Internal Use Only

North/Latin America http://aic.lgservice.com

Europe/Africa http://eic.lgservice.com
Asia/Oceania http://biz.lgservice.com

LED TV
SERVICE MANUAL
CHASSIS : LW50A

MODEL : 23MT77V 23MT77V-PZS

CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

P/NO : MFL68127287 (1501-REV00) Printed in Korea

 CONTENTS

CONTENTS ............................................................................................... 2

SAFETY PRECAUTIONS.......................................................................... 3

SERVICING PRECAUTIONS..................................................................... 4

SPECIFICATION........................................................................................ 6

ADJUSTMENT INSTRUCTION............................................................... 10

TROUBLE SHOOTING............................................................................ 15

BLOCK DIAGRAM................................................................................... 19

EXPLODED VIEW ................................................................................... 20

SCHEMATIC CIRCUIT DIAGRAM ............................................ APPENDIX

Copyright © LG Electronics. Inc. All right reserved. -2- LGE Internal Use Only
Only for training and service purposes
 SAFETY PRECAUTIONS
IMPORTANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the
Schematic Diagram and Exploded View.
It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent
Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.

General Guidance Leakage Current Hot Check (See below Figure)

Plug the AC cord directly into the AC outlet.
An isolation Transformer should always be used during the
servicing of a receiver whose chassis is not isolated from the AC Do not use a line Isolation Transformer during this check.
power line. Use a transformer of adequate power rating as this Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor
protects the technician from accidents resulting in personal injury between a known good earth ground (Water Pipe, Conduit, etc.)
from electrical shocks. and the exposed metallic parts.
Measure the AC voltage across the resistor using AC voltmeter
It will also protect the receiver and it's components from being with 1000 ohms/volt or more sensitivity.
damaged by accidental shorts of the circuitry that may be Reverse plug the AC cord into the AC outlet and repeat AC voltage
inadvertently introduced during the service operation. measurements for each exposed metallic part. Any voltage
measured must not exceed 0.75 volt RMS which is corresponds to
If any fuse (or Fusible Resistor) in this TV receiver is blown, 0.5mA.
replace it with the specified. In case any measurement is out of the limits specified, there is
possibility of shock hazard and the set must be checked and
When replacing a high wattage resistor (Oxide Metal Film Resistor, repaired before it is returned to the customer.
over 1W), keep the resistor 10mm away from PCB.
Leakage Current Hot Check circuit
Keep wires away from high voltage or high temperature parts.
AC Volt-meter

Before returning the receiver to the customer,

always perform an AC leakage current check on the exposed Good Earth Ground
such as WATER PIPE,
metallic parts of the cabinet, such as antennas, terminals, etc., to CONDUIT etc.
To Instrument's
be sure the set is safe to operate without damage of electrical exposed
0.15µF
shock. METALLIC PARTS

Leakage Current Cold Check(Antenna Cold Check) 1.5 Kohm/10W

With the instrument AC plug removed from AC source, connect an
electrical jumper across the two AC plug prongs. Place the AC
When 25A is impressed between Earth and 2nd Ground
switch in the on position, connect one lead of ohm-meter to the AC for 1 second, Resistance must be less than 0.1
plug prongs tied together and touch other ohm-meter lead in turn to *Base on Adjustment standard
each exposed metallic parts such as antenna terminals, phone
jacks, etc.
If the exposed metallic part has a return path to the chassis, the
measured resistance should be between 1MΩ and 5.2MΩ.
When the exposed metal has no return path to the chassis the
reading must be infinite.
An other abnormality exists that must be corrected before the
receiver is returned to the customer.

Copyright © LG Electronics. Inc. All right reserved. -3- LGE Internal Use Only
Only for training and service purposes
 SERVICING PRECAUTIONS
CAUTION: Before servicing receivers covered by this service unit under test.
manual and its supplements and addenda, read and follow the 2. After removing an electrical assembly equipped with ES
SAFETY PRECAUTIONS on page 3 of this publication. devices, place the assembly on a conductive surface such as
NOTE: If unforeseen circumstances create conflict between the aluminum foil, to prevent electrostatic charge buildup or
following servicing precautions and any of the safety precautions on exposure of the assembly.
page 3 of this publication, always follow the safety precautions. 3. Use only a grounded-tip soldering iron to solder or unsolder ES
Remember: Safety First. devices.
4. Use only an anti-static type solder removal device. Some solder
General Servicing Precautions removal devices not classified as "anti-static" can generate
1. Always unplug the receiver AC power cord from the AC power electrical charges sufficient to damage ES devices.
source before; 5. Do not use freon-propelled chemicals. These can generate
a. Removing or reinstalling any component, circuit board electrical charges sufficient to damage ES devices.
module or any other receiver assembly. 6. Do not remove a replacement ES device from its protective
b. Disconnecting or reconnecting any receiver electrical plug or package until immediately before you are ready to install it.
other electrical connection. (Most replacement ES devices are packaged with leads
c. Connecting a test substitute in parallel with an electrolytic electrically shorted together by conductive foam, aluminum foil
capacitor in the receiver. or comparable conductive material).
CAUTION: A wrong part substitution or incorrect polarity 7. Immediately before removing the protective material from the
installation of electrolytic capacitors may result in an leads of a replacement ES device, touch the protective material
explosion hazard. to the chassis or circuit assembly into which the device will be
installed.
2. Test high voltage only by measuring it with an appropriate high CAUTION: Be sure no power is applied to the chassis or circuit,
voltage meter or other voltage measuring device (DVM, and observe all other safety precautions.
FETVOM, etc) equipped with a suitable high voltage probe. 8. Minimize bodily motions when handling unpackaged
Do not test high voltage by "drawing an arc". replacement ES devices. (Otherwise harmless motion such as
3. Do not spray chemicals on or near this receiver or any of its the brushing together of your clothes fabric or the lifting of your
assemblies. foot from a carpeted floor can generate static electricity
4. Unless specified otherwise in this service manual, clean sufficient to damage an ES device.)
electrical contacts only by applying the following mixture to the
contacts with a pipe cleaner, cotton-tipped stick or comparable General Soldering Guidelines
non-abrasive applicator; 10% (by volume) Acetone and 90% (by 1. Use a grounded-tip, low-wattage soldering iron and appropriate
volume) isopropyl alcohol (90%-99% strength) tip size and shape that will maintain tip temperature within the
CAUTION: This is a flammable mixture. range or 500 ˚F to 600 ˚F.
Unless specified otherwise in this service manual, lubrication of 2. Use an appropriate gauge of RMA resin-core solder composed
contacts in not required. of 60 parts tin/40 parts lead.
5. Do not defeat any plug/socket B+ voltage interlocks with which 3. Keep the soldering iron tip clean and well tinned.
receivers covered by this service manual might be equipped. 4. Thoroughly clean the surfaces to be soldered. Use a mall wire-
6. Do not apply AC power to this instrument and/or any of its bristle (0.5 inch, or 1.25cm) brush with a metal handle.
electrical assemblies unless all solid-state device heat sinks are Do not use freon-propelled spray-on cleaners.
correctly installed. 5. Use the following unsoldering technique
7. Always connect the test receiver ground lead to the receiver a. Allow the soldering iron tip to reach normal temperature.
chassis ground before connecting the test receiver positive (500 ˚F to 600 ˚F)
lead. b. Heat the component lead until the solder melts.
Always remove the test receiver ground lead last. c. Quickly draw the melted solder with an anti-static, suction-
8. Use with this receiver only the test fixtures specified in this type solder removal device or with solder braid.
service manual. CAUTION: Work quickly to avoid overheating the circuit
CAUTION: Do not connect the test fixture ground strap to any board printed foil.
heat sink in this receiver. 6. Use the following soldering technique.
a. Allow the soldering iron tip to reach a normal temperature
Electrostatically Sensitive (ES) Devices (500 ˚F to 600 ˚F)
Some semiconductor (solid-state) devices can be damaged easily b. First, hold the soldering iron tip and solder the strand against
by static electricity. Such components commonly are called the component lead until the solder melts.
Electrostatically Sensitive (ES) Devices. Examples of typical ES c. Quickly move the soldering iron tip to the junction of the
devices are integrated circuits and some field-effect transistors and component lead and the printed circuit foil, and hold it there
semiconductor "chip" components. The following techniques only until the solder flows onto and around both the
should be used to help reduce the incidence of component component lead and the foil.
damage caused by static by static electricity. CAUTION: Work quickly to avoid overheating the circuit
1. Immediately before handling any semiconductor component or board printed foil.
semiconductor-equipped assembly, drain off any electrostatic d. Closely inspect the solder area and remove any excess or
charge on your body by touching a known earth ground. splashed solder with a small wire-bristle brush.
Alternatively, obtain and wear a commercially available
discharging wrist strap device, which should be removed to
prevent potential shock reasons prior to applying power to the

Copyright © LG Electronics. Inc. All right reserved. -4- LGE Internal Use Only
Only for training and service purposes
IC Remove/Replacement CAUTION: Maintain original spacing between the replaced
Some chassis circuit boards have slotted holes (oblong) through component and adjacent components and the circuit board to
which the IC leads are inserted and then bent flat against the prevent excessive component temperatures.
circuit foil. When holes are the slotted type, the following technique
should be used to remove and replace the IC. When working with Circuit Board Foil Repair
boards using the familiar round hole, use the standard technique Excessive heat applied to the copper foil of any printed circuit
as outlined in paragraphs 5 and 6 above. board will weaken the adhesive that bonds the foil to the circuit
board causing the foil to separate from or "lift-off" the board. The
Removal following guidelines and procedures should be followed whenever
1. Desolder and straighten each IC lead in one operation by gently this condition is encountered.
prying up on the lead with the soldering iron tip as the solder
melts. At IC Connections
2. Draw away the melted solder with an anti-static suction-type To repair a defective copper pattern at IC connections use the
solder removal device (or with solder braid) before removing the following procedure to install a jumper wire on the copper pattern
IC. side of the circuit board. (Use this technique only on IC
Replacement connections).
1. Carefully insert the replacement IC in the circuit board.
2. Carefully bend each IC lead against the circuit foil pad and 1. Carefully remove the damaged copper pattern with a sharp
solder it. knife. (Remove only as much copper as absolutely necessary).
3. Clean the soldered areas with a small wire-bristle brush. 2. carefully scratch away the solder resist and acrylic coating (if
(It is not necessary to reapply acrylic coating to the areas). used) from the end of the remaining copper pattern.
3. Bend a small "U" in one end of a small gauge jumper wire and
"Small-Signal" Discrete Transistor carefully crimp it around the IC pin. Solder the IC connection.
Removal/Replacement 4. Route the jumper wire along the path of the out-away copper
1. Remove the defective transistor by clipping its leads as close as pattern and let it overlap the previously scraped end of the good
possible to the component body. copper pattern. Solder the overlapped area and clip off any
2. Bend into a "U" shape the end of each of three leads remaining excess jumper wire.
on the circuit board.
3. Bend into a "U" shape the replacement transistor leads. At Other Connections
4. Connect the replacement transistor leads to the corresponding Use the following technique to repair the defective copper pattern
leads extending from the circuit board and crimp the "U" with at connections other than IC Pins. This technique involves the
long nose pliers to insure metal to metal contact then solder installation of a jumper wire on the component side of the circuit
each connection. board.

Power Output, Transistor Device 1. Remove the defective copper pattern with a sharp knife.
Removal/Replacement Remove at least 1/4 inch of copper, to ensure that a hazardous
1. Heat and remove all solder from around the transistor leads. condition will not exist if the jumper wire opens.
2. Remove the heat sink mounting screw (if so equipped). 2. Trace along the copper pattern from both sides of the pattern
3. Carefully remove the transistor from the heat sink of the circuit break and locate the nearest component that is directly
board. connected to the affected copper pattern.
4. Insert new transistor in the circuit board. 3. Connect insulated 20-gauge jumper wire from the lead of the
5. Solder each transistor lead, and clip off excess lead. nearest component on one side of the pattern break to the lead
6. Replace heat sink. of the nearest component on the other side.
Carefully crimp and solder the connections.
Diode Removal/Replacement CAUTION: Be sure the insulated jumper wire is dressed so the
1. Remove defective diode by clipping its leads as close as it does not touch components or sharp edges.
possible to diode body.
2. Bend the two remaining leads perpendicular y to the circuit
board.
3. Observing diode polarity, wrap each lead of the new diode
around the corresponding lead on the circuit board.
4. Securely crimp each connection and solder it.
5. Inspect (on the circuit board copper side) the solder joints of
the two "original" leads. If they are not shiny, reheat them and if
necessary, apply additional solder.

Fuse and Conventional Resistor

Removal/Replacement
1. Clip each fuse or resistor lead at top of the circuit board hollow
stake.
2. Securely crimp the leads of replacement component around
notch at stake top.
3. Solder the connections.

Copyright © LG Electronics. Inc. All right reserved. -5- LGE Internal Use Only
Only for training and service purposes
 SPECIFICATION
NOTE : Specifications and others are subject to change without notice for improvement.

1. Application Range 3.Test method

This spec sheet is applied all of the TV used LW50A chassis. 1) Performance : LGE TV test method followed
2) Demanded other specification
- Safety : CE,IEC specification
- EMC : CE,IEC specification
2. Specification
Each part is tested as below without special appointment

1) Temperature : 25 ˚C ± 5 ˚C (77 ˚F ± 9 ˚F),

CST : 40 ˚C ± 5 ˚C
2) Relative Humidity : 65 % ± 10 %
3) Power Voltage : Standard input voltage
(100 V - 240 ­V ~, 50 / 60 Hz)
·S  tandard Voltage of each products is marked by models
4) Specification and performance of each parts are followed
each drawing and specification by part number in accord-
ance with BOM.
5) The receiver must be operated for about 5 minutes prior to
the adjustment.

4. General specification
4.1. TV
No Item Specification Remarks

1 Market EU(PAL/DVB Market) DTV & Analog (Total 37 countries)

DTV (MPEG2/4, DVB-T) :37 countries
UK/Italy/Germany/France/Spain/Sweden/Finland/Nether-
lands/ Belgium/Luxemburg/ Greece/Denmark/Czech/
Austria /Hungary/Swiss/Croatia/Turkey
Norway/Slovenia/Poland/Ukraine/Portugal/Ireland/Morocco/
Latvia/Estonia/Lithania/Rumania/Bulgaria/Russia/Slovakia
Bosnia/Serbia/Albania/Kazakhstan/Belarus
*4 Country, Nordic option(EU model only)
- Denmark , Finland, Norway, Sweden
DTV (MPEG2/4, DVB-T2): 8 countries
UK/Denmark/Sweden/Finland/Norway/Ireland/Ukraine/
Kazakhstan
DTV (MPEG2/4, DVB-C): 37 countries
UK/Italy/Germany/France/Spain/Sweden/Finland/Nether-
lands/ Belgium/Luxemburg/ Greece/Denmark/Czech/
Austria /Hungary/Swiss/Croatia/Turkey
Norway/Slovenia/Poland/Ukraine/Portugal/Ireland/Morocco/
Latvia/Estonia/Lithania/Rumania/Bulgaria/Russia/Slovakia
Bosnia/Serbia/Albania/Kazakhstan/Belarus
DTV (MPEG2/4,DVB-S): 29 countries
Italy/Germany/France/Spain/Netherlands/ Belgium/
Luxemburg/ Greece/ Czech/Austria /Hungary/Swiss/Croatia/
Turkey/Slovenia/Poland/Portugal/ Morocco/Latvia/
Estonia/Lithuania/Rumania/Bulgaria/Russia/Slovakia
Bosnia/Serbia/Albania/ Belarus
Supported satellite : 22 satellites
HISPASAT 1C/1D, ATLANTIC BIRD 2, NILESAT 101/102,
ATLANTIC BIRD 3, AMOS 2/3, THOR 5/6, IRIUS 4,
EUTELSAT-W3A, EUROBIRD 9A, EUTELSAT-W2A, HOT-
BIRD 6/8/9, EUTELSAT-SESAT, ASTRA 1L/H/M/KR, ASTRA
3A/3B, BADR 4/6, ASTRA 2D, EUROBIRD 3, EUTELSAT-
W7, HELLASSAT 2, EXPRESS AM1, TURKSAT 2A/3A,
INTERSAT10

Copyright © LG Electronics. Inc. All right reserved. -6- LGE Internal Use Only
Only for training and service purposes
 No Item Specification Remarks

2 Broadcasting system - Analogue TV Analogue TV :

1) PAL-BG (RF) VHF: E2 to E12, UHF : E21 to E69
2) PAL-DK (CATV) S1 to S20, HYPER: S21 to S47
3) PAL-I/I’ Digital TV : VHF, UHF
4) SECAM-BG Satellite TV : VHF, UHF,
5) SECAM-DK C-Band, Ku-Band
6) SECAM L/L’ * DVB-T2 ( T2 model only support )
*DVB-S/S2(Satellite model only support )
- Digital TV
1) DVB-T/C/T2

- Satellite Digital TV
1) DVB-S/S2
3 Channel Storage ATV – 135EA, DTV – 1000EA

4 Receiving system Analog : Upper Heterodyne ► DVB-T

Digital : COFDM, QAM - Guard Interval(Bitrate_Mbit/s)
1/4, 1/8, 1/16, 1/32
- Modulation : Code Rate
QPSK : 1/2, 2/3, 3/4, 5/6, 7/8
16-QAM : 1/2, 2/3, 3/4, 5/6, 7/8
64-QAM : 1/2, 2/3, 3/4, 5/6, 7/8
► DVB-T2
- Guard Interval(Bitrate_Mbit/s)
1/4, 1/8, 1/16, 1/32, 1/128, 19/128, 19/256,
- Modulation : Code Rate
QPSK : 1/2, 2/5, 2/3, 3/4, 5/6
16-QAM : 1/2, 2/5, 2/3, 3/4, 5/6
64-QAM : 1/2, 2/5, 2/3, 3/4, 5/6
256-QAM : 1/2, 2/5, 2/3, 3/4, 5/6
► DVB-C
- Symbolrate :
4.0Msymbols/s to 7.2Msymbols/s
- Modulation :
16QAM, 64-QAM, 128-QAM and 256-QAM
► DVB-S/S2
- symbolrate
DVB-S2 (8PSK / QPSK) : 2 ~ 45Msymbol/s
DVB-S (QPSK) : 2 ~ 45Msymbol/s
- viterbi
DVB-S mode : 1/2, 2/3, 3/4, 5/6, 7/8
DVB-S2 mode : 1/2, 2/3, 3/4, 3/5, 4/5, 5/6, 8/9, 9/10
5 Interface RF / Composite (CVBS) / Com- Scart Jack is Full scart and support RF-OUT(analog)
ponent / HDMI / D-Sub / Scart /
USB / Audio In / Headphone Out /
LAN(option)
6 DVB DVB-T CI : U
 K, Finland, Denmark, Norway, Sweden, Russia, Spain,
Ireland, Luxemburg, Belgium, Netherland
CI+ : France(Canal+), Italy(DGTVi)
DVB-C CI : Switzerland, Austria, Slovenia, Hungary, Bulgaria
CI+ : S
 witzerland(UPC,Cablecom), Netherland(Ziggo),
Germany(KDG,CWB), Finland(labwise)
DVB-S CI + : Germany (Astra HD+)

