General Purpose Relay

TA,TR Series

Part Number Description

T⇡




1a





⇢

⇡ Terminals Distance A : 5.08mm R : 7.62mm

⇢ Coil Voltage 05V : 5VDC 12V : 12VDC 24V : 24VDC

General Specification
Contact Form 1N/O
Contact Material Ag alloy (24K gold plate)
Maximum Contact Resistance 30mʃ
Rated Current(Resistance Load) 5A 30VDC 5A 250VAC
Contact Ratings Maximum Switching Current 5A
Maximum Contact DC 150W
Capacity AC 1,250VA
110VDC
Maximum Rated Voltage
250VAC

Data Processing
Minimum Switching Current * 1mA 5VDC
Coil Voltage 5VDC 12VDC 24VDC
Coil Consumption 120mW, 180mW
Coil Ratings Minimum Pick Up Voltage 70% of Nominal Voltage
Maximum Drop Out Voltage 5% of Nominal Voltage
Insulation Class F 155°C
Maximum Pick-up 6ms at nominal Voltage
Operating Time
Minimum Drop-out 3ms at nominal Voltage
Insulation Resistance Min. 1,000Mʃ (500VDC)
Dielectric Between Contact Points 1,000VACrms 1 minute
Strength Between Contact Points and Coil 2,000VACrms 1 minute
Surge Voltage Between Contact Points and Coil 4,000V
Mechanical Min. 10,000,000
Life Cycle
General Ratings Electrical Min. 100,000 (Under Rated Load)
Vibration Malfunction Min. 147m/s2(15G), 10 ~ 55Hz (width of vibration : 2.5mm)
Resistance Destruction Min. 205.8m/s2(21G), 10 ~ 55Hz (width of vibration : 3.5mm)
Shock Malfunction Min. 15G (147m/s2)
Resistance Destruction Min. 100G (980m/s2)
Ambient Temperature -40 ~ +70°C (with no icing)
Ambient Humidity 5% ~ 85% RH
Weight Approx. 3g

ó Please refer to the attention section.

ó Specifications and materials can be changed without prior notice for the enhancement of the quality.
* The minimum switching current is indicated as a standard value. The actual mininum switching rate is variable factor according to the make and break frequency,
environmental condition and anticipated credibility level. Therefore, it is recommended that tests be done to test actual load value before the production process.

Product Selection

Terminals Rated Terminals Rated

Distance Socket Voltage Part Number Distance Socket Voltage Part Number

5VDC TR-1a 5V 5VDC TA-1a 5V

7.62mm 12VDC TR-1a 12V 5.08mm 12VDC TA-1a 12V

TRS 24VDC TR-1a 24V TAS 24VDC TA-1a 24V

Rev. 2/14
Data subject may change without notice.
www.kacon.co.kr Industrial Controls Catalog Ǐ - 11
General Purpose Relay
TA,TR Series

Dimension (mm)

Relay Socket

TR-1a TA-1a TRS (Socket for TR Relay) TAS (Socket for TA Relay)

21.0 5.0
21.0 5.0 22.6 22.6
20.0 5.0 20.0 5.0

12.5
12.5

4-3.5
4-3.5

9.0
9.0
14.4

14.4
2-0.5 2-0.7 1.25 2-0.5 2-0.7 1.25 4-0.3
4-0.3
2.54 7.62 7.62 2.54 10.16 5.08

4.4

4.4
2-0.5 2-0.8 4-0.25 2-0.5 2-0.8 4-0.25
General Tolerance : ±0.3 General Tolerance : ±0.3 2.54 7.62 7.62 2.55 2.54 10.16 5.08 2.55

2-Ø1.2 2-Ø1.0 2-Ø1.2 2-Ø1.0

General Tolerance : ±0.3 General Tolerance : ±0.3

2-Ø1.2 2-Ø1.0 2-Ø1.2 2-Ø1.0

2.54 7.62 2.54 5.08

P.C. Board Pattern (bottom view) P.C. Board Pattern (bottom view)
2.54 7.62 2.54 5.08

P.C. Board Pattern (bottom view) P.C. Board Pattern (bottom view)
N.O COM N.O COM
Coil Coil

Schematic (bottom view) Schematic (bottom view)

Technical Data

1. Maximum Contact Capacity 2. Life Cycle Curve 3. (1) Coil Temperature Rise (120mW) 3. (2) Coil Temperature Rise(180mW)
Model : TA-1a 12V Model : TA-1a 24V
Ambient temperatures : 20°C Ambient temperatures : 20°C
Measured area : inner coil Measured area : inner coil

4. (1) Operating Time 4. (2) Operating Time 5. Specifications of 6. Failure shock

and cut-off (120mW) and cut-off (180mW) the ambient temperature
Model : TA-1a 12V Model : TA-1a 24V Model : TA-1a 12V

Caution

1. The operating voltage specification of Relay 2. When installing relay within 1mm close range,
according to method of relay attachment is as follows please pay attention to the followings

