply is 3V or 3.3 volts
2 P22
3 P21
4 P20
5 P17 RTC timed RTC is high when it is turned on and the
interrupt time is low
Only when the timing value is clear will
it become high level
6 P16 Connection status The connection is high and is not
pin connected to the low level (valid)
This is the default setting
The user can set the connection status of
the P16 pin or the pulse output and data
delay through the AT command
The user needs to wake up the user MCU
via the P16 pin, and then send the data
back to the user MCU, which can be set by
the AT command
For more details, please read the
AT+REVERSE instruction function
JDY-08
7 P11 PWM2 The PWM2 output pin can be controlled by
the APP
8 P12 IO1 The output IO1 pin can be controlled level
via the APP
9 P13 IO2 The output IO2 pin can be controlled level
via the APP
10 P15 IO3 The output IO3 pin can be controlled level
via the APP
11 SCK The JDY-08D version supports IIC
Communications
12 SDA The JDY-08D version supports IIC
Communications
13 P14 IO4 The output IO4 pin can be controlled level
via the APP
14 P10 PWM1 The PWM1 output pin can be controlled by
the APP
15 P07 PWM3 The PWM3 output pin can be controlled by
the APP
16 P06 PWM4 The PWM4 output pin can be controlled by
the APP
17 P05 Broadcast status Broadcast flashing, often bright after the
pin connection (master-slave effective)
18 P04
19 P03 TXD Serial output, the level is TTL level
20 P02 RXD Serial port, level is TTL level
21 P01 AT instruction Low level AT mode with default high
control pin level
This pin does not need to be sent AT if it
is connected
When the AT instruction in the state of
the connection request, the P01
pin is held low, in AT mode, the
user can then send the AT
command, to pass through the
data when P01 will maintain a
high level, immediately into
transmission mode
Is it necessary to send P01 to the low
level if the AT command is not
connected?
Answer: No, the module is AT mode in
an unconnected state. The user
does not need to send the AT
command in the case of
JDY-08
connection, and the P01 pin is
left unconnected
22 P00 PWRC Not connected, sleep, press, wake up,
After connection, wake up and press
disconnect
After connection, press awake when
asleep
23 RST reset Hardware reset pin
24 GND Power ground

AT Instruction
sequ instructions Effect Mast Working default
ence er / model
slav
e
1 AT+RST reset M/S －
2 AT+BOUD Serial baud setting M/S － 115200
3 AT+HOSTEN Master-slave setting M/S － From the
machine
4 AT+HOST Read host status M －
5 AT+DISC Disconnect M/S －
6 AT+ADVEN Turn on the radio S － open
7 AT+ADVIN Broadcast interval S － 100ms
8 AT+NEIN Connection interval S － 10ms
9 AT+POWR Transmitted power S － 0db
10 AT+NAME Broadcast name S － JDY-08
11 AT+MAC Read the MAC address M/S －
12 AT+STRUUID Set iBeacon UUID (string S iBeacon WeChat
type UUID) UUID
13 AT+HEXUUID Set iBeacon UUID (sixteen S iBeacon WeChat
hexadecimal type UUID) UUID
14 AT+MAJOR Set iBeacon Major (string S iBeacon 10
type Major)
15 AT+MINOR Set iBeacon Minor (string S iBeacon 7
type Minor)
16 AT+VER Read version number M/S － JDY-08-2.1
17 AT+VID Manufacturer identification S iBeacon 88
number sensor
18 AT+TEMP (used for factory S iBeacon 0
identification) sensor
JDY-08
19 AT+HUMID Temperature setting S iBeacon 0
sensor
20 AT+ISCEN Temperature setting S － Close
21 AT+PASS Sets whether to open a S － 123456
password connection
22 AT+SVRUUID Change service UUID M/S － FFE0
23 AT+CHRUUID Change features UUID M/S － FFE1
24 AT+SCAN Host scanner slave M Host
transmis
sion
25 AT+RSLV Read slave scan to slave M Host
MAC transmis
sion
26 AT+CONNET Connect scan to slave MAC M Host
transmis
sion
27 AT+BAND Bind slave MAC M －
28 AT+GETDCD The number of machines to M －
read from the host scan
29 AT+GETSTAT Find the working state of the M/S －
module
30 AT+PWMFRE Set PWM frequency M/S － 1000HZ
31 AT+PWMOPE Open PWM M/S － Close
N
32 AT+PWM1PU Set the pulse width of M/S － 50%
S PWM1
33 AT+PWM2PU Set the pulse width of M/S － 50%
S PWM2
34 AT+PWM3PU Set the pulse width of M/S － 50%
S PWM3
35 AT+PWM4PU Set the pulse width of M/S － 50%
S PWM4
36 AT+WXSVR WeChat H5 and server S WeChat H5
communication settings
37 AT+RTCFLSH RTC refresh time (seconds) M/S －
38 AT+RTCDAT RTC time reading and M/S －
E writing
39 AT+RTCOPE RTC switch M/S －
N
40 AT+RESTOR Restore factory M/S －
E configuration
41 AT+STARTEN Does the boot wake up? M/S Wake
mode
JDY-08
42 AT+SLEEP Sleep mode M/S
43 AT+KBYTE Transfer speed setting M/S 1K bytes/s
44 AT+REVERS P1_6 level and wake-up M/S 1
E MCU delay
45 AT+CLSS Set device type S passthro A0
ugh
46 AT+RTCALA RTC read and write timing M/S
M value
47 AT+ALAMEN RTC timing switch M/S close
48 AT+RSSI RSSI value S
49 AT+PIO AT command control IO M/S
50 AT+PARITY Serial parity bit setting Parity bit
51 AT+WXINEN WeChat automatic and S Manual
manual test mode selection mode