Copyright © LG Electronics. Inc. All right reserved. -7- LGE Internal Use Only
Only for training and service purposes
5. External Input Support Format
5.1. RGB/ HDMI (PC)
No. Resolution H-freq(kHz) V-freq(Hz) Pixel clock(MHz) Remark
1 720*400 31.468 70.080 28.321
2 640*480 31.469 59.940 25.175
3 640*480 37.500 75.000 31.500
4 800*600 37.879 60.317 40.000
5 800*600 46.875 75.000 49.500
6 1024*768 48.363 60.004 65.000
7 1024*768 56.476 70.069 75.000 HDMI(PC) only
8 1024*768 60.023 75.029 78.750
9 1152*864 67.500 75.000 108.000
10 1280*720 45.000 60.000 74.250
11 1280*800 49.702 59.810 83.500
12 1280*1024 63.981 60.020 108.000
13 1280*1024 79.976 75.025 135.000
14 1400*1050 65.317 59.978 121.750
15 1440*900 55.935 59.887 106.500
16 1600*900 60.000 60.000 108.000
17 1680*1050 64.674 59.883 119.000
18 1680*1050 65.290 59.954 146.250
19 1920*1080 67.500 60.000 148.500

5.2. HDMI (DTV)

No. Resolution H-freq(kHz) V-freq(Hz) Pixel Remark
clock(MHz)
1 720* 480 31.469 / 31.5 59.94 / 60 27.00/ 27.03 SDTV 480P
2. 720*576 31.25 50.00 27.864 SDTV 576P
3. 1280*720 37.50 50.00 74.250 HDTV 720P
4 1280* 720 44.96 / 45 59.94 / 60 74.17/ 74.25 HDTV 720P
5 1920* 1080 33.72 / 33.75 59.94 / 60 74.17/ 74.25 HDTV 1080I
6 1920* 1080 28.125 50.00 74.25 HDTV 1080I
7 1920* 1080 27.00 24 74.25 HDTV 1080P
8 1920* 1080 33.75 30.00 74.25 HDTV 1080P
9 1920* 1080 56.250 50 148.5 HDTV 1080P
10 1920* 1080 67.43 / 67.5 59.94 / 60 148.35/ 148.50 HDTV 1080P

Copyright © LG Electronics. Inc. All right reserved. -8- LGE Internal Use Only
Only for training and service purposes
5.3. AV (Component supported mode)
Specification
No Remark
Resolution H-freq(kHz) V-freq(Hz) Pixel clock( MHz)
1 720* 480 15.73 59.94 13.500 SDTV, DVD 480I( 525I)
2 720* 480 15.75 60.00 13.514 SDTV, DVD 480I( 525I)
3 720* 576 15.625 50.00 13.500 SDTV, DVD 576I( 625I) 50Hz
4 720* 480 31.47 59.94 27.000 SDTV 480P
5 720* 480 31.50 60.00 27.027 SDTV 480P
6 720* 576 31.25 50.00 27.000 SDTV 576P 50Hz
7 1280* 720 44.96 59.94 74.176 HDTV 720P
8 1280* 720 45.00 60.00 74.250 HDTV 720P
9 1280* 720 37.50 50.00 74.25 HDTV 720P 50Hz
10 1920* 1080 33.72 59.94 74.176 HDTV 1080I
11 1920* 1080 33.75 60.00 74.250 HDTV 1080I
12 1920* 1080 28.125 50.00 74.250 HDTV 1080I 50Hz
13 1920* 1080 56.25 50 148.5 HDTV 1080P
14 1920* 1080 67.432 59.94 148.350 HDTV 1080P
15 1920* 1080 67.5 60.00 148.5 HDTV 1080P

Copyright © LG Electronics. Inc. All right reserved. -9- LGE Internal Use Only
Only for training and service purposes
 ADJUSTMENT INSTRUCTION
1. Application Range 4) Click "Read" tab, and then load download file(XXXX.bin) by
clicking "Read"
This document is applied to LW50A chassis TV which is
manufactured in TV (or Monitor) Factory or is produced on the (4)
basis of this data.
filexxx.bin

2. Designation
1) The adjustment is according to the order which is designat-
ed and which must be followed, according to the plan which
can be changed only on agreeing.
2) Power adjustment : Free Voltage.
3) Magnetic Field Condition: Nil. 5) Click "Auto" tab and set as below
4) Input signal Unit: Product Specification Standard. 6) Click "Run".
5) Reserve after operation: Above 5 Minutes (Heat Run) 7) After downloading, check "OK" message.
Temperature : at 25 °C ± 5 °C
Relative humidity : 65 % ± 10 % (5)
Input voltage : 220 V, 60 Hz
6) Adjustment equipments : Color Analyzer (CA-210 or CA- (5)
110), DDC Adjustment Jig equipment, SVC remote control-
ler. (7) ……….OK
7) Push The "IN STOP KEY" – For memory initialization
Case1 : Software version up (6)
1) After downloading S/W by USB , Multi-vision set will
reboot automatically
2) Push "In-stop" key
3) Push "Power on" key
4) Function inspection * USB DOWNLOAD(*.epk file download)
5) After function inspection, Push "In-stop" key. 1) Make New folder named "LG_DTV" and put ISP file(*.epk)
in the folder.
Case2 : Function check at the assembly line 2) Put the USB Stick to the USB socket.
1) When TV set is entering on the assembly line, Push "In- 3) Automatically detecting update file in USB Stick
stop" key at first. - If your downloaded program version in USB Stick is
2) Push "Power on" key for turning it on. Low, it didn’t work. But your downloaded version is
→ If you push "Power on" key, TV set will recover channel High, USB data is automatically detecting.
information by itself. 4) Show the message "Copy the file from the Memory…"
3) After function inspection, Push "In-stop" key.

3. Main PCB check process

* APC - After Manual-Insult, executing APC
5) Updating is starting.

* Boot file Download

1) Execute ISP program "Mstar ISP Utility" and then click
"Config" tab.
2) Set as below, and then click "Auto Detect" and check "OK"
message. If display "Error", Check connect computer, jig,
and set.
3) Click "Connect" tab. If display "Can’t ", Check connect 6) Updating Completed, The TV will restart automatically.
computer, jig, and set. 7) If your TV is turned on, check your updated version and
(1) (3) Tool option. (explain the Tool option, next stage)
* If downloading version is more high than your TV
Please Check the Speed :
have, TV can lost all channel data. In this case, you
Use the speed under have to channel recover. if all channel data is cleared,
200KHz. you didn’t have a DTV/ATV test on production line.
(2) OK

Copyright © LG Electronics. Inc. All right reserved. - 10 - LGE Internal Use Only
Only for training and service purposes
3.1. ADC Process (Optional) : 3.2.1. EDID Data Check Sum
If ADC processes as OTP, There is Input Block(0) Block(1)

no need to proceed internal ADC. RGB BC -

1) Enter Service Mode by pushing "ADJ" key. HDMI1 13 7E
2) Enter Internal ADC mode by pushing "►" key at "ADC
HDMI2 13 6E
Calibration"
- RGB

- HDMI1

→ Caution: Using ‘P-ONLY’ button of the Adjustment R/C,

power on TV.

* ADC Calibration Protocol (RS232)

NO Item CMD CMD Data 0
1 2

Enter Download A A 0 0 When transfer the

download ‘Mode In’ ‘Mode In’,
MODE Carry the command.

EDID data and Download A E 00 10 Automatically download

Model option (The use of a internal
download Data)

▪ aa 00 00 [Enter Adjust Mode]

▪ xb 00 40 [Component Input ] - HDMI2
▪ ad 00 10 [Adjust 480i & 1080p Comp]
▪ aa 00 90 End Adjust mode
* Required equipment : Adjustment R/C.

3.2. EDID Download

1) After enter Service Mode by pushing "ADJ" key.
2) Enter EDID D/L mode.
3) Enter "START" by pushing "OK" key.

3.3. Function Check

3.3.1. Check display and sound
*Check Input and Signal items. (cf. work instructions)
1) TV(DTV, RF, Satellite(Satellite model))
2) AV (SCART/CVBS)
→ Caution : Never connect RGB/HDMI cable when EDID 3) COMPONENT (480i)
downloaded. 4) HDMI1/2(PC : 1920 x 1080 @ 60Hz)
5) RGB(PC : 1920 x 1080 @ 60Hz)
* Edid data and Model option download (RS232) 6) PC Audio In
NO Item CMD CMD Data 0 7) Headphone out
1 2 8) USB
* Display and Sound check is executed by Remote controller
Enter Download 'Mode In' A A 0 0
download MODE * Some models do not support RGB & PC audio in. It depends on
model spec.
EDID data and Download A E 00 10
→ Caution : Not to push the INSTOP KEY after completion if the func-
Model option
download tion inspection.

Copyright © LG Electronics. Inc. All right reserved. - 11 - LGE Internal Use Only
Only for training and service purposes
4. Total Assembly line process Auto-control interface and directions
1) |Adjust in the place where the influx of light like floodlight
4.1. White Balance adjustment around is blocked. (Illumination is less than 10ux).
1) Color Analyzer: CA-210 (LED Module : CH 14) 2) |Adhere closely the Color Analyzer ( CA210 ) to the mod-
2) Adj. Computer(During auto adj., RS-232C protocol is ule less than 10cm distance, keep it with the surface of the
needed) Module and Color Analyzer’s Prove vertically.(90° +/- 2.5°).
3) Service Remote Controller
*RGB Gains are fixed data for each model.
Insert RS-232C Jack which is connected with PC for White
Balance or equivalent device.
→ Total Assembly line should be check whether the color
coordinate(x,y) data refer to below table were meet or not.
Color coordinate is differ from panel’s characteristics of color
temperature. Please check panel characteristics about color
temperature.
-Warm Panel
Color Cool 9,300k °K X=0.291 (±0.04) <Test Signal>
Temperature Y=0.294 (±0.04) Inner pattern
(204gray,80IRE)
Medium 8,000k °K X=0.300 (±0.04) 3) Aging time
Y=0.310 (±0.04)
-. After aging start, keep the power on (no suspension of
Warm 6,500k °K X=0.318 (±0.04) power supply) and heat-run over 5 minutes.
Y=0.334 (±0.04)
-. Using ‘no signal’ or ‘POWER ONLY’ or the others, check the
Luminance Cool Min : 70 Typ : 110 <Test Signal> back light on.
(cd/m²) Inner pattern
Medium Min : 70 Typ : 110 (204gray,80IRE)
Warm Min : 70 Typ : 110
* Auto adjustment Map(using RS-232C to USB cable)
RS-232C COMMAND
[ CMD ID DATA ]
▪ White Balance Default value Wb 00 00 White Balance Start
Gain Cut Wb 00 ff White Balance End
R G B R G B RS-232C M CENTER M
MT57 22MT57 LGD Cool 125 130 192 64 64 64 COMMAND I (DEFAULT) A
(AH-IPS)
Medium 161 170 210 64 64 64 [CMD ID DATA] N X
Warm 185 185 192 64 64 64 Cool Mid Warm Cool Mid Warm
24MT57 LGD Cool 120 110 192 64 64 64 R Gain jg Ja jd 00 172 192 192 254
(AH-IPS)
Medium 170 172 220 64 64 64
G Gain jh Jb je 00 172 192 192 192
Warm 180 180 192 64 64 64
B Gain ji Jc jf 00 192 192 172 254
27MT57 LGD Cool 83 99 192 64 64 64
(AH-IPS) R Cut 64 64 64 128
Medium 161 171 244 64 64 64
G Cut 64 64 64 128
Warm 187 174 192 64 64 64

27MT57 HEESUNG Cool 110 119 192 64 64 64

B Cut 64 64 64 128
Medium 159 172 221 64 64 64
** Caution **
Warm 167 174 192 64 64 64 Color Temperature : Cool, Medium, Warm.
MT77 23MT77 LGD_B2D Cool 115 121 192 64 64 64 One of R Gain/G Gain/ B Gain should be kept on 0xC0, and
Medium 165 172 220 64 64 64
adjust other two lower than C0. (when R/G/B Gain are all C0,
it is the FULL Dynamic Range of Module)
Warm 183 180 192 64 64 64

24MT77 LGD_B2D Cool 114 124 192 64 64 64

Medium 159 172 218 64 64 64

Warm 184 184 192 64 64 64

27MT77 LGD_B2D Cool 116 129 192 64 64 64

Medium 156 172 215 64 64 64

183 186 192 64 64 64

* Connecting picture of the measuring instrument

(On Automatic control)
Inside PATTERN is used when W/B is controlled. Connect to
auto controller or push Adjustment R/C P-ONLY → Enter the
mode of White-Balance, the pattern will come out.

Copyright © LG Electronics. Inc. All right reserved. - 12 - LGE Internal Use Only
Only for training and service purposes
* Manual W/B process using adjusts Remote con- 4.2. DPM test
trol. ■ Measurement Condition: 100 - 240V@ 50/60Hz
■ After enter Service Mode by pushing "ADJ" key, 1) Set Input to RGB-PC and connect D-sub cable to set –
■ Enter White Balance by pushing "►" key at "White Bal- RGB Mode. Set Input to HDMI (with Input Label set to PC)
ance". and connect HDMI cable to set – HDMI Mode
2) Cut off H sync or V sync of signal.
3) Check DPM operation refer to the below table.
Operating Condition Sync Video LED Wattage
(H/V) (SET) (W)
Power S/W On Sleep mode - Off/Off Off Amber 1
RGB,HDMI

4.3. PIP Check

1) Press "Power on" key of service remote control.
2) Input RGB & TV(ATV or DTV) signal.
3) Set Input mode to RGB.
4) Press ‘PIP" key of ADJ remote controller
* CASE Medium Mode 5) Check TV Video & Audio signal of Sub picture.
First adjust the coordinate far away from the target value(x,
y)B
1) x, y > target
2) x, y < target
3) x >target , y < target
4) x < target , y > target
- Every 4 case have to fit y value by adjusting B Gain and then
fit x value by adjusting R-Gain
- In this case, increasing/decreasing of B Gain and R Gain
can be adjusted.

How to adjust
4.4. Outgoing condition Configuration
■ When pressing IN-STOP key by SVC remocon, Red LED
1) If G gain more than 172, adjust R Gain and B Gain less
are blinked alternatively. And then automatically turn off.
than 192
(Must not AC power OFF during blinking)
2) If the G gain value be adjusted down to 172, one of the R/B
Gain is 254
3) If G Gain is 172 , more than one of R/B Gain is to be be-
tween 192~254. 5. Model Name & Serial Number
* CASE Cool / Warm Download
First adjust the coordinate far away from the target value(x, y). 5.1. Model name & Serial number
1) x, y > target ■ Press “Power on” key of service remocon.(Baud rate :
a) Decrease the R, G. 115200 bps)
2) x, y < target ■ Connect USB to RS232 Signal Cable to USB Jack.
a) First decrease the B gain, ■ Write Serial number.
b) Decrease the one of the others. ■ Must check the serial number at the Diagnostics of SET UP
3) x >target , y < target menu. (Refer to below).
a) First decrease B, so make y a little more than the
target.
b) Adjust x value by decreasing the R
4) x < target , y > target
a) First decrease B, so make x a little more than the
target.
b) Adjust x value by decreasing the G

* After You finish all adjustments, Press “In-start” button and

5.2. Signal TABLE
CMD LENGTH ADH ADL DATA_1 ... Data_n CS DELAY
compare Tool option and Area option value with its BOM, if it
is correctly same then unplug the AC cable. If it is not same,
CMD : A0h
then correct it same with BOM and unplug AC cable. For cor-
LENGTH : 85~94h (1~16 bytes)
rect it to the model’s module from factory JIG model.
ADH : EEPROM Sub Address high (00~1F)
* Push The “IN STOP KEY” after completing the function
ADL : EEPROM Sub Address low (00~FF)
inspection. And Mechanical Power Switch must be set “ON”.
Data : Write data
CS: CMD + LENGTH + ADH + ADL + Data_1 + … + Data_n
Delay : 20ms

Copyright © LG Electronics. Inc. All right reserved. - 13 - LGE Internal Use Only
Only for training and service purposes
5.3. Command Set 6.1.2.2. MAC Address & CI+ Key Download
▪ Set CI+ Key path Directory at Start Mac & CI+ Download
No. 1
Programme
Adjust mode EEPROM WRITE ▪ Com 1,2,3,4 and 115200 (Baudrate)
CMD(hex) A0h
LENGTH(hex) 84h+n
Description n-bytes Write (n = 1~16)

* Description
FOS Default write : <7mode data> write
Vtotal, V_Frequency, Sync_Polarity, Htotal, Hstart, Vstart, 0,
Phase
Data write : Model Name and Serial Number write in EE-
PROM.