1) Relay installation must be 2) Coil terminal polarity must be

towards same direction towards same direction

Rev. 2/14
Ǐ - 12 Industrial Controls Catalog www.kacon.co.kr Data subject may change without notice.
General Purpose Relay
K505 Series

Part Number Description

K505





⇡




⇢

⇡ Contact Arrangement 2PL : 2N/O + 2N/C (LED) 4PL : 4N/O + 4N/C (LED)

⇢ Coil Voltage 12VDC 24VDC 100/110VDC

12VAC 50/60 Hz 24VAC 50/60 Hz

100/110VAC 50/60 Hz 110/120VAC 50/60 Hz 200/220VAC 50/60 Hz 220/240VAC 50/60 Hz

General Specification
Contact Form 2N/O + 2N/C 4N/O + 4N/C
Contact Material Ag alloy (24K gold plate)
Maximum Contact Resistance 50mǮ
2N/O + 2N/C 4N/O + 4N/C
Rated Current

Data Processing
(Resistance Load) 7A 30VDC 5A 30VDC
Contact Ratings 7A 250VAC 5A 250VAC
Maximum Switching Current 7A 5A

Maximum Contact DC 210W 150W

Capacity AC 1,750VA 1,200VA
Maximum Rated Voltage 125VDC / 250VAC
Minimum Switching Current * 100mA 5VDC
12VDC 24VDC 110VDC

Coil Voltage 12VAC 50/60 Hz 24VAC 50/60 Hz

100/110VAC 50/60 Hz 110/120VAC 50/60 Hz 200/220VAC 50/60 Hz 220/240VAC 50/60Hz

Coil Ratings DC Coil : 0.9W to 1.1W

Coil Consumption
AC Coil : 0.9VA to 1.2VA (60Hz)
Minimum Pick Up Voltage 80% of Nominal Voltage
10% of Nominal Voltage DC
Maximum Drop-out Voltage
30% of Nominal Voltage AC
Maximum Pick-up 20ms
Operating Time
Minimum Drop-out 20ms
Insulation Resistance 100MǮ at 500VDC
Between Contact Points: 1,000Vrms 1 minute
Dielectric Strength
Between Contact Points and Coil : 1,500Vrms 1 minute
General Ratings Mechanical : Min. 1,000,000
Life Cycle
Electronic : Min. 200,000
Vibration Resistant 10 ~ 55Hz (width of vibration 1.5mm)
Ambient Temperature -35 ~ +55°C (with no icing)
Ambient Humidity 30% ~ 80% RH
Weight Approx. 35g

ó Please refer to the attention section.

ó Specifications and materials can be changed without prior notice for the enhancement of the quality.
* The minimum switching current is indicated as a standard value. The actual mininum Switching rate is variable factor according to the make and break frequency,
environmental condition and anticipated credibility level. Therefore, it is recommended that tests be done to test actual load value before the production process.

Rev. 2/14
Data subject may change without notice.
www.kacon.co.kr Industrial Controls Catalog Ǐ - 13
General Purpose Relay
K505 Series

Product Selection

Part Number

Contact Form Socket Rated Voltage Illumination Weight (g)

2 Pole KPY2 220VAC K505-2PL 220VAC 35g
(2N/O + 2N/C) KMY2
KY08 110VAC K505-2PL 110VAC 35g
(For soldering)
24VAC K505-2PL 24VAC 35g
KY08-02
(For P.C Board) 110VDC K505-2PL 110VDC 35g

24VDC K505-2PL 24VDC 35g

12VDC K505-2PL 12VDC 35g

4 Pole KPY4 220VAC K505-4PL 220VAC 35g

(4N/O + 4N/C) KMY4
KMY4S 110VAC K505-4PL 110VAC 35g
KY14
24VAC K505-4PL 24VAC 35g
(For soldering)
KY14-02 110VDC K505-4PL 110VDC 35g
(For P.C Board)
24VDC K505-4PL 24VDC 35g

12VDC K505-4PL 12VDC 35g

Dimension (mm)

K505-2PL K505-4PL

6.3 ±0.1 6.3 ±0.1

8-Ø1.2x2.1 14-Ø1.2x2.1
2.5 ±0.1
2.5 ±0.1
0.5

0.5

28.0
28.0

36.0 21.5 DC Type AC Type 36.0 21.5 DC Type AC Type

ó Refer to the socket drawings at page Ǐ



Rev. 2/14
Ǐ - 14 Industrial Controls Catalog www.kacon.co.kr Data subject may change without notice.
General Purpose Relay
K705 Series

Part Number Description (Under development)

K705





⇡




⇢




⇣




⇤

⇡ Contact Arrangement 1P : 1N/O + 1N/C (Option) 2P : 2N/O + 2N/C 4P : 4N/O + 4N/C

⇢ Mounting & Terminal No mark : Socket-plug-in, Solder P : PC Board-pin

⇣ Option No mark : Standard L : LED indicator ( DC Coil : green, AC Coil : red )