AT instruction specification
Special instructions: JDY-08 module, serial AT command does not need to add
terminator \r\n
Soft reset
Instruction response parameter
AT+RST, +OK, none AT+RST, +OK, none AT+RST, +OK, none

Settings / queries - P1_6 level mode (0-1 is only pin level change, and 2-6 is delayed
transmission)
Instruction response parameter
AT+REVERSE<Param> +OK Param: (0-6)
AT+REVERSE +REVERSE:<Para 0: connect low, not connected high
m> level
1: connect high level, not connected
low level
(0-1) principal and subordinate are
effective
When the parameter is set from 2 to
6, the P16 pin is usually
High level, delay XXms, recovery of
high level and the output data from
the APP, this method is not suitable
for large data transmission, only
suitable for small data transmission,
JDY-08
mainly for Bluetooth MCU MCU wake
up, usually in sleep, data APP,
Bluetooth wakes up the user MCU,
then output XXms delay data to the
MCU, this will ensure that the APP
sends data and can wake up the
MCU, MCU and APP (2-6 can
receive data from the machine)

2: delayed 50ms output data

3: delayed 100ms output data
4: delayed 200ms output data
5: delayed 400ms output data
6: delayed 1000ms output data
Default: 1
Special instructions: when set to 0-1, the connection pin P16 will have a change in the
connection state
Set 2-6, P16 is usually high, there is connection or APP data down, the module generates
a drop edge delay pulse, low level delay time, please according to the above delay
parameters through the AT instruction adjustment
This instruction is very useful for low power consumption products require a higher, and
this ensures that users of MCU can be normal in a sleep state, when the data is coming to
wake the user's MCU, and then the output data to the user MCU

Settings / queries - device type

Instruction response parameter
AT+CLSS<Param> +OK Param (00-FF)
AT+ CLSS + CLSS：<Param> IBeacon mode type
0XE0:iBeacon type
0XE1: temperature sensor
0XE2: humidity sensor
0XE3: temperature and
humidity sensor
0XE4: fragrant machine
0XE5: intelligent water meter
and meter reading
0XE6: voltage sensor
0XE0: current sensor
0XE0: weight scale
0XE0:PM2.5 sensor
Transparent mode type
0XA0: transmission 0
(Universal)
JDY-08
0XA1: transmission 1 (serial
output status)
0XA2: pass through 2
(Security)
0XA5: massage stick (AV
stick)
0XA6: massage bra
0XA7: massage chair
0XA8: tattoo machine
0XB1:LED light band
0XB2:LED bulb bulb
0XB3:LED candle light
0XC1: one way switch
controller
0XC2: dual switch controller
0XC3: three way switch
controller
0XC4: four way switch
controller
0XD1: air purifier
0XD5: water dispenser
0XD6: Ordinary electronic
locks
0XD7: fingerprint electronic
lock
Default: pass through 0
AT+ CLSS description:
Where is the difference between AT+ CLSS and AT+HOSTEN (module work mode
instructions)?
Answer: the AT+ CLSS device type is the device type of the AT+HOSTEN
Example 1: the user wants to configure the LED ribbon type to send AT instructions as
follows
1:AT+HOSTEN0 / / configured transparent transmission mode
2: AT+ CLSSB1 / / LED configuration into the lamp type
3: send AT+RST / reset
You configure the LED device type through the 3 steps above
Example 2: the user wants to configure the iBeacon type to send the AT instruction as
follows
1:AT+HOSTEN3 / / configured transparent transmission mode
2: AT+ CLSSE0 / / iBeacon type configuration
3: send AT+RST / reset
You configure the iBeacon device type through the 3 steps above
JDY-08
transparent Serial output status APP features PWRCPress
transmissi FFE2 function
on Con To Boot function awaken sleep
type nect brea print
k off
AT+CLSSA NO NO NO response Disconne awaken
0 ct
AT+CLSSA YES YES YES response Nonfuncti awaken
1 onal
AT+CLSSA NO NO NO No response Nonfuncti awaken
2 onal
Description: the factory default for AT+CLSSA0 type, this function is to pass through
common functions, such as the user of the product safety requirements are very
high, beware of other people use APP to modify the parameters can modify the
module (broadcast, broadcast interval, interval connection etc.), users can consider
using the AT+CLSSA2 model, some model of APP configuration parameters (no
response radio, radio, etc.), the connection interval interval of these parameters
can only be modified by AT instruction.
If the user MCU pins not much data, do not want to use MCU to determine the Bluetooth
connection status, you can consider using the AT+CLSSA1 mode, in this mode,
when a Bluetooth connected or disconnected from the serial output module, status
information to the user MCU
JDY-08
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
The modular can be installed or integrated in mobile or fix devices only. This
modular cannot be installed in any portable device.
FCC Radiation Exposure Statement
This modular complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter. This modular must be
installed and operated with a minimum distance of 20 cm between the radiator
and user body.
If the FCC identification number is not visible when the module is installed
inside another device, then the outside of the device into which the module is
installed must also display a label referring to the enclosed module. This
exterior label can use wording such as the following: “Contains Transmitter
Module FCC ID: 2AM2YJDY-08 Or ContainsFCC ID: 2AM2YJDY-08”
When the module is installed inside another device, the user manual of the
host must contain below warning statements;
1. This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference
that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
The devices must be installed and used in strict accordance with the
manufacturer's instructions as described in the user documentation that comes
with the product.
Any company of the host device which install this modular with limit modular
approval should perform the test of radiated emissionand spurious emission
according to FCC part 15C : 15.247 and 15.209 requirement,Only if the test
result comply with FCC part 15C : 15.247 and 15.209 requirement，then the
host can be sold legally.