5.4. Method & notice

1) Serial number D/L is using of scan equipment.
2) Setting of scan equipment operated by Manufacturing
Technology Group.
3) Serial number D/L must be conformed when it is produced
in production line, because serial number D/L is mandatory
by D-book 4.0

* Manual Download (Model Name and Serial Num-

ber) ▪ Port connection button click(1)
If the TV set is downloaded By OTA or Service man, Some- ▪ Push the (2) MAC Address write.
times model name or serial number is initialized.( Not always) ▪ At success Download, check the OK (3)
There is impossible to download by bar code scan, so It need ▪ Start CI+ Key Download, Push the (4)
Manual download. ▪ Check the OK or NG
a. Press the ‘In start’ key of ADJ remote controller.
b. Go to the menu ‘6.Model Number D/L’ like below photo. * Check the Download to CI+ Key value in LG set.
c. Input the Factory model name(ex 32LV3400-ZG) or Serial 1) Check the method of CI+ Key value
number like photo. a) check the method on Instart menu

6. MAC Address & CI+ Key Down-

load
6.1. MAC Address
6.1.1. Equipment & Condition
▪ Play file : Serial.exe
▪ MAC Address edit
▪ Input Start / End MAC address

6.1.2. Download method

6.1.2.1. Communication Prot connection
Connection : PCBA (USB Port) → USB to Serial Adapter (UC-
232A) → RS-232C cable → PC(RS-232C port) 2) Check the method of CI+ Key value (RS232)
a) into the main ass’y mode (RS232 : aa 00 00)
CMD 1 CMD 2 Data 0
A A 0 0
b) check the mothed of CI+ key by command
(RS232 : ci 00 10)
CMD 1 CMD 2 Data 0
C I 1 0
c) result value
OKx : CI+ Key Download OK
NGx : CI+ Key Download NG

Copyright © LG Electronics. Inc. All right reserved. - 14 - LGE Internal Use Only
Only for training and service purposes
 TROUBLE SHOOTING
1. No Power
Check C400 N Check Power connector Y
Replace Adapter
Voltage Level (19V) OK ?

Check IC401 Output N Replace IC401 &

Voltage Level (3.3V) Recheck

Check IC402 Output N Replace IC402 &

Voltage Level (1.15V) Recheck

Check IC403 Output N Replace IC403 &

Voltage Level (5V) Recheck

Y
Check X101 Clock N
Replace X101
24MHz
Y

Replace IC100 Flash

Memory

Copyright © LG Electronics. Inc. All right reserved. - 15 - LGE Internal Use Only
Only for training and service purposes
2. No Screen on
N N
Check IC101
Module Back Light On? Check WLED_ENABLE High? Replace Main SOC

Y
Y

N
Check LED Driver NDRV Check IC1001 & Q1002
(Pin22 of IC 1001) Replace LED Driver IC or FET

N
Check Panel Power 5V (P602 #1) Replace IC403 &
Check IC403 Output 5V Recheck

Check Panel input Clock N Check IC101

P602 (#10, #11 ) Repair Main B/D

Check FFC Cable f or Damage or N

Replace Cable
Open Conductors

Replace T-Con Board or Module

Copyright © LG Electronics. Inc. All right reserved. - 16 - LGE Internal Use Only
Only for training and service purposes
3. No Video - Digital TV
Check RF Cable

1. Check RF IC(L2603) Power (3.3V) N

Replace IC401 & IC2600 Recheck
2. Check IC2600 Output voltage(1.2V) – only 77V Model
Y

N
Check SCL/SDA Line(TU2602 #4, #5) Replace TU2602 or IC101

Copyright © LG Electronics. Inc. All right reserved. - 17 - LGE Internal Use Only
Only for training and service purposes
4. No Video - HDMI
Check input signal format
Is it supported?

Check HDMI Cable for

Damage or Open Connector

N
Check JK800/801 for proper
Replace Connector
connection or Damage
Y

Check I2C Signal N Re Download EDID Data

(JK800/801)

Replace Main Scaler

(IC101)

Copyright © LG Electronics. Inc. All right reserved. - 18 - LGE Internal Use Only
Only for training and service purposes
 BLOCK DIAGRAM

Copyright © LG Electronics. Inc. All right reserved. - 19 - LGE Internal Use Only
Only for training and service purposes
 EXPLODED VIEW
IMPORTANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts
are identified by in the Schematic Diagram and EXPLODED VIEW.
It is essential that these special safety parts should be replaced with the same components as recommended
in this manual to prevent Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.

900
910
925920
400
535
LV1

820

120
A2

540

800
810
200

510
300

502
501

Copyright © LG Electronics. Inc. All right reserved. - 20 - LGE Internal Use Only
Only for training and service purposes
 19V to 3.5V (OPTION : WIFI)
19V to 12V (OPTION : LNB) +3.3V_Normal

R444
MULTI_ON 10K

IC400 C443 WIFI

LNB 0.1uF
MP2315GJ R409 IC405 16V
10K LNB MP2315GJ WIFI
+19V OPT OPT
R402 R418 +12V_Normal WIFI
JK400 JP400 1K AAM FB 33K R443
1 8 1K AAM FB R447 +3.5V_WIFI
KJA-DC-1-0032 1 8 75K

IN VCC L402 1%
4 2 7 10uH L405
IN VCC
LNB 2 7 4.7uH
LNB LNB
2 OPT OPT SW EN/SYNC LNB LNB WIFI
C400 C401 C402 C404 C406 3 6 WIFI WIFI SW EN/SYNC WIFI
R448
47uF 10uF 10uF 2.2uF 0.1uF R421 3 6 1K
25V 25V 25V 25V 50V 43K C441 C442 WIFI
LNB 2.2uF 0.1uF
1 105C GND BST C417 1% 25V 50V 1%
4 5 WIFI C448
JP401 OPT 0.1uF C422 C424 C428 GND BST C445 C446 C447
Check the Ripple LNB 4 5 OPT 22uF 10uF 0.1uF R449
R410 16V 10uF 10uF 0.1uF 0.1uF
2K R422 WIFI R446 6.3V 10V
LNB R406 16V 16V 16V 16V 16V 33K WIFI
68 100K 2K
11.11.07 LNB LNB 1% R445 OPT 1%
LNB 68 WIFI WIFI
6604->6601
C412
LNB LNB
0.1uF C444
50V R423 0.1uF
10K R450
50V
1% 10K
WIFI
WIFI
1%

+3.3V_ST

IC401
+3.3V_ST
MP2315GJ R411 S +3.3V_Normal
R440
100K
22K C439 G
R403 R419 4.7uF
AAM FB 33K +3.3V_ST
47K 1 8 10V
PMV48XP D
Q402
L401
IN VCC R438 C434
2 7 10uH
R401
10K 100
R427 C 1uF
SW EN/SYNC R434
3 6 10V
C405 C407 1.6K 100K B Q400 C438
2.2uF 0.1uF POWER_ON/OFF1 OPT
25V 50V 1% MMBT3904(NXP) 0.1uF
GND BST 16V
4 5 C418 E
C423 C425 C429 R428
R412 0.1uF
22uF 10uF 0.1uF 1.6K
15K 16V
6.3V 10V
R407 16V 1%
68
OPT
C413
0.1uF R429
50V 1K
1%

3.3V TO 1.5V LDO(DDR Power)

+3.3V_Normal +1.5V_DDR
+3.3V_Normal
19V to 1.15V (M1 Core)
R414
10K
C415
0.1uF
IC402 16V IC404
MP2315GJ AZ1117EH-ADJTRG1
OPT
R404 R416 +1.15V_VDDC IN OUT
1K AAM FB 75K
1 8
ADJ/GND R1
1%

1/16W
IN VCC L400

R451
2 7 4.7uH

1K

1%
SW EN/SYNC C449
3 6 R424 10uF
C403 C408 4.7K 10V
2.2uF 0.1uF C450
25V 50V 1%
GND BST C421 C426 C430 10uF
4 5 OPT
C419
22uF 0.1uF
R2
0.1uF 10uF R425 10V
R413 6.3V 10V 16V

1/16W
2K 16V 0

R452
200
R408 OPT 5%

1%
68

C414 Vout = 1.25*(1+R2/R1) + Iadj*R2

0.1uF R426
50V
10K
1%

PANEL POWER CONTROL

19V TO 5V DCDC CONVERTER +5V_Normal
+5V_PANEL_POWER
D400
MULTI_ON MMBD6100
A2 R400
C 10K
LED_AMBER PMV48XP
A1 Q403
C410

D
0.47uF

1K

R456
16V

1uF OPT
OPT C R441
R463
4.7K

G
B Q404 100K C440

C436

16V
IC403 4.7uF
MP2315GJ 16V
+5V_Normal MMBT3904(NXP) E R457
OPT
0
R405 R420
1K AAM FB 33K
1 8
R442
L403 10K
IN VCC 10uH
2 7
C
PANEL_CTL R436
C409 SW EN/SYNC R430 4.7K B Q401
2.2uF C411 3 6 47K
25V 0.1uF MMBT3904(NXP)
50V 1% R439
GND BST 10K E
4 5 C420
OPT C427 C431 C432 R431
0.1uF
R417
2K
16V 10uF 10uF 0.1uF 8.2K Change 5V --> 5.2V
R415 10V 10V 16V 1%
68 Because MT75D issue
C416
0.1uF R432
50V
10K Vout = (((47+8.2)/10)+1)*0.8
1%

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS MT77 2013/10/03
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. POWER 4

Copyright ⓒ 2015 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes
 Module(FHD)
P602
+5V_PANEL_POWER 10031HR-30

1
5.6K

C602 JP614 2
5.6K
R615

R616

0.1uF
16V 3

4
For Interlace Mode
High : Interlace Mode
5
Low : Normal Mode Option Delete
2013.07.15
6

RXA3+ 8

RXA3- 9

RXACK+ 10

RXACK- 11

RXA2+ 12

RXA2- 13

14

RXA1+ 15

RXA1- 16

17

RXA0+ 18

RXA0- 19

RXB3+ 20

RXB3- 21

RXBCK+ 22

RXBCK- 23

24

RXB2+ 25

RXB2- 26

RXB1+ 27

RXB1- 28

RXB0+ 29

RXB0- 30

31

JP613

IR_OUT(Ready)
IR/LED and Control +3.3V_ST TOUCH KEY JOYSTICK
P601 P603
+3.3V_ST
12507WR-12L 12507WR-08L

OPT OPT OPT

R613 R618
D600 D601
3.3K JP601 1 10K
30V 30V 1 +3.3V_ST
OPT
R614 R617 R619
R611 22 0
3.3K
100 JP602 2 IR_OUT
KEY2 2
OPT
R612 C OPT R621
100 R620 10K
JP603 3 3 10K
KEY1 Q602 B OPT
MMBT3904(NXP)
Close to Wafer OPT
JP606 4 E C603
4 1000pF
TOUCH KEY 50V
R623 OPT C
22 R622
JP605 5 5 47K
KEY_SCL Q603 B
+3.3V_ST +3.3V_ST IR
MMBT3904(NXP) OPT
R624 OPT
22 JP604 6 E
KEY_SDA 6
Red LED(M75) : 5.9mA TOUCH KEY
TOUCH KEY
R610 270 7 7
Amber LED(M75) : 16mA
1/10W
TOUCH KEY JP608
R606 100 8 8
1/10W
JP607 9
9

JP609
R600 C 10
10K (IR Port protection against ESD)
B Q600 121018 R609
LED_RED JP610
MMBT3904(NXP) 100ohm->200ohm 200
IR 11
R601
10K

E
OPT

+3.3V_ST JP611
12
50V

JP612 13
20V
1000pF
C601

VA600

R602 C
10K B
LED_AMBER Q601
MMBT3904(NXP)
4.7K
R603

E
OPT

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS MT77 2013/10/03
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. IR/CONTROL/MODULE 6

Copyright ⓒ 2015 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes
 DSUB RGB D700
+5V_Normal
USB(SIDE) +5V_Normal
DSUB/SCART Switch +5V_Normal

MMBD6100
A2 MAX 1.5A(USB 2.0) EU
C EU EU
OPT
IC701 C711 IC702 C722 C725 C733
A1 EU 0.01uF 0.1uF 22uF 22uF
BD2242G
25V BA7657F 10V 10V
EU C710
6.3V
VOUT VIN DSUB_R+ 22uF
6 1 RED_1_INPUT HD_1_INPUT
1 24 DSUB_HSYNC
R705 R708 C708 C709
10K C705 C723 ILIM GND 470pF
10K ZD702 5 2 0.1uF C713 50V HD_SYNC_SIGNAL_DETECTOR HD_2_INPUT
22uF 10uF EU 0.01uF 2 23
5V 16V 25V
RGB_DDC_SCL OPT 10V
OPT OC EN EU C714
4 3 6.3V R727 470KGREEN_1_INUT HD_OUTPUT
RGB_DDC_SDA DSUB_G+ 22uF 3 22 DSUB/SC1_HSYNC
USB_CTL
R725 +3.3V_Normal
R726 10K GROUND1 RED_OUTPUT R715
14K EU C716 4 21 DSUB/SC1_R+
VA707 0.01uF
75 EU

4.7K
25V
20V

R740
130529 3AU04S-305-ZC-(LG) EU C717 BLUE_1_INPUT VCC
DSUB_VSYNC/HSYNC Pull-Down 121128 6.3V 5 20
JK701 DSUB_B+ 22uF R714 R728
ESD improve

EU

EU
121128
OPT->APPLY ESD improve 68K 2K R729
GROUND2 GREEN_OUTPUT 75

1
OPT->APPLY 6 19 DSUB/SC1_G+

USB DOWN STREAM

JP713 USB_OCD EU
DSUB_VSYNC VA700 VA701 C719
121128 EU 0.01uF
2:E18 20V 20V ESD improve 25V RED_2_INPUT COMPOSITE_VIDEO_INPUT

2
121128 USB_DM 1:AL8 7 18
DSUB_HSYNC OPT->APPLY
2:E18 ESD improve C720
+3.3V_ST EU 6.3V
OPT->APPLY SC1_R+ 22uF
R731 R732 JP712 GROUND3 COMPOSITE_SYNC_OUTPUT

3
2.4K 10K VA710 USB_DP 1:AL7 8 17
JP700 20V
JP701 R712
JP711 111026 C727 GREEN_2_INPUT CONTROL 22 EU

4
R713
VA712 VA716 EU 0.01uF 9 16

47K
JP707 20V 20V ESD diode deletion 25V

5
JP709 EAH39491601 2EA
R710 EU
C728 R716
47K SC1_G+ 6.3V GROUND4 BLUE_OUTPUT 75
DSUB_DET 121128 120103 22uF 10 15 DSUB/SC1_B+
DSUB_B+ 121128
C ESD improve ESD improve ESD diode addition EU
JP705 Q700 OPT->APPLY OPT->APPLY EAF61530301 2EA
R700 R711 B BLUE_2_INPUT VD_OUTPUT
75 MMBT3904(NXP) 11 14
EU C730 DSUB/SC1_VSYNC
10K 0.01uF
VA711 25V
JP703 20V E VD_1_INPUT VD_2_INPUT
DSUB_G+ EU C731 12 13
6.3V SC1_FB
SC1_B+ 22uF
R701
GREEN_GND

DDC_CLOCK
DDC_DATA

BLUE_GND

SYNC_GND

75 121128
RED_GND

DDC_GND
H_SYNC

V_SYNC

+3.3V_ST
GND_2

GREEN

GND_1

ESD improve
BLUE
RED

JP704
NC

OPT->APPLY
JP710

DSUB_R+
DSUB_VSYNC

EU
R733
SHILED
11

12

13

14

15

R702 10K
75
PC AUDIO(SIDE)
16
10
6

11.10.31
To Improve EMI R734 EU
1

DSUB_R+ DSUB/SC1_R+ C
33 R730 Q701
5.5V

5.5V
VA703

VA705

VA706

EU_NOT
5.5V

4.7K B MMBT3904(NXP)
R735
JK703 DSUB/SC1_OUT_CTRL
DSUB_G+ 33 DSUB/SC1_G+
SPG09-DB-010
+3.3V_Normal R736EU_NOT EU
E
DSUB_B+ 33 DSUB/SC1_B+
R737EU_NOT
11.10.27
DSUB_HSYNC 0 DSUB/SC1_HSYNC
To Improve Ringing issue
12.08.10 R721 R738EU_NOT
LOW capacitance Part apply 470K
47K->470K R724 DSUB_VSYNC 0 DSUB/SC1_VSYNC
1K EU_NOT
PC_AUDIO_DET

JP715 VA715
20V
OPT
R719
15K

6 M6 OPT
PC_R_IN ETHERNET
JP718 VA713 C707 R718 R722
20V 220pF 470K 10K 14.07.03 by HAN
1 M1 OPT
50V LAN Jack deletion for SPDIF.