LC : LED indicator
LD : LED indicator + freewheeling Diode (DC)
+ Built-in the Surge Adsorbent Circuit (AC)
⇤ Coil Voltage 12VDC 24VDC 100/110VDC

12VAC 50/60 Hz 24VAC 50/60 Hz

100/110VAC 50/60 Hz 110/120VAC 50/60 Hz 200/220VAC 50/60 Hz 220/240VAC 50/60 Hz

General Specification
Contact Form 2N/O + 2N/C 4N/O + 4N/C

Data Processing
Contact Material Ag alloy (24K gold plate)

Maximum Contact Resistance 50mʃ

2N/O + 2N/C 4N/O + 4N/C
Contact Ratings Rated Current
(Resistance Load) 5A 24VDC 5A 24VDC
5A 240VAC 5A 240VAC
Maximum Switching Current 5A 5A
Maximum Rated Voltage 125VDC / 250VAC
Minimum Switching Current* 100mA 5VDC
12VDC 24VDC 100/110VDC
Coil Voltage 12VAC 50/60 Hz 24VAC 50/60 Hz
100/110VAC 50/60 Hz 110/120VAC 50/60 Hz 200/220VAC 50/60 Hz 220/240VAC 50/60 Hz
DC Coils : Approx. 0.9W
Coil Ratings Coil Consumption
AC Coils : Approx. 0.9VA
Minimum Pick-up Voltage 80% of Nominal Voltage
10% of Nominal Voltage DC
Maximum Dropout Voltage
30% of Nominal Voltage AC
Max. Pickup : 20ms
Operating Time
Max. Dropout : 20ms
Insulation Resistance 100MǮ at 500VDC
Between Contact Points : 1,000Vrms 1 minute
Dielectric Strength
Between Contact Points and Coil : 1,500Vrms 1 minute
General Ratings Mechanical : Min. 1,000,000
Life Cycle
Electrical : Min. 100,000
Vibration Resistant 10 ~ 55Hz width of Vibration 1.5mm
Ambient Temperature -35 ~ +55°C (with no icing)
Ambient Humidity 35% ~ 80% RH
Weight 33g

ó Please refer to the attention section.

ó Specifications and materials can be changed without prior notice for the enhancement of the quality.
* The minimum switching current is indicated as a standard value. The actual mininum switching rate is variable factor according to the make and break frequency,
environmental condition and anticipated credibility level. Therefore, it is recommended that tests be done to test actual load value before the production process.

Rev. 2/14
Data subject may change without notice.
www.kacon.co.kr Industrial Controls Catalog Ǐ - 15
General Purpose Relay
K705 Series

Product Selection

Part Number

Rated llumination Weight

Contact Form Socket Voltage Non-Illumination Illumination Surge Absorption CircuitI (g)
2 Pole KMY2 220VAC K705-2P 220VAC K705-2PL 220VAC K705-2PLC 220VAC 33g
(2N/O + 2N/C) KY08
(For soldering) 110VAC K705-2P 110VAC K705-2PL 110VAC 33g
KY08-0
(For P.C Board) 24VAC K705-2P 24VAC K705-2PL 24VAC 33g

110VDC K705-2P 110VDC K705-2PL 110VDC 33g

24VDC K705-2P 24VDC K705-2PL 24VDC K705-2PLD 24VDC 33g

12VDC K705-2P 12VDC K705-2PL 12VDC 33g

4 Pole KMY4 220VAC K705-4P 220VAC K705-4PL 220VAC K705-4PLC 220VAC 33g
(4N/O + 4N/C) KMY4S
KY14 110VAC K705-4P 110VAC K705-4PL 110VAC 33g
(For soldering)
KY14-0 24VAC K705-4P 24VAC K705-4PL 24VAC 33g
(For P.C Board)
110VDC K705-4P 110VDC K705-4PL 110VDC 33g

24VDC K705-4P 24VDC K705-4PL 24VDC K705-4PLD 24VDC 33g

12VDC K705-4P 12VDC K705-4PL 12VDC 33g

Dimension (mm)

K705-2P Series K705-4P Series

K705-2PL K705-4PL
K705-2P DC Type AC Type K705-4P DC Type AC Type
2.6 2.6

8-Ø0.9x3.0 14-Ø0.9x3.0

0.5 0.5
K705-2PD K705-2PLD K705-2PLC K705-4PD K705-4PLD K705-4PLC

27 27

0.5 20.9 0.5 20.9

35.2 5.8 35.2 5.8

(bottom view) (bottom view)

đ K705 surge absorption circuit models contain a circuit to absorb with coil surge absorption diodes,
and models with coil surge absorption varistor circuits were used in

It is suitable to apply where malfunctioning or disturbances are likely to happen in such devices as PLC.

đ In case where relay Contact point (PLC relay output card) is tracked, damages on Contact points of other tracking devices are educed by
absorbing surge and it is possible to use high priced equipment for a long period of time.

