86758919
01 / 2014
Rev 00
025MTa160WB45- WL-
Q
T
+
1.5
1.2
1.3
1.4 1.1
86758885
MAINTENANCE LEGEND
PARTS TO CHANGE
Depending on applications.
Every 100 hours.
Every 400 hours.
Every 800 hours.
Every 1600 hours.
Long term, only if damaged.
CAUTION
If drifter settings are incorrect, wear parts can be damaged prematurely.
If the drifter is used with deflated accumulators, premature damage can be caused to all parts.
These inspection intervals can vary depending on ground conditions, use of drifter.......
E MONTABERT HC25 - 2014
x ?? CPN Desription
025MTa****B45**L-
10 1 86714383 Carter
63 Nm 70 20 1 86714466 Cylinder
46 ft.lb 30 1 86250107 Drive component
37 Nm 60 40 1 86221595 Drive component
120
27 ft.lb 50 1 86679388 Seal
130 140 60 1 86715489 Upper cylinder
100 80
70 1 86624160 Pin
170
80 1 86715414 Strike piston
110
+ 90 90 1 86715422 Distributor
50
100 1 86714490 Upper flange
110 1 86633922 Diaphragm
80 Nm 120 12 95421335 UNF3/8”, socket head screw
59 ft.lb 130 1 86600632 Valve
235 mm mini
190 9.25” mini 140 1 86580966 Threaded plug
150 1 95303368 Adaptor
180 20 160 2 95303384 Adaptor
52 Nm 170 1 86715448 Push
38 ft.lb 40 180 1 86418357 Plug
190 2 86632916 Plug
200 2 86263233 Plug
200
210 1 86247723 Plug
80 Nm PARTS TO CHANGE
160 59 ft.lb
Depending on applications.
80 Nm
210 Every 100 hours.
59 ft.lb
30 10 150 52 Nm
Every 400 hours.
38 ft.lb
52 Nm
Every 800 hours.
38 ft.lb
11807
Every 1600 hours.
( 02 / 2013 ) - rev 05
Long term, only if damaged.
1.1
1.2
E MONTABERT HC25 - 2014
025MTa 160*B45**L- 55 Nm 80 Nm 300
x ??
1
CPN
86697083
Description
Hydraulic motor
410 430
40 ft.lb 59 ft.lb 310 1 86668670 Rear cover
320 1 86715430 Piston cover
330 1 86668860 Thrust
340 1 86668886 Ring
350 1 86712403 Ring
360 1 86684263 Seal
370 1 86668696 Motor shaft
152 Nm
112 ft.lb 380 380 1 86350857 O’ring
390 8 95234712 UNF1/2”, socket head screw
390
400 4 86548609 M12, socket head screw
310 410 2 86330107 Adaptor
400
420 1 86420098 O’ring
102 Nm
420
300 75 ft.lb
340 430 2 86247723 Plug
330
350 370
320
360
PARTS TO CHANGE
Depending on applications.
Every 100 hours.
Every 400 hours.
Every 800 hours.
11810
Every 1600 hours.
( 02 / 2013 ) - rev 05
Long term, only if damaged.
E MONTABERT HC25 - 2014
WB45 - WL-
x ?? CPN Designation
025MTa*** 690
500 1 86715455 Front guide
510 1 86736311 Ring
650
520 1 86582558 Snap ring
530 8 86715943 UNF1/2”, hexa. screw
630
540 8 86467032 Washer
670 550 1 86715463 Ring
590
680 560 1 95303335 Adaptor
570 1 86726734 Seal kit
640 580 1 86728698 Front cover
590 2 86267069 O’ring
660 600 1 86684271 Seal
610 1 86735073 Retainer shank
600 620 1 86732526 O’ring
630 1 86732575 Spline shank + Ring
620 640 1 86624160 Pin
650 1 86737376 Shank stop
580
570 850 Nm 660 1 86473303 O’ring
610 670 1 86676822 Roller thrust
627 ft.lb
680 1 86676889 Ring
690 1 86715554 Lip seal
700
500
560 52 Nm 700 1 86247723 Plug
550 38 ft.lb
52 Nm PARTS TO CHANGE
510 38 ft.lb Depending on applications.
520 Every 100 hours.
540 Every 400 hours.
530 Every 800 hours.
126 Nm 11929
Every 1600 hours.
93 ft.lb ( 02 / 2013) - rev 02
Long term, only if damaged.
1.3
1.4
E MONTABERT HC25 - 2014
x ?? CPN Desription
025MTa****B45**L- 800 1 86758661 Shank (H25 female)
A 1 86739018 Control gauge kit
A
A 86730942
+
86739000
800
218
H25F
PARTS TO CHANGE
Depending on applications.
Every 100 hours.
Every 400 hours.
Every 800 hours.
12063
Every 1600 hours.
( 02 / 2013 ) - rev 02
Long term, only if damaged.
E MONTABERT - 2014
86350857
380
025MTa***********
- 86732823-
86420098
420
86684263
360
86679388 86715554
50 690
86473303
660
86684271
600
86732526
620
Old version
86668944
660
570 86267069
570 590
570
- 86726734 -
1.5
203, route de Grenoble
CS 80097
69805 St PRIEST CEDEX
FRANCE www.montabert.com