3 M3_DETECT
RS232C(SIDE) Hotel_Model(RS232C apply)
C700 +3.3V_ST
R720
15K
0.33uF PC_L_IN
16V 4 M4
Hotel_Model(RS232C apply)
OPT
JP717 R717
VA714 C706 470K
Hotel_Model(RS232C apply) C702 5 M5_GND R723
0.33uF 20V 220pF 10K
C701 OPT
16V KJA-PH-1-0177 50V
0.33uF
16V JK702 JP716
C703
0.1uF
16V
Hotel_Model(RS232C apply)
DOUT2
RIN2

C2-

C2+

C1-

C1+
V-

V+
8

IC700

MAX3232CDR

Hotel_Model(RS232C apply) 120918

JIG GND Point addition
10

11

12

13

14

15

16
9
ROUT2

DIN2

DIN1

ROUT1

RIN1

DOUT1

GND

VCC

Hotel_Model(RS232C apply)
R703
0 C704
0.1uF JP714 JP719 JP720 JP721
Hotel_Model_NOT(RS232C Bypass) 16V +3.3V_ST
PM_TXD R704 SW DEBUG Wafer
0 P701
R707
PM_RXD 100 VA708
Hotel_Model_NOT(RS232C Bypass) 20V 12507WS-04L
R706
100
VA702 VA704 1
20V 20V
OPT OPT VA709
20V 2

JP706 JP708
JP702 4
(OPT)IR_OUT
IR_OUT 5
Jack Shield (HDMI1, HDMI2, RGB)
M3_DETECT

R709
0
M5_GND

M4

M1

M6

SPDIF_OPTIC
5

6
KJA-PH-1-0177

+3.3V_Normal JK705
JackShield(for NonCKD) JackShield(for CKD) SPDIF JST1223-001
JK700

M700 M700-*1
MGJ63348201

1
MGJ63348202

Fiber Optic
GND

2
Hotel_Model(RS232C apply) VCC

3
SPDIF_OUT
VINPUT

4
SPDIF_OPTIC
C736 C737
0.1uF 18pF FIX_POLE
16V 50V
SPDIF_OPTIC

ESD Ready

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS MT77 2013/10/01
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. INTERFACE 7

Copyright ⓒ 2015 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes
 HDMI
HDMI_1
+3.3V_ST CEC
R823
100
R809
47K

HDMI_CEC CEC_REMOTE_S7
R802
47K

5V_DET_HDMI_1
C
R805 Q800
10K B MMBT3904(NXP)

OPT E
5V_HDMI_1 VA804 5V_HDMI_1 +5V_Normal 5V_HDMI_2 +5V_Normal +3.3V_ST

A1

A2

A1

A2

A1

A2
GND
R801 MMBD6100 MMBD6100 MMBD6100
D804 D806 D807
20 1K

C
C MHL
R812
Q802 B 10K
19 OPT HPD1
HP_DET OPT MMBT3904(NXP)
VA809
18 20V
5V VA803 E 120915
R819 R820
17 20V R824 R825 47K->2.7K
GND
DDC_SDA_1 2.7K 2.7K 2.7K 2.7K
16
DDC_DATA
DDC_SCL_1 DDC_SDA_1 DDC_SDA_2
15
DDC_CLK R804 0
HDMI_ARC
14 OPT VA812 VA814
NC HDMI_CEC DDC_SCL_1 DDC_SCL_2
20V 20V
13 OPT OPT
CE_REMOTE
VA800 VA806
12 20V 20V
EAG59023302

CK- (OPT)ESD_HDMI_SEMTECH(DEV)
D800 120715
11
CK_GND 5.1 RCLAMP0524PA Added for ESD prevention
1 10 120825
10
CK+ 2 9 CK-_HDMI1 OPT->APPLY
9 CK+_HDMI1
3 8
D0-
4 7
8 D0-_HDMI1
D0_GND 5 6
AR800 D0+_HDMI1
7 120825
D0+
ESD component addition
6
D1- (OPT)ESD_HDMI_SEMTECH(DEV)
D800-*1 D801-*1
5 D801 IP4283CZ10-TBA IP4283CZ10-TBA
D1_GND 5.1
4
D1+
1
2
RCLAMP0524PA
10
9
D1-_HDMI1
TMDS_CH1-
1 10
NC_4 TMDS_CH1-
1 10
NC_4 MHL OCP
D1+_HDMI1 TMDS_CH1+
2 9
NC_3 TMDS_CH1+
2 9
NC_3
3 3 8
D2- GND_1 GND_2 GND_1 GND_2
4 7 3 8 3 8
2 D2-_HDMI1
D2_GND 5 6 TMDS_CH2-
4 7
NC_2 TMDS_CH2-
4 7
NC_2

AR801 D2+_HDMI1
1 TMDS_CH2+ NC_1 TMDS_CH2+ NC_1
D2+ 5 6 5 6

(OPT)ESD_HDMI_NXP (OPT)ESD_HDMI_NXP MHL

AVDD5V_MHL 5V_HDMI_2 IC800
YKF45-7058V BD82020FVJ +5V_Normal
JK801 +3.3V_Normal
MHL
D805
MBR230LSFT1G OUT_3 GND
8 1 R816 MHL
R818 30V 0
10 C801 100K OUT_2 IN_1
121109 10uF OPT 7 2
10V R822
HDMI_2 With MHL Change 0ohm -> 10ohm MHL
(EOS Issue..Mstar Recommand) OUT_1
6 3
IN_2
C802
0.1uF
MHL
R828
10K
R829
2.7K
MHL MHL
16V
OC EN

E
+3.3V_ST 5 4
+3.3V_Normal
Q806
MHL C
R830

B
B 10K
R821 R826 /VBUS_EN
10K 20K MHL
R810

/MHL_OCP_DET MHL MHL R827 Q808 (Active Low)

47K

E
10K MHL
R803
47K

MHL
5V_DET_HDMI_2 C
C R831
R806 Q801 B 10K
10K B MMBT3904(NXP) MHL_OCP_EN
MHL
Q807 (Active High)
E
OPT E MHL
5V_HDMI_2 VA805

R811
33
OPT
GND
R800
OPT
20 1K C
OPT R814
Q803 B 10K
19 MMBT3904(NXP) HPD2
HP_DET OPT
VA808
18 OPT E
5V 20V
VA802
17 20V
GND
DDC_SDA_2
16
DDC_DATA
DDC_SCL_2
15
DDC_CLK R807 0
HDMI_ARC
14 OPT
NC VA811 VA813
HDMI_CEC 20V 20V
13 OPT OPT
CE_REMOTE
VA801 VA807
12 20V (OPT)ESD_HDMI_SEMTECH(DEV)
EAG59023302

20V
CK- D802 120715
R832 RCLAMP0524PA Added for ESD prevention
11 SIGN1500176BBB
5.1
CK_GND 1 10 120825
2 9 CK-_HDMI2 OPT->APPLY
10
CK+ CK+_HDMI2 D802-*1 D803-*1
5.1 3 8 IP4283CZ10-TBA IP4283CZ10-TBA
9 R833
D0- 4 7 TMDS_CH1- NC_4 TMDS_CH1- NC_4
D0-_HDMI2 1 10 1 10

8 5 6
D0_GND D0+_HDMI2 TMDS_CH1+
2 9
NC_3 TMDS_CH1+
2 9
NC_3

120825
7 ESD component addition
GND_1
3 8
GND_2 GND_1
3 8
GND_2
D0+
6 (OPT)ESD_HDMI_SEMTECH(DEV) TMDS_CH2-
4 7
NC_2 TMDS_CH2-
4 7
NC_2

D1- D803
5.1 RCLAMP0524PA
TMDS_CH2+
5 6
NC_1 TMDS_CH2+
5 6
NC_1
5
SIGN1500176A
D1_GND 1 10 (OPT)ESD_HDMI_NXP (OPT)ESD_HDMI_NXP
D1-_HDMI2
4 2 9
D1+ D1+_HDMI2
3 8
3
D2- 4 7
D2-_HDMI2
2 5 6
D2_GND AR802 D2+_HDMI2
1
D2+
MHL_NOT MHL
R808 R813
0 0
YKF45-7058V MHL_CD_SENSE
JK800
VA810

C800 R817
5.6V

0.047uF
OPT

25V 300K

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS MT77 2013/09/16
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. HDMI 8

Copyright ⓒ 2015 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes
 +19V
L1001
33uH
D1001

BR210
100V

+19V
D
Q1002
WLED_ENABLE G AOD478
IC1001
R1023 C1020
100K
DT1641AS [EP]GND S
100pF
1% 50V
EN VIN
1 24 C1023
1uF

THERMAL
R1020 25V
C1022

25
510K OVP VREF
2 23
1/8W 1uF
1% C1021 NC_1 CS 25V
R1022 3 22
22K 1000pF
1% 50V
PGND_1 NDRV
4 21
R1016
100 R1039
PGND_2 RSS R1037
5 20
WLED_DIM_ADJ R1019 C1019 30K 1%
100pF 220K 1%
100K 50V C1024
1% PDIM COMP
6 19
4700pF
R1021 50V
100K RISET RT
7 18
BLU_CURRENT_CTL
1% LS8 LS1
R1038 C1025

0.1
R1044
8 17

1%
R1024
1.5K 1.5K 1% 0.047uF
1% LS7 LS2 25V
9 16
R1025 R1035
33K LS6 LS3 39K
1% 10 15
1%

LS5 LS4 R1036

11 14 1.5K
1%
NC_2 LGND
12 13

REDUCE RIPPLE CURRENT

CIC21J501NE

L100 500

C1026
C1027
33uF 33uF
100V 100V
-55TO+105C -55TO+105C

7
7
M1004
6
6
M1005
5
5
M1006
4
4
3
3
M1007
2
23.8 LGD
0

2
M1008
R1057

1
1

12507WR-06L
12507WR-06L P1005
P1004 OPT
0
23 LGD
R1056

LED Driver Setting

23 inch LGD Panel : LED_CH3 SET

23.8 inch LGD Panel : LED_CH2 SET
27 inch LGD Panel : NO SETTING

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS MT77 2013/10/01
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. LED DRIVER 10

Copyright ⓒ 2015 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes
 +1.5V_DDR +1.5V_DDR

+1.5V_DDR +1.5V_DDR
R1204
R1201

1K 1%
1K 1%

A-MVREFDQ A-MVREFCA
1000pF 50V
1%

0.1uF 16V

1000pF 50V

0.1uF 16V

0.1uF 16V

0.1uF 16V

1uF 10V

1uF 10V

1uF 10V

1uF 10V

1uF 10V

0.1uF 16V
1%

C1217

C1218

C1219

C1238

C1241
R1202

R1205

C1206

C1239

C1220
10uF10V
C1201

C1202

C1251
C1203

C1204

OPT

OPT

OPT

OPT

OPT

OPT
1K

1K

CLose to DDR3 CLose to Saturn7M IC

DDR_1866_1G_SS
IC1201 128M_SCALER 256M_SCALER
K4B1G1646G-BCMA IC101 IC101-*1
LGE2133(128M) LGE2134(256M)
M8 N3
A-MVREFCA VREFCA A0 A-MA0
P7
A1 A-MA1 E11 E11
P3 A-MA0 B_DDR3_A[0] B_DDR3_A[0]
A2 A-MA2 F12 F12
H1 N2 A-MA1 B_DDR3_A[1] B_DDR3_A[1]
A-MVREFDQ VREFDQ A3 A-MA3 D10 D10
P8 A-MA2 B_DDR3_A[2] B_DDR3_A[2]
A4 A-MA4 B10 B10
P2 A-MA3 B_DDR3_A[3] B_DDR3_A[3]
R1203 A5 A-MA5 E15 E15
L8 R8 A-MA4 B_DDR3_A[4] B_DDR3_A[4]
ZQ A6 A-MA6 B11 B11
240 R2 A-MA5 B_DDR3_A[5] B_DDR3_A[5]
+1.5V_DDR A7 A-MA7 F14 F14
1% T8 A-MA6 B_DDR3_A[6]
A8 A-MA8 C11 B_DDR3_A[6]
B2 R3 A-MA7 B_DDR3_A[7] C11
VDD_1 A9 A-MA9 D14 B_DDR3_A[7]
10V C1205 D9 L7 A-MA8 B_DDR3_A[8] D14
10uF A-MA10 A12 B_DDR3_A[8]
VDD_2 A10/AP A12
16V C1207 0.1uF G7 R7 A-MA9 B_DDR3_A[9]
VDD_3 A11 A-MA11 F16 B_DDR3_A[9]
K2 N7 A-MA10 B_DDR3_A[10] F16
16V C1208 0.1uF A-MA12 D13 B_DDR3_A[10]
VDD_4 A12/BC D13
16V C1210 0.1uF K8 T3 A-MA11 B_DDR3_A[11] B_DDR3_A[11]
VDD_5 A13 A-MA13 D15 D15
16V C1211 0.1uF N1 A-MA12 B_DDR3_A[12] B_DDR3_A[12]
VDD_6 C12 C12
16V C1212 0.1uF N9 M7 A-MA13 B_DDR3_A[13]
VDD_7 NC_5 E13 B_DDR3_A[13]
16V C1213 R1 A-MA14 E13
0.1uF B_DDR3_A[14] B_DDR3_A[14]
VDD_8
16V C1214 0.1uF R9 M2
VDD_9 BA0 A-MBA0 A-MCK A9 A9
R1235

16V C1215 0.1uF N8 A-MBA0 B_DDR3_BA[0]

A-MBA1 D16 B_DDR3_BA[0]
1%

BA1 D16
M3 A-MBA1 B_DDR3_BA[1]
56

16V C1216 0.1uF A-MBA2 A10 B_DDR3_BA[1]

BA2 A10
A1 C1209 A-MBA2 B_DDR3_BA[2]
VDDQ_1 B_DDR3_BA[2]
R1236

A8 J7
0.01uF C13
1%

VDDQ_2 CK C13
C1 K7 50V A-MCK B_DDR3_MCLK
56

VDDQ_3 CK B13 B_DDR3_MCLK

C9 K9 A-MCKB B13
B_DDR3_MCLKZ B_DDR3_MCLKZ
VDDQ_4 CKE A-MCKE E17 E17
D2 A-MCKE B_DDR3_MCLKE
VDDQ_5 A-MCKB B_DDR3_MCLKE
E9 L2
VDDQ_6 CS A/B_DDR3_CS B8 B8
F1 K1 A-MODT B_DDR3_ODT
VDDQ_7 ODT A-MODT C8 B_DDR3_ODT
H2 J3 A-MRASB C8
B_DDR3_RASZ B_DDR3_RASZ
VDDQ_8 RAS A-MRASB +1.5V_DDR B9 B9
H9 K3 A-MCASB B_DDR3_CASZ
VDDQ_9 CAS A-MCASB R1231 D11 B_DDR3_CASZ
L3 A-MWEB D11
A-MDQSU
A-MDQSL

B_DDR3_WEZ B_DDR3_WEZ
WE A-MWEB 10K
J1
NC_1 F10 F10
J9 T2 A-MRESETB B_RESET
A-MDQSUB
A-MDQSLB

NC_2 RESET A-MRESETB B_RESET

L1
NC_3 D12 D12
L9 A/B_DDR3_CS B_DDR3_CS0
NC_4 B_DDR3_CS0
T7 F3
A-MA14 NC_6 DQSL A-MDQSL A19 A19
G3 B_DDR3_DQSL
DQSL A-MDQSLB B18 B_DDR3_DQSL
B18
B_DDR3_DQSU B_DDR3_DQSU
A9 C7
VSS_1 DQSU A-MDQSU C16 C16
B3 B7 A-MDML B_DDR3_DQML
VSS_2 DQSU A-MDQSUB D21 B_DDR3_DQML
E1 A-MDMU D21
B_DDR3_DQMU B_DDR3_DQMU
VSS_3
G8 E7
VSS_4 DML A-MDML C18 C18
J2 D3 B_DDR3_DQSBL
VSS_5 DMU A-MDMU C17 B_DDR3_DQSBL
J8 C17
B_DDR3_DQSBU B_DDR3_DQSBU
VSS_6
M1 E3
VSS_7 DQL0 A-MDQL0 A20 A20
M9 F7 A-MDQL0 B_DDR3_DQL[0]
VSS_8 DQL1 A-MDQL1 A16 B_DDR3_DQL[0]
P1 F2 A-MDQL1 A16
B_DDR3_DQL[1] B_DDR3_DQL[1]
VSS_9 DQL2 A-MDQL2 C19 C19
P9 F8 A-MDQL2 B_DDR3_DQL[2]
VSS_10 DQL3 A-MDQL3 C15 B_DDR3_DQL[2]
T1 H3 A-MDQL3 C15
B_DDR3_DQL[3] B_DDR3_DQL[3]
VSS_11 DQL4 A-MDQL4 C20 C20
T9 H8 A-MDQL4 B_DDR3_DQL[4]
VSS_12 DQL5 A-MDQL5 C14 B_DDR3_DQL[4]
G2 A-MDQL5 C14
B_DDR3_DQL[5] B_DDR3_DQL[5]
DQL6 A-MDQL6 B21 B21
H7 A-MDQL6 B_DDR3_DQL[6]
DQL7 A-MDQL7 B15 B_DDR3_DQL[6]
B1 A-MDQL7 B_DDR3_DQL[7] B15
VSSQ_1 F18 B_DDR3_DQL[7]
B9 D7 A-MDQU0 B_DDR3_DQU[0] F18
VSSQ_2 DQU0 A-MDQU0 D19 B_DDR3_DQU[0]
D1 C3 A-MDQU1 B_DDR3_DQU[1] D19
VSSQ_3 DQU1 A-MDQU1 D17 B_DDR3_DQU[1]
D8 C8 A-MDQU2 B_DDR3_DQU[2] D17
VSSQ_4 DQU2 A-MDQU2 E21 B_DDR3_DQU[2]
E2 C2 A-MDQU3 E21
B_DDR3_DQU[3] B_DDR3_DQU[3]
VSSQ_5 DQU3 A-MDQU3 E19 E19
E8 A7 A-MDQU4 B_DDR3_DQU[4]
VSSQ_6 DQU4 A-MDQU4 D20 B_DDR3_DQU[4]
F9 A2 A-MDQU5 D20
B_DDR3_DQU[5] B_DDR3_DQU[5]
VSSQ_7 DQU5 A-MDQU5 D18 D18
G1 B8 A-MDQU6 B_DDR3_DQU[6]
VSSQ_8 DQU6 A-MDQU6 F20 B_DDR3_DQU[6]
G9 A3 A-MDQU7 B_DDR3_DQU[7] F20
VSSQ_9 DQU7 A-MDQU7 B_DDR3_DQU[7]
R1237
E9 E9
ZQ ZQ
240
1%

