Quality Solutions Product Data Sheet
RECECoat BASE
Basecoat Plastering Mortar
PRODUCT DESCRIPTION ADVANTAGES / CHARACTERISTICS
RECECOAT BASE is an innovative base plastering mortar • Easy to apply - Just add water
formulated to bind finishing plaster to level of surfaces • Sag Resistant
of beams and horizontal under slabs, and rectify verticality • Excellent adhesion. Less wastage
alignment of columns and walls where corrective thicker • High bonding strength. No need chipping of surfaces.
applications are required. • Long pot life & Open time. Increase productivity
• Non - Toxic and non - hazardous.
USAGES
•
• Applied for already smooth concrete surfaces APPLICATION
• Serve as base where conventional plastering is required. Preparation of substrate
The substrate must be clean and free from dust oil, paint or
Where non-valuable operation like “chipping” on concrete
surfaces, this product is the best substitute to avoid grease. The substrate has to be pre-wetted. Water accumulation
damaging the part of the structural element. on the surface must be avoided.
Mixing
RECECOAT BASE must be mixed with clean water at the site by
means of a powder drill whisk. Prepare the required water in a
suitable container, and then add RECECOAT BASE into the
container while stirring continuously until smooth, creamy
consistency is obtained. The mixture can be applied
immediately after mixing. No stand-off time is required
(For water consumption please refer to the technical data).
TECHNICAL DATA
Type Plastering mortar Coating
Form / Color Powder / Cement Grey
Material Coverage 5.0 - 6.0 m2 at 5 mm thick (with square notched trowel)
Wet Density (Freshly Mixed) 1.205 kg / litre (ASTM C172M)
Adhesion Strength @ 28 days approx. 1.0 - 1.5 MPa (ASTM D7234)
Compressive Strength @ 28 days approx. 11.5 - 12.5 MPa (ASTM C109)
Water Consumption 5.25 - 6.25 Litres / 25 kg-bag
Storage Store in a cool dry place
Shelf Life 12 months (in unopened original bag)
Packaging 25 kg / bag
P 1/2 Product Data Sheet www.rece.com.ph
Product Name: RECECOAT BASE
Rev. No: 004
Date Issued: 01 JANUARY 2019
Quality Solutions Product Data Sheet
RECECoat BASE LEGAL NOTICE
Basecoat Plastering Mortar
KEEP CONTAINER ALWAYS TIGHTLY CLOSED,
Application Proper
THIS PRODUCT IS FOR CONSTRUCTION AND INDUSTRIAL USE
RECECOAT BASE is applied by hand with a wooden
trowel, and is leveled of to a grooved surface with ONLY. THIS PRODUCT SHOULD BE USED ONLY BY
a square notched-trowel. (Such trowel can PROFESSIONALS.
be requested from RECE Manufacturing Corporation).
The information, and, in particular the recommendations
SAFETY PRECAUTIONS relating to the application and end- use of RECE MANUFACTURING
• Avoid contact with foodstuffs or food utensils. CORPORATION (RECE) products, are given in good faith based on
• Avoid prolonged skin contact. RECE current knowledge and experience of the products when
• Wear protective clothing. properly stored, handled and applied under normal conditions
• In the event of contamination, wash thoroughly with in accordance with RECE. In practice, the differences in materials,
water. substrates and actual site conditions are such that no warranty
• If the eyes or mouth are affected, wash with water and in respect of merchantability or of fitness for a particular
immediately and obtain medical attention. purpose, nor any liability arising out of any legal relationship
whatsoever, can be inferred either from this information, or
HEALTH AND SAFETY from any written recommendations, or from any other advice
For information and advice on the safe handling, offered. The user of the product must test the product’s
storage and disposal of chemical products, user shall suitability for the intended application and purpose. RECE
refer to the most recent MSDS containing physical, reserves the right to change the properties of its products. The
ecological, toxicological and other safety-related data. proprietary rights of third parties must be observed. All orders
are accepted subject to our current terms of sale and delivery.
Users must always refer to the most recent issue of the local
Product Data Sheet for the product concerned, copies of which
will be supplied on request.
The “RECE” brand is exclusively distributed by:
RECE MANUFACTURING CORPORATION
Km. 16, Aguinaldo Highway, CMC Building 2,
Panapaan II, Bacoor City, Cavite 4102, Philippines
For technical support please call us at: (02) 984 1622
P 2/2 Product Data Sheet www.rece.com.ph
Product Name: RECECOAT BASE
Rev. No: 003
Date Issued: 01 JANUARY 2019