ó Refer to the socket drawings at page Ǐ



Rev. 2/14
Ǐ - 16 Industrial Controls Catalog www.kacon.co.kr Data subject may change without notice.
General Purpose Relay
HR705 Series

Part Number Description

HR705





⇡




⇢




⇣




⇤

⇡ Contact Arrangement 1P : 1N/O + 1N/C (Option) 2P : 2N/O + 2N/C 3P : 3N/O + 3N/C (Option) 4P : 4N/O + 4N/C

⇢ Mounting & Terminal No mark : Socket-plug-in, Solder P : PC Board-pin

L : LED indicator ( DC Coil : green, AC Coil : red
⇣ Option No mark : Standard
)
LC : LED indicator
LD : LED indicator + freewheeling Diode (DC)
+ Built-in the Surge Adsorbent Circuit (AC)

⇤ Coil voltage 12VDC 24VDC 100/110VDC

12VAC 50/60 Hz 24VAC 50/60 Hz

100/110VAC 50/60 Hz 110/120VAC 50/60 Hz 200/220VAC 50/60 Hz 220/240VAC 50/60 Hz

General Specification

Data Processing
Contact Form 2N/O + 2N/C 4N/O + 4N/C
Contact Material Ag alloy (24K gold plate)
Maximum Contact Resistance Max. 50mʃ
2N/O + 2N/C 4N/O + 4N/C
Rated Current
Contact Ratings 5A 24VDC 5A 24VDC
(Resistance Load)
5A 240VAC 5A 240VAC
Maximum Switching Current 5A 5A
Maximum Rated Voltage 125VDC / 250VAC
Minimum Switching Current * 100mA 5VDC
12VDC 24VDC 100/110VDC
Coil Voltage 12VAC 50/60 Hz 24VAC 50/60 Hz
100/110VAC 50/60 Hz 110/120VAC 50/60 Hz 200/220VAC 50/60 Hz 220/240VAC 50/60 Hz
DC Coils : Approx. 0.9W
Coil Ratings Coil Consumption
AC Coils : Approx. 0.9VA
Minimum Pick-up Voltage 80% of Nominal Voltage
10% of Nominal Voltage DC
Maximum Drop-out Voltage
30% of Nominal Voltage AC
Maximum Pick-up 20ms
Operating Time
Minimum Drop-out 20ms
Insulation Resistance 100MǮ at 500VDC
Between Contact Points : 1,000Vrms 1 minute
Dielectric Strength
Between Contact Points and Coil : 1,500Vrms 1 minute
General Ratings Mechanical : Min. 1,000,000
Life Cycle
Electrical : Min. 100,000
Vibration Resistant 10 ~ 55Hz (width of Vibration 1.5mm)
Ambient Temperature -35 ~ +55°C (with no icing)
Ambient Humidity 35% ~ 80% RH
Weight Approx. 33g

ó Please refer to the attention section.

ó Specifications and materials can be changed without prior notice for the enhancement of the quality.
* The minimum switching current is indicated as a standard value. The actual mininum Switching rate is variable factor according to the make and break frequency,
environmental condition and anticipated credibility level. Therefore, it is recommended that tests be done to test actual load value before the production process.

Rev. 2/14
Data subject may change without notice.
www.kacon.co.kr Industrial Controls Catalog Ǐ - 17
General Purpose Relay
HR705 Series

Product Selection

Part Number

Rated llumination Weight

Contact Form Socket Voltage Non-Illumination Illumination Surge Absorption CircuitI (g)
2 Pole KMY2 220VAC HR705-2P 220VAC HR705-2PL 220VAC HR705-2PLC 220VAC 33g
(2N/O + 2N/C) KY08
(For soldering) 110VAC HR705-2P 110VAC HR705-2PL 110VAC 33g
KY08-02
24VAC HR705-2P 24VAC HR705-2PL 24VAC 33g
(For P.C Board)
110VDC HR705-2P 110VDC HR705-2PL 110VDC 33g

24VDC HR705-2P 24VDC HR705-2PL 24VDC HR705-2PLD 24VDC 33g

12VDC HR705-2P 12VDC HR705-2PL 12VDC 33g

4 Pole KMY4 220VAC HR705-4P 220VAC HR705-4PL 220VAC HR705-4PLC 220VAC 33g
(4N/O + 4N/C) KMY4S
KY14 110VAC HR705-4P 110VAC HR705-4PL 110VAC 33g
(For soldering)
24VAC HR705-4P 24VAC HR705-4PL 24VAC 33g
KY14-02
(For P.C Board) 110VDC HR705-4P 110VDC HR705-4PL 110VDC 33g

24VDC HR705-4P 24VDC HR705-4PL 24VDC HR705-4PLD 24VDC 33g

12VDC HR705-4P 12VDC HR705-4PL 12VDC 33g

Dimension (mm)

HR705-2P Series HR705-4P Series

HR705-2PL HR705-4PL
HR705-2P DC Type AC Type HR705-4P DC Type AC Type
2.6 2.6

8-Ø0.9x3.0 14-Ø0.9x3.0

0.5 0.5
HR705-2PD HR705-2PLD HR705-2PLC HR705-4PD HR705-4PLD HR705-4PLC

27 27

0.5 20.9 0.5 20.9

35.2 5.8 35.2 5.8

(bottom view) (bottom view)

đ HR705 surge absorption circuit models contain a circuit to absorb with coil surge absorption diodes,
and models with coil surge absorption varistor circuits were used in

It is suitable to apply where malfunctioning or disturbances are likely to happen in such devices as PLC.