DDR_1600_1G_HYNIX
DDR_1866_1G_NANYA
IC1201-*1 IC1201-*2
H5TQ1G63EFR-PBC NT5CB64M16FP-EK
EAN61829003
N3 M8 N3 M8
A0 VREFCA A0 VREFCA
P7 P7
A1 A1
P3 P3
A2 A2
N2 H1 N2 H1
A3 VREFDQ A3 VREFDQ
P8 P8
A4 A4
P2 P2
A5 A5
R8 L8 R8 L8
A6 ZQ A6 ZQ
R2 R2
A7 A7
T8 T8
A8 A8
R3 B2 R3 B2
A9 VDD_1 A9 VDD_1
L7 D9 L7 D9
A10/AP VDD_2 A10/AP VDD_2
R7 G7 R7 G7
A11 VDD_3 A11 VDD_3
N7 K2 N7 K2
A12/BC VDD_4 A12/BC VDD_4
T3 K8 T3 K8
NC_7 VDD_5 NC_6 VDD_5
N1 N1
VDD_6 VDD_6
M7 N9 M7 N9
NC_5 VDD_7 NC_5 VDD_7
R1 R1
VDD_8 VDD_8
M2 R9 M2 R9
BA0 VDD_9 BA0 VDD_9
N8 N8
BA1 BA1
M3 M3
BA2 BA2
A1 A1
VDDQ_1 VDDQ_1
J7 A8 J7 A8
CK VDDQ_2 CK VDDQ_2
K7 C1 K7 C1
CK VDDQ_3 CK VDDQ_3
K9 C9 K9 C9
CKE VDDQ_4 CKE VDDQ_4
D2 D2
VDDQ_5 VDDQ_5
L2 E9 L2 E9
CS VDDQ_6 CS VDDQ_6
K1 F1 K1 F1
ODT VDDQ_7 ODT VDDQ_7
J3 H2 J3 H2
RAS VDDQ_8 RAS VDDQ_8
K3 H9 K3 H9
CAS VDDQ_9 CAS VDDQ_9
L3 L3
WE WE
J1 J1
NC_1 NC_1
T2 J9 T2 J9
RESET NC_2 RESET NC_2
L1 L1
NC_3 NC_3
L9 L9
NC_4 NC_4
F3 T7 F3 T7
DQSL NC_6 DQSL NC_7
G3 G3
DQSL DQSL

C7 A9 C7 A9
DQSU VSS_1 DQSU VSS_1
B7 B3 B7 B3
DQSU VSS_2 DQSU VSS_2
E1 E1
VSS_3 VSS_3
E7 G8 E7 G8
DML VSS_4 DML VSS_4
D3 J2 D3 J2
DMU VSS_5 DMU VSS_5
J8 J8
VSS_6 VSS_6
E3 M1 E3 M1
DQL0 VSS_7 DQL0 VSS_7
F7 M9 F7 M9
DQL1 VSS_8 DQL1 VSS_8
F2 P1 F2 P1
DQL2 VSS_9 DQL2 VSS_9
F8 P9 F8 P9
DQL3 VSS_10 DQL3 VSS_10
H3 T1 H3 T1
DQL4 VSS_11 DQL4 VSS_11
H8 T9 H8 T9
DQL5 VSS_12 DQL5 VSS_12
G2 G2
DQL6 DQL6
H7 H7
DQL7 DQL7
B1 B1
VSSQ_1 VSSQ_1
D7 B9 D7 B9
DQU0 VSSQ_2 DQU0 VSSQ_2
C3 D1 C3 D1
DQU1 VSSQ_3 DQU1 VSSQ_3
C8 D8 C8 D8
DQU2 VSSQ_4 DQU2 VSSQ_4
C2 E2 C2 E2
DQU3 VSSQ_5 DQU3 VSSQ_5
A7 E8 A7 E8
DQU4 VSSQ_6 DQU4 VSSQ_6
A2 F9 A2 F9
DQU5 VSSQ_7 DQU5 VSSQ_7
B8 G1 B8 G1
DQU6 VSSQ_8 DQU6 VSSQ_8
A3 G9 A3 G9
DQU7 VSSQ_9 DQU7 VSSQ_9

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS MT77 2013/10/03
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. M1A-DDR(1EA) 12

Copyright ⓒ 2015 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes
 CI Region * Option name of this page : CI_SLOT
(because of Hong Kong)

CI SLOT +5V_CI_ON

CI_DATA[0-7]

CI TS INPUT

CI_SLOT

CI_DATA[0-7]
CI_SLOT
+5V_Normal
C1904
10uF AR1903 33
10V P1900 FE_TS_DATA[7]
CI_MDI[7]
R1908 EAG41860102 FE_TS_DATA[6]
CI_SLOT

FE_TS_DATA[0-7]
10K CI_MDI[6]
10067972-000LF FE_TS_DATA[5]
CI_MDI[5]
/CI_CD1 CI_SLOT CI_SLOT FE_TS_DATA[4]
CI_MDI[4]
CI_SLOT
R1915 35
100 AR1904 33
36 CI_DATA[3] FE_TS_DATA[3]
CI_MDI[3]
AR1900

CI_DATA[0-7]
37 3 CI_DATA[4] FE_TS_DATA[2]
33 R1919 CI_MDI[2]

CI_SLOT
38 4 CI_DATA[5] 10K FE_TS_DATA[1]
CI_TS_DATA[4] CI_MDI[1]
39 5 CI_DATA[6] CI_SLOT FE_TS_DATA[0]
CI_TS_DATA[5] CI_MDI[0]
CI_SLOT
40 6 CI_DATA[7]
CI_TS_DATA[6]
CI_SLOT R1917 47 CI_SLOT FE_TS_DATA[0-7]
CI_TS_DATA[7] 41 7 /PCM_CE
42 8 CI_ADDR[10] CI_SLOT
R1921 33
R1910 10K CI_MISTRT FE_TS_SYNC
43 9 CI_OE R1922 33
CI_SLOT
CI_SLOT CI_ADDR[11] CI_MIVAL_ERR FE_TS_VAL_ERR
CI_IORD 44 10 R1923 100
CI_ADDR[9] +5V_Normal FE_TS_CLK
CI_IOWR 45 11 CI_MCLKI
46 12 CI_ADDR[8]
CI_ADDR[13] R1920
CI_MDI[0] 47 13 10K 120915
48 14 CI_SLOT CI_ADDR[14] ADDED
CI_MDI[1] CI_SLOT
CI_MDI[2] 49 15 CI_WE
16V

50 16 R1918 100
CI_MDI[3] /PCM_IRQA
CI_SLOT

CI_SLOT
51 17 CI_SLOT

C1902 52 18 C1905 C1906 IC1902-*1

GND 0.1uF 0.1uF 0.1uF 120915 TC74LCX244FT

120915 53 19 ADDED

+5V_Normal
ADDED
CI_MDI[4]
CI_MDI[5] 54 20
GND
CI_ADDR[12]
16V
CI HOST I/F 1OE

1A1
1

2
20

19
VCC

2OE

CI_MDI[6] CI_SLOT
55 21 CLOSE TO MSTAR 2Y4
3 18
1Y1

R1900 56 22 CI_ADDR[7] GND

CI_MDI[7] CI_SLOT +3.3V_Normal 1A2 2A4
10K R1911 10K CI_ADDR[6]
4 17
57 23
CI_SLOT CI_SLOT
R1903 47
2Y3
5 16
1Y2

58 24 CI_ADDR[5]
PCM_RST CI_BUFFER (MAIN) 1A3
6 15
2A3

R1904 47 59 25 CI_ADDR[4]
/PCM_WAIT CI_SLOT IC1902 2Y2 1Y3

CLOSE TO MSTAR REG 60 26 CI_ADDR[3] CI_DET

7 14

CI_SLOT
R1905 100 CI_ADDR[2]
74LCX244FT CI_SLOT 1A4
8 13
2A2

CI_TS_CLK 61 27
CI_SLOT
R1906 33 C1907 2Y1
9 12
1Y4

CI_TS_VAL 62 28 CI_ADDR[1]
0.1uF GND
10 11
2A1
R1907 33 63 29 CI_ADDR[0] 1OE VCC 16V
CI_TS_SYNC
CI_DATA[0] 1 20
64 30
AR1901 33 CI_DATA[1] CI_BUFFER (SUB)
65 31 CI_ADDR[0-14]
CI_TS_DATA[0] CI_DATA[2] 1A1 2OE CI_SLOT
66 32 PCM_A[0] 2 19
CI_TS_DATA[1] 67 33 AR1902 AR1910
CI_TS_DATA[2] 33 33
CI_SLOT 68 34 CI_SLOT
2Y4 1Y1
CI_TS_DATA[3] CI_ADDR[7] 3 18 CI_ADDR[0]
CI_SLOT 2
G2 69 G1
1 CI_ADDR[6] CI_ADDR[1]
R1913 1A2 2A4
100 CI_ADDR[5] 4 17 CI_ADDR[2]
PCM_A[1] PCM_A[7]
/CI_CD2 CI_ADDR[4] CI_ADDR[3]
+5V_Normal GND
2Y3 1Y2
5 16
CI_SLOT
GND
C1900 CI_SLOT 1A3 2A3
2pF 6 15
R1909 PCM_A[2] PCM_A[6]
50V
10K CI_SLOT GND
CLOSE TO MSTAR 2Y2 1Y3
C1901 7 14
0.1uF
16V
1A4 2A2
PCM_A[3] 8 13 PCM_A[5]
CI_MISTRT
CI_MIVAL_ERR 2Y1 1Y4
9 12

CI_MCLKI GND 2A1

10 11 PCM_A[4]

CI DETECT
+3.3V_Normal +3.3V_Normal
CI_DETECT (MAIN)
IC1900
TOSHIBA ELECTRONICS KOREA CORPORATION AR1905 33
CI_DATA[0] PCM_D[0]
IN_B VCC
/CI_CD2 1 5 CI_DATA[1] PCM_D[1]

CI_DATA[0-7]
IN_A CI_DATA[2] PCM_D[2]
/CI_CD1 2 R1912
CI_SLOT

10K CI_DATA[3] PCM_D[3]

GND
3 4
OUT_Y CI_SLOT

PCM_D[0-7]
CI_DETECT (SUB)
IC1900-*1
74LVC1G32GW AR1906 33
CI_DATA[4] PCM_D[4]
CI_DET
B 1 5 VCC CI_DATA[5] PCM_D[5]
R1914
A 2 47 CI_DATA[6] PCM_D[6]
/PCM_CD CI_DATA[7] PCM_D[7]
CI_SLOT
GND 3 4 Y
CI_SLOT

PCM_D[0-7]
CI_DATA[0-7]

CI POWER ENABLE CONTROL

AR1908 33
CI_ADDR[8] PCM_A[8]
CI_ADDR[9] PCM_A[9]
+5V_Normal IC1901 CI_ADDR[10] PCM_A[10]
AP2151WG-7 +5V_CI_ON CI_SLOT
CI_ADDR[11] PCM_A[11]
L1900
BLM18PG121SN1D
IN OUT
5 1 CI_SLOT
CI_SLOT AR1909 33
GND CI_ADDR[12] PCM_A[12]
2
CI_SLOT R1916 CI_ADDR[13] PCM_A[13]
C1903
100K
R1902 1uF CI_ADDR[14] PCM_A[14]
100 EN FLG 25V CI_SLOT CI_SLOT
PCM_5V_CTL 4 3 REG /PCM_REG
CI_SLOT
R1901
10K
CI_SLOT AR1907 33
CI_OE /PCM_OE
CI_WE /PCM_WE
CI_IORD /PCM_IORD
CI_SLOT
CI_IOWR /PCM_IOWR

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS MT77 2013/08/07
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. PCMCI 19

Copyright ⓒ 2015 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes
 L15 GLOBAL TUNER

TUNER_T/C TUNER_CHINA TUNER_T2/C/S2

OPT
TU2602 TU2601 TU2600 OPT R2632
RF_SWITCH_CTL
0

TDJH-G301D TDJM-C401D TDJM-G301D C2630

0.1uF
16V
R2500
20K TU_I2C Multi option
OPT
+3.3V_LNA
Close to TUNER TU_ATSC
TU_I2C_FILTER
TU_ATSC R2608-*1
R2609-*1 MLG1005SR27JT
+3.3V +3.3V +3.3V C2609-*1
18pF
1.8K
1 1 1 TU_ATSC
C2607 C2608 TU_ATSC R2611-*1 TU_I2C_FILTER
0.1uF R2607-*1
NC_1 NC_1 NC_1 100pF
50V 16V C2612-*1
1.8K
MLG1005SR27JT
2 2 2 18pF

IF_AGC NC_2 AIF_AGC AGC_EU should be guarded by ground

R2606 +3.3V_TU
3 3 3 C2606 IF_AGC_MAIN
0.1uF AGC_KR/AJJA 0 TU_NON_ATSC TU_NON_ATSC
16V R2606-*1
SCL_RF SCL_RF SCL_RF 100 TU_I2C_NON_FILTER R2609
R2608 33 1K
R2611
1K
4 4 4 TU_SCL

SDA_RF SDA_RF SDA_RF TU_NON_ATSC

TU_I2C_NON_FILTER
TU_NON_ATSC TU_NON_ATSC
5 5 5 C2609 C2612
R2607 33
TU_SDA
C2615 C2616
TU_NON_ATSC TU_ATSC 20pF 20pF 20pF 20pF
IF[P] NC_3 AIF[P] R2604
10
R2604-*1 50V 50V 50V 50V
6 6 6 0 TU_NON_ATSC IF_P_MSTAR

IF[N] NC_4 AIF[N]

7 7 7 IF_N_MSTAR
TU_NON_ATSC TU_ATSC
R2605 R2605-*1 +3.3V_TU
SIF SIF SIF 10 R2615 0
8 8 8 0
TUNER_A_DEMOD

CVBS CVBS CVBS +3.3V_TU TUNER_BUFFER TUNER_BUFFER

9 9 9 R2619
220
R2620
220
TUNER_BUFFER 1% 1%
NC_5 NC_2 R2616
470 R2617
10 10 82
TU_SIF TU_CVBS
close to TUNER TUNER_BUFFER E
A1 B1 +3.3V_RF +3.3V_RF +3.3V_TU
C2617 TUNER_BUFFER
E
Q2601
A1 B1 11 11 C2600 C2601 Q2600 B MMBT3906(NXP)
0.1uF R2614 B MMBT3906(NXP) TUNER_BUFFER
100pF 0.1uF
T2_OR_CHINA 4.7K C
47 ERROR ERRORT2_OR_CHINA50V 16V AR2600 0 16V
TUNER_A_DEMOD C
TUNER_BUFFER

12 12 FE_TS_ERR
R2618
FE_TS_CLK 0
GND_1 GND_1 FE_TS_SYNC
TUNER_A_DEMOD
SHIELD 13 13 FE_TS_VAL CHINA
T2/C/S2 AR2600-*1 47
MCLK MCLK
14 14
TU_GND_B

SYNC SYNC
15 15
CHINA
AR2601-*1 47
VAILD VALID
16 16
T2/C/S2 FE_TS_DATA[0-7] +3.3V_LNA +3.3V_TU +3.3V_Normal
D0 D0 AR2601 0
17 17 FE_TS_DATA[0]
FE_TS_DATA[1]
CHINA
D1 D1 FE_TS_DATA[2] AR2602-*1 47 L2600
UBW2012-121F
L2603
UBW2012-121F
18 18 FE_TS_DATA[3]
C2619 C2620 C2622 C2624 C2628
C2623 C2626
D2 D2 22uF
10V
0.1uF
16V
22uF 0.1uF 47uF 22uF 0.1uF
19 19 10V 16V 16V
85C
10V 16V

D3 D3
20 20
T2/C/S2
D4 D4 AR2602 0
21 21 FE_TS_DATA[4]
+3.3V_TU +1.2V_DEMOD
TUNER_KR FE_TS_DATA[5]
IC2600
D5 D5 FE_TS_DATA[6]
AP7361-Y-13
TU2602-*2 22 22 FE_TS_DATA[7]
T2_OR_CHINA
R2621
TDJH-H301F D6 D6 3.3K EN
1 T2_OR_CHINA 5
OUT
23 23 C2618

T2_OR_CHINA
1uF GND R2631
D7 D7 10V 2
T2_OR_CHINA 1
+3.3V 24 24 T2_OR_CHINA R2623
1 ADJ/NC IN 12K
T2_OR_CHINA 3 4 1%
NC_1 RESET_DEMOD RESET_DEMOD R2600 R1
2 25 25 10
T2_OR_CHINA
DEMOD_RESET T2_OR_CHINA
T2_OR_CHINA C2627 C2631
DIF_AGC C2602 +3.3V_DEMOD 0.1uF 10uF
3 +3.3V_DEMOD +3.3V_DEMOD 0.1uF 16V 10V
SCL_RF
26 26 16V
T2_OR_CHINA
T2_OR_CHINA
4 C2610 C2613 T2_OR_CHINA
SCL_DEMOD SCL_DEMOD T2_OR_CHINA 100pF 0.1uF R2624
22K
SDA_RF 27 27 R2601 22
DEMOD_SCL
50V 16V 1%
5 C2603
20pF R2
DIF[P] +1.2V_DEMOD +1.2V_DEMOD 50V +1.2V_DEMOD
Vo=0.8*(1+R1/R2)
6 28 28 T2_OR_CHINA
C2611 C2614
DIF[N] 100pF 0.1uF
T2_OR_CHINA T2_OR_CHINA 50V 16VT2_OR_CHINA
7 NC_6 NC_3 R2602
GND seperation for CHINA tuner
SIF
29 29 0
LNB_TX
8

TU_GND_B
SDA_DEMOD SDA_DEMOD T2_OR_CHINA
R2603 22
CVBS 30 30 DEMOD_SDA
9 C2604
20pF
50V
LNB T2_OR_CHINA C2633
1000pF
31 C2605 LNB_OUT 630V
A1 B1 0.1uF
50V
A1 B1 A1 B1 GND T2_OR_CHINA
47
A1 B1 32
47 +3.3V_TU +3.3V_DEMOD
T2_OR_CHINA
SHIELD L2601
BLM18PG121SN1D
A1 B1
SHIELD A1 B1
T2_OR_CHINA T2_OR_CHINA T2_OR_CHINA
C2621 C2625 C2629
47 0.1uF 10uF 0.1uF
TU_GND_B

16V
10V 16V

SHIELD
ERROR & VALID PIN
T2_OR_CHINA
R2629
FE_TS_VAL 0
FE_TS_VAL_ERR
FE_TS_ERR
TU_GND_B

GPIO must be added.

