1.

Contents 2

1. Contents Page

2. Assembly, putting into operation, connection 3

3. Control elements 4

4. Display 4

5. Factory setting 5

6. Changing settings 6

6.1 Time and day of the week 6

6.2 Calendar month and day 7

6.2.1 AU = Automatic changeover 7

6.2.2 cHA = Weekday-related time change 8-9

6.2.3 no = no changeover 10

7. Standard switching commands 11

8. Weekday block formation 12 - 13

9. Read – change – delete – reset 14 - 15

10. Hand switch 16

11. Technical data 17

GB
Downloaded from www.Manualslib.com manuals search engine
 2. Assembly, putting into operation, connection 3

2.1 Assembly
Fit the time switch
• on a DIN rail
• optional wall surface-mounting
Surface-mounting set for 2 and
3 module spacings
Article No. 03.53.0083.2
2.2 Putting into operation
The time and date are set at the factory.
The time switch is in Energy-saving mode.
Only the colon flashes.
Press any key:
• The time switch is actived
• It displays the time (day of the week)

2.3 Connection
See information on the unit!
Press any key to activate the time switch
• the time and date is displayed
AC Note:
DC + –
If no key is pressed the time switch is
automatically activated after approx
1 - 2 minutes.

Safety instruction:
AC • When operating the clock safety low
DC + – voltage, only safety low voltage may
be connected.
• When operating the clock with function
low voltage, mains voltage (230 ~) or
function low voltage may be connected.
The connection of safety low voltage is
not admissible in this case.

Downloaded from www.Manualslib.com manuals search engine

 3. Control elements 4

Start program input Hand switch

Set time,
end program input
Enter pulse/
cycle
Select day(s)
Reset
of the week
Delete switching time Set minutes, month, year
Set hours, day, year Summer time/winter time switchover

4. Display

Date 1234567 =
days of the week
Summer time 1 = Monday
display

AM/PM Hours - current time

display Calendar day - current date
- start/end
DCF 77 summer time
reception Minutes - current time
Month - current date
Channel 1 - start/end
Channel 2 summer time
Year - day/month
Switching state
Pulse/cycle

Continuous operation

Automatic mode Manual operation

GB
Downloaded from www.Manualslib.com manuals search engine
 5. Factory setting 5

The selections correspond to Central European Time. The time

switch offers 3 Operating modes. The date and time, and also
the Operating mode AU are set.
Operating modes:
• AU Automatic summer time controller switchover
see 6.2.1
The switchover occurs on the dates defined by
the legislator.
• cHA Weekday-related summer time controller
switchover, see 6.2.2
You enter the start and end dates of summer time
which applies to your location/country.
e. g. The first Sunday in April of the current year
(start of summer time)
The last Sunday in October of the year
(end of summer time)
In the following years, changeover always occurs
on the right day of the week in the correct calendar
week.
• no No changeover, see 6.2.3
AM/PM switch-over
Switch clock is in current operating mode
1. Press h and keep pressed
2. – Press Res once
– all segments are displayed
– after approx. 1 second the following appears:
AM, 12.00 and 3 (Wednesday)
Operating mode AU is active = works setting
3. Release h
4. Select operating mode as required, see 6.2.1 or 6.2.2 or 6.2.3
5. Set the current time of day and weekday, see 6.1

Downloaded from www.Manualslib.com manuals search engine

 6. Changing settings 6

Note:
You can exit/conclude any adjustments, changes you make
at any time with the key .

6.1 Time and day of the week

Press the key once

Set the time:

With the h key – hours
With the m key – minutes

Note for weekly time switch:

If the Operating mode
no = no change
- see 6.2.3
was selected, the day of the
week must now be set.
With the Day 1 - Monday
key select: 2 - Tuesday
3 - Wednesday
:
7 - Sunday

Press the key once.

The input is ended.

GB
Downloaded from www.Manualslib.com manuals search engine
 6.2 Calendar month and day – Select the Operating mode 7

6.2.1 AU or 6.2.2 cHA or 6.2.3 no

6.2.1 AU = Automatic changeover

Press the key once

Press the + 1h key 1 once,

AU appears

Press the Prog key once

Set the current year:

With the m key or the h key

Confirm with the Prog key

Set the current month and day:

With the m key – calendar month
With the h key – calendar day
Note:
With the Prog key (press once or
twice), read the date for the start
e.g. 29.03. and end e.g. 25.10.
of summer time.
Press the key once.
The input is ended.

Downloaded from www.Manualslib.com manuals search engine

 6.2.2 cHA = Weekday – related time change 8

Press the key once

Press the + 1h key as often as

necessary until cHA appears

Press the Prog key once

Set the current year:

With the m key or the h key

Confirm with the Prog key

Set the current month

and day:
With the m key – calendar month
With the h key – calendar day

GB
Downloaded from www.Manualslib.com manuals search engine
 9

Confirm with the Prog key

The start of summer time is
displayed.

Set the individual

summer time start:
With the m key – month
With the h key – day

Confirm with the Prog key

Set individual
summer time end:
With the m key – month
With the h key – day

Press the key once.

The input is ended.

Downloaded from www.Manualslib.com manuals search engine

 6.2.3 no = no changeover – only weekly time switch 10

Press the key once

Press the + 1h as often as

necessary until no appears.
The time switch operators
without a date!

Press the key once.

The input is ended.