đ In case where relay Contact point (PLC relay output card) is tracked, damages on Contact points of other tracking devices are educed by
absorbing surge and it is possible to use high priced equipment for a long period of time.

ó Refer to the socket drawings at page Ǐ



Rev. 2/14
Ǐ - 18 Industrial Controls Catalog www.kacon.co.kr Data subject may change without notice.
General Purpose Relay
HR710 Series

Part Number Description

HR710





⇡




⇢




⇣




⇤

⇡ Contact Arrangement 1P : 1N/O + 1N/C 2P : 2N/O + 2N/C 4P : 4N/O + 4N/C

⇢ Mounting & Terminal No mark : Blade-Style, Solder P : PC Board-pin (option)

⇣ Option No mark : Standard L : LED indicator ( DC Coil : green, AC Coil : red )

LC : LED indicator
LD : LED indicator + freewheeling Diode (DC)
+ Built-in the Surge Adsorbent Circuit (AC)

⇤ Coil Voltage 12VDC 24VDC 100/110VDC

12VAC 50/60 Hz 24VAC 50/60 Hz

100/110VAC 50/60 Hz 110/120VAC 50/60 Hz 200/220VAC 50/60 Hz 220/240VAC 50/60 Hz

General Specification

Data Processing
Contact Form 1N/O + 1N/C 2N/O + 2N/C 4N/O + 4N/C
Contact Material Ag alloy (24K gold plate)
Maximum Contact Resistance 50mʃ
1N/O + 1N/C 2N/O + 2N/C 4N/O + 4N/C
Rated Current
Contact Ratings 15A 24VDC 10A 24VDC
(Resistance Load)
15A 220VAC 10A 220VAC
Maximum Switching Current 15A 10A
Maximum Rated Voltage 125VDC / 250VAC
Minimum Switching Current * 100mA 5VDC
12VDC 24VDC 100/110VDC
Coil Voltage 12VAC 50/60 Hz 24VAC 50/60 Hz
100/110VAC 50/60 Hz 110/120VAC 50/60 Hz 200/220VAC 50/60 Hz 220/240VAC 50/60 Hz
1P, 2P DC Coil = Approx. 0.9W / 4P DC Coil = Approx. 1.5W
Coil Ratings Coil Consumption
1P, 2P AC Coil = Approx. 1.2VA / 4P AC Coil = Approx. 2.5VA
Minimum Pick-up Voltage 80% of Nominal
10% of Nominal Voltage DC
Maximum Drop Out Voltage
30% of Nominal Voltage AC
Maximum Pick-up 25ms
Operating Time
Minimum Drop-out 25ms
Insulation Resistance 100MǮ at 500VDC
Between Contact Points : 1,000Vrms 1 Minute.
Dielectric Strength
Between Contact Points and coil : 1,500Vrms 1 Minute.
General Ratings Mechanical : Min. 1,000,000
Life Cycle
Electrical : Min. 100,000
Vibration Resistant 10 ~ 55Hz (width of vibration 1.5mm)
Ambient Temperature -25 ~ + 55°C (with no icing)
Ambient Humidity 35% ~ 80% RH
Weight 2P : Approx. 33g , 4P : Approx. 65g

ó Please refer to the attention section.

ó Specifications and materials can be changed without prior notice for the enhancement of the quality.
* The minimum switching current is indicated as a standard value. The actual mininum Switching rate is variable factor according to the make and break frequency,
environmental condition and anticipated credibility level. Therefore, it is recommended that tests be done to test actual load value before the production process.

Rev. 2/14
Data subject may change without notice.
www.kacon.co.kr Industrial Controls Catalog Ǐ - 19
General Purpose Relay
HR710 Series