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS MT77 2013/10/03
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. TUNER_EU_ERRC 26

Copyright ⓒ 2015 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes
 DVB-S2 LNB Part Allegro
(Option:LNB)

Input trace widths should be sized to conduct at least 3A

Ouput trace widths should be sized to conduct at least 2A

3A
+12V_LNB

2A LNB_SX34
D2704-*1
40V
LNB
Max 1.3A
L2701
SP-7850_15
D2704 15uH
LNB LNB_SMAB34
D2702 SMAB34
40V 3.5A

30V
LNB
C2710
10uF
LNB LNB LNB LNB
C2704 C2706 C2707 C2708 25V
0.01uF 10uF 10uF 10uF
50V 25V 25V 25V

close to Boost pin(#1)

A_GND A_GND
A_GND

close to VIN pin(#15)

LNB
LNB C2711

BOOST
[EP]

NC_4

NC_3

PGND
C2709 0.1uF
50V

LX
0.1uF
50V

20

19

18

17

16
LNB
D2701 NC_1 1 15 VIN
close to TUNER MBR230LSFT1G
LNB
THERMAL
GND
LNB_OUT 2 21 14
LNB
30V NC_2 VREG R2704
3 13 36K
IC2700
SMAB34

LNB LNB LNB TDI ISET 1/16W 1%

R2701 C2705 LNB_SMAB34 4 DT1803 12
LNB LNB LNB LNB C2703
2.2K 0.22uF 0.1uF D2703 LNB_DMB
C2700 C2701 C2702 D2700 1W 25V TDO 5 11 TCAP
50V 40V
18pF 18pF 33pF

10
50V 50V 50V LNB
6

9
LNB_SX34 C2713
D2703-*1 0.1uF
IRQ

SCL

SDA

ADD

40V TONECTRL LNB 50V

C2712
Close to Tuner 0.22uF
Surge protectioin 25V

A_GND A_GND

[EP]GND

BOOST

GNDLX
NC_3

NC_2
LNB LNB

LX
R2702 R2703
33 33

20

19

18

17

16
Caution!! need isolated GND VCP VIN
1 15
THERMAL
R2700 LNB 2 14 GND
0 21
NC_1 3 VREG
LNB_ALLEGRO13
DEMOD_SCL

DEMOD_SDA

LNB_TX

TDI 4 IC2700-*1 12 ISET

TDO A8303SESTR-T TCAP

5 11
A_GND

10
6

9
IRQ

SCL

SDA

ADD

TONECTRL
Max 1.3A

+12V_Normal +12V_LNB

LNB
L2700
BLM18PG121SN1D

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

Copyright ⓒ 2015 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes
 SCART / COMPONENT&COMPOSITE
SCART AMP
COMPONENT +19V
+3.3V_Normal

ZD2801
EAG60968213 5.6V
1%
ZD2800 R2824 EU
75
5.6V R2821 C2817
6A 10K
[GN/YL]E-LUG IC2801 0.1uF
AZ4580MTR-E1 50V
COMP_Y+/AV_CVBS_IN
5A [GN/YL]O-SPRING R2825
1K EU
AV_CVBS_DET R2861
2.2K OUT1 8 VCC
4A [GN/YL]CONTACT OPT 1
OPT DTV/MNT_L_OUT EU
VA2800 C2800 EU EU
COMP_Pb+ EU R2866 R2860
5B 5.6V 0.1uF C2821
[BL]O-SPRING ZD2802 16V OPT 33K IN1- 7 OUT2 2.2K EU
10uF R2865 2
5.6V R2800 16V DTV/MNT_R_OUT
470K EU C2822
7C [RD1]E-LUG-S 75 R2867 10uF
ZD2803 EU IN1+ IN2- 16V
1% 6 33K OPT
5.6V C2823 R2868 3
33pF 10K EU R2864
5C [RD1]O-SPRING 470K
50V R2869
EU VEE 5 IN2+ 10K
4 EU C2824
4C [RD1]CONTACT COMP_Pr+ 33pF
EU 50V
ZD2804 R2862
5D [WH]O-SPRING R2801 EU
5.6V 5.6K
75 R2863
ZD2805 SCART1_Lout
1% +3.3V_Normal 5.6K
4E [RD2]CONTACT 5.6V SCART1_Rout
330pF 220K
C2819 R2857
EU EU EU
5E 50V
[RD2]O-SPRING R2828 R2858 C2820
EU 220K 330pF
10K
R2829 50V
6E [RD2]E-LUG 1K
COMP_DET
PPJ245N2-01
JK2800 VA2803 CLOSE TO MSTAR
5.6V
OPT CLOSE TO MSTAR

R2822
10K
COMP_L_IN
C2825
VA2801 R2809 330pF R2826
12K
5.6V 470K 50V ATV_330P
C2802 OPT
1000pF
50V
R2823
10K
COMP_R_IN
R2820 C2826 R2827
VA2802
5.6V C2803 470K 330pF 12K
OPT 50V ATV_330P
1000pF
50V

+3.3V_Normal
FULL SCART
R2808
10K R2810
EU 1K
SCART1_DET
EU
D2808
5.6V
OPT

SC1_CVBS_IN
+3.3V_Normal
EU R2807
75 OPT
ZD2806 1% C2801
EU 47pF
5.6V 50V
22 ZD2807

R2874
AV_DET
5.6V

10K
21 EU
COM_GND EU

EU
L2800
20 CM2012FR22KT
SYNC_IN 220nH
DTV/MNT_VOUT
19 D2810 EU EU
R2830

SYNC_OUT D2811 C2815 C2816 SC1_FB

5.6V
EU
75

18 20V 68pF 68pF

EU Analog Switch
SYNC_GND2 EU 50V 50V EU
R2815 C
17 22
SYNC_GND1 B Q2000
16 MMBT3904(NXP)
RGB_IO
R2811 EU
15 SC1_R+ 75 E
R_OUT EU R2806 1%
14 D2812 75 EU
EU

RGB_GND 20V 1%
13
R_GND
12
D2B_OUT
11 SC1_G+
G_OUT
D2B_IN D2813 R2802
10 20V 75
EU

G_GND EU 1% EU
9 R2814
ID 15K
8 SC1_ID
B_OUT EU
7 SC1_B+ R2817 SAR2(LED Amber)
AUDIO_L_IN D2814 D2816
20V 3.9K
20V R2803
6 75 EU
EU
EU

B_GND
1%
5
AUDIO_GND EU
4
AUDIO_L_OUT R2812
10K
3 SC1_L_IN
AUDIO_R_IN OPT
2 R2804 EU R2818
AUDIO_R_OUT D2815 470K 12K
C2806
5.6V
EU

1 1000pF
EU
50V

SCART EU
JK2801 R2813
10K
PSC008-01 SC1_R_IN

D2817 OPT EU
5.6V R2805 C2807 R2819
470K 12K
EU 1000pF
EU

50V

DTV/MNT_L_OUT
D2818 EU
5.6V
C2804
OPT
1000pF
50V

DTV/MNT_R_OUT
D2819 EU
5.6V C2805
OPT 1000pF
50V

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS MT77 2013/10/03
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. COMPONENT/SCART 28

Copyright ⓒ 2015 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes
 This parts are Located
AUDIO AMP(TI) on AVSS area.
COIL_GETPLUS
L3451-*1
10.0uH
COIL_GETPLUS
L3453-*1
10.0uH
COIL_GETPLUS
L3450-*1
10.0uH
COIL_GETPLUS
L3452-*1
10.0uH

R3459
470
C3457 4700pF
50V
COIL_ABCO Close to Speaker

0.047uF
C3458

25V
L3451
R3453 10uH
0

C3459 2200pF
SPK_L+

C3462
0.033uF
50V
50V R3460
C3455 4700pF +19V 18

50V
C3454 R3458 C3470 OPT
330pF C3476 C3480
0.047uF 470 50V 0.1uF 2200pF
C3464 C3466

PVDD_AB_2
PVDD_AB_1
10uF 50V 50V
Separate DGND AND AVSS 0.1uF

PLL_FLTP
PLL_FLTM
+3.3V_Normal 25V 50V 25V

SSTIMER
VR_ANA
C3474

BST_A

OUT_A
0.47uF

AVSS
PBTL
NC_2

NC_1
OPT
+3.3V_ST C3471
50V
C3477
C3481 SPEAKER_L
330pF 2200pF
0.1uF 50V
[EP] 50V

12
11
10
9
8
7
6
5
4
3
2
1
50V
OPT AVDD 13 48 PGND_AB_2 R3461
R3450 18
C3451 R3457 2K A_SEL_FAULT PGND_AB_1

THERMAL
10K 14 47
0.1uF COIL_ABCO
MCLK 46 OUT_B

49
16V 15 SPK_L-
18K OSC_RES NC_6
R3454 16 45 50V L3453

TAS5733
IC3450
10K R3456 1% DVSSO 17 44 NC_5 0.033uF
C3468 10uH
VR_DIG 18 43 BST_B
R3455 PDN BST_C
19 42
C LRCLK NC_4
R3451 100 20 41 COIL_ABCO
10K C3450 50V
B Q3450 SCLK 40 NC_3 L3450
AMP_MUTE 1000pF C3453 21 0.033uF 10uH
MMBT3904(NXP) 50V SDIN OUT_C
0.1uF 22 39 C3469
16V SPK_R+
OPT E SDA 23 38 PGND_CD_2
R3452 SCL PGND_CD_1 OPT SPEAKER_R

R3462

1/16W
24 37
10K C3478 C3482
C3475

25
26
27
28
29
30
31
32
33
34
35
36
0.1uF 2200pF

18
AUD_LRCK
0.47uF 50V
AUD_SCK 50V 50V

RESET
STEST
DVDD
DVSS
GND
AGND
VREG
GVDD_OUT
BST_D
PVDD_CD_1
PVDD_CD_2
OUT_D
AUD_LRCH C3472 OPT
AMP_SDA 330pF C3483
+19V 50V 2200pF
AMP_SCL C3479
0.1uF 50V
C3473 50V
C3460

C34611uF 25V
0.1uF 330pF
AMP_RESET 16V 50V
+3.3V_Normal C3465 C3467
0.1uF 10uF

R3463

1/16W
50V 25V

18
COIL_ABCO
C3452 SPK_R-
0.1uF C3463 0.033uF
L3452
16V 50V
10uH
C3456
P3401
0.1uF
WAFER-ANGLE
16V

Headphone block SPK_L+

4

+3.3V_Normal SPK_L-
3

Head Phone
R3400 SPK_R+
2
47K Head Phone
R3412
1K SPK_R-
HP_DET 1
HP_LOUT
VA3401
20V Head Phone
OPT Head Phone C3402 C3406
OPT R3415 1000pF 10uF
1K 10V
Q3402 C 50V
E OPT OPT
MMBT3904(NXP)
B Q3404 Dip Detection Circuit
MMBT3904(NXP)
B
+19V
C E

6 M6 OPT
HP_ROUT
JP3400 AC KDS226
D3401
1 M1 JP3406 Head Phone OPT
R3418 OPT
Head Phone C3405
10uF 47K A C R3420
3 M3_DETECT OPT R3414 C3400
C 10V
JP3405 E 1000pF 470
Q3400 1K
B Q3403 50V OPT
4 M4 VA3400 MMBT3904(NXP) OPT C3428
MMBT3904(NXP) 47uF
JP3407 20V B E
VA3402 OPT 25V
C E OPT
5 M5_GND 20V +3.3V_ST MMBT3906(NXP)105C
B Q3407
KJA-PH-1-0177-2 Head Phone
JK3400 Head Phone C
Head Phone OPT OPT OPT
C3409 C3410 R3421
OPT OPT 12K
4.7uF 10uF
Q3405 50V R3419
MMBT3906(NXP) 25V
85C 220K
C

SB_MUTE
OPT 11.10.27 OPT
MUTE control Apply->OPT R3422 3K:
D3400
B

OPT MMBD6100 12K With SCART MUTE BLOCK

C OPT A2
R3416 R3417 SB_MUTE 12K:
3.3K B C
Without SCART MUTE BLOCK
10K A1
Q3406 HP_MUTE
E
MMBT3904(NXP)
OPT
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES
SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS MT77 2013/10/03
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR AMP_TAS5733/HP 34
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

Copyright ⓒ 2015 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes
 IC102
H27U1G8F2CTR-BC
NAND FLASH MEMORY +3.3V_Normal +3.3V_Normal
<CHIP Config> +5V_Normal
128M_SCALER
NC_1
1 48
NC_29 (PAD_PM_SPI_DI, PAD_PM_LED, PAD_PWM_PM)
NAND_FLASH_1G_HYNIX IC101
NC_2 EAN35669103
NC_28 LG-NonOS SB51_ExtSPI 3’b000 51 boot from SPI LGE2133(128M)
2 47
PCM_A[0-7] LG-OS HEMCU_ExtSPI 3’b001 MIPS boot from SPI
NC_3 NC_27
3 46

R132
CI_TS_CLK
22

R135

10K
10K
NC_4 NC_26 CI_TS_DATA[0-7]
4 45 R136 Y1 V10
AR101 WLED_ENABLE 100 GPIO78 TS0CLK/GPIO92
R107 NC_5 I/O7 PCM_A[7] W4 T14 CI_TS_DATA[0] CI_TS_SYNC
R109
1K 3.9K 5 44 C DSUB/SC1_OUT_CTRL GPIO79 TS0DATA[0]/GPIO82 CI_TS_DATA[1] CI_TS_VAL
R133 T13
NC_6 I/O6 PCM_A[6] +3.3V_ST Q100 B 4.7K EEPROM(IC104) TS0DATA[1]/GPIO83 CI_TS_DATA[2]
AR103 6 43 R184 22 K17 U13
22
OPT MMBT3904(NXP) I2C_SCL I2C_SCKM3/I2C_DDCR_CK/GPIO77 TS0DATA[2]/GPIO84 CI_TS_DATA[3] from CI SLOT
R/B I/O5 PCM_A[5] R183 22 J15 V15
7 42 R121 OPT I2C_SDA I2C_SDAM3/I2C_DDCR_DA/GPIO76 TS0DATA[3]/GPIO85 CI_TS_DATA[4]
E U8 U12
RE I/O4 PCM_A[4] AUD_MASTER_CLK_0 C116 R134
/F_RB HP_DET SDAM2/GPIO55 TS0DATA[4]/GPIO86 CI_TS_DATA[5]
8 41 56 2.2uF T7 V13

2.7K
OPT 1% SCART1_DET SCKM2/GPIO56 TS0DATA[5]/GPIO87

4.7K
/PF_OE 10V 4.7K CI_TS_DATA[6]
CE NC_25 U7 U14
9 40 C100 OPT

R119 4.7K
/PF_CE0 SCKM0/GPIO58 TS0DATA[6]/GPIO88 CI_TS_DATA[7]
V7 T11

OPT

OPT
NC_7 NC_24 100pF PANEL_CTL
10V SDAM0/GPIO59 TS0DATA[7]/GPIO89
10 39 50V DVB_S F6 T12

R116

R123
C102 R125 22 AMP_SCL I2S_IN_BCK/GPIO159 TS0SYNC/GPIO91 FE_TS_CLK
NC_8 NC_23 10uF DEMOD_SCL G6 V12
C101 11 38 R126 22 AMP_SDA I2S_IN_SD/GPIO160 TS0VALID/GPIO90 FE_TS_DATA[0-7]
DEMOD_SDA AA4 Y14
0.1uF VCC_1 VCC_2 DVB_S TU_SCL I2C_SCKM1/GPIO80 TS1CLK/GPIO103 FE_TS_SYNC
12 37 Y4 Y16 FE_TS_DATA[0]
TU_SDA I2C_SDAM1/GPIO81 TS1DATA[0]/GPIO93 FE_TS_DATA[1] FE_TS_VAL_ERR
16V VSS_1 VSS_2 C103 AA15
13 36 0.1uF
16V J6
TS1DATA[1]/GPIO94
Y13 FE_TS_DATA[2] Internal demod out
NC_9 NC_22 LED_RED AV_CVBS_DET ET_TXD[0]/GPIO62 TS1DATA[2]/GPIO95
14 35 K6 AA16 FE_TS_DATA[3]
PC_AUDIO_DET EXT_TX_CLK/GPIO64 TS1DATA[3]/GPIO96 FE_TS_DATA[4]
NC_10 NC_21 LED_AMBER W12
15 34 TS1DATA[4]/GPIO97 FE_TS_DATA[5]
G7 AA13
CLE NC_20 SPI_SDI COMP_DET I2S_IN_WS/GPIO158 TS1DATA[5]/GPIO98 FE_TS_DATA[6]
16 33 W14
AR102

4.7K

4.7K
TS1DATA[6]/GPIO99 FE_TS_DATA[7]
/PF_CE1 ALE I/O3 PCM_A[3] J4 W13
17 32

4.7K
DEMOD_RESET ET_COL/GPIO60 TS1DATA[7]/GPIO100

OPT
R120
PF_ALE J5 Y15
WE I/O2 PCM_A[2] MODEL_OPT_0 ET_TXD[1]/GPIO61 TS1SYNC/GPIO102
/PF_WE 18 31 W15

R117

R124
MODEL_OPT_1 TS1VALID/GPIO101
/PF_WP WP I/O1 PCM_A[1] If calculate current LED_RED level = 2.469V H19
19 30 LCK/GPIO194
If R123 is 2.7K, LED_RED level = 2.75V MODEL_OPT_2 G20 B3 R189 33
AR104 NC_11 I/O0 PCM_A[0] And LED_RED high threshold is 2.5V when boot up LDE/GPIO195 PM_SPI_SCZ1/GPIO_PM[6]/GPIO13 /SPI_CS
22 R106 20 29
Please use 2.7K for R123 G19 A3R188 33
R102 1K /MHL_OCP_DET LHSYNC/GPIO196 PM_SPI_SCK/GPIO1 SPI_SCK
NC_12 NC_19 22 G21 A4
3.3K 21 28 LVSYNC/GPIO197 PM_SPI_SCZ0/GPIO0 5V_DET_HDMI_1
C3
NC_13 NC_18 PM_SPI_SDI/GPIO2 SPI_SDI
22 27 J17 A2 R190 33
UART2_RX/GPIO69 PM_SPI_SDO/GPIO3 SPI_SDO
NC_14 NC_17 J16
23 26 UART2_TX/GPIO70 for SERIAL FLASH
E8 B1
NC_15 NC_16 MHL_OCP_EN UART3_TX/GPIO52 RP
24 25 D7 C2
AMP_RESET UART3_RX/GPIO53 TN
U6 C1
GPIO46[CTS] TP
V6 B2
Bluetooth Module MODEL_OPT_5
MODEL_OPT_6
K15
GPIO47[RTS]
UART1_TX/GPIO48
RN

