Scribd
Upload
59 views3 pages

Engineers' Educare Coaching Centre (Eecc) : Junior Engineer (Civil Engineering) - Demo Mock Test

This document contains a 12 question mock test for the position of Junior Engineer (Civil Engineering). The questions cover topics in soil mechanics, structural analysis, transportation engineering, and construction materials. The full mock test, along with solutions and analysis, can be viewed at the provided YouTube link. Contact information is also provided for Engineers' Education Coaching Centre.

Uploaded by

Majik Taye
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
59 views3 pages

Engineers' Educare Coaching Centre (Eecc) : Junior Engineer (Civil Engineering) - Demo Mock Test

This document contains a 12 question mock test for the position of Junior Engineer (Civil Engineering). The questions cover topics in soil mechanics, structural analysis, transportation engineering, and construction materials. The full mock test, along with solutions and analysis, can be viewed at the provided YouTube link. Contact information is also provided for Engineers' Education Coaching Centre.

Uploaded by

Majik Taye
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

enginEErs’ EDUCARE COACHING CENTRE (EECC)

TARA COMPLEX, NERIST GATE


NIRJULI, PAPUMPARE, ARUNACHAL PRADESH - 791109
Mobile: +91 84030 81436 Phone:0360 2257190
Email: [email protected] Website: eecconline.com

JUNIOR ENGINEER (CIVIL ENGINEERING) – DEMO MOCK TEST


Check Solution and Analysis at: https://youtu.be/EayeXj9vQws
1. When the plastic limit of the soil is greater then the liquid limit, then the plasticity
index is reported as
a) negative
b) zero
c) non-plastic (NP)
d) 1
2. A combined footing is generally used when
a) number of column is more than two and they are spaced far apart
b) Number of column is two and they are spaced close to each other.
c) Number of column is two and they are spaced far apart.
d) there is only one column
3. The relationship between water content (w%) and number of blows (N) in soils, as
obtained from Casagrande's liquid limit device, is given by
w = 20 -log10 N
The liquid limit of the soil is
a) 15.6%
b) 16.6%
c) 17.6%
d) 18.6%
4. In the most general form of Bernoulli's equation
𝑃𝑃 𝑣𝑣 2
𝑤𝑤
+ + 𝑧𝑧 = 𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐
2𝑔𝑔

each term represents


a) energy per unit mass
b) energy per unit weight
c) energy per unit volume
d) none of the above
5. For laminar flow in circular pipes the Darcy's friction factor f is equal to
a) 16/Re
b) 32/ Re
c) 64/ Re
d) none of the above
6. Calculate the limiting length (m) of offset, if the maximum allowable error in laying
offset is 2 degree. The scale of the map is 1 cm = 100m.
a) 2.5 b) 71.63 c) 250 d) 230
7. The radius of the horizontal curve is 100 m. The design speed is 50 km/hr and the
design coefficient of lateral friction is 0.15. Determine the rate of super elevation to
be provided, if full lateral friction is assumed to develop
a) 1 in 26.4 b) 1 in 10.5 c) 1 in 17 d) 1 in 21.2
8. The point on the beam where bending moment becomes zero or changes its curvature
is called
a) point of zero shear
b) point of maximum shear
c) point of contraflacture
d) none of these
9. The point on beam where bending moment is maximum, the shear force at that point
must be ................
10. Angle of repose is a ………. angle
a) Right angle
b) Equal angle
c) Minimum angle
d) Maximum angle
11. Which of the following is a proper sequence?
a) Proportional limit, elastic limit, yielding failure
b) Elastic limit, proportional limit, yielding, failure
c) Yielding, proportional limit, elastic limit, failure
d) None of the above
12. The section in which concrete is not fully stressed to its permissible value when stress
in steel reaches its maximum value, is called
a) Under reinforced section
b) Over-reinforced section
c) Critical section
d) Balanced section

You might also like