Product Selection

Part Number
Rated Illumination Weight
Contact Form Socket Voltage Non-Illumination Illumination Surge Absorption Circuit (g)
1 Pole 220VAC HR710-1P 220VAC HR710-1PL 220VAC HR710-1PLC 220VAC 33g
(1N/O + 1N/C)
110VAC HR710-1P 110VAC HR710-1PL 110VAC 33g
24VAC HR710-1P 24VAC HR710-1PL 24VAC 33g
110VDC HR710-1P 110VDC HR710-1PL 110VDC 33g
24VDC HR710-1P 24VDC HR710-1PL 24VDC HR710-1PLD 24VDC 33g
12VDC HR710-1P 12VDC HR710-1PL 12VDC 33g
2 Pole KLY2 220VAC HR710-2P 220VAC HR710-2PL 220VAC HR710-2PLC 220VAC 33g
(2N/O + 2N/C) KT08
110VAC HR710-2P 110VAC HR710-2PL 110VAC 33g
(For soldering)
KY08-0 24VAC HR710-2P 24VAC HR710-2PL 24VAC 33g
(For P.C Board)
110VDC HR710-2P 110VDC HR710-2PL 110VDC 33g
24VDC HR710-2P 24VDC HR710-2PL 24VDC HR710-2PLD 24VDC 33g
12VDC HR710-2P 12VDC HR710-2PL 12VDC 33g
4 Pole KLY4 220VAC HR710-4PL 220VAC HR710-4PLC 220VAC 65g
(4N/O + 4N/C) KTF14A
110VAC HR710-4PL 110VAC 65g
24VAC HR710-4PL 24VAC 65g
110VDC HR710-4PL 110VDC 65g
24VDC HR710-4PL 24VDC HR710-4PLD 24VDC 65g
12VDC HR710-4PL 12VDC 65g

Dimension (mm)

HR710-1P Series HR710-2P Series

5.0 5.0
HR710-1P HR710-1PL HR710-2P HR710-2PL

8-Ø2.5 8-Ø2.5
0.5 0.5

27 27

5.0 5.0

3.0 20.9
3.0 20.9 DC Type AC Type 34.7 6.8 DC Type AC Type
34.7 6.8
(Bottom View) (Bottom View)

HR710-4P Series
HR710-4P Series HR710 (SurgeHR710
Absorption type)
(surge absorption)

HR710-4P HR710-4PL HR710-2PLD HR710-2PLC

4.8

14-Ø2.5
0.5 DC Type AC Type
(Bottom View) DC Type AC Type
27 (Bottom View)
4.8
HR710-4PLD HR710-4PLC
3.0 40.7
34.6 7.2

đ HR710 surge absorption contains a circuit to absorb with coil surge absorption diodes, and
models with coil surge absorption varistor circuits were used in. It is suitable to apply
where malfunctioning or disturbances are likely to happen in such devices as PLC.

đ In case where relay contact (PLC relay output card) is tracked, damages on contacts of DC Type AC Type
(Bottom View)
other tracking devices are reduced by absorbing surge and it is possible to use high
priced equipment for a long period of time.

Rev. 2/14
Ǐ - 20 Industrial Controls Catalog www.kacon.co.kr Data subject may change without notice.
General Purpose Relay
HR707N Series

Part Number Description

HR707N





⇡




⇢




⇣




⇤

⇡ Contact Arrangement 2P : 2N/O + 2N/C 3P : 3N/O + 3N/C

⇢ Option No mark : Standard (Mechanical indicator equipped ) L : LED Indicator ( DC Coil : Green, AC Coil : Red )
LC : LED Indicator
LD : LED Indicator + Freewheeling Diode (DC)
+ Built-in the Surge Adsorbent Circuit (AC)

⇣ Coil Voltage 12VDC 24VDC 100/110VDC

12VAC 50/60 Hz 24VAC 50/60 Hz 100/110/120VAC 50/60 Hz 200/220VAC 50/60 Hz 220/240VAC 50/60 Hz

General Specification
Contact Form 2N/O + 2N/C 3N/O + 3N/C

Data Processing
Contact Material Ag alloy (24K gold plate)
Maximum Contact Resistance 50mǮ

Rated Current 2N/O + 2N/C 3N/O + 3N/C

(Resistance Load) 10A 28VDC
Contact Ratings
10A 250VAC
Maximum Switching Current
10A
Maximum Rated Voltage 250VDC / 250VAC
Minimum Switching Current * 100mA 5VDC
12VDC 24VDC 100/110VDC
Coil Voltage 12VAC 50/60 Hz 24VAC 50/60 Hz
100/110/120VAC 50/60 Hz 200/220VAC 50/60 Hz 220/240VAC 50/60 Hz
DC : 1.6W Approx.
Coil Ratings Coil Consumption
AC : 2.4VA Approx.
Minimum Pick-up Voltage 80% of Nominal
10% of Nominal Voltage DC
Maximum Drop Out Voltage
30% of Nominal Voltage AC
Maximum Pick-up 30ms
Operating Time
Minimum Drop-out 20ms
Insulation Resistance 100MǮ at 500VDC
Between Contact Points : 1,000Vrms for 1 minute.
Dielectric Strength
Between Contact Points and Coil : 1,500Vrms for 1 minute.
General Ratings Mechanical : Min. 10,000,000
Life Cycle
Electrical : Min. 100,000
Vibration Resistant 10 ~ 55Hz width of vibration 1.5mm
Ambient Temperature -10 ~ +40°C (with no icing)
Ambient Humidity 35% ~ 80%RH
Weight Approx. 75g

ó Please refer to the attention section.