L16 D2
UART1_RX/GPIO49 SPDIF_IN/GPIO161 HP_MUTE
D1 R197 100
DELETE 14/06/11 SPDIF_OUT/GPIO162 SPDIF_OUT
H5 SPDIF_OPTIC
USB_CTL ET_TX_EN/GPIO63
K5 D8
ET_RXD[0]/GPIO65 HWRESET SOC_RESET
NAND_FLASH_1G_TOSHIBA K4 E5
ET_MDC/GPIO66 IRIN/GPIO5 IR
H6 G4
NAND_FLASH_1G_MXIC EAN61508001 USB_OCD ET_MDIO/GPIO67 DDCA_CK/UART0_RX RGB_DDC_SCL
IC102-*1 IC102-*2 L5 G5
PCM_A[0-14] ET_RXD[1]/GPIO68 DDCA_DA/UART0_TX RGB_DDC_SDA
MX30LF1G08AA-TI TC58NVG0S3ETA0BBBH
PCM_A[0] U17 J18
PCM_A[1] PCMADR[0]/NF_AD[0]/GPIO130 PWM0/GPIO71 PWM0
R18 K18
NC_1 NC_29 NC_1 NC_29 PCM_A[2] PCMADR[1]/NF_AD[1]/GPIO129 PWM1/GPIO72 PWM1
1 48 1 48 V17 K16
PCM_A[3] PCMADR[2]/NF_AD[2]/GPIO127 PWM2/GPIO73 PWM2
NC_2 NC_28 NC_2 NC_28 R16 L18
2 47 2 47 PCM_A[4] PCMADR[3]/NF_AD[3]/GPIO126 PWM3/GPIO74 AMP_MUTE
U16 L17
NC_3 NC_27 NC_3 NC_27 PCM_A[5] PCMADR[4]/NF_AD[4]/GPIO104 PWM4/GPIO75 PCM_5V_CTL
3 46 3 46 T17
PCM_A[6] PCMADR[5]/NF_AD[5]/GPIO106
NC_4 NC_26 NC_4 NC_26 W18 T8
PCMADR[6]/NF_AD[6]/GPIO107 NF_ALE/GPIO146 PF_ALE +3.3V_Normal
4 45 4 45 PCM_A[7] U20 T9
NC_5 I/O7 NC_5 I/O8 PCM_A[8] PCMADR[7]/NF_AD[7]/GPIO108 NF_CEZ/GPIO142 /PF_CE0
5 44 5 44 Y19 U9
PCM_A[9] PCMADR[8]/GPIO113 NF_CLE/GPIO141 /PF_CE1
NC_6 I/O6 NC_6 I/O7 AA19 U11
6 43 6 43 PCM_A[10] PCMADR[9]/GPIO115 NF_RBZ/GPIO147 /F_RB
AA20 V9
R/B I/O5 RY/BY I/O6 PCM_A[11] PCMADR[10]/GPIO119 NF_REZ/GPIO144 /PF_OE C119
7 42 7 42 W21 U10 0.1uF
PCM_A[12] PCMADR[11]/GPIO117 NF_WEZ/GPIO145 /PF_WE R193 16V
RE I/O4 RE I/O5 V20 T10 10K
8 41 8 41 PCM_A[13] PCMADR[12]/GPIO109 NF_WPZ/GPIO199 /PF_WP
Y17
CE NC_25 CE NC_25 PCM_A[14] PCMADR[13]/GPIO112
9 40 9 40 /PCM_CD V18 W2
/PCM_CE PCMADR[14]/GPIO111 IF_AGC IF_AGC_MAIN
NC_7 NC_24 NC_7 NC_24 V19 W1
10 39 10 39 PCM_D[0-7] PCMCD_N/GPIO135 SIFM
W19 W3 C120
NC_8 NC_23 NC_8 NC_23 PCMCE_N/GPIO120 SIFP 0.047uF
11 38 11 38 PCM_D[0] U18 V2
PCMDATA[0]/GPIO131 IM 25V
VCC_1 VCC_2 VCC_1 VCC_2 PCM_D[1] V16 V1
12 37 12 37 PCMDATA[1]/GPIO132 IP
PCM_D[2] W17
VSS_1 VSS_2 VSS_1 VSS_2 PCMDATA[2]/GPIO133
13 36 13 36 PCM_D[3] Y20 AA2
PCMDATA[3]/GPIO125 XIN
NC_9 NC_22 NC_9 NC_22 PCM_D[4] R15 Y2 R127 47
14 35 14 35 PCMDATA[4]/GPIO124 XOUT C110 0.1uF
PCM_D[5] AA18 16V R128 47
NC_10 NC_21 NC_10 NC_21 IC101-*1 PCMDATA[5]/GPIO123 C112 0.1uF OPT
15 34 15 34 LGE2134(256M) PCM_D[6] T15 16V C115
PCMDATA[6]/GPIO122 1000pF
CLE NC_20 CLE NC_20 PCM_D[7] Y21 ANALOG SIF 50V
16 33 16 33 BLUETOOTH DELETE 14/06/11 256M_SCALER PCMDATA[7]/GPIO121
Y1
GPIO78 TS0CLK/GPIO92
V10 W20 Close to MSTAR TU_SIF
ALE I/O3 ALE I/O4
W4
GPIO79 TS0DATA[0]/GPIO82
T14
/PCM_IORD PCMIORD_N/GPIO116
17 32 17 32 TS0DATA[1]/GPIO83
T13 V21
K17
I2C_SCKM3/I2C_DDCR_CK/GPIO77 TS0DATA[2]/GPIO84
U13
/PCM_IOWR PCMIOWR_N/GPIO114
WE I/O2 WE I/O3
J15
I2C_SDAM3/I2C_DDCR_DA/GPIO76 TS0DATA[3]/GPIO85
V15 Y18
18 31 18 31
U8
T7
SDAM2/GPIO55 TS0DATA[4]/GPIO86
U12
V13
/PCM_IRQA
T16
PCMIRQA_N/GPIO110 Close to MSTAR
SCKM2/GPIO56 TS0DATA[5]/GPIO87
WP I/O1 WP I/O2
U7
SCKM0/GPIO58 TS0DATA[6]/GPIO88
U14
/PCM_OE PCMOE_N/GPIO118 C117
19 30 19 30
V7
SDAM0/GPIO59 TS0DATA[7]/GPIO89
T11 R17 0.1uF IF_N_MSTAR
F6
I2S_IN_BCK/GPIO159 TS0SYNC/GPIO91
T12
/PCM_REG PCMREG_N/GPIO128 OPT
G6 V12 T18 16V
NC_11 I/O0 NC_11 I/O1 I2S_IN_SD/GPIO160 TS0VALID/GPIO90 C121
20 29 20 29
AA4
Y4
I2C_SCKM1/GPIO80 TS1CLK/GPIO103
Y14
Y16
PCM_RST
W16
PCM_RESET/GPIO134 100pF DTV_IF
I2C_SDAM1/GPIO81 TS1DATA[0]/GPIO93
AA15
/PCM_WAIT 50V
NC_12 NC_19 NC_12 NC_19 TS1DATA[1]/GPIO94 PCMWAIT_N/GPIO105
21 28 21 28
J6
ET_TXD[0]/GPIO62 TS1DATA[2]/GPIO95
Y13 U15 C118
K6
EXT_TX_CLK/GPIO64 TS1DATA[3]/GPIO96
AA16
W12
/PCM_WE PCMWE_N/GPIO198 0.1uF IF_P_MSTAR
NC_13 NC_18 NC_13 NC_18 G7
TS1DATA[4]/GPIO97
AA13 16V
22 27 22 27 I2S_IN_WS/GPIO158 TS1DATA[5]/GPIO98
W14 OPT OPT
J4
TS1DATA[6]/GPIO99
W13 C108 C109
NC_14 NC_17 NC_14 NC_17 J5
ET_COL/GPIO60 TS1DATA[7]/GPIO100
Y15 33pF 33pF
23 26 23 26 ET_TXD[1]/GPIO61 TS1SYNC/GPIO102
W15 50V 50V
TS1VALID/GPIO101
H19
NC_15 NC_16 NC_15 NC_16 G20
LCK/GPIO194
B3
24 25 24 25 G19
LDE/GPIO195 PM_SPI_SCZ1/GPIO_PM[6]/GPIO13
A3
G21
LHSYNC/GPIO196 PM_SPI_SCK/GPIO1
A4 C113 24pF
LVSYNC/GPIO197 PM_SPI_SCZ0/GPIO0
C3
PM_SPI_SDI/GPIO2
J17 A2

R187
J16
UART2_RX/GPIO69 PM_SPI_SDO/GPIO3 X101 50V

1M
1%
UART2_TX/GPIO70
E8
UART3_TX/GPIO52 RP
B1 24MHz C114 24pF
D7 C2
UART3_RX/GPIO53 TN
U6 C1
GPIO46[CTS] TP
V6 B2
K15
GPIO47[RTS] RN 50V
UART1_TX/GPIO48
L16 D2
UART1_RX/GPIO49 SPDIF_IN/GPIO161
D1
SPDIF_OUT/GPIO162
H5
ET_TX_EN/GPIO63
K5 D8
DIMMING I2C K4
ET_RXD[0]/GPIO65
ET_MDC/GPIO66
HWRESET
IRIN/GPIO5
E5
+3.3V_Normal BOOT KEY OPTION H6
ET_MDIO/GPIO67 DDCA_CK/UART0_RX
G4
L5 G5
ET_RXD[1]/GPIO68 DDCA_DA/UART0_TX

U17 J18
PCMADR[0]/NF_AD[0]/GPIO130 PWM0/GPIO71
R18 K18
+3.3V_ST V17
PCMADR[1]/NF_AD[1]/GPIO129 PWM1/GPIO72
K16
PCMADR[2]/NF_AD[2]/GPIO127 PWM2/GPIO73
OPT R16
U16
PCMADR[3]/NF_AD[3]/GPIO126 PWM3/GPIO74
L18
L17
R113 10K HIGH : 1600x900 T17
PCMADR[4]/NF_AD[4]/GPIO104 PWM4/GPIO75
PWM0 W18
PCMADR[5]/NF_AD[5]/GPIO106
T8

R101 R103 R140 R141 R144 R145 OPT LOW : Normal U20
Y19
PCMADR[6]/NF_AD[6]/GPIO107
PCMADR[7]/NF_AD[7]/GPIO108
NF_ALE/GPIO146
NF_CEZ/GPIO142
T9
U9
R156 10K 4.7K 4.7K 1K 1K 2.2K 2.2K R114 AA19
PCMADR[8]/GPIO113 NF_CLE/GPIO141
U11
BLU_CURRENT_CTL PWM1 10K PCMADR[9]/GPIO115 NF_RBZ/GPIO147
OPT
AA20
W21
PCMADR[10]/GPIO119 NF_REZ/GPIO144
V9
U10
128M_SCALER
R104 100 V20
Y17
PCMADR[11]/GPIO117
PCMADR[12]/GPIO109
NF_WEZ/GPIO145
NF_WPZ/GPIO199
T10 IC101
WLED_DIM_ADJ
R157 100 AMP_SDA
BOOT_KEY_OPTION V18
PCMADR[13]/GPIO112
PCMADR[14]/GPIO111 IF_AGC
W2 LGE2133(128M)
PWM2 V19
W19
PCMCD_N/GPIO135 SIFM
W1
W3 C106 C107
AMP_SCL U18
PCMCE_N/GPIO120 SIFP
V2 0.1uF 0.1uF
PCMDATA[0]/GPIO131 IM
V16 V1
R100 C111 W17
PCMDATA[1]/GPIO132 IP 16V 16V
3.9K I2C_SDA Y20
PCMDATA[2]/GPIO133
AA2
2.2uF R15
PCMDATA[3]/GPIO125 XIN
Y2 U19 D5
10V I2C_SCL AA18
PCMDATA[4]/GPIO124 XOUT MODEL_OPT_4 OPT LVA4P/TTL_B[0]/HCONV/GPIO170 SAR0/GPIO35 KEY1
R115 T15
PCMDATA[5]/GPIO123 T20 F8
10K Y21
PCMDATA[6]/GPIO122
RF_SWITCH_CTL LVA4M/TTL_B[1]/E_O/GPIO171 SAR1/GPIO36 KEY2
KEY_SDA W20
PCMDATA[7]/GPIO121
33 R142 T21 E7
V21
PCMIORD_N/GPIO116 RXA3+ LVA3P/TTL_B[2]/FB/GPIO172 SAR2/GPIO37 SC1_ID
KEY_SCL Y18
PCMIOWR_N/GPIO114 T19 E6 LED_AMBER -> SC1_ID
T16
PCMIRQA_N/GPIO110 RXA3- LVA3M/TTL_B[3]/OPT_P/GPIO173 SAR3/GPIO38 KEY_SCL
R17
PCMOE_N/GPIO118 R21 D6
T18
PCMREG_N/GPIO128 RXACK+ LVACKP/TTL_B[4]/MCLK/GPIO174 SAR4/GPIO39 KEY_SDA
W16
PCM_RESET/GPIO134 R20
U15
PCMWAIT_N/GPIO105 RXACK- LVACKM/TTL_B[5]/GCLK/GPIO175
PCMWE_N/GPIO198 R19 W10
RXA2+ LVA2P/TTL_B[6]/GST/GPIO176 GPIO_PM[13]/GPIO20 MHL_CD_SENSE
P20 Y10
EEPROM RXA2- LVA2M/TTL_B[7]/POL/GPIO177 GPIO_PM[14]/GPIO21 /VBUS_EN
+3.3V_Normal P3
PM_LED/GPIO4 LED_AMBER
Flash Memory RXA1+
P19 Y3
LVA1P/TTL_G[0]/EPI0+/GPIO178 GPIO_PM[0]/GPIO7 DSUB_DET PM_LED -> LED_AMBER
N20 Y5
RXA1- LVA1M/TTL_G[1]/EPI0-/GPIO179 PM_SPI_SCZ2/GPIO_PM[10]/GPIO17 BOOT_KEY_OPTION
SPI_FLASH_MACRONIX SPI_FLASH_WINBOND N21 W11
RXA0+ LVA0P/TTL_G[2]/EPI1+/GPIO180 GPIO_PM[15]/GPIO22 5V_DET_HDMI_2
NVRAM_ROHM IC100 +3.3V_ST IC100-*1 N19 D3
C105 NVRAM_ATMEL RXA0- LVA0M/TTL_G[3]/EPI1-/GPIO181 GPIO_PM[4]/GPIO11 POWER_ON/OFF1 IC101-*1
IC104 MX25L8035EM2I-10G W25Q80DVSSIG M21 AA3 LGE2134(256M)
0.1uF IC104-*1 LVB4P/TTL_G[4]/EPI2+/GPIO182 GPIO_PM[7]/GPIO14 MULTI_ON
BR24G256FJ-3 M20 W5
16V AT24C256C-SSHL-T
C104 LVB4M/TTL_G[5]/EPI2-/GPIO183 GPIO_PM[8]/GPIO15 /FLASH_WP 256M_SCALER
+3.3V_ST M19 D4 U19
LVA4P/TTL_B[0]/HCONV/GPIO170 SAR0/GPIO35
D5

CS# VCC 0.1uF CS VCC RXB3+ LVB3P/TTL_G[6]/EPI3+/GPIO184 PWM_PM/GPIO200 LED_RED T20

LVA4M/TTL_B[1]/E_O/GPIO171 SAR1/GPIO36
F8
A0 VCC L20 L15 T21 E7
1 8 A0 VCC /SPI_CS 1 8 1 8 RXB3-
LVA3P/TTL_B[2]/FB/GPIO172 SAR2/GPIO37
1 8 LVB3M/TTL_G[7]/EPI3-/GPIO185 PM_UART_TX/GPIO_PM[1]/GPIO8 PM_TXD T19
LVA3M/TTL_B[3]/OPT_P/GPIO173 SAR3/GPIO38
E6

16V Y11 R21

LVACKP/TTL_B[4]/MCLK/GPIO174 SAR4/GPIO39
D6

A1 WP R118 PM_UART_RX/GPIO_PM[5]/GPIO12 PM_RXD R20

LVACKM/TTL_B[5]/GCLK/GPIO175
2 7 SO/SIO1 NC/SIO3 DO[IO1] HOLD[IO3] L19 R19
LVA2P/TTL_B[6]/GST/GPIO176 GPIO_PM[13]/GPIO20
W10
A1 WP RXBCK+ LVBCKP/TTL_R[0]/EPI4+/GPIO186 P20 Y10
2 7 10K SPI_SDO 2 7 2 7 K20
LVA2M/TTL_B[7]/POL/GPIO177 GPIO_PM[14]/GPIO21
A0’h RXBCK- LVBCKM/TTL_R[1]/EPI4-/GPIO187 P19
LVA1P/TTL_G[0]/EPI0+/GPIO178
PM_LED/GPIO4
GPIO_PM[0]/GPIO7
P3
Y3
A2 SCL K21 N20 Y5
3 6 R111 22 I2C_SCL A2 SCL LVA1M/TTL_G[1]/EPI0-/GPIO179 PM_SPI_SCZ2/GPIO_PM[10]/GPIO17
3 6 WP#/SIO2 SCLK WP[IO2] CLK RXB2+ LVB2P/TTL_R[2]/EPI5+/GPIO188 N21
LVA0P/TTL_G[2]/EPI1+/GPIO180 GPIO_PM[15]/GPIO22
W11

3 6 3 6 K19 N19
LVA0M/TTL_G[3]/EPI1-/GPIO181 GPIO_PM[4]/GPIO11
D3
SPI_SCK RXB2- LVB2M/TTL_R[3]/EPI5-/GPIO189 M21
LVB4P/TTL_G[4]/EPI2+/GPIO182 GPIO_PM[7]/GPIO14
AA3
GND SDA J21 M20 W5
4 5 R112 22 GND SDA /FLASH_WP LVB4M/TTL_G[5]/EPI2-/GPIO183 GPIO_PM[8]/GPIO15
I2C_SDA 4 5 R122 RXB1+ LVB1P/TTL_R[4]/EPI6+/GPIO190 M19
LVB3P/TTL_G[6]/EPI3+/GPIO184 PWM_PM/GPIO200
D4