Note:
Select day of the week
see 6.1

GB
Downloaded from www.Manualslib.com manuals search engine
 7. Standard switching commands 11

You determine the switching times and the switching state for the relevant
switching output (channel.) Symbol: CH1: (ON) = Channel 1
CH2: (OFF) = Channel 2
These assignments are possible:
• Switching commands only for channel 1
• Switching commands only for channel 2
• The same switching commands for channel 1 and channel 2
(the switching time and switching state are identical)
• The same switching time for channel 1 and channel 2 but with a
different switching state.
Select free memory location:
Press the Prog key as often as
necessary until – –:-– – appears.

Set the switching times:

With the m key – minutes
With the h key – hours
For weekday adjustment, see:
Block formation of weekdays, Point 8
Set the switching state:
With the key
(ON) or (OFF)
Note:
The switching state for CH1 or
CH2 can be deactivated.
No symbol – no switching.
Press the Prog key once. The input has
ended. A free memory location is
displayed – for other settings or
Press the key once. The input
is ended.
The display shows the current time.
Downloaded from www.Manualslib.com manuals search engine
 8. Fixed weekday block formation – only weekly time switch 12

Defined combinations of weekdays or individual days

You determine the weekdays for your switching program.
1 - Monday, 2 - Tuesday, 3 - Wednesday ..., 7 - Sunday
Example: Monday … Friday (8:00 ON; 22:00 OFF)
Select free memory location:
Press Prog key as often as
necessary until – –:– – appears

Press the Day key once

All 7 days of the week are activate

Activating/deactivating
days of the week:
Jog the Day key stepwise

1 2 3 4 5 6 7
– – – – – –
– – – – –
– –
–
–
–
–
–
–
–
Note:
Enter the switching times and the switching state = ON; = OFF for the
relevant switching state (channel). For standard switching commands, see 7.

GB
Downloaded from www.Manualslib.com manuals search engine
 13

Press the Prog key once.

The input is ended.
A free memory location is
displayed - for further settings
or
press the key 1once.
The input is ended.
The display shows the
current time.

Note:
After the procedures
• read, modify or delete
the time, date, switching
program
• DCF synchronisation
• restoration of mains power
the switching state of the time
switch is updated automatically.

Downloaded from www.Manualslib.com manuals search engine

 9. Read – change – delete – reset 14
• You can read the program contents stepwise
• You can change or overtype the program contents
• You can delete the program contents
• You can delete the date and time
Read
Press the Prog key step by step
Each individual content is dis-
played until the end of the program.
Then:
• One free memory location
– –:– –
• One digit (free memory locations)
(ex. Fr 10)

Change
Press the Prog key step by step
as far as the switching
command/contents which you
want to change/overtype.
Change the switching command/
contents:
As described in
8. Weekday block formation

Delete - individual switching commands

Press the Prog key step by
step as far as the switching
command/contents which you
want to delete.
Press the Clear key once.
This switching command
is deleted.

GB
Downloaded from www.Manualslib.com manuals search engine
 15

Delete - All switching commands

Press the Prog key as often as
necessary until FRxx appears

Press the Clear key once.

CL is in the display

Press the Clear key and hold it down.

All memory locations are deleted!

The display shows the number

of the max. memory locations.
Reset
Press the Reset key once

The set date and time are reset.

The factory setting

AU = automatic s/w-
time changeover is active
(31.12.1997, 00:00)

All segments are visible for

approx. 2 seconds,
then 00:00 appears.

AU = automatic s/w time

changeover
See point 5 and 6 for
setting the current date.

Downloaded from www.Manualslib.com manuals search engine

 10. Hand switch 16

You change – manually – the current switching state.

However, the individually set switching program is preserved.
1 for channel 1
2 for channel 2

= automatic = Manual mode FIX = continuous operation

= OFF = ON FIX = Continuous ON

= ON = OFF FIX = Continuous OFF

The switching state You change You change

corresponds to the – m a n u a l l y – – m a n u a l l y –
entered program. the current switching the current switching
state. state.
The next switching Only with the key
command in the do you switch from
program is executed continuous operation
automatically again. back to Automatic
mode.

GB
Downloaded from www.Manualslib.com manuals search engine
 11. Technical data 17

1 channel daily program 1 channel weekly program

2 channel weekly program

Dimensions (H x W x D) mm 45 x 36 x 60 45 x 36 x 60
Distributor cut-out mm 46 x 36 46 x 36
Weight g (approx.) 170 170
Connection see unit imprint see unit imprint
Power consumption: see unit imprint see unit imprint
Switching capacity at 230 V AC
– ohmic load (VDE, IEC) 16 A/250 V AC 16 A/250 V AC
– inductive load cos ϕ 0,6 2,5 A/250 V AC 2,5 A/250 V AC
– glow lamp load 1000 W 1000 W
Switching output potential-free potential-free
Switching contacts 1 or 2 changeover contacts 1 or 2 changeover contacts
Protection class II
Protection type IP 20
Running accuracy ± 2.5 s/day at +20° C ± 2.5 s/day at +20° C
DCF 77 radio operation – –
Running reserve type Lithium Lithium
Running reserve 3 years from factory 3 years from factory
Shortest switching time 1 minute 1 minute
Programmable every minute every minute
Memory locations 12 20/30
Switching preselection yes yes
Hand switch Automatic/preselection Automatic/preselection
Fix ON Fix ON
Fix OFF Fix OFF
Switching state display yes yes
Block formation of weekdays – fixe assignment
Summer/winter time switchover automatic/freely selectable automatic/freely selectable
Connection type captive +/– screw terminals captive +/– screw terminals
Ambient temperature - 25° C … + 55° C - 25° C … + 55° C
Led sealable yes yes

Downloaded from www.Manualslib.com manuals search engine