ó Specifications and materials can be changed without prior notice for the enhancement of the quality.
* The minimum switching current is indicated as a standard value. The actual mininum Switching rate is variable factor according to the make and break frequency,
environmental condition and anticipated credibility level. Therefore, it is recommended that tests be done to test actual load value before the production process.

Rev. 2/14
Data subject may change without notice.
www.kacon.co.kr Industrial Controls Catalog Ǐ - 21
General Purpose Relay
HR707N Series

Product Selection

Part Number

Rated Illumination Weight

Contact Form Socket Voltage Non-Illumination Illumination Surge Absorption Circuit (g)
2 Pole KF083A
220VAC HR707N-2P 220VAC HR707N-2PL 220VAC HR707N-2PLC 220VAC 75g
(2N/O + 2N/C) KPZ2

110VAC HR707N-2P 110VAC HR707N-2PL 110VAC 75g

110VDC HR707N-2P 110VDC HR707N-2PL 110VDC 75g

24VDC HR707N-2P 24VDC HR707N-2PL 24VDC HR707N-2PLD 24VDC 75g

3 Pole KF113A
220VAC HR707N-3P 220VAC HR707N-3PL 220VAC HR707N-3PLC 220VAC 75g
(3N/O + 3N/C) KPZ3

110VAC HR707N-3P 110VAC HR707N-3PL 110VAC 75g

110VDC HR707N-3P 110VDC HR707N-3PL 110VDC 75g

24VDC HR707N-3P 24VDC HR707N-3PL 24VDC HR707N-3PLD 24VDC 75g

Dimension (mm)

HR707N-2P Series HR707N-3P Series

34.5 34.5

34.5 0.8 52.5 2P 34.5 0.8 52.5 3P

HR707N-2P HR707N-2PL HR707N-2PL HR707N-3P HR707N-3PL HR707N-3PL

AC Type DC Type
AC Type DC Type
(Bottom View)
(Bottom View)
HR707N (surge absorption type)

HR707N-2PLC HR707N-2PLD HR707N-3PLC HR707N-3PLD

AC Type DC Type AC Type DC Type

đ HR707N surge absorption models contains a circuit to absorb the noises that are produced from relay while relay
tracking. It is suitable to apply where malfunctioning or disturbances are likely to happen in such devices as PLC.

đ In case where relay Contact point (PLC relay output card) is tracked, damages on Contact points of other tracking devices are
reduced by absorbing surge and it is possible to use high priced equipment for a long period of time.

Rev. 2/14
Ǐ - 22 Industrial Controls Catalog www.kacon.co.kr Data subject may change without notice.
 Data Processing

Product Selection & Dimension (mm)

Part Number
Certification Relay Dimension
(Color)

2-Ø3.0
M3 3.5

23.0

KPY2

3.0

+0.2
0
K505-2P

75.0

39.5
55.0
(White)

23.0 24.0
27.0 (TOP VIEW)

2-Ø3.0
M3 3.5

23.0

KPY4

3.0

+0.2
0
75.0

39.5
55.0
K505-4P
(White)

Data Processing
23.0 24.0
27.0 (TOP VIEW)

Module

KPY-M KPY-D

KPY-M1 24VDC/AC 6 ~ 250VDC

KPY-M2 110VDC/AC KPY socket
KPY-M3 220VDC/AC
KPY socket

Varistor Diode

2-Ø4.5

M3
4.0
6.0 26

K505-2P 4
45 35.4
KMY2 62

HR705-2P
4

15
4 26
25
30
(TOP VIEW)

2-Ø4.5
M3
4.0
6.0
26

KMY4
(R, G, Y, B, K505-4P 62
4
45 35.4

Amber, HR705-4P
4

Black(Basic)) 15
4 26
25
30
(TOP VIEW)

2-Ø4.5
22 M3.5 18
6
26

KLY2 HR710-2P 67 47 35.4

14.5
2.5 26
30 25 (TOP VIEW)

Rev. 2/14
Data subject may change without notice.
www.kacon.co.kr Industrial Controls Catalog Ǐ - 23
General Purpose Relay

Product Selection & Dimension (mm)

Part Number Certification Relay Dimension

2-Ø4.5
M3.5 18
42
8 3.2
46

KLY4 HR710-4P 67 47 35.4

2.5 46
14.5
50
25 (TOP VIEW)

2-Ø4.5X6.0mm
29.5
46.0 max

36.0 36.0
M3.5

3.5

KTF14A HR710-4P

49.8

35.5
78.5 max
68.0
19.6

(TOP VIEW)

2-Ø4.5

8-M3.5x7 4
7
33±0.2

2-Ø4.2

KF083A HR707N-2P 52min

35.4

3.5 2
4 33
41min 21min

(TOP VIEW)

2-Ø4.5
11-M3.5x7
22 7 4
34±0.2

KF113A HR707N-3P 52min

35.4

4 3.5 2
5 34 4 31min
43min
(TOP VIEW)

2-Ø3.2
8-M3X8

HR707N-2P 27.5
2-Ø3.2

61.5 max
25.6

KPZ2 TTL
37.0

TTS
8-Ø2.8

27.5
26.0 max
38.0 max

2-Ø3.2
11-M3X8
2-Ø3.2

27.5
25.6

61.5 max

KPZ3 HR707N-3P
37.0
8-Ø2.8

27.5
26.0 max
38.0 max

Rev. 2/14
Ǐ - 24 Industrial Controls Catalog www.kacon.co.kr Data subject may change without notice.
 Data Processing

Product Selection & Dimension (mm)

Part Number Certification Relay Dimension

25±0.2

21.4 +0.2
0
(TOP VIEW)
K505-2PL
KY08
HR705-2P Soldering 13.2

5.8 4.1
25.5 29.5

12.65
6.35
7.7
2.7 2.6 6.4
20 24
4.2 8-Ø1.3

25.8±0.2

21.4 +0.2
0
(TOP VIEW)
KY11 HR705-3P Soldering

Data Processing
13.2

4.1
5.8
25.5 29.5

12.65
6.35
7.7
2.6 6.4
2.7
20 24
4.2 11-Ø1.3

25.8±0.2

K505-4P 21.4 +0.2

0
KY14 (TOP VIEW)

HR705-4P Soldering 13.2

4.4
25.5 29.5 4.1
5.8

7.7 12.65
2.6 6.35
2.7
20 24
6.4

4.2 14-Ø1.3

25.8±0.2

K505-2P 21.4 +0.2

0
KY08-02 0.3 (TOP VIEW)
HR705-2P PCB Type 13.2

4.1
25.5 29.5 5.8

4.3 12.65
6.35
2.7 22
16.5 6.4

4.2 8-Ø1.3

25.8±0.2

21.4 +0.2
0
(TOP VIEW)
KY11-02 HR705-3P PCB Type 0.3
13.2

4.1
5.8
25.5 29.5

12.65
6.35
4.3
2.7 22 6.4
16.5
4.2 11-Ø1.3

25.8±0.2

21.4 +0.2
0
K505-4P (TOP VIEW)
KY14-02 0.3
13.2
HR705-4P PCB Type 4.4
25.5 29.5 4.1
5.8

4.3 12.65
22 6.35
2.7
16.5 6.4

4.2 14-Ø1.3

Rev. 2/14
Data subject may change without notice.
www.kacon.co.kr Industrial Controls Catalog Ǐ - 25
General Purpose Relay

Product Selection & Dimension (mm)

Part Number Certification Relay Dimension

3.6

25.8±0.2

21.4 +0.2
0
(TOP VIEW)
KT08 HR710-2P Soldering 0.3
10

4.6
25.5 29.5

5.35
12.45
6.45
8-Ø1.7 24
2.7 6.5
20.5
8-Ø2.5

15.6

25.8±0.2

21.4 +0.2
0
(TOP VIEW)

KT08-0 HR710-2P PCB Type 10

0.3
4.6

2 25.5 29.5 5.35

12.45
6.45
6.5
1 4.3
22 8-Ø2.5
18
15.6

2-Ø4.5
8-M3.5X7.5 7.8 3 4.5

40±0.2

K2CF08 TTL 70min

35.4

2-Ø4.5

4 50min 20.3min
(TOP VIEW)

2-Ø4.5
8-M3.5X7.5 5 4.5
7.8

40±0.2

K2CF08K Waterlevel, FLR 70min

35.4

2-Ø4.5

4 50min 20.3min
(TOP VIEW)

22.6
20.0 5.0

TAS
9.0

TA-1a
14.4

2-Ø1.2 2-Ø1.0
(White)
4.4

2-0.5 2-0.8 2.54 5.08

4-0.25
10.16 5.08
2.54 2.55

22.6
20.0 5.0

TRS
9.0

TR-1a
14.4

2-Ø1.2 2-Ø1.0
(White)
4.4

2-0.5 2-0.8 2.54 7.62

4-0.25
7.62 7.62
2.54 2.55

Rev. 2/14
Ǐ - 26 Industrial Controls Catalog www.kacon.co.kr Data subject may change without notice.
 Data Processing

Product Selection & Dimension (mm)

Part Number Certification Relay Dimension

30 31
2-Ø4.5

20
26

KMY4S K505-4P
HR705-4P 70
M3
G (Green) 35.5

6 (TOP VIEW)

80.7
42.5
31.2 33.2
24

K505-4P
KCY4
HR705-4P

Data Processing
35 95.5

(TOP VIEW)
2

40.0

8-M3.5X6
28.5
21.0

K2BF08 TTL 49.0

8.2 9.5

(Bottom View)

45.0 26. 5 17.5

11-M3.5X6
8.5 7.0

K2BF11 TTL 45.0

34.0

(Bottom View)

Rev. 2/14
Data subject may change without notice.
www.kacon.co.kr Industrial Controls Catalog Ǐ - 27