GND SI/SIO0 GND DI[IO0] J20 L20

LVB3M/TTL_G[7]/EPI3-/GPIO185 PM_UART_TX/GPIO_PM[1]/GPIO8
L15
33 RXB1- LVB1M/TTL_R[5]/EPI6-/GPIO191 Y11
4 5 SPI_SDI 4 5 J19 L19
PM_UART_RX/GPIO_PM[5]/GPIO12
LVBCKP/TTL_R[0]/EPI4+/GPIO186
RXB0+ LVB0P/TTL_R[6]/EPI7+/GPIO192 K20
LVBCKM/TTL_R[1]/EPI4-/GPIO187
H20 K21
LVB2P/TTL_R[2]/EPI5+/GPIO188
RXB0- LVB0M/TTL_R[7]/EPI7-/GPIO193 K19
LVB2M/TTL_R[3]/EPI5-/GPIO189
J21
LVB1P/TTL_R[4]/EPI6+/GPIO190
J20
LVB1M/TTL_R[5]/EPI6-/GPIO191
J19
LVB0P/TTL_R[6]/EPI7+/GPIO192
H20
LVB0M/TTL_R[7]/EPI7-/GPIO193

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS MT77 2013/09/16
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. MAIN1_NON_EU 51

Copyright ⓒ 2015 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes
 MODEL OPTION +1.15V_VDDC
+3.3V_Normal PIN NAME PIN NO. LOW HIGH VDDC 1.15V +1.15V_VDDC

MODEL OPTION VDDC : 2026mA

MODEL_OPT_0 J5 FHD HD
DVB_T2/C/S2
1K

1K

1K

1K

1K

1K

1K
1K

MODEL_OPT_1
TW/CN_NOT

H19 S/W_NON_AJ S/W_AJ

EXT_256M

EXT_128M

S/W_AJ
EU_NOT

C203

ZD201
C202
OPT

OPT

2.5V
C228 C275 C277 C280 C283
MODEL_OPT_2 G20 DVB_T/C DVB_T2/C/S2 & CHINA 10uF 10uF 1uF 1uF 0.1uF
10uF 0.1uF
10V 16V
10V 10V 10V 10V 16V
R291

R222

R221

R206

R208

R211

R226
R290

AUD_LRCH G19 NON_M120 M120

MODEL_OPT_0
MODEL_OPT_4 U6
MODEL_OPT_1
R203 0 MODEL_OPT_5 K5 S/W_TW/CN S/W_EU/AJ
RF_SWITCH_CTL MODEL_OPT_2
OPT AUD_LRCH MODEL_OPT_6 K4
MODEL_OPT_4
MODEL_OPT_5 AUD_LRCK L5 NON_DUALSTREAM DUALSTREAM
MODEL_OPT_6
AUD_LRCK * Dual Stream is only Korea 3D spec
DVB_T2/C/S2_NOT

128M_SCALER
Normal Power 3.3V
1K
S/W_NON_AJ
EXT_NON_256M

IC101
EXT_NON_128M
1K
1K

1K

1K

1K

1K

1K

Memory OPTION +3.3V_Normal LGE2133(128M)

TW/CN
EU

Memory Auto
R212

MODEL_OPT_4 MODEL_OPT_6
R294
R293

R224

R223

R207

R209

R227

INT+EXT Det R4 U3
AVDD_AU33 AVDD_AU33 AUVRM AUVRM
L11 A6
AVDD_DDR0_CLK GND_1
128M Only 0 0 0 L13 A13

10V

10V

0.1uF 16V

0.1uF 16V

0.1uF 16V
ZD202
AVDD_DDR1_CLK GND_2

C235

C245
M11 A15

C209
5V
C255 C259 AVDD_DDR0_CMD GND_3
0.1uF 0.1uF K13 A18

C284
10uF

C204
10uF
OPT
256M Only 1 0 0 16V 16V AVDD_DDR1_CMD GND_4
+1.5V_DDR C5 B12
AVDD_DDR0_D_1 GND_5
K12 B14
128M+128M 0 1 0 L12
AVDD_DDR0_D_2 GND_6
B16
AVDD_DDR0_D_3 GND_7
256M_SCALER C6 B17
AVDD_DDR1_D_1 GND_8
128M+256M 0 0 1 K14 B19
IC101-*1 AVDD_DDR1_D_2 GND_9
L14 B20
LGE2134(256M) 1 1 AVDD_DDR1_D_3 GND_10
256M+128M 0 B5 C9
AVDD_DRAM_1 GND_11
B6 C10
AVDD_DRAM_2 GND_12
R8 C21
M4 T6 256M+256M 1 0 1 AVDD_NODIE AVDD_DVI_USB_MPLL_1 GND_13
ARC0 R9 D9
CVBSOUT1 AVDD_DVI_USB_MPLL_2 GND_14
W7 V5 L7 E20
RXC0N CVBS0 +3.3V_Normal AVDD_MOD_1 GND_15
Y8 U5 L8 F9
RXC0P CVBS1 AVDD_MOD_2 GND_16
W8 T5 P8 F11
RXC1N CVBS2 AVDD_NODIE AVDD_NODIE GND_17
Y9
AA9
RXC1P VCOM
V4
M1A(128M) ’ EAN62929401(LGE2133) +3.3V_Normal
K9
AVDD_PLL GND_18
F13
R5 F15
W9
RXC2N
RXC2P I2S_OUT_BCK/GPIO165
E4 M1A(256M) ’ EAN62929501(LGE2134) AVDD_DMPLL
+1.15V_VDDC P11
AVDD3P3_DMPLL GND_19
F17
AA7 F4 AVDDL_MOD GND_20
RXCCKN C7 F19
I2S_OUT_MCK/GPIO163
Y7
RXCCKP I2S_OUT_SD/GPIO166
F7 MT75 KR :128M+128M +1.15V_VDDC
M13
DVDD_DDR_1
DVDD_DDR_2
GND_21
GND_22
F21
N2 F5 C260 R6 G8
CEC/GPIO6 I2S_OUT_WS/GPIO164 DVDD_NODIE GND_23
E3
E2
DDCDA_CK/GPIO27
C4
MT75 AJ/CN/ETC :256M+128M 1uF
10V
A7
DVDD_RX_1_1 GND_24
G9

W6
DDCDA_DA/GPIO28 USB0_DM
Y12
Normal 2.5V M12
DVDD_RX_1_2 GND_25
G10

AA6
DDCDC_CK/GPIO31 USB1_DM
B4 MT75 EU:128M+128M +1.15V_VDDC
B7
M14
DVDD_RX_2_1 GND_26
G11
G12
DDCDC_DA/GPIO32 USB0_DP DVDD_RX_2_2 GND_27
L4
Y6
HOTPLUGA/GPIO23 USB1_DP
AA12
MT75 BR:128M+256M ฀ 2.5V inbeded
M1A +1.15V_VDDC
N11
VDDC_1 GND_28
G13

HOTPLUGC/GPIO25 N12 G14

F1 J2 VDDC_2 GND_29
RXA0N N13 G15
BIN0M
G3
RXA0P BIN0P
J3 2014.6.09 N14
VDDC_3
VDDC_4
GND_30
GND_31
G16
G1 K3 N15 G17
RXA1N GIN0M VDDC_5 GND_32
G2 J1 P12 G18
RXA1P GIN0P VDDC_6 GND_33
H3
H2
RXA2N RIN0M
K2
K1
WIFI Module P13
VDDC_7 GND_34
H7

RXA2P P14 H8
RIN0P VDDC_8 GND_35
F3 M6 L9 H9
RXACKN HSYNC0 7 +3.3V_Normal VDDP GND_36
F2 L6 H10
RXACKP VSYNC0 GND_37
WIFI AA10 H11
6 AVDD5V_MHL AVDD5V_MHL GND_38
U4 L2 H12
EAR_OUTL BIN1M R202
T4
EAR_OUTR BIN1P
L3 0 DDR3 1.5V GND_39
GND_40
H13
P2 M1 5 IC101-*1
H14
AUL1 GIN1M LGE2134(256M)
GND_41
R2 M2 H15
AUL2 GIN1P WIFI GND_42
T1 N1 256M_SCALER
U3 R4 H16
AUL3 RIN1M L203 4 A6
AUVRM AVDD_AU33
L11
GND_43
R3 N3 A13
GND_1 AVDD_DDR0_CLK
L13 H17
AUR1 RIN1P ACM2012-900H-2P JP200 A15
GND_2 AVDD_DDR1_CLK
M11
GND_44
R1 M3 1 4 A18
GND_3 AVDD_DDR0_CMD
K13 H18
AUR2 SOGIN1 WIFI_USB_DP +1.5V_DDR B12
GND_4 AVDD_DDR1_CMD
C5
GND_45
T3 3 B14
GND_5 AVDD_DDR0_D_1
K12 J7
AUR3 B16
GND_6 AVDD_DDR0_D_2
L12
GND_46
U2 JP201 B17
GND_7 AVDD_DDR0_D_3
C6 J8
AUOUTL0 2 3 AVDD_DDR0:55mA B19
GND_8 AVDD_DDR1_D_1
K14
GND_47
V3 WIFI_USB_DM B20
GND_9 AVDD_DDR1_D_2
L14 J9
AUOUTR0 2 C9
GND_10 AVDD_DDR1_D_3
B5
GND_48
T2 D201 D202 C10
GND_11 AVDD_DRAM_1
B6 J10
AUVAG JP202 C21
GND_12 AVDD_DRAM_2
R8
GND_49
5.6V 5.6V D9
GND_13
GND_14
AVDD_DVI_USB_MPLL_1
AVDD_DVI_USB_MPLL_2
R9 J11

0.1uF 16V
ZD203
E20 L7
GND_50

0.1uF 16V

0.1uF 16V

1uF 10V
2.5V
GND_15 AVDD_MOD_1
1

C266
+3.5V_WIFI READY READY F9 L8 J12

10uF 10V

C207

C254
GND_16 AVDD_MOD_2

C248
F11 P8
GND_17 AVDD_NODIE GND_51
F13
GND_18 AVDD_PLL
K9 J13
F15 R5
GND_52

C278
WIFI F17
GND_19 AVDD3P3_DMPLL
P11 J14
GND_20 AVDDL_MOD
F19 C7
L215 GND_21 DVDD_DDR_1 GND_53
UBW2012-121F 12507WR-06L F21
GND_22 DVDD_DDR_2
M13 K8
G8 R6
GND_23 DVDD_NODIE GND_54
P200 G9
GND_24 DVDD_RX_1_1
A7 K10
G10 M12
GND_25 DVDD_RX_1_2 GND_55
C289 C290 WIFI
G11
GND_26 DVDD_RX_2_1
B7 K11
G12 M14
C287 C288 AVDD_DDR1:55mA GND_27 DVDD_RX_2_2 GND_56
10uF 10uF G13
GND_28 VDDC_1
N11 L10
0.1uF 0.1uF G14
GND_29 VDDC_2
N12
GND_57
16V 16V 10V 10V G15
GND_30 VDDC_3
N13 M5
G16 N14
WIFI GND_31 VDDC_4 GND_58
WIFI WIFI OPT G17
GND_32 VDDC_5
N15 M7
G18 P12
GND_33 VDDC_6 GND_59
H7
GND_34 VDDC_7
P13 M8
H8 P14
GND_35 VDDC_8 GND_60
For EMI
H9
GND_36 VDDP
L9 M9
H10
GND_37 GND_61
H11
GND_38 AVDD5V_MHL
AA10 M10
H12
GND_39 GND_62
H13
GND_40 N4
H14
GND_41 GND_63
H15
GND_42 N5
128M_SCALER H16
GND_43 GND_64
H17
GND_44 N6
IC101 H18
J7
GND_45
GND_46
GND_65
N7
LGE2133(128M)
HDMI

J8
GND_47 GND_66
J9
GND_48 N8
J10
HDMI1_ARC GND_49 GND_67
J11
GND_50 N9
C212 J12
GND_51 GND_68
1uF HDMI1_ARC J13
GND_52 N10
10V R231
J14
GND_53 GND_69
M4 T6 K8
GND_54 P4
HDMI_ARC ARC0 CVBSOUT1 DTV/MNT_VOUT K10
GND_55 GND_70
0 W7 V5 C243 0.047uF 33 R201 K11
GND_56 P5
D0-_HDMI2 RXC0N CVBS0 25V TU_CVBS L10
GND_57 GND_71
10 R214 Y8 U5 C237 0.047uF 33 R245 M5
GND_58 P6
D0+_HDMI2 RXC0P CVBS1 25V SC1_CVBS_IN M7
GND_59 GND_72
10 R215 W8 T5 C238 0.047uF 33 R246 M8
GND_60 P7
D1-_HDMI2 RXC1N CVBS2 COMP_Y+/AV_CVBS_IN +3.3V_Normal
M9
GND_61 GND_73
Y9 V4 25V R247 M10 P9
C239 OPT GND_62
D1+_HDMI2 RXC1P VCOM 0.047uF C244
N4
GND_63 GND_74
AA9 68 1000pF
N5
GND_64 P10
D2-_HDMI2 RXC2N 25V N6
GND_75
W9 E4 50V N7
GND_65
P15
GND_66
R248

R250

RXC2P I2S_OUT_BCK/GPIO165 N8
GND_76
10K

D2+_HDMI2 I2S_I/F
10K

GND_67
AA7 F4
OPT

P16
OPT

N9
GND_68
CK-_HDMI2 RXCCKN I2S_OUT_MCK/GPIO163 N10
GND_69 GND_77
Y7 F7 P4
GND_70 P17
CK+_HDMI2 RXCCKP I2S_OUT_SD/GPIO166 AUD_SCK P5
GND_71 GND_78
N2 F5 P6
GND_72 P18
CEC_REMOTE_S7 CEC/GPIO6 I2S_OUT_WS/GPIO164 AUD_MASTER_CLK_0 P7
GND_73 GND_79
E3 P9
GND_74 R10
DDC_SCL_1 DDCDA_CK/GPIO27 AUD_LRCH P10
GND_75 GND_80
E2 C4 P15
GND_76 R11
DDC_SDA_1 DDCDA_DA/GPIO28 USB0_DM AUD_LRCK P16
GND_77 GND_81
W6 Y12 P17 R12
DDC_SCL_2 DDCDC_CK/GPIO31 USB1_DM 0 R295 WIFI P18
GND_78
GND_82
R251

GND_79
R249

AA6 B4 WIFI_USB_DM R10 R13

10K

10K

GND_80
OPT

OPT

DDC_SDA_2 DDCDC_DA/GPIO32 USB0_DP USB_DM

R11
GND_81 GND_83
L4 AA12 0 R296 WIFI R12
GND_82 R14
HPD1 HOTPLUGA/GPIO23 USB1_DP WIFI_USB_DP
R13
GND_83 GND_84
Y6 R14
GND_84 K7
HPD2 HOTPLUGC/GPIO25 USB_DP K7
GND_EFUSE GND_EFUSE
F1 J2 C221 25V R232
D0-_HDMI1 RXA0N BIN0M 0.047uF 100 SIDE USB OPT OPT
G3 J3 C222 25V R233
D0+_HDMI1 RXA0P BIN0P 0.047uF 33 DSUB/SC1_B+ C285 C286
G1 K3 C223 25V R234 5pF 5pF
D1-_HDMI1 RXA1N GIN0M 0.047uF 100
G2 J1 C224 25V R235 50V 50V
D1+_HDMI1 RXA1P GIN0P 0.047uF 33 DSUB/SC1_G+
H3 K2 C225 25V R236
D2-_HDMI1 RXA2N RIN0M 0.047uF 100
H2 K1 C226 25V R237
D2+_HDMI1 RXA2P RIN0P 0.047uF 33 DSUB/SC1_R+
F3 M6 R210 SOC_RESET
CK-_HDMI1 RXACKN HSYNC0 DSUB/SC1_HSYNC
CK+_HDMI1
F2
RXACKP VSYNC0
L6 33
R213
33 DSUB/SC1_VSYNC +3.3V_ST
STby 3.3V
H/P OUT +3.3V_ST AVDD_NODIE
Head Phone 5.6uH L212 U4 L2 C227 25V R238 L201
HP_LOUT EAR_OUTL BIN1M 0.047uF 68
Head Phone 5.6uH L213 T4 L3 C229 25V R239 BLM18PG121SN1D
HP_ROUT EAR_OUTR BIN1P 0.047uF 33 COMP_Pb+
C214 2.2uF P2 M1 C230 25V R240
SC1_L_IN 10V AUL1 GIN1M 0.047uF 68 C200 111026Switch AVDD_DMPLL C208 C218 C240
C210 C211 C201 2.2uF R2 M2 C231 25V R241 4.7uF EBF32593901 Deletion 10uF 0.1uF 0.1uF
4.7uF 4.7uF PC_L_IN 10V AUL2 GIN1P 0.047uF 33 COMP_Y+/AV_CVBS_IN 10V
ATV_1000P T1 N1 C232 25V R242 10V 16V 16V
10V 10V COMP_L_IN C216 2.2uF AUL3 RIN1M L202
10V 0.047uF 68

ZD200
Head Phone Head Phone C256 C217 2.2uF R3 N3 C233 25V R243 BLM18PG121SN1D

5V
SC1_R_IN 1000pF 10V AUR1 RIN1P 0.047uF 33 COMP_Pr+
C242 2.2uF R1 M3 C234 50V R205
PC_R_IN 50V 10V AUR2 SOGIN1 1000pF C205 C206
T3 10
AUDIO OUT COMP_R_IN C219 2.2uF
AUR3 SOC_RESET 10uF 0.1uF
C257 10V U2 10V 16V
SCART1_Lout 1000pF OPT C
AUOUTL0
50V ATV_1000P V3 D200
SCART1_Rout AUOUTR0
T2 MMBD6100 AVDD_AU33
C213 C220 AUVAG R200
1uF A2 A1 62K L200
10V 4.7uF
10V BLM18PG121SN1D
AUVRM
C215 C236 C241
BLM18SG121TN1D SB_MUTE
0.1uF 10uF 0.1uF
L214
16V 10V 16V

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS MT77 2013/09/16
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. MAIN2_NON_EU 52

Copyright ⓒ 2